R Series for PXI Express Digital RIO with Kintex-7 325T FPGA. ni.com/manuals. may impair the protection the NI PXIe-7822R provides.
|
|
- Annice Sutton
- 5 years ago
- Views:
Transcription
1 SPECIFICATIONS NI PXIe-7822R R Series for PXI Express Digital RIO with Kintex-7 325T FPGA Français Deutsch 日本語한국어简体中文 ni.com/manuals This document contains the specifications for the NI PXIe-7822R. Specifications are typical at 25 C unless otherwise noted. Caution Using the NI PXIe-7822R in a manner not described in this document may impair the protection the NI PXIe-7822R provides. Digital I/O Number of connectors 4 Number of channels per connector 32 Maximum frequency 80 MHz Compatibility LVTTL, LVCMOS Logic family Software-selectable Default software setting 3.3 V Table 1. Digital Input Logic Levels Logic Family Input Low Voltage (V IL ) Max Input High Voltage (V IH ) Min 1.2 V 0.42 V 0.84 V 1.5 V 0.51 V 1.01 V 1.8 V 0.61 V 1.21 V
2 Table 1. Digital Input Logic Levels (Continued) Logic Family Input Low Voltage (V IL ) Max Input High Voltage (V IH ) Min 2.5 V 0.70 V 1.60 V 3.3 V 0.80 V 2.00 V Minimum input -0.3 V Maximum input 3.6 V Input leakage current ±15 µa max Input impedance 50 kω typ, pull-down Table 2. Digital Output Logic Levels Logic Family Current Output Low Voltage (V OL ) Max Output High Voltage (V OH ) Min 1.2 V 100 µa 0.20 V 1.00 V 1.5 V 100 µa 0.20 V 1.25 V 1.8 V 100 µa 0.20 V 1.54 V 2.5 V 100 µa 0.20 V 2.22 V 3.3 V 100 µa 0.20 V 3.00 V 4 ma 0.40 V 2.40 V Maximum DC output current per channel... Source 4.0 ma... Sink 4.0 ma Output impedance 50 Ω Power-on state Programmable, by line Protection ±20 V, single line 1 Digital I/O voltage selection Programmable, per connector, and defined at compilation (not run-time configurable) 1 NI recommends minimizing long-term over/under-voltage exposure to the Digital I/O. Prolonged DC voltage stresses that violate the maximum and minimum digital input voltage ratings may reduce device longevity. Over/under-voltage stresses are considered prolonged if the cumulative time in the abnormal condition exceeds 1 year. 2 ni.com NI PXIe-7822R Specifications
3 Direction control of digital I/O Per channel channels Minimum I/O pulse width 6.25 ns Minimum sampling period 5 ns External Clock Direction Input into device Maximum input leakage ±15 µa Characteristic impedance 50 Ω Power-on state Tristated Minimum input -0.3 V Maximum input 3.6 V Logic level Inherited from programmed digital voltage selection per connector Maximum input frequency 80 MHz Reconfigurable FPGA FPGA type Kintex-7 325T Number of flip-flops 202,800 Number of LUTs 101,400 Embedded Block RAM 11,700 kbits Number of DSP48 slices 600 Timebase 10, 40, 80, 100, 120, 160, or 200 MHz Default timebase 40 MHz Timebase reference source PXI Express 100 MHz (PXIe_CLK100) Timebase accuracy ±100 ppm, 250 ps peak-to-peak jitter Data transfers DMA, interrupts, programmed I/O NI PXIe-7822R Specifications National Instruments 3
4 Onboard DRAM Memory size 1 Bank; 512 MB Maximum theoretical data rate 800 MB/s streaming Synchronization Resources Input/output source PXI_Trig<0..7> Input source PXI_Star, PXIe_DStarA, PXIe_DStarB, PXI_Clk10, PXIe_Clk100, External Clock x Output source PXIe_DStarC Bus Interface Form factor x4 PXI Express, specification v1.0 compliant Slot compatibility x4, x8, and x16 PXI Express or PXI Express hybrid slots Data transfers DMA, interrupts, programmed I/O Number of DMA channels 16 Maximum Power Requirements Power requirements are dependent on the digital output loads and configuration of the LabVIEW FPGA VI used in your application VDC (±5%) 3 A +12 V 2 A 4 ni.com NI PXIe-7822R Specifications
5 Physical Characteristics Note If you need to clean the device, wipe it with a dry, clean towel. Dimensions 16 cm by 10 cm (6.3 in. by 3.9 in.) Weight 183 g (0.403 lb) I/O connectors x4 68-pin female high-density VHDCI type Environmental Ambient Operating temperature 0 C to 55 C (IEC , IEC ) Ambient Storage temperature -40 C to 71 C (IEC , IEC ) Operating humidity 10% RH to 90% RH, noncondensing (IEC ) Storage humidity (IEC ) 5% RH to 95% RH, noncondensing Pollution Degree 2 Maximum altitude 2,000 m at 25 C Indoor use only. Shock and Vibration Operational shock 30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC Meets MIL- PRF-28800F Class 2 limits.) Random vibration... Operating 5 Hz to 500 Hz, 0.3 g rms... Non-operating.5 Hz to 500 Hz, 2.4 g rms (Tested in accordance with IEC Meets MIL- PRF-28800F Class 3.) NI PXIe-7822R Specifications National Instruments 5
