"shell" digital storage oscilloscope (Beta)

Size: px
Start display at page:

Download ""shell" digital storage oscilloscope (Beta)"

Transcription

1 "shell" digital storage oscilloscope (Beta) 1. Main board: solder the element as the picture shows: 2. 1) Check the main board is normal or not Supply 9V power supply through the connector J7 (Note: The connector center conductor is positive), the main control board to see whether the normal start, if the board is normal start, LCD screen will display the product model, software version, the oscilloscope's main working interface, as shown in Figure 2.

2 -Figure 2 If the LCD display is not normal, or the circuit board has significant heat, smoke and other phenomena, please immediately power off, recording and notification service vendors. 2) Assembly step After the MPU test normal, disconnect the power, then follow the steps below for assembly, first of all, soldering the backside element of LCD screen, then soldering the same side element of LCD screen. a. Soldering test signal output terminal J8, two feet bents 90 degrees, and then soldered to the board. b. Soldering backup power input J6. c. Soldering power supply switch SW5. d. At the same side of the screen soldering switches SW1, SW2, SW3 and SW4. E. Remove the resistor R30. R30 is a 0 ohm resistor, it is actually used for the power switch SW5 short-circuited, so that when the power switch SW5 is not yet installed can be energized to check, after the installation of SW5, R30 should be removed, so that SW5 can function properly. 3. Check the results of the assembly After the above installation steps, turn the power on, check whether the power switch is working properly, check 4 Press key is working properly. 4. Analog board assembly Analog board assembly sequence according to component height from low to high principle, specific assembly steps are as follows:

3 1) Resistance soldering. According to the resistance label material checklist printed on the PCB (see below) to find the appropriate resistor values, confirm the resistance with a multimeter; then bent the legs in the same direction, and the distance between the legs are about 8mm; soldering all ring resistances one by one. 2) Soldering ceramic capacitors C1, C2, C4, C6, C7. 3) Install a trimmer capacitor C3 and C5. 4) Install toggle switch SW1. 5) Install the electrolytic capacitors C10 - C14. 6) Install BNC connector J1. Note: Beta version's analog channels have a design error in which a wire missing, the need to manually fill, the method is to use a approximately 3cm short-wire connect R22 (near the BNC connector) with R24 (near the trimmer capacitor C5) Check as the FIG.3

4 5. Debugging FIG.3 Before power-on test, carefully check the soldering of all components as much as possible exclude the possibility of false soldering or short circuit, the circuit board and clean residual rosin solder, and then follow the steps below test debugging. 1) Set the POWER switch to the OFF position (ie, near the power outlet J7 position), then connect the power supply to the main circuit board J7 (or J6), switches the power switch SW5 to ON position, check the oscilloscope is normal start or not. If the screen displays normal, operates four buttons and rotary switch, check the reaction on the screen properly normal or not.

5 2) If the above tests are normal, then switches the power to the OFF position, then connects the double-pin J3 and row socket J4 on the main board, pay attention to the direction of the connection, as Figure 4 show: Figure 4. 3) Switches the power SW5 to ON position, watching the screen showed no abnormalities, if not then check the voltage, detecting point marked in the backside of the PCB, the normal value shown in the table: Test point label Normal voltage value Support Mix. Support Max. Specification AV+ 7.0V +5.5V +8.5V Input +9V AV- -6.5V -9.0V -5.0V Input +9V V5-1.0V -1.2V -0.8V 4) Put the coupling swith SW1 to GND, measure the following voltage: Normal voltage Test point label Support Mix. Support Max. Specification value V1 0V -0.1V +0.1V The coupling switch SW1 in

6 V2 0V -0.1V +0.1V the GND position V3 0V -0.1V +0.1V V4 +1.6V +1.3V +1.9V 6. Adjust the compensation capacitor C3 and C5 Adjustment C5: 1) Connect the probe and the BNC connector J1, and use the clip clamping the output terminal J8, black clip can be vacant (Fig. 5). 2) Set the scope parameter to the value shown in Fig. 5 screen, and adjust the trigger level to make the waveform stable. 3) Use a small screwdriver to adjust the C5, make the square wave-shaped angle is the best angle. Adjustment C3: FIG. 5 1) Between the test signal output terminal and ground connects a 20-30

7 ohm resistor (Figure 6), so that the test signal amplitude is reduced to approximately 0.1V (Note: This display value is only an approximation, the actual value is 0.1V V, does not affect the adjustment). 2) Set the oscilloscope parameter to the as shown in FIG. 7, and adjust the trigger level to make the waveform stable. 3) Use a small screwdriver to adjust the C5, make the square wave-shaped angle is the best angle Commissioning is complete.

