E2O6CMRXP-1T9 drop fiber leg preparation
|
|
- Edgar Poole
- 5 years ago
- Views:
Transcription
1 User Guide E2O6CMRXP-1T9 drop fiber leg preparation E2O Drop is a F677TSVRXP drop cable combined with a 900 μm tight buffered, bend-insensitive, singlemode fiber. It is an indoor/outdoor cable with a CMR rating for use in riser applications. E2O Drop has an installation load limit of 250 pounds and a residual load of 75 pounds when the fiber and coaxial cable are joined. However, when the fiber is separated, the fiber leg has a load limit of 33 pounds and a residual load of 10 pounds. Installation load is defined as a short-term load that can be seen during installation, which, if exceeded, results in impairments to optical performance that would be permanent. Residual load is defined as a long-term load that remains with the cable post installation, which, if exceeded, results in impairments to optical performance that would be permanent. To provide perspective the normal tensile force, coaxial drop cable being pulled off a reel and through a section of conduit 200 feet long is 16 pounds of force or less. When used in riser applications, the cable has a maximum vertical rise limit of 1640 feet (500 meters). E2O6CMRXP-1T9 drop fiber leg preparation is performed using a jacket slitter and fiber stripper while following the simple process that is outlined here. Figure 1 commscope.com 1
2 The E2O6CMRXP-1T9 Drop fiber leg contains a 1.6 mm simplex fiber cable as shown in Figure 2. To access this cable, the over jacket that is used to couple the fiber leg to the coaxial cable must be removed. Figure 2 To remove the over jacket, a cable slit tool is used to slit open the over jacket. The tool has two opposing blades (Figure 3) to simultaneously slit the over jacket in two halves. Miller (Ripley) Tools Series Slitter for E2O Drop Part No.: Figure 3 Place the fiber leg into the cable slit tool, orienting the yellow tracer stripe so it faces towards the top of the tool with the tail end of the fiber towards the yellow handles as shown in Figure 4. Grasp the tool in one hand by placing the thumb and ring finger on the sides of the blocks and placing the index and middle finger on the back of the blocks; be certain to allow the fiber to pass between the index and middle finger without touching. Grasp the cable behind the tool in the other. With the fingers, apply a light amount of pressure on the blocks of the slitting tool; begin pulling the tool towards the end of the cable in a slow and steady motion while firmly holding the cable in the other hand. If too much pressure is applied, the cable jacket may stretch rather than slit; this will likely result in damage to the fiber. Figure 4 commscope.com 2
3 After completing the slit, carefully pull at the over jacket on the end of the cable to begin the separation (Figure 5). Figure 5 The two halves of the over jacket should pull apart like a banana peel (Figure 6). Figure 6 Carefully trim away the two halves of the over jacket from the cable with a pair of cutters such as scissors or sharp diagonal side cutters (Figure 7). Figure 7 commscope.com 3
4 The next step is to strip off the required amount of 1.6 mm simplex jacket from the fiber. Measure the length to be removed and mark it with some type of a marker. Use the large hole in a tri-hole fiberoptic stripper (Figure 8). This will expose the aramid yarns (yellow), two water-blocking cords (white), and the 900 μm fiber (blue). Figure 8 Miller (Ripley) Tools Tri-Hole Fiber-Optic Stripper FO-103-T-250-J Part No.: Figure 9 If necessary, trim the aramid yarns and water-blocking cords. Use the 900 μm stripping hole on the tri-hole fiber-optic stripper to strip off the 900 μm tight buffering to expose the needed length of the 250 μm fiber (Figure 10). Figure 10 The 250 μm fiber can now be stripped and prepared for slicing or connectorization. Figure 11 commscope.com 4
