LCD TV OWNER S MANUAL

Transcription

1 LCD TV OWNER S MNUL Hospital Grade Models LG3DCH 6LG3DCH 3LG3DCH Lodging Grade Model 3LG3DC Installer Reference for Commercial Mode Commercial Mode Setup see pages 9-0 Channel Banks Setup see pages Pillow Speaker Setup see page 9 MPI/PPV Card Setup see page 0 Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. Note: ll features shown within this guide may not be available on all models. P/NO : SC (080-REV00)

2

3 WRNING / CUTION WRNING / CUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BCK). NO USER SERVICEBLE PRTS INSIDE. REFER TO QULIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WRNING/CUTION TO REDUCE THE RISK OF FIRE ND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RIN OR MOISTURE. NOTE TO CBLE/TV INSTLLER This reminder is provided to call the CTV system installer s attention to rticle of the National Electric Code (U.S..). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/tv technician for help. ny changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. CUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user s authority to operate this product

4 SFETY INSTRUCTIONS IMPORTNT SFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 6 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Do not use this apparatus near water. 7 Only use attachments/accessories specified by the manufacturer. Clean only with dry cloth. 3 Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 4 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. 9 Unplug this apparatus during lighting storms or when unused for long periods of time. 5 Do not defeat the safety purpose of the polarized or grounding-type plug. polarized plug has two blades with one wider than the other. grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 0 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

5 Never touch this apparatus or antenna during a thunder or lighting storm. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. 5 WRNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 3 Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. 4 CUTION concerning the Power Cord : It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same C power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. ny of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit). GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. (i.e. a TV with a three-prong grounded C plug must be connected to a three-prong grouned C outlet) If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Short-circuit Breaker Power Supply DISCONNECTING DEVICE FROM MINS Mains plug is the disconnecting device. The plug must remain readily operable. 9 Keep the product away from direct sunlight. 3

6 0 NTENNS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. n outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 80 of the National Electrical Code (NEC) in the U.S.. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. ntenna grounding according to the National Electrical Code, NSI/NFP Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places. If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center. Ground Clamp ntenna Lead in Wire Electric Service Equipment ntenna Discharge Unit (NEC Section 80-0) Grounding Conductors (NEC Section 80-) Ground Clamps Power Service Grounding Electrode System (NEC rt 50, Part H) 5 Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it. NEC: National Electrical Code 4

7 CONTENTS WRNING / CUTION SFETY INSTRUCTIONS FETURES OF THIS TV PREPRTION ccessories Front Panel Information Back Panel Information Stand Instruction Cable Management Desktop Pedestal Installation Swivel Stand ttaching the TV to a desk VES Wall Mounting VES Standard TV Mounts Securing the TV to the wall to prevent falling When the TV is used on a stand ntenna or Cable Connection MPI Card Slot EXTERNL EQUIPMENT SETUP HD Receiver Setup DVD Setup VCR Setup Other /V Source Setup Pillow Speaker Setup PC Setup WTCHING TV / CHNNEL CONTROL Remote Control Functions Installer Remote Control Functions Turning On TV Channel Selection Volume djustment On-Screen Menus Selection Channel Setup - uto Scan (uto Tuning) dd / Delete Channel (Manual Tuning) Channel Editing Channel Label Input List PICTURE CONTROL Picture Size (spect Ratio) Control Preset Picture Settings - Picture Mode - Preset Color Tone - Preset Manual Picture djustment - Picture Mode - User Mode Picture Mode - Expert Control Picture Improvement Settings dvanced Control - Black (Darkness) Level dvanced Control - Real Cinema Picture Reset SOUND & LNGUGE CONTROL uto Volume Leveler (uto Volume) Clear Voice Preset Sound Settings (Sound Mode) Sound Setting djustment - User Mode SRS TruSurround XT Balance TV Speakers On/Off Setup udio Reset Stereo/SP Broadcast Setup udio Language On-Screen Menus Language Selection Caption Mode - nalog Broadcasting System Captions Digital Broadcasting System Captions Caption Option TIME SETTING Clock Setting - uto Clock Setup Manual Clock Setup uto On/Off Time Setting Sleep Timer Setting uto Shut-off Setting

8 PRENTL CONTROL / RTINGS Set Password & Lock System Channel Blocking Movie & TV Rating Downloadable Rating External Input Blocking CHNNEL BNKS Channel Banks Overview Channel Banks Setup Installer Remote Control Key Functions Channel Banks Setup Reference: Channel Banks Worksheet PPENDIX Troubleshooting Reference: LT00 Cloning Procedure Troubleshooting Channel Banks Setup Troubleshooting Troubleshooting Flow Chart Commercial Mode Check Glossary of Terms Maintenance Product Specifications IR Codes COMMERCIL MODE SETUP Installer Overview TV overview Commercial Mode Setup for Master TV Master TV Profile Setup Learning/Teaching with USB Memory Card TLL-00 Clone Connections / Learning and Teaching Setups LT00 Cloning Connections/Learning Setup.. 97 Cloning Learning Setup Cloning Connections/Teaching Setup Installer Menu Reference: Detailed Information For Making Master TV Reference: Procedures for adding Channel Label Icons/Custom Channel Labels ( Mode) Reference: Clonable Menu Features Reference: Checking Software Version TV ux Input Configuration Power Saving Setup

9 FETURES OF THIS TV HDMI TM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing." Manufactured under license from Dolby Laboratories. Dolby and the double-d symbol are trademarks of Dolby Laboratories. is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. USB IN SERVUCE ONLY USB port shall be used for software update by service personnel only. FOR LCD TV If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. void touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 7

10 POWER Copyright 007 LGE, ll Rights Reserved. PREPRTION PREPRTION CCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. 6/3LG3DCH, 3LG3DC only Owner s Manual LG3DCH only CD Manual Power Cord Protective Bracket and Bolt for Power Cord (Refer to P.3) (This feature is not available for all models.) Protection Cover (Refer to P.) Cable Management Clip (Refer to P.3) Polishing Cloth (This feature is not available for all models.) * Wipe spots on the exterior only with the polishing cloth. * Do not wipe roughly when removing stains. Excessive pressure may cause scratches or discoloration. 3LG3DC only VOL CH MUTE CC DJUST RETURN - TIMER FLSHBK PICTURE SOUND RTIO.5V.5V Remote Control, Batteries 9 TV INPUT SP M4xL6 (Machine Screw) x 4 x 4 Ø4xL0 (Plastic Screw) Bolts for stand assembly (Refer to P.) x M4xL (Machine Screw) Torx plus Star head screw (Refer to P.) Ø4xL0 (Plastic Screw) Screw for stand fixing (Refer to P.5) Optional Installer Remote Control for Model No. Series /6/3LG3DCH There is an optional Installer remote control available for the /6/3LG3DCH models. The installer remote control is NOT included with the TV. Option Extras D-sub 5 pin Cable When using the VG (D-sub 5 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance. Wall Mounting Bracket (RW0) (Only LG3DCH) Wall Mounting Bracket (RW30) (Only 6LG3DCH) Tilt Wall Mounting Bracket (W-47LG30M) (Only 3LG3DCH) 8

11 FRONT PNEL INFORMTION Image shown may differ from your TV. NOTE: If your TV has a protection tape attached, remove the tape. nd then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it). CH CHNNEL(+, -) Buttons PREPRTION Stand 3LG3DC model LG3DCH model (only 3LG3DC) POWER Button Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on. Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates green when the set is switched on. VOL INPUT VOLUME (+, -) Buttons Button Button INPUT Button Headphone POWER Button Remote Control Sensor 6/3LG3DCH model Power/Standby Indicator Illuminates red in standby mode. Illuminates green when the set is switched on. Remote Control Sensor POWER Button 9

