TITLE : HV070WSA-100 Product Specification Rev.O

Transcription

1 PROPRIETARY NOTE THI PECIFICATION I THE PROPERTY OF BOE OT AND HALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMIION OF BOE OT AND MUT BE RETURNED TO BOE OT UPON IT REQUET TITLE : HV7WA- Product pecification Rev.O BEIJING BOE OPTOELECTRONIC TECHNOLOGY PEC. NUMBER PRODUCT GROUP TFT-LCD REV. O IUE DATE OF 28 B26-56-O (/3) A4(2 X 297)

2 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O REVIION HITORY REV. ECN NO. DECRIPTION OF CHANGE DATE PREPARED O - Initial Release DongXue PEC. NUMBER PEC TITLE HV7WA- Product pecification 2 OF 28 B26-56-O (2/3) A4(2 X 297)

3 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Contents No. Items Page. General Description 4 2. Absolute Maximum ratings 6 3. Electrical specifications Optical specifications Interface Connection 3 6. ignal Timing pecification 6 7. ignal Timing waveforms 8 8. Input ignals, Display Colors & Gray cale of Colors 9 9. Power equence 2. Connector description 2. Mechanical Characteristics Reliability Test Handling & Cautions Label Packing information Mechanical Outline Dimension 27 PEC. NUMBER PEC TITLE HV7WA- Product pecification 3 OF 28 B26-56-O (3/3) A4(2 X 297)

4 GENERAL DECRIPTION. Introduction PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O HV7WA- is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 7. inch diagonally measured active area with WVGA resolutions (24 horizontal by 6 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 6.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. LVD Input ignal CTFT LCD Panel 24 6 Connector (CN ) VDD DC/DC Gamma Vcom ource Driver Gat te Driver V_LED LED Driver FPC Back Light (MD LED Array).2 Features Channel LVD Interface with pixel / clock Thin and light weight Display 6.7M colors (Hi FRC) High luminance and contrast ratio, low reflection and wide viewing angle DE (Data Enable) signal mode 3.7V for Logic Power and LED Back Light Power RoH Compliant & Halogen free PEC. NUMBER PEC TITLE HV7WA- Product pecification 4 OF 28 B26-56-O (3/3) A4(2 X 297)

5 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Application Tablet & Application Mini-PC (Wide Type).4 General pecification < Table. General pecifications > Parameter pecification Unit Remarks Active area 53.6(H) 9(V) mm Number of pixels 24(H) 6(V) pixels Pixel pitch 5(H) 5(V) RGB μm Pixel arrangement Pixels RGB stripe arrangement Display colors 6.7M(6bits + H-FRC) colors Display mode Transmission mode, Normally Black Outline Dimension 64.5(H).86(V) 2.35(D) typ. mm Weight 9 (max) gram urface Treatment Hard Coating, 3H, Low Reflection (Front Polarizer) Back-light Bottom edge side, -LED Lighting Bar 2* LED Array Type PEC. NUMBER PEC TITLE HV7WA- Product pecification 5 OF 28 B26-56-O (3/3) A4(2 X 297)

6 2. ABOLUTE MAXIMUM RATING PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. LCD Module Electrical pecifications > [Ta =25±2 ] Parameter ymbol Min. Max. Unit Remarks Power upply Voltage (LCD Module) V DD V Back-light Power upply Voltage HV DD V Back-light LED Current I LED - 3 ma Back-light LED Reverse Voltage V R - 2 V Operating Temperature T OP torage Temperature T T ) Note : ) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 max. and no condensation of water. Relative Humudity 9 (4, 9) 8 6 Operating Range (5, 5) 4 (65, 27) 2 5 torage Range (85, 2) Temperature ( ) PEC. NUMBER PEC TITLE HV7WA- Product pecification 6 OF 28 B26-56-O (3/3) A4(2 X 297)

