Gel-sealed in-line fiber optic closure
|
|
- Marsha Henderson
- 3 years ago
- Views:
Transcription
1 SCIL-C Gel donut INSTALLATION INSTRUCTION TC IP Rev A, Oct Gel-sealed in-line fiber optic closure Contents 1 General 2 Sizing and product kit information 3 Installation conditions precautions 4 Cable preparation 5 Cable installation 6 Fiber preparation 7 Splicing and fiber storage 8 Hanger bracket installation 9 Re-entry 1 General 1.1 Installation Instruction description The installation instruction describes the necessary steps to install the SCIL-C. The installation instruction illustrates the use on loose tube cables. If other cable types are used, please contact the local agent for relevant accessories and instructions. 1.2 Product description The SCIL-C is a gel sealed fiber optic splice closures designed for cable joint applications in the telecom outside plant network. The closures have maximum splicing capacity of 144F and are suitable for deployment in aerial, underground or direct buried environments. Sealing is achieved visa built-in gel technology, resulting in extremely convenient re-entry and re-sealing. The closure has six cable ports, three on each side. 2 Sizing and product kit information 2.1 Dimensions Cable diameter range Closure outer dimensions 7~8mm, 10~13mm, 14~16 mm 350 x 216 x140 mm
2 2.2 Kit content 4 Cable preparation 4.1 Open the closure, as shown * Below listed is a standard kit, alternative kits and accessories Take the films away (optional) are available. 1. Cover and base with latches 2. Splice tray kit (optional) 3. Splice tray lid (optional) 4. Velcro 5. Transportation tubes (optional) 6. Cable fixation bracket (2 pcs) 7. Hanger brackets and screw (optional) 8. Clamp kit (Large) (optional) 9. Ring Tree (Large) (optional) 10. Clamp kit(small) (optional) 11. Ring Tree (small) (optional) 12. Gel donut A (optional) 13. Gel donut B (optional) 14. Gel donut C (optional) 15. Dummy rods (optional) 16. White tie wraps (optional) 17. Black tie wraps (optional) 18. Tray holder (optional) 19. Cleaning tissue 20. Installation instruction 3 Installation conditions precautions 3.1 The closures should be installed at temperature between -5 C and 45 C. 4.2 Take the films away (optional) and open the Velcro and tray kit. 4.3 Unscrew the upper clamps where you will install the cable. Note: Prefer to use manual screwdriver or electric screwdriver in low speed. 3.2 Follow the installation instruction steps to ensure the performance of the closure. 3.3 It is necessary to take precautions and keep the working space clean to protect the closure sealing materials and splices. 2
3 4.4 Take out upper clamps and gel donut along with the dummy rods. Note 3: For Gel donut C:. 4.5 According to the cable range to choose the appropriate Gel donut. Cable range Gel donut (mm) 7-12(small cable) A 12-16(big cable) B 10-16(big cable) C 4.7 According to the cable range and cable quantity to be installed on each port, choose the appropriate cable clamp and remove the equivalent TPE sleeve layer installed on the lower clamp (refer to Table 2). Cable Remove Cable qty Cable range TPE sleeve on each clamp (mm) layer. port 7-8 Small 0 1 or Small Small Large Large 1 1 Table 2, Cable clamp selection Table 1, Gel donut selection Big clamp type: Clamp with plastic upper clamps: 4.6 Separate the gel donut and dummy rod, as shown Note 1: For Gel donut A: Clamp with metal upper clamps: Note 2: For Gel donut B: Small lower clamp: 0 TPE sleeve removed 1 TPE sleeve removed 2 TPE sleeve removed 3
4 Big lower clamp: Note 2: For only one small cable installation, snap 1 dummy rod off, as shown. 0 TPE sleeve removed 1 TPE sleeve removed 4.8 Leave the lower clamps, as shown. For install small cable, remove one small lower clamp, as shown. Note 3: For install big cable, separate dummy rod and blocking ring, as shown For install big cable, replace two small lower clamps (refer to Table 2) with one big lower clamp, as shown. 1) Install the Gel donut B or C as following. 2) Select the appropriate blocking ring from the block tree, according to the cable outer diameter. It is preferred that the blocking ring is slightly larger than the cable diameter (optional). 5 Cable Installation 5.1 According to the cable range, chose appropriate gel donut (refer to Table 1) and relevant blocking ring. 5.2 Cable installation Note 1: For install two small cables, snap both 2 dummy rods off, as shown. 3) Cut the ring on the mark (optional). 4
