E3NX-FA. Smart Fiber Amplifier Units. A Smart Fiber Amplifier Unit with Ultra-stable Detection and Ultra-easy Setup. Ordering Information

Transcription

1 Smart Fiber Amplifier Units ENX-FA CSM_ENX-FA_DS_E_6_ A Smart Fiber Amplifier Unit with Ultra-stable Detection and Ultra-easy Setup Improved basic performance with.5 times the sensing distance and approx. /0th the minimum sensing object.* Ultra-easy setup with Smart Tuning with a light intensity adjustment range expanded 20 times to 40,000:. Optimum stable detection achieved with light intensity adjustment even for saturated incident light. White on black display characters for high visibility. Solution Viewer that shows the passing time and difference in incident levels and Change Finder that allows you to see display values even for fast workpieces. * Compared to the EX-HD. Refer to the Safety Precautions on page 7. For the most recent information on ls that have been certified for safety standards, refer to your OMR website. Ordering Information Fiber Amplifier Units (Dimensions pages 9 and 20) Type Connecting Appearance Inputs/outputs NPN output PNP output ENX-FA 2M ENX-FA4 2M Pre-wired (2 m) output Standard ls ENX-FA-5 2M * --- Wire-saving Connector output ENX-FA6 ENX-FA8 Pre-wired (2 m) 2 outputs + input ENX-FA2 2M ENX-FA5 2M Advanced ls Wire-saving Connector output + input ENX-FA7 ENX-FA9 2 outputs ENX-FA7TW ENX-FA9TW M8 Connector output + input ENX-FA24 ENX-FA54 2 outputs --- ENX-FA54TW *. This type can prevent mutual interference for two units in the SHS2.

2 Type Connecting Appearance Inputs/outputs NPN output PNP output Pre-wired (2 m) output ENX-FAH 2M ENX-FAH4 2M Infrared ls Wire-saving Connector output ENX-FAH6 ENX-FAH8 Analog output ls Pre-wired (2 m) 2 outputs ENX-FAAN 2M ENX-FA4AN 2M for Sensor Communications Unit *2 Connector for Sensor Communications Unit --- ENX-FA0 ENX-FAH0 Connector for Sensor Communications Unit Pre-wired (2 m) output ENX-FA0 2M ENX-FA40 2M *2. A Sensor Communications Unit is required if you want to use the Fiber Amplifier Unit on a network. Accessories (Sold Separately) Wire-saving Connectors (Required for ls for Wire-saving Connectors.) (Dimensions page 2) Connectors are not provided with the Fiber Amplifier Unit and must be ordered separately. Note: Protective stickers are provided. Type Appearance Cable length No. of conductors Applicable Fiber Amplifier Units Master Connector 4 EX-CN2 ENX-FA7 ENX-FA7TW ENX-FA9 Slave Connector 2 EX-CN22 ENX-FA9TW 2 m Master Connector EX-CN Slave Connector EX-CN2 ENX-FA6 ENX-FA8 Sensor I/O Connectors (Required for ls for M8 Connectors.) (Dimensions page 2) Connectors are not provided with the Fiber Amplifier Unit and must be ordered separately. Size Cable Appearance Cable type M8 Standard cable Straight L-shaped 2m 5m 2m 5m 4-wire XSF-M A XSF-M A XSF-M A XSF-M A 2

3 Mounting Bracket (Dimensions page 22) A Mounting Bracket is not provided with the Fiber Amplifier Unit. It must be ordered separately as required. Appearance Quantity Related Products Sensor Communications Units Type Appearance E9-L4 Sensor Communications Unit for EtherCAT ENW-ECT DIN Track (Dimensions page 22) A DIN Track is not provided with the Fiber Amplifier Unit. It must be ordered separately as required. Appearance Type Quantity Shallow type, total length: m Shallow type, total length: 0.5 m PFP-00N PFP-50N Sensor Communications Unit for CompoNet Sensor Communications Unit for CC-Link ENW-CRT * ENW-CCL Deep type, total length: m PFP-00N2 End Plate (Dimensions page 22) Two End Plates are provided with the Sensor Communications Unit. End Plates are not provided with the Fiber Amplifier Unit. They must be ordered separately as required. Appearance Quantity PFP-M Cover Attach these Covers to Amplifier Units. Order a Cover when required, e.g., if you lose the covers. Appearance Quantity E9-G25 FOR ENX-FA Distributed Sensor Unit *2 ENW-DS Refer to your OMR website for details. *. ENX-FAH0 can not be connected. *2. The Distributed Sensor Unit can be connected to any of the Sensor Communications Units. EtherCAT is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. CompoNet is a registered trademark of the ODVA. CC-Link is a registered trademark of Mitsubishi Electric Corporation. The trademark is managed by the CC-Link Partner Association.

