INSTALLATION AND OPERATION M
|
|
- Gabriel Haynes
- 5 years ago
- Views:
Transcription
1 INSTALLATION AND OPERATION M RUBYSTAR INSTALLATION AND OPERATION MANUAL Safety Instructions : Only authorised installers should install and or replace Rubystar inverters. Ensure that all electrical installations are in accordance with local electrical requirements and codes before installation can commence. Pay specific attention to earthing. Before installation or usage of the Rubystar inverter, please read all instructions and cautionary markings in the technical documents,rubystar inverter system and the PV-array. Do NOT disconnect the PV module from the Rubystar inverter without first switching the inverter to the manual AC override position ( See controller settings ). Do NOT attempt to repair the Rubystar inverter. If it fails, contact Rubystar Customer Support to obtain a reference number and start the replacement process. Damaging or opening the Rubystar inverter will void the warranty. Rubystar inverter system introduction : Photovoltaic panels capture the sun s energy and generate electrical DC current. The DC current is inverted through the intelligent Rubystar unit to AC current which is fed to the conventional resistance element in the geyser. This results in electrical savings and the heating of water in the geyser. Rubystar inverter installation procedure : STEP 1 1. Switch off AC power supply of the geyser on the DB Board and the isolator switch. 2. Drain the geyser to fit the new element which has been supplied as part of the installation kit. In the case of a new installation make sure the element is the correct wattage. 3. Fit the new element 4. Do not secure the flange cover at this stage 5. Refill the geyser with water and check for water leaks on the flange STEP 2 1. Mount the PV panels on the roof as per the manufacturer s instructions and earth the frame. 2. Follow the attached diagram and connect points B,C and D. Do NOT connect points A and E at this stage. 3. Space and mount the inverter between the geyser and the isolator according to the available cable length. Use the available holes at the top of the inverter to affix the unit with screws. 4. Remove the thermostat from the geyser and insert the Micro Sensor in the thermostat pocket. Once inserted, insert the thermostat back into the same pocket. Please note: if the unit is supplied with a conventional temprature probe secure the probe to the geyser flange. 5. Connect the Black AC cable of the inverter, marked GEYSER to the AC element and ensure that the earth is properly secured. 6. Connect the White AC cable of the inverter, marked ISOLATOR to the Isolator switch and ensure that the earth is properly secured. 7. Mount the display inside the house in an easily accessible position for the client. 8. Secure the display cable neatly and connect the cable to the ethernet port on the inverter.
2 9. At the inverter crimp the positive MC4 connector to the red cable. Crimp the negative MC4 connector to the black cable. 10. Connect points A & E as per instruction at STEP 2 point number At the inverter, do a polarity test. The red cable must test positive and the black cable must test negative. 12. Connect the MC4 connectors to the inverter, first the black (negative) and then the red (positive) 13. Switch on the power at the DB board first and then at the isolator switch. 14. Use the manual override switch on the Display to activate the AC power to the element. 15. Use your multi-meter and measure the voltage at the geyser terminals of the element. Mains voltage (220VAC /230VAC) should be present. 16. Use the manual overide switch on the display to de-activate the AC power to the element. 17. Please note that AC power may still be present. 18. Measure the Voltage at the element with the meter set to AC voltage. An AC voltage reading between 50V and 160V should be measured during day light. 19. Fit and secure the geyser flange cover. 20. At the display, disconnect the override function and set the controller as per the instruction manual. Troubleshooting sugestions : 1. Check the connection to the load resistance. Never disconnect the DC wires while the inverter is producing power. Re-connect the DC module connectors and watch for the display to activate. 2. Make sure the Isolator is functioning properly. 3. Verify the power resistance from the element. 4. Check the DC connections between the inverter and the PV module. 5. If the problem persists, please contact Rubystar 6. Do not attempt to repair the Rubystar inverter. If troubleshooting methods fail, please follow the warranty procedures. Un-installing a Rubystar inverter: 1. Press inverter Bypass switch on the display. ( see Display diagram) 2. Disconnect DC positive at inverter. 3. Disconect DC negative at inverter. 4. Switch of geyser at DB board. 5. Switch off geyser at isolator. Note: use a multi meter to ensure that there is no AC present at the isolator or geyser. 6. Disconnect AC at isolator. 7. Disconnect AC at geyser. 8. Remove temperature probe from geyser flange ( in the case of a micro sensor, remove from thermostat pocket. 9. It is now safe to remove the inverter. Note : Make sure all components and cables are included when returning the unit. 10. Do not damage any components or cut any cables as this will void your warranty.
