9.0 inch TFT LCD with Capacitive Touch Panel SPECIFICATION

Transcription

1 9.0 inch TFT LCD with Capacitive Touch Panel SPECIFICATION MODEL NAME: LMTAA090YV11- FCJ 1 Date: 2012/11/17 Customer Signature Customer Approved Date Approved By Reviewed By

2 Table of Contents Table of Contents... 2 Record of Revision General Specifications Input/Output Terminals Absolute Maximum Ratings Electrical Characteristics Interface Timing Optical Characteristics Environmental / Reliability Test Precautions for Use of LCD Panels Touch Panel Characteristics Touch Panel Explain LCD Mechanical Drawing Touch Panel Mechanical Drawing...28 Inspection Specification...29 Warranty RMA INTELTRONIC INC.

3 Record of Revision Rev Issued Date Description Editor Preliminary Specification Release 3 INTELTRONIC INC.

4 1 General Specifications 1.1 General Specifications Display Spec Mechanical Characteristics Size Resolution Interface Feature 9 inch Spec 800(RGB) 480 TTL Color Depth 16.7M Technology Type Pixel Pitch (mm) Pixel Configuration Display Mode Surface Treatment (Up Polarizer) Viewing Direction (Note 1) Gray Scale Inversion Direction LCM (W x H x D)(mm) a-si (H) (V) TM with Normally White Anti Glare 12 o clock 6 o clock Active Area (W x H)(mm) With /Without TSP Weight (g)(note 3) R.G.B. Stripe With TSP TBD Note 1: Viewing direction for best image quality is different from TFT definition. There is a 180 degree shift. Note 2: Requirements on Environmental Protection: RoHS Note 3: Weight tolerance: +/- 5% 4 INTELTRONIC INC.

5 2 Input/Output Terminals 2.1 INPUT TERMINALS PIN ASSIGNMENT Pin I/O Symbol No. (Note1) Description Comment 1 LEDA P LED Anode Note1 2 LEDA P LED Anode - 3 LEDK P LED Cathode - 4 LEDK P LED Cathode - 5 GND P Ground - 6 VCOM P Common Voltage - 7 DVDD P Digital power input, - 8 MODE I DE/SYNC mode select. Normally pull high 0 : SYNC mode 1 : DE mode DE Mode: Mode= H, Hsync and Vsync must pull high. - SYNCMode: Mode= L, DE must be connected to GND. 9 DE I DATA INPUT Enable - 10 VSYNC I Vertical Synchronization - 11 HSYNC I Horizontal Synchronization - 12 B7 I Blue data(msb) - 13 B6 I Blue data - 14 B5 I Blue data - 15 B4 I Blue data - 16 B3 I Blue data - 17 B2 I Blue data - 18 B1 I Blue data - 19 B0 I Blue data(lsb) - 20 G7 I Green data(msb) - 21 G6 I Green data - 22 G5 I Green data - 23 G4 I Green data - 24 G3 I Green data - 25 G2 I Green data - 26 G1 I Green data - 27 G0 I Green data(lsb) - 28 R7 I RED data(msb) - 29 R6 I RED data - 30 R5 I RED data - 31 R4 I RED data - 32 R3 I RED data - 33 R2 I RED data - 34 R1 I RED data - 35 R0 I RED data(lsb) - 36 GND P Ground - 5 INTELTRONIC INC.

6 37 DCLK I Parallel RGB clock input - 38 GND P Ground - 39 L/R I Left / Right shift control, 0 : Shift left : S1200S1199 S2S1-1 : Shift right, S1S2S3 S U/D I Up / Down rotate control 0:Up to down G960G959 G2G1-1:Down to up G1G2 G959G VGH P Power supply for Gate on output 42 VGL P Power supply for Gate off output 43 AVDD P Analog power input 44 Reset I Global reset pin 45 NC - 46 VCOM P common voltage 47 Dither I Dithering function enable/disable, 0 :Enable;1: Disable 48 GND P Ground 49 NC - 50 NC - Note1: I/O----definition, I----Input, O----Output, P----Power 2.2 U/D R/L Function Description Scan Control Input UPDN SHLR Scanning Direction GND DVDD Up to Down, Left to Right DVDD GND Down to Up, Right to Left GND GND Up to Down, Right to Left DVDD DVDD Down to Up, Left to Right 3 Absolute Maximum Ratings AGND=GND=0V, Ta = 25 Item Symbol Min Max Unit Remark Digital supply voltage DVDD V - Analog supply voltage AVDD V - Power supply voltage 1 VGH V - Power supply voltage 2 VGL VGH V - Operating temperature T OPR Storage temperature T STG INTELTRONIC INC.