4 Ratings and Specifications Standard ls/ Advanced ls/ Infrared ls Item Inputs/ outputs Giga-power 0 (GIGA) *. This type can prevent mutual interference for two units in the SHS2. *2. At Power supply voltage of 0 to 0 VDC Standard s: Normal : 990 mw max. (Current consumption: ma max. at 0 VDC, 65 ma max. at 0 VDC) Eco function : 780 mw max. (Current consumption: 26 ma max. at 0 VDC, 42 ma max. at 0 VDC) Eco function LO : 840 mw max. (Current consumption: 28 ma max. at 0 VDC, 45 ma max. at 0 VDC) Advanced s: Normal :,020 mw max. (Current consumption: 4 ma max. at 0 VDC, 67 ma max. at 0 VDC) Eco function : 80 mw max. (Current consumption: 27 ma max. at 0 VDC, 44 ma max. at 0 VDC) Eco function LO : 870 mw max. (Current consumption: 29 ma max. at 0 VDC, 48 ma max. at 0 VDC) Infrared ls: Normal :,260 mw max. (Current consumption: 42 ma max. at 0 VDC, 80 ma max. at 0 VDC) Eco function :,050 mw max. (Current consumption: 5 ma max. at 0 VDC, 60 ma max. at 0 VDC) Eco function LO :,40 mw max. (Current consumption: 8 ma max. at 0 VDC, 70 ma max. at 0 VDC) *. The following details apply to the input. *-.Input time is 25 ms ()/() only when (in tune) or (in PtUn) input is selected. *4. The tuning will not change the number of units. The least unit count among the mutual interference prevention units of ENX and ENC. Check the mutual interference prevention unit count and response speed of each l. ENX-FA Type Standard ls Advanced ls Infrared ls NPN output ENX-FA ENX-FA6 ENX-FA-5 * ENX-FA2 ENX-FA7 ENX-FA7TW ENX-FA ENX-FAH ENX-FAH6 PNP output ENX-FA4 ENX-FA8 --- ENX-FA5 ENX-FA9 ENX-FA9TW ENX-FA54 ENX-FA54TW ENX-FAH4 ENX-FAH8 Connecting Pre-wired Wire-saving Connector Pre-wired Pre-wired Wire-saving Connector M8 Connector Pre-wired s output 2 outputs output 2 outputs output 2 outputs outputs External inputs --- input input --- input Light source (wavelength) Red, 4-element LED (625 nm) Infrared LED (870nm) Power supply voltage Power consumption *2 Control output 0 to 0 VDC, including 0% ripple (p-p) At Power supply voltage of 24 VDC Standard s: Normal : 840 mw max. (Current consumption at 5 ma max.) Eco function : 650 mw max. (Current consumption at 27 ma max.) Eco function LO : 750 mw max. (Current consumption at ma max.) Advanced s or for Sensor Communications Unit: Normal : 920 mw max. (Current consumption at 8 ma max.) Eco function : 680 mw max. (Current consumption at 28 ma max.) Eco function LO : 800 mw max. (Current consumption at ma max.) Infrared ls: Normal : 080 mw max. (Current consumption at 45 ma max.) Eco function : 920 mw max. (Current consumption at 8 ma max.) Eco function LO : 020 mw max. (Current consumption at 42 ma max.) power supply voltage: 0 VDC max., open-collector output (depends on the NPN/PNP output format) current: Groups of to Amplifier Units: 00 ma max., Groups of 4 to 0 Amplifier Units: 20 ma max. Residual voltage: At load current of less than 0 ma: V max. At load current of 0 to 00 ma: 2 V max. current: 0. ma max. External inputs --- Refer to *. --- Refer to *. --- Indicators Protection circuits (SHS) Response time (HS) Standard (Stnd) Giga-power (GIGA) 7-segment displays (Sub digital display: green, Main digital display: white) Display direction: Switchable between normal and reversed. OUT indicator, L/D indicator, ST indicator (blue), DPC indicator (green), and OUT selection indicator (orange, only on ls with 2 outputs) Power supply reverse polarity protection, output short-circuit protection, and output reve rse polarity protection Wire-saving Connector or reset for l with output: 0 μs (Super High Speed (SHS2) of ENX-FA-5 is 60 μs each), with 2 outputs: 2 μs or reset: 250 μs or reset: ms or reset: 6 ms Sensitivity adjustment Smart Tuning (2-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, or percentage tuning (-99% to 99%)) or manual adjustment Maximum connectable Units 0 No. of Units for mutual interference prevention *4 NPN PNP (SHS) (HS) Standard (Stnd) 0 Note: 2 units when the detection is set to Super High Speed (SHS2), and for other ls, the mutual interference prevention function is disabled. 0 0 Contact input (relay or switch) Non-contact input () Input time *- : Shorted to 0 V (Sourcing current: ma max.). : Open or shorted to Vcc. : Shorted to Vcc (Sinking current: ma max.). : Open or shorted to 0 V. :.5 V max. (Sourcing current: ma max.) : Vcc.5 V to Vcc (Leakage current: 0. ma max.) : Vcc.5 V to Vcc (Sinking current: ma max.) :.5 V max. (Leakage current: 0. ma max.) : 9 ms min. : 20 ms min. 4

5 Item Functions Type Standard ls Advanced ls Infrared ls NPN output ENX-FA ENX-FA6 ENX-FA-5 * ENX-FA2 ENX-FA7 ENX-FA7TW ENX-FA ENX-FAH ENX-FAH6 PNP output ENX-FA4 ENX-FA8 --- ENX-FA5 ENX-FA9 ENX-FA9TW ENX-FA54 ENX-FA54TW ENX-FAH4 ENX-FAH8 Connectin g Automatic power control (APC) Dynamic power control (DPC) Timer Zero reset Resetting settings *5 Eco *6 Pre-wired Always enabled. Provided Wire-saving Connector *5. The bank is not reset by the user reset function or saved by the user save function. *6. Eco LO is supported for Amplifier Units manufactured in July 204 or later. *7. When the number of connected units is or more, the ambient temperature is less than 50 C. Pre-wired Pre-wired Wire-saving Connector M8 Connector Pre-wired Select from timer disabled, -delay, -delay, one-shot, or -delay + -delay timer: to 9,999 ms Negative values can be displayed. (Threshold value is shifted.) Select from initial reset (factory defaults) or user reset (saved settings). Select from (digital display lit), Eco (digital display not lit), and Eco LO (digital display dimmed). Bank switching Select from banks to 4. Wire-saving Connector Power tuning Select from, or Execution on power-up. Select from or External input Ambient illumination (Receiver side) Select from normal detection, area detection or differential detection. --- Select from normal detection, alarm output, error output or differential detection. --- Select from input, tuning, power tuning, emission, zero reset, or bank switching. Select from normal detection, alarm output, error output or differential detection Select from input, tuning, power tuning, emission, zero reset, or bank switching. Select from normal detection, alarm output, error output or differential detection. Hysteresis width Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999. Ambient temperature range *7 Ambient humidity range Altitude Installation environment Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) Weight (packed state/ Sensor only) Materials Accessories Case Cover Cable Incandescent lamp: 20,000 lx max., Sunlight: 0,000 lx max. Operating: Groups of or 2 Amplifier Units: 25 to 55 C, Groups of to 0 Amplifier Units: 25 to 50 C, Groups of to 6 Amplifier Units: 25 to 45 C, Groups of 7 to 0 Amplifier Units: 25 to 40 C Storage: 0 to 70 C (with no icing or condensation) Operating and storage: 5 to 85% (with no condensation) within the surrounding air temperature range shown above 2,000 m max. Pollution degree 20 MΩ min. (at 500 VDC),000 VAC at 50/60 Hz for min 0 to 55 Hz with a.5-mm double amplitude for 2 hours each in X, Y, and Z directions 500 m/s 2 for times each in X, Y, and Z directions Approx. 5 g/ approx. 75 g Approx. 60g/ approx. 20g Polycarbonate (PC) Polycarbonate (PC) PVC Instruction Manual Approx. 5 g/ approx. 75 g Approx. 5 g/ approx. 75 g Approx. 60g/ approx. 20g Approx. 65 g/ approx. 25 g --- Select from normal detection or area detection. --- Approx. 5 g/ approx. 75 g Approx. 60g/ approx. 20g 5