3 Technical data : Nominal DC Power Maximum Open Voltage Maximum DC Current AC Input Voltage System start-up voltage PV Array ( 100L 200L / 2KW 3KW Enclosure Dimensions (h x w x l) & Weight Rubystar Inverter Dimensions (h x w x l) & Weight Controller 600W / 1320W 210 V 8.5 A 220 V 100 V 600W / 1320W IP55 205x155x70 / 1.5 kg 120x60x20 / 0.1 kg Controller settings : Buttons from left to right: A = Select B = UP C = DOWN D = MANUAL on and off for Mains Override 230VAC to the geyser. E = Emergency Inverter Bypass When power is ON one should read the time that was previously selected on the unit. The status of the 230VAC power to the geyser may be On or Off and is displayed to the right side of the time displayed on the screen. Pressing and holding Select will scroll through the various parameters that can be adjusted. Press and Hold select, Scroll to RESET (10) and press UP (B) before adjusting any settings.
4 Setting the time of day: Press and hold Select until TIME-hrs is displayed.use UP and DOWN to enter correct hour of day. Press Select again, (this will also save the hour entry) until TIME-min is displayed Use UP and DOWN to enter correct minute of day. Adjusting the times that the geyser must be switched to 230VAC power for the morning plus evening periods: Press select and keep in to scroll until ON1-hrs (1) is displayed and use UP and DOWN to set the required ON time for the geyser. Press Select to display OFF1-hrs (2)and select the required off time for the geyser. Press select and keep in to scroll until ON2-hrs (3) is displayed and use UP and DOWN to set the required ON time for the geyser. Press Select to display OFF2-hrs (4) and select the required off time for the geyser. Press select and keep in to scroll until Temprature Lo (Low) (5) is displayed, use UP and DOWN to select 0. Press select and keep in to scroll until Temprature Hi (High) (6) is displayed, use UP and DOWN to select 65. Note: When maximum temperature setting is reached the thermostat will switch off the geyser.
5 Manual Override: Note : By pressing the MANUAL (RED) button to the On state, the geyser will be powered via Mains supply. Pressing it again will revert to normal (PV/Mains) operation, showing off. With temprature Lo (Low) and Hi (High) set to 0 and 65 will result in maximum effiency. Warranty registration : Visit our website, and complete the online warranty activation registration document to activate the warranty of your Rubystar inverter. Failure to activate your warranty within 30 Days from installation date will void the warranty on your Rubystar inverter.
POET-1 P.O.E. TEST PORT MEASUREMENT TOOL INSTRUCTION BOOK
POET-1 P.O.E. TEST PORT MEASUREMENT TOOL INSTRUCTION BOOK IB6386-01 9-1-2015 TABLE OF CONTENTS DESCRIPTION 2 HOW TO CABLE THE POET-1 2 HOW TO TAKE A MEASUREMENT 3 EASE OF USE 3 APPLICATIONS 3 CARE AND
More informationenglish SGC inverter series hf transformer input voltage up to 800 V touch screen built-in data loggers
english SGC inverter series hf transformer input voltage up to 800 V touch screen built-in data loggers SGC inverters: the best choice advanced technology SGC inverters feature advanced design and superior
More informationPRELIMINARY Sunny Boy 240-US
PRELIMINARY Sunny Boy 240-US SB 240-US-10 Optimized reliability Simple installation Unrivaled monitoring SMA-backed security Multigate technology allows for reduced component count Private band powerline
More informationSY-MS121 SY-MS121-AP
Installation Guide SY-MS121 and SY-MS121-AP Presentation Switcher with Multi-Format Inputs and Outputs 4 HDMI, 4 VGA, 1 Component video, 2 Composite video & 1 S-video inputs Simultaneous HDMI, VGA & HDBaseT
More informationModel /29S RF Splitter
Instruction Manual Model 1584-29/29S RF Splitter March 2013, Rev. 0 LNB VOLTAGE A B MODEL 1584 COMBINER CROSS TECHNOLOGIES INC. GND+DC ON Data, drawings, and other material contained herein are proprietary
More informationInstallation Operation Maintenance
Installation Operation Maintenance Rooftop Energy Recovery Module for TKD / TKH / WKD / WKH YKD / YKH / DKD / DKH # 125-155-175-200 250 265-290-340 # 275-300-350-400-500-600 April 2011 RT-SVX42B-E4 General
More informationSafety Information. Camera System. If you back up while looking only at the monitor, you may cause damage or injury. Always back up slowly.