7 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O ELECTRICAL PECIFICATION 3. TFT LCD Module < Table 3. LCD Module Electrical pecifications > [Ta =25±2 ] Parameter ymbol Values Min Typ Max Power upply Input Voltage V DD V Unit Power upply Current I DD ma Back-light Power upply Voltage Back-light Power upply Current H VDD V I HVDD ma LED Driver Efficiency η % Positive-going Input Threshold Voltage Negative-going Input Threshold Voltage Differential input common mode voltage V IT mv V IT mv Notes Note Note 2 Vcom =.2V typ. V V com V IH =mv, mode voltage V IL =-mv Power Consumption P D -.78 W Note P BL.25 W Note 2 P Total 2. W Notes :. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.7V at 25 a) Typ : Black Pattern 2. Calculated value for reference (VLED X ILED) PEC. NUMBER PEC TITLE HV7WA- Product pecification 7 OF 28 B26-56-O (3/3) A4(2 X 297)

8 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Back-light Unit < Table 4. LED Driving guideline specifications > Ta=25+/-2 C Parameter Min. Typ. Max. Unit Remarks LED Forward Voltage V F V - LED Forward Current I F ma - LED Power Consumption P LED W Note LED Life-Time N/A 5, Hour Power supply voltage for LED Driver V LED V IF = 2mA Note 2 EN Control Level Backlight on mv Backlight off mv PWM Control Level PWM High Level PWM Low Level V -.6 V PWM Control Frequency F PWM 5 - KHz Duty Ratio - 9% 93% - % Notes :. Calculator Value for reference I LED V LED = P LED 2. The LED Life-time define as the estimated time to 5% degradation of initial luminous. PEC. NUMBER PEC TITLE HV7WA- Product pecification 8 OF 28 B26-56-O (3/3) A4(2 X 297)

9 4. OPTICAL PECIFICATION 4. Overview PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O The test of Optical specifications shall be measured in a dark room (ambient luminance lux and temperature = 25±2 ) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5) and test unit shall be located at an approximate distance 5cm from the LCD surface at a viewing angle of θ and Φ equal to. Werefer to θø= (=θ3 ) as the 3 o clock direction (the right ), θø=9 (= θ2 ) as the 2 o clock direction ( upward ), θø=8 (= θ9 ) as the 9 o clock oclock direction ( left ) (left)and θø=27(= θ6 ) as the 6 o clock direction ( bottom ). While scanning θand/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 3 minutes prior to measurement. VDD shall be 3.7 ±.5V at 25 C. Optimum viewing angle direction is 6 clock. 9 Points Y w 4.2 Optical pecifications <Table 5. Optical pecifications> Parameter ymbol Condition Min. Typ. Max. Unit Remark Θ Horizontal Deg. Viewing Angle Θ Deg. CR > range Θ Vertical Deg. Θ Deg. Note Color Temperature K Color Gamut % Luminance Contrast t ratio CR Θ = 7 9 Note 2 Luminance of White cd/m 2 Note 3 White Θ = Luminance uniformity 9 Points ΔY Note 4 White Chromaticity W x Typ..33 Typ. Θ = W y Note 5 Red R x.6 R y.34 Reproduction Green Θ = of color y G x G Typ Typ. Blue B x.45 B y.25 Response Time Ta= 25 C T (Rising + Falling) RT Θ = ms Note 6 Cross Talk CT Θ = % Note 7 PEC. NUMBER PEC TITLE HV7WA- Product pecification 9 OF 28 B26-56-O (3/3) A4(2 X 297)

10 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Notes :. Viewing angle is the angle at which the contrast ratio is greater than. The viewing angles are determined for the horizontal or 3, 9 o clock direction and the vertical or 6, 2 o clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE ). 2. Contrast measurements shall be made at viewing angle of Θ= and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (see FIGURE ) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster 3. Center Luminance of white is defined as luminance values of 9 point average across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. the LED current is setting at 2mA. 4. The White luminance uniformity on LCD surface is then expressed as : ΔY = Minimum Luminance of 9 points / Maximum Luminance of 9 points (see FIGURE 2). 5. The color chromaticity coordinates specified in Table 5 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. The electro-optical response time measurements shall be made as FIGURE 3 by switching the data input signal ON and OFF. The times needed for the luminance to change from % to 9% is Tr, and 9% to % is Td. 7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (ee FIGURE 4). PEC. NUMBER PEC TITLE HV7WA- Product pecification OF 28 B26-56-O (3/3) A4(2 X 297)

