Module Name: DLC0801ZL Record of Revision Date Revision No Summary Rev 1.0 was issued age 2 of 17

Transcription

1 DLC Display Co., Limited 德爾西顯示器有限公司 MODEL No:DLC0801ZL TEL: FAX: EMAL: WEB:

2 Module Name: DLC0801ZL Record of Revision Date Revision No Summary Rev 1.0 was issued age 2 of 17

3 Module Name: DLC0801ZL 1. Scope This data sheet is to introduce the specification of DLC0801ZL active matrix TFT module. t is composed of a color TFTLCD panel, driver Cs, FC and a backlight unit. The 8.01 display area contains 1600 x 3(RGB) x 480 pixels. 2. Application Digital equipments which need color display, rearview mirror, driving recorder etc. 3. General nformation tem Contents Unit Size 8.01 inch Resolution 1600 x 3(RGB) x 480 / nterface LDS / Technology type asi TFT / ixel pitch 40.5(H)x121.5() um ixel Configuration R.G.B stripe Outline Dimension (W x H x D) x 73.0 x 5.4 mm Active Area x mm Display Mode Transmissive, Normally Black / Source Driver C HX8249 Gate Driver C HX8678 Backlight Type LED / age 3 of 17

4 Module Name: DLC0801ZL 4. Outline Drawing age 4 of 17

5 Module Name: DLC0801ZL 5. nterface signals The recommended connector is HROSE FH12A40S0.5SH or equivalent. in No. Symbol /O 1 STBYB Enable C Note2 2 RESET Reset C Note3 3 DD Digital power_ DD Digital power_ SELB 6bit/8bit mode select Note3 6 Ground 7 Ground 8 RXN0 Negative LDS differential data input 9 RXN0+ ositive LDS differential data input 10 Ground 11 RXN1 Negative LDS differential data input 12 RXN1+ ositive LDS differential data input 13 Ground 14 RXCLKN Negative LDS differential data input 15 RXCLKN+ ositive LDS differential data input 16 Ground 17 RXN2 Negative LDS differential data input 18 RXN2+ ositive LDS differential data input 19 Ground 20 RXN3 Negative LDS differential data input 21 RXN3+ ositive LDS differential data input 22 Ground 23 SDN ower for Driver C SDN ower for Driver C SDN ower for Driver C SD ower for Driver C SD ower for Driver C SD ower for Driver C Ground 30 RL Horizontal shift direction Note5 31 TB ertical shift direction Note5 32 ATREN Only for OT program 33 CSB S 34 SCL S 35 SDA S Function Remark age 5 of 17

6 Module Name: DLC0801ZL 36 DD_OT 7.5 for OT program 37 LED LED cathode 38 LED LED cathode 39 LED+ LED anode 40 LED+ LED anode Note 1: : input, O: output, : ower/ground Note 2: STBYB="H(3.3)" : normal operation; STBYB="L()" : timing controller, source driver will turn off, all output are HighZ Note 3: Suggest to connect with an RC reset circuit for stability, Normally pull high. (47kΩ+0.1 uf or external MCU control) Note 4: f LDS input data is 8 bits, SELB must be set to High. Note 5: Scan Control nput RL TB DD DD DD DD Scanning direction Up to down, left to right Up to down, right to left Down to up, left to right Down to up, right to left RL=H TB=H age 6 of 17

7 Module Name: DLC0801ZL 6. Absolute maximum Ratings The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and nonoperational maximum voltage and current values are listed in the table as below: arameter Symbol MN MAX Unit Remark ower Supply oltage DD Note Operating Temperature TO Storage Temperature TST Notes: ermanent damage to the device may occur if maximum values are exceeded functional operation should be restricted to the condition described under normal operating conditions. 7. Electrical Specifications 7.1 Electrical characteristics tem Symbol MN TY MAX Unit ower Supply nput oltage DD ower Supply Ripple oltage R 50 m ower Consumption DD TBD TBD TBD W LTH m LTL m Common input voltage LC id /2 Differential input voltage id H L LDS nterface Differential input high threshold voltage Differential input low threshold voltage CMOS nput high threshold voltage interface nput low threshold voltage Remark 1,2 age 7 of 17