12 PREPRTION BCK PNEL INFORMTION Image shown may differ from your TV. PREPRTION For 3LG3DC 6/3LG3DCH H/P L/MONO UDIO R VIDEO NTENN IN M.P.I. V IN (only 6/3LG3DCH model) 3 UPDTE RESET 7 V IN S-VIDEO COMPONENT IN HDMI/DVI IN VIDEO UDIO USB IN SERVUCE ONLY ( MONO) VIDEO UDIO RS-3C IN (SERVICE ONLY) RGB IN (PC) UDIO IN (RGB/DVI) 5 PILLOW SPEKER 8 REMOTE CONTROL OUT NORML SPEKER PILLOW SPEKER SPEKER SWITCH 6 SPEKER OUT

13 For LG3DCH NTENN IN M.P.I. 3 4 PILLOW SPEKER HDMI/DVI IN 5 V IN 4 PREPRTION 5 5 PILLOW NORML SPEKER SPEKER SPEKER SWITCH RS-3C IN (SERVICE ONLY) USB IN REMOTE SERVUCE ONLY CONTROL OUT VIDEO ( MONO ) UDIO 9 DVI UDIO IN RESET UPDTE V (udio/video) IN nalog composite connection. Supports standard definition video only (480i). Used for PC/DTV audio input jack (Only LG3DCH- U model). S-VIDEO (Except LG3DCH model) Better quality than standard composite (yellow RC cable). Supports standard definition video only (480i). HDMI/DVI IN Digital Connection. Supports HD video and Digital audio. ccepts DVI video using an adapter or HDMI to DVI cable (not included). USB IN SERVICE ONLY Used for software updates. UPDTE Software downloads and debug mode enable/disable. RESET Hardware reset to PTC microcontroller. RS-3C IN (SERVICE ONLY) Used for software updates. RGB IN (PC) (Except LG3DCH model) nalog PC Connection. Uses a D-sub 5 pin cable (VG cable) COMPONENT IN (Except LG3DCH model) nalog Connection. Supports HD. Uses a red, green, and blue cable for video & a red and white cable for audio. UDIO IN (RGB/DVI) (Except LG3DCH model) /8 headphone jack for analog PC audio input. REMOTE CONTROL OUT IR output for controlling an auxiliary device. SPEKER OUT 8Ω (Except LG3DCH model) H/P Plug the headphone into the headphone socket. Power Cord Socket For operation with C power. Caution: Never attempt to operate the TV on DC power. NTENN IN Connect over-the air signals to this jack. M.P. I. PILLOW SPEKER (Except 3LG3DC model) Used to connect to pillow speaker. SPEKER SWITCH (Except 3LG3DC model) Used to select the speaker output switch. Note: If Pillow Speaker is selected, no Sound will be heard from TV speakers. (NORML SPEKER or PILLOW SPEKER)

14 PREPRTION STND INSTRUCTION Image shown may differ from your TV. PREPRTION INSTLLTION (Only 3LG3DC) Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. DETCHMENT (Only 3LG3DC) Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. ssemble the parts of the STND BODY with COVER BSE of the TV. Remove the four screws that hold the base on. STND BODY COVER BSE 3 Insert the stand as shown. 3 Detach the stand from TV. 4 x 4 Tighten the stand with the four screws (provided as parts of the TV). or Tighten the two of these four screws x x and the two Torx plus star head screws (provided as parts of the TV) to secure the TV. Tighten the two Torx plus star head screws with a star head driver bit (not provided as parts of the TV). PROTECTION COVER (Except LG3DCH) fter removing the stand, install the included protection cover over the hole for the stand. Press the PROTECTION COVER into the TV until you hear it click.! NOTE G Make sure the screws in the stand are fully tightened. (If not tightened fully, the product could tilt forward and fall). But do not over tighten, over-tightening can damage the threads on the screws.

15 CBLE MNGEMENT Image shown may differ from your TV. For 6/3LG3DCH, 3LG3DC Connect the cables as necessary. To connect additional equipment, see the EXTERNL EQUIPMENT SETUP section. Secure the power cable with the PROTECTIVE BRCKET and the screw as shown. It will help prevent the power cable from being removed by accident. For LG3DCH Connect the cables as necessary. To connect additional equipment, see the EXTERNL EQUIPMENT SETUP section. Secure the power cable with the PROTECTIVE BRCKET and the screw as shown. It will help prevent the power cable from being removed by accident. PREPRTION PROTECTIVE BRCKET (This feature is not available for all models.) Install the CBLE MNGEMENT CLIP as shown. PROTECTIVE BRCKET (This feature is not available for all models.) Install the CBLE MNGEMENT CLIP as shown. CBLE MNGEMENT CLIP 3 CBLE MNGEMENT CLIP Fit the CBLE MNGEMENT CLIP as shown. 3 Put the cables inside the CBLE MNGEMENT CLIP and snap it closed. How to remove the CBLE MNGEMENT CLIP G Hold the CBLE MNGE- MENT CLIP with both hands and pull it backward.! NOTE G Do not hold the CBLE MNGEMENT CLIP when moving the TV. - If the TV is dropped, you may be injured or the product may be broken. 3

16 PREPRTION DESKTOP PEDESTL INSTLLTION Image shown may differ from your TV. * This feature is not available for all models. PREPRTION For proper ventilation, allow a clearance of 4 inches on all four sides. 4 inches 4 inches 4 inches 4 inches CUTION G Ensure adequate ventilation by following the clearance recommendations. G Do not mount near or above any type of heat source. SWIVEL STND (Only 3LG3DC) The TV can be conveniently swivelled on its stand 90 to the left or right to provide the optimum viewing angle. 4

17 TTCHING THE TV TO DESK (Only 3LG3DC) The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only the included screw. Stand PREPRTION -Screw (provided as parts of the product) Desk WRNING G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the TV may cause injury. 5

18 PREPRTION VES WLL MOUNTING PREPRTION Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. B Product LCD TV Model 6LG3DCH, 3LG3DCH 3LG3DC VES ( * B) Standard Screw Quantity 00 * 00 M4 4 LG3DCH 00 * 00 M4 4! NOTE G Screw length needed depends on the wall mount used. For further information, refer to the instructions included with the mount. G Standard dimensions for wall mount kits are shown in the table. G When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. G Do not use screws longer then the standard dimension, as they may cause damage to the inside to the TV. G For wall mounts that do not comply with the VES standard screw specifications, the length of the screws may differ depending on their specifications. G Do not use screws that do not comply with the VES standard screw specifications. Do not tighten the screws too much. It may damage the TV or allow the TV to a fall and cause personal injury. LG is not liable for these kinds of accidents. G LG is not liable for TV damage or personal injury when a non-ves or non specified wall mount is used or the consumer fails to follow the TV installation instructions. CUTION G Do not install your wall mount kit while the TV is plugged in. It may result in personal injury due to electric shock. WRNING G To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions. 6

19 VES STNDRD TV MOUNTS General Guidelines: Choosing a Location for installing a VES Standard Mount To the right are some examples of VES standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instructions provided with the TV stand that will be used to mount the TV. Be sure the style of stand selected is capable of supporting the weight of the TV and is appropriate for the application. Typical Wall Stud Type Mount with Swivel Bracket PREPRTION Wall Mounts If the mount will be on a wall, a typical wooden stud behind the wall board would be the preferred choice for a location to attach the wall mount. The wall mount location chosen should be appropriate for drilling holes and have available the required power source as well as antenna/cable and any other equipment leads as necessary. Pedestal Mounts and Stands sturdy surface on a desk or other similar flat table-like furniture would be the appropriate location for mounting a pedestal-style TV stand. Most stands are designed so that the wiring is threaded through the stand itself or a loop-through style clamp so that the wiring is neatly bunched and not strung in such a way as to create a potential hazard to the user. (Some stands are portable and can be moved from one location to another.) Be sure all safety considerations are followed. Typical Pedestal Type Mount with Swivel Bracket 7