11 4.3 Optical measurements PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Figure. Measurement et Up Photo detector (TOPCON BM-5A) TFT-LCD module Field = o 5 cm LCD panel Center of the screen Optical characteristics measurement setup Figure 2. White Luminance and Uniformity Measurement Locations (9 points) Center Luminance of white is defined as luminance values of center 9 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. The White luminance uniformity on LCD surface is then expressed as : ΔY9 = Minimum Luminance of five points / Maximum Luminance of nine points (see FIGURE 2). PEC. NUMBER PEC TITLE HV7WA- Product pecification OF 28 B26-56-O (3/3) A4(2 X 297)

12 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Figure 3. Response Time Testing Display data Black (TFT OFF) White (TFT ON) Black (TFT OFF) Optical Response % 9% TR TF % % Time The electro-optical response time measurements shall be made as shown in FIGURE 3 by switching the data input signal ON and OFF. The times needed for the luminance to change from % to 9% is Tr and 9% to % is Td. Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA 256,5 768,5 L3 Y B (768, 3) 256,45 768,45 Y A (768,3) L Where: Y B -Y A Cross-Talk (%) = Y A = Initial luminance of measured area (cd/m 2 ) Y 2 B = ubsequent luminance of measured area (cd/m ) Y A The location measured will be exactly the same in both patterns Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark (Refer to FIGURE 4). PEC. NUMBER PEC TITLE HV7WA- Product pecification 2 OF 28 B26-56-O (3/3) A4(2 X 297)

13 5. INTERFACE CONNECTION. PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O El 5. Electrical ti linterface Connection The electronics interface connector is FF2-3A-RB. The connector interface pin assignments are listed in Table 6. <Table 6. Pin Assignments for the Interface Connector> Terminal ymbol Functions Pin No. ymbol Description VDDIN 2 VDDIN 3 VDDIN 4 VDDIN Power supply VDDIN=3.7V (Typ.) 5 VDDIN 6 VDDIN 7 VDDIN 8 NC Non Connection 9 NC Non Connection LDO_EN LDO enable for driver IC GND GROUND 2 GND GROUND 3 RIN- LVD Negative data signal (-) 4 RIN+ LVD Positive data signal (+) 5 GND GROUND 6 RIN- LVD Negative data signal (-) 7 RIN+ LVD Positive data signal (+) 8 GND GROUND 9 RIN2- LVD Negative data signal (-) 2 RIN2+ LVD Positive data signal (+) 2 GND GROUND 22 LVD_CLK- LVD Negative CLK signal (-) 23 LVD_CLK+ LVD Positive CLK signal (+) 24 GND GROUND 25 RIN3- LVD Negative data signal (-) 26 RIN3+ LVD Positive data signal (+) 27 GND GROUND 28 LED_EN LED enable 29 GND GROUND 3 DVDD 3.3V Power 3 GND GROUND PEC. NUMBER PEC TITLE HV7WA- Product pecification 3 OF 28 B26-56-O (3/3) A4(2 X 297)

14 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O LVD Interface PC ide TFT-LCD ide R~R7 G~G7 B~B7 Hsync Vsync DE TTL Parallel-to o-lvd CN ohm ohm ohm ohm LVD to TTL Parallel R ~ R5 G ~ G5 B ~ B5 Hsync Vsync DE CLK PLL ohm PLL CLK 5.3.LVD Input signal PEC. NUMBER PEC TITLE HV7WA- Product pecification 4 OF 28 B26-56-O (3/3) A4(2 X 297)

15 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Data Input Format (,) (2,) (23,) (24,) R G B R G B R G B R G B Pi Pixel = 3D Dots R G B R G B R G B R G B R G B (,6) (2,6) (23,6) (24, 6) Display Position of Input Data (V-H) PEC. NUMBER PEC TITLE HV7WA- Product pecification 5 OF 28 B26-56-O (3/3) A4(2 X 297)