6 Analog output ls/ for Sensor Communications Unit Item Inputs/ outputs Type Analog output ls for Sensor Communications Unit NPN output ENX-FAAN ENX-FA0 PNP output ENX-FA4AN ENX-FA40 Connecting Pre-wired s 2 outputs outputs External inputs Connector for Sensor Communications Unit Pre-wired *. Two sensor outputs are allocated in the programmable logic controller PLC I/O table. PLC operation via Communications Unit enables reading detected values and changing settings. *2. At Power supply voltage of 0 to 0 VDC Analog output ls: Normal :,080 mw max. (Current consumption: 6 ma max. at 0 VDC, 75 ma max. at 0 VDC) Eco function : 840 mw max. (Current consumption: 28 ma max. at 0 VDC, 55 ma max. at 0 VDC) Eco function LO : 960 mw max. (Current consumption: 2 ma max. at 0 VDC, 65 ma max. at 0 VDC) *. The tuning will not change the number of units. The least unit count among the mutual interference prevention units of ENX and ENC. Check the mutual interference prevention unit count and response speed of each l. --- * ENX-FA0 ENX-FAH0 Connector for Sensor Communications Unit Light source (wavelength) Red, 4-element LED (625 nm) Infrared LED (870nm) Power supply voltage Power consumption *2 Control output Analog output Indicators Protection circuits Control output Response time Super-high-speed (SHS) 0 to 0 VDC, including 0% ripple (p-p) At Power supply voltage of 24 VDC Normal : 960 mw max. (Current consumption at 40 ma max.) Eco function : 770 mw max. (Current consumption at 2 ma max.) Eco function LO : 870 mw max. (Current consumption at 6 ma max.) Supplied from the connector through the communication units. At Power supply voltage of 24 VDC Normal : 920 mw max. (Current consumption at 8 ma max.) Eco function : 680 mw max. (Current consumption at 26 ma max.) Eco function LO : 800 mw max. (Current consumption at ma max.) power supply voltage: 0 VDC max., open-collector output (depends on the NPN/PNP output format) current: Groups of to Amplifier Units: 00 ma max., Groups of 4 to 0 Amplifier Units:20 ma max. Residual voltage: ( At load current of less than 0 ma: V max. ) At load current of 0 to 00 ma: 2 V max. current: 0. ma max. Voltage output: -5 VDC (0 kω or more connected load), temperature characteristics: 0.% F.S. / C 7-segment displays (Sub digital display: green, Main digital display: white) Display direction: Switchable between normal and reversed. OUT indicator, L/D indicator, ST indicator (blue), DPC indicator (green), and OUT selection indicator (orange, only on ls with 2 outputs) Power supply reverse polarity protection, output short-circuit protection, and output reverse polarity protection or reset: 80 μs or reset: 2 μs (HS) or reset: 250μs or reset: 250 μs Standard (Stnd) or reset: ms or reset: ms Giga-power (GIGA) Sensitivity adjustment or reset: 6 ms Maximum connectable Units 0 6 No. of Units for mutual interference prevention * Super-high-speed (SHS) (HS) 0 Standard (Stnd) 0 Giga-power (GIGA) or reset: 6 ms --- At Power supply voltage of 24 VDC Normal :,080 mw max. (Current consumption at 45 ma max.) Eco function : 920 mw max. (Current consumption at 8 ma max.) Eco function LO :,020 mw max. (Current consumption at 42 ma max.) Power supply reverse polarity protection and output shortcircuit protection Smart Tuning (2-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, percentage tuning ( 99% to 99%)) or manual adjustment With ENW-ECT: 0 units (When connected to an OMR NJ-series Controller.) With ENW-CRT: 6 units (Note: ENX-FAH0 can not be connected.) With ENW-CCL: 6 units 0 (The mutual interference prevention function is disabled if the detection is set to super-high-speed.)

7 Item Functions Type Analog output ls for Sensor Communications Unit NPN output ENX-FAAN ENX-FA0 PNP output ENX-FA4AN ENX-FA40 Connecting Automatic power control (APC) Dynamic power control (DPC) Timer Zero reset Resetting settings *4 Eco Pre-wired Always enabled. Provided Bank switching Select from banks to 4. Power tuning 2 Connector for Sensor Communications Unit Pre-wired *4. The bank is not reset by the user reset function or saved by the user save function. *5. When the number of connected units is or more, the ambient temperature is less than 50 C. ENX-FA0 ENX-FAH0 Connector for Sensor Communications Unit Select from timer disabled, -delay, -delay, one-shot, or -delay + -delay timer: to 9,999 ms Negative values can be displayed. (Threshold value is shifted.) Select from initial reset (factory defaults) or user reset (saved settings). Select from (digital display lit), Eco (digital display not lit), and Eco LO (digital display dimmed). Select from or. Select from Analog scaling or Analog offset. --- Select from normal detection, alarm output, error output or differential detection (ENX-FA0 only). Hysteresis width Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999. Ambient illumination (Receiver side) Ambient temperature range *5 Ambient humidity range Altitude Incandescent lamp: 20,000 lx max., Sunlight: 0,000 lx max. Operating: Groups of or 2 Amplifier Units: -25 to 55 C, Groups of to 0 Amplifier Units: -25 to 50 C, Groups of to 6 Amplifier Units: -25 to 45 C, Groups of 7 to 0 Amplifier Units: -25 to 40 C Storage: -0 to 70 C (with no icing or condensation) Operating: Groups of or 2 Amplifier Units: 0 to 55 C, Groups of to 0 Amplifier Units: 0 to 50 C, Groups of to 6 Amplifier Units: 0 to 45 C Storage: -0 to 70 C (with no icing or condensation) Operating: Groups of or 2 Amplifier Units: 0 to 55 C, Groups of to 0 Amplifier Units: 0 to 50 C, Groups of to 6 Amplifier Units: 0 to 45 C, Groups of 7 to 0 Amplifier Units: 0 to 40 C Storage: 0 to 70 C (with no icing or condensation) Operating and storage: 5 to 85% (with no condensation) within the surrounding air temperature range shown above 2,000 m max. Installation environment Pollution degree Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) 20 MΩ min. (at 500 VDC),000 VAC at 50/60 Hz for min 0 to 55 Hz with a.5-mm double amplitude for 2 hours each in X, Y, and Z directions 500 m/s 2 for times each in X, Y, and Z directions 50 m/s 2 for times each in X, Y, and Z directions Weight (packed state/sensor only) Approx. 5 g/approx. 75 g Approx. 95 g/approx. 45 g Approx. 65 g/approx. 25 g Approx. 65 g/approx. 25 g Materials Accessories Case Cover Cable Polycarbonate (PC) Polycarbonate (PC) PVC Instruction Manual 7