20 PREPRTION SECURING THE TV TO THE WLL TO PREVENT FLLING WHEN THE TV IS USED ON STND You should purchase necessary components to prevent TV from falling off of the stand. PREPRTION Image shown may differ from your TV. * This feature is not available for all models. We recommend that you set the TV close to a wall so it cannot fall over if pushed backwards. dditionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don t climb on or hang from the TV. Insert eye-bolts (or TV brackets and bolts) to attach the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with screws (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. Use a sturdy rope or cord (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product (the less slack in the rope, the better).! NOTE G Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. G To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are the same. 8

21 To prevent damage do not connect to the power outlet until all connections are made between the devices. NTENN OR CBLE CONNECTION. ntenna (nalog or Digital) Wall ntenna Socket or Outdoor ntenna without a Cable Box Connection. For optimum picture quality, adjust the direction if needed. Wall ntenna Socket Multi-family Dwellings/partments (Connect to wall antenna socket) NTENN IN PREPRTION Outdoor ntenna (VHF, UHF) RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna.. Cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) NTENN IN To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TV s, install a -Way Signal Splitter. If the antenna is not installed properly, contact your dealer for assistance. 9

22 PREPRTION MPI CRD SLOT The MPI card is equipped with an RF jack for antenna/cable signal source connection. The slot is also available for installing a PPV (Pay-Per-View) card. PREPRTION MPI Card Removal / PPV Card Installation. Remove the two MPI card retainer screws.. Pull out current MPI card far enough so that the RF cable can be detached from the old card.. Detach RF cable. 3. Place new PPV card into slot and slide it in far enough to reconnect RF cable. 4. Reconnect RF cable. 5. Insert card all the way into the slot making sure it is fully seated into back plane connector. 6. Replace the two card retainer screws. NTENN IN M.P.I. R F C B L E RF cable needs to be disconnected to remove current card. M.P. I. Card Slot 0

23 EXTERNL EQUIPMENT SETUP To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. This part of EXTERNL EQUIPMENT SETUP mainly uses the picture for 3LG3DC model. HD RECEIVER SETUP This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. Component Connection (Except LG3DCH). How to connect Connect the video outputs (Y, PB, PR) of the digital settop box to the COMPONENT IN VIDEO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).. How to use Connect the audio output of the digital set-top box to the COMPONENT IN UDIO jacks on the TV. Turn on the digital set-top box. (Refer to the owner s manual for the digital set-top box.) Select Component input source using the INPUT button on the remote control. V IN S-VIDEO COMPONENT IN Y PB PR L R HDMI/DVI IN UPDTE VIDEO UDIO USB IN SERVUCE ONLY ( MONO) VIDEO UDIO RS-3C I (SERVICE ON RGB IN (PC UDIO (RGB/D EXTERNL EQUIPMENT SETUP Supported Resolutions Signal Component 480i Yes 480p Yes 70p Yes 080i Yes 080p No HDMI Yes Yes Yes Yes Yes Y, CB/PB, CR/PR Resolution 70x480i 70x480p 80x70p 90x080i Horizontal Frequency(KHz) Vertical Frequency(Hz)

24 EXTERNL EQUIPMENT SETUP HDMI Connection. How to connect UP EXTERNL EQUIPMENT SETUP. How to use Connect the digital set-top box to HDMI/ DVI IN jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. Turn on the digital set-top box. (Refer to the owner s manual for the digital set-top box.) Select HDMI input source with using the INPUT button on the remote control. V IN S-VIDEO COMPONENT IN HDMI/DVI IN VIDEO UDIO USB IN SERVUCE ONL ( MONO) VIDEO U HDMI-DTV OUTPUT HDMI-DTV Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 70x480i 70x480p 80x70p 90x080i 90x080p

25 DVI to HDMI Connection. How to connect. How to use Connect the DVI output of the digital set-top box to the HDMI/DVI IN jack on the TV. Connect the audio output of the digital set-top box to the UDIO IN(RGB/DVI) or V IN UDIO jack on the TV. Turn on the digital set-top box. (Refer to the owner s manual for the digital set-top box.) Select the HDMI input source on the TV using the INPUT button on the remote control. 6/3LG3DCH, 3LG3DC model V IN S-VIDEO COMPONENT IN HDMI/DVI IN VIDEO UDIO USB IN SERVUCE ONLY ( MONO) VIDEO UDIO RS-3C IN (SERVICE ONLY) RGB IN (PC) UDIO IN (RGB/DVI) EXTERNL EQUIPMENT SETUP DVI-DTV OUTPUT L R LG3DCH model! NOTE HDMI/DVI IN V V IN IN G DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. L ER H RS-3C IN (SERVICE ONLY) USB IN REMOTE SERVUCE ONLY CONTROL OUT UDIO ( MONO ) VIDEO DVI UDIO IN RESET UPDTE DVI-DTV OUTPUT L R 3

26 EXTERNL EQUIPMENT SETUP DVD SETUP Component Connection (Except LG3DCH). How to connect EXTERNL EQUIPMENT SETUP Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio outputs of the DVD to the COMPONENT IN UDIO jacks on the TV.. How to use Turn on the DVD player, insert a DVD. Select the Component input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. V IN S-VIDEO COMPONENT IN Y PB PR L R HDMI/DVI IN UPDTE VIDEO UDIO USB IN SERVUCE ONLY ( MONO) VIDEO UDIO RS-3 (SERVICE RGB IN U (RG Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Y PB PR Y PB PR Video output ports on DVD player Y Y B-Y Cb R-Y Cr Y Pb Pr 4

27 S-Video Connection (Except LG3DCH). How to connect HDMI/DVI IN USB IN SERVUCE ONLY. How to use Connect the S-VIDEO output of the DVD to the S -VIDEO input on the TV. Connect the audio outputs of the DVD to the UDIO input jacks on the TV. Turn on the DVD player, insert a DVD. Select the V input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. V IN S-VIDEO COMPONENT IN S-VIDEO L UDIO VIDEO UDIO R ( MONO) VIDEO UDIO EXTERNL EQUIPMENT SETUP HDMI Connection. How to connect UPD Connect the HDMI output of the DVD to the HDMI/DVI IN jack on the TV. HDMI/DVI IN USB IN SERVUCE ONLY No separate audio connection is necessary. HDMI supports both audio and video. V IN S-VIDEO UDIO ( MONO) VIDEO. How to use Select the HDMI input source on the TV using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. COMPONENT IN VIDEO UDI HDMI OUTPUT 5

28 EXTERNL EQUIPMENT SETUP VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and TV. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty. EXTERNL EQUIPMENT SETUP ntenna Connection. How to connect Connect the RF antenna out socket of the VCR to the NTENN IN socket on the TV. S-VIDEO VIDEO L R NT OUT NTENN IN Connect the antenna cable to the RF antenna in socket of the VCR. OUTPUT SWITCH NT IN Wall Jack. How to use Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLY on the VCR. (Refer to the VCR owner s manual.) ntenna 6

