Color Monitor. L200p. English. User s Guide

Transcription

1 Color Montor L200p User s Gude Englsh

2 Frst Edton (February / 2003) Note : For mportant nformaton, refer to the Montor Safety and Warranty manual that comes wth ths montor.

3 Contents ENGLISH Safety (Read frst)...2 Settng up the montor...3 Product Descrpton...3 Handlng Instructons...3 Workplace preparaton...4 Adjustng the Montor Poston...5 Workng Practces...6 Carng for your Montor...6 Connectng your Montor...7 Swtchng on your Montor...8 Devce Drver Installaton...9 Wndows 95/ Wndows 2000/Me...10 Wndows XP...11 Automatc Image Setup...12 Image Setup...12 Image Setup for DOS...13 Image Setup for Wndows 95, Wndows 98, Wndows 2000, Wndows NT, Wndows Me or Wndows XP...14 Manual Image Setup...15 Adjustng Your LCD Montor...16 User controls...16 On-screen dsplay (OSD) controls...17 Further Informaton...20 Dsplay modes...20 Power Management...21 Product Dsposal...21 Troubleshootng...22 Help and Servce Informaton...24 Specfcatons...25 Servce Informaton...26 Notces and Trademarks

4 2 í í í

5 Settng up the montor ENGLISH Product Descrpton Ths montor requres a computer wth a sutable on-board sub-system or Vdeo Adapter card that can support UXGA 1600 x 1200, SXGA 1280 x 1024, XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz. In addton to your montor, your opton package ncludes the followng: User's Gude and Installaton Fles CD Montor Safety and Warranty Informaton Manual L200p Color Montor Quck Setup Gude Power Cord L200p Color Montor Analog Interface Cable - Attached to Montor Handlng Instructons Do not support the montor wthn the screen area. The Lqud Crystal Dsplay s glass and can be damaged by rough handlng or excessve pressure. 1. Lft the montor by placng your hands where ndcated below. 2. Before usng your montor for the frst tme, remove the clear protectve flm from the front of the screen. 3

6 3. Before adjustng your montor for the frst tme, remove the lockng clp on rear of the stand. Carefully hold the screen of the montor and then squeeze at arrows shown to remove(fgure A). (Fgure A) Workplace Preparaton Ths secton gves advce on what you should consder before you set up your montor. Heght Poston the montor so that the top of the screen s slghtly below your eye level when you st at your workstaton. Orentaton - Choose a poston that gves the least reflecton from lghts and wndows, usually at a rght angle to any wndows. - Poston the montor drectly n front of you so that you do not have to twst your body to use t. - Tlt the montor to a comfortable vewng angle. 4

7 ENGLISH Adjustng the Montor Poston Wth the IBM Flat Panel Montor, you can adjust ts poston n varous ways for maxmum comfort. Vewng Angle You can tlt the screen forward and backward as shown below n Fgure A. Swvel You can swvel the screen to the left or the rght as shown below n Fgure A. Heght You can adjust heght of the screen as shown below n Fgure B. (Fgure A) (Fgure B) 5

8 Workng Practces Ths secton gves advce on how you can work comfortably and reduce fatgue. Rest Take regular breaks. Vary your posture, stand up and stretch occasonally as prolonged use of computer workstatons can be trng. Back St back n your char and use the backrest. Hands Adjust the seat heght so that your forearms are approxmately horzontal and your wrsts are straght when usng the keyboard. Your upper arms should be relaxed wth your elbows near your body. Use a lght touch on the keyboard, keepng your hands and fngers relaxed. Allow a space n front of the keyboard to rest your wrsts when not typng. Consder usng a wrstpad. Eyesght Workng wth montors, n common wth any prolonged close work, can be vsually demandng. Look away from the screen perodcally and have your eyesght checked regularly. Screen settngs Set the screen brghtness and contrast to a comfortable level. You may have to adjust these settngs as the lghtng changes durng the day. Many applcaton programs let you select color combnatons whch can help you to vew n comfort. See the User controls secton on page 16 for more nformaton. Carng for your Montor Be sure to turn off the power before you perform any mantenance on the montor. Clean your montor as follows: Gently wpe the covers and the screen wth a soft cloth. Do not use solvents or abrasves. Remove fnger marks and grease wth a damp cloth and mld detergent. Never use flammable cleanng materals to clean your IBM montor or any other electrcal apparatus. 6