5 Everyone communicates. It s the essence of the human experience. How we communicate is evolving. Technology is reshaping the way we live, learn and thrive. The epicenter of this transformation is the network our passion. Our experts are rethinking the purpose, role and usage of networks to help our customers increase bandwidth, expand capacity, enhance efficiency, speed deployment and simplify migration. From remote cell sites to massive sports arenas, from busy airports to state-of-the-art data centers we provide the essential expertise and vital infrastructure your business needs to succeed. The world s most advanced networks rely on CommScope connectivity. commscope.com Visit our website or contact your local CommScope representative for more information CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks or trademarks, respectively, of CommScope, Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. CommScope is committed to the highest standards of business integrity and environmental sustainability, with a number of CommScope s facilities across the globe certified in accordance with international standards, including ISO 9001, TL 9000, and ISO Further information regarding CommScope s commitment can be found at II EN (02/17)
Mini-breakout & Mini-bundle cable. Riser cabling solution
Mini-breakout & Mini-bundle cable Riser cabling solution Mini-breakout & Mini-bundle cable Riser cabling solution CommScope s riser cables are developed for fast installations in MDUs. Their compact design
More informationPreferred ordering guide for NETCONNECT
Preferred ordering guide for NETCONNECT MEA Region Contents Copper solutions Category 6A products 3 Category 6A and Category 7 shielded copper cables 3 Category 6A modular shielded panels 3 Category 6A
More informationFOSC 400. Fiber Optic Splice Closures
FOSC 400 Fiber Optic Splice Closures FOSC 400 - Fiber Optic Splice Closures The FOSC name is synonymous with excellence in sealing, fiber management, ease of use and design flexibility. The original FOSC
More informationTECHNICAL GUIDELINE. Universal/Toneable FTTP Cable Applications Guideline. Materials Required
Universal/Toneable FTTP Cable Applications Guideline This procedure details the steps to be taken to prepare the ends of a Superior Essex Universal or Toneable FTTP Optical Fiber Cable for splicing. This
More informationInstalling a Wire Mesh Pulling Grip on All-Dielectric DX Armored Fiber Optic Cables
revision history Issue Date Reason for Change Related literature SRP-004-136 Accessing All-Dielectric DX Armored Fiber Optic Cables Admonishments 1. General This procedure provides instructions for installing
More informationSUMITOMO RECOMMENDED PROCEDURE SRP SP-F Ribbon Indoor/Outdoor Riser Cable Preparation
SUMITOMO RECOMMENDED PROCEDURE SRP SP-F02-025 Ribbon Indoor/Outdoor Riser Cable Preparation PARA. 1.0 2.0 3.0 4.0 5.0 CONTENTS General Safety Precautions Reference Documents Tools Required Sheath Removal
More informationSECTION FIBER OPTIC STATION CABLES
PART 1 GENERAL 1.01 DESCRIPTION A. The work covered by this section of the Specifications shall include all labor necessary to perform and complete such construction, all materials and equipment incorporated
More informationCrimp & Cleave Termination Instructions for SEL ST Connectors
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for SEL ST Connectors For Use With: ST Termination Kit (SEL, Part Number BT05402-01) 200 µm HCS Fiber-Optic Cable ST Crimp &
More informationLoose Tube Cable Mid-Span Access for Splicing For Series 11D, 1GD, 12D, 1AD, 1DD, 1CD, 11, 1G, 12, 12L, 1A, 1D, 1C, 1NY, 13, 1H, HZD and HZA
Loose Tube Cable Mid-Span Access for Splicing For Series 11D, 1GD, 12D, 1AD, 1DD, 1CD, 11, 1G, 12, 12L, 1A, 1D, 1C, 1NY, 13, 1H, HZD and HZA NOTE: These installation instructions have been written for
More informationFREEDM Loose Tube Interlocking Armored Cables
features and benefits Flexible, interlocking armor design Gel-free waterblocking technology Color-coded tubes and fibers UV-resistant, flameretardant jacket UV-Resistant Flame-Retardant Outer Jacket InterlockingArmor
More informationTE CONNECTIVITY <cable type> <fiber type> MM/YY SO<shop order number> XXXXX FEET
June 30th, 2015 Rev E2 Optic Interconnect Cables Simplex 1 900um Buffered Aramid Yarn Strength Members 2 s 900um Buffered Aramid Yarn Strength Members 900um Buffered 900um Buffered Aramid Yarn Strength
More informationFiber drop cable solutions. Flexible solutions for the evolving networks of tomorrow
iber drop cable solutions lexible solutions for the evolving networks of tomorrow Welcome to the Broadband Age, where your network must continually evolve to keep pace with your customers At CommScope,
More informationMiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures. 1. General. 2. Precautions
MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures 004-273-AEN, Issue 2 Table of Contents 1. General.... 1 2. Precautions.... 1 2.1 Cable Handling Precautions...