8 Distances Standard ls/ Advanced ls/ Analog output ls Threaded s Reflective direction Right-angle Straight Right-angle Straight *. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. Cylindrical s Reflective Size Size M4 Giga distance (mm) Standard ENX-FA E2-TN 2M,000,500, E2-LTN 2M 4,000 * 4,000 *, E2-TR 2M,000,500, E2-LT 2M 4,000 * 4,000 * 4,000 *,080 E2-LTR 2M 4,000 * 4,000 *, E2-CN 2M M E2-C2N 2M M4 E2-D2N 2M, M6 E2-CN 2M, E2-LDN 2M, E2-D2R 2M M E2-C 2M E2-CM M M4 E2-D2R 2M M6 direction E2-DR 2M, E2-CC200 2M 2, E2-LD 2M, E2-LDR 2M, Giga distance (mm) Standard dia. E2-T22R 2M dia. E2-T22B 2M, dia..5 dia..5 dia dia. dia. dia dia. E2-T2R 2M,000,500, Side-view E2-T4LR 2M, E2-D22B 2M E2-D4M M E2-D22R 2M E2-D22B 2M E2-D2L 2M, E2-D 2M Flat s Reflective direction Giga distance (mm) Standard E2-T5XR 2M,000,500, Side-view E2-T5YR 2M, Flat-view E2-T5ZR 2M E2-D5XR 2M, Side-view E2-D5YR 2M Flat-view E2-D5ZR 2M 8

9 Sleeve s Reflective direction Side-view Side-view Giga distance (mm) Standard E2-T24R 2M E2-T24E 2M E2-T M E2-T2-S 2M E2-TC200BR 2M,000,500, E2-D24R 2M E2-D24-S2 2M E2-D4M M E2-D 2M E2-D 2M E2-D2-S 0.5M E2-D-S 0.5M E2-DC200F4R 2M E2-D22-S 2M E2-D2-S 2M E2-DC200BR 2M, E2-D25-S 2M Small-spot, Reflective s Type Variable spot Spot diameter Center distance (mm) s Giga distance (mm) Standard 0. to 0.6 dia. 6 to 5 E2-C42 M + E9-FA Spot diameter of 0. to 0.6 mm at 6 to 5 mm. 0. to.6 dia. 0 to 0 E2-C42 M + E9-F7 Spot diameter of 0. to.6 mm at 0 to 0 mm. Parallel light 4 dia. 0 to 20 Integrated lens Small-spot E2-C 2M + E9-FC E2-CN 2M + E9-FC Spot diameter of 4 mm max. at 0 to 20 mm. 0. dia. 5 E2-C42S M Spot diameter of 0. mm at 5 mm. 6 dia. 50 E2-L5 2M Spot diameter of 6 mm at 50 mm. 0. dia. 0.5 dia. 0.2 dia. 0.5 dia. 7 7 dia. 50 E2-C4 M + E9-FA-5 E2-C 2M + E9-FA-5 E2-CN 2M + E9-FA-5 E2-C4 M + E9-FB E2-C 2M + E9-FB E2-CN 2M + E9-FB E2-CC200 2M + E9-F8 E2-CN 2M + E9-F8 Spot diameter of 0. mm at 7 mm. Spot diameter of 0.5 mm at 7 mm. Spot diameter of 0.2 mm at 7 mm. Spot diameter of 0.5 mm at 7 mm. Spot diameter of mm at 50 mm. 9