16 6. IGNAL TIMING PECIFICATION PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O The HV7WA- is operated by the DE only. Item ymbols Min Typ Max Unit Frequency /Tc MHz Clock High Time Tch 4% 5% 6% Tc Low Time Tcl 6% 5% 4% Tc lines Frame Period Tv Hz ms Vertical Display Period Tvd lines One line canning Period Horizontal Display Period Th clocks Thd clocks PEC. NUMBER PEC TITLE HV7WA- Product pecification 6 OF 28 B26-56-O (3/3) A4(2 X 297)

17 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O LVD Rx Interface Timing Parameter The specification of the LVD Rx interface timing parameter is shown in Table 8. <Table 8. LVD Rx Interface Timing pecification> Item ymbol Min Typ Max Unit Remark CLKIN Period trcip nsec Input Data trip nsec Input Data trip tricp/7-.4 tricp/7 tricp/7+.4 nsec Input Data 2 trip7 2 tricp/ tricp/7 2 tricp/7+.4 nsec Input Data 3 trip6 3 tricp/ tricp/7 3 tricp/7+.4 nsec Input Data 4 trip5 4 tricp/ tricp/7 4 tricp/7+.4 nsec Input Data 5 trip4 5 tricp/ tricp/7 5 tricp/7+.4 nsec Input Data 6 trip3 6 tricp/ tricp/7 6 tricp/7+.4 nsec Input Data 7 trip2 7 tricp/ tricp/7 7 tricp/7+.4 nsec trip trip6 trip7 trip5 trip trip2 trip3 trip4 RXO/Ez +/- * Z =,, 2,3 Rx2 Rx Rx Rx7 Rx6 Rx5 Rx4 Rx3 Rx2 Rx Rx RxOCLKIN+ Vdiff=[v] trcip Vdiff=[v] RxECLKIN+ * Vdiff = (RXO/Ez+)-(RXO/Ez-),.,(RXO/ECLK+)-(RXO/ECLK-) PEC. NUMBER PEC TITLE HV7WA- Product pecification 7 OF 28 B26-56-O (3/3) A4(2 X 297)

18 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O IGNAL TIMING WAVEFORM OF INTERFACE IGNAL DCLK tclk.5 VDD Valid data First data Invalid data Pixel data Pixel data Invalid data Valid data econd data Invalid data Pixel data Pixel data Invalid data DE(Data Enable) Hync thp thv DE(Data Enable) tvp Vync tvv DE(Data Enable) PEC. NUMBER PEC TITLE HV7WA- Product pecification 8 OF 28 B26-56-O (3/3) A4(2 X 297)

19 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O INPUT IGNAL, BAIC DIPLAY COLOR & GRAY CALE OF COLOR, Cyan Green Blue Black B6 B5 B4 B3 B2 B B G5 G4 G3 G2 G G G6 R3 R4 R5 R6 R R2 R B7 G7 R7 Blue Data Green Data Red Data Color & Gray cale Input Data ignal White Yellow Magenta Red Cyan Basic Colors Darker Black Gray cale Darker Black Gray cale of Green Red Brighter of Red Green Brighter Darker Black Gray cale of Blue Blue Brighter Darker Brighter Black Gray cale of White B26-56-O (3/3) A4(2 X 297) PEC. NUMBER PEC TITLE HV7WA- Product pecification OF Brighter White

20 9. POWER EQUENCE PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below Parameter Values Min Typ Max Units T.5 - ms T2-5 ms T ms T ms T5.5-5 ms T6 - ms T ms Notes:. When the power supply VDD is V, keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. Back Light must be turn on after power for logic and interface signal are valid. PEC. NUMBER PEC TITLE HV7WA- Product pecification 2 OF 28 B26-56-O (3/3) A4(2 X 297)

21 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Connector Description Physical interface is described as for the connector on LCM. These connectors are capable of accommodating the following signals and will be following components.. TFT LCD Module Connector Name /Description For ignal lconnector Manufacturer Type/ Part Number DDK or Compatible FF2-3A-RB or Compatible.2 LED Connector Pin No. ymbol For ignal Connector VLEDP LED Anode Power upply 2 VLEDN 3 VLEDN2 4 VLEDN3 LED Cathode Power upply 5 VLEDN4 PEC. NUMBER PEC TITLE HV7WA- Product pecification 2 OF 28 B26-56-O (3/3) A4(2 X 297)