More informationInstallation Overview
Installation Overview Overview This chapter presents cable preparation and installation procedures for coaxial cables. Many connectors and special-purpose installation tools required for these cables are
More informationWater blocking tape. Locator ridge HPA-0486
Table of Contents STANDARD RECOMMENDED PROCEDURE 004-138 ISSUE 1 MARCH 2012 PAGE 1 OF 12 Sheath Removal and Mid-Span Access of Dielectric ALTOS Cable with FastAccess Technology p/n 004-138, Issue 1 1.
More informationMid-Span Access of Loose-Tube Ribbon Fiber Optic Cable
Application Notes Mid-Span Access of Loose-Tube Ribbon Fiber Optic Cable Author Prasanna Pardeshi and Sudipta Bhaumik Issued November 2013 Abstract In fiber optic network, it is sometime necessary to splice
More informationALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, Fibers
ALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, 12-72 Fibers P/N 004-223-AEN Issue 1 1. General This procedure describes cable-end and mid-span sheath removal and fiber access of ALTOS
More informationADDENDUM #3. SPECIAL NOTE: Addendum #3 information shall supersede the information contained in the Contract Documents
WESLEYAN U N I V E R S I T Y Facilities 170 Long Lane Middletown, Connecticut 06457 (860) 685-3476 FAX (860) 685-3101 ADDENDUM #3 Date: March 4, 2013 Project: To: CFA A Rehearsal Hall AHU Replacement Annual
More informationFusionLink Central Tube Ribbon Preparation & handling procedure
FusionLink Central Tube Ribbon Preparation & handling procedure Table of Contents Page # 1.0 Scope... 1 2.0 Safety...1 3.0 General Installation Considerations.... 1 4.0 Reference Drawing... 2 5.0 Tool
More informationOptiSPEED LC Keyed Red to Unconnectorized, Fiber Pigtail, 0.9 mm Tight Buffer, 12-fiber Kit, Blue - Aqua (1-12)
FAML1UC0C OptiSPEED LC Keyed Red to Unconnectorized, Fiber Pigtail, 0.9 mm Tight Buffer, 12-fiber Kit, Blue - Aqua (1-12) Fiber Type Total Fibers, quantity 12 Cord Length, maximum 23 ft 7 m Cord Length,
More informationIndustry solutions: Broadcast
Industry solutions: Broadcast Bc 2 Industry solutions: Broadcast Optical Cable Corporation s broad range of Fiber Optic Broadcast Cables are specifically designed for real-time transmission of high definition
More informationData Sheet HFBR-4531Z/4532Z/4533Z/4535Z. Crimpless Connectors for Plastic Optical Fiber and Versatile Link. Features. Description.
HFBR-4531Z/4532Z/4533Z/4535Z Crimpless Connectors for Plastic Optical Fiber and Versatile Link Data Sheet Description The HFBR-453xZ series connectors are an enhanced version of the HFBR-4501Z and HFBR-4503Z
More information@ Termination and Test Tools. Tools & Test Equipment Product Datasheet.
Tri Hole STRIPPER Fibre Optic Stripper OPT-FOS This hard wearing, easy to handle fibre optic stripping tool includes three stripping guides for: 2mm outer jacket, 900µm Buffer, and 250µm acrylic coating,
More informationSYSTIMAX Solutions InstaPATCH 360 Pre-Terminated Fiber Solution Guide
www.commscope.com SYSTIMAX Solutions InstaPATCH 360 Pre-Terminated Fiber Solution Guide Introduction The information in this solution guide will be instrumental in helping you determine the right products
More informationFiber ICT. Optical Fiber Catalogue
Catalogue Index Registers RFP 24-24 Fibers indoor wallmount box..... 02 RFP 48-48 Fibers indoor wallmount box..... 02 RFS 8-8 Fibers wallmount box..... 02 PATCH-24F - Patch Panel F.O. 9 with 24 SC/APC....