10 High-power Beam s Type ls with integrated lens ls with lenses Reflective ls with integrated lens direction *. The fiber length is 0 m on each side, so the sensing distance is given as 20,000 mm. *2. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. Narrow View s Aperture angle s *. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. s for Detection without Background Interference Giga distance (mm) Standard Right-angle 5 E2-LTN 2M 4,000 *2 4,000 *2, E2-T7L 0M 20,000 * 20,000 * 20,000 * 8,000 E2-LT 2M 4,000 *2 4,000 *2 4,000 *2,080 5 E2-LTR 2M 4,000 *2 4,000 *2, Side-view 0 E2-T4 2M 4,000 *2 4,000 *2 4,000 *2,800 Right-angle 2 E2-TN 2M + E9-F 4,000 *2 4,000 *2 4,000 *2 2,000 6 E2-TN 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2,600 2 E2-TR 2M + E9-F 4,000 *2 4,000 *2 4,000 *2 2,000 6 E2-TR 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2,600 Side-view 60 E2-TR 2M + E9-F2 2,70, E2-T 2M + E9-F 4,000 *2 4,000 *2 4,000 *2,860 6 E2-T 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2 4,000 *2 Side-view 60 E2-T 2M + E9-F2,450,980, E2-T5R 2M + E9-F 4,000 *2 4,000 *2 4,000 *2,500 6 E2-T5R 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2 4,000 *2 Side-view 60 E2-T5R 2M + E9-F2 2,00, E2-T8R-S 2M + E9-F 4,000 *2 4,000 *2 4,000 *2,000 6 E2-T8R-S 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2,800 Side-view 60 E2-T8R-S 2M + E9-F2, E2-T6-S 2M + E9-F 4,000 *2 4,000 *2 4,000 *2,800 6 E2-T6-S 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2,00 Side-view 60 E2-T6-S 2M + E9-F2 2,520, E2-T5 2M + E9-F- 4,000 *2 4,000 *2,450,400 6 E2-T5 2M + E9-F6 4,000 *2 4,000 *2 4,000 *2 4,000 *2 4 E2-D6 2M 40 to 4,000 *2 40 to 2,00 40 to,50 40 to 480 direction Side-view Aperture angle s Giga distance (mm) Standard.5 E2-A0 2M E2-A0-2M 4,000 * 2,670, E2-A04 2M,920, E2-T24SR 2M 4,000 *,00 2, E2-T24S 2M 4,000 *,900 2, E2-T22S 2M 4,000 * 4,000 *,750,000 direction Flat-view Giga distance (mm) Standard E2-L6-N 2M 0 to 5 0 to 2 E2-L24S 2M 0 to 4 Side-view E2-L25L 2M 5.4 to 9 (center 7.2) Transparent Object Detection (Retro-reflective s) Retro-reflective Feature Size s Giga distance (mm) Standard Limitedreflective E2-C 2M + Film detection M E9-FR + E9-RP7 Square --- E2-R6 5M 50 to,500 Threaded Hex-shaped M6 E2-R2 2M 0 to 70 0 to 250 E2-LRNP 2M + E9-RP 2,020,800,

11 Transparent Object Detection (Limited-reflective s) Limitedreflective Feature direction Small size Flat-view distance (mm) Giga Standard Super-high-speed E2-L24S 2M 0 to 4 Standard E2-L6-N 2M 0 to 5 0 to 2 Glass substrate alignment, 70 C E2-A08 2M 0 to Standard/long-distance E2-A2 2M 2 to Side-view form Side-view E2-L25L 2M 5.4 to 9 (center 7.2) Glass substrate mapping, 70 C E2-A09 2M 5 to Chemical-resistant, Oil-resistant s Type direction distance (mm) Giga Standard Super-high-speed Oil-resistant Right-angle E2-TNF 2M 4,000 * 4,000 * 4,000 * 2,200 Chemical/oil-resistant Chemical/oil-resistant at 50 C E2-T2F 2M 4,000 * 4,000 * 4,000 *,600 E2-TF 2M 4,000 * 4,000 *,900,000 Side-view E2-T4F 2M 2,00, E2-T5F 2M 4,000 * 4,000 * 2, Semiconductors: Cleaning, developing, and etching; 60 C E2-LFP 5M 8 to 20 mm from tip of lens (Recommended sensing distance: mm), 9 to mm from center of mounting hole A (Recommended sensing distance: 22 mm) Reflective Semiconductors: Resist stripping; 85 C E2-LFS 5M 8 to 20 mm from tip of lens (Recommended sensing distance: mm), 2 to 44 mm from center of mounting hole A (Recommended sensing distance: 5 mm) Chemical/oil-resistant E2-D2F 2M --- * Chemical-resistant cable E2-DU 2M, *. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. *2. Even if there is no sensing object, the Sensor will detect light that is reflected by the fluororesin. Bending-resistant s Size distance (mm) Giga Standard Super-high-speed.5 dia. E2-T22B 2M, M E2-T2 2M M4 E2-T 2M,750 2,020,50 60 Square 2-T25XB 2M Reflective.5 dia. E2-D22B 2M M E2-D2 2M dia. E2-D22B 2M M4 E2-D2B 2M M6 E2-D 2M, Square E2-D25XB 2M Heat-resistant s Reflective Heat-resistant temperature *. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. distance (mm) Giga Standard Super-high-speed 00 C E2-T5R 2M 2,400, C E2-T5 2M 4,000 * 2,250, C E2-T8R-S 2M, C E2-T6-S 2M 2,520, C E2-D5R 2M, C E2-D5 2M, C E2-D8R-S 2M C E2-A08H2 2M 0 to E2-A09H2 2M 20 to 0 (center 25) --- E2-D6-S 2M 50 C E2-D6-S 2M C E2-D7-S 2M

12 Area Detection s *. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. Liquid-level Detection s Vacuum-resistant s Type width *. The fiber length is m on each side, so the sensing distance is given as 2,000 mm. s for FPD, Semiconductors, and Solar Cells *. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. distance (mm) Giga Standard Super-high-speed E2-T6PR 2M 4,000 * 2,550, mm Area E2-T6JR 2M 4,000 * 2,250, mm E2-T6WR 2M 4,000 *,900 2, Reflective Array mm E2-D6P 2M, Tube-mounting Liquid contact (heat-resistant up to 200 C) Limitedreflective Tube diameter Feature.2, 6.4, or 9.5 dia 8 to 0 dia Stable residual quantity detection Mounting at multiple levels E2-A0 5M E2-L25T 2M distance (mm) Giga Standard Super-high-speed Applicable tube: Transparent tube with a diameter of.2, 6.4, or 9.5 mm, Recommended wall thickness: mm Applicable tube: Transparent tube with a diameter of 8 to 0 mm, Recommended wall thickness: mm No restrictions Large tubes E2-D6T 5M Applicable tube: Transparent tube (no restrictions on diameter) E2-D82F 4M Liquid-contact type Heat-resistant temperature Application distance (mm) Giga Standard Super-high-speed E2-T5V M, C E2-T5V M + E9-FV 2,000 * 2,000 * 2,000 * C E2-T84SV M 2,000 *, Operating temperature Glass presence detection 70 C Glass substrate alignment Glass substrate mapping Wet processes: Cleaning, Resist developing and etching Wet process: Resist stripping Wafer mapping 70 C distance (mm) Giga Standard Super-high-speed E2-L6-N 2M 0 to 5 0 to 2 E2-A08 2M 00 C E2-A08H2 M 0 to E2-A2 2M 2 to C E2-A09 2M 5 to C E2-A09H2 2M 20 to 0 (center 25) C E2-LFP 5M 85 C E2-LFS 5M 8 to 20 mm from tip of lens (Recommended sensing distance: mm), 9 to mm from center of mounting hole A (Recommended sensing distance: 22 mm) 8 to 20 mm from tip of lens (Recommended sensing distance: mm), 2 to 44 mm from center of mounting hole A (Recommended sensing distance: 5 mm) E2-A0 2M E2-A0-2M 4,000 * 2,670, E2-A04 2M,920, E2-T24SR 2M 4,000 *,00 2, E2-T24S 2M 4,000 *,900 2,