6 Safety Standards This product meets the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC , EN UL , CSA EN :2012, EN :2010 IEC : Ed 6, IEC : Ed 4 UL : Ed 5, UL : Ed 3 CSA : 2011, CSA : 2012 Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN (IEC ): Class B emissions; Basic immunity EN (CISPR 11): Group 1, Class B emissions EN (CISPR 22): Class B emissions EN (CISPR 24): Immunity AS/NZS CISPR 11: Group 1, Class B emissions AS/NZS CISPR 22: Class B emissions FCC 47 CFR Part 15B: Class B emissions ICES-001: Class B emissions Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes. Note For EMC declarations and certifications, and additional information, refer to the Online Product Certification section. Note In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended for use only in heavy-industrial locations. 6 ni.com NI PXIe-7822R Specifications
7 CE Compliance This product meets the essential requirements of applicable European Directives, as follows: 2014/35/EU; Low-Voltage Directive (safety) 2014/30/EU; Electromagnetic Compatibility Directive (EMC) Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/ certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee. 电子信息产品污染控制管理办法 ( 中国 RoHS) 中国客户 National Instruments 符合中国电子信息产品中限制使用某些有害物质指令 (RoHS) 关于 National Instruments 中国 RoHS 合规性信息, 请登录 ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china.) NI PXIe-7822R Specifications National Instruments 7
8 Worldwide Support and Services The National Instruments website is your complete resource for technical support. At ni.com/ support, you have access to everything from troubleshooting and application development self-help resources to and phone assistance from NI Application Engineers. Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and other services. Visit ni.com/register to register your National Instruments product. Product registration facilitates technical support and ensures that you receive important information updates from NI. A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer s declaration of conformity. This system affords the user protection for electromagnetic compatibility (EMC) and product safety. You can obtain the DoC for your product by visiting ni.com/certification. If your product supports calibration, you can obtain the calibration certificate for your product at ni.com/calibration. National Instruments corporate headquarters is located at North Mopac Expressway, Austin, Texas, National Instruments also has offices located around the world. For telephone support in the United States, create your service request at ni.com/support or dial ASK MYNI ( ). For telephone support outside the United States, visit the Worldwide Offices section of ni.com/niglobal to access the branch office websites, which provide up-to-date contact information, support phone numbers, addresses, and current events. 8 ni.com NI PXIe-7822R Specifications
9 NI PXIe-7822R Pinout External Clock x* DIO0 DIO DIO1 DIO3 TERMINAL 68 TERMINAL 34 CONNECTOR 0 (RDIO) CONNECTOR 3 (RDIO) TERMINAL 35 TERMINAL 1 DIO DIO5 DIO DIO7 DIO DIO9 DIO DIO11 TERMINAL 1 TERMINAL 35 TERMINAL 34 TERMINAL 68 DIO DIO13 DIO DIO15 DIO DIO17 DIO DIO19 TERMINAL 68 TERMINAL 35 DIO20 DIO22 DIO24 DIO26 DIO DIO21 DIO23 DIO25 DIO27 DIO29 TERMINAL 34 TERMINAL 1 TERMINAL 35 TERMINAL 1 TERMINAL 34 TERMINAL 68 DIO DIO31 * x is the connector number. External Clock x is an input only. CONNECTOR 1 (RDIO) CONNECTOR 2 (RDIO) NI PXIe-7822R Specifications National Instruments 9
10 Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR , DFAR , and DFAR National Instruments. All rights reserved B-01 Jun15
USB Contents. Definitions SPECIFICATIONS. RF Power Sensor Device
SPECIFICATIONS USB-5680 RF Power Sensor Device Contents Definitions...1 Conditions... 2 General... 2 Uncertainty...3 System...4 Maximum Damage Levels... 5 DC Power Requirements (5V) through Host US...
More informationTopology 1-wire 16 Bank 8 1, 1-wire Octal 16 1, 1-wire Quad 32 1, 1-wire Dual 64 1, 1-wire 128 1
DEVICE SPECIFICATIONS NI PXIe-2524 Multibank Configurable 1-wire Multiplexer This document lists specifications for the NI PXIe-2524 (NI 2524) multiplexer relay module. All specifications are subject to
More informationThis document lists specifications for the PXI-5691 RF amplifier.
DEVICE SPECIFICATIONS PXI-5691 RF Amplifier This document lists specifications for the PXI-5691 RF amplifier. Specifications are warranted under the following conditions: minutes warm-up time Calibration
More informationThis document lists specifications for the NI PXIe-1491 high-definition multimedia interface (HDMI) analyzer.