More informationFIBER OPTIC CABLE PULLING
C H A P T E R 15 FIBER OPTIC CABLE PULLING THOMAS A. DOOLEY AND JERALD R. ROUNDS (with hints from Northern Lights Cable) Electrical wire installers know how to pull cable. The basic approach to pulling
More informationFurcation of a Central Tube Ribbon, Gel-Free, Non-Armored, 96- to 192-Fiber Cable into an OSE-UD
Furcation of a Central Tube Ribbon, Gel-Free, Non-Armored, 96- to 192-Fiber Cable into an OSE-UD P/N 004-277-AEN Issue 1 related literature Search www.corning.com/opcomm. Click on Resources. 1. Initial
More informationNGF optical distribution frame
NGF optical distribution frame Contents Introduction 3 Product overview 3 Things to consider when ordering 4 Frame capacity requirements (important facts on trough space) 4 Frame lineup capacity comparisons
More informationSmall footprint, big advantages: how connectors enable the networks of tomorrow
White Paper Small footprint, big advantages: how 4.3-10 connectors enable the networks of tomorrow Pedro Torres, Mobility Network Engineering July 2016 Miniature Outside Plant Plug-and-Play Solutions Contents
More informationSection Communications Optical Fiber Backbone Cabling
Part 1 1.1 Related Documents 1.1.1 Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specifications Sections apply to this Section. 1.2 Related
More informationRF connectivity solutions guide
RF connectivity solutions guide CommScope RF connectivity solutions The pressure on MSOs has never been greater because subscriber expectations have never been higher. Whether streaming digital video or
More informationPreferred ordering guide for NETCONNECT
Preferred ordering guide for NETCONNECT European Region Table of contents Copper solutions...3 Category 7/7A...3 Category 7A S/FTP cables...3 Category 7 S/FTP cables...3 Category 7 F/FTP cables...3 Category
More informationOPTICAL CABLE FIBER-LAN INDOOR
OPTICAL CABLE FIBER-LAN INDOOR Product Type Optic Cable Construction RoHS-2 Compliant Dielectric Tight Buffer Singlemode or Multimode Description Optical cable with singlemode or multimode optical fibers
More information2178 Fiber Optic Splice Case and 2181 Cable Addition Kit
2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice
More informationNC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM
NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM Content 1. General 5 2. The products of NC-1000 system 6 3. Mounting of the frame 8 4. Earthing of the frame 8 NC-1000 FIBRE OPTIC
More informationFiber Optic Product Overview
Fiber Optic Product Overview Fiber Optic Product Overview Competence and Experience Schleuniger AG was founded in Switzerland in 1985. Our first product was a semi-automatic coaxial cable stripping machine
More informationGF-KSW-48 Series of Fiber Optic Distribution Box. Instruction Manual
Instruction manual GF/KSW/48 Page Nr 1 GF-KSW-48 Series of Fiber Optic Distribution Box Instruction Manual 1. General Introduction GF-KSW-48 series of fiber optic distribution box is applicable to fiber
More informationFIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.
FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories
More informationProduct Catalogue. Fibre Optic Cable
Product Catalogue Fibre Optic Cable version 2017 Empowering businesses through innovative network solutions. We have been pushing boundaries and providing innovative products and solutions to clients around
More informationEmpowering businesses through innovative network solutions.
Empowering businesses through innovative network solutions. We have been pushing boundaries and providing innovative products and solutions to clients around the world for nearly two decades. Our experience
More information2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table
FIST-GCO2-F INSTALLATION INSTRUCTION GCO2-FC GCO2-FD Content 1 Introduction 2 General 2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table 3 Installation
More informationProduct Catalogue. Fiber Optic Assemblies & Adapters. Table of Contents General Description... 2
Product Catalogue Fiber Optic Assemblies & Adapters Table of Contents 1. General Description... 2 2. Connectors... 3 2.1 SC/UPC... 3 2.2 SC/APC... 3 2.3 FC/UPC... 3 2.4 FC/APC... 3 2.5 ST/UPC... 3 2.6
More informationTENDER SUMMARY. Tender Title:
TENDER SUMMARY Tender Title: Tender Ref: Closing Date: OPEN TENDER FOR THE SUPPLY OF FIBER OPTIC CABLE 384 CORE LOOSE TUBE ( FOC 384C ) FOR TELEKOM MALAYSIA BERHAD ( TM ) LPM/2018/T/02/FOC 384C 23 February
More information3M Fiber Optic Wall Mount Enclosure 8430 Series
3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6
More informationSOLO ADSS Short-Span Cables, Fibers
features and benefits Loose tube design Self-supporting Track-resistant jacket available Innovative waterblocking cable core SOLO ADSS Cable Drawing ZA-2615 Stable performance and compatibility with all
More informationFollow The Leader In Shielded Technology
1970s Vampire Tap 1990s Shielded Modular Jack 190s 4 Position Data Connector Follow The Leader In Shielded Technology The new AMP-TWIST Jack is our latest shielded product evolution. It can be terminated
More informationHES HACILAR ELEKTRİK SANAYİ VE TİC.A.Ş.