5 4) Install the blocking ring on the gel donut outside facing. 5.7 For two small cables, fit the cable onto the designated cable port and make sure the blocking ring is in the slot, as shown. slot 5.3 Place the blocking ring closed to the gel donut, 1500mm from the cable end. 5.4 Strip the cable and cut the strength member up to 100mm from the cable jacket end. 100mm 1500mm 5.8 Screw tight the upper clamps Note: After slightly tighten the first screw, firmly tighten the second screw. Then, firmly tighten the first screw. Note: If the cable has jacket covered on strength member, Please remove the jacket before installation. 5.5 Use the clean tissue provided to clean the cable sheath, where gel donut will slide though. Note: For single cable, secure the dummy rod With upper clamp, as shown below. 5.6 Insert the strength member underneath the metal washer of the strength member fixture as shown in Step 5.7. Tighten the screw to secure the strength member. Cut the excess off. 5
6 Note: Leave 10mm from the clamp end to the tip end For each cable, as shown below. Note: As Step 5.9, secure cables with tie wraps, as shown. Cut the excess off. 10mm 5.9 Secure cables with tie wraps, as shown. Cut the excess off. 6 Fiber preparation 6.1 Degrease the fiber bundle and slide the transportation tubes over the fibers with overlap 100mm 5.10 For one big cable, fit the cable onto the designated cable port and make sure the blocking ring is in the slot, as shown. Note: Use a Plastic upper clamp. As Step 5.8 to screw tight the upper clamps. 50 mm 150 mm 6.2 Route the transparent tubes to the tray entrance, as shown. # 1,4,5 # 6,2,3 Note: Use a Metal upper clamp. As Step 5.8 to screw tight the upper clamps. # 6 # 5 # 1 # 2 # 4 # 3 6
7 6.3 Secure the transportation tube at the tray entrance with two tie wraps. Note: Maximum two transportation tubes per tray entrance. 7.5 Press-in to release the next tray. 6.4 Coil the loops and store them in the space under the tray supporting bracket, and use tie wraps to tie up the bundle Note: For maintenance convenience, use the plastic pick to scoop out the desired Smouv, as shown. 7 Splicing and fiber storage 7.1 Position the closure close to the splicing machine in a convenient location and secure the closure 7.2 Slide the heat-shrinkable splice protection over one fiber and fuse fibers according to local recommendations and procedures. After the fusion Note: While closure is aerial installed, tray holder is necessary to keep the splice tray in horizontal for maintenance. splice is made, install the heat-shrinkable splice protection (e.g. SMOUV) with an appropriate heating source. Allow the splice protection to cool down to ambient temperature 7.3 After each splice is made, the splice should be stored in the splice holder in the appropriate position, as shown. Do not deform the splice protector during insertion Put the tray holder on the tray bracket when it is not used. 7.4 Put on the tray lid. 7.6 Secure the trays, using Velcro. 7
8 8.2 Use screw to close and open the hanger brackets 7.7 Close the closure by latching the box diagonally Note: Diagonally close the big latches first, and then the small side latches. 8.3 Terminate the hanger brackets onto the steel bar firmly, as shown Steel bar cross section 8 Hanger bracket installation (optional) 8.1 Install the two hanger brackets onto the closure, as shown Note: Maximum torque: 4 Nm Note: For Messenger wire installation, as shown. Messenger wire cross section 9 Re-entry Simply open latches for re-entry. To find out more about CommScope products, visit us on the web at For technical assistance, customer service, or to report any missing/damaged parts, visit us at: CommScope, Inc. All rights reserved. SMOUV, CommScope and all trademarks identified by or are registered trademarks or trademarks, respectively, of CommScope, Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. This product is covered by one ore more U.S. patents or their foreign equivalents. For patents, see:
OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation
OFDC-B8-72 I N S T A L L A T I O N I N S T R U C T I O N Outdoor fiber distribution closure Content 1 Introduction 2 Kit content 3 Closure preparation 4 Cable preparation 4.1 Feeder cable 4.2 Drop cable
FIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.
FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories
2179-CD Series Fiber Optic Splice Closure. Installation Instructions
2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal
FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N
FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N In-line and butt version Cold applied re-usable fiber optic closure Contents 1 Introduction 1.1 Product description 1.2 Capacity 2 General
FOSC-450 Product Range Ordering Guide
of the Gel Sealed Splice Closure (FOSC-450) 1 Product description 2 2 Ordering information 3 2.1 Basic FOSC closures 3 2.2 FOSC closure accessories 4 3 Product guide 5 3.1 Closure description 5 3.2 Closure
2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table
FIST-GCO2-F INSTALLATION INSTRUCTION GCO2-FC GCO2-FD Content 1 Introduction 2 General 2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table 3 Installation
FOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block
FOSC-450D I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories 2.4 Capacity 3 Preparation of the closure 4
Ordering Guide of the Fiber-Optic Splice Closure (FOSC-400)
Page 1 of 11 Ordering Guide of the Fiber-Optic Splice Closure (FOSC-400) This document provides assistance with the selection of FOSC-400 closures. It includes the following sections: 1 Product description
SPECIFICATION FIBER OPTIC SPLICE CLOSURE. Spec No : VSS-1007-BS403A-04A/SD. VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division
SPECIFICATION FIBER OPTIC SPLICE CLOSURE Model Spec. No. Distribution Depts. VSOF-BS403A VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division Sales Division Management Division Revision 10. 07 (Rev.4)
3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays
FIST-MB2-S I N S T A L L A T I O N I N S T R U C T I O N FIST Medium Box for Cable Splicing Only Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and
SJOF-BS604B. Fiber Optic Splice Closure User Manual Rev.1
Fiber Optic Splice Closure 1. Introduction 1.1 General SAMJIN s SJOF-BS604B protects fiber optic splicing point in various installation conditions such as aerial, manholes, ducts, wall and direct buried
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION (FIBER OPTIC SPLICE CLOSURE) Model Spec. No. Distribution Depts. VSOF-BS403A SJP-0609-403A-01A/SD Quality Assurance Team Manufacturing Division Sales Division Management Division
Fiber Optic Splice Closure GPJ Instruction Manual. [Escribir texto]
Fiber Optic Splice Closure GPJ09-8205 Instruction Manual [Escribir texto] 0 Table of Contents 1. General Introduction 2 2. Specification 2 3. Structure 2 4. Installation instructions. 4 5. Operation procedure.