DSO138mini Troubleshooting Guide

DSO138mini Troubleshooting Guide DSO138mini Troubleshooting Guide Applicable main board: 109-13800-00I Applicable analog board: 109-13801-00H 1. Frequently Found Problems 1) LCD completely dark. No backlight 2) LCD lights up but no display

More information

Quick Start. RSHS1000 Series Handheld Digital Oscilloscope

Quick Start. RSHS1000 Series Handheld Digital Oscilloscope Quick Start RSHS1000 Series Handheld Digital Oscilloscope General Safety Summary Carefully read the following safety precautions to avoid personal injury and prevent damage to the instrument or any products

More information

S op o e p C on o t n rol o s L arni n n i g n g O bj b e j ctiv i e v s

S op o e p C on o t n rol o s L arni n n i g n g O bj b e j ctiv i e v s ET 150 Scope Controls Learning Objectives In this lesson you will: learn the location and function of oscilloscope controls. see block diagrams of analog and digital oscilloscopes. see how different input

More information

Beginners How to Test DSO138mini

Beginners How to Test DSO138mini Beginners How to Test DSO138mini You have finished assembling your DSO138mini kit. You may be anxious to see it works. But you might not be familiar with oscilloscope and you could encounter unexpected

More information

DIY KIT MHZ 8-DIGIT FREQUENCY METER

DIY KIT MHZ 8-DIGIT FREQUENCY METER This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).

More information

Documentation VFD clock 8 a clock

Documentation VFD clock 8 a clock Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success

More information

Experiment # 4 Counters and Logic Analyzer

Experiment # 4 Counters and Logic Analyzer EE20L - Introduction to Digital Circuits Experiment # 4. Synopsis: Experiment # 4 Counters and Logic Analyzer In this lab we will build an up-counter and a down-counter using 74LS76A - Flip Flops. The

More information

Quick Start. SHS1000 Series Handheld Digital Oscilloscope QS03010-E02B 2015 SIGLENT TECHNOLOGIES CO., LTD

Quick Start. SHS1000 Series Handheld Digital Oscilloscope QS03010-E02B 2015 SIGLENT TECHNOLOGIES CO., LTD Quick Start SHS1000 Series Handheld Digital Oscilloscope QS03010-E02B 2015 SIGLENT TECHNOLOGIES CO., LTD Guaranty and Declaration Copyright SIGLENT TECHNOLOGIES CO., LTD. All Rights Reserved. Trademark

More information

VU Meter Buffer DIY Kit

VU Meter Buffer DIY Kit VU Meter Buffer DIY Kit Warning This document is distributed for educational purposes only. This equipment operates at potentially lethal voltages. Only trained, qualified personnel should operate, maintain,

More information

Total solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL

Total solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL Total solder points: 123 Difficulty level: beginner 1 2 3 4 5 advanced AUDIO ANALYZER K8098 ra audio gea Give your. look high-tech ILLUSTRATED ASSEMBLY MANUAL H8098IP-1 Features & Specifications Features

More information

DL-1A. RF dummy load - 50Ω 20W. Assembly manual. Last update: May 1, Thank you for constructing the DL-1A dummy load kit

DL-1A. RF dummy load - 50Ω 20W. Assembly manual. Last update: May 1, Thank you for constructing the DL-1A dummy load kit DL-1A RF dummy load - 50Ω 20W Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thank you for constructing the DL-1A dummy load kit Have fun assembling it

More information

Using an oscilloscope - The Hameg 203-6

Using an oscilloscope - The Hameg 203-6 Using an oscilloscope - The Hameg 203-6 What does an oscilloscope do? Setting up How does an oscilloscope work? Other oscilloscope controls Connecting a function generator Microphones audio signals and

More information

How to overcome/avoid High Frequency Effects on Debug Interfaces Trace Port Design Guidelines

How to overcome/avoid High Frequency Effects on Debug Interfaces Trace Port Design Guidelines How to overcome/avoid High Frequency Effects on Debug Interfaces Trace Port Design Guidelines An On-Chip Debugger/Analyzer (OCD) like isystem s ic5000 (Figure 1) acts as a link to the target hardware by

More information

Bill of Materials: Super Simple Water Level Control PART NO

Bill of Materials: Super Simple Water Level Control PART NO Super Simple Water Level Control PART NO. 2169109 Design a simple water controller in which electrodes are required to sense high and low water levels in a tank. Whenever the water level falls below the

More information

NewScope-7A Operating Manual

NewScope-7A Operating Manual 2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3

More information

Connection Guide of the MOTOTRBO radio to the radioserver as a control station

Connection Guide of the MOTOTRBO radio to the radioserver as a control station of the MOTOTRBO radio to the radioserver as a control station (using the PMKN4147A programming cable and a cable with the HLN9457 connector) August 2015 2 1 Introduction This guide explains how to connect