Technical Specification Revision/Date: 04/04.15 By N.KARAAĞAÇ Date : 27 February 2015 Cable Type HES Cable Product Number :, Outdoor F/O Cable :FOZZXXXSJSA41JYY (ZZ: fiber type G652=SD, G657 A1 = A1, G657
More informationGigaSPEED X10D F/UTP. SYSTIMAX solutions
GigaSPEED X10D F/UTP SYSTIMAX solutions Contents Introduction 3 SYSTIMAX GigaSPEED X10D F/UTP channel performance 3 SYSTIMAX GigaSPEED X10D 91 series F/UTP cable 5 SYSTIMAX GigaSPEED X10D G10FP F/UTP 6
More informationOPTICAL FIBRE CABLE NETWORK 2004/1
OPTICAL FIBRE CABLE NETWORK 2004/1 HELKAMA OPTICAL FIBRE CABLES Cabled optical fibre characteristics OS1 singlemode fibre SM ITU-T G.652 Mode field diameter 1310nm 9.3+/-0.5µm Mode field eccentricity 1.0
More informationWhite paper. The impact of cellular deployment on MSO networks at lower frequency bands
White paper The impact of cellular deployment on MSO networks at lower frequency bands Contents Abstract 3 The rise of the cellular networks 3 The evolution of cable TV networks 3 The inevitability of
More informationSumitomo Cable Specification SE-*RU. OFNP Rated Central Tube Cable with Optical Fibers. Issued: December 2014
Sumitomo Cable Specification SE-*RU Litepipe Ribbon Indoor Plenum Cable OFNP Rated Central Tube Cable with 12-432 Optical Fibers Issued: December 2014 78 Alexander Drive, Research Triangle Park, NC 27709
More informationKeyed LC Connector Solution A LANscape Solutions Product
Applications Department of Defense installations Secure government facilities Research labs Organizations with a desire to segregate networks due to privacy or security concerns Keyed LC Connector Solution
More informationDIY. How to install a PL-259 connector. Parts list: Tools list: Worthwhile projects you can build on your own
DIY Worthwhile projects you can build on your own Just like you, I often need to install a PL-259 connector on a length of coax (coaxial cable), to attach it to the mating SO-239 connector of a mobile
More informationOptical Fiber Link, 0.1~ 20 GHz RF Over Fiber, I-IFLRF12
Fiber Link, 0.1~ 20 GHz RF Over Fiber, I-IFLRF12 Our I-IFLRF20 series is a wideband RF over fiber link that provides optical transport of RF signals in radars, satcom, EW/ECM and other antenna remoting
More informationOCC Installation Conduit Guidelines Excerpt from Optical Cable Corporation s INSTALLATION GUIDE
Installation Conduit Guidelines Excerpt from Optical Cable Corporation s INSTALLATION GUIDE Conduit Installation A conduit cable installation involves placement of one or more optical cables inside a preinstalled
More informationTECHNICAL SPECIFICATION
ISSUED : OCT. 02, 2006 PAGE : 1 OF 9 REV. : 1 TECHNICAL SPECIFICATION FOR GST 2006-043A LOOSE TUBE DRY CORE CABLE SINGLE JACKET/SINGLE ARMOR (SJSA CABLE) Prepared By : Oh-Heoung Kwon Engineer Optical Technical
More informationLANmark-OF ENSPACE Patch Panel
LANmark-OF ENSPACE Patch Panel PRODUCT INSTALLATION GUIDE September 2016 v0.11 LANmark-OF ENSPACE Patch Panel PRODUCT INSTALLATION GUIDE Part Number Description Product References NSPACE.PP1U NSPACE.PP2U
More informationMPS Webinar Technical Series
MPS Webinar Technical Series Making Connections: Navigating Fiber Optic Cabling and Interconnection Requirements microwave photonic systems Expand Your RF Horizons Introduction Microwave Photonic Systems
More informationMulti-Media Installation Guide
Multi-Media Installation Guide Coaxial Page 2 Data Plug Page 7 Data Jack Page 10 Telephone Page 13 Splicing Page 15 Cable Types Cable Types Two basic types of cable are used in multimedia installations.