Medium Box for Cable Termination
FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling
SLiC Fiber Aerial Closure System
3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine
2178 Fiber Optic Splice Case and 2181 Cable Addition Kit
2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice
2178-L/S Series Fiber Optic Splice Case with Gasket
2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents
3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes
FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24
Optical Distribution Box 300 Installation Guide. Version : R0.0
Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be
Installation Instructions
TECP-30-260 Issue 2 July 2016 Installation Instructions OWB-S OWB-S Small Wall-mounted Box CONTENTS 1. Introduction 2. Kit content 3. Installation Instruction 3.1. Box installation 3.2. Conduit installation
SPECIFICATION. Spec No : VSS-1402-CS603B
SPECIFICATION Spec No : VSS-1402-CS603B 1. INTRODUCTION 1.1. General This specification covers the design requirements and characteristics required of fiber optic splice closures to be used on fiber optic
Seal Kits for BUDI Enclosures
Description BUDI is a product range of compact, wall mountable fiber enclosures for indoor and outdoor use. They are specifically designed for fast deployment and easy customer connection. The FIST management
Instruction manual. Midi Fiber Dome. Instruction manual
Midi Fiber Dome Instruction manual Product contents: - 1x Midi Fiber Dome - 1x Window Cut port seal - 1x sealing rubber (long) - 4x sealing rubber (short) - 4x stainless steel screw 4 x 25 T20-6x dummies
FOSC 400. Ordering Guide For Closures and Accessories. Section I 3. Section II 5. Section III 9. Section IV 11. Section V 15
FOSC 400 Ordering Guide For Closures and Accessories Section I 3 How to Order FOSC 400 Closures Section II 5 How to Order Accessories for FOSC 400 Closures Section III 9 Other FOSC Fiber Optic Splice Closures
GCO2-BC6/16-XX GCO2-BD6/16-XX GCO2-BE6/16-XX
FIST-GCO2 INSTALLATION INSTRUCTION TC-574-IP Rev A, Feb 2017 www.commscope.com GCO2-BC6/16-XX GCO2-BD6/16-XX GCO2-BE6/16-XX Content 1 Introduction 2 General 2.1 Abbreviation 2.2 Kit Contents 2.3 Elements
24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual
24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number
Fiber Optic Splice Closure GPJ Instruction Manual
Fiber Optic Splice Closure GPJ09-9401 Instruction Manual 1. Brief Introduction GPJ09-9401 type of Fiber Optic Splice Closure is a member in dome series, the main function is to provice direct pass, branch
CONNECTING THE FUTURE 19" LINXS LIGHTWAVE INTEGRATED CROSS-CONNECT SYSTEM USER MANUAL
CONNECTING THE FUTURE 19" LINXS LIGHTWVE INTEGRTED CROSS-CONNECT SYSTEM USER MNUL 109003 Issue Rev 2 19" Lightwave Integrated Cross-Connect System (LINXS) User Manual Document Number 109003 Issue Rev 2
IP-LINX. Installation Guide
Installation Guide Installation Guide, 146653-4 Copyright 2017, Telect, Inc. All Rights Reserved Telect and Connecting the Future are registered trademarks of Telect, Inc. 22425 East Appleway Ave. # 11
FACT Cable Termination Unit
FACT Cable Termination Unit INSTALLATION INSTRUCTION FACT-GSS NOTE: - the FACT-GSS multi-purpose splice shelves features Single Circuit and Single Element fiber management system technology - these shelves
FOSC 400 C5 & D5 Fiber Optic Splice Closures
FOSC 400 C5 & D5 Fiber Optic Splice Closures I N S T A L L A T I O N I N S T R U C T I O N 1. General Product Information The FOSC 400 C5 and D5 closures are combination cable closures and splice organizers,
COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x cm cm x cm)
OCTOBER 2004 COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x 55.88 cm 21.59 cm x 55.88 cm) Be sure to read and completely understand this procedure before applying
IP-LINX Fiber :: X-XXXX
Fiber :: 055-797X-XXXX User Manual Telect, Inc. All rights reserved. 146653-A0 Table of Contents Chapter 1: Introduction...3 1.1 Tools Required...3 1.2 Additional Parts...3 1.3 Assemblies...3 Chapter 2:
3 SLiC Aerial Closure with Rubber End Seal
3 Aerial Closure with Rubber End Seal Instructions 1.0 General 1.1 This instruction bulletin describes the assembly of the 3M Aerial Closure with external bonding hanger brackets. These closures are suitable