7 4 Electrical Characteristics 4.1 Recommended Operating Condition GND=0V, Ta = 25 Item Symbol Min Typ. Max Unit Remark Digital Supply Voltage DVDD V - Analog Supply Voltage AVDD V - Gate On Voltage VGH V Gate Off Voltage VGL V Common Electrode Driving Signal VCOM V Power Consumption AGND=GND=0V, Ta = 25 Item Symbol Condition Min Typ. Max Unit Remark Digital Supply Current I VCC DVDD=3.3V - TBD ma - Analog Supply Current I AVDD AVDD=10.4V - TBD ma - Gate On Current I VGH VGH=17.0V - TBD ma - Gate Off Current I VGL VGL=-5.0V - TBD ma - Power Consumption Pane l& Gamma - TBD mw - Note1: Checkered flag pattern for Typ.; 4.3 Recommended Driving Condition for Backlight Ta=25 Item Symbol Min Typ Max Unit Remark Forward Current I F - 20 ma Forward Voltage V F V Backlight Power Consumption W BL W 33 LEDs (3 LED Serial, 11 LED Parallel) Operating Life Time - 20, Hrs I F =20mA Note1: The LED driving condition is defined for each LED module (3 LED Serial, 11 LED Parallel).For each LED: I F (1/11) =20mA, V F (1/3) =3.3V. Note2: Under LCM operating, the stable forward current should be inputted. And forward voltage is for reference only. Note3: I F is defined for one channel LED.Optical performance should be evaluated at Ta=25 only 7 INTELTRONIC INC.

8 If LED is driven by high current, high ambient temperature & humidity condition. The life time of LED will be reduced.operating life means brightness goes down to 50% initial brightness. Typical operating life time is estimated data. Note4: The LED driving condition is defined for each LED module 8 INTELTRONIC INC.

9 4.4 Block Diagram 9 INTELTRONIC INC.

10 5 Interface Timing 5.1 AC Electrical Characteristics (For TTL input mode) DVDD=3.3V, Ta= Data input format Horizontal timing 10 INTELTRONIC INC.

11 Vertical timing Horizontal timing 512 Vertical timing Parameter Symbol SPEC Min. Typ. Max. Unit Vertical Display Area tvd 480 th VS period time tv th VS pulse width tvpw th VS Back Porch (Blanking) tvb 32 th VS Front Porch tvfp th DE mode Blanking tv-tvd th 11 INTELTRONIC INC.

12 5.3 Input clock and data timing waveform 5.4 Power ON/OFF Sequence When power on: DVDDVEEVGH When power off: VGHVEEDVDD 12 INTELTRONIC INC.

13 6 Optical Characteristics View Angles Ta=25 Item Symbol Condition Min Typ. Max Unit Remark T B CR10 L R Contrast Ratio CR = Response Time Chromaticity White Red Green Blue T ON T OFF ms x 0.31 y 0.33 x y x y x y Backlight is on TBD TBD TBD TBD TBD TBD Degree Note 2 - Note1 Note3 Note1 Note4 Note5 Note1 NTSC % Note5 Luminance L cd/m Uniformity U % Note1 Note7 Note1 Note6 Test Conditions: 1. The ambient temperature is The test systems refer to Note 1 and Note2. 13 INTELTRONIC INC.

14 Note 1: Definition of optical measurement system The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when measuring the center area of the panel. Item Photo detector Field Contrast Ratio Luminance BM-5A Lum Uniformity 1 Chromaticity SR-3A Response Time TRD100 - Note 2: Definition of viewing angle range and measurement system Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-80). Note 3: Definition of contrast ratio White state : The state is that the LCD should drive by Vwhite. Black state : The state is that the LCD should drive by Vblack. Vwhite: To be determined Vblack: To be determined. Note 4: Definition of response time The response time is defined as the LCD optical switching time interval between White state and 14 INTELTRONIC INC.