DEVICE SPECIFICATIONS NI PXIe-1491 This document lists specifications for the NI PXIe-1491 high-definition multimedia interface (HDMI) analyzer. Specifications are warranted under the following conditions:
More informationSpecifications describe the warranted, traceable product performance over ambient temperature ranges of 0 C to 55 C, unless otherwise noted.
DEVICE SPECIFICATIONS NI PXI-5660 RF Vector Signal Analyzer This document lists specifications for the NI PXI-5660 (NI 5660) RF vector signal analyzer. Specifications are warranted under the following
More information2.7 GHz RF Vector Signal Analyzer with Digital Downconversion. This document lists specifications for the NI PXI-5661 RF vector signal analyzer.
DEVICE SPECIFICATIONS NI PXI-5661 2.7 GHz RF Vector Signal Analyzer with Digital Downconversion This document lists specifications for the NI PXI-5661 RF vector signal analyzer. Specifications are warranted
More informationNI PXI/PXIe-2543 Specifications
NI PXI/PXIe-2543 Specifications 6.6 GHz Dual 4 1 Terminated Solid State Multiplexer (Dual SP4T) This document lists specifications for the NI PXI/PXIe-2543 (NI 2543) multiplexer module. All specifications
More informationSpecification Value Comments
SPECIFICATIONS NI PXIe/PCIe-6535/6536/6537 and NI PCIe-6535B/6536B/6537B 10/25/50 MHz Digital I/O Device This document provides specifications for NI PXIe/PCIe-6535/6536/6537 (NI 6535/6536/6537) and NI
More informationNI R Series Multifunction RIO Specifications
NI R Series Multifunction RIO Specifications This document lists the specifications of the NI 781xR/783xR/784xR/785xR. These specifications are typical at 25 C unless otherwise noted. Français Deutsch
More informationNI 9238 Datasheet DATASHEET. 4 AI, ±500 mv, 24 Bit, 50 ks/s/ch Simultaneous
DATASHEET NI 9238 Datasheet 4 AI, ±500 mv, 24 Bit, 50 ks/s/ch Simultaneous Screw-terminal connectivity Anti-alias filters 250 Vrms, CAT II, channel-to-channel isolation The NI 9238 is a 4-channel analog
More informationNI 9239 DATASHEET. 4 AI, ±10 V, 24 Bit, 50 ks/s/ch Simultaneous
DATASHEET NI 9239 4 AI, ±10 V, 24 Bit, 50 ks/s/ch Simultaneous BNC or screw-terminal connectivity Anti-alias filters 250 Vrms, CAT II, channel-to-channel isolation (screw terminal); 60 VDC, CAT I, channel-to-channel
More informationNI 9260 DATASHEET. 2 AO, 3 Vrms, 24 Bit, 51.2 ks/s/ch Simultaneous
DATASHEET NI 9260 2 AO, 3 Vrms, 24 Bit, 51.2 ks/s/ch Simultaneous BNC and mini-xlr connectivity -105 db THD+N typical 10 µvrms noise typical 23 khz bandwidth The NI 9260 is a 2-channel analog output module
More informationNote In this document, the NI 9202 with spring terminal and the NI 9202 with DSUB are referred to inclusively as the NI 9202.
DATASHEET NI 922 16 AI, ±1 V, 24 bit, 1 ks/s/ch Simultaneous DSUB or push-in spring terminal connectivity 25 V RMS, CAT II, channel-to-earth isolation (spring terminal); 6 V DC, CAT I, channel-to-earth
More informationNI 9244 Datasheet DATASHEET. 3 AI/1 Neutral, 400 Vrms L-N/690 Vrms L-L, 24 Bit, 50 ks/s/ch Simultaneous
DATASHEET NI 9244 Datasheet 3 AI/1 Neutral, 400 Vrms L-N/690 Vrms L-L, 24 Bit, 50 ks/s/ch Simultaneous Screw-terminal connectivity for up to 12 AWG cables Protective backshell 400 Vrms, CAT III, channel-to-earth
More informationUsed for writing unscaled or raw data and covers the range from negative full scale (0) to positive full scale (65,535).
