Instruction manual. Midi Fiber Dome. Instruction manual

Size: px

Start display at page:

Download "Instruction manual. Midi Fiber Dome. Instruction manual"

Olivia Morris
3 years ago
Views:

- 1x tube silicone grease Required tools Torx T20 screwdriver Clamp Measuring tape, permanent marker, cable

1 Midi Fiber Dome Instruction manual Product contents: - 1x Midi Fiber Dome - 1x Window Cut port seal - 1x sealing rubber (long) - 4x sealing rubber (short) - 4x stainless steel screw 4 x 25 T20-6x dummies (to seal unused ports) - 1x tube silicone grease Required tools Torx T20 screwdriver Clamp Measuring tape, permanent marker, cable knife, side-cutting pliers and Kevlar scissors. Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 1 van 7

the sealing rubber at this markation point Shorten the strength element at 4 cm from where the cable was opened Attention: in

2 Mounting a Midi Fiber Dome 1. Secure the MFD by using a vise or a clamp Prepare the cables and/or ducts with the correct length (take the prescribed overlength into account) 2. Make a window cut in the feeder cable Mark the feeder cable at 4cm from the end where the cable was opened Place a short peace of the sealing rubber at this markation point Shorten the strength element at 4 cm from where the cable was opened Attention: in case a window cut is not necessary, carry out step 2 for the single feeder cable 3. Enter the window cut in the Midi Fiber Dome and directly fixate the strength element(s) under the cover plates Use a T20 screwdriver to tighten the strength elements under the metal plates Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 2 van 7

4. Break out the port(s) where a cable has been inserted 5.

cable until the triangles are aligned 6.

screwdriver for tightening the 3 screws Attention: Hold the inner

3 4. Break out the port(s) where a cable has been inserted 5. Place the inner part of the Window Cut port seal over the feeder cable until the triangles are aligned 6. Roll the long piece of sealing rubber into the shape of a sausage and divide it equally into the port. 7. Fixate the outer part of the Window Cut port seal Again use a T20 screwdriver for tightening the 3 screws Attention: Hold the inner part of the Window Cut port seal when tightening the 3 screws Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 3 van 7

. 8. If a black edge of rubber is visible around the Window Cut port seal, the seal is made

Port seal must be unscrewed, re-divide rubber (step 6) and step 7 must be redone until

Place the overlength of the tubes / fibers that are not being used under the velcro 10.

4 . 8. If a black edge of rubber is visible around the Window Cut port seal, the seal is made correctly. If the black edge of rubber is not visible, the rubber is not well divided. Port seal must be unscrewed, re-divide rubber (step 6) and step 7 must be redone until rubber edge is visible 9. Place the overlength of the tubes / fibers that are not being used under the velcro 10. Bring the tubes / fibers that need to be spliced to the other side where the cassettes are placed Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 4 van 7

11. Strip the tubes from the markation point as shown in the picture 12.

There must not be any lengthways cuts past the end.

Rub a thin layer of the silicone grease provided on the outer end of the

5 11. Strip the tubes from the markation point as shown in the picture 12. The tube(s) can optionally be extra fixated with a tie-wrap Attention: do not tighten tie-wrap too tightly 13. Cut the outer sleeve of the cable / duct perpendicularly. There must not be any lengthways cuts past the end. Use alcohol to remove any grease from the first 4 cm of the cable / duct Rub a thin layer of the silicone grease provided on the outer end of the duct / cable 14. Insert the customer cables and / or ducts until the end stop (see red arrow) Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 5 van 7

In case of DB microduct entry: Provide gas seal between fiber and duct.

and extra space has been created for a gas seal 15.

tubes are not stripped halfway the tube guide due to the possibility of kinking the tubes Splice the

Place the Fibers in the splice tray according to the splice diagram. 16.

6 In case of DB microduct entry: Provide gas seal between fiber and duct. The transparent end stop can be turned around so that the end stop is slightly further (see black arrow) and extra space has been created for a gas seal 15. Strip the tubes at the end of the tube guide (or before the tube guides) Attention: it is important that tubes are not stripped halfway the tube guide due to the possibility of kinking the tubes Splice the Fibers according to the instructions. Place the Fibers in the splice tray according to the splice diagram. 16. Feed the Velcro through the top cassette, and then return it and press it 17. Place dummies in the customer ports without a cable / duct Rub a thin layer of the silicone grease provided on the insert length of the dummy. Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 6 van 7

By placing the top of the dome on, for example, a workbench you can more easily press them

7 18. Place the dome on the bottom Attention: it is important that the dome is completely connected to the bottom. By placing the top of the dome on, for example, a workbench you can more easily press them together 19. Place the red closing ring over the dome and turn it until it is completely locked End instruction manual Instruction manual V1.0 _ _ Midi Fiber Dome _ Pagina 7 van 7

OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation

OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation OFDC-B8-72 I N S T A L L A T I O N I N S T R U C T I O N Outdoor fiber distribution closure Content 1 Introduction 2 Kit content 3 Closure preparation 4 Cable preparation 4.1 Feeder cable 4.2 Drop cable