29 Composite (RC) Connection. How to connect. How to use Connect the UDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, udio Left = white, and udio Right = red) Insert a video tape into the VCR and press PLY on the VCR. (Refer to the VCR owner s manual.) Select the V or V input source on the TV using the INPUT button on the remote control. If connected to V IN, select V input source on the TV (Except LG3DCH).! NOTE G If you have a mono VCR, connect the audio cable from the VCR to the UDIO L(MONO) jack of the TV. V IN S-VIDEO COMPONENT IN NT OUT NT IN VIDEO R UDIO ( MONO) VIDEO RGB IN (P L VIDEO UDIO S-VIDEO OUTPUT SWITCH UDIO (RGB/ EXTERNL EQUIPMENT SETUP S-Video Connection (Except LG3DCH). How to connect V IN S-VIDEO UDIO ( MONO) VIDEO R Connect the S -VIDEO output of the VCR to the S -VIDEO input on the TV. COMPONENT IN VIDEO UDIO Connect the audio outputs of the VCR to the UDIO input jacks on the TV.. How to use Insert a video tape into the VCR and press PLY on the VCR. (Refer to the VCR owner s manual.) Select the V input source on the TV using the INPUT button on the remote control. S-VIDEO VIDEO OUTPUT SWITCH L R NT OUT NT IN! NOTE G S-Video provides better quality than composite. Use it when available. CUTION G Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. 7

30 EXTERNL EQUIPMENT SETUP OTHER /V SOURCE SETUP. How to connect 6/3LG3DCH, 3LG3DC model Camcorder EXTERNL EQUIPMENT SETUP. How to use Connect the UDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, udio Left = white, and udio Right = red) Select the V input source on the TV using the INPUT button on the remote control. (Except LG3DCH) If connected to V IN or V IN input, select the V or V input source on the TV. Operate the corresponding external equipment. H/P L/MONO UDIO R VIDEO VIDEO L Video Game Set R V IN LG3DCH model Camcorder Video Game Set VIDEO L R N N Y) EMOTE TROL OUT VIDEO ( MONO ) UDIO V IN DVI UDIO IN RESET UPDTE 8

31 PILLOW SPEKER SETUP Connect a pillow speaker to the LCD TV/Monitor.. How to connect (Except 3LG3DC) 3 Connect the PILLOW SPEKER output jack on the back of the TV. Connect an acccessory pillow speaker or wired remote control unit to this 6-pin jack. Select PILLOW SPEKER on the rear panel of the TV. NOTE: If the pillow speaker switch is set to Pillow Speaker, no sound will be heard from the TV speakers. lso, uto Volume will be grayed out and not accessible on the Sound menu. Use a pillow speaker that is a UL recognized pendant control bearing the warning: Risk of fire if used in oxygen enriched atmosphere. Keep pendant control away from oxygen equipment. PILLOW SPEKER NORML SPEKER PILLOW SPEKER SPEKER SWITCH EXTERNL EQUIPMENT SETUP Controlling the TV with Serial Data The TV is capable of being controlled by a single-wire, serial data signal. This is a LG patented technology and is being implemented by certain brands of smart pillow speakers. Pillow Speaker Interface This connector furnishes three control lines and an audio output. patient-pendant remote control, or entertainment audio and nurse call system may be connected here. ll lines are isolated from the C power line and earth ground. (Optoisolators isolate the control lines, and a transformer isolates the audio. There are no relays or inductive components in the control lines.) pin No Purpose External TV On/Off switch. (Not used.) External Channel Up switch or Data in. Common connection for control, data, and audio output. Impedance to earth ground is a 0-meg resistor in parallel with a 00 pf capacitor. Isolated audio output. Nominal 4-ohm source impedance with short circuit protection. Intended for a pillow speaker with a low-impe ance pad-type volume control. External Channel Down switch. Controlling the TV with Mechanical Switches Pin 4(common) is momentarily connected to pin, 3, or 6 via push-action switches to control On/Off and Channel Up/Down. These pins are at +3volts DC(when measured from pin4) with the switches open. Current draw is 8 m when a switch is closed. (This operation is identical to previous LG models using the 5-Wire Interface except that only +7 volts DC was supplied and current draw was only.5 m.) 9

32 EXTERNL EQUIPMENT SETUP PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VG (D-Sub 5 pin) Connection (Except LG3DCH) NO) VIDEO RGB IN (PC). How to connect EXTERNL EQUIPMENT SETUP. How to use Connect the VG output of the PC to the R G B I N(P C) jack on the TV. Connect the PC audio output to the UDIO IN (RGB/DVI) jack on the TV. Turn on the PC and the TV. Select the RGB input source on the TV using the INPUT button on the remote control. UDIO UDIO IN (RGB/DVI) REMOT CONTROL Supported Display Specifications (RGB-PC, HDMI-PC) RGB OUTPUT UDIO Resolution 640x350 70x x x600 04x768 80x x x768 Horizontal Frequency(KHz) Vertical Frequency(Hz) * Only RGB-PC mode! NOTES G To get the the best picture quality, adjust the PC graphics card to 360x768. G Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. G In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. G void keeping a fixed image on the screen for a long period of time. The fixed image could become permanently imprinted on the screen. G The synchronization input form for Horizontal and Vertical frequencies is separate. G Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. 30

33 DVI to HDMI Connection 6/3LG3DCH, 3LG3DC model. How to connect. How to use Connect the DVI output of the PC to the HDMI/DVI IN jack on the TV. Connect the PC audio output to the UDIO I N (RGB/DVI) or V IN UDIO jack on the TV. Turn on the PC and the TV. Select the HDMI input source on the TV using the INPUT button on the remote control. V IN S-VIDEO COMPONENT IN HDMI/DVI IN VIDEO DVI-PC OUTPUT UDIO USB IN SERVUCE ONLY ( MONO) UDIO UPDTE VIDEO UDIO RS-3C IN (SERVICE ONLY) RGB IN (PC) UDIO IN (RGB/DVI) EXTERNL EQUIPMENT SETUP LG3DCH model HDMI/DVI IN V V IN IN L R RS-3C IN (SERVICE ONLY) UDIO ( MONO ) VIDEO DVI UDIO IN RESET UPDTE USB IN SERVUCE ONLY REMOTE CONTROL OUT DVI-PC OUTPUT UDIO 3

34 EXTERNL EQUIPMENT SETUP Screen Setup for PC mode (Except LG3DCH) Selecting Resolution You can choose the resolution in RGB mode. The Position, Phase, and Size can also be adjusted. EXTERNL EQUIPMENT SETUP Screen Prev. Resolution uto config. Position Size Phase Reset G 04 x x x x DJUST RETURN Press the DJUST button. Select Resolution. Select the desired resolution. Return to TV viewing. You can also adjust Screen(RGB-PC) in the PICTURE menu. 3

35 uto Configure utomatically adjusts picture position and minimizes image instability. fter adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. Screen Prev. Resolution uto config. G Position Size Phase Reset Yes To Set No EXTERNL EQUIPMENT SETUP DJUST 3 4 Press the DJUST button. Select uto config.. Select Yes. Start uto Configuration. If the position of the image is still not correct, try uto adjustment again. If picture needs to be adjusted again after uto adjustment in RGB, you can adjust the Position, Size or Phase. 33

36 EXTERNL EQUIPMENT SETUP djustment for screen Position, Size, and Phase EXTERNL EQUIPMENT SETUP If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB mode. Screen Prev. Resolution uto config. Position Size Phase Reset G F D E G 3 4 DJUST RETURN Press the DJUST button. Select Position, Size, or Phase. Make appropriate adjustments. Return to TV viewing. Position: This function is to adjust picture to left/right and up/down as you prefer. Size: This function is to minimize any vertical bars or stripes visible on the screen background. nd the horizontal screen size will also change. The Size adjustment range is -30 ~ 30. Phase: This function allows you to remove any horizontal noise and clear or sharpen the image of characters. The Phase adjustment range is -3 ~ 3. 34