9 ENGLISH Connectng your Montor Be sure to read the Safety Informaton located n the Montor Safety and Warranty Informaton Manual before carryng out ths procedure. 1. Turn off your computer and all attached devces. Next, unplug the power cord(s) to your computer and all attached devces. 2. Connect the sgnal cable. The analog sgnal cable s already connected to your montor. The analog connector s the blue connector. When connectng the analog sgnal cable (Fgure A) Connect the free end of the attached sgnal cable to the 15-pn Montor port on the computer and tghten screws. (Fgure A) If connectng a DVI-D dgtal sgnal cable (Fgure B) Connect one end of the montor sgnal cable to the whte connector on the rear panel of the montor. Connect the other end to the whte connector on the rear panel of the computer and tghten the screws. A Cable not suppled (Optonal) (Fgure B) 7

10 3. Connect the power cord to the montor and then plug the power cord nto a properly grounded outlet. Next, reconnect the power cord(s) to your computer and all attached devces. Swtchng on your Montor 1. Swtch on your computer. 2. Swtch on the montor power source by pushng the power swtch A on sde rear panel of the montor.(see Fgure B) 3. Swtch on your montor by pushng and releasng the power swtch marked [ ] at the front of the bezel. [To swtch off your montor, push and release the power swtch agan.] 4. To update or nstall devce drvers, follow the nstructons n the Devce Drver Installaton secton on page If you are usng the analog connector, run Image Setup by followng the nstructons n the Automatc Image Setup secton on page 12. 8

11 Devce Drver Installaton ENGLISH Installng the devce drver n Wndows 95 or Wndows 98 Ths secton must be completed before contnung wth the Wndows 95 or Wndows 98 Image Setup on page 12. On LCD montors, unlke CRTs, a faster refresh rate does not mprove dsplay qualty. For optmal performance, use ether 1600 x 1200 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To nstall the devce drver n Mcrosoft Wndows 95 or Wndows 98, do the followng: You must download fles from the User s Gude and Installaton Fles CD to use the Plug and Play feature n Wndows 95 or Wndows 98. Note: 1. Turn off the computer and all attached devces. 2. Ensure that the montor s connected correctly. 3. Turn on the montor and then the system unt. Allow your computer to start the Wndows 95 or Wndows 98 operatng system. Your computer s Plug and Play code mght warn you that your system hardware has changed. Ths means that t has detected your new montor for the frst tme. 4. Open the Dsplay Propertes wndow by clckng Start, Settngs, Control Panel and then double - clckng on the Dsplay con. 5. Clck the Settngs tab. If you are usng Wndows 95 : 6-1. Clck the Change Dsplay Type button. 2. Clck the Change Montor Type button. If you are usng Wndows 98 : 6-1. Clck the Advanced button. 2. Clck the Montor tab. 3. Open the Upgrade Devce Drver Wzard wndow by clckng on Change button and then select the Next button. 4. Clck Dsplay a lst of the known drvers for ths devce so that I can choose a specfc drver and then select the Next button. 7. Insert the User s Gude and Installaton Fles CD nto the CD drver and clck the Have Dsk button. 8. Clck OK. 9. Ensure that the CD drve letter s selected, and then select the DRIVERS folder. 10.Select IBM L200p montor and clck OK. The fles wll be coped from the CD to your hard dsk drve. 11.Close all open wndows and remove the CD. 12.Restart the computer. The system wll automatcally select the maxmum refresh rate and correspondng Color Matchng Profles. 9