13 Infrared ls Threaded s Reflective Cylindrical s direction Size Right-angle Straight Straight Size M4 E2-TN 2M E2-TR 2M Giga distance (mm) Standard M E2-C 2M M6 direction E2-DR 2M E2-CC200 2M Giga distance (mm) Standard E2-T2R 2M dia. Side-view E2-T4LR 2M Reflective dia. E2-D2L 2M Flat s Reflective direction Giga distance (mm) Standard E2-T5XR 2M Side-view E2-T5YR 2M Flat-view E2-T5ZR 2M E2-D5XR 2M Side-view E2-D5YR 2M Flat-view E2-D5ZR 2M Sleeve s distance (mm) direction Giga Standard E2-TC200BR 2M Reflective E2-DC200BR 2M High-power Beam s Type direction Aperture angle s ls with integrated lens Giga distance (mm) Standard Side-view 0 E2-T4 2M

14 ENX-FA I/O Circuit Diagrams NPN Operation Light- ENX-FA ENX-FA6 ENX-FA-5 ENX-FAH ENX-FAH6 Timing chart (Between brown and Dark- (Between brown and Light- ch/ ch2 (Between brown and black leads) ENX-FA2 Dark- ch/ ch2 (Between brown and black leads) Light- (Between brown and ENX-FA7 ENX-FA24 Dark- Light- ENX-FA7TW (Between brown and ch/ ch2 (Between brown and black leads) Dark- ch/ ch2 (Between brown and black leads) Light- (Between brown and L/D indicator L lit. Dark- Display OUT indicator Brown Black Control output Photoelectric sensor main circuit 0 to 0 VDC Blue D lit. L lit. Display OUT indicator OUT2 indicator Brown Black Control output Orange ch Control output ch2 Pink Photoelectric sensor main circuit 0 to 0 VDC External input Blue D lit. Display OUT indicator L lit. 4 Photoelectric sensor main circuit D lit. M8 Connector Pin Arrangement 2 L lit. Display OUT indicator OUT2 indicator Photoelectric sensor main circuit Brown Black Control output 0 to 0 VDC 2 Orange External input Blue 4 Brown Black Control output Orange ch Control output ch2 0 to 0 VDC Blue D lit. L lit. Display OUT indicator Brown Black Photoelectric sensor main circuit ENX-FAAN (Between brown and circuit Control output Orange Analog output 0kΩ min. 0 to 0 VDC Blue D lit. 4

15 ENX-FA PNP Operation Light- ENX-FA4 ENX-FA8 ENX-FAH4 ENX-FAH8 Timing chart L/D indicator L lit. circuit Display OUT indicator (Between blue and Dark- Brown Control Black output Photoelectric sensor main circuit 0 to 0 VDC Blue D lit. (Between blue and Light- ch/ ch2 L lit. OUT indicator (Between blue and black leads) ENX-FA5 Dark- ch/ ch2 s Display OUT2 indicator Brown External Pink input Control output Black ch Control output Orange ch2 Photoelectric sensor main circuit Blue 0 to 0 VDC D lit. (Between blue and black leads) Light- Display OUT indicator L lit. 2 Photoelectric sensor main circuit (Between blue and ENX-FA9 ENX-FA54 Dark- 4 External Orange input Control Black output 0 to 0 VDC D lit. Brown M8 Connector Pin Arrangement 2 Blue 4 (Between blue and Light- ch/ ch2 Display L lit. (Between blue and black leads) ENX-FA9TW ENX-FA54TW Dark- ch/ ch2 s OUT2 indicator OUT indicator Control output Black ch Control output Orange ch2 2 Photoelectric sensor main circuit 4 D lit. Brown M8 Connector Pin Arrangement 2 Blue 0 to 0 VDC 4 (Between blue and black leads) Light- L lit. Dark- Brown Orange Analog output (Between blue and Photoelectric sensor main circuit ENX-FA4AN Display OUT indicator 0 to 0 VDC Black Control output Blue 0kΩ min. D lit. (Between blue and 5

16 Plug (Sensor I/O Connector) 4 2 Terminal number 2 4 XSF-M A XSF-M A XSF-M A XSF-M A Wire color Brown White Blue Black Wire color Connection pin Application Brown Power supply (+V) White 2 External input / Blue Power supply (0 V) Black 4 Nomenclature ENX-FA/FA4/FA6/FA8/FA7/FA9/FA24/FA54/ FA-5/FAH/FAH4/FAH6/FAH8/FAAN/FA4AN [L/D Indicator] Indicates the setting status: Light- (L) or Dark- (D). [OUT Indicator] Turns when the output is. [DPC Indicator] Turns when Dynamic Power Control is effective. [ST Indicator] Turns when Smart Tuning is in progress. [ L/D Button] Use to switch between Light- (L) and Dark- (D). [ Tune Button] Threshold Level Green digital display Executes Smart Tuning. Incident Level White digital display [ MODE Button] Use to switch between Detection Mode and Setting Mode. [+ UP/DOWN Button] Used to fine-tune the threshold or change set values. ENX-FA2/FA5/FA7TW/FA9TW/FA54TW/FA0/FA40/FA0/FAH0 [L/D Indicator] Indicates the setting status: Light- (L) or Dark- (D). [OUT Indicator/OUT2 Indicator] Turns when OUT or OUT2 is. * [DPC Indicator] Turns when Dynamic Power Control is effective. [ST Indicator] Turns when Smart Tuning is in progress. [ L/D Button] Use to switch between Light- (L) and Dark- (D). [ Tune Button] Executes Smart Tuning. * Only OUT turns for output. Threshold Level Green digital display [OUT Selection Indicator/OUT2 Selection Indicator] The indicator for the selected output channel is lit. * Incident Level White digital display [ MODE Button] Use to switch between Detection Mode and Setting Mode, and use to switch between OUT and OUT2. (2 outputs) [+ UP/DOWN Button] Used to fine-tune the threshold or change set values. 6