37 Screen Reset (Reset to original factory values) Returns Position, Size, and Phase to the default factory settings. This feature operates only in RGB mode. Screen Prev. Resolution uto config. Position Size Phase Reset G Initialize Settings. Yes No EXTERNL EQUIPMENT SETUP 3 DJUST Press the DJUST button. Select Reset. Select Yes. 4 35

38 WTCHING TV / CHNNEL CONTROL REMOTE CONTROL FUNCTIONS (Only 3LG3DC) When using the remote control, aim it at the remote control sensor on the TV. POWER Turns your TV on or off. TV In V-, Component, RGB, and HDMI input sources, screen returns to the last TV channel. POWER TV INPUT PICTURE SOUND SP RTIO WTCHING TV / CHNNEL CONTROL INPUT PICTURE SOUND SP RTIO External input modes rotate in regular sequence: TV, V-, Component, RGB, and HDMI. Selects the factory preset picture depend on the viewing environment. G p.5 Selects the factory preset sound for type of program. G p.6 nalog mode: Selects MTS sound (Mono, Stereo, or a SP). G p.67 DTV mode: Changes the audio language. Change the aspect ratio. G p TIMER VOL CC MUTE DJUST FLSHBK CH RETURN THUMBSTICK (Up/Down/Left Right/) Navigate the on-screen menus and adjust the system settings to your preference. 36

39 NUMBER button (DSH) Used to enter a program number for multiple program channels such as -, -, etc. FLSHBK VOLUME UP /DOWN TIMER CC MUTE CHNNEL UP/DOWN DJUST Tune to the last channel viewed. Increase/decrease the sound level. Select the amount of time before your TV turns off automatically. G p.76 Select a closed caption. G p.70 Switch the sound on or off. G p.4 Select available channels. djust the screen resolution, position, size and phase. G p.3 - p.35 Displays the main menu. WTCHING TV / CHNNEL CONTROL RETURN llows the user to move return one step in an interactive application or other user interaction function. Installing Batteries Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -). Install two.5v batteries. Don t mix old or used batteries with new ones. Close cover. 37

40 WTCHING TV / CHNNEL CONTROL INSTLLER REMOTE CONTROL FUNCTIONS LG Multi-brand Remote Control Use the MODE button to select TV and put installer remote into TV operating mode. Notes: This remote is not supplied with the TV. This typical LG multi-brand remote control is shown for reference. Follow the instructions provided in the Installer menu section to configure the TV s features. INPUT TV INPUT MULTI POWER MODE TV DVD VCR WTCHING TV / CHNNEL CONTROL ll features shown may not be available on all TVs. TV INPUT/INPUT POWER MULTI MODE VOLUME UP/DOWN Select available input sources. Turns your TV or any other programmed equipment On or Off, depending on mode. Selects available auxiliary input sources. djusts picture brightness. Selects remote operating mode: TV, VCR, or DVD. Select these other operating modes for remote to operate external devices. Increases/decreases the sound level. EZ PIC EZ SOUND SWP INFO CC RTIO EXIT SP TIMER VOL CH PGE MUTE CHNNEL UP/DOWN/PGE TIMER MUTE NUMBER Buttons (0-9) (DSH) Selects available channels found with uto tuning. s to next available page. Sets the amount of time before the TV automatically turns itself Off. Switches the sound on or off. Use to enter a program number or channels. Dash for multiple channels such as 9-, 9-, etc FLSH BCK FLSHBK Returns to the previously viewed channel. 38

41 EZ PIC EZ SOUND SWP INFO Selects the factory preset picture appropriate for the viewing environment. Sets the appropriate sound for the program s content. Exchanges the main/sub images in Twin picture mode. While watching a TV program, will display program information on top of the screen. Info feature is not functional for ux sources. VCR/DVD BUTTONS CC EXIT RTIO SP Control some video cassette recorders or DVD players. ( RECORD is not functional in DVD mode.) Set up for VCR recording: Once, Regularly, Weekly, Off. ( RECORD button only). Brings up the main menu to the screen. s or exits a Panel Menu in the TV Guide on-screen menu system. Selects a closed caption option: Off, CC ~ 4, Text ~ 4. Clears all on-screen displays and returns to TV viewing from any TV menu. djusts the picture aspect ratio. Selects MTS sound: Mono, Stereo, and SP in nalog mode. Changes the audio language in DTV mode. WTCHING TV / CHNNEL CONTROL THUMBSTICK (Up/Down/Left Right/) Use to navigate on-screen menus / adjust the system settings to your requirements. Installing Batteries in Installer Remote Control + + Remove the battery compartment cover on the back side by sliding the cover downward until the batteries are exposed and can be removed. Install new batteries matching correct polarity as shown (+ with + and - with -). Slide cover back into position to close compartment. Install two high-quality.5v batteries. Never mix old or used batteries with new ones. Replace cover. 39

42 WTCHING TV / CHNNEL CONTROL TURNING ON TV First, connect power cord correctly. t this moment, the TV switches to standby mode. In standby mode to turn TV on, press the button on the TV or press the POWER button on the remote control. Note: Only for 3LG3DCH the TV also turn on with CH (+ or -) button on the remote. WTCHING TV / CHNNEL CONTROL 3! Select the viewing source by using the INPUT button on the remote control. This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. NOTE G If you intend to be away on vacation, disconnect the power plug from the wall power outlet. 40

43 CHNNEL SELECTION Press the CH (+ or -) or NUMBER buttons to select a channel number. VOLUME DJUSTMENT djust the volume to suit your personal preference. 3 Press the VOL (+ or -) button to adjust the volume. If you want to switch the sound off, press the MUTE button. You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button. WTCHING TV / CHNNEL CONTROL 4

44 WTCHING TV / CHNNEL CONTROL ON-SCREEN S SELECTION Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. CHNNEL PICTURE UDIO WTCHING TV / CHNNEL CONTROL uto Tuning Manual Tuning Channel Edit Channel Label spect Ratio : 6:9 Picture Mode : Standard Backlight 80 Contrast 90 Brightness 50 Sharpness 60 Color 60 Tint 0 E CHNNEL PICTURE TIME OPTION R UDIO LOCK G uto Volume : Off Clear Voice : On Balance 0 L Sound Mode : Standard SRS TruSurround XT: Off Treble 50 Bass 50 Reset E R TIME OPTION LOCK Clock : Feb//008/ :0 M Off Time : Off On Time : Off Sleep Timer : Off uto Sleep : Off Language Caption : English : Off Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block 3 4 Display each menu. Select a menu item. to the pop up menu. Return to TV viewing. 4

45 CHNNEL SETUP uto Scan (uto Tuning) utomatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run uto Tuning again after any ntenna/cable connection changes. CHNNEL uto Tuning Manual Tuning Channel Edit Channel Label Select CHNNEL. CHNNEL uto Tuning Manual Tuning Channel Edit Channel Label Press Yes button to begin auto tuning. Yes No WTCHING TV / CHNNEL CONTROL 3 4 Select uto Tuning. Select Yes. Run uto tuning. password is required to gain access to uto Tuning menu if the Lock System is turned on. 5 RETURN Return to the previous menu. Return to TV viewing. 43