12 Installng the devce drver n Wndows 2000 or Wndows Me Ths secton must be completed before contnung wth the Wndows 2000,Wndows Me Image Setup on page 12. On LCD montors, unlke CRTs, a faster refresh rate does not mprove dsplay qualty. For optmal performance, use ether 1600 x 1200 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To nstall the devce drver n Mcrosoft Wndows 2000 Professonal or Mcrosoft Wndows Mllennum Edton (Me), do the followng: You must download fles from the User s Gude and Installaton Fles CD to use the Plug and Play feature n Wndows 2000 or Wndows Me. Note: 1. Turn off the computer and all attached devces. 2. Ensure that the montor s connected correctly. 3. Turn on the montor and then the system unt. Allow your computer to start the Wndows 2000 or Wndows Me operatng system. 4. Open the Dsplay Propertes wndow by clckng Start, Settngs, Control Panel and then double - clckng on the Dsplay con. 5. Clck the Settngs tab. 6. Clck the Advanced button. 7. Clck the Montor tab. 8. Clck the Propertes button. 9. Clck the Drver tab. 10.Open the Upgrade Devce Drver Wzard wndow by clckng on Update Drver and then clck the Next button. 11.Select Dsplay a lst of the known drvers for ths devce so that I can choose a specfc drver and then clck the Next button. 12.Insert the Montor CD nto the CD drve and clck the Have Dsk button. 13.Clck OK. 14.Ensure that the CD drve letter s selected, and then select the DRIVERS folder. 15.Select IBM L200p montor and clck OK. The fles wll be coped from the CD to your hard dsk drve. 16.Close all open wndows and remove the CD. 17.Restart the computer. The system wll automatcally select the maxmum refresh rate and correspondng Color Matchng Profles. 10

13 ENGLISH Installng the devce drver n Wndows XP Ths secton must be completed before contnung wth the Wndows XP Image Setup on page 12. On LCD montors, unlke CRTs, a faster refresh rate does not mprove dsplay qualty. For optmal performance, use ether 1600 x 1200 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To nstall the devce drver n Wndows XP, do the followng: You must download fles from the User s Gude and Installaton Fles CD to use the Plug and Play feature n Wndows XP. Note: 1. Turn off the computer and all attached devces. 2. Ensure that the montor s connected correctly. 3. Turn on the montor and then the system unt. Allow your computer to start the Wndows XP operatng system. 4. Open the Dsplay Propertes wndow by clckng Start, Settngs, Control Panel and then double - clckng on the Dsplay con. 5. Clck the Settngs tab. 6. Clck the Advanced button. 7. Clck the Montor tab. 8. Clck the Propertes button. 9. Clck the Drver tab. 10.Open the Hardware Update Wzard wndow by clckng on Update Drver and then clck the Next button. 11.Select Install from a lst or Specfc locaton(advanced) and then clck the Next button. 12.Insert the Montor CD nto the CD drve and clck the Have Dsk button. 13.Clck OK. 14.Ensure that the CD drve letter s selected, and then select the DRIVERS folder. 15.Select IBM L200p montor and clck OK. The fles wll be coped from the CD to your hard dsk drve. 16.Close all open wndows and remove the CD. 17.Restart the computer. The system wll automatcally select the maxmum refresh rate and correspondng Color Matchng Profles. 11

14 Automatc Image Setup Image Setup Before carryng out ths secton, t s very mportant that the correct montor drvers have been nstalled.(see pages 9 and 11) The Setup Utlty ncluded on the setup CD dsplays a test pattern of dots. It does not replace or modfy the dsplay drvers. The Image Setup nstructons requre the montor to be warmed up for 15 mnutes. Ths s not requred for normal operaton. If your computer does not run wth the setup CD shpped wth the montor, refer to Manual Image Setup on page 15. The Image Setup process only apples to the current screen mode. When a new mode s selected, repeat ths secton to reset the montor. For dgtal nput, mage setup s not requred. When you frst use your montor, you must perform Auto Setup for analog nput. If you are usng dgtal nput, contnue wth the nstructons on page 6. Ths procedure sets up your montor to process the vdeo sgnals from your computer wthout mage dscoloraton or smearng. After you perform Auto Setup, the settngs are stored and used each tme you turn on the montor. In order to optmze the dsplayed mage a set-up utlty s provded on the IBM Montor CD. Operaton of ths utlty s dependent on the operatng system on your computer. You may choose to run IMAGE SETUP for each operatng system that you use. Ths means that f you sometmes use your montor whle runnng any verson of Wndows and sometmes also use t from wthn DOS (not a DOS wndow), you must run IMAGE SETUP for both Wndows and DOS. You may run versons of IMAGE SETUP n any order. Before you begn IMAGE SETUP for your computer, make sure the computer vdeo mode s set n the range of the supported screen resoluton shown n the table on page 20. You should perform IMAGE SETUP for each screen mode you use. 12