More information

Physics 123 Hints and Tips

Physics 123 Hints and Tips Physics 123 Hints and Tips Solderless Breadboards All of the analog labs and most of the digital labs will be built on the Proto-Board solderless breadboards. These provide three solderless breadboard

More information

Introduction 1. Green status LED, controlled by output signal ST. Sounder, controlled by output signal Q6. Push switch on input D6

Introduction 1. Green status LED, controlled by output signal ST. Sounder, controlled by output signal Q6. Push switch on input D6 Introduction 1 Welcome to the GENIE microcontroller system! The activity kit allows you to experiment with a wide variety of inputs and outputs... so why not try reading sensors, controlling lights or

More information

TECHNOLOGY WILL SAVE US: THE LUMIPHONE

TECHNOLOGY WILL SAVE US: THE LUMIPHONE TECHNOLOGY WILL SAVE US: THE LUMIPHONE This is a step-by-step guide to soldering your own Lumiphone. The equipment you should have at your station: goggles, soldering mat, soldering Iron, solder and side

More information

Connection Guide of the MOTOTRBO radio to the radioserver as a control station

Connection Guide of the MOTOTRBO radio to the radioserver as a control station of the MOTOTRBO radio to the radioserver as a control station (using the PMKN447A programming cable and a cable with the HLN9457 connector) March 207 2 Introduction This guide explains how to prepare a

More information

Nixie Clock Type Frank 2 Z570M

Nixie Clock Type Frank 2 Z570M Assembly Instructions And User Guide Nixie Clock Type Frank 2 Z570M Software version: 7R PCB Revision: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 2 is a compact design with

More information

NON-OVERSAMPLING DIGITAL TO ANALOG CONVERTER ASSEMBLY INSTRUCTIONS FEATURES DESCRIPTION JUNDAC FIVE

NON-OVERSAMPLING DIGITAL TO ANALOG CONVERTER ASSEMBLY INSTRUCTIONS FEATURES DESCRIPTION JUNDAC FIVE NON-OVERSAMPLING DIGITAL TO ANALOG CONVERTER ASSEMBLY INSTRUCTIONS July 2011 - Rev 1.0, Eric Juaneda - www.junilabs.com FEATURES ONE DIGITAL INPUT S/PDIF, AES3 DIGITAL TRANSFORMER INPUT RCA, BNC or XLR

More information

XTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors

XTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only

More information

ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT

ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT BUILD INSTRUCTIONS Before you start take a look at the Printed Circuit Board (PCB). The components go in the side with the writing on

More information

Nixie Clock Type Frank 3

Nixie Clock Type Frank 3 Assembly Instructions And User Guide Nixie Clock Type Frank 3 Software version: 7R PCB Version: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 3 is a compact design with all

More information

Working with a Tektronix TDS 3012B Oscilloscope EE 310: ELECTRONIC CIRCUIT DESIGN I

Working with a Tektronix TDS 3012B Oscilloscope EE 310: ELECTRONIC CIRCUIT DESIGN I Working with a Tektronix TDS 3012B Oscilloscope EE 310: ELECTRONIC CIRCUIT DESIGN I Prepared by: Kyle Botteon Questions? kyle.botteon@psu.edu 2 Background Information Recall that oscilloscopes (scopes)

More information

Build A Video Switcher

Build A Video Switcher Build A Video Switcher VIDEOSISTEMAS serviciotecnico@videosistemas.com www.videosistemas.com Reprinted with permission from Electronics Now Magazine September 1997 issue Copyright Gernsback Publications,

More information

SWITCH: Microcontroller Touch-switch Design & Test (Part 2)

SWITCH: Microcontroller Touch-switch Design & Test (Part 2) SWITCH: Microcontroller Touch-switch Design & Test (Part 2) 2 nd Year Electronics Lab IMPERIAL COLLEGE LONDON v2.09 Table of Contents Equipment... 2 Aims... 2 Objectives... 2 Recommended Timetable... 2

More information

N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012

N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 Kit properly assembled and configured for Standard Serial LCD (LCD Not yet connected) Kit Components Item Qty Designator Part Color/Marking

More information

4.9 BEAM BLANKING AND PULSING OPTIONS

4.9 BEAM BLANKING AND PULSING OPTIONS 4.9 BEAM BLANKING AND PULSING OPTIONS Beam Blanker BNC DESCRIPTION OF BLANKER CONTROLS Beam Blanker assembly Electron Gun Controls Blanker BNC: An input BNC on one of the 1⅓ CF flanges on the Flange Multiplexer

More information

N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB

N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB Kit Components Item Qty Designator Part Color/Marking PCB 1 LCD Display 1 LCD 1602 Volt Regulator 1 U1 78L05, Black TO-92 Prescaler

More information

ELECTRICAL ENGINEERING DEPARTMENT California Polytechnic State University

ELECTRICAL ENGINEERING DEPARTMENT California Polytechnic State University EECTRICA ENGINEERING DEPARTMENT California Polytechnic State University EE 361 NAND ogic Gate, RS Flip-Flop & JK Flip-Flop Pre-lab 7 1. Draw the logic symbol and construct the truth table for a NAND gate.