15 Black state. Rise time (T ON ) is the time between photo detector output intensity changed from 90% to 10%. And fall time (T OFF ) is the time between photo detector output intensity changed from 10% to 90%. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of luminance uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity (U) = Lmin/ Lmax L----Active area length W---- Active area width Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of luminance Measure the luminance of white state at center point. 15 INTELTRONIC INC.

16 7 Environmental / Reliability Test No. Test Item Condition Remarks High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Storage at High Temperature and Humidity Thermal Shock (non-operation) 7 ESD 8 Vibration Test 9 Mechanical Shock (Non Op) 10 Package Drop Test Note1: Ts is the temperature of panel s surface. Note2: Ta is the ambient temperature of samples. Ts = +70, 240 hours (Note1) Ta = -20, 240 hours (Note) Ta = +80, 240 hours Ta = -30, 240 hours Ta = +60, 90% RH max, 240hours min ~ min, Change time:5min, 20 Cycle C=150pF, R=330, 5point/panel Air: ±8Kv, 5times; Contact: ±4Kv, 5times (Environment: 15~35, 30%~60%. 86Kpa~106Kpa) Frequency range: 10~55Hz Stroke: 1.5mm Sweep: 10Hz~55Hz~10Hz 2 hours for each direction of X.Y.Z. (6 hours for total) Half Sine Wave 60G 6ms, ±X, ±Y, ±Z 3times for each direction Height: 80cm, 1corner, 3edges, 6surfaces IEC :2007 GB IEC :2007 GB IEC :2007 GB IEC :2007 GB IEC :2001 GB/T Start with cold temperature, End with high temperature, IEC :1984,G B IEC :2001 GB/T IEC :1982 GB/T IEC :1987 GB/T IEC :1990 GB/T INTELTRONIC INC.

17 8 Precautions for Use of LCD Panels 8.1 Handling Precautions The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary The polarizer covering the display surface of the LCD Panel is soft and easily scratched. Handle this polarizer carefully If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents Do not attempt to disassemble the LCD Panel If the logic circuit power is off, do not apply the input signals To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment Be sure to ground the body when handling the LCD Panels Tools required for assembly, such as soldering irons, must be properly ground To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions The LCD Panel is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 8.2 Storage precautions When storing the LCD Panels, avoid exposure to direct sunlight or to the light of fluorescent lamps The LCD Panels should be stored under the storage temperature range. If the LCD Panels will be stored for a long time, the recommend condition is: Temperature : 0 40, Relatively humidity: 80% The LCD Panels should be stored in the room without acid, alkali and harmful gas. 9.3 Transportation Precautions The LCD Panels should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 17 INTELTRONIC INC.

18 9 Touch Panel Characteristics 9.1 Scope This specification applies to consumer electronics the capacitive touch screen (such as MID, multipoint vehicle DVD, etc.). 9.2 Features and General Specifications General Specifications (L=Length W=Width T=Thickness) Items structure Outline Dimensional View Area Active Area Pin Configuration Specifications P/G Refer to Engineering Drawing Refer to Engineering Drawing Refer to Engineering Drawing Refer to Engineering Drawing 9.3Environment Conditions Items Value Operating Temperature & Humidity -20~70, 90%RH Storage Temperature & Humidity -30~80, 90%RH 9.4Mechanical characteristics Items Finger contact area Optical Characteristics Surface Hardness Value 5mm Transmittance 3H 18 INTELTRONIC INC.