15 ENGLISH Image Setup for DOS If the montor s n standby mode (STANDBY ON), t may automatcally turn off whle you are watng for t to warm up. If ths happens, swtch off the montor and swtch t on agan after a few seconds. If you are usng PC-DOS/V, change to U.S. mode by typng CHEV US and pressng ENTER at the command prompt. The sze and dversty of the dot pattern vares wth the screen resoluton. If the screen flckers, repeat the setup several tmes untl the flcker s mnmzed, or adjust t manually by followng refer to Manual Image Setup on page 15. To set up the montor automatcally n DOS, do the followng. 1. Turn on the montor frst; then turn on the computer. If the message CHECK SIGNAL CABLE s dsplayed, or f nothng s dsplayed, check: that the vdeo nterface cable s not connected properly. the correct vdeo adapter card s not nstalled. the correct supported dsplay mode s selected for your computer. 2. Wat approxmately 15 mnutes, untl the montor warms up. 3. Insert the User's Gude and Installaton Fles CD nto the computer CD- ROM drve. 4. Dsplay the command prompt screen of the DOS full-screen dsplay. 5. Type d:\(change the drve letter to match your CD-ROM drve f t s not drve D). 6. Type TESTPATD and press ENTER. 7. Select from the screen the number for the color or text mode you want to set up. 8. Select from the screen the number for the vdeo mode you want to set up. You can repeat ths process for as many of the color and vdeo modes as you need. 9. When the dot pattern appears, press the button at the bottom of the montor. Ths actvates the AUTO SETUP procedure, whch wll optmze the dsplay settngs wth the provded dot-patterns. The screen wll momentarly turn black whle auto adjustment proceeds. 10. When fnshed, the Image Setup message dsappears and the screen returns to a normal dsplay. 11. To clear the Image Setup test pattern, press the ESC key on your keyboard. 12. Type Ext at the command prompt to return to Wndows. If you use other operatng systems, perform the approprate Auto Setup for those systems usng nstructons gven n "Image Setup Wndows 95, Wndows 98, Wndows NT,Wndows 2000, Wndows Me or Wndow XP on page

16 Image Setup for Wndows 95, Wndows 98, Wndows NT, Wndows 2000, Wndows Me or Wndows XP If the montor s n standby mode (STANDBY ON), t may automatcally turn off whle you are watng for t to warm up. To set up the montor automatcally n Wndows 95, Wndows 98, Wndows NT, Wndows 2000, Wndows Me or Wndows XP, do the followng: 1. Turn on the montor frst; then turn on the computer. The sze and dversty of the dot pattern vares wth the screen resoluton. If the message CHECK SIGNAL CABLE s dsplayed, or f nothng s dsplayed, check: that the vdeo nterface cable s not connected properly. the correct vdeo adapter card s not nstalled. the correct supported dsplay mode s selected for your computer. 2. Wat approxmately 15 mnutes, untl the montor warms up. 3. Drag the con bar and tool bar, f they are dsplayed, to the bottom of the screen. 4. Insert the User's Gude and Installaton Fles CD nto the computer CD- ROM drve. 5. Check the operatng system nstalled on your computer and follow the nstructons from the table below. Operatng system nstallaton steps Operatng System Wndows 95, Wndows 98, Wndows 2000, Wndows NT, Wndows Me or Wndows XP Step1 Select START Step2 Select RUN Step3 Type E:\TESTPAT (change the drve letter to match your CD-ROM drve f t s not drve D) and press ENTER 6. When the dot pattern appears, press the button at the bottom of the montor. Ths actvates the IMAGE SETUP procedure, whch wll optmze the dsplay settngs wth the provded dot-patterns. The screen wll momentarly turn black whle auto adjustment proceeds. 7. When fnshed, the Image Setup message dsappears and the screen returns to a normal dsplay. 8. To clear the Image Setup test pattern, press the ESC key on your keyboard. You have completed the montor setup for Wndows. If you are usng the DOS operatng system, go to Image Setup for DOS on page