More information

DDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1

DDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1 DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1.1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be

More information

REGO Start&Go USER MANUAL

REGO Start&Go USER MANUAL REGO Start&Go USER MANUAL Version 0 Rev. B of 03/03/16 Page 1 of 15 Introduction The purpose of the manual is to describe all of the steps required to commission and correctly operate the REGO Start&Go

More information

LABORATORY # 1 LAB MANUAL. Digital Signals

LABORATORY # 1 LAB MANUAL. Digital Signals Department of Electrical Engineering University of California Riverside Laboratory #1 EE 120 A LABORATORY # 1 LAB MANUAL Digital Signals 2 Objectives Lab 1 contains 3 (three) parts and the objectives are

More information

Laboratory 10. Required Components: Objectives. Introduction. Digital Circuits - Logic and Latching (modified from lab text by Alciatore)

Laboratory 10. Required Components: Objectives. Introduction. Digital Circuits - Logic and Latching (modified from lab text by Alciatore) Laboratory 10 Digital Circuits - Logic and Latching (modified from lab text by Alciatore) Required Components: 1x 330 resistor 4x 1k resistor 2x 0.F capacitor 1x 2N3904 small signal transistor 1x LED 1x

More information

Basic LabVIEW Programming Amit J Nimunkar, Sara Karle, Michele Lorenz, Emily Maslonkowski

Basic LabVIEW Programming Amit J Nimunkar, Sara Karle, Michele Lorenz, Emily Maslonkowski Introduction This lab familiarizes you with the software package LabVIEW from National Instruments for data acquisition and virtual instrumentation. The lab also introduces you to resistors, capacitors,

More information

Solutions to Embedded System Design Challenges Part II

Solutions to Embedded System Design Challenges Part II Solutions to Embedded System Design Challenges Part II Time-Saving Tips to Improve Productivity In Embedded System Design, Validation and Debug Hi, my name is Mike Juliana. Welcome to today s elearning.

More information

MONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS

MONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS MONO AMPLIFIER KIT Version 2.2 Build Instructions

More information

Reaction Game Kit MitchElectronics 2019

Reaction Game Kit MitchElectronics 2019 Reaction Game Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Schematic 3 How It Works 4 Materials 6 Construction 8 Important Information 9 Page 2 SCHEMATIC Page 3 SCHEMATIC EXPLANATION The

More information

Building the BX24-AHT

Building the BX24-AHT Building the BX24-AHT file:///f /LASER/build-it.htm (1 of 8) [03/04/2002 5:21:52 PM] file:///f /LASER/build-it.htm (2 of 8) [03/04/2002 5:21:52 PM] Tips & Tricks Use a 25W or smaller soldering iron with

More information

Nixie Tube Clock Type Marsden

Nixie Tube Clock Type Marsden Assembly Instructions And User Guide Nixie Tube Clock Type Marsden Software version: RTC-1.3 PCB Revision: 16 Aug 10-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Marsden is a compact design

More information

SPECIFICATION SFW056XU1-AV

SPECIFICATION SFW056XU1-AV Version:2.0 Customer Approved Customer SPECIFICATION SFW056XU1-AV Date By Sunful s Confirmation Approved By Prepared By Date: 2005.1.10-1 - CONTENTS General Description..3 Features.3 Applications 3 Driving

More information

INTRODUCTION (EE2499_Introduction.doc revised 1/1/18)

INTRODUCTION (EE2499_Introduction.doc revised 1/1/18) INTRODUCTION (EE2499_Introduction.doc revised 1/1/18) A. PARTS AND TOOLS: This lab involves designing, building, and testing circuits using design concepts from the Digital Logic course EE-2440. A locker

More information

Video Streamer Modifications

Video Streamer Modifications CB Electronics Video Streamer Modifications CB Electronics Loddonside, Lands End House, Beggars Hill Road, Charvil, Berks RG10 0UD, UK Tel: +44 (0)118 9320345, Fax: +44 (0)118 9320346 URL: www.colinbroad.com

More information

Laboratory 11. Required Components: Objectives. Introduction. Digital Displays and Logic (modified from lab text by Alciatore)

Laboratory 11. Required Components: Objectives. Introduction. Digital Displays and Logic (modified from lab text by Alciatore) Laboratory 11 Digital Displays and Logic (modified from lab text by Alciatore) Required Components: 2x lk resistors 1x 10M resistor 3x 0.1 F capacitor 1x 555 timer 1x 7490 decade counter 1x 7447 BCD to