Table of Contents Introduction...3 Safety Information...4-6 Before Beginning Installation...7 Installation Guide...8 Wiring Camera & Monitor...9-10 Replacement Installation Diagram...11 Clip-On Installation
More information4 Wiring Brochure Wiring and installation of specific control
- Wiring Brochure tekmarnet 4 User Switch 480 W 480 09/09 1 Information Brochure Choose controls to match application 2 Application Brochure Design your mechanical applications 3 Rough In Wiring Rough-in
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual REV
REV. 1.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationMT03A Electronic converter for flow rate transmitters
Instructions manual MT03A Electronic converter for flow rate transmitters The art of measuring R-MI-MT03A Rev.: 0 English version PREFACE Thank you for choosing a Tecfluid S.A product. This instruction
More informationHDBaseT Extender Set 100m User Guide
HDBaseT Extender Set 100m User Guide Model CM-BT10-TXRX100 Last modified: 09/29/16 Doc ID - 620 Rev 04 Copyright Trademarks and patents Manufacturer Contact information 29SEP16 Clare Controls, LLC. All
More informationInstallation and User Guide 458/CTR8 8-Channel Ballast Controller Module
Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Helvar Data is subject to change without notice. www.helvar.com i Contents Section Page Introduction 1 Installation 2 1. Attach
More informationField Service Procedure Replacement GACP Control Panel Kit, ST24
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the Graphic Antenna Control Panel (GACP) for the ST24 antenna. 2. Checklist: Verify Power to the GACP Verify Communications
More informationElectronic converter for level transmitters MT03L Instructions manual
Electronic converter for level transmitters MT03L Instructions manual R-MI-MT03L Rev.: 1 English version PREFACE Thank you for choosing the MT03L converter from MT03 series of Tecfluid S.A. This instruction
More informationOTX Optical Transmitter. Operation Instructions
OTX 1310-10 Optical Transmitter Operation Instructions Operation Instructions OTX 1310-10 Optical Transmitter Table of contents 1. Description...4 1.1. Block Diagram...4 2. Front and rear panel...5 2.1.
More informationPanel-mounting thermostats, type series EM
Data sheet 602025 Page /5 Panel-mounting thermostats, type series EM Particularities Operating temperature limiter Limit value range up to +650 C with temperature compensation Brief description Panel-mounting
More informationapple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema HD Display 23" LCD (ADC) 2003 Apple
More informationEZCOM-1. PLC - to - AMS MESSAGE DISPLAY INTERFACE INSTALLATION AND OPERATING INSTRUCTIONS. Rev March, 2001
EZCOM-1 PLC - to - AMS MESSAGE DISPLAY INTERFACE INSTALLATION AND OPERATING INSTRUCTIONS Rev 1.3 - March, 2001 CONTENTS Page INTRODUCTION 1 SPECIFICATIONS 1 LIST OF SUPPLIED ITEMS 1 INSTALLATION & TESTING
More informationNoise Detector ND-1 Operating Manual
Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation
More informationHeating thermostat Series AMHs B Operating Instructions 11.06/
Heating thermostat Series AMHs-1-80 B 60.3045.0 Operating Instructions 11.06/ 00367556 Typographical conventions Warning signs The signs for Danger and Warning are used in this manual under the following
More informationDLP200M 2 Relay Module for Heating and Cooling Plants
Product Sheet TH6.24 Thermostat Type DLP200M DLP200M 2 Relay Module for Heating and Cooling Plants The DLP 200 M is a relay module for activation of loads (namely thermal actuators or circulators) in wireless
More informationGRANT RF CONTROL CENTER INSTALLATION INSTRUCTIONS Always disconnect battery while servicing or modifying the electrical system of the vehicle.