More informationMT-RJ SECURE Product Expansion Now 10 Variants of the MT-RJ SECURE Products
MT-RJ Product Expansion Now 0 Variants of the MT-RJ Products In response to several customers, the MT-RJ product line has been expanded with an additional six color/key versions. In addition to the original
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BEFORE INSTALLING OR ADJUSTING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY. PLEASE KEEP THIS GUIDE FOR FUTURE REFERENCE FIBER OPTIC SWING-OUT PATCH PANEL INSTRUCTION
More informationPRO SERIES FIBRE-150M
Product Information Document PRO SERIES Ruggedised multimode optical fibre cable with Neutrik* opticalcon DUO connectors Length 150 metres Supplied on Schill* GT310 drum with rubberised frame and integral
More informationGel-sealed in-line fiber optic closure
SCIL-C Gel donut INSTALLATION INSTRUCTION TC-1363-1-IP Rev A, Oct 2017 www.commscope.com Gel-sealed in-line fiber optic closure Contents 1 General 2 Sizing and product kit information 3 Installation conditions
More informationUNIVERSITY of NORTH DAKOTA LOW VOLTAGE COMMUNICATIONS STANDARDS FOR CABLING, PATHWAYS, AND SPACE
UNIVERSITY of NORTH DAKOTA LOW VOLTAGE COMMUNICATIONS STANDARDS FOR CABLING, PATHWAYS, AND SPACE Prepared in cooperation and approval from BICSI Building Industry Consulting Services International and
More informationSpecification for Loose Tube Fiber Optic Cable (Non-Metallic, Dry Block, Figure-8) (G.652.D)
2-3, Marunouchi 2-chome, Chiyoda-ku, Tokyo 100-8322, Japan No. FB-KL4001C for Loose Tube Fiber Optic Cable (Non-Metallic, Dry Block, Figure-8) (G.652.D) Aug 2014 1 1. General This specification describes
More informationSUMITOMO PRODUCT SPECIFICATION. FutureFLEX. TCxxMSOS DIELECTRIC HIGH PERFORMANCE OSP TUBE CABLE SERIES
SUMITOMO PRODUCT SPECIFICATION FutureFLEX TCxxMSOS DIELECTRIC HIGH PERFORMANCE OSP TUBE CABLE SERIES SUMITOMO ELECTRIC LIGHTWAVE CORP. 201 South Rogers Lane, Suite 100, Raleigh, NC 27610 (919) 541-8100
More informationSJOF-BS604B. Fiber Optic Splice Closure User Manual Rev.1
Fiber Optic Splice Closure 1. Introduction 1.1 General SAMJIN s SJOF-BS604B protects fiber optic splicing point in various installation conditions such as aerial, manholes, ducts, wall and direct buried
More informationHD4K18GB-FO-xx-MM. HDMI 2.0 Active Optic Cables. Instruction Manual
HD4K18GB-FO-xx-MM HDMI 2.0 Active Optic Cables Instruction Manual 1 HDMI 2.0 Active Optic Cable INTRODUCTION This Fiber Optic HDMI 2.0 Active Optic Cable (AOC) allows you to transmit HDMI signals to a
More informationPublic Works Division Lighting District Fiber Optic Specifications April 2009
Public Works Division Lighting District Fiber Optic Specifications April 2009 7000 Florida Street Punta Gorda, Florida 33950 Tele: 941.575.3600 Fax : 941.637.9265 www.charlottecountyfl.com/publicworks
More information24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual
24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number
More informationMicrowave Backhaul Solutions SUPER HIGH PERFORMANCE ANTENNAS. Not just a new backhaul solution a whole new backhaul strategy
Microwave Backhaul Solutions SUPER HIGH PERFORMANCE ANTENNAS Not just a new backhaul solution a whole new backhaul strategy Sentinel Class 4 antennas from our Andrew Portfolio When you think about network
More informationMining and Petrochemical Fiber Optic Cables
Features and Benefits Loose construction Stable and highly reliable transmission parameters Waterblocking technology Allows efficient and craft-friendly cable preparation in outdoor or indoor/outdoor applications
More informationSPECIFICATION 96F SM LOOSE TUBE, DRY CORE MINI CABLE
Revision No.:01 Date: 07.10.06 SPECIFICATION OF 96F SM LOOSE TUBE, DRY CORE MINI CABLE PART NO.:D-96/SM/MTY(F)-MFN-O6.3 Checked By: Pavan Maheshwari Process Associate Design & Development Team Approved
More informationConnected Solutions. April $ Post, 19 Rack ELERK1FR BK
Connected Solutions April 2018 $30.97 Punch & Go Tool ONQAC3400 $139.97 per 305M Category 6 Riser, UTP, 23 AWG, Blue 305 Meter/1000 FT Pull Box CAB24/4PS6FT4BLUHYP $137.97 2 Post, 19 Rack ELERK1FR1194400BK
More informationTable 4-1: Rating Levels
OBJECTIVES 1. Describe various level ratings that apply to telecommunication cables and jacks and identify where each is implemented. 2. Describe the various levels of the cabling category rating systems.
More informationOFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation
OFDC-B8-72 I N S T A L L A T I O N I N S T R U C T I O N Outdoor fiber distribution closure Content 1 Introduction 2 Kit content 3 Closure preparation 4 Cable preparation 4.1 Feeder cable 4.2 Drop cable
More informationFACT Cable Termination Unit
FACT Cable Termination Unit INSTALLATION INSTRUCTION FACT-GSS NOTE: - the FACT-GSS multi-purpose splice shelves features Single Circuit and Single Element fiber management system technology - these shelves
More informationAbout Nexans 3. About Berk-Tek 4. Hyper Plus 5e Cat 5e UTP 5. HyperPlus 5e Plenum 6. Hyper Plus 5e Riser 10. HyperPlus 5e Patch 14
Table of contents About Nexans 3 About Berk-Tek 4 Hyper Plus 5e Cat 5e UTP 5 HyperPlus 5e Plenum 6 Hyper Plus 5e Riser 10 HyperPlus 5e Patch 14 HyperPlus 5e OSP 18 22 7/10/07 - http://www.berktek.com Page
More informationDIAS power supply and DIC 221 fibre optic cable coupling module
POWER SUPPLY AND FIBRE OPTIC COUPLING MODULE DIC 221 DIAS power supply and DIC 221 fibre optic cable coupling module for the power supply of DIAS function modules, 2 x fibre optic cable connections (DIAS
More information3M Better Buried Closures
3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...
More informationService Call: Fiber Optic Installation and Repair
Service Call: Fiber Optic Installation and Repair Tools Required: Tools available from www.bohlinger.biz Cable: Terex P/N 453830 Stripper Block: P/N 65-020-01 Termination Block: P/N 65-020-02 Utility Knife
More informationSPECIFICATION. Spec No : VSS-1402-CS603B
SPECIFICATION Spec No : VSS-1402-CS603B 1. INTRODUCTION 1.1. General This specification covers the design requirements and characteristics required of fiber optic splice closures to be used on fiber optic
More informationCONNECTING THE FUTURE 19" LINXS LIGHTWAVE INTEGRATED CROSS-CONNECT SYSTEM USER MANUAL
CONNECTING THE FUTURE 19" LINXS LIGHTWVE INTEGRTED CROSS-CONNECT SYSTEM USER MNUL 109003 Issue Rev 2 19" Lightwave Integrated Cross-Connect System (LINXS) User Manual Document Number 109003 Issue Rev 2
More informationDigamber Telecom.