17 Manual Image Setup ENGLISH If the montor s n standby mode (STANDBY ON), t mght automatcally turn off whle you are watng for t to warm up. Normally, you can complete the setup procedure usng Automatc Image Setup; however, f your screen mage s stll dstorted after you perform Image Setup or the setup CD does not run on your system, perform MANUAL IMAGE SETUP. To manually adjust the mage settng, do the followng: 1. Have your montor turned on for about 15 mnutes, untl the montor warms up. 2. Dsplay the mage you most frequently use on the screen. 3. Press the OSD Enter button at the bottom of the montor to dsplay the ntal OSD menu. 4. Use the Rght Arrow button( ) to select the IMAGE SETUP con and press the OSD Enter button to access the functon. 5. Use the Rght Arrow button( ), to select to MANUAL. Press the OK button ( )twce to select COLOK. 6. Use the Arrow buttons to manually adjust to correct (as much as possble) for jtter or nose n the mage. Press OK button( ). 7. Press OK( ) and use Arrow buttons to adjust PHASE, press OK( ). Press OK( ) agan to Save and Ext. Then press Cancel button( ) twce to ext OSD. You have completed the montor setup. 15

18 Adjustng Your LCD Montor User controls USER CONTROL FEATURES Icon Montor controls Swtches the montors on and off. Dsplay man OSD menu and selects hghlghted menu tem. and Moved the cursor to hghlght cons or make adjustments. The mage s already optmzed for many dsplay modes, however the user controls can be used to adjust the mage to your lkng. Icon Exts from current OSD menu. Drect Access Functons Brng up Brghtness adjustment. The settngs are saved after adjustment and when extng the OSD and wll be effectve thereafter. Executes automatc mage setup. CONTROLS LOCK / UNLOCK Ths feature allows you to secure the current control settngs, whle allowng the user to adjust Brghtness, so that they cannot be nadvertently changed. Push and hold the enter button[ ] for 10 seconds; the message Menu s Locked appears. You can unlock the OSD controls at any tme by pushng the enter button[ ] for 10 seconds; the message Menu s Unlocked wll appear. Swtch between nput sgnals. 16

19 ENGLISH On-screen dsplay (OSD) controls The LCD montor needs tme to become thermally stable the frst tme you turn t on each day. Thus, to acheve more accurate adjustments for parameters, allow the LCD montor to warm up (be On) for at least 15 mnutes before makng any screen adjustment. The settngs adjustable wth the user controls are vewed through the On - Screen Dsplay (OSD). Press the enter button [ ] to dsplay the man OSD menu. Intal appearance of OSD man menu; Brghtness/Contrast Ext OK sub menu; Adjustment screen; Brghtness Brghtness/Contrast 92 Brghtness: Adjusts overall screen brghtness Ext OK Ext OK OSD functons OSD Icon Descrpton sub-menu(s) Control and Adjustments Brghtness / Contrast Brghtness Contrast Adjusts brghtness Adjusts contrast Is not avalable wth a dgtal nput. Image Poston Horzontal Poston Vertcal Poston Moves the screen left and rght. Is not avalable wth a dgtal nput. Moves the screen up and down. Is not avalable wth a dgtal nput. 17