GRANT RF CONTROL CENTER INSTALLATION INSTRUCTIONS Always disconnect battery while servicing or modifying the electrical system of the vehicle. You will need standard hand tools, a Test Light and a Digital
More informationTDDFM14 OWNER S MANUAL
TDDFM14 OWNER S MANUAL Table of Contents 3 Installation Features System Selector Switches 6 10 Connecting Wires and Mounting Thermostat 10 Operation (Programming) Programming/Setting Clock Personal Program
More information263 Series LED Bargraph Indicator and Controllers
263 Series LED Bargraph Process Control Water Treatment High resolution 51 segment LED Bargraph for easy reading Accuracy 1% Red display Vertical or Horizontal mounting & stackable Connection Diagrams
More informationapple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber Apple Computer, Inc. All rights reserved.
apple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber 2004 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Studio Display 17" LCD (ADC) 2003 Apple
More informationPLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator
3.635.5275.254 IM-P486-18 CH Issue 3 PLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator Installation, Start-up and Operation Manual 1. Safety information 2. General product information
More informationINSTALLATION & USER GUIDE
INSTALLATION & USER GUIDE Digidim 458 8-Channel Dimmer STEP 1 Assemble Dimmer Unit STEP 2 Mount Dimmer Chassis STEP 3 Electrical Installation STEP 4 Attach Module and Make Connections STEP 5 Replace Cover
More informationOTFOA-25XX SERIES ERBIUM-DOPED FIBER AMPLIFIER (EDFA)
OTFOA-25XX SERIES ERBIUM-DOPED FIBER AMPLIFIER (EDFA) With Mid-stage Access Operating Manual TEL: (209) 586-1022 USA: (800) 545-1022 FAX: (209) 586-1026 E-Mail: salessupport@olsontech.com www.olsontech.com
More informationSY-HDBT-SLIM-100S Extender Set
Installation Guide SY-HDBT-SLIM-100S Extender Set with HDMI, Ethernet, IR, RS232 and Power over 100m of cat6 Cable HDBaseT HDMI Extenders SY Electronics Ltd, Unit 7, Worrall Street, Salford, Greater Manchester,
More informationWhat is SnoCam? SnoCam Installation Guide. SolarVu
4 1 2 3 4 5 6 7 8 D+ Rx- GND V+ GND V+ Power 1 2 3 4 5 6 7 8 9 10 What is? SolarVu Installation Guide SolarVu is an energy portal that enables remote monitoring of renewable energy generation sites over
More informationSY-HDBT-100 Extender Set
Installation Guide SY-HDBT-100 Extender Set with HDMI, IR, RS232 and Ethernet over 100m of cat6 Cable HDBaseT HDMI Extenders SY Electronics Ltd, Unit 7, Worrall Street, Salford, Greater Manchester, M5
More informationPLEASE READ THIS PRODUCT MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
Features The AVG-HD400 is an HDBT 2.0 transceiver set which contains a transmitter and a receiver. Compliant with HDMI 1.4 & HDCP 2.2, it is able to transmit high-definition signals up to 4Kx2K@60Hz. The
More informationUSERS MANUAL GR ONE 300 GR ONE 700 GR ONE 1400
USERS MANUAL GR ONE 300 GR ONE 700 GR ONE 1400 PURE SOUND USER MANUAL PURPOSE This user manual is dedicated to the use of the bass amplifiers GR-ONE 700, GR-ONE700x2 and GR-ONE 300. The manual includes
More informationThank you for purchasing this product. If installing for someone else, please ensure that the instructions are handed to the householder.