More information

BME 3512 Biomedical Laboratory Equipment List

BME 3512 Biomedical Laboratory Equipment List BME 3512 Biomedical Laboratory Equipment List Agilent E3630A DC Power Supply Agilent 54622A Digital Oscilloscope Agilent 33120A Function / Waveform Generator APPA 95 Digital Multimeter Component Layout

More information

LOOK AT THE NETWORK OF METAL STRIPS ON THE BACKSIDE OF THE PROTOTYPING BOARD

LOOK AT THE NETWORK OF METAL STRIPS ON THE BACKSIDE OF THE PROTOTYPING BOARD Circuit Prototyping OBJECTIVES In this lab you will create a prototype of an electronic speed sensor that you will use to measure the speed of the roller coaster ball on your roller coaster. The lab has

More information

Burlington County College INSTRUCTION GUIDE. for the. Hewlett Packard. FUNCTION GENERATOR Model #33120A. and. Tektronix

Burlington County College INSTRUCTION GUIDE. for the. Hewlett Packard. FUNCTION GENERATOR Model #33120A. and. Tektronix v1.2 Burlington County College INSTRUCTION GUIDE for the Hewlett Packard FUNCTION GENERATOR Model #33120A and Tektronix OSCILLOSCOPE Model #MSO2004B Summer 2014 Pg. 2 Scope-Gen Handout_pgs1-8_v1.2_SU14.doc

More information

Assembly Instructions And User Guide. Nixie FunKlock. FunKlock Issue 4 (1 February 2017)

Assembly Instructions And User Guide. Nixie FunKlock. FunKlock Issue 4 (1 February 2017) Assembly Instructions And User Guide Nixie FunKlock - 1 - Issue Number Date REVISION HISTORY 4 1 February 2017 New diode for D2 3 27 December 2013 C7 / C8 error page 15 2 7 November 2013 Errors corrected

More information

HMC958LC5 HIGH SPEED LOGIC - SMT. Typical Applications. Features. Functional Diagram. General Description

HMC958LC5 HIGH SPEED LOGIC - SMT. Typical Applications. Features. Functional Diagram. General Description Typical Applications Features The HMC958LC5 is ideal for: SONET OC-192 and 1 GbE 16G Fiber Channel 4:1 Multiplexer Built-In Test Broadband Test & Measurement Functional Diagram Supports High Data Rates:

More information

Main PCB (The small one)

Main PCB (The small one) Thanks for choosing our kits! This manual is written taking with the problems that we usually find in our workshops in mind. Also the order is meant to make assembly as easy as possible. Some steps are

More information

Multi-Key v2.4 Multi-Function Amplifier Keying Interface

Multi-Key v2.4 Multi-Function Amplifier Keying Interface Multi-Key v2.4 Multi-Function Amplifier Keying Interface ASSEMBLY & OPERATION INSTRUCTIONS INTRODUCTION The Harbach Electronics, LLC Multi-Key is a multi-function external device designed for the safe

More information

KHT 1000C HV-Probe Calibrator. Instruction Manual

KHT 1000C HV-Probe Calibrator. Instruction Manual KHT 1000C HV-Probe Calibrator Instruction Manual Copyright 2015 PMK GmbH All rights reserved. Information in this publication supersedes that in all previously published material. Specifications are subject

More information

Lab 7: Soldering - Traffic Light Controller ReadMeFirst

Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two-way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been

More information

Laboratory 8. Digital Circuits - Counter and LED Display

Laboratory 8. Digital Circuits - Counter and LED Display Laboratory 8 Digital Circuits - Counter and Display Required Components: 2 1k resistors 1 10M resistor 3 0.1 F capacitor 1 555 timer 1 7490 decade counter 1 7447 BCD to decoder 1 MAN 6910 or LTD-482EC

More information

Exercise 2: Connecting the Digital Logic Circuits

Exercise 2: Connecting the Digital Logic Circuits Exercise 2: Connecting the Digital Logic Circuits EXERCISE OBJECTIVE When you have completed this exercise, you will be able to connect digital logic circuits and observe the inputs and outputs by using

More information

Owners SW-LCD 2.0 Manual & Specifications

Owners SW-LCD 2.0 Manual & Specifications Owners SW-LCD 2.0 Manual & Specifications Contents 1. Preface. 19 2. Appearance and Size.20 2.1 Material and Color 20 2.2 Display Size and Installation Size 20 3. Function Summary and Button Definition

More information

VU-1 VU Meter Kit Volume Unit Meter

VU-1 VU Meter Kit Volume Unit Meter VU-1 VU Meter Kit Volume Unit Meter Simplicity Counts, Detail Matters. No part of this document may be reproduced, either mechanically or electronically, posted online on the Internet, in whole or in part,

More information

DOGM GRAPHIC SERIES 128x64 DOTS

DOGM GRAPHIC SERIES 128x64 DOTS DOGM GRAPHIC SERIES 128x64 DOTS 27.6.2007 available from 1 pc. off! flat: 5.6mm incl. LED TECHNICAL DATA EA DOGM128W-6 + EA LED55x46-A EA DOGM128B-6 + EA LED55x46-W EA DOGM128W-6 + EA LED55x46-W * HIGH-CONTRAST

More information

Modellbahn Digital Peter Stärz

Modellbahn Digital Peter Stärz Modellbahn Digital Peter Stärz Dresdener Str. 68 D-02977 Hoyerswerda +49 3571 404027 www.firma-staerz.de info@firma-staerz.de 8-fold Track Occupancy Detector for digital systems with two-wire track (e.g.