DEVICE SPECIFICATIONS NI PXIe-6739 64-Channel High-Density Analog Output This document lists the specifications for the NI 6739 analog output device. The following specifications are typical at 25 C unless
More informationNI 9251 with mini XLR
DATASHEET NI 9251 with mini XLR 2 AI, 3 Vrms, 24 Bit, 102.4 ks/s/ch Simultaneous, AC/DC Coupling Mini-XLR connectivity -106 dbc THD+N
More informationNI 9246 DATASHEET. 3-Channel, 20 Arms Continuous, 24-Bit, Analog Input Module
DATASHEET NI 9246 3-Channel, 20 Arms Continuous, 24-Bit, Analog Input Module 3 isolated analog input channels, 50 ks/s per channel simultaneous sample rate 22 Arms continuous, ±30 Apeak input range, 24-bit
More informationNI 9230 DATASHEET. 3 AI, ±30 V, 24 Bit, 12.8 ks/s/ch Simultaneous
DATASHEET NI 9230 3 AI, ±30 V, 24 Bit, 12.8 ks/s/ch Simultaneous Screw-terminal or BNC connectivity Software-selectable AC/DC coupling Software-selectable IEPE signal conditioning (0 ma or 4 ma) Smart
More informationDigital Input Modules for Compact FieldPoint
Digital Modules for Compact FieldPoint NI cfp-di-300, NI cfp-di-301, NI cfp-di-304, NI 8-,16-, or 32-channel inputs 24 VDC inputs 4 to 250 VDC inputs 15 to 250 VAC inputs (50/60 Hz AC) 3 to 250 VAC inputs
More informationThermocouple and RTD Modules for Compact FieldPoint
Thermocouple and Modules for Compact FieldPoint NI cfp-tc-120, NI cfp-tc-125, NI cfp--122, NI cfp--124 8 temperature inputs Thermocouple or millivolt 2-, 3-, or 4-wire Built-in signal conditioning between
More informationNI USRP-2950R/2952R/2953R/ 2954R
GETTING STARTED GUIDE NI USRP-2950R/2952R/2953R/ 2954R Universal Software Radio Peripheral This document explains how to install, configure, and test the National Instruments universal software radio peripheral
More informationUSER MANUAL. Inverted Pendulum Experiment CAPTIVATE. MOTIVATE. GRADUATE.
USER MANUAL Inverted Pendulum Experiment Set Up and Configuration CAPTIVATE. MOTIVATE. GRADUATE. c 2012 Quanser Inc., All rights reserved. Quanser Inc. 119 Spy Court Markham, Ontario L3R 5H6 Canada info@quanser.com
More informationSoftware. Documentation. Test Equipment
CALIBRATION PROCEDURE NI PXIe-5694 This document contains the verification and adjustment procedures for the National Instruments PXIe-5694 IF conditioning module (NI 5694). Refer to ni.com/calibration
More informationBNC-2120 INSTALLATION GUIDE. Connector Accessory for Multifunction DAQ Devices
INSTALLATION GUIDE BNC-2120 Connector Accessory for Multifunction DAQ Devices This installation guide describes how to install, configure, and use your BNC-2120 accessory. If you have not already installed
More informationNI PXIe Contents GETTING STARTED GUIDE. 6.6 GHz RF Vector Signal Analyzer with Digital Downconversion
GETTING STARTED GUIDE NI PXIe-5663 6.6 GHz RF Vector Signal Analyzer with Digital Downconversion Note Before you begin, install and configure your chassis and controller. This document explains how to
More informationData Pattern Generator
Data Pattern Generator DG2040 * DG2030 * DG2020A * P3410/P3420 Characteristics DG2040. Features Specs Ordering Information Pricing Information Print Data Sheet (61kB) Request a Quote Output Data Data Rate
More informationFP-AI-112 and cfp-ai-112
FieldPoint Operating Instructions FP-AI-112 and cfp-ai-112 16-Channel, 16-Bit Analog Input Modules These operating instructions describe how to install and use the FP-AI-112 and cfp-ai-112 analog input
More informationNI PXI Contents GETTING STARTED GUIDE. 2.7 GHz RF Vector Signal Analyzer with Digital Downconversion
GETTING STARTED GUIDE NI PXI-5661 2.7 GHz RF Vector Signal Analyzer with Digital Downconversion Note Before you begin, install and configure your chassis and controller. This document explains how to install,
More informationNI PXIe-5668R. Contents GETTING STARTED GUIDE GHz or 14 GHz Vector Signal Analyzer
GETTING STARTED GUIDE NI PXIe-5668R 26.5 GHz or 14 GHz Vector Signal Analyzer Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure,
More informationPXIe-5667 (7 GHz) Contents GETTING STARTED GUIDE. Vector Signal Analyzer
GETTING STARTED GUIDE PXIe-5667 (7 GHz) Vector Signal Analyzer Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and test the PXIe-5667.
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationNI GSM/EDGE+ Toolkit Specifications
NI GSM/EDGE+ Toolkit Specifications Version 1.1 This document lists specifications for the NI GSM/EDGE+ Toolkit. Maximum specifications are derived under the following conditions: 30 minutes warm-up time
More informationDAQ Analog Output Series
DAQ Analog Output Series NI 6738/6739 User Manual NI 6738/6739 User Manual December 2017 375140B-01 Support Worldwide Technical Support and Product Information ni.com Worldwide Offices Visit ni.com/niglobal
More informationFLIR CM82: 600 Amp Power Clamp Meter with VFD Mode
Copyright All rights reserved worldwide. Names and marks appearing herein are either registered trademarks or trademarks of FLIR Systems and/or its subsidiaries. All other trademarks, trade names or company
More informationNI PXIe-5667 (3.6 GHz)
GETTING STARTED GUIDE NI PXIe-5667 (3.6 GHz) Spectrum Monitoring Receiver Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and
More informationPOWER. DA10-M Series. 10 Watts. Data Sheet. Total Power: 10 Watts Input Voltage: Vac # of Outputs: Single, 5 Volts SPECIAL FEATURES
POWER Data Sheet DA10-M Series 10 Watts Total Power: 10 Watts Input Voltage: 90-264 Vac # of Outputs: Single, 5 Volts SPECIAL FEATURES Medical and ITE safeties Switching wallmount power supply Available
More informationPXIe Contents GETTING STARTED GUIDE. 3.6 GHz or 14 GHz Vector Signal Analyzer
GETTING STARTED GUIDE PXIe-5665 3.6 GHz or 14 GHz Vector Signal Analyzer Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and
More informationUSER MANUAL. IP02 Base Unit Experiment. Set Up and Configuration CAPTIVATE. MOTIVATE. GRADUATE.