Instruction Manual TPSE201 (181422) - BOSS TM Universal Programmer TPSE101 (569565) - BOSS TM Universal Timeswitch Thank you for purchasing this product. If installing for someone else, please ensure that
More informationT775L Series 2000 Electronic Stand-Alone Staging Controller
T775L Series 2000 Electronic Stand-Alone Staging Controller INSTALLATION INSTRUCTIONS PRODUCT DESCRIPTION The T775 electronic stand-alone controllers are the next generation of commercial and agricultural
More informationInstruction Manual. 2.4G Digital Wireless Four Channel Transmitter System RVS-554W. Reverse With Confidence 1
Instruction Manual 2.4G Digital Wireless Four Channel Transmitter System RVS-554W 1 NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation
More informationLED Backlight for Technics amplifiers
LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to
More informationLED Driver Linear / area fixed output
Driver LC 10W 350mA fixc lp SNC2 ESSENCE series Product description Fixed output built-in LED Driver Constant current LED Driver Output current 350 ma Max. output power 10.2 W Up to 80 % efficiency For
More informationArc Detector for Remote Detection of Dangerous Arcs on the DC Side of PV Plants
1 Arc Detector for Remote Detection of Dangerous Arcs on the DC Side of PV Plants Heinrich Haeberlin Berne University of Applied Sciences (BFH-TI), Division of Electrical- and Communication Engineering,
More informationMONITOR POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2099-10xx 10MHz Frequency Source April 2014, Rev. H MENU INTERNAL LEVEL = +10dBm MONITOR POWER 1 2 MODEL 2099 FREQUENCY SOURCE CROSS TECHNOLOGIES INC. ALARM OVEN REMOTE EXECUTE
More informationDLP600M 6+1 Relay Module for Heating and Cooling Plants
Product Sheet TH6.25 Thermostat Type DLP600M DLP600M 6+1 Relay Module for Heating and Cooling Plants The DLP 600 M is a relay module for activation of loads (namely thermal actuators or circulators) in
More information7 Day Digital Programmer 3 Channel Surface Mount
7 Day Digital Programmer 3 Channel Surface Mount Model: TRT038N Installation & Operating Instructions 1. General Information These instructions should be read carefully and retained for further reference
More informationINTRODUCTION TERMINAL LAYOUTS FX2N-4AD-TC SPECIAL FUNCTION BLOCK USER S GUIDE
FX2N-4AD-TC SPECIAL FUNCTION BLOCK USER S GUIDE JY992D65501A This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N-4AD-TC
More informationUSER S GUIDE. 1 Description PROGRAMMABLE 3-RELAY LOGIC MODULE
1 Description The is a programmable 3 relay logic module that may be used for multiple applications, including simple timing, door mounted sensor inhibiting and advanced relay sequencing. The contains
More informationMS2540 Current Loop Receiver with RS485 Communication
MS2540 Current Loop Receiver with RS485 Communication User Manual Metal Samples Company A Division of Alabama Specialty Products, Inc. 152 Metal Samples Rd., Munford, AL 36268 Phone: (256) 358 4202 Fax:
More informationMAXTECH, Inc. BRC-1000 Series. C-Band Redundant LNB Systems. Technology for Communications. System Block Diagrams
MAXTECH, Inc. Technology for Communications BRC-1000 Series C-Band Redundant LNB Systems Introduction Redundant LNB systems minimize system downtime due to LNB failure by providing a spare LNB and an automatic
More informationUser Manual RTHDBT402PT & RTHDBT402PR
User Manual RTHDBT402PT & RTHDBT402PR REVTEK HDMI/IR/RS232 Twisted Pair Extender HDBaseT with POE Page 1 All Rights Reserved Version: RTHDBT402P 2013V1.0 NOTICE: Please read this user manual carefully
More informationNAVIGATOR OWNER S MANUAL
OWNER S MANUAL UNCHARTED WATERS, NEW HORIZONS Making shapes spin and move is notoriously difficult for pattern synthesis based only on oscillators synchronized to horizontal and vertical frequency ranges.
More informationMAXX BOX. MX102/202 Series. MAXX Box
MX102/202 Series MAXX Box MAXX BOX 1 C O N T E N T S SECTION 1: OVERVIEW... 4 Introduction... 4 Description... 4 Ordering Information... 4 Specifications... 5 Environmental... 5 Electrical... 5 Physical...