More information

GUIDE TO ASSEMBLY OF ERICA SYNTHS DELAY MODULE

GUIDE TO ASSEMBLY OF ERICA SYNTHS DELAY MODULE If you are reading this, most probably, you are about to build Erica Synths DIY DELAY module. The module is 4mm deep, skiff friendly, has solid mechanical construction and doesn t require wiring. Erica

More information

Introduction 1. Green status LED, controlled by output signal ST

Introduction 1. Green status LED, controlled by output signal ST Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away

More information

DA IN 1-OUT LINE DRIVER WITH EQUALIZATION + AUDIO USER S GUIDE

DA IN 1-OUT LINE DRIVER WITH EQUALIZATION + AUDIO USER S GUIDE MANUAL PART NUMBER: 400-0430-001 1-IN 1-OUT LINE DRIVER WITH UALIZATION + AUDIO USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL...2 GUIDELINES FOR RACK-MOUNTING...2 INSTALLATION...2

More information

Introduction 1. Digital inputs D6 and D7. Battery connects here (red wire to +V, black wire to 0V )

Introduction 1. Digital inputs D6 and D7. Battery connects here (red wire to +V, black wire to 0V ) Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away

More information

ME EN 363 ELEMENTARY INSTRUMENTATION Lab: Basic Lab Instruments and Data Acquisition

ME EN 363 ELEMENTARY INSTRUMENTATION Lab: Basic Lab Instruments and Data Acquisition ME EN 363 ELEMENTARY INSTRUMENTATION Lab: Basic Lab Instruments and Data Acquisition INTRODUCTION Many sensors produce continuous voltage signals. In this lab, you will learn about some common methods

More information

University of Utah Electrical & Computer Engineering Department ECE1050/1060 Oscilloscope

University of Utah Electrical & Computer Engineering Department ECE1050/1060 Oscilloscope University of Utah Electrical & Computer Engineering Department ECE1050/1060 Oscilloscope Name:, A. Stolp, 2/2/00 rev, 9/15/03 NOTE: This is a fill-in-the-blanks lab. No notebook is required. You are encouraged

More information

Oscilloscope Guide Tektronix TDS3034B & TDS3052B

Oscilloscope Guide Tektronix TDS3034B & TDS3052B Tektronix TDS3034B & TDS3052B Version 2008-Jan-1 Dept. of Electrical & Computer Engineering Portland State University Copyright 2008 Portland State University 1 Basic Information This guide provides basic

More information

GEKCO SUBCARRIER REFERENCE OSCILLATOR MODEL SRO10 OPERATION/SERVICE MANUAL

GEKCO SUBCARRIER REFERENCE OSCILLATOR MODEL SRO10 OPERATION/SERVICE MANUAL GEKCO MODEL SRO10 SUBCARRIER REFERENCE OSCILLATOR OPERATION/SERVICE MANUAL GEKCO Labs PO Box 642 Issaquah, WA 98027 (425) 392-0638 P/N 595-431 REV 5/98 Copyright c 1998 GEKCO Labs All Rights Reserved Printed

More information

MAIN PCB (The small one) OPEN MAIN BOARD BAG A

MAIN PCB (The small one) OPEN MAIN BOARD BAG A THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed

More information

MBUS 10 RS232 TO MBUS LEVEL CONVERTER

MBUS 10 RS232 TO MBUS LEVEL CONVERTER Media and protocol converters MBUS 10 RS232 TO MBUS LEVEL CONVERTER RS232 to MBus level conversion Maximum 10 MBus slaves Baud Rate: 300 to 19200 bps RS232 MBus opto isolation Over-current and short-circuit

More information

imso-104 Manual Revised August 5, 2011

imso-104 Manual Revised August 5, 2011 imso-104 Manual Revised August 5, 2011 Section 1 Getting Started SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 How it works 2.10 Menus 2.20 Analog Channel

More information

EPROM pattern generator with "Genlock"

EPROM pattern generator with Genlock EPROM pattern generator with "Genlock" This generator uses an EPROM to store several pictures that can then be selected by means of a thumb-wheel switch. Alternatively, if the pictures stored are in a