20 OSD Icon Descrpton Sub-menu(s) Controls and Adjustments Image Setup Automatc The IMAGE SETUP functon s used to adjust the level of nose n the vdeo sgnal whch causes horzontal lnes or areas on the screen where the mage appears to be unstable and jtters or shmmers. Ths can be done automatcally or manually. If AUTO s selected the mage wll automatcally adjust It s not applcable to dgtal nput. Manual If manual s selected, the user wll go to the manual adjustment screen. Clock Phase Save To adjust the focus of the dsplay. Ths tem allows you to remove any horzontal nose and clear or sharpen the mage of characters. Image Propertes Color Select the COLOR MODE you fnd most comfortable or fne tune the colors usng the CUSTOM menu, f necessary. Preset 6500K (Pnk Whte) 7200K (Normal Whte) 9300K (Blue Whte) Custom Red Increases or decreases redness Green Increases or decreases greenness Blue Save Increases or decreases blueness Scalng Ths functon dsplays the mage n ts orgnal sze or enlarged sze so as to ft n the full screen of the LCD panel. Off (1:1) On (Expand) - mage at normal sze. - mage enlarged to fll screen. 18

21 ENGLISH OSD Icon Descrpton Sub-menu(s) Controls and Adjustments Image Propertes Input Sgnal Use ths button to make the analog or dgtal connector actve. Ths feature s used when two computers are connected to the montor. The default settng s analog. Optons Informaton Dsplay the detaled nformaton of mode, model name and mcrocode. Menu Language The language chosen affects only the Englsh language of the OSD. Franças Select one of the Fve language to use for Italano the OSD. Deutsch It has no effect on any software runnng Español on the computer. Changes the poston of the OSD on the screen. Default - move at center on the screen. Menu Poston Custom Horzontal Vertcal Save Factory Default Reset should return all avalable functons (apart from language whch should not change unless adjusted va the LANGUAGE menu) to ther factory presets. Cancel Reset Accessblty Change button repeat rate and menu tme-out settng. Button repeat rate Off Default Slow - Adjusts respondence speed of button. Menu tme out - Adjusts the length of tme for whch the menu wll stay on the screen before t dsappears. Exts from current OSD menu. Ext 19

22 Further Informaton Dsplay modes If your computer has prevously been used wth a CRT montor and s currently confgured to a dsplay mode outsde the range that the Flat Panel montor can dsplay, you may need to re-attach the CRT montor temporarly untl you have reconfgured the computer, preferably to 1600 x 1200 at 60Hz. The dsplay mode the montor uses s controlled by the computer. Therefore, you should refer to your computer documentaton for detals on how to change dsplay modes. The mage sze, poston and shape may change when the dsplay mode changes. Ths s normal and the mage can be readjusted usng IMAGE SETUP and the montor controls. Unlke CRT montors, whch requre a hgh refresh rate to mnmze flcker, TFT technology s nherently flcker-free. If possble, confgure your computer for 1600 x 1200 addressablty at 60Hz vertcal refresh rate. For the dsplay modes lsted below, the screen mage has been optmzed durng manufacture. Factory Set Dsplay Modes Addressablty Refresh Rate Horzontal Frequency Note : VESA tmngs are as detaled n the VESA Dsplay Montor Tmng Specfcaton. Verson 1.0, Revson 0.8, Dated 09/17/ x Hz 31.5 khz 640 x Hz 35.0 khz 640 x Hz 37.5 khz 640 x Hz 31.5 khz 720 x Hz 31.5 khz 800 x Hz 35.2 khz 800 x Hz 37.9 khz 800 x Hz 48.1 khz 832 x Hz 49.7 khz 1024 x Hz 48.4 khz 1024 x Hz 60.0 khz 1024 x Hz 68.7 khz 1152 x Hz 68.7 khz 1152 x Hz 61.8 khz 1280 x Hz 64.0 khz 1280 x Hz 80.0 khz 1600 x Hz 75.0 khz 1600 x Hz 93.7 khz Recommended D-sub Analog only

