High intensity led illuminator ILED42A FEATURES: DESCRIPTION: ELECTRICAL CHARACTERISTICS:

Size: px

Start display at page:

Download "High intensity led illuminator ILED42A FEATURES: DESCRIPTION: ELECTRICAL CHARACTERISTICS:"

Alyson Simmons
5 years ago
Views:

1 High intensity led illuminator May 2010 Rev 0.3 ILED42A FEATURES: High luminous flux Low cost Fully protected Wide input voltage range Available with different led colours and lenses DESCRIPTION: The IDP ILED42A is a low cost fully protected eight-leds illuminator. The IDP ILED42A is protected for short circuit, polarity inversion, over voltage and over temperature. The user can vary the light intensity simply modifying the voltage applied to the illuminator. When the voltage applied exceed 13.5V leds are switched off (but in any case the input voltage must never exceed 40V). The dc voltage power supply is provided through an external male panel connector. A cable is provided with a female plug (the cable length is user defined between 1 meter to 10 meters on request: see Tab3). The device can be equipped without lenses or with lenses (10, 20 or 40 ) and with different led colours: see Tab2 for details. ELECTRICAL CHARACTERISTICS: The power supply voltage for the IDP- ILED42A is between 0V to 13.5V. The light intensity is directly modulated through the applied voltage. PARAMETER Min Typ Max NOTE Input voltage range 0V V Never exceed 40V Input power 8.5W 8.9W 10W Typ 13V Tab1: Table of Electrical Characteristics. Indep Electronics & Photonics

2 When voltage exceed 13.5V, an auto switch off is executed to protect led diodes. The absolute maximum input voltage is 40V (never exceed this voltage). OPTICAL CHARACTERISTICS: Viewing angle (no lenses) FWHM 130 Order Code: L-130 Viewing angle (with lenses) FWHM 10, 20, 40 Order Codes: L-10, L-20, L-40 Pure White Order Code: C-PW Colour Temperature 6500 K (typ) - Luminous Flux (max) 640lm (typ) Total for 8 leds Illuminance (max) 20000lux (typ) On lenses 20 Natural White Order Code: C-NW Colour Temperature 4000 K (typ) - Warm White Order Code: C-WW Colour Temperature 3000 K (typ) - Royal blue Order Code: C-RB Dominant wavelength 457nm (typ) - Blue Order Code: C-B Dominant wavelength 465nm (typ) - Green Order Code: C-G Dominant wavelength 525nm (typ) - Amber Order Code: C-A Dominant wavelength 590nm (typ) - Red Order Code: C-R Dominant wavelength 625nm (typ) - Tab2: Table of Optical Characteristics. Indep Electronics & Photonics

3 CONTROL PANEL: In the lateral panel there is the power connector. In the power connector only pin1 and pin2 are used. The light intensity can vary from 100% to 0% modifying the dc voltage power supply. Fig1: Lateral Panel. CABLE DESCRIPTION: Cable can be provided in different length see Tab3. The cable has four wires: two wires for power supply and Cable Length Wire section Order Code 1 mt 0.22mm 2 W-01 3 mt 0.22mm 2 W-03 5 mt 0.22mm 2 W-05 7 mt 0.22mm 2 W mt 0.22mm 2 W-10 Tab3: Table of cable length. other two wires not connected (see Tab4 for details). Cable pin Colour NOTE 1 Blue 0V power 2 Red 0V to 13.5V 3 Yellow NC 4 Green NC Tab4: Table of cable wires. MECHANICAL DIMENSIONS: Mechanical dimensions are in fig2 (all dimensions are in millimetres). The drawing is not in scale. The weight is approximately 290g. All the structure is grey anodized aluminium except the lateral frames (black plastic) and the front transparent plexiglass (PMMA). Indep Electronics & Photonics

4 Fig2: Mechanical dimensions. ENVIRONMENTAL CONDITIONS: Operating Temperature Storage Temperature Protection -10 C to +40 C -20 C to +85 C IP50 (IP64 on request) Tab5: Environmental Conditions. If IP64 protection is requested, the cable and the panel connectors are slightly different: see Fig3. When connectors are plugged together the total length is 40.6mm. Order code for protection is IP-50 or IP-64. Fig3: IP64 Connectors. Indep Electronics & Photonics

5 ORDER CODE: An example of order code for an IDP-ILED42A illuminator with 20 lenses, pure white leds (6500 K) with 3 meters cable length and IP50 protection: IDP- ILED42A L-20 C-PW W-03 IP-50 If not specify the default illuminator protection is IP50. Indep Electronics & Photonics

6 This Datasheet has been compiled to provide an overview of the device available from INDEP SRL. For more information directly contact INDEP SRL. Specifications are subject to change without notice. Information furnished herein is believed to be accurate and reliable. However The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of INDEP SRL are granted by the Company in connection with the sale of INDEP products, expressly or by implication. INDEP s products are not authorized for use as critical components in life support devices or systems. Product names mentioned in this product overview may also be trademarks used here for identification purposes only. INDEP SRL. All rights reserved. Indep Electronics & Photonics

SURFACE MOUNT LED LAMP FULL COLOR 1210

SURFACE MOUNT LED LAMP FULL COLOR 1210 PACKAGE DIMENSIONS 2 1 Top View.6 (1.5) G B R.17 (2.7) 3 4.127 (3.2) COMMON ANODE Side View RESIN.198 (.5).43 (1.1) Bottom View PCB.473 (1.2) ANODE SIDE.276 (.7) Pin 4 Die 1 Pin 1 (Red) Die 2 Pin 2 (Green)