Quante BPEO Splice-Protection Closure for Optical Fiber Cables. Features Advantages Benefits
3 Quante BPEO Splice-Protection Closure for Optical Fiber Cables BPEO: Fully Mechanical, Easy to Install, No Specific Tools BPEO is the newest generation of watertight spliceprotection closures for optical
3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR
3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR Instructions July 2010 78-8135-0094-5-K 3 1.0 General 1.1 3M Fiber Optic Splice Closure 2178-XSB The
FOSC 400. Fiber Optic Splice Closure. Features
The FOSC name has been synonymous with excellence in sealing, fiber management, ease of use, and design flexibility since the FOSC 100 closure was first introduced in 1986. FOSC closures have always been
DOME OPTIC SPLICE CLOSURE
FIBER OPTIC SPIICE CLOSURE GJS-JKDH1001-120 BOX DIMENSION: W=140mm H=340mm Weight = 1.80 kgs Outer Internal structure Fuse fiber disc Type sealing ring Plastic hoop base Pole Mount Pole Mount 1 1. product
FIST-GCO2 GCO2-BC8 GCO2-BD8 GCO2-BE8 GCO2-BF8. 5 Heatshrink installation. 1 Introduction. Content. 6 Fiber routing. 2 General. 7 Fiber routing on tray
FIST-GCO2 I N S T A L L A T I O N I N S T R U C T I O N GCO2-BC8 GCO2-BD8 GCO2-BE8 GCO2-BF8 Content 1 Introduction 2 General 2.1 Abbreviation 2.2 Kit Contents 2.3 Elements needed from the FIST installation
FOSC 400 B2/B4. Fiber Optic Splice Closures. Table of Contents. Page 1
FOSC 400 B2/B4 I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closures Table of Contents Page 1. General Product Information 2 2. Warnings 3 3. Required Tools and Materials 3 4. Standard
HCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions September 2017 78-8130-5055-2-M 2 September 2017 78-8130-5055-2-M 1.0 Kit Contents 2.0 General...
RetractaNet XS. Extractable Solutions for OSP. October 2012
RetractaNet XS Extractable Solutions for OSP October 2012 OSP Solutions RetractaNet XS Solution Simple concept reduces the need for skilled labor for installation Easy direct buried deployment in soft
SPECIFICATION FOR FIBER OPTIC SPLICE CLOSURE
SP-CTN-CT3000M,CT3000ML-00 ISSUED : 2015/02/11 PAGE : 8 SPECIFICATION FOR FIBER OPTIC SPLICE CLOSURE CT3000M/CT3000ML Fiber Optic Splice Closure 2 / 8 1. GENERAL This specification covers the standards
INSTALLATION INSTRUCTIONS
LIGHTGUARD 350-20-WTC SEALED FIBER OPTIC CLOSURE VIEW ONLINE TABLE OF CONTENTS: GENERAL...2 SPECIFICATIONS...2 PACKAGE CONTENTS...3 PACKAGE CONTENTS: ACCESSORIES...3 RECOMMENDED TOOLS...3 ADD-ON COMPONENTS...4
FOSC 400. Fiber Optic Splice Closures
FOSC 400 Fiber Optic Splice Closures FOSC 400 - Fiber Optic Splice Closures The FOSC name is synonymous with excellence in sealing, fiber management, ease of use and design flexibility. The original FOSC
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BEFORE INSTALLING OR ADJUSTING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY. PLEASE KEEP THIS GUIDE FOR FUTURE REFERENCE FIBER OPTIC SWING-OUT PATCH PANEL INSTRUCTION
3M Fiber Closures BPEO
3M Fiber Closures BPEO 2 3M Fiber Closures BPEO The 3M Fiber Closures BPEO are designed with flexibility in application in mind. With a range of sizes, they can be deployed above grade (pole, facade) or
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions July 2010 3 1.0 Contents 1.0 General...3 2.0 Kit Contents...3 3.0 Cable Preparation...4 4.0
FOSC 400 A4 Fiber Optic Splice Closure
FOSC 400 A4 Fiber Optic Splice Closure I N S T A L L A T I O N I N S T R U C T I O N 1. General Product Information This installation practice provides instructions for installing Tyco Electronics FOSC
GF-KSW-48 Series of Fiber Optic Distribution Box. Instruction Manual
Instruction manual GF/KSW/48 Page Nr 1 GF-KSW-48 Series of Fiber Optic Distribution Box Instruction Manual 1. General Introduction GF-KSW-48 series of fiber optic distribution box is applicable to fiber
Ordering Guide of the Generic Closure Organizer (FIST-GCO2)
Page 1 of 26 Ordering Guide of the Generic Closure Organizer (FIST-GCO2) This document provides assistance with the selection of FIST Generic Closure Organizers (FIST-GCO2) for use in FIST applications.