23 ENGLISH Power Management To beneft from power management, the montor must be used n conjuncton wth a computer that mplements the Vdeo Electroncs Standards Assocaton (VESA) Dsplay Power Management Sgnalng (DPMS) Standard. The power management feature s nvoked when the computer recognzes that you have not used your mouse or keyboard for a user-defnable perod. There are several states as descrbed n the table below. As an ENERGY STAR 2000 Partner, IBM has determned that ths product meets the ENERGY STAR 2000 gudelnes for energy effcency. For optmal performance swtch off your montor at the end of each workng day, or whenever you expect to leave t unused for long perods durng the day. State Power Indcator Screen Restorng Operaton Complance On Steady green Normal Actve off Steady amber Blank Press a key or move the mouse.* ENERGY STAR 2000 * There may be a slght delay before the pcture reappears. Product Dsposal The fluorescent lamps n the lqud crystal dsplay contans a small amount of mercury. Dspose of t as requred by local ordnances and regulatons. 21

24 Troubleshootng If you have a problem settng up or usng your montor, you may be able to solve t yourself. Before callng your retaler or IBM, try the suggested actons that are approprate to your problem. Problem Possble Cause Suggested Acton Reference Screen s blank and power ndcator s off. No power to montor. Ensure that the electrcal outlet and the montor are both swtched on. Check that the power cord s frmly plugged nto the electrcal outlet and the power supply unt. If the power cord plug has a removable fuse, replace t. Try another power cord. Try another electrcal outlet. Check the power connecton at the back of the panel. Connectng your Montor secton on page 7. Screen s blank and power ndcator s steady green. Brghtness and Contrast may be too low. Adjust brghtness and contrast. User controls secton on page 17. Screen s blank and power ndcator s steady amber. The montor s n the Power Management Standby state. Press any key on the keyboard or move the mouse to restore operaton. Check the Power Management software on your computer. Press the to swtch between analog and dgtal mode. If the panel s the wrong mode for the sgnal beng provded, the montor appears to go nto sleep mode. Power Management secton on page

25 ENGLISH Problem Possble Cause Suggested Acton Reference Screen s blank and power ndcator s flashng green every 0.5 second Dsplay mode of the computer s outsde the range of the montor Reconfgure key on the computer to use a supported dsplay mode. Further Informaton secton on page 20. CHECK SIGNAL CABLE message s shown and power ndcator s steady amber. The montor s not recevng a vdeo sgnal Check that the sgnal cable s frmly connected to the computer. Check that no pns are bent n the sgnal cable connector. Connectng your montor secton on page 7. For mage problems, you may want to run IMAGE SETUP agan before consultng to ths secton. In most cases, IMAGE SETUP can fx the problems. See Autometc Image Setup for the computer on page 12 for detals. Image appears to be smeared Image appears to be dscolored A few dots are mssng, dscolored, or napproprately lghted. There are noses n the vdeo sgnal The color settng may be ncorrect. Select IMAGE SETUP menu n the OSD. Then select MANUAL to adjust CLOCK / PHASE settngs. Adjust the Color settngs. User Controls secton on page 18. User Controls secton on page 18. A small number of mssng, dscolored, or lghted dots may be present on the screen, whch s an ntrnsc characterstc of the TFT LCD technology and s not an LCD defect. 23

26 Help and Servce Informaton If you are unable to correct the problem yourself, you may seek further help as follows: If possble, stay by your computer. Your Techncal Support Representatve may wsh to go through the problem wth you durng the call. More help, late-breakng news and detals of the latest accessores for these products may be found on the worldwde web at: accessores Call the IBM HelpCenter. In the U.S.A and Puerto Rco call In Canada(Toronto Only) call In Canada(all other) call In other countres contact your dealer, retaler, or other IBM authorzed Servcer. Before callng, please have avalable as much of the followng nformaton as possble: 1. Model and seral number from the label on your montor. 2. Purchase recept. 3. Descrpton of problem. 4. Computer type and model. 5. System confguraton (hardware ftted, etc.). 6. System BIOS verson number. 7. Operatng System and verson number. 8. Dsplay drver verson number. 9. Vdeo Adapter Type. 24

