DSA8300 Datasheet Digital Serial Analyzer Sampling Oscilloscope

Transcription

1 DSA8300 Datasheet Digital Serial Analyzer Sampling Oscilloscope Key features With today s sampling module portfolio, the DSA8300 supports up to 8 simultaneously acquired signals A wide variety of optical, electrical, and accessory modules to support your specific testing requirements The DSA8300 is a state-of-the-art Equivalent Time Sampling Oscilloscope that provides the highest fidelity measurement and analysis capabilities for Communications Signal Analysis, Serial Data Network Analysis, and Serial Data Link Analysis applications. Key performance specifications Very low time base jitter: 425 fs typical on up to 8 simultaneously acquired channels <100 fs on up to 6 channels with 82A04B phase reference module Industry s highest vertical resolution 16 bit A/D Electrical resolution: <20 µv LSB (for 1 v full range) Optical resolution from <20 nw for the 80C07B (1 mw full range) to <0.6 µw for the 80C10C (30 mw full range) Optical bandwidths to >80 GHz Electrical bandwidths to >70 GHz Over 120 automated measurements for NRZ, RZ, and pulse signal types Automated mask testing with over 80 industry-standard masks Optical modules Fully integrated optical modules that support all standard optical data rates from 155 Mb/s to 100 Gb/s Certified optical reference receivers support specified requirements for standards-mandated compliance testing Optical bandwidths to >80 GHz High optical sensitivity, low noise, and wide dynamic range of the optical sampling modules allows accurate testing and characterization of short-reach to long-haul optical communications standards Fully calibrated clock recovery solutions no need to manually calibrate for data pick-off losses Calibrated extinction ratio measurements ensure repeatability of extinction ratio measurements to <0.5 db among systems with modules with this factory calibration option Electrical modules Very low-noise electrical samplers (280 μv at 20 GHz, 450 μv at 60 GHz, typical) Selectable bandwidths 1 allow the user to trade-off sampler bandwidth and noise for optimal data acquisition performance Remote samplers 2 or compact sampling extender module cables support minimal signal degradation by allowing the sampler to be located in close proximity to the device under test World s highest-performance integrated TDR (10 ps typical step rise time) supports exceptional impedance discontinuity characterization and high dynamic range for s-parameter measurements to 50 GHz 1 With 80E07B, 80E08B, 80E09B, 80E10B, 80E11, and 80E11X1 modules. 2 80E07B, 80E08B, 80E09B and 80E10B only. 1

2 Datasheet Analysis Complete suite of over 120 automated measurements for NRZ, RZ, and pulse signal types Automated Mask Testing with over 80 Industry-standard Masks. New Masks can be Imported into the DSA8300 to support New Emerging Standards. Users can Define their own Masks for Automated Mask Testing Vertical and Horizontal Histograms for Waveform Statistical Analysis Vertical, Horizontal, and Waveform Cursors (with measurements) Jitter, Noise, BER, and Serial Data Link Analysis is provided through the 80SJNB Basic and Advanced Software Application Options Advanced TDR Analysis, S-parameter measurements, simulation model extraction, and serial link simulation capabilities are provided through the IConnect Software Application options High test throughput High sample acquisition rate up to 300 ks/s per channel Efficient programmatic interface (IEEE-488, Ethernet, or local processor access) enables high test throughput Optical eye diagram testing Applications Design/Verification of telecom and datacom components and systems Manufacturing/testing for ITU/ANSI/IEEE/SONET/SDH compliance High-performance true-differential TDR measurements Impedance characterization and network analysis for serial data applications including S-parameters Advanced jitter, noise, and BER analysis Channel and eye diagram simulation and measurement-based SPICE modeling Superior performance with extraordinary versatility The DSA8300 Digital Serial Analyzer is the most versatile tool for developing and testing communications, computers, and consumer electronics which use multi-gigabit data transmission. It is used for optical and electrical transmitter characterization, as well as compliance verification for devices, modules, and systems used in these products. In addition, the DSA8300 is well-suited for electrical signal path characterization, whether for packages, PCBs, or electrical cables. With exceptional bandwidth, signal fidelity, and the most extensible modular architecture, the DSA8300 provides the highest-performance TDR and interconnect analysis, most accurate analysis of signal impairments, and BER calculations for current and emerging serial data technology. Passive interconnect test Finally, with its exceptional signal fidelity and resolution, the DSA8300 is the gold standard for electrical and optical applications which require ultrahigh bandwidths, very fine vertical resolution, low jitter, and/or exceptional time interval accuracy. The DSA8300 provides unmatched measurement system fidelity with the lowest native instrument jitter floor (425 fs RMS, typical for serial data signals at rates >1.25 Gb/s) that ensures the most accurate acquisition of up to 8 high-bandwidth signals simultaneously. You get additional analysis benefits from acquisition jitter as low as 100 fs RMS when using the 82A04B Phase Reference module. The multiprocessor architecture, with dedicated per-slot digital signal processors (DSPs), provides fast waveform acquisition rates, reducing the test times necessary for reliable characterization and compliance verification. 2