+91-8048409600 Digamber Telecom https://www.sancharcable.com/ We are a reputed manufacturer and supplier of Telecom Industrial Products & Cables that is working hard from over many years to achieve utmost
More informationSumitomo Cable Specification SE-*DB. 100% Dry - Armored Central Tube Ribbon Cable with Fibers. Issued: January 2014
Sumitomo Cable Specification SE-*DB DriTube Ribbon / Armorlux Sheath Cable 100% Dry - Armored Central Tube Ribbon Cable with 12-576 Fibers Issued: January 2014 78 Alexander Drive, Research Triangle Park,
More informationMedium Box for Cable Termination
FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling
More informationSPECIAL SPECIFICATION :1 Video (De) Mux with Data Channel
1993 Specifications CSJ 0924-06-223 SPECIAL SPECIFICATION 1160 8:1 Video (De) Mux with Data Channel 1. Description. This Item shall govern for furnishing and installing an 8 channel digital multiplexed
More informationRFP LC Uniboot to RFP LC Uniboot Patch cord, 2 fibres, Interconnect tight-buffered cable, LSZH
1 1 9.41 115 0 Pretium EDGE 143 RFP LC Uniboot to RFP LC Uniboot Patch Pretium EDGE Solutions jumpers are integrated reverse -polarity uniboot duplex assemblies that meet the high -density space requirements
More informationNon-metallic Aerial Distribution Optical Cables for FTTH Networks
Non-metallic Aerial Distribution Optical Cables for FTTH Networks Go Taki, 1 Akira Namazue, 1 and Ken Osato 1 One of the common practices to construct economical and efficient Fiber To The Home (FTTH)
More informationFOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
More informationAbout Nexans 3. About Berk-Tek 4. LANmark-1000 Cat 6 UTP 5. LANmark-1000 Category 6 Plenum 6. LANmark-1000 Category 6 Riser 11
Table of contents About Nexans 3 About Berk-Tek 4 LANmark-1000 Cat 6 UTP 5 LANmark-1000 Category 6 Plenum 6 LANmark-1000 Category 6 Riser 11 LANmark-1000 Category 6 Patch 16 21 7/10/07 - http://www.berktek.com
More informationAFL Telecommunications
' portfolio of fiber optic cable products is more impressive than any other telecommunications company in the world. But with AFL, you're getting more than just quality products. You're hiring a team of
More informationTriax TechInfo. Installing and pulling Fibre Optic cables
Installation methods for both wire cables and Fibre Optical cables are similar. Fibre cable can be pulled with much greater force than copper wire if you pull it correctly. Just remember these rules: 1)
More information2002, Cisco Systems, Inc. All rights reserved.
2002, Cisco Systems, Inc. All rights reserved. 1 Panduit Network Infrastructure Essentials Chapter 8 Tools of the Trade Learning Objectives Learn about common tools used in the telecommunications cabling
More information- Outdoor & Indoor Telephone Cables - Fiber Optic Cables - Electronic Control Cables - Control Cables - Data/LAN Cables - Coaxial Cables
ETK CABLE CO. which has been playing an active role in Global Cable Market since 1979, carries on its cable manufacturing activity in a production plant of 50.000 square meters in Sancaktepe-Istanbul.
More informationCrimplok. Connectors. 3M Crimplok ST* Connector Multimode 1. 3M Crimplok SC Connector Single-mode 2
3 Crimplok Connectors Quick, easy installation and superior performance To successfully design, install or operate today s fiber optic networks, you need components that offer speed and reliability from
More informationMOST - Roadmap Physical Layer & Connectivity from 150Mbps to 5Gbps
MOST - Roadmap Physical Layer & Connectivity from 150Mbps to 5Gbps 13th MOST(R) Interconnectivity Conference Asia on November 15, 2012 in Seoul, South Korea Andreas Engel Manager Advanced Infotainment
More informationTELECOM SOLUTIONS SOLUTIONS CATALOGUE INNOVATIVE FIBRE OPTIC CABLE SOLUTIONS
TELECOM SOLUTIONS SOLUTIONS CATALOGUE INNOVATIVE FIBRE OPTIC CABLE SOLUTIONS TKF TECHNOLOGICAL LEADERSHIP IN CONNECTIVITY SOLUTIONS Since its establishment in 1930 TKF developed from a cable producer to
More informationTable of Contents. Specifying AFL Premise Optical Cables Outdoor. Enterprise. Interconnect. MicroCore. Indoor.
Table of Contents Specifying AFL Premise Optical Cables... 2 Enterprise Fiber-In-A-Box... 3 Interconnect Simplex Cable....................................... 4 Zipcord and DUAL-Link Cable... 6 Furcation
More information3M Knifeless Tape. Finish Line Perf Line Bridge Line Design Line Tri Line Precision Line PPF Line. Product Description. Commercial Solutions Division
Effective January 2017 Commercial Solutions Division 3M Knifeless Tape Finish Line Perf Line Bridge Line Design Line Tri Line Precision Line PPF Line Product Description 3M Knifeless Tapes are filament
More information