46 WTCHING TV / CHNNEL CONTROL dd/delete Channel (Manual Tuning) If selecting DTV or CDTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received. CHNNEL CHNNEL WTCHING TV / CHNNEL CONTROL uto Tuning Manual Tuning Channel Edit Channel Label Select CHNNEL. uto Tuning Manual Tuning Channel Edit Channel Label F DIGITL G Select channel type and RF-channel number. Channel DIGITL - F G Bad Normal Good Delete Close Select Manual Tuning Select DIGITL or NLOG. Select channel you want to add or delete. Select dd or Delete. password is required to gain access to Manual Tuning menu if the Lock System is turned on. 6 RETURN Return to the previous menu. Return to TV viewing. 44

47 Channel Editing custom list can be created by toggling each channel on or off with button. The channels in the Custom List are displayed in black and the channels deleted from the Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to the small window at the topright corner of the screen. CHNNEL uto Tuning Manual Tuning Channel Edit Channel Label Select CHNNEL. dd/delete + CH Page Previous RETURN EXIT WTCHING TV / CHNNEL CONTROL Select Channel Edit. 3 Select a channel. 4 Select channel you want to add or delete. 5 Return to the previous menu. RETURN Return to TV viewing. 45

48 WTCHING TV / CHNNEL CONTROL CHNNEL LBEL Choose preset labels for your channels. If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn't preset a label for the channel. CHNNEL CHNNEL WTCHING TV / CHNNEL CONTROL uto Tuning Manual Tuning Channel Edit Channel Label Select CHNNEL. Select Channel Label. uto Tuning Manual Tuning Channel Edit Channel Label Channel DIGITL - Logo F Disney G Close 3 Select Channel. 4 Select a channel to set logo. 5 Select the appropriate logo for the channel. 6 RETURN Return to the previous menu. Return to TV viewing. 46

49 INPUT LIST TV V V Component RGB INPUT For 6/3LG3DCH 3LG3DC For LG3DCH Select the desired input source. TV V V HDMI RGB Component TV V WTCHING TV / CHNNEL CONTROL HDMI T V: Select it to watch over-the-air, cable and digital cable broadcasts. V-: Select them to watch a VCR or other external equipment. Component: Select them to watch DVD or a Digital set-top box. RGB: Select it to view PC input. HDMI: Select them to watch high definition devices. 47

50 PICTURE CONTROL PICTURE SIZE (SPECT RTIO) CONTROL This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV. RGB input source use 4:3 or 6:9 aspect ratio.! NOTE G If a fixed image is displayed on the screen for a long time, the image could become imprinted on the screen and remain visible. This phenomenon is rare on LCDs, but is possible when the image is on the screen for a very long time. This phenomenon is common to all manufacturers and is not covered by warranty. When watching video that does not fill the screen, any after-image from the black bars will normally dissipate after a few minutes. PICTURE CONTROL 6:9 RTIO RETURN Press the RTIO button repeatedly to select the picture options : Set By Program, 4:3, 6:9, Full(Only LG3DCH), Zoom, Zoom, Just Scan. Return to TV viewing. You can also adjust spect Ratio in the PICTURE menu. 48

51 Set by program Selects the proper picture proportion to match the source s image. (4:3 4:3) 6:9 djust the picture horizontally, in a linear proportion to fill the entire screen. (6:9 6:9) Full (Only LG3DCH) When TV receives the wide screen signal, it will lead you to adjust the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully. PICTURE CONTROL 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio. 49

52 PICTURE CONTROL PICTURE CONTROL Zoom Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. Zoom Choose Zoom when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage. Just Scan Normally the edges of video signals are cropped -%. Just Scan turns off this cropping and shows the complete video. Notes: If there is noise on the edges of the original signal, it will be visible when Just Scan is activated. Just Scan operates only with DTV/CDTV/HDMI-DTV/DVI-DTV (70p/080i/080p), Component(70p/080i) input sources. 50

53 PRESET PICTURE SETTINGS Picture Mode - Preset There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually. PICTURE Vivid Press the PICTURE button repeatedly to select the picture options : Vivid, Standard, Cinema, Sport, Game and Expert-. PICTURE CONTROL RETURN Return to TV viewing. You can also adjust Picture Mode in the PICTURE menu. 5

54 PICTURE CONTROL Color Tone - Preset Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. PICTURE PICTURE PICTURE CONTROL Brightness 50 Sharpness 50 Color 50 Tint 0 R dvanced Control Reset Screen (RGB-PC) E Contrast 50 G E Contrast 50 Brightness 50 Sharpness Color Temperature 50 F Medium G Color Fresh Contrast 50 Off Tint Fresh 0 R Color G Off dvanced Control Noise Reduction uto Reset Gamma Medium Screen (RGB-PC) Black Level Medium Real Cinema Off Close Select PICTURE. Select dvanced Control RETURN Select Color Temperature. Select Cool, Medium, or Warm. Return to the previous menu. Return to TV viewing. 5

55 MNUL PICTURE DJUSTMENT Picture Mode - User Mode djust the picture appearance to suit your preference and viewing situations. PICTURE spect Ratio : 6:9 Picture Mode : Standard Select PICTURE. Backlight 90 Contrast 90 Brightness 50 Sharpness 60 Color 60 Tint 0 R E G E Backlight 80 E E E PICTURE CONTROL Select Picture Mode RETURN Select Vivid, Standard, Cinema, Sport, or Game. Select Blacklight, Contrast, Brightness, Sharpness, Color, or Tint. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. 53

56 PICTURE CONTROL Picture Mode - Expert Control Expert and Expert allow you set you own custom settings. PICTURE CONTROL PICTURE spect Ratio : 6:9 Picture Mode : Standard Vivid Backlight Standard Contrast 90 Cinema Brightness 50 Sport Sharpness 60 Game Color 60 R G Expert Tint 0 E Expert Select PICTURE. PICTURE E Contrast 90 Fresh Contrast Brightness 50 Noise Reduction Sharpness 60 Gamma Color 60 Tint 0 Black Level Expert Control Real Cinema F Off G Off Medium uto Off Reset Color R Standard G HD Screen (RGB-PC) White Balance Normal Red Contrast 50 E RETURN Select Picture Mode. Select Expert or Expert. Select Expert Control. Select your desired menu option. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. 54

57 PICTURE IMPROVEMENT SETTINGS Fresh Contrast: Optimizes the contrast automatically according to the brightness of the reflection. Fresh Color: djusts the color of the reflection automatically to reproduce as close as possible natural colors. Noise Reduction: Removes interference up to the point where it does not damage the original picture. Gamma: High gamma values display whitish images and low gamma values display high contrast images. PICTURE PICTURE Brightness 50 Sharpness 50 Color 50 Tint 0 R dvanced Control Reset Screen (RGB-PC) E Contrast 50 G E Contrast 50 Brightness Color Temperature 50 F Medium G Sharpness 50 Fresh Contrast Color 50 Fresh Color F Off Off G Tint Noise 0 R ReductionG uto dvanced Control Gamma Medium Reset Black Level Medium Screen (RGB-PC) Real Cinema Off Close PICTURE CONTROL RETURN Select PICTURE. Select dvanced Control. Select Fresh Contrast, Fresh Color, Noise Reduction, or Gamma. Select your desired options. Return to the previous menu. Return to TV viewing. 55

58 PICTURE CONTROL DVNCED CONTROL - BLCK (DRKNESS) LEVEL djusting the contrast and the brightness of the screen using the black level of the screen. This feature is disable in DTV and RGB mode. PICTURE PICTURE PICTURE CONTROL Brightness 50 Sharpness 50 Color 50 Tint 0 R dvanced Control Reset Screen (RGB-PC) E Contrast 50 G E Contrast 50 Brightness 50Color Temperature Sharpness 50Fresh Contrast Color 50Fresh Color Tint 0 R G Noise Reduction dvanced Control Gamma Reset Black Level Screen (RGB-PC) Real Cinema Close Medium Off Off uto Medium F Low G Off RETURN Select PICTURE. Select dvanced Control. Select Black Level. Select Low or High. Return to the previous menu. Low: The reflection of the screen gets darker. High: The reflection of the screen gets brighter. uto: Realizing the black level of the screen and set it to High or Low automatically. Return to TV viewing. 56