3 DSA8300 Digital Serial Analyzer Sampling Oscilloscope The DSA8300 s versatile modular architecture supports a large and growing family of plug-ins enabling you to configure your measurement system with a wide variety of electrical, optical, and accessory modules that best suit your application now and in the future. With 6 module slots, the DSA8300 can simultaneously accommodate a Clock Recovery module, a precision Phase Reference module, and multiple acquisition modules (electrical or optical), so you can match system performance to your evolving needs. The ability to swap sampling modules without powering down the DSA8300 (available for scopes with firmware versions 6.1 and later) provides additional flexibility in configuring your DSA8300 to changing test needs. Featuring industry-leading signal fidelity, the family of electrical modules includes bandwidth performance from 20 GHz to >70 GHz, while the optical modules support optical testing from 125 Mb/s to 100 Gb/s and beyond with optical bandwidth exceeding 80 GHz. The DSA8300 supports all of the legacy 8000 Series electrical and optical sampling modules and accessories. 3 In addition, specialized modules supporting features such as single-ended and differential electrical clock recovery, electrostatic protection for electrical samplers, and connectivity to the popular TekConnect probing system brings you the performance of state-of-the-art Tektronix probes for high-impedance and differential probing. Low-impedance probes for 50 Ω probing and for TDR probing are also available. The raw acquisition performance of the DSA8300 and its sampling modules and accessories is further augmented by the comprehensive measurement and analysis capabilities of the DSA8300 and its associated software applications. For example, the IConnect software applications provide complete TDR, S-parameter, and signal integrity analysis for passive electrical interconnects (packages, printed circuit boards, backplanes, cable, etc.) while the 80SJNB applications provide complete jitter, noise, and bit error rate analysis as well as channel and equalization analysis and emulation for both optical and electrical serial data links. Jitter, noise, BER, and serial data link analysis Jitter, noise and BER analysis High-speed serial data link measurements and analysis are supported with three software solutions: 80SJARB, 80SJNB essentials, and 80SJNB Advanced. 4 80SJARB (Option JARB) is a basic jitter measurement tool capable of measuring jitter on any waveform random or repetitive. The simplicity of acquisition limits the amount of analysis possible so only the simplest decomposition can be used; repeatability is pattern dependent 80SJNB Essentials (Option JNB) offers complete analysis of jitter, noise, and BER, with decomposition of components for clear understanding of a signal s problems and margins. The acquisition methodology requires a repetitive pattern. Both accuracy and repeatability are improved relative to 80SJARB since the tool has access to the complete signal pattern 80SJNB Advanced (Option JNB01) adds features to 80SJNB Essentials for serial data link analysis de-embedding of fixture, channel emulation, FFE/DFE equalization, and preemphasis/deemphasis 3 The DSA8300 does not support the 80A06 Pattern Synchronization module, as this capability is superseded by the integrated Advance Trigger option (Option ADVTRIG) for the DSA These software applications can be purchased to install on currently owned DSA8300 oscilloscopes with the DSA83UP upgrade kits. 3

4 Datasheet Jitter analysis of arbitrary data (80SJARB) The 80SJARB jitter measurement application software for the DSA8300 Series addresses IEEE 802.3ba applications requiring the J2 and J9 jitter measurements. It also enables basic jitter measurements for NRZ data signals including PRBS31, random traffic, and scrambled data. This provides an entry-level jitter analysis capability with simple Dual Dirac model jitter analysis and no pattern synchronization requirement. 80SJARB can acquire continuously in Free Run mode, delivering acquisitions and updates beyond the IEEE minimum requirement of 10,000 data points. Plots include jitter and eye opening bathtub curves for both measured and extrapolated data, as well as a histogram of the acquired data. 80SJARB jitter analysis measurements Measurement Description J2 Total jitter for BER = 2.5e 3 J9 Total jitter for BER = 2.5e 10 Tj Total jitter for BER = 2.5e 12 DJ dd RJ dd Deterministic jitter (Dual Dirac model) Random jitter (Dual Dirac model) 80SJNB jitter and noise analysis measurements 80SJNB jitter analysis Measurement TJ at BER Description Total jitter at specified BER J2 Total jitter for BER = 2.5e 3 J9 Total jitter for BER = 2.5e 10 RJ RJ(h) RJ(v) RJ(d-d) DJ DDJ DDPWS DCD DJ(d-d) PJ PJ(h) PJ(v) EO at BER BUJ NPJ SSCMagnitude SSCFrequency Random jitter Horizontal component of random jitter Vertical component of random jitter Random jitter according to the Dual Dirac model Deterministic jitter Data-dependent jitter Data-dependent pulse width shrinkage Duty cycle distortion Deterministic jitter computed in the Dual Dirac model Periodic jitter Horizontal component of periodic jitter Vertical component of periodic jitter Horizontal eye opening at specified BER Bounded uncorrelated jitter Non-periodic jitter (uncorrelated and bounded) Magnitude of SSC modulation in ppm Frequency of SSC modulation in ppm 80SJNB noise analysis Measurement RN RN(v) RN(h) DN Description Random noise Vertical component of random noise Horizontal component of random noise Deterministic noise DDN1 Data-dependent noise on logical level 1 DDN0 Data-dependent noise on logical level 0 PN PN(v) PN(h) EO at BER BUN NPN Periodic noise Vertical component of periodic noise Horizontal component of periodic noise Vertical eye opening at specified BER Bounded uncorrelated noise Non-periodic noise 80SJNB Advanced (Opt. JNB01) supports: FFE (Feed Forward Equalization) to 100 Taps DFE (Decision Feedback Equalization) to 40 Taps Filter for support of linear filters from fixture de-embed to transmitter equalization. Channel emulation supported for channels with >30 db of loss at 1st harmonic frequency TDR (Time Domain Reflectometry) applications Quickly identify the exact location of faults with the 80E10B sub-millimeter resolution and IConnect True Impedance Profile 4