USER MANUAL IP02 Base Unit Experiment Set Up and Configuration CAPTIVATE. MOTIVATE. GRADUATE. 2012 Quanser Inc., All rights reserved. Quanser Inc. 119 Spy Court Markham, Ontario L3R 5H6 Canada info@quanser.com
More informationFLIR CM82: 600 Amp Power Clamp Meter with VFD Mode
Copyright All rights reserved worldwide. Names and marks appearing herein are either registered trademarks or trademarks of FLIR Systems and/or its subsidiaries. All other trademarks, trade names or company
More informationSupplement. TDS1000 and TDS2000 Series User Manual Specifications Update
Supplement TDS1000 and TDS2000 Series User Manual Specifications Update 071-1858-00 www.tektronix.com 071185800 Copyright Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationUsers Manual. Stroboscope. September 2014
820-2 Stroboscope Users Manual September 2014 2014 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of their respective companies.
More informationMAP110 AC-DC Series Data Sheet
Description Single-Output Model Selection VOLTAGE RANGE OUTPUT CURRENT OUTPUT CURRENT REGULATION REGULATION %p-p (NOTE 1) ACCURACY MAP110-1005 5V 4.95V to 5.50 16A 2 0.2% 1% 1% 5.09V to 5.11V MAP110-1012
More informationR&S ZN-Z154 Calibration Unit Specifications
ZN-Z154_dat-sw_en_3607-0481-22_v0101_cover.indd 1 Data Sheet 01.01 Test & Measurement R&S ZN-Z154 Calibration Unit Specifications 25.06.2014 10:27:09 CONTENTS Definitions... 3 Measurement range... 4 Effective
More informationR&S ZN-Z85 Switch Matrix Specifications
R&S ZN-Z85 Switch Matrix Specifications Data Sheet Version 01.02 CONTENTS Definitions... 3 Block diagrams... 4 Specifications... 5 General features... 5 Performance data... 5 Remote control... 5 Switching
More informationSingle output models feature wide-range output adjustability to meet a wide variety of standard and user-specific output voltage requirements.
RoHS Lead-Solder-Exemption Compliant New 3.3 V and 5 V Output Models Universal Input 85-264 VAC Industry-Standard Footprint: 7.0" x 4.3" x 1.97" (177.8 x 109.2 x 50.0 mm) Input Transient & ESD Compliance
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationSEL-3405 High-Accuracy IRIG-B Fiber-Optic Transceiver
SEL-3405 High-Accuracy IRIG-B Fiber-Optic Transceiver Accurate IRIG-B Over Fiber Optics Major Features and Benefits The SEL-3405 High-Accuracy IRIG-B Fiber-Optic Transceiver can send high-accuracy demodulated
More informationR&S ZV-Z81 Multiport Test Set, models.05/.09/.29 Specifications
ZV-Z81_models5_9_29_dat-sw_en_5213-6864-22_Cover.indd 1 Data Sheet 04.01 Test & Measurement R&S ZV-Z81 Multiport Test Set, models.05/.09/.29 Specifications 17.04.2013 12:47:27 CONTENTS Definitions... 3
More informationElectrical Specifications
18 Watts 1 of 6 Total Power: 18 Watts Input Voltage: 90-264 Vac # of Outputs: Single Interchangeable Plug Special Features Medical and ITE Safeties Switching wallmount power supply Available in interchangeable
More informationNI GSM/EDGE Toolkit Specifications
NI GSM/EDGE Toolkit Specifications Version 1.0 Generation This document lists specifications for the NI GSM/EDGE Toolkit. These specifications are representative and cannot be guaranteed for different
More informationNI 6612 User Manual. November B-01
NI 6612 User Manual NI 6612 User Manual November 2013 374008B-01 Support Worldwide Technical Support and Product Information ni.com Worldwide Offices Visit ni.com/niglobal to access the branch office Web
More informationR&S TS-PFG Function Generator Module Dual-channel arbitrary waveform generator with isolated outputs
TS-PFG_bro_en_0758-0639-12_v0300.indd 1 Product Brochure 03.00 Test & Measurement R&S TS-PFG Function Generator Module Dual-channel arbitrary waveform generator with isolated outputs 28.09.2016 16:05:56
More informationSample. Data Acquisition and Signal Conditioning. Course Manual. Course Software Version 2011 February 2012 Edition Part Number P-01
Data Acquisition and Signal Conditioning Course Manual Course Software Version 2011 February 2012 Edition Part Number 320733P-01 Data Acquisition and Signal Conditioning Copyright 1995 2012 National Instruments