8 Module Name: DLC0801ZL Note 1: The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for DD = 3.3, Frame rate f = 60 Hz and Clock frequency = MHz. Test attern of power supply current is Black. Note 2: The duration of rush current is about 2ms and rising time of power input is 1 ms(min) 7.2 anel Electrical Specifications arameter Symbol MN TY MAX Unit Remark Digital oltage DD ower for driver C & GMA SD ower for driver C & GMA SDN Symbol MN TY MAX Unit Remark Forward Current F ma For each LED Forward oltage F LED life time Hr 7.3 LED Backlight tem Note1: The LED driving condition is defined for each LED channel. Note2: Under LCM operating, the stable forward current should be inputted. And forward voltage is for reference only. Note3: Optical performance should be evaluated at Ta=25 only f LED is driven by high current, high ambient temperature & humidity condition. The life time of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating life time is estimated data. age 8 of 17

9 Module Name: DLC0801ZL 8. Signal timing specifications 8.1 Timing arameters (Sync mode) arameter Symbol DCLK Frequency Fdclk Horizontal valid data Thd alues Min. Typ. Max Unit MHz DCLK Hsync pulse width Thpw DCLK Hsync back porch Thbp DCLK Hsync front porch Thfp DCLK 1 Horizontal line Th DCLK ertical valid data Tvd sync pulse width Tvpw sync back porch Tvbp H H sync front porch Tvfp H Tv H 1 ertical field Remark 480 H Notes: This product is sync mode. age 9 of 17

10 Module Name: DLC0801ZL 8.2 LDS Rx nterface Timing arameter The specification of the LDS Rx interface timing parameter is as below: arameter Clock frequency Symbol RxFCLK alues Min. Typ. Max Unit MHz nput data skew margin TRSKM 500 ps Clock high time TLCH 4/(7*RxFCLK) ns Clock low time TLCL 3/(7*RxFCLK) ns LL wakeup time TenLL 150 us Remark D = 400m RxCM = 1.2 RxFCLK = MHz age 10 of 17

11 Module Name: DLC0801ZL 8.3 nput Signals, Basic Display Colors & Gray Scale of Colors age 11 of 17

12 Module Name: DLC0801ZL 8.4 ower Sequence ower on Sequence Note: 1. When the power supply DD is 0, keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. Backlight must be turn on after power for logic and interface signal are valid. ower off Sequence age 12 of 17

13 Module Name: DLC0801ZL 9. Optical Specification Ta=25 tem Symbol Contrast Ratio CR Response Time Tg Condition Normal θ=φ=0 ΘT iew Angles ΘB ΘL CR 10 ΘR White Chromati city Red Green Blue Min Typ. Max x y x y Typ.0.03 x y x y Unit Remark Note1 Note2 ms Note1 Note3 Degree Note 4 Note5, Note1 Typ Normal θ=φ= Luminance L cd/m2 Note1 Note6 Color Gamut % NTSC % Note1 Note7 Gamma Scale Uniformity U Note 1: Definition of optical measurement system. Temperature = 25 (±3 ) LED backlight: ON, Environment brightness < 150 lx age 13 of 17

14 Module Name: DLC0801ZL Note 2: Contrast ratio is defined as follow: Contrast Ratio = Surface Luminance with all white pixels Surface Luminance with all black pixels Note 3: Response time is defined as follow: Response time is the time required for the display to transition from black to white (Rise Time, Tr) and from white to black(decay Time, Tf). Note 4: iewing angle range is defined as follow: iewing angle is measured at the center point of the LCD. age 14 of 17