More informationRD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011
RD - 122 RACK MOUNT DIMMER OWNERS MANUAL VERSION 1.3 03/09/2011 Page 2 of 14 TABLE OF CONTENTS UNIT DESCRIPTION AND FUNCTIONS 3 POWER REQUIREMENTS 3 INSTALLATION 3 PLACEMENT 3 POWER CONNECTIONS 3 OUTPUT
More informationTRANSCENSION 6-CHANNEL DMX DIMMER PACK (order code: BOTE40) USER MANUAL
www.prolight.co.uk TRANSCENSION 6-CHANNEL PACK (order code: BOTE40) USER MANUAL SAFETY WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this
More informationTroubleshooting CS800/LC900 Bikes
Troubleshooting CS800/LC900 Bikes CS800/900LC Bike Troubleshooting Entering the Maintenance Mode 15 Touch Screen: The Maintenance Mode is designed to help the tech determine certain faults in the upper
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS 1. Read, follow and keep these instructions safely. 2. Heed all warnings. 1. Do not use this apparatus near water. 2. Clean only with dry cloth. 3. Do not block any ventilation
More informationUser Guide. TMDS 5x C Digital SCR Multiswitch for SkyQ. Version B Date 02/2016 EN TMDS 54 C TMDS 58 C
User Guide TMDS 5x C Digital SCR Multiswitch for SkyQ Model Item no. TMDS 54 C 307370 TMDS 58 C 307378 Version 891601B Date 02/2016 Attention! Failure to comply with the specified precautionary measures
More informationDigital Time Switch. Installation & Operating Instructions
Digital Time Switch Model: NTT06 24 Hour General Purpose Digital Timer Model: NTT07 7 Day General Purpose Digital Timer Installation & Operating Instructions 1 1. General Information These instructions
More informationTech Support: Customer Service: General Tech Questions: Tech Docs:
Tech Support: 1-800-407-4545 Customer Service: 1-800-523-2462 General Tech Questions: Tech_Services@beainc.com Tech Docs: www.beasensors.com BR3-X Programmable 3 Relay Advanced Logic Module & Restroom
More informationCC2000 SERIES SYSTEM CLOCKS / DISPLAYS
FN:CC2KMAN1.DOC CC2000 SERIES SYSTEM CLOCKS / DISPLAYS DESCRIPTION CC2000 Series System Clocks provide an economical solution for any size clock system. They are easily corrected by master clock systems
More informationInstallation Manual SaVi Note Underwater LED Light
Installation Manual SaVi Note Underwater LED Light Model Numbers SAVI-NOTE7, SAVI-NOTE0 Table of Contents Safety Precautions...2 SaVi Note Install Instructions...3- M Instructions...- Warnings READ AND
More informationInstallation Guide. Cellular Plug-in for Inverters with SetApp. Version 1.1
Installation Guide Cellular Plug-in for Inverters with SetApp Version 1.1 2 Version History Version 1.0 (initial release)- January 2019 Version 1.1- January 2019 Modified Technical Specifications modem
More informationProvides an activation of Relay 1 triggered by Input 1. The function also provides an option for reverse-logic on the activation of Input 1.
USER S GUIDE PROGRAMMABLE 3-RELAY LOGIC MODULE 1 Description The is a programmable 3 relay logic module that may be used for multiple applications, including simple timing, door mounted sensor inhibiting
More informationDigital Economy Seven Programmer
Digital Economy Seven Programmer Model: TRTD7N White Installation & Operating Instructions 1. General Information These instructions should be read carefully and retained for further reference and maintenance.
More informationSCALE & WEIGHT DISPLAYS
The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters
More informationCR-6 MIXER USER MANUAL ENGLISH. Order Code: MIXE01
CR-6 MIXER P R O F E S S I O N A L 1 9 R A C K M I X E R Order Code: MIXE01 w w w. p r o l i g h t. c o. u k USER MANUAL ENGLISH WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE
More informationGetting started with
PART NO. CMA11 3 MADE IN CHINA 1. Measuring CAT II 2. Max. voltage 250V ~ 3. Max. current 71 Amp Getting started with Electricity consumption & Solar PV generation monitoring single phase, for homes fitted
More information2002, Cisco Systems, Inc. All rights reserved.