Ordering Guide of the Generic Closure Organizer (FIST-GCO2)
Page 1 of 18 Ordering Guide of the Generic Closure Organizer (FIST-GCO2) This document provides assistance with the selection of FIST Generic Closure Organizers (FIST-GCO2) for use in FIST applications.
3A TC 699/SIP/UK/12
Hybrid OTIAN Node I N S T A L L A T I O N I N S T R U C T I O N Generic Joint 3A - Item Code 006825 TC 699/SIP/UK/12 07/15 - Helpline 01793 572453 Contents 1 General description 2 Capacity 3 Kit contents
3M Better Buried Compound Compression Closure System
3M Better Buried Compound Compression Closure System Instructions March 2016 78-0015-2948-2-A Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 Closure Selection Guide...4 4.0 LHS End Cap Installation...5
e-enterable Fiber Optic Splice Closure (Re-Enterable Aerial Closure for Access Service)
R e-enterable Fiber Optic Splice Closure (Re-Enterable Aerial Closure for Access Service) Optical Fiber Drop wire Closure Model FOC-CB1612-24DW. Available with optical fiber cable from 12 up to 24 fibers
27mm ECAM Double Cable Entry Port
27mm ECAM Double Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 27mm ECAM Double Cable (External Cable Assembly Module) Entry Port is designed to accept fiber optic loose tube & central
NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM
NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM Content 1. General 5 2. The products of NC-1000 system 6 3. Mounting of the frame 8 4. Earthing of the frame 8 NC-1000 FIBRE OPTIC
FOSC 400 A4. Fiber Optic Splice Closure. 1. General Product Information I N S T A L L A T I O N I N S T R U C T I O N S
FOSC 400 A4 I N S T A L L A T I O N I N S T R U C T I O N S Fiber Optic Splice Closure Table of C ontents P age 1. General Product Information.............................................................1
18mm ECAM Cable Entry Port
18mm ECAM Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 18mm ECAM (External Cable Assembly Module) Cable Entry Port Kit is designed to accept fiber optic cables with external diameters
Customer-Owned Outside Plant
Customer Premises Products (Enterprise) 3 Customer-Owned Outside Plant Fiber Optic Splice Case 2178 Series and Accessories 372 Fiber Optic Dome Splice Closure FD Series 376 Fibrlok II Universal Optical
Ordering Guide. for FIST-GCO2 product range
Ordering Guide for FIST-GCO2 product range Page 1 of 18 Ordering Guide of the Generic Closure Organizer (FIST-GCO2) This document provides assistance with the selection of FIST Generic Closure Organizers
MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures. 1. General. 2. Precautions
MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures 004-273-AEN, Issue 2 Table of Contents 1. General.... 1 2. Precautions.... 1 2.1 Cable Handling Precautions...
3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket
3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket For use with 3M SLiC Free-Breathing Fiber Optic Closures and Terminals Instructions November
3 Foam Sealed Closure 2" (50 mm) with Compound Compression
3 Foam Sealed Closure 2" (50 mm) with Compound Compression Instructions 1.0 General 1.1 The 3M Foam Sealed Closure is designed to be used in the construction and maintenance of buried and underground PIC
3M Fiber Optic Splice Closure 2178-L/S Series with Gasket
3M Fiber Optic Splice Closure 2178-L/S Series with Gasket Instructions for: 3M Fiber Optic Splice Closures 2178-L/S Series 3M Flame Retardant Fiber Optic Splice Closures 2178-L/S/FR 3M Cable Addition Kit
2178 L/S Series Fiber Optic Splice Cases and Accessories
2178 L/S Series Fiber Optic Splice Cases and Accessories The 3M 2178 Fiber Optic Splice Case family has always given you great protection for fiber optic connections. Now, the addition of 3M 2178-L/S Series
LANmark-OF ENSPACE Patch Panel
LANmark-OF ENSPACE Patch Panel PRODUCT INSTALLATION GUIDE September 2016 v0.11 LANmark-OF ENSPACE Patch Panel PRODUCT INSTALLATION GUIDE Part Number Description Product References NSPACE.PP1U NSPACE.PP2U
3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter
3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter Instructions January 2010 3 1.0 General 1.1 The 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter(s) protects, organizes and stores
3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882)
3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462FN and 3M High Gel Reenterable Encapsulant 8882) Instructions April 2016 78813509979C Contents: 1.0 General... 1 2.0 Kit Contents...
