DA-12R. User Manual. 1 to 2 RGBHV Distribution Amplifier. rev (English) COMM-TEC GmbH Siemensstr. 14 D Uhingen

Transcription

1 1 to 2 RGBHV Distribution Amplifier User Manual rev (English) COMM-TEC GmbH Siemensstr. 14 D Uhingen Tel.: Fax: Copyright by COMM-TEC

2 INDEX 1.0 Overview 2.0 Power 3.0 Settings 4.0 Installation 5.0 Accessories 6.0 Technical data 7.0 Notes You are kindly requested to read the present manual before installing the. Manufacturer does not assume any liability for damages due to the use, even correct, of its products. Data and specifications may change without notice.

3 1.0 OVERVIEW Thanks for purchasing this product. Please check the contents of the packing. It contains: - The unit - The present user manual - The Power Supply is a 1 x 2 high resolution RGBHV distribution amplifier. It's compatible with many standards as: - Composite (triple 1x2 CVBS distributor) - Component YUV - Computer RGBHV - RGBS (Composite sync. SUN, SGI) - RGsB (Sync On Green) unit receives signals from the source by 5 BNC. The two BNC outputs can be buffered to reach the distance up to 100 m without losses.

4 2.0 POWER is powered only by the AC adapter equipped with the unit. Units don't have adjustment or setting inside. Servicing must be made by qualified personnel. The adapter must be fitted in a Vac/50 Hz socket. 3.0 SETTINGS The ensure compatibility of with the whole of sources either broadcast or informatics, input impedance of H (Comp.) automatically conforms to the source. If the source gives a TV negative sync, it will be terminated at 75 Ohm. In the other cases the input will remain in high impedance. By a dip-switch accessible from the bottom of the unit the output can be buffered. 1 BOOST :In On pos. the BNC outputs are buffered. For length equal or greater than 50 m. The switch BOOST must be set in ON pos. The unit is factory-set as follows: 1 BOOST :OFF

5 4.0 INSTALLATION a) Be sure that all units to be installed are in OFF state. b) Connect the source to INPUT RGBHV by a RG59 B/U cable. ATTENTION If your source gives signals RGB+S connect the S to the BNC H. If your source gives the Sync On Green leave open the BNC H are V. If your source has an HDD 15 p.f. as output connector, use a COMM-TEC adapter cable as an interface. c) Connect the two destination with BNC RGBHV output by a RG59 B/U cable. d) Power the unit as described in chapter 2.0 and check that the led POWER on front panel lights up. ATTENTION does not process the sync. So the destinations must be compatible with the source. If they aren't it's necessary to interpose an interface type COMM-TEC IF-11V or IF-12VA ATTENTION The length of cables which bring RGB signals must be the same with a tolerance of 0,5 m. Greater difference may cause a significative loss of the image resolution.

6 5.0 ACCESSORIES The following items are included with the unit: - Power Adapter The following items are available on request: - RMK-2HE: 19" Rack Mount Kit for 2 units, 2 RU - RMK-2HE-BLK: Blank Panel for RMK-2HE 6.0 TECHNICAL DATA Name Function : :high resolution signals distributor RGB signals :analogue Input impedance 75 Ohm Coupling :DC Crosstalk (worst case) :>30 db at 40 MHz Diff. amplitude :0.1% Diff. phase :0.1 H Sync. (Comp.) Input impedance Output impedance V Sync. Input/output connectors Bandwidth Driving capability Power consumption Size (W x D x H) :Horizontal TTL pos/neg, Composite TTL, TV negative level 0,3 to 2 VPP onto 75 ohm :automatic, high Z for TTL, 75 ohm for TV neg. level :fixed 75 Ohm :TTL pos./neg. :BNC :250 MHz :>100 m with RG59 B/U cable (BOOST ON) :5 VA :220 x 100 x 55 mm According to EN for immunity and emission.

7 7.0 NOTES This product is guaranteed for two years from date of purchase. Warranty falls off if defect is due to negligence in use or intervention of unauthorised personnel. In the course of warranty COMM-TEC will repair the faulty units for free. Faulty units must arrive to COMM-TEC free of charge and with return transportation pre-paid. Out of warranty COMM-TEC will repair faulty units with cost charged to customer. Units must arrive to COMM-TEC free of charge and with return transportation prepaid. For any need during installation of or any other information call the COMM-TEC hotline or