5 DSA8300 Digital Serial Analyzer Sampling Oscilloscope The DSA8300 is the industry s highest-performance fully integrated Time Domain Reflectometry (TDR) measurement system. Offering truedifferential TDR measurements up to 50 GHz bandwidth with 15 ps reflected rise time and 12 ps incident rise time 5, the DSA8300 enables you to keep pace with today s most demanding Serial Data Network Analysis (SDNA) requirements. The 80E10B and 80E08B TDR modules feature a fully integrated independent dual-channel 2-meter remote sampler system to minimize fixturing and assure optimal system fidelity. Independent sampler deskew ensures fast and easy fixture and probe de-embedding. The user can characterize differential crosstalk by using TDR steps from a differential module to drive one line pair while monitoring a second line pair with a second differential module. The DSA8300 is the industry s most versatile TDR measurement system, accommodating up to 4 dual-channel true-differential TDR modules for fast, accurate multilane impedance and S-parameter characterization. The P80318 True-differential TDR probe and P8018 Single-ended Passive Handheld TDR probe provide high-performance probing solutions for circuit board impedance and electrical signal characterization. The P80318, an 18 GHz 100 Ω input-impedance differential TDR hand probe, enables highfidelity impedance measurements of differential transmission lines. The adjustable probe pitch enables a wide variety of differential line spacing and impedances. The P8018 is a 20 GHz Single-ended Passive Handheld TDR probe. Both the P80318 and P8018 can be used as stand-alone probes but are especially designed to work with the 80A02 EOS/ESD module to provide EOS/ESD protection. Multi-gigabit signal path characterization and analysis Serial Data Network Analysis (SDNA) As clock speeds and rise times of digital circuits increase, interconnect signal integrity dramatically affects digital system performance. Accurate and efficient Serial Data Network Analysis (SDNA) of the signal path and interconnects in time and frequency domains is critical to predict signal losses, jitter, crosstalk, terminations and ringing, digital bit errors, and eye diagram degradation, ensuring reliable system operation. Tektronix offers several true-differential TDR modules, which in combination with IConnect software allow S-parameter measurements with up to 70 db of dynamic range. This performance assures accurate, repeatable measurements in serial data analysis, digital design, signal integrity, and electrical compliance testing applications. TDR module performance with IConnect TDR Module 80E10B 80E08B 80E04 S-parameter measurement bandwidth performance 50 GHz 30 GHz 20 GHz With the long record length acquisitions, IConnect provides great flexibility for obtaining the desired frequency range and frequency step when performing S-parameter measurements. Up to 1,000,000 points can be acquired. When you use IConnect Signal Integrity TDR and S-parameter software with the DSA8300 you have an efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of multi-gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter, and eye-diagram tests, and fault isolation. IConnect can help you complete interconnect analysis tasks in minutes instead of days, resulting in faster system design time and lower design costs. IConnect also enables impedance, S-parameters, and eye-diagram compliance testing as required by many serial data standards, as well as full channel analysis, Touchstone (SnP) file output, and SPICE modeling for multi-gigabit interconnects. Serial data network analysis 5 Rise times are 10-90%. Typical reflected rise times for the 80E10B are <10 ps. 5