59 DVNCED CONTROL - REL CINEM Set up the TV for the best picture appearance for viewing movies. When you operate Real Cinema (3: Pull-Down Mode or Cinema Correction Mode), the TV will adjust 4 fps video from movies to 30 fps video for display. This feature operates only in TV (nalog TV/CTV, Digital DTV/CDTV), V/V-, Component 480i/080i, and HDMI 480i/080i mode. PICTURE PICTURE Brightness 50 Sharpness 50 Color 50 Tint 0 R dvanced Control Reset Screen (RGB-PC) E Contrast 50 G E Contrast 50 Brightness Color Temperature 50 F Medium G Sharpness 50 Fresh Contrast Off Color 50 Fresh Color Off Tint 0 R Noise Reduction G uto dvanced Control Gamma Medium Reset Black Level Medium Screen (RGB-PC) Real Cinema F Off G Close PICTURE CONTROL 3 Select PICTURE. Select dvanced Control. Select Real Cinema. 4 5 RETURN Select O n or Off. Return to the previous menu. Return to TV viewing. 57

60 PICTURE CONTROL PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE PICTURE PICTURE CONTROL E Contrast 50 Brightness 50 Sharpness 50 Color 50 Tint 0 R dvanced Control Reset Screen (RGB-PC) Select PICTURE. G E Contrast 50 Brightness 50 Sharpness 50 i Resetting video configuration... Color 50 Tint 0 R dvanced Control Reset Screen (RGB-PC) G Select Reset. 3 Initialize the adjusted value. Return to TV viewing. 58

61 SOUND & LNGUGE CONTROL UTO VOLUME LEVELER (UTO VOLUME) uto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. UDIO uto Volume Clear Voice : Off : On UDIO uto Volume Clear Voice : Off Off : On On Balance 0 L R Balance 0 L R Sound Mode : Standard SRS TruSurround XT: Off Sound Mode : Standard SRS TruSurround XT: Off Treble 50 Treble 50 Bass 50 Bass 50 Reset Reset E E 3 4 RETURN Select UDIO. Select uto Volume. Select O n or Off. Return to the previous menu. SOUND & LNGUGE CONTROL Return to TV viewing. 59

62 SOUND & LNGUGE CONTROL CLER VOICE By differentiating the human sound range from others, it improves the sound quality of voices. UDIO UDIO uto Volume : Off uto Volume : Off Clear Voice : On Clear Voice : On Off Balance 0 L R Balance On 0 L R Sound Mode : Standard SRS TruSurround XT: Off Sound Mode : Standard SRS TruSurround XT: Off Treble 50 Treble 50 Bass 50 Bass 50 Reset Reset E E SOUND & LNGUGE CONTROL 3 4 RETURN Select UDIO. Select Clear Voice. Select O n or Off. Return to the previous menu. If you select Clear Voice-On, SRS TruSurround XT feature will not work. Return to TV viewing. 60

63 PRESET SOUND SETTINGS (SOUND MODE) Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content. Standard, Music, Cinema, Sport, and Game are preset for optimum sound quality at the factory and are not adjustable. Standard SOUND Press the SOUND button repeatedly to select the sound options : Standard, Music, Cinema, Sport, and Game. RETURN Return to TV viewing. SOUND & LNGUGE CONTROL You can also adjust Sound Mode in the UDIO menu. 6

64 SOUND & LNGUGE CONTROL SOUND SETTING DJUSTMENT - USER MODE djust the sound to suit your taste and room situations. UDIO UDIO uto Volume : Off uto Volume : Off Clear Voice : On Clear Voice : On Balance 0 L R Balance 0 L R Sound Mode : Standard SRS TruSurround XT: Off Sound Mode : Standard SRS TruSurround XT: SRS OffTruSurround XT Treble 50 Treble 50 Bass 50 Bass 50 Treble Bass Reset Reset E E Close E Off E SOUND & LNGUGE CONTROL 4 3 Select UDIO. Select Sound Mode. Select Standard, Music, Cinema, Sport, or Game. Select Treble or Bass. 5 Make appropriate adjustments. 6 RETURN Return to the previous menu. Return to TV viewing. 6

65 SRS TRUSURROUND XT Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement produces an immersive sound experience from standard stereo material. UDIO UDIO uto Volume : Off uto Volume : Off Clear Voice : On Clear Voice : On Balance 0 L R Balance 0 L R Sound Mode : Standard SRS TruSurround XT: Off Treble 50 Sound Mode : Standard SRS TruSurround XT: SRS OffTruSurround XT Treble 50 Treble 50 F Off G 3 Bass 50 Reset E Select UDIO. Select SRS TruSurround XT. Select O n or Off. Bass 50 Reset E Bass 50 Close SOUND & LNGUGE CONTROL 4 RETURN Return to the previous menu. Return to TV viewing. 63

66 SOUND & LNGUGE CONTROL BLNCE djust the left/right sound of speaker to suit your taste and room situations. UDIO UDIO uto Volume : Off uto Volume : Off Clear Voice : On Clear Voice : On Balance 0 L R Balance Balance 0 L 0 R L R Sound Mode : Standard SRS TruSurround XT: Off Sound Mode : Standard SRS TruSurround XT: OffClose Treble 50 Treble 50 Bass 50 Bass 50 Reset Reset E E E E SOUND & LNGUGE CONTROL 3 4 RETURN Select UDIO. Select Balance. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. 64

67 TV SPEKERS ON/OFF SETUP Turn the TV speakers off if using external audio equipment. UDIO UDIO Clear Voice : On E E Clear Voice : On Balance 0 L R Balance 0 L R Sound Mode : Standard SRS TruSurround XT: Off Sound Mode : Standard SRS TruSurround XT: Off Treble 50 Treble 50 Bass 50 Bass 50 Reset Reset TV Speaker : On TV Speaker : On Off On 3 4 RETURN Select UDIO. Select TV Speaker. Select O n or Off. Return to the previous menu. SOUND & LNGUGE CONTROL Return to TV viewing. 65

68 SOUND & LNGUGE CONTROL UDIO RESET Settings of the selected Sound Mode return to the default factory settings. UDIO UDIO uto Volume : Off uto Volume : Off Clear Voice : On Clear Voice : On Balance 0 L R Balance 0 L R Sound Mode : Standard SRS TruSurround XT: Off Sound Mode : Standard i Resetting audio configuration... SRS TruSurround XT: Off Treble 50 Treble 50 Bass 50 Bass 50 Reset Reset E E SOUND & LNGUGE CONTROL 3 Select UDIO. Select Reset. Initialize the adjusted value. 66

69 STEREO/SP BRODCST SETUP For nalog only: This TV can receive MTS stereo programs and any SP (Secondary udio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono. MONO STEREO SP SP RETURN Each time you press the SP button, Mono, Stereo, or SP appear in turn. Return to TV viewing. If other languages available on the digital signal, select them with the SP button. SOUND & LNGUGE CONTROL 67

70 SOUND & LNGUGE CONTROL UDIO LNGUGE Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV/CDTV mode. OPTION OPTION Language Caption : English : Off Language Caption : English : Off Menu English udio F English G Close SOUND & LNGUGE CONTROL RETURN Select OPTION. Select Language. Select udio. Select your desired language: English, Spanish, or French Return to the previous menu. Return to TV viewing. 68