15 Module Name: DLC0801ZL Note 5: Color chromaticity is defined as follow: (CE1931) Color coordinates measured at center point of LCD. S area of RGB triangle 100% area of NTSC triangle Note 6: Luminance is defined as follow: Luminance is defined as the brightness of all pixels White at the center of display area on optimum contrast. Note 7: Luminance Uniformity is defined as follow: Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Uniformity (U) = Minimum Luminance( brightness ) in 9 points Maximum Luminance( brightness ) in 9 points Fig. 2 Definition of uniformity age 15 of 17

16 Module Name: DLC0801ZL 10. Environmental / Reliability Tests No Test tem Condition Judgment criteria 1 High Temp Operation Ts=+70, 120hrs er table in below 2 Low Temp Operation Ta=20, 120hrs er table in below 3 High Temp Storage Ta=+80, 120hrs er table in below 4 Low Temp Storage Ta=30, 120hrs er table in below 5 High Temp & Humidity Storage 6 Thermal (Nonoperation) er table in below (polarizer discoloration is excluded) High Ta=+40, 90% RH 120 hours Shock min~ min, Change time:5min, 10 Cycles er table in below C=150pF, R=330Ω 5points/panel er table in below Air:±8K, 5times; Contact:±4K, 5 times; 7 ESD (Operation) 8 Frequency range:10~55hz, Stroke:1.5mm ibration (Nonoperation) er table in below Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X.Y.Z Shock (Nonoperation) ackage Drop Test NSECTON 60G 6ms, ±X,±Y,±Z 3times, for each direction Height:80 cm, 1 corner, 3 edges, 6 surfaces er table in below er table in below CRTERON(after test) Appearance No Crack on the FC, on the LCD anel Alignment of LCD anel No Bubbles in the LCD anel No other Defects of Alignment in Active area Electrical current Within device specifications Function / Display No Broken Circuit, No Short Circuit or No Black line No Other Defects of Display age 16 of 17

17 Module Name: DLC0801ZL 11. recautions for Use of LCD Modules 11.1 Safety The liquid crystal in the LCD is poisonous. Do not put it in your mouth. f the liquid crystal touches your skin or clothes, wash it off immediately using soap and water Handling A. The LCD and touch panel is made of plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. B. Do not handle the product by holding the flexible pattern portion in order to assure the reliability C. Transparency is an important factor for the touch panel. lease wear clear finger sacks, gloves and mask to protect the touch panel from finger print or stain and also hold the portion outside the view area when handling the touch panel. D. rovide a space so that the panel does not come into contact with other components. E. To protect the product from external force, put a covering lens (acrylic board or similar board) and keep an appropriate gap between them. F. Transparent electrodes may be disconnected if the panel is used under environmental conditions where dew condensation occurs. G. roperty of semiconductor devices may be affected when they are exposed to light, possibly resulting in C malfunctions. H. To prevent such C malfunctions, your design and mounting layout shall be done in the way that the C is not exposed to light in actual use Static Electricity A. Ground soldering iron tips, tools and testers when they are in operation. B. Ground your body when handling the products. C. ower on the LCD module before applying the voltage to the input terminals. D. Do not apply voltage which exceeds the absolute maximum rating. E. Store the products in an antielectrostatic bag or container. 11.4Storage A. Store the products in a dark place at +25 ±10 with low humidity (40% RH to 60% RH). Don't expose to sunlight or fluorescent light. B. Storage in a clean environment, free from dust, active gas, and solvent Cleaning A. Do not wipe the touch panel with dry cloth, as it may cause scratch. B. Wipe off the stain on the product by using soft cloth moistened with ethanol. Do not allow ethanol to get in between the upper film and the bottom glass. t may cause peeling issue or defective operation. Do not use any organic solvent or detergent other than ethanol Cautions for installing and assembling Bezel edge must be positioned in the area between the Active area and iew area. The bezel may press the touch screen and cause activation if the edge touches the active area. A gap of approximately 0.5mm is needed between the bezel and the top electrode. t may cause unexpected activation if the gap is too narrow. There is a tolerance of 0.2 to 0.3mm for the outside dimensions of the touch panel and tail. A gap must be made to absorb the tolerance in the case and connector. age 17 of 17