27 Specfcatons Power consumpton fgures are for the montor and the power supply combned. Ths color montor (Type-model 6736-HB0) uses a 20.1-nch TFT LCD. H W D Heght: mm (15.42 nch) - Mn mm (18.57 nch) - Max Wdth: mm (18.41 nch) Depth: mm (10.2 nch) ENGLISH Weght Image Power Input Power Consumpton Vdeo Input Sync Input Communcatons Supported Dsplay Modes Wth Stand: Vewable Image Sze: Maxmum Heght: Maxmum Wdth: Pxel Ptch: Supply Voltage: Rated Current: Normal Operaton: Actve off: Off: Input Sgnal: Horz. Addressablty: Vert. Addressablty: Clock Frequency: Type VESA DDC: Standard modes : Horz. Frequency: Vert. Frequency: 8.35 kg (18.41 lbs) 20.1-nch ( mm) 306 mm(12.05 nch) 408 mm(16.04 nch) mm (H) x mm (V) V ac 60/50 ± 3Hz 1.2A < 65 W < 3 W < 1 W Analog-75 ohm 0.7V Dgtal-DVI pxels (max) 1200 lnes (max) 130 MHz (Dgtal) 205 MHz(Analog) Analog - Separate, Composte, SOG Dgtal-DVI 1.0 E-DDC IBM, VESA, MAC Dgtal: khz Analog: khz 56-85Hz Envronment Temperature: Operatng: Storage: Shppng: Humdty: Operatng: Storage: Shppng: 10 to 35 C (50 to 95 F) - 20 to 60 C (-4 to 140 F) - 20 to 60 C (-4 to 140 F) 10 to 80% 5 to 95% 5 to 95% 25

28 Servce Informaton The followng parts are for use by IBM servce, or IBM authorzed dealers, to support the customer warranty. Parts are for servce use only. Model Type 6736 Descrpton Vdeo Color MTM 31P9263 FRU Montor Hybrd SB 6736-HB0 31P9264 FRU Stand Hybrd SB 6736-HB0 31P9265 FRU Vdeo Cable Analog Black 6736-HB0 26

29 Notces and Trademarks ENGLISH Ths secton contans nformaton on notces and trademarks. Notces IBM may not offer the products, servces, or feature dscussed n ths document n all countres. Consult your local IBM representatve for nformaton on the products and servces currently avalable n your area. Any reference to an IBM product, program, or servce s not ntended to state or mply that only that IBM product, program, or servce may be used. Any functonally equvalent product, program, or servce that does not nfrnge any IBM ntellectual property rght may be used nstead. However, t s the user's responsblty to evaluate and verfy the operaton of any non-ibm product, program, or servce. IBM may have patents or pendng patent applcatons coverng subject matter descrbed n ths document. The furnshng of ths document does not gve you any lcense to these patents. You can send lcense nqures, n wrtng, to: IBM Drector of Lcensng IBM Corporaton North Castle Drve Armonk, NY U.S.A The followng paragraph does not apply to the Unted Kngdom or any country where such provsons are nconsstent wth local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON- INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow dsclamer of express or mpled warrantes n certan transactons, therefore, ths statement may not apply to you. Ths nformaton could nclude techncal naccuraces or typographcal errors. Changes are perodcally made to the nformaton heren; these changes wll be ncorporated n new edtons of the publcaton. IBM may maker mprovements and/or changes n the product(s) and/or the program(s) descrbed n ths publcaton at any tme wthout notce. IBM may use or dstrbute any for the nformaton you supply n any way t beleves approprate wthout ncurrng any oblgaton to you. Any references n ths publcaton to non-ibm Web stes are provded for convenence only and do not n any manner serve as an endorsement of those Web stes. The materals at those Web stes are not part of the materals for ths IBM product, and use of those Web stes s at your own rsk. 27

30 Trademarks The followng terms, used n ths publcaton, are trademarks or servce marks of the IBM Corporaton n the Unted States, other countres, or both; HelpCenter IBM ENERGY STAR s a U.S Govt. regstered trademark. Mcrosoft Wndows, and Wndows NT are trademarks of Mcrosoft Corporaton n the Unted States, other countres, of both. Other company, product, and servce names may be trademarks or servce marks of other. Copyrght Internatonal Busness Machnes Corporaton All rghts reserved. 28