19 9.5 Electric Characteristics Items Value Working voltage Insulation Resistance Working current Response time DC2.8V~3.3V > 20M DC25V 12mA~14.5mA 16ms 9.6 Testing Condition Temperature and humidity range: In room temperature conditions (5-35 ), humidity for 45% - 85%, and barometric pressure test 1060hPa 860hPa - under. Necessary to products accurately, should be in standard test for: 23, environment and placed 1013hPa 65% RH and 24 hours later, tested. 9.7 Impact Resistance Test 1Test conditions: when using 64g Φ 25.4 mm ball from 60cm height vertical fell on the thickness of the glass is 0.7 mm mm product surface center once, glass won't damaged. 2 ) Determine the benchmark: after the experiment, and various features meet product is less than 20% changes rate. 9.8 FPC Bending and Heat Resistance 1 FPC peeling strength X2000g peeling by horizontal 180 TFT Y500g ( peeling by upward 90) Z150g Stripping vertical direction 2 FPC bending resistance 1mm bending radius, bending 3 times, to meet the requirements of electrical performance 19 INTELTRONIC INC.

20 9.9 Electric characteristics Insulation resistance Ω > 20M Appearance standard Dot-like and Linear Matter: Under 12~20W cold what fluorescent lighting Visual distance: 18~20cm Put the test sample to black cardboard. Observation done within 5 seconds. black cardboard 20 INTELTRONIC INC.

21 RemarkD-diameter, L-length, W-width, GT-glass thickness Test items Judge criterion Granular sundry Product size: smaller the 7 inches dot-like D0.1mm ignore 0.10mm dot-like D 0.20mm Space between two dots-like is 10mm, only 2 are allowed; dot-like D0.20mm Not allowed Granular sundry Product size: 7 inches above (including 7 inch) ~ 10.1 inch (including 10.1 inch) dot-like D 0.10mm ignore 0.10mmdot-like D 0.25mm Space between two dots-like is 20mm,Only 3 are allowed; dot-like D0.25mm Not allowed Granular sundry Product size: 10.1 inches above dot-like D 0.20mm ignore 0.20mmdot-like D 0.3mm 0.02 mm acuities linear sundry wide Space between two dots-like is 20mm,Only 3 are allowed; W 0.02 mm Can ignore 0.02mm Linear W 0.03mm L 3.0mm, allowed two 0.03mm Linear W 0.05mm L 2.0mm, Only allow one Linear W>0.05mm and L 3.0mm Not allowed 21 INTELTRONIC INC.

22 Chip and Crack : Corner chip: X 1.5mm, Y 0.5mm and Z GT, ignored 1If corner chip located outside the contact side, which affect product function seriously, the TP is defective 2If corner chip located on circuit,which affect product function seriously, the TP is defective Side Chip: X 3.0mm, Y 0.5mm and Z GT, ignored 1If side chip located outside the contact side, which affect product function seriously, the TP is defective 2If side chip located on circuit,which affect product function seriously, the TP is defective Crack: The TP is defective 22 INTELTRONIC INC.

23 9.11 Reliability Test Conditions Temperature and Humidity strorage: High temperature storage : Thermal Shock: LMTAA090YV11-FCJ1 At 60, 90% RH conditions 240 hours, remove deposit in normal temperature often wet all electrical parameters meet. The requirements in 6 shall be satisfied after exposing at 70,for 240 Hours and at nomal temperature and humidity for 24 hours. According to - 20 (0.5 hour) - 70 (0.5 hour) conditions, take out 5 times in circulation under normal temperature often wet store again after 24 hours, meet the electrical parameters. 23 INTELTRONIC INC.

24 9.12 Using Precautions Cautions for Storage : Product has to storage under the environment specified by this spec, and cannot neither put under direct direct sunlight nor press with heavy weight. Cautions for unpacking : 1Mining the times of handling 2Useing handling tools. 3No more than three layer, pile up gentle with place. Assembly precautions : 1Do not exert extra force to touch panel 2Since touch panel is transparent and clear, make sure to wear fingerstall or glove before touching. Be careful your hands and other parts from injury at handling by glass corners. 3When handling, make sure to hold the touch panel borders not center parts to avoid dirt to touch panel. Do not lift touch panel by tail to avoid tail from loosen 4When installing and assembling, do not lift tail with heavy force to avoid tail from peeling off touch panel. 5Do not stick or mount other parts on the tail, such as additional film or metal plate. As it will exert extra force to tail tip and cause tail loosen. 6Please don't pull makes force from side to side, because the FPC tension will make FPC burst. 7If there is air groove on touch panel, when design product structure, make sure no liquid and powder near the air groove. 8 In order to avoid heavy stress to touch panel surface, make sure to keep 0.2mm-0.5mm assembling gap between touch panel and case. 24 INTELTRONIC INC.