71 ON-SCREEN S LNGUGE SELECTION The menus can be shown on the screen in the selected language. OPTION OPTION Language Caption : English : Off Language Caption : English : Off Menu F English G udio English Close 3 Select OPTION. Select Language. Select Menu. SOUND & LNGUGE CONTROL 4 5 RETURN Select your desired language. From this point on, the on-screen menus will be shown in the selected language. Return to the previous menu. Return to TV viewing. 69

72 SOUND & LNGUGE CONTROL CPTION MODE Caption must be provided to help people with hearing loss watch TV. This feature operates only in TV, V/V- mode. cc Select Caption O n or Off. When selecting Off, Sub-menus for nalog, DTV, and Digital Option become disabled. nalog Broadcasting System Captions Caption must be provided to help people with hearing loss watch TV. Select a caption mode for displaying captioning information if provided on a program. nalog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the ntenna/cable. SOUND & LNGUGE CONTROL OPTION Language Caption Select OPTION. : English : Off OPTION Language Caption : English : CC F On G Mode CC Digital Option Close RETURN Select Caption. Select O n. Select CC-4 or Text-4. Return to the previous menu. CPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. Return to TV viewing. 70

73 Digital Broadcasting System Captions Choose the language you want the DTV/CDTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On. OPTION OPTION Language Caption : English : Off Language Caption : English : CC F On G Mode CC Digital Option Close 3 Select OPTION. Select Caption. Select O n. SOUND & LNGUGE CONTROL 4 5 RETURN Select CC-4, Text-4, or Service - 6. Return to the previous menu. Return to TV viewing. 7

74 SOUND & LNGUGE CONTROL Caption Option Customize the DTV/CDTV captions that appear on your screen. This function in only available when Caption Mode is set On. OPTION OPTION F Custom G Language Caption : English : Off Language Caption : English : CC F On G Size Standard Font Font Mode CC Text Color White Digital Option Text Opacity Solid Bg Color Black Close Bg Opacity Solid Close SOUND & LNGUGE CONTROL Select OPTION. Select Caption. Select O n. Select Digital Option. Select Custom. Size: Set the word size. Font: Select a typeface for the text. Text Color: Choose a color for the text. Text Opacity: Specify the opacity for the text color. Bg ( Background) Color: Select a background color. Bg ( Background) Opacity: Select the opacity for the background color. 6 Customize the Style, Font, etc., to your preference. preview icon is provided at the bottom of the screen, use it to see the caption language. 7 RETURN Return to the previous menu. Return to TV viewing. 7

75 TIME SETTING CLOCK SETTING uto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function. TIME TIME Clock : Feb//008/ :0 M Off Time : Off On Time : Off Sleep Timer : Off uto Sleep : Off Clock : Feb//008/ F :0 M uto G Off Time : Off Year 008 On Time : Off Month Sleep Timer : Off Date uto Sleep : Off Hour M Minute 0 Time Zone Daylight Saving Eastern uto Close Select TIME. Select Clock. TIME SETTING RETURN Select uto. Select your viewing area time zone. : Eastern, Central, Mountain, Pacific, laska, or Hawaii. Select uto, O n, or O f f (depending on whether or not your viewing area observes Daylight Saving time). Return to the previous menu. Return to TV viewing. 73

76 TIME SETTING Manual Clock Setup If the current time setting is wrong, set the clock manually. TIME TIME Clock : Feb//008/ :0 M Off Time : Off On Time : Off Sleep Timer : Off uto Sleep : Off Clock : Feb//008/ :0 M F Manual G Off Time : Off Year 008 On Time : Off Month Sleep Timer : Off Date uto Sleep : Off Hour M Minute 0 Time Zone Daylight Saving Eastern uto Close TIME SETTING Select TIME. Select Clock. 3 4 Select Manual. Select the Year, Month, Date, Hour, or Minute option. 5 Set the Year, Month, Date, Hour, or Minute option. 6 RETURN Return to the previous menu. Return to TV viewing. 74

77 UTO ON/OFF TIME SETTING This function operates only if the current time has been set. The Off Time function overrides the On Time function if they are both set to the same time. The TV must be in standby mode for the On Time to work. TIME TIME Clock : Feb//008/ :0 M Off Time : Off On Time : Off Sleep Timer : Off uto Sleep : Off Clock : Feb//008/ :0 M Off Time : Off Repeat F Once G On Time : 6:30 M (Once) Hour 6 M Sleep Timer : Off Minute uto Sleep : Off 30 Close Select TIME. Select Off Time or On Time. TIME SETTING Select Repeat. Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Weekend, or Sunday. Select and set Hour or Minute. 6 RETURN Return to the previous menu. Return to TV viewing. 75

78 TIME SETTING SLEEP TIMER SETTING The Sleep Time turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. 0min TIME SETTING TIMER RETURN Press the TIMER button repeatedly to select the number of minutes. Sleep timer options: Off, 0, 0, 30, 60, 90, 0, 80, and 40 minutes. Return to TV viewing. You can also adjust Sleep Timer in the TIME menu. 76

79 UTO SHUT-OFF SETTING TV will be automatically turned off, in case of no signal for 0 minutes. TIME Clock Off Time On Time Sleep Timer : Off uto Sleep : Off : Feb//008/ :0 M : Off : Off TIME Clock Off Time On Time : Feb//008/ :0 M : Off : Off Sleep Timer : Off uto Sleep : Off Off On TV will be automatically turned off, in case of No Signal for 0 minutes. 3 Select TIME. Select uto Sleep. Select O n or Off. TIME SETTING 4 RETURN Return to the previous menu. Return to TV viewing. 77

80 PRENTL CONTROL / RTINGS Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done :. Set ratings and categories to be blocked.. Specify a password 3. Enable the lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-tovideo movies use the Movie Rating System (MP) only. Ratings for Television programs including made-for-tv movies : TV-G (General audience) TV-PG (Parental guidance suggested) TV-4 (Parents strongly cautioned) TV-M (Mature audience only) TV-Y (ll children) TV-Y7 (Children 7 years older) PRENTL CONTROL / RTINGS SET PSSWORD & LOCK SYSTEM Setting up Your Password Set up blocking schemes to block specific channels, ratings, and external viewing sources. password is required to gain access to this menu. LOCK Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Password * * * * Close Input the password. Select LOCK. the password as requested. The TV is set up with the initial password

81 Lock System Enables or disables the blocking scheme you set up previously. LOCK Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block : Off LOCK Lock System : On Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Off On Select LOCK RETURN Input the password. Select Lock System. Select O n or Off. Return to the previous menu. When you select O n, the Lock System is enable. PRENTL CONTROL / RTINGS Return to TV viewing. 79

82 PRENTL CONTROL /RTINGS Set Password Change the password by inputting a new password twice. LOCK LOCK Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block New * * * * Confirm * * * * Close Select LOCK. PRENTL CONTROL / RTINGS RETURN Input the password. Select Set password Choose any 4 digits for your new password. s soon as the 4 digits are entered, re-enter the same 4 digits on the Confirm. Return to the previous menu. Return to TV viewing. 80

83 CHNNEL BLOCKING Blocks any channels that you do not want to watch or that you do not want your children to watch. LOCK Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Block/Unblock CH + Page Previous RETURN EXIT Select LOCK Input the password. Select Block Channel. Select a channel to block or unblock. Block or unblock a channel. Return to the previous menu. PRENTL CONTROL / RTINGS RETURN Return to TV viewing. 8