More informationR&S ZN-Z151/-Z152/-Z153 Calibration Unit Specifications
ZN-Z151_152_153_dat-sw_en_3607-0881-22_v0100_cover.indd 1 Data Sheet 01.00 Test & Measurement R&S ZN-Z151/-Z152/-Z153 Calibration Unit Specifications 07.10.2014 11:35:47 CONTENTS Definitions... 3 Measurement
More information100 MHz, 100 MS/s, 14-Bit Digitizer
NI 5122 2 channels simultaneously sampled at 14-bit resolution 100 MS/s real-time and 2.0 GS/s random interleaved sampling 100 MHz bandwidth 50 Ω or 1 MΩ input impedance, software-selectable 200 mv to
More informationNI SC Express. NI PXIe-4300 User Manual. NI PXIe-4300 User Manual. April A-01
NI SC Express NI PXIe-4300 User Manual NI PXIe-4300 User Manual April 2010 373024A-01 Support Worldwide Technical Support and Product Information ni.com National Instruments Corporate Headquarters 11500
More informationInstallation. SAPTF33xx-1xx in the Network. Standard Configuration
SAPTF33xx-1xx in the Network Standard Configuration One Unit A device (SAPTF33xx-100) and one device () are required for the standard configuration. The Unit A device is connected to the while the device
More informationAgilent N9355/6 Power Limiters 0.01 to 18, 26.5 and 50 GHz
Agilent N9355/6 Power Limiters 0.01 to 18, 26.5 and 50 GHz Technical Overview High Performance Power Limiters Broad frequency range up to 50 GHz maximizes the operating range of your instrument High power
More informationLXM23DU10M3X motion servo drive - Lexium 23 - single phase V - 1 kw - I/O
Characteristics motion servo drive - Lexium 23 - single phase 200...255 V - 1 kw - I/O Main Range of product Product or component type Device short name Complementary Format of the drive Network number
More informationR&S ZN-Z103 Calibration Unit Specifications. Data Sheet V02.01
R&S ZN-Z103 Calibration Unit Specifications Data Sheet V02.01 CONTENTS Definitions... 3 Measurement range... 5 Effective system data... 5 General data... 6 Ordering information... 7 2 Rohde & Schwarz R&S
More informationR&S ZVA110 Vector Network Analyzer Specifications
ZVA110_dat-sw_en_5214-4813-22_cover.indd 1 Data Sheet 04.00 Test & Measurement R&S ZVA110 Vector Network Analyzer Specifications 15.11.2013 14:42:28 CONTENTS Definitions... 3 Specifications... 4 Overview...
More informationUser Guide. Centrex Recording Interface
User Guide Centrex Recording Interface Table of Contents Introduction... 2 The Meridian Business Set... 3 Key Numbering Plan (18 button add-on)... 4 Key Numbering Plan (36 button add-on)... 5 Key Numbering
More informationAccess Converter/ 3. Operation Manual. International Headquarters. European Headquarters. B&B Electronics. 707 Dayton Road Ottawa, IL USA
Access Converter/ 3 International Headquarters B&B Electronics Operation Manual 707 Dayton Road Ottawa, IL 61350 USA Phone (815) 433-5100 General Fax (815) 433-5105 Email: support@bb-elec.com Website:
More informationSound and Vibration Data Acquisition
NI 9233, NI 9234 NEW! 24-bit resolution 102 db dynamic range 4 simultaneous analog inputs ±5 V input range Antialiasing filters TEDS read/write Recommended Software LabVIEW Sound and Vibration Toolkit
More informationDAQ. NI 660x User Manual. NI 6601, NI 6602, and NI 6608 Devices. NI 660x User Manual. ni.com/manuals. December C-01
DAQ NI 660x User Manual NI 6601, NI 6602, and NI 6608 Devices NI 660x User Manual Français Deutsch ni.com/manuals December 2012 372119C-01 Support Worldwide Technical Support and Product Information ni.com
More informationR&S RT-Zxx High-Bandwidth Probes Specifications
R&S RT-Zxx High-Bandwidth Probes Specifications Test & Measurement Data Sheet 14.00 CONTENTS Definitions... 3 Probe/oscilloscope chart... 4 R&S RT-ZZ80 transmission line probe... 5 R&S RT-ZS10/-ZS10E/-ZS20/-ZS30
More informationR&S ZND Vector Network Analyzer Specifications
R&S ZND Vector Network Analyzer Specifications year Test & Measurement Data Sheet 02.01 CONTENTS Definitions... 3 Measurement range... 4 Measurement speed... 5 Measurement accuracy... 7 Effective system
More informationDATA SHEET. The Advantys model STBDAI5260 Digital Input Module provides 2 isolated discrete input points that operate on a 115 VAC power source.