22 MECHANICAL CHARACTERITIC. Dimensional Requirements PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O FIGURE 5 shows mechanical outlines for the model HV7WA-. Other parameters are shown in Table 9. <Table 9. Dimensional Parameters> Parameter pecification Unit Active Area 53.6 (H) 9 (V) Number of pixels 24(H) X6 (V) ( pixel = R + G + B dots) Pixel pitch.5 (H) X.5 (V) Pixel arrangement RGB Vertical stripe Display colors 6.7M Display mode Normally Black Dimensional outline 64.5*.86*2.35 (Typ.) mm Weight 9 (Max) gram Back-light LED, Horizontal-LED Array type.2 Mounting ee FIGURE 6..3 Glare and Polarizer Hardness. The surface of the LCD has an low reflection coating and hard coating to reduce scratching..4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 5cm from the screen with an overhead light level of 5lux. PEC. NUMBER PEC TITLE HV7WA- Product pecification 22 OF 28 B26-56-O (3/3) A4(2 X 297)

23 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O RELIABILITY TET The Reliability test items and its conditions are shown in below. <Table. Reliability test> No Test Items Conditions High temperature storage test Ta = 85, 24 hrs 2 Low temperature storage test Ta = -4, 24 hrs 3 High temperature & high humidity operation test Ta = 6, 9%RH, 96 hrs 4 High temperature operation test Ta = 6, 24 hrs 5 Low temperature operation test Ta = -2, 24 hrs 6 Thermal shock Ta = (2 hr), 3 cycle 3. HANDLING & CAUTION () Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions for the operation When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. PEC. NUMBER PEC TITLE HV7WA- Product pecification 23 OF 28 B26-56-O (3/3) A4(2 X 297)

24 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O (4) Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high h temperature t and/or humidity atmosphere. torage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. (6) Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. 4. LABEL () Product label HV7WA X X X X X X X X X X X X X X Type designation No. Control Number No 2. Rank / Grade No 3. Line classification (BOE OT:A/BC) No 4. Year (9 : 29, : 2, ) No 5. Month (, 2, 3,, 9, X, Y, Z) No 6. Product Identification (FG) No 7. erial Number PEC. NUMBER PEC TITLE HV7WA- Product pecification 24 OF 28 B26-56-O (3/3) A4(2 X 297)

25 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O (2) High voltage caution label (3) Box label Label ize: mm (L) 56 mm (W) Contents Model: HV7WA- Q`ty: Module Q`ty in one box erial No.: Box erial No. ee next figure for detail description. Date: Packing Date Internal use of Product HV7WA- XX 2X.X.XX Type Grade Line Year Month Internal use erial No PEC. NUMBER PEC TITLE HV7WA- Product pecification 25 OF 28 B26-56-O (3/3) A4(2 X 297)

26 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O PACKING INFORMATION 5. Packing order 5EA Module per Tray 2EA Trays with Cover-Tray PE Bag step PET Tray step4 step2 2EA Cushion -EPE Board per Outer Box EA Module per Outer Box EPE Board Top Cover Outer Box 3layers per Pallet, 6 outer boxes per layer Pallet outer package : Outer Box &Top Cover 8EA Module per Pallet Outer Box step3 5.2 Notes Box Dimension: 55mm(W) x 35mm(D) x 265mm(H) Package Quantity in one Box: pcs Total Weight: 9.66 kg PEC. NUMBER PEC TITLE HV7WA- Product pecification 26 OF 28 B26-56-O (3/3) A4(2 X 297)

27 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O MECHANICAL OUTLINE DIMENION Figure 6. TFT-LCD Module Outline Dimension (Front View) PEC. NUMBER PEC TITLE HV7WA- Product pecification 27 OF 28 B26-56-O (3/3) A4(2 X 297)

28 PRODUCT GROUP REV IUE DATE TFT LCD PRODUCT O Figure 7. TFT-LCD Module Outline Dimensions (Rear view) PEC. NUMBER PEC TITLE HV7WA- Product pecification 28 OF 28 B26-56-O (3/3) A4(2 X 297)