More information

Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009

Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009 Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that

More information

ECB DIGITAL ELECTRONICS PROJECT BASED LEARNING PROJECT REPORT ON 7 SEGMENT DIGITAL STOP WATCH USING DECODER

ECB DIGITAL ELECTRONICS PROJECT BASED LEARNING PROJECT REPORT ON 7 SEGMENT DIGITAL STOP WATCH USING DECODER ECB2212 - DIGITAL ELECTRONICS PROJECT BASED LEARNING PROJECT REPORT ON 7 SEGMENT DIGITAL STOP WATCH USING DECODER SUBMITTED BY ASHRAF HUSSAIN (160051601105) S SAMIULLAH (160051601059) CONTENTS >AIM >INTRODUCTION

More information

This Unit may form part of a National Qualification Group Award or may be offered on a free standing basis.

This Unit may form part of a National Qualification Group Award or may be offered on a free standing basis. National Unit Specification: general information CODE F5JJ 11 SUMMARY The Unit is intended for candidates with little or no prior knowledge of Analogue or Digital Electronic Circuits. It provides an opportunity

More information

COLOUR CHANGING USB LAMP KIT

COLOUR CHANGING USB LAMP KIT TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE SEE AMAZING LIGHTING EFFECTS WITH THIS COLOUR CHANGING USB LAMP KIT Version 2.1 Index of Sheets TEACHING

More information

Lab 7: Soldering - Traffic Light Controller ReadMeFirst

Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been

More information

Tube Cricket Build Guide

Tube Cricket Build Guide Tube Cricket Build Guide The Tube Cricket is a small-wattage amp that puts out about 1 watt of audio power. With a 12AU7 tube-preamp and a JRC386 power amp, the Tube Cricket gives you great tone in a compact

More information

Exercise 2: D-Type Flip-Flop

Exercise 2: D-Type Flip-Flop Flip-Flops Digital Logic Fundamentals Exercise 2: D-Type Flip-Flop EXERCISE OBJECTIVE When you have completed this exercise, you will be able to determine the characteristics of a D-type results with an

More information

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT /12/14 BIT 10 TO 65 MSPS DUAL ADC

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT /12/14 BIT 10 TO 65 MSPS DUAL ADC LTC2286, LTC2287, LTC2288, LTC2290, LTC2291, LTC2292, LTC2293, LTC2294, LTC2295, LTC2296, LTC2297, LTC2298 or LTC2299 DESCRIPTION Demonstration circuit 816 supports a family of s. Each assembly features

More information

8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT BOARD)

8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT BOARD) ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS LEARN ABOUT PROGRAMMING WITH THIS 8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT

More information

Step What to do Expected result What to do if test fails Component tested 1 Visual inspection. Board is accurately assembled

Step What to do Expected result What to do if test fails Component tested 1 Visual inspection. Board is accurately assembled Fox Delta Amateur Radio Projects & Kits AAZ-0914A 50MHZ Antenna Analyzer Testing Guide by Tony / I2TZK SWR Analyzer 4 steps for a quick test Step What to do Expected result What to do if test fails Component

More information

Expect to Make Waves.

Expect to Make Waves. Expect to Make Waves. The New Oscilloscope Large 10.4" LCD touch screen Long capture time Extensive communication capabilities www.lecroy.com The New Oscillos From its large 10.4" LCD touch screen to its

More information

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT /12/14 BIT 10 TO 105 MSPS ADC

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT /12/14 BIT 10 TO 105 MSPS ADC LTC2280, LTC2282, LTC2284, LTC2286, LTC2287, LTC2288 LTC2289, LTC2290, LTC2291, LTC2292, LTC2293, LTC2294, LTC2295, LTC2296, LTC2297, LTC2298 or LTC2299 DESCRIPTION Demonstration circuit 851 supports a

More information

PB-507. Advanced Analog & Digital Electronic Design Workstation Instruction Manual. Revision: 2/2014

PB-507. Advanced Analog & Digital Electronic Design Workstation Instruction Manual. Revision: 2/2014 PB-507 Advanced Analog & Digital Electronic Design Workstation Instruction Manual Revision: 2/2014 Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com 1 1

More information

SUNSTAR 微波光电 TEL: FAX: v HMC750LP4 / 750LP4E 12.5 Gbps LIMITING AMPLIFIER

SUNSTAR 微波光电   TEL: FAX: v HMC750LP4 / 750LP4E 12.5 Gbps LIMITING AMPLIFIER Typical Applications The HMC75LP4(E) is ideal for: OC-192 Receivers Gbps Ethernet Receivers Gbps Fiber Channel Receivers Broadband Test & Measurement Functional Diagram Features Electrical Specifications,