Advantys STB Advantys STB Input Module DATA SHEET Description The Advantys model STBDAI5260 Digital Input Module provides 2 isolated discrete input points that operate on a 115 VAC power source. Features
More informationPSI-MOS-RS232/FO 850 E Serial to Fiber Converter
PSI-MOS-RS232/FO 850 E Serial to Fiber Converter perle.com/products/serial-fiber-converters/psi-mos-rs232-fo850e-rs232-to-fiber.shtml Connect RS232 devices to fiber optic cable Extend serial data up to
More information32 Channel CPCI Board User Manual
0 Sections Page 1.0 Introduction 1 2.0 Unpacking and Inspection 1 3.0 Hardware Configuration 1 4.0 Board Installation 5 5.0 I/O Connections and the Front Panel 5 5.1 Front Panel Layout 5 5.2 Input and
More informationR&S TS-PIO4 Digital Functional Test Module 32-channel programmable digital I/O module
TS-PIO4_bro_en_3607-3474-12_v0100.indd 1 Product Brochure 01.00 Test & Measurement R&S TS-PIO4 Digital Functional Test Module 32-channel programmable digital I/O module 07.07.2016 07:41:56 R&S TS-PIO4
More informationR&S TS-PMB Switch Matrix Module High-density, 90-channel, full matrix relay multiplexer module
TS-PMB_bro_en_0758-0600-12.indd 1 Product Brochure 02.00 Test & Measurement Switch Matrix Module High-density, 90-channel, full matrix relay multiplexer module Switch Matrix Module At a glance Typical
More informationWVR500 Waveform/Vector Monitor
Service Manual WVR500 Waveform/Vector Monitor 070-8897-01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are
More information3500/42E Vibration Monitor
3500/42E Vibration Monitor Bently Nevada* Asset Condition Monitoring Description The 3500/42E Vibration Monitor is a 4-channel monitor that accepts input from proximity and seismic transducers, conditions
More informationNI WCDMA/HSPA+ Toolkit Specifications
NI WCDMA/HSPA+ Toolkit Specifications Version 1.0 Generation This document lists specifications for the NI WCDMA/HSPA+ Toolkit. These specifications are representative and cannot be guaranteed for different
More informationV6118 EM MICROELECTRONIC - MARIN SA. 2, 4 and 8 Mutiplex LCD Driver
EM MICROELECTRONIC - MARIN SA 2, 4 and 8 Mutiplex LCD Driver Description The is a universal low multiplex LCD driver. The version 2 drives two ways multiplex (two blackplanes) LCD, the version 4, four
More informationData Pattern Generator
Features & Benefits Data Rate to 1.1 Gb/s Tests High-speed Logic Devices and Circuits Data Pattern Depth to 256 K/Channel Speeds Characterization Multiple Output Channels Increases Flexibility DG2040:
More informationAdvantys STB DATA SHEET. Advantys STB Output Module. Description. Features
Advantys STB Advantys STB Output Module DATA SHEET Description The Advantys model STBDAO5260 Digital Output Module provides 2 isolated discrete output points that operate on a 115 VAC power source. The
More informationOM2000N INSTALLATION MANUAL
OM2000N INSTALLATION MANUAL 2 1 Figure A 1 2 Laser Beam Output Window Power Cable 821001342 (Rev. B) DESCRIPTION The OM2000N oscillating mirror is an accessory for the 2000N family laser scanners: DS2100N,
More informationSignalOn Series. L-Band Power Inserter Module INSTALLATION & OPERATION MANUAL. 1.2 GHz. D3.
SignalOn Series D3.1/CCAP Compliant 1.2 GHz L-Band Power Inserter Module INSTALLATION & OPERATION MANUAL www.atxnetworks.com www.atxnetworks.com Although every effort has been taken to ensure the accuracy
More informationEX-IQ-Box Digital Signal Interface Module Specifications
Test & Measurement Data Sheet 01.01 EX-IQ-Box Digital Signal Interface Module Specifications Introduction The R&S EX-IQ-Box is a digital interface module that provides flexible digital baseband inputs
More informationBNC-2090A QUICK START GUIDE. Rack-Mount Connector Accessory for E/M Series DAQ Devices
QUICK START GUIDE BNC-090A Rack-Mount Connector Accessory for E/M Series DAQ Devices The National Instruments BNC-090A is a desktop or rack-mount analog breakout accessory you can connect to E/M Series
More informationSpecifications. Reference Documentation. Performance Conditions
The material in this section is organized into two main groupings: the specification tables and the supporting figures. The specification tables include: 1. PAL general and test signal specifications 2.