6 Datasheet Failure analysis quickly identify fault location The 80E10B, with its 12 ps typical TDR rise time, provides superior resolution enabling the fastest and most efficient fault isolation in package, circuit board, and on-chip failure analysis applications. IConnect Signal Integrity TDR and S-parameter software Operating on the DSA8300 TDR platform, IConnect S-parameters is the most cost-effective and highest throughput approach for S-parameter measurements in digital design, signal integrity analysis, and interconnect compliance testing, providing as much as 50% cost savings compared to similar bandwidth VNAs, and dramatically speeding up measurements. You can also take advantage of the IConnect S-parameters command-line interface, which automates the S-parameter measurements to the overall suite of manufacturing tests you perform using your TDR instrument, significantly reducing test time while increasing measurement repeatability. The simplicity of S-parameter calibration using a reference (open, short, or through), and an optional 50 Ω load makes measurements, fixture deembedding, and moving the reference plane a snap. Touchstone file format output enables easy S-parameter file sharing for further data analysis and simulations. Tektronix offers several true-differential TDR modules, which in combination with IConnect offers S-parameter measurements up to 50 GHz with up to 70 db of dynamic range. This performance exceeds requirements for serial data analysis, digital design, and signal integrity applications, resolving down to 1% ( 40 db) accuracy of crosstalk, while electrical compliance testing masks typically call for measurements in the 10 to 30 db range. IConnect software lets you: Quickly and easily generate SPICE and IBIS models for your PCBs, flex boards, connectors, cables, packages, sockets, and I/O buffer inputs directly from TDR/T or VNA S-parameter measurements Display eye diagram degradation, jitter, loss, crosstalk, reflections, and ringing in your digital system Substantially simplify the signal integrity analysis of the interconnect link, equalization and emphasis component design, and analysis of the interconnect link with transmitter and receiver IConnect Linear Simulator lets the designer link several interconnect channels together to evaluate the total time, frequency domain performance, and eye diagram of the overall channel For more information regarding the IConnect software applications, see the IConnect Signal Integrity, TDR, and S-Parameter SW 80SICMX 80SICON 80SSPAR datasheet. Measurement and analysis tools for optical testing applications The DSA8300 includes a wide variety of measurement and analysis tools which specifically address optical testing applications. In addition to the standard amplitude and timing parametric measurements (such as rise/fall times, amplitude, RMS jitter, RMS noise, frequency, period, etc.), the measurement suite for the DSA8300 includes measurements specifically tailored to measuring optical signals (average optical power, extinction ratio, eye height, eye width, optical modulation amplitude (OMA), etc.). For a complete list of measurements, see the Measurement section of this datasheet. The DSA8300 also includes standard compliance testing masks for all of the common optical standards from 155 Mb/s to 100 Gb/s. The DSA8300 mask testing system includes the ability to automatically fit standard and user masks to data acquired into a waveform database. The mask test system can also automatically determine the mask margin based either on the total # of mask violations or the "hit ratio" of mask violation to the number of samples acquired in the mask test unit interval. Users can also create their own masks for automated mask testing. Histograms and cursor measurements are also available to analyze optical signals acquired by the DSA8300. Finally, the 80SJNB applications support complete jitter, noise, and BER analysis for optical signals. The advanced version of this software (Option JNB01) supports evaluating the emphasis and equalization on impaired signals. Sampling modules High speed optical test solutions The DSA8300 with its highly configurable mainframe and a wide variety of optical modules provide complete optical test solutions with superior system fidelity from 125 Mb/s to 100 Gb/s and beyond. The modules cover a range of wavelengths for both single- and multi-mode fibers. Each module can be optionally configured with several selectable Optical Reference Receiver (ORR) filters and/or a full bandwidth path. Each module also supports fully calibrated clock recovery solutions (whether integrated into the module or through a data pick-off routed to an external clock recovery module or stand-alone clock recovery instrument). See the Optical sampling modules table for a brief description of each available optical sampling module. See the Optical sampling module selection guide table for key specifications for each module. For more complete information on these modules, see the Optical Sampling Modules 80C07B 80C08D 80C10C 80C11B 80C12B 80C14 80C15 datasheet. 6

7 DSA8300 Digital Serial Analyzer Sampling Oscilloscope Optical sampling modules Module 80C07B Multirate Datacom and Telecom 80C08D Multirate, Broad Wavelength, High Sensitivity 10 Gb/s 80C10C Multirate Datacom and Telecom 40 Gb/s and 100 Gb/s 80C11B Multirate 10 Gb/s Datacom and Telecom 80C12B Multirate Datacom and Telecom Description The 80C07B module is a broad-wavelength (700 to 1650 nm) multirate optical sampling module optimized for testing datacom/ telecom signals from 125 Mb/s to 2.5 Gb/s. With its amplified O/E converter design, this module provides excellent signal-to-noise performance, allowing users to examine low-power optical signals. The 80C07B can be optionally configured with fully calibrated internal clock recovery that supports 125, 155, 622, 1063, 1250, 2125, 2488, 2500, and 2666 Mb/s rates. The 80C08D module is a broad-wavelength (700 to 1650 nm) multirate optical sampling module providing datacom rate testing for 10GbE, 40GbE-R4, 100GbE-SR10 applications at 9.953, , Gb/s and 10G Fibre Channel applications at and Gb/s. The 80C08D also provides telecom rate testing at 9.953, , and Gb/s. With its amplified O/E converter design, this module provides excellent signal-to-noise performance and high optical sensitivity, allowing users to examine low power level optical signals. The 80C08D can be optionally configured with an integrated clock recovery option that supports acquiring signals at any standard- or user-specified rate from 9.8 to 12.6 Gb/s. The 80C10C module provides integrated and selectable reference receiver filtering, enabling conformance testing at either 1310 nm or 1550 nm of all standard 25, 40 and 100 (4 x 25) Gb/s standard rates. There are three configurations for the 80C10C: Option F1: Provides standard compliant optical reference receivers for the following rates (standards): Gb/s (100GBase-LR4 and 100GBase-ER4) Gb/s (OTU4) Gb/s (OC-768/STM-256, VSR2000 G.693, 40G NRZ G.959.1) Gb/s (40GBase-FR) Gb/s (G.709 FEC, OTU3 4 10G LAN PHY) Option F2: Provides standard compliant optical reference receivers for the following rates (standards): Gb/s (100GBase-LR4 and 100GBase-ER4) Gb/s (OTU4) Option F3: Provides standard compliant optical reference receivers for the following rates (standards): Gb/s (OC-768/STM-256, VSR2000 G.693, 40G NRZ G.959.1) Gb/s (40GBase-FR) Gb/s (G.709 FEC, OTU3 4 10G LAN PHY) In addition to the filter rates, the user may also select bandwidths for the 80C10C for optimal noise vs. bandwidth performance for accurate signal characterization. When equipped with Option CRTP an electrical signal pickoff is provided for clock recovery. Clock recovery, to 28.6 Gb/s, for the 80C10C is provided using the CR286A clock recovery instrument (sold separately). When equipped with Option HSPR, a separate high-sensitivity photo receiver is provided with independent electrical outputs that can be used with external equipment (such as a Tektronix BERTScope) for high accuracy optical measurements. The 80C10C is also optionally available in a bundled ordering configuration which includes a single-channel 70+ GHz electrical sampling module. The 80C11B module is a long-wavelength (1100 to 1650 nm) multirate optical sampling module optimized for testing 10 Gb/s datacom and telecom standard rates at 9.953, , , , , , , and Gb/s. With its high optical bandwidth of up to 30 GHz (typical) it is well-suited for general-purpose high-performance 10 Gb/s optical component testing. The 80C11B can be optionally configured with clock recovery that can support any standard or user-defined rate in the continuous range from 9.8 to 12.6 Gb/s. The 80C12B module is a broad wavelength (700 to 1650 nm) multirate optical sampling module providing telecom and datacom testing for standards from 155 Mb/s to 11.4 Gb/s. This highly flexible module can be configured to support a wide variety of 10 Gb/s applications, lower data rate applications (155 Mb/s to 7.4 Gb/s), or a combination of 10G and lower data rate standards. The low data rate applications include: Telecom applications from 155 to 2666 Mb/s, 1G, 2G, and 4G Fibre Channel, multilane standards such as 10GBASE-X4 and 4-Lane 10 Gb/s Fibre Channel, and Infiniband SDR and DDR rates. The supported 10 Gb/s application includes both datacom and telecom standards. The supported 10 Gb/s datacom applications include 10GbE, 40GbE-R4, 100GbE-SR10 applications at 9.953, , Gb/s, and 10G Fibre Channel applications at Gb/s and Gb/s. The 80C12B also provides telecom rate testing at 9.953, , and Gb/s. With its amplified O/E converter design, this module provides excellent signal-to-noise performance and high optical sensitivity, allowing users to examine low-power optical signals. Clock recovery for the 80C12B is provided using the 80A05 module or CR125A clock recovery instrument (sold separately). 7