More information

r.link Video-inserter RL5-UCON7-500 Compatible with Fiat vehicles with Uconnect 7inch infotainment

r.link Video-inserter RL5-UCON7-500 Compatible with Fiat vehicles with Uconnect 7inch infotainment r.link Video-inserter RL5-UCON7-500 Compatible with Fiat vehicles with Uconnect 7inch infotainment Video-inserter with 1 video input and 1 rear-view camera input Product features Video-inserter for factory-infotainment

More information

DOGM GRAPHIC SERIES 132x32 DOTS

DOGM GRAPHIC SERIES 132x32 DOTS DOGM GRAPHIC SERIES 132x32 DOTS 6.2009 flexible display content! EA DOGM132B-5 + EA LED55x31-W TECHNICAL DATA EA DOGM132W-5 + EA LED55x31-A EA DOGM132W-6 + EA LED55x31-W * HIGH-CONTRAST LCD SUPERTWIST

More information

DEM A SBH-PW-N

DEM A SBH-PW-N DISPLAY Elektronik GmbH CONTENTS LCD MODULE DEM 160160A SBH-PW-N Version : 4.1 29.01.2008 GENERAL SPECIFICATION MODULE NO. : DEM 160160A SBH-PW-N CUSTOMER P/N VERSION NO. CHANGE DESCRIPTION DATE 0 ORIGINAL

More information

Electrical and Electronic Laboratory Faculty of Engineering Chulalongkorn University. Cathode-Ray Oscilloscope (CRO)

Electrical and Electronic Laboratory Faculty of Engineering Chulalongkorn University. Cathode-Ray Oscilloscope (CRO) 2141274 Electrical and Electronic Laboratory Faculty of Engineering Chulalongkorn University Cathode-Ray Oscilloscope (CRO) Objectives You will be able to use an oscilloscope to measure voltage, frequency

More information

7 SEGMENT LED DISPLAY KIT

7 SEGMENT LED DISPLAY KIT ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SCORE BOARD WITH THIS 7 SEGMENT LED DISPLAY KIT Version 2.0 Which pages of

More information

Bill of Materials: Magic Color PART NO

Bill of Materials: Magic Color PART NO Magic Color PART NO. 2193838 Magic color is a guessing game. With this game you can surprise your friends and leave them with amazement, how the game guesses what they have in their minds. Only two selections

More information

ADAT DC Coupling Modifications for Laser Graphic Recording

ADAT DC Coupling Modifications for Laser Graphic Recording Technical Committee ADAT DC Coupling Modifications for Laser Graphic Recording Introduction... 1 ADAT PCB Modifications... 2 Additional ADAT Information... 3 Footnotes... 6 Revision 002, October 1995 ADAT

More information

Model P2016. Dual Channel Handheld Digital Storage. Oscilloscope & Multimeter. Quick Scope Guide

Model P2016. Dual Channel Handheld Digital Storage. Oscilloscope & Multimeter. Quick Scope Guide Model P2016 Dual Channel Handheld Digital Storage Oscilloscope & Multimeter Quick Scope Guide General Warranty BNC warrants that the product will be free from defects in materials and workmanship for 3

More information

DEM K SBH-PW-N

DEM K SBH-PW-N Display Elektronik GmbH LCD MODULE DEM 128064K SBH-PW-N Product Specification Ver.: 0 13/Nov./2009 Version: 0 PAGE: 1 SPECIFICATION FOR LCM MODULE MODULE NO: DEM 128064K SBH-PW-N Customer Approval: SIGNATURE

More information

SN-Class Nixie Clock Kits

SN-Class Nixie Clock Kits Assembly Instructions And User Guide SN-Class Nixie Clock Kits - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 20 November 2017 New document - 2 - 1. INTRODUCTION 1.1 About the How can the

More information

Lesson Sequence: S4A (Scratch for Arduino)

Lesson Sequence: S4A (Scratch for Arduino) Lesson Sequence: S4A (Scratch for Arduino) Rationale: STE(A)M education (STEM with the added Arts element) brings together strands of curriculum with a logical integration. The inclusion of CODING in STE(A)M

More information

ENGR 40M Project 3a: Building an LED Cube

ENGR 40M Project 3a: Building an LED Cube ENGR 40M Project 3a: Building an LED Cube Lab due before your section, October 31 November 3 1 Introduction In this lab, you ll build a cube of light-emitting diodes (LEDs). The cube is wired to an Arduino,

More information

TRAINING. Manual. DVD-VCR COMBINATION Chassis : Kaiser SV-DVD440

TRAINING. Manual. DVD-VCR COMBINATION Chassis : Kaiser SV-DVD440 AUX DVD-VCR COMBINATION Chassis : Kaiser SV-DVD440 ELECTRONICS TRAINING MANUAL SV-DVD440 TRAINING DVD-VCR COMBINATION Manual CONTENTS 1. Precautions 2. Reference Information 3. Product Specification 4.

More information