17 Safety Precautions Be sure to read the precautions for all ls in the website at: Warning Indications WARNING Precautions for Safe Use Precautions for Correct Use Warning level Indicates a potentially hazardous situation which, if not avoided, will result in minor or rate injury, or may result in serious injury or death. Additionally, there may be significant property damage. Supplementary comments on what to do or avoid doing, to use the product safely. Supplementary comments on what to do or avoid doing, to prevent failure to operate, malfunction or undesirable effect on product performance. Meaning of Product Safety Symbols General prohibition Indicates the instructions of unspecified prohibited action. Caution, explosion Indicates the possibility of explosion under specific conditions. Caution, fire Indicates the possibility of fire under specific conditions. WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Do not use the product with voltage in excess of the rated voltage. Excess voltage may result in malfunction or fire. Never use the product with an AC power supply. Otherwise, explosion may result. Precautions for Safe Use ENX-FA The following precautions must be observed to ensure safe operation of the Amplifier Unit. Doing so may cause damage or fire.. Do not install the product in the following locations. Locations subject to direct sunlight Locations subject to condensation due to high humidity Locations subject to corrosive gas Locations subject to vibration or mechanical shocks exceeding the rated values Locations subject to exposure to water, oil, chemicals Locations subject to stream Locations subjected to strong magnetic field or electric field 2. Do not use the product in environments subject to flammable or explosive gases.. Do not use the product in any atmosphere or environment that exceeds the ratings. 4. To secure the safety of operation and maintenance, do not install the product close to high-voltage devices and power devices. 5. High-voltage lines and power lines must be wired separately from the product. Wiring them together or placing them in the same duct may cause induction, resulting in malfunction or damage. 6. Do not apply any load exceeding the ratings. Otherwise, damage or fire may result. 7. Do not short the load. Otherwise, damage or fire may result. 8. Connect the load correctly. 9. Do not miswire such as the polarity of the power supply. 0.Do not use the product if the case is damaged..burn injury may occur. The product surface temperature rises depending on application conditions, such as the ambient temperature and the power supply voltage. Attention must be paid during operation or cleaning. 2.When setting the sensor, be sure to check safety such as by stopping the equipment..be sure to turn off the power supply before connecting or disconnecting wires. 4.Do not attempt to disassemble, repair, or modify the product in any way. 5.When disposing of the product, treat it as industrial waste. 6.Do not use the Sensor in water, rainfall, or outdoors. 7.Use the product in the IP54 enclosure. 8.UL Standard Certification (Applicable s: ENX-FA/2/4/5 Only) Only the sensors with Enhanced UL Certification Mark are certified by UL. They are intended to be supplied by a "Class 2 circuit". When used in United States and Canada, Please use the same Class 2 source for input and output.the overcurrent protection current rating is 2A max. They were evaluated as Open type and shall be installed within a enclosure. 7

18 Precautions for Correct Use. Be sure to mount the unit to the DIN track until it clicks. 2. When using the Amplifier Units with Wire-saving Connectors, attach the protective stickers (provided with EX-CN-series Connectors) on the unused power pins to prevent electrical shock and short circuiting. When using the Amplifier Units with Connectors for Communications Units, attach the protective caps (provided with ENW-series Sensor Communications Unit). Amplifier Unit with Wiresaving Connector Amplifier Unit with Connector for Communications Unit Protective sticker Power supply connecting terminals Protective cap. The length for the cable extension must be 0 m or less (or less than 0 m for S-mark certified ls). Be sure to use a cable of at least 0. mm 2 for extension. The power voltage must be 24 to 0 V when connecting amplifier units with extension cable and wire-saving connector. 4. Do not apply the forces on the cord exceeding the following limits: Pull: 40N; torque: 0.N m; pressure: 20N; bending: 29.4N 5. Do not apply excessive force such as tension, compression or torsion to the Amplifier Unit with the Fiber Unit fixed to the Amplifier Unit. 6. Always keep the protective cover in place when using the Amplifier Unit. Not doing so may cause malfunction. 7. It may take time until the received light intensity and measured value become stable immediately after the power is turned on depending on use environment. 8. The product is ready to operate 200 ms after the power supply is turned. 9. The Mobile Console EX-MC, EX-MC-SV2 and EX-MC- S cannot be connected. 0.The mutual interference prevention function does not work when in combination with EC/E2C/EX..If the unit receives excessive sensor light, the mutual interference prevention function may not work properly, resulting in malfunction of the unit. In such case, increase the threshold. 2.Standard ls and Advanced ls The Sensor Communication Unit EX-DRT2-S, EX-CRT, EX- ECT and ENW cannot be connected. for Sensor Communication Unit (ENX-FA0) The Sensor Communication Unit ENW can be connected. EX-DRT2-S, EX-CRT, EX-ECT cannot be connected..if you notice an abnormal condition such as a strange odor, extreme heating of the unit, or smoke immediately stop using the product, turn off the power, and consult your dealer. 4.Do not use thinner, benzene, acetone, and lamp oil for cleaning. 8