2002, Cisco Systems, Inc. All rights reserved. 1 Panduit Network Infrastructure Essentials Chapter 8 Tools of the Trade Learning Objectives Learn about common tools used in the telecommunications cabling
More informationSpectra Batten (Order code: LEDJ95)
www.prolight.co.uk Spectra Batten (Order code: LEDJ95) Safety WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this equipment away from rain,
More informationQuick Operation Guide of LTN7700/7600 Series NVR
Quick Operation Guide of LTN7700/7600 Series NVR UD.6L0202B0042A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable
More informationSONARtrac Technical Bulletin
Page 1 of 14 Purpose: The purpose of this document is to formally release the SONARtrac TM Troubleshooting. The guide lists problems that may be encountered by personnel installing SONARtrac TM meters
More informationSunny Boy 700U SOLARTECHNOLOGY. Installation Guide. Photovoltaic, Grid-Tied String Inverter
Sunny Boy 700U Photovoltaic, Grid-Tied String Inverter SOLARTECHNOLOGY Installation Guide Installation Guide Copyright 2003 SMA America, Inc. All rights reserved. No part of this document may be reproduced,
More informationOperation Manual VMS 3.0 Video System
Operation Manual VMS 3.0 Video System for the AlterG Anti-Gravity Treadmill 1 This manual covers operation procedures for the following AlterG products: AlterG Video System model VMS 3.0 NOTE: The following
More informationOPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION INSTALLATION
OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION The Psidex Audio Laboratory PGP- 1A is a vacuum tube based microphone preamp and program line amplifier designed to provide solid, robust
More informationKu-Band Redundant LNB Systems. 1:1 System RF IN (WR75) TEST IN -40 db OFFLINE IN CONTROLLER. 1:2 System POL 1 IN (WR75) TEST IN -40 db POL 2 IN
BRK-1000 Series Ku-Band Redundant LNB Systems Introduction Redundant LNB systems minimize system downtime due to LNB failure by providing a spare LNB and an automatic means of switching to the spare upon
More informationPOINTS POSITION INDICATOR PPI4
POINTS POSITION INDICATOR PPI4 Monitors the brief positive operating voltage across points motors when they are switched Lights a corresponding led on a control panel to show the last operation of each
More informationSINGLE ZONE CLIMATE ZONING SYSTEM. Technical Manual. Polyaire Pty Ltd
SINGLE ZONE CLIMATE ZONING SYSTEM Technical Manual Polyaire Pty Ltd 11-13 White Road GEPPS CROSS South Australia, 5094 Tel: (08) 8349 8466 Fax: (08) 8349 8446 www.polyaire.com.au CONTENTS Features 1 Application
More informationXW3D. Simple Wiring of Sensor Actuators. Connector Terminal Boxes. Specifications. Materials and Finish. Connection Combinations
Terminal Boxes XWD CSM_XWD_DS_E Simple Wiring of Sensor Actuators Greatly reduce wiring in combination with the Smartclick XS. Insert the connector and turn / of a turn to lock the connectors. Higher rated
More informationProduct Operation Manual
Product Operation Manual VL-FTX FORWARD TRANSMITTER MODULE Ver 1.1(Doc#01-02-008) VALE SYSTEMS INC. 10400 Overland Road #408 Boise, ID 83709-1449,USA Tel: 208.935.6317Fax: 208.935.6234 All rights reserved
More information7 Day Digital Time Switch
7 Day Digital Time Switch Model: NTT08 Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference and maintenance. 2.
More informationRevision 1.2d
Specifications subject to change without notice 0 of 16 Universal Encoder Checker Universal Encoder Checker...1 Description...2 Components...2 Encoder Checker and Adapter Connections...2 Warning: High
More informationCaution. Hanging the Screen:
Installation Instructions for Laminar and Laminar XL Projection Screens Caution 1. Read Instructions through completely before proceeding; keep them for future reference. Follow these instructions carefully.
More informationAWT150C/AWT150CS/ AWT151C CCD Camera
AWT150C/AWT150CS/ AWT151C CCD Camera ISSUED OCTOBER 2018 WARNING Failure to follow all instructions and safety precautions in this manual, in the vehicle and body manufacturers' manuals and on the safety
More informationPXI MICROWAVE. Model PXI-1420
The PXI-1420 MW Downconverter Module is a PXI 3U, 1-slot downconverter module that, in conjunction with Local Oscillator Module PXI-1450B, converts microwave signals within the 2.75 to 26.5 GHz frequency
More informationCURRENT INJECTION RELAY TESTER CR-100. ( Code P60212 (770081) ) INSTRUCTIONS MANUAL ( M / 05A ) (c) CIRCUTOR S.A.