Flexible Fiber Management Solutions
Communication Markets Division 3M Fiber Optic Splice Closure 2178 Family Flexible Fiber Management Solutions More flexibility for your complex fiber optic network A full line of closures and accessories
Public Works Division Lighting District Fiber Optic Specifications April 2009
Public Works Division Lighting District Fiber Optic Specifications April 2009 7000 Florida Street Punta Gorda, Florida 33950 Tele: 941.575.3600 Fax : 941.637.9265 www.charlottecountyfl.com/publicworks
The FiberMark1 offers an ideal solution for
Large Capacity Fiber Optic Splice Enclosure The Ideal Solution For Large Capacity Voice, Data, and Video Splicing Requirements. The FiberMark1 offers an ideal solution for larger fiber capacity voice,
GCO2-BC6/16-MC-XV GCO2-BD6/16-MC-XV GCO2-BE6/16-MC-XV. 3.1 Installation of the workstand 3.2 Opening the FIST-GCO2
FIST-GCO2-BX6/16-MC I N S T A L L A T I O N I N S T R U C T I O N GCO2-BC6/16-MC-XV GCO2-BD6/16-MC-XV GCO2-BE6/16-MC-XV Content 1 Introduction 2 General 2.1 Abbreviation 2.2 Kit Contents 2.3 Accessories
Ordering Guide. for FIST-GSS2 product range
Ordering Guide for FIST-GSS2 product range Page 1 of 17 Ordering Guide of the Generic Splicing Shelf (FIST-GSS2) This document provides assistance with the selection of shelves for use in FIST cable termination
INSTALLATION GUIDE. LANmark-OF Zone Distribution Box
LANmark-OF Zone Distribution Box INSTALLATION GUIDE LANmark-OF Zone Distribution Box Document information Release November 2004 Published by Contact address Nexans Cabling Solutions Alsembergsesteenweg
Introduction to Fiber Optic Cable Technology Jerry Bednarczyk, PE Course Content
Introduction to Fiber Optic Cable Technology Jerry Bednarczyk, PE Course Content Page 1 of 10 GENERAL A fiber optic cable system is very similar to a copper wire system in that it is used to transmit data
3M Fiber Optic Wall Mount Enclosure 8430 Series
3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6
Mid-Span Access of Loose-Tube Ribbon Fiber Optic Cable
Application Notes Mid-Span Access of Loose-Tube Ribbon Fiber Optic Cable Author Prasanna Pardeshi and Sudipta Bhaumik Issued November 2013 Abstract In fiber optic network, it is sometime necessary to splice
3M Fiber Optic Closure System LL
3M Fiber Optic Closure System LL 3M Fiber Optic Closure System The 3M Fiber Optic Closure System LL provides a protective yet accessible environment for housing single or mass fusion fiber splices. The
WCH Slack Storage Housing (WCH-SSH-2 & WCH-SSH-4-12)
Corning Cable Systems SRP-003-448 Issue 3, October 2000 Page 1 of 6 WCH Slack Storage Housing (WCH-SSH-2 & WCH-SSH-4-12) Figure 1 Table of Contents 1. General... 1 2. Description... 1 3. Tools and Materials...
3M Better Buried Closures
3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...