19 Dimensions Fiber Amplifier Units ENX-FA (Unit: mm) Tolerance class IT6 applies to dimensions in this data sheet unless otherwise specified. Pre-wired Amplifier Units ENX-FA(-5)/FA4/ L/D indicator DPC indicator ST indicator OUT2 selection indicator 2 OUT2 indicator OUT indicator ENX-FA2/FA L/D indicator DPC indicator ST indicator *Cable Specifications ENX-FA4 ENX-FAH@ ENX-FA@AN ENX-FA2 ENX-FA5 Outer diameter No. of conductors 4.0 dia. 4.0 dia. 5 Others Conductor cross-section: 0.2 mm 2 Insulator dia.: 0.9 mm Standard cable length: 2 m Minimum bending radius: 2 mm 0 OUT indicator Threshold level (green, digital) 5. Incident level (white, digital) Mounted to DIN Track OUT selection indicator Threshold level (green, digital) 47. (max. value with cover open) 70 (max. value with cover open) Incident level (white, digital) 5. With Mounting Bracket Attached (max. value with cover open) 4.5 Two, 2.4-dia..5.5 fiber unit holes (6.5) (7) (6.5) (7) * * Fiber Attachment (E9-F9) attached 20.5 (7.9) 7.8 (20.) Optical communications Two,.2 dia. (mounting holes) 20.5 (9.4) 6 4. Optical communications E9-L4 Mounting Bracket (sold separately, SUS04) PFP-@N DIN Track (sold separately) Mounting Holes Two, M holes 6 (29.9) 6 Amplifier Units with Wire-saving Connectors ENX-FA6 ENX-FA7(TW) ENX-FA6/FA7(TW)/FA8 ENX-FA8 /FA9(TW)/FAH6/FAH8 ENX-FA9(TW) DPC indicator ENX-FAH6 ENX-FAH8 L/D indicator OUT indicator Threshold level (green, digital) ST indicator Incident level (white, digital) OUT2 selection indicator ENX-FA7TW/FA9TW 2 OUT2 indicator OUT indicator OUT selection indicator Threshold level (green, digital) 27.8 L/D indicator DPC indicator ST indicator Incident level (white, digital) *Cable Specifications Outer diameter No. of conductors EX-CN2 2.6 dia. EX-CN22 2 EX-CN 4.0 dia. EX-CN2 4 0 Mounted to DIN Track With Mounting Bracket Attached (max. value with cover open) 70 (max. value with cover open) 5. (75.) 04.8 (max. value with cover open) 4.5 Two, 2.4-dia..5 fiber unit holes (6.5) (7).4 * ().5 (6.5) (7).4 * () 5.7 With Fiber Attachment (E9-F9) attached 20.5 (7.9) (2.8) (75.) PFP-@N DIN Track (sold separately) Optical communications Wire-saving Connector (sold separately) Two,.2 dia. (mounting holes) 20.5 (9.4) Wire-saving Connector (sold separately) Optical communications E9-L4 Mounting Bracket (sold separately, SUS04) Mounting Holes Two, M holes (29.9) 6 6 9

20 Amplifier Units with M8 Connectors ENX-FA24 ENX-FA54 ENX-FA54TW ENX-FA24/FA54 L/D indicator DPC indicator ST indicator OUT2 selection indicator OUT2 indicator 2 ENX-FA54TW 27.8 L/D indicator DPC indicator ST indicator 2 Connector pin arrangement OUT indicator OUT indicator Threshold level (green, digital) 5.2 Incident level (white, digital) OUT selection indicator Threshold level (green, digital) Incident level (white, digital) 0 5. Mounted to DIN Track 47. (max. value with cover open) 70 (max. value with cover open) With Mounting Bracket Attached (max. value with cover open) 4.5 Two, 2.4-dia. fiber unit holes.5 (6.5) (5.7) PFP-@N DIN Track (sold separately) 20. Optical communications M8 Connector.4 Two,.2 dia. (mounting holes) (9.4) E9-L4 Mounting Bracket (sold separately, SUS04) Mounting Holes Two, M holes Amplifier Unit with Connector for Sensor Communications Unit ENX-FA0/FAH0 OUT2 selection indicator L/D indicator DPC indicator OUT2 indicator ST indicator OUT indicator OUT selection indicator Threshold level (green, digital) Incident level (white, digital) ENX-FA0/FAH0 40 (max. value with cover open) Mounted to DIN Track 5. ENX-FA0/FA40 40 (max. value with cover open) 52 (max. value with cover open) 52 (max. value with cover open) 04.8 (max. value with cover open) 4.5 Two, 2.4-dia. fiber unit holes.5 (6.5) (7).4 26 (29.9).5 (6.5) (7) (5.7).4 26 (29.9) 5.7 With Fiber Attachment (E9-F9) attached 20.5 (7.9) PFP-@N DIN Track (sold separately) Optical communications (9.) 90.8 With Fiber Attachment (E9-F9) attached 20.5 (7.9) (45.4) PFP-@N DIN Track (sold separately) Optical communications 20

21 Accessories (Sold Separately) Wire-saving Connectors Master Connector EX-CN EX-CN2 Edge of Amplifier Unit (7) 2, * * EX-CN: 4-dia. cable with conductors, Standard cable length: 2 m (Conductor cross-section: 0.2 mm 2 (AWG24), Insulator diameter:. mm) EX-CN2: 4-dia. cable with 4 conductors, Standard cable length: 2 m (Conductor cross-section: 0.2 mm 2 (AWG24), Insulator diameter:. mm) Slave Connector EX-CN2 EX-CN22 Edge of Amplifier Unit (7) 2, * * EX-CN2: 2.6-dia. cable with conductor, Standard cable length: 2 m (Conductor cross-section: 0.2 mm 2 (AWG24), Insulator diameter:. mm) EX-CN22: 4-dia. cable with 2 conductors, Standard cable length: 2 m (Conductor cross-section: 0.2 mm 2 (AWG24), Insulator diameter:. mm) Sensor I/O Connectors Straight XSF-M42-40@-A L-shaped XSF-M422-40@-A 2

22 Mounting Bracket E9-L4 (0.) Mounting Holes Two, M holes dia. holes 7 6±0. 6 Four, Radius: max. 7.4 Material: Stainless steel (SUS04).4 DIN Track PFP-00N PFP-50N ±0.5 5±0. 27± (5)* 0 0,000 (500)* *Dimensions in parentheses are for the PFP-50N. Material: Aluminum PFP-00N ± ,000 Material: Aluminum End Plate PFP-M.5 50 M4 8 panhead screw 0 M4 spring washer Materials: Iron, zinc plating

23 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMR MAKES NO WARRANTY OR REPRESENTATI, EXPRESS OR IMPLIED, ABOUT N-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron s sole obligation hereunder shall be, at Omron s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See or contact your Omron representative for published information. Limitation on Liability; Etc. OMR COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTI OR COMMERCIAL LOSS IN ANY WAY CNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer s application or use of the Product. At Buyer s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATI INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMR PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMR Corporation Industrial Automation Company In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation 208 All Right Reserved.