CURRENT INJECTION RELAY TESTER CR-100 ( Code P60212 (770081) ) INSTRUCTIONS MANUAL ( M 981 329 / 05A ) (c) CIRCUTOR S.A. ---- CURRENT- TIME TRIP TESTER CR-100 --------------- Page. 2 CURRENT INJECTION
More informationOperating Manual (Edition 04/2004) sinamics. Line Reactors SINAMICS G130
Operating Manual (Edition 04/2004) sinamics Line Reactors SINAMICS G130 Contents 1. Safety Information 2 2. General 5 3. Mechanical Installation 6 4. Electrical Installation 8 5. Technical Specifications
More informationKD-VP800 RGBHV-to-Component Digital Video Scaler & Video Adapter
KD-VP800 RGBHV-to-Component Digital Video Scaler & Video Adapter Operating Instructions The KD-VP800 by Key Digital is a universal analog Video Scaler and Adapter that converts RGBHV Video sources to Component
More informationLED Driver Compact fixed output
Driver LC 40W 900mA fixc C SNC ESSENCE series Product description Fixed output built-in LED Driver Constant current LED Driver Output current 900 ma Max. output power 40 W Nominal life-time up to 50,000
More informationMulticom Optical Return Path Receiver MUL HRPR 4B
Multicom Optical Return Path Receiver User Manual v.9 www.multicominc.com 800 423 2594 407 331 7779 1076 Florida Central Parkway, Longwood, FL 32750 SAFETY NOTIFICATION Multicom strongly advises you to
More informationSlot-type Photomicrosensor with connector or pre-wired models (Non-modulated) *1. configuration. Dark-ON/Light-ON
Slot-type Photomicrosensor with connector or pre-wired models (Non-modulated) * EE-SX/6 Photomicrosensor with 0- to 00-mA direct switching capacity for built-in application. Series includes models that
More informationVK-P10SE WARRANTY REGISTRATION FORM
VK-P10SE WARRANTY REGISTRATION FORM Unit Serial Number: Customer Name: Address: Date of Purchase: Purchased From: Dealer Name: Address: IMPORTANT NOTE: In order to receive the full five-year product warranty,
More informationPLL2210MW LED Monitor
PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationQuick Reference for Operation
For Installer Company Use For Maintenance and Inspection Use Model TPD-T250P6-US Three-phase Inverter Unit Model EOW-MBX03-US Master Box for Three-phase Inverter The content of this Quick Reference is
More informationT5, T8, TC-L. PC T5 PRO lp W V 50/60/0 Hz, HO. Electronic ballasts Linear lamps T5, T8 and compact lamps TC-L
T, T8, TC-L Electronic ballasts PC T PRO lp 80 W 0 0 V 0/0/0 Hz, HO L D,1 0, 1 side fixing feature side fixing feature ø,1 defined lamp warm start is 1. s constant light output independent of fluctuations
More informationSolis Export Power Manager
Solis Export Power Manager Installation and Operation Manual Ningbo Ginlong Technologies Co., Ltd. No. 57 Jintong Road, Binhai Industrial Park, Xiangshan, Ningbo, Zhejiang, 3572, P.R.China Tel: +86 (0)574
More informationVHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies
VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies VHF: 54-216 MHz UHF: 470-698 MHz FM: 87.9-107.9 MHz Voltage Input: AC110-120V / AC220-240V Working:
More informationDMX48. User s instruction manual. 24 Channel DMX controller
WWW.LIGHTEMOTIONS.COM.AU DMX48 24 Channel DMX controller User s instruction manual This manual contains important information about the safe installation and use of this product Please read this instruction
More informationGeneral Wiring and Installation Guidelines. Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers
General Wiring and Installation Guidelines Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers Congratulations on your purchase of a Dynapar brand encoder.
More informationColour Explosion Proof Video Camera USER MANUAL VID-C
Colour Explosion Proof Video Camera USER MANUAL VID-C Part Number: MAN-0036-00 Rev 4 Copyright 2002 Net Safety Monitoring Inc. Printed in Canada This manual is provided for informational purposes only.
More informationACT 10 Digital Keypad Operating & Installation Instructions This manual is found at
ACT 10 Digital Keypad Operating & Installation Instructions 18-00001 This manual is found at www.eaglesecuritysolutions.co.uk Installation Notes Always remember to factory default the controller before
More informationSensor module. Safety instructions. Function Correct use. Product characteristics. Structure of the device. Operation. Ref.No.
Sensor module Ref.No.: SM 1608 V03 Safety instructions Caution! Electrical devices may only be installed and fitted by electrically skilled persons. Non-compliance with the installation information could
More information2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU
2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU 1 The 3613WDU Analog Temperature / RH Sensor Upgrade Kit is used to upgrade Watchdog 2000 Series Weather
More informationPHASED OUT. LED control gear Compact fixed output. Driver LC 40W 900mA fixc C SNC China Domestic ESSENCE series
Product description Fixed output built-in LED Driver Constant current LED Driver Output current 900 ma Max. output power 40 W Nominal life-time up to 30,000 h For luminaires of protection class I and protection
More information