Instructions. Cable with Armor F CAUTION. October Rev A
3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables
3M Fiber Optic Splice Closure 2178 Family. Flexible Fiber. Management Solutions
3M Fiber Optic Splice Closure 2178 Family Flexible Fiber Management Solutions More flexibility for your complex fiber optic network A full line of closures and accessories designed to protect fiber optic
Fiber Optic Closure. Fiber Optic Splice Closure For Aerial Line. Model : W-ICL-007-xxF. Features
Fiber Optic Splice Closure For Aerial Line Model : W-ICL-001-xxF Model : W-ICL-002-xxF Model : W-ICL-003-xxF Model : W-ICL-004-xxF Model : W-ICL-005-xxF Model : W-ICL-006-xxF Model : W-ICL-007-xxF Features
Installing a Wire Mesh Pulling Grip on All-Dielectric DX Armored Fiber Optic Cables
revision history Issue Date Reason for Change Related literature SRP-004-136 Accessing All-Dielectric DX Armored Fiber Optic Cables Admonishments 1. General This procedure provides instructions for installing
3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series
3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series Instructions Voltage Rating: 1000 V, Temperature Rating: 90 C Kit Contents 78-R1 78-R2 78-R3 78-R4 78-R5 Sleeve Set 1 1 1 1
Water blocking tape. Locator ridge HPA-0486
Table of Contents STANDARD RECOMMENDED PROCEDURE 004-138 ISSUE 1 MARCH 2012 PAGE 1 OF 12 Sheath Removal and Mid-Span Access of Dielectric ALTOS Cable with FastAccess Technology p/n 004-138, Issue 1 1.
FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N
FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N 24 Address Point Fibre distribution point (FDP) Installation guide for fibre DP Contents 1 Kit Contents 2 Accessories 3 MOBRA installation
High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions
High Density Block BRCP HD BRCP- 128/192/256 pair Installation Instructions Product Introduction The BRCP block is the latest generation of MDF terminal blocks developed by 3M, specifically designed for
LEGEND POWER SYSTEMS
S HEAT SHRINK JOINT 11kV 3 CORE Armoured XLPE/EPR Copper Wire screens STRAIGHT JOINT LEGEND POWER SYSTEMS Date 11 November 2014 Instruction Number PJJ006-14C PJJ006-14C Page 1 of 10 HEAT SHRINKABLE JOINT
SPECIAL SPECIFICATION 6559 Telecommunication Cable
2004 Specifications CSJ 0015-09-147, etc. SPECIAL SPECIFICATION 6559 Telecommunication Cable 1. Description. This specification governs the materials, installation, termination, splicing, testing, training,
GENUINE PARTS CAUTION
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: SATELLITE RADIO SYSTEM 2. PART NUMBERS: XM tuner kit 999U9-NV003 XM antenna kit 999U9-VR000 Sirius tuner kit 999U9-NV004 Sirius antenna
ALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, Fibers
ALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, 12-72 Fibers P/N 004-223-AEN Issue 1 1. General This procedure describes cable-end and mid-span sheath removal and fiber access of ALTOS
3M Coupling Tray FDTC-10S-COUPLINGTRAY
3M Coupling Tray FDTC-10S-COUPLINGTRAY for use with 3M Fiber Dome Closures FDC 10S Instructions July 2010 3 1.0 Introduction The 3M Coupling Tray FDTC-10S-COUPLINGTRAY can accommodate up to 10 loose tubes.
Splice Closure Fiber (SCF) Family
features and benefits Sealed butt-style closure Aerial, wall, pole, direct buried Ribbon reel-end to reel-end splicing Split end caps Modular fiber management system standards Telcordia GR-771 tested RDUP
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS. 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~)
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~) Xterra (2006~) 3. PART NUMBERS: XM Tuner Kit 999U9-AS003 SIRIUS Tuner Kit
Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier.
Communication Markets Division 3M Fiber Closures Smart design makes your job easier. 2 Your connections deserve the best protection. No matter the size and configuration of your network, protecting its