8 Datasheet Module 80C14 Multirate Datacom and Telecom 80C15 Description The 80C14 module is a broad-wavelength (700 to 1650 nm) multirate optical sampling module providing 8G, 10G, and 16G telecom and datacom testing. The supported 10 Gb/s datacom applications include: 10GbE, 40GbE-R4, 100GbE-SR10 applications at 9.953, , and Gb/s. Fibre Channel applications include: 8.500, , , and Gb/s. The 80C14 also provides telecom rate testing at 9.953, , , and 12.5 Gb/s. With its amplified O/E converter design, this module provides excellent signal-to-noise performance and high optical sensitivity, allowing users to examine low power level optical signals. Clock recovery for the 80C14 is provided by the CR175A or CR286A (sold separately). The 80C15 module provides integrated and selectable reference receiver filtering, enabling conformance testing for single- and multimode optical signals at 850 nm, 1310 nm or 1550 nm of all standard Gb/s standard rates. This module provides bandwidth filters for the following rates (standards): Gb/s (100GBase-ER4, 100GBase-LR4, 100GBase-SR4, Infiniband EDR) Gb/s (OTU4) Gb/s (32G Fibre Channel) In addition to the filter rates, the user may also select bandwidths for the 80C15 for optimal noise vs. bandwidth performance for accurate signal characterization. Optical sampling module selection guide Characteristic Wavelength Range (nm) Unfiltered Optical Bandwidth (GHz) Fiber Input (μm) Mask Test Sensitivity (dbm) 80C07B 6 80C08D 80C12B 7 Opt. F0-F12 80C12B 7 Opt. 10G/ 10GP 80C14 80C11B 80C15 80C10C 8 Opt F C10C 8 Opt F , 50, , 50, , 50, , 50, , 50, , 50, Optical reference receivers supported 155 mb/s 622 mb/s Gb/s Gb/s Gb/s Gb/s Gb/s 2.66 Gb/s Gb/s Gb/s 80C10C 8 Opt F There are specific reference receiver groupings supported for the 80C07B. See the 80Cxx Optical Module datasheet for detailed information. 7 There are specific reference receiver groupings supported for the 80C12B. See the 80Cxx Optical Module datasheet for detailed information. 8 The clock recovery trigger pick-off (Option CRTP) for the 80C10C can support trigger pick-off for data rates to >43 Gb/s. 9 The full 12 GHz bandwidth for the 80C12B is only available with Option F0, 10G, or 10GP. 10 Mask test sensitivity of the 80C08D reduced by ~1 dbm with internal clock recovery options. 11 Mask test sensitivity of the 80C10C reduced by ~0.6 dbm with internal clock recovery trigger pick-off (Option CRTP). 8