25 10 Touch Panel Explain 10.1 Flow Chart Start Power on Initialize IIC Wait 200 ms Receive data form TP Send data If a finger touch? No Yes Send data package If a finger touch? No Yes Green mode: <48ms Sleep mode : <642.5ms Initialization : <642.5ms Send data package 10.2 Principle diagram VDD Capacitive touch panel + Driver IC SDA SCL... MCU LCD... GND 25 INTELTRONIC INC.

26 10.3 Software Show Touch IC Software Show Master interface type and device address This touch IC is communicated by I2C interface. Maximum transportation rate is 250K dps. Address of hardware is 0 b x, X is i the read/write control bit( ).. 0 means HOST is writing data to TOUCH IC, 1 means HOST is reading data fromm TOUCH IC. So that please input 0XAA when HOST is writing data to TOUCH IC. Input 0XAB when HOST is reading data from TOUCH IC. Normal (pull low) (pull high) Touch Trigger No touch within 3 seconds. Sleep Green When HOST switch to STANDBY mode, please set SHUTDOWN pin to high level. This will let the TOUCH IC switch to SLEEP mode to save the power consumption. 1.) Normal Mode The fastest updating speed off TOUCH IC s coordinate is 16ms. This T is the most power consumption mode. While stop touching 3 seconds, will switch to Green Mode. 2.) Green Mode The updating speed of TOUCH IC s coordinate is 48ms. While touching the touch screen, will switch to Normal Mode right away. 3.) Sleep Mode When SHUTDOWN pin is low level, thee TOUCH IC will switch to Normal Mode. When SHUTDOWN pin is high level, thee TOUCH IC will switchh to Sleep Mode. 26 INTELTRONIC INC.

27 11 LCD Mechanical Drawing 27 INTELTRONIC INC.

28 12 Touch Panel Mechanical Drawing Tolerance no specified: Storage Temp. & Humidity: Surface Hardness: 3H Operation Temp. & Humidity: Remarks: FRONT VIEW Black T=0.125mm SIDE VIEW LED Hole Camera Hole DST: REAR VIEW 28 INTELTRONIC INC.

29 13. Inspection Specifications The buyer (customer) shall inspect the modules within twenty calendar days since the delivery date (the "inspection period ) at its own cost. The results of the inspection (acceptance or rejection) shall be recorded in writing, and a copy of this writing will be promptly sent to the seller. The buyer may, under commercially reasonable reject procedures, reject an entire lot in the delivery involved if, within the inspection period, such samples of modules within such lot show an unacceptable number of defects in accordance with this incoming inspection standards, provided however that the buyer must notify the seller in writing of any such rejection promptly, and not later than within three business days of the end of the inspection period. Should the buyer fail to notify the seller within the inspection period, the buyer's right to reject the modules shall be lapsed and the modules shall be deemed to have been accepted by the buyer. 14. Warranty Inteltronic Inc. warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. Inteltronic Inc. will be limited to replace or repair any of its module which is found and confirmed defective electrically or visually when inspected in accordance with Inteltronic Inc. general module inspection standard. This warranty does not apply to any products which have been on customer s production line, repaired or altered by persons other than repair personnel authorized by Inteltronic Inc., or which have been subject to misuse, abuse, accident or improper installation. Inteltronic Inc. assumes no liability under the terms of this warranty as a consequence of such events. If an Inteltronic Inc. product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. In returning the modules, they must be properly packaged with original package; there should be detailed description of the failures or defect. 15. RMA Products purchased through Inteltronic Inc. and under warranty may be returned for replacement. Contact support@inteltronicinc.com for RMA number and procedures 29 INTELTRONIC INC.

30 Inteltronic Inc. Office: Fax: Address: Union City Blvd Union City, CA Wah Lee Industrial Corp. HSINCHU OFFICE 18F, No.8, Zihciang S. Rd., Jhubei, Hsinchu 302, Taiwan, R.O.C. Tel : FAX: INTELTRONIC INC.