More informationData Pattern Generator DG2020A Data Sheet
Data Pattern Generator DG2020A Data Sheet DG2000 Series Features & Benefits Data Rate to 200 Mb/s Data Pattern Depth 64 K/channel Speeds Characterization Multiple Output Channels Increases Flexibility
More informationcdaqtm-9185/9189 User Manual 4-Slot and 8-Slot, Extended Temperature, Ethernet CompactDAQ Chassis cdaq-9185/9189 User Manual May A-01
cdaqtm-9185/9189 User Manual 4-Slot and 8-Slot, Extended Temperature, Ethernet CompactDAQ Chassis cdaq-9185/9189 User Manual May 2017 376610A-01 Worldwide Technical Support and Product Information ni.com
More informationSmart Cameras for Embedded Machine Vision
NI 17xx Smart Cameras NEW! Real-time machine vision High-quality monochrome VGA (640x480) or SXGA (1280x1024) CCD image sensors High-performance embedded processors Isolated 24 V digital I/O Dual gigabit
More informationBluetooth Tester CBT. Specifications. Specifications. Version January 2006
Specifications Version 03.00 Bluetooth Tester CBT January 2006 Specifications CONTENTS UNIT SPECIFICATIONS...3 TIMEBASE TCXO...3 REFERENCE FREQUENCY INPUT...3 RF GENERATOR...3 RF ANALYZER...5 Power meter
More informationNI cdaq -9181/9184/9188/9191
TM NI cdaq -9181/9184/9188/9191 User Manual NI CompactDAQ Ethernet and Ethernet/Wireless Chassis NI cdaq-9181/9184/9188/9191 User Manual February 2017 372780K-01 Support Worldwide Technical Support and
More informationAgilent 87405C 100 MHz to 18 GHz Preamplifier
Agilent 8745C 1 MHz to 18 GHz Preamplifier Technical Overview Key Features Rugged, portable design for ease of use in the field Probe-power bias connection eliminates the need for an additional power supply
More informationModel Number Structure
Cycle Control Units CSM DS_E_7_1 Refer to Safety Precautions for All Power Controllers. Used in Combination with the to Enable High-precision Temperature Control Use cycle control to achieve power control
More informationPicoScope 2000 Series PC Oscilloscopes
PicoScope 2000 Series PC Oscilloscopes User guide I PicoScope 2000 Series User Guide Table of Contents 1 Introduction...2...2 1 Overview...2 2 Safety symbols...3 3 Safety warning...3 4 FCC notice 5 CE
More informationIndustriefunkuhren. Technical Manual. IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C / AFNOR NF S87-500
Industriefunkuhren Technical Manual IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C37.118 / AFNOR NF S87-500 Module 7628 ENGLISH Version: 02.01-06.03.2013 2 / 20 7628 IRIG-B
More informationR&S EDS300 DME/Pulse Analyzer Specifications
R&S EDS300 DME/Pulse Analyzer Specifications year Data Sheet Version 04.01 CONTENTS Definitions... 3 Specifications... 4 Frequency... 4 Level... 4 DME signal analysis... 4 TACAN signal analysis (R&S EDS-K1
More informationSTBART0200K standard analog input kit STB - 2 I - 15 bits + sign
Product data sheet Characteristics STBART0200K standard analog input kit STB - 2 I - 15 bits + sign Main Range of product Product or component type Kit composition Analogue input type Analogue input number
More informationModel 7330 Signal Source Analyzer Dedicated Phase Noise Test System V1.02
Model 7330 Signal Source Analyzer Dedicated Phase Noise Test System V1.02 A fully integrated high-performance cross-correlation signal source analyzer from 5 MHz to 33+ GHz Key Features Complete broadband
More informationPAM-1840 Preamplifier Operation Manual
PAM-1840 Preamplifier Operation Manual 1 TABLE OF CONTENTS INTRODUCTION 3 GENERAL INFORMATION 4 SPECIFICATIONS 4 OPERATING INSTRUCTIONS 5 MAINTENANCE 6 2 INTRODUCTION BEFORE APPLYING POWER Review this
More informationR&S TS-ISC In-System Calibration Kit On-site calibration solution for R&S CompactTSVP
TS-ISC_bro_en_5214-1972-12.indd 1 Product Brochure 02.00 Test & Measurement R&S TS-ISC In-System Calibration Kit On-site calibration solution for R&S CompactTSVP 24.09.2013 10:08:56 R&S TS-ISC In-System
More informationHD-One DX/DX500 HDMI Extender
HD-One DX/DX500 HDMI Extender User Manual Version 2.0 tvone 2791 Circleport Drive, Erlanger, KY 41018, USA. Americas: 859-282-7303 EMEA: +44 (0) 1843 873322 Email: tech.usa@tvone.com www.tvone.com CSG-DX-500
More information74F273 Octal D-Type Flip-Flop
Octal D-Type Flip-Flop General Description The 74F273 has eight edge-triggered D-type flip-flops with individual D inputs and Q outputs. The common buffered Clock (CP) and Master Reset (MR) inputs load
More information