9 DSA8300 Digital Serial Analyzer Sampling Oscilloscope Characteristic 80C07B 6 80C08D 80C12B Gb/s Gb/s Gb/s Gb/s Opt. F0-F12 80C12B 7 Opt. 10G/ 10GP Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s 11.1 Gb/s 11.3 Gb/s Gb/s Gb/s 80C14 80C11B 80C15 80C10C 8 Opt F Gb/s Gb/s Gb/s 80C10C 8 Opt F Gb/s Gb/s Gb/s 80C10C 8 Opt F3 Clock recovery for optical testing In many optical applications, there is no data clock directly available to provide a reference signal for acquiring the signals from the device under test. In these situations, it is necessary to recover the clock from the data signal. The Tektronix 8000 Series of sampling oscilloscope products provides a complete complement of clock recovery solutions to meet this need. Each of these solutions is fully calibrated so that users do not need to do any manual calibration of the system to take into account any losses due to data pick-off being routed to the input of the clock recovery unit. Shown below is a clock recovery solutions selection guide with the key specifications for each solution to help you select the solution(s) most appropriate for your application. For more detailed information on these solutions, see the 80Cxx Optical Sampling Modules datasheet (for clock recovery options integrated into the 80C07B, 80C08D, or 80C11B ) or the appropriate clock recovery datasheets for stand-alone clock recovery modules or instruments. Note: The stand-alone clock recovery modules/instruments have electrical inputs and can be used to recover clocks from electrical signals as well as from the electrical data pick-off outputs from the 80CXX Series optical sampling modules. Note: Clock recovery is integrated into the optical module and controlled from the Trigger Setup menu of the 8000 Series oscilloscope. 6 There are specific reference receiver groupings supported for the 80C07B. See the 80Cxx Optical Module datasheet for detailed information. 7 There are specific reference receiver groupings supported for the 80C12B. See the 80Cxx Optical Module datasheet for detailed information. 8 The clock recovery trigger pick-off (Option CRTP) for the 80C10C can support trigger pick-off for data rates to >43 Gb/s. 9

10 Datasheet Integrated clock recovery options Characteristic 80C07B 80C08D Opt. CR1 Continuously Variable Rate Range (Gb/ s) Clock Recovery Sensitivity (dbm) 12 Standard rates supported 125, 155 Mb/s 622 Mb/s 1063 Mb/s 1250 Mb/s 2125 Mb/s 2488, 2500 Mb/s 80C08D Opt. CR2 80C08D Opt. CR4 80C11B Opt. CR1 80C11B Opt. CR2 80C11B Opt. CR3 80C11B Opt. CR4 Fixed Rates Fixed Rates Fixed Rates Fixed Rates Fixed Rates Fixed Rates Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Stand-alone (electrical) clock recovery modules/instruments Characteristic 80A05 Std A05 Opt. 10G 13 CR125A 14 CR175A 14 CR286A 14 Continuously Variable Rate Range (Gb/s) Clock Recovery Sensitivity (mv p-p ) 15 Adjustable Clock Recovery Loop Bandwidth and Peaking 16 Standard rates supported 12 Electrical clock recovery sensitivity is for differential input and varies with the input clock rate. See clock recovery datasheets for more information. 13 The clock recovery module plugs into one of the 8000 Series large module slots and is controlled from the Trigger Setup menu. 14 Stand-alone clock recovery instrument; controllable from the BERTScope clock recovery instrument control application, accessible from the App menu of the 8000 Series oscilloscope. 15 Electrical clock recovery sensitivity is for differential input and varies with the input clock rate. See clock recovery datasheets for more information. 16 For more information on clock recovery loop bandwidth and peaking, see clock recovery datasheets. 10

11 DSA8300 Digital Serial Analyzer Sampling Oscilloscope Characteristic 80A05 Std A05 Opt. 10G 13 CR125A 14 CR175A 14 CR286A , 155 Mb/s 622 Mb/s 1063 Mb/s 1250 Mb/s 2125 Mb/s 2488, 2500 Mb/s 2.66 Gb/s 3.125, Gb/s 4.25 Gb/s 5.00 Gb/s 6.14 Gb/s 7.37 Gb/s 8.5 Gb/s 9.95 Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s Gb/s High-performance electrical test solutions The DSA8300 is also well-suited for a variety of high-performance electrical applications. With the modular system, users can configure their DSA8300 with a variety of electrical modules that are best suited to their requirements. the following table provides key specifications for the current electrical sampling modules available for use with the DSA8300, to help you select the electrical module(s) most appropriate for your application. Detailed specifications are available in the 80E00 Electrical Sampling Modules datasheet. Electrical sampling module selection guide Characteristic 80E01 80E03 80E07B 80E09B 80E11, 80E11X1 80E04 (TDR Module) Channels (80E11) 1 (80E11X1) Bandwidth 50 GHz 20 GHz 20/30 GHz (user selectable) Step response at full bandwidth (10-90%) 30/40/60 GHz (user selectable) 40/60/70 GHz (user selectable) 80E08B (TDR Module) GHz 20/30 GHz (user selectable) 7 ps 17.5 ps 11.7 ps 5.8 ps 5.0 ps 17.5 ps 11.7 ps 7 ps 80E10B (TDR Module) 30/40/50 GHz (user selectable) 13 The clock recovery module plugs into one of the 8000 Series large module slots and is controlled from the Trigger Setup menu. 14 Stand-alone clock recovery instrument; controllable from the BERTScope clock recovery instrument control application, accessible from the App menu of the 8000 Series oscilloscope. 11

12 Datasheet Characteristic 80E01 80E03 80E07B 80E09B 80E11, 80E11X1 80E04 (TDR Module) RMS Noise 1.8 mv 600 μv 280 μv at 20 GHz 300 μv at 30 GHz Incident TDR Step Rise Time (10-90%) Reflected TDR Step Rise Time (10-90%) Remote Sampling Capability 300 μv at 30 GHz 330 μv at 40 GHz 450 μv at 60 GHz 330 μv at 40 GHz 450 μv at 60 GHz 950 μv at 70 GHz 80E08B (TDR Module) 600 μv 280 μv at 20 GHz 300 μv at 30 GHz ps 18 ps 12 ps ps 20 ps 15 ps w/ optional 80X01 or 80X02 extender cable w/ optional 80X01 or 80X02 extender cable Fully integrated 2 m remote cable Fully integrated 2 m remote cable w/ optional 80X01 or 80X02 extender cable w/ optional 80X01 or 80X02 extender cable Fully integrated 2 m remote cable 80E10B (TDR Module) 300 μv at 30 GHz 370 μv at 40 GHz 600 μv at 50 GHz Fully integrated 2 m remote cable S-parameter performance characteristics (80E10B) All measurements were performed after proper warm up as specified in the DSA8300 manual Standard S-parameter dynamic range measurement practices were used to determine the dynamic range of the module Uncertainty results were derived from a wide range of devices, with 250 averages Better dynamic range can be achieved by selecting lower bandwidth settings on the 80E10B module due to a lower RMS noise floor Results apply to single-ended or differential measurements 80E10B dynamic range 12

13 DSA8300 Digital Serial Analyzer Sampling Oscilloscope 80E10B uncertainty Test solutions for 100 Gb/s (4 x 25 Gb/s) electrical standards With the continued increase in high-bandwidth applications, the need to test electrical components, modules and systems at high data rates is proliferating. An example of such data rates is the CEI 3.0 VSR-28 interface. This interface transfers data over multiple electrical channel at rates up to 28.6 Gb/s. Such signals place significant performance challenges on the test and measurement equipment used to acquire and analyze the devices under test. Some of these challenges include: The need to acquire the signal with excellent signal fidelity - this requirement has several implications for the test instrumentation: Low instrumentation noise Low instrumentation jitter The need to acquire the signal as close to the DUT as possible - thereby reducing signal degradation and potential inter-symbol interference The need to recover the clock from the data stream to acquire signals under test and to do detailed analysis of these signals. The DSA8300 with its modular architecture, and its associated modules and accessories, provides all of the components necessary to fully test multi-lane high bit-rate signals. To simplify configuring a system to test such devices, Tektronix offers the following product bundle: 80B28G - a DSA8300 product bundle for 28 Gb/s applications This bundle, when used with a DSA8300, provides all of the electrical sampling modules, accessories, and clock recovery capabilities needed to test applications at rates from 10 Gb/s to 28.6 Gb/s per lane. The bundle includes the following products: 1 ea. 80E09B: dual channel, 70 GHz Remote Electrical Sampling Module 1 ea. 82A04B: Phase Reference Module that supports sub-100 fs instrumentation jitter when used with the 80E09B 1 ea. CR286A: 28.6 GHz clock recovery instrument that supports clock recovery at rates from 150 Mb/s to 28.6 Gb/s 1 ea. 80X01: 1-meter sampling module extender cable used to extend the phase reference module to connect directly to the clock recovery module 1 ea. 80A08 : accessory kit with all of the necessary cables, adapters, DC blocks and other accessories to configure a complete test solution To extend this solution to test additional lanes in a multi-lane application, simply install additional 80E09B dual channel remote sampling modules. 13

14 Datasheet Specifications Product specifications and descriptions in this document are subject to change without notice. Vertical system Rise Time / Bandwidth Vertical Resolution Determined by the sampling modules used 16 bits over the sampling modules' dynamic range Electrical Resolution: <20 μv LSB (for 1 V full range) Optical resolution depends on the dynamic range of the optical module ranges from <20 nw for the 80C07B (1 mw full range) to <0.6 μw for the 80C10C (30 mw full range) Horizontal system Main and Magnification View Time Bases, Horizontal Scale 100 fs/div to 1 ms/div, in sequence or 100 fs increments Time Interval Accuracy Trigger Direct (Front Panel) Input Clock Input/Prescale Trigger (Front Panel), Eye or Pattern Mode Clock Input/Prescale Trigger (Front Panel), Other Mode TDR Clock Trigger (Lock to External 10 MHz Clock) Random Phase Corrected Mode (Clock Input to 82A04B) Triggered Phase Corrected Mode (Clock Input to 82A04B) Horizontal Deskew Range Available DSA8300 Record Length Longer Records Available Horizontal scale >20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 0.1% of interval, STDEV: 1 ps Horizontal scale 20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 1 ps + 0.5% of interval Mean accuracy determined by clock input accuracy STDEV: <0.7 ps (max); <0.1 ps (typical) Horizontal scale >20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 0.1% of interval, STDEV: 3 ps Horizontal scale 20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 1 ps + 0.5% of interval Horizontal scale >20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 0.01% of interval, STDEV: 1 ps (0.1 ps typical) Maximum timing deviation 0.1% of phase reference signal period, typical, relative to phase reference signal For more information on phase reference modes of operation, see the Phase Reference Module for the DSA8300 Sampling Oscilloscope datasheet. Maximum timing deviation relative to phase reference signal: >40 ns after trigger event: 0.2% of phase reference signal period, typical 40 ns after trigger event: 0.4% of phase reference signal period, typical 500 ps to +100 ns on any individual channel in 100 fs increments Mainframe slot deskew only: the 80E07B, 80E08B, 80E09B, 80E10B, 80E11, and 80E11X1 remote sampling modules include additional channel deskew range. 50, 100, 250, 500, 1000, 2000, 4000, 8000, or samples (magnification views have maximum record length of 4000 samples) IConnect : 1M samples 80SJNB Jitter, Noise, and BER Analysis Software: 10M samples (100k unit intervals, 100 samples per unit interval) 14

15 DSA8300 Digital Serial Analyzer Sampling Oscilloscope Trigger system Trigger Sources Clock Input / Prescale Trigger Input Clock Input Sensitivity Minimum Slew Rate Clock Input Range Pattern Lengths Supported (for Pattern Triggering with ADVTRIG Option) Clock Input Jitter in Clock-eye and Clock-pattern Trigger Modes (Typical) Clock Input Jitter in Clock-eye and Clock-pattern Trigger Modes (Max) TDR Trigger TDR Step Rate TDR Trigger Jitter Phase Reference Time Base Phase Reference Input Range Phase Reference Input Sensitivity Jitter Trigger Direct Input Trigger Sensitivity Trigger Level Range Trigger Input Range Clock Input/Prescale Trigger (front panel) TDR clock (generated internally) Clock recovery triggers from Optical Sampling modules and Electrical Clock Recovery modules (internally connected) Phase Reference (when using the 82A04B Phase Reference module) time base supports acquisitions without a trigger signal in its Free Run mode Trigger Direct Input (front panel) 100 mv p-p, 0.15 to 20 GHz (typical) 200 mv p-p, 0.15 to 15 GHz (guaranteed) 2 V/ns 1.0 V p-p (max) AC coupled 2 to 2 23 (8,388,608) inclusive GHz: 900 fs (RMS) GHz: 800 fs GHz: 425 fs GHz: 900 fs (RMS) GHz: 500 fs GHz: 600 fs Selectable from 25 to 200 khz in 1 khz steps Actual TDR step rate may vary up to 2% from requested rate 1.3 ps RMS (typical) 1.8 ps RMS (max) Standard 82A04B: 8-32 GHz (guaranteed), 2-32 GHz (typical) 82A04B Option 60G: 8-60 GHz (guaranteed), 2-70 GHz (typical) For clock frequencies <8 GHz, it may be necessary to filter the clock input to eliminate harmonics from the clock signal (see accessories xx, xx, and xx) Best jitter performance is with the clock input to the 82A04B in the following range: V. The phase reference time base remains operational to 100 mv (typical) with increased jitter f 8 GHz: 100 fs RMS, on a 10 GHz or faster sampling module 2 GHz f 8 GHz: 140 fs RMS, typical on a 10 GHz or faster acquisition module For clock frequencies <8 GHz, it may be necessary to filter the clock input to eliminate harmonics from the clock signal (see accessories xx, xx, and xx) 50 mv, DC - 4 GHz (typical) 100 mv, DC - 3 GHz (guaranteed) ±1.0 V ±1.5 V 15

16 Datasheet Trigger system Trigger Holdoff Trigger Direct Input Jitter Adjustable 5 μs to 50 ms in 0.5 ns increments 1.1 ps RMS + 5 ppm of horizontal position (typical) 1.5 ps RMS + 10 ppm of horizontal position (max) Acquisition system Acquisition modes Number of sampling modules accommodated Number of simultaneously acquired inputs Maximum acquisition rate Sample (Normal), Envelope, and Average Up to 4 dual-channel electrical; up to 2 optical sampling modules. Population of the CH1/CH2 large slot with any module other than one requiring power only displaces functionality of the CH1/CH2 small slot; population of the CH3/CH4 large slot with any module other than one requiring power only displaces functionality of the CH3/CH4 small slot. 8 channels maximum 300 ks/s per channel in TDR mode 200 ks/s per channel in all other nonphase reference modes 120 ks/s per channel in phase reference modes Waveform measurements System Measurement Rate Measurement Set Amplitude Measurements Timing Measurements Area Measurements Cursors Waveform Processing Mask Testing The DSA8300 supports up to 8 simultaneous measurements, updated 3 times per second with optional display of permeasurement statistics (min, max, mean, and standard deviation) Over 120 automated measurements include RZ, NRZ, and pulse signal types, and the following measurement types: High, Low, Amplitude, Peak-to-Peak, Max, Mid, Min, Mean, +Overshoot, Overshoot, P-P, Average Optical Power (dbm, watts), Noise, RMS Noise, SNR, Eye Height, Eye Opening Factor, Extinction Ratio (Ratio, %, db), Suppression Ratio (Ratio, %, db), OMA, Q-factor, RMS, AC RMS, Cycle RMS, Cycle Mean, Gain, Crossing %, Crossing Level Rise, Fall, Period, Bit Rate, Bit Time, Frequency, Crossing Time, +Cross, Cross, Jitter (P-P, RMS), Eye Width, +Width, Width, Burst Width, +Duty Cycle, Duty Cycle, Duty Cycle Distortion, Delay, Phase, Pulse Symmetry Area, Cycle Area Dot, vertical bar, and horizontal bar cursors Up to 8 math waveforms can be defined and displayed using the following math functions: Add, Subtract, Multiply, Divide, Average, Differentiate, Exponential, Integrate, Natural Log, Log, Magnitude, Min, Max, Square Root, and Filter. In addition, measurement values can be utilized as scalars in math waveform definitions For many applications, standard masks are available as predefined, built-in masks. Many of the most commonly used standard masks are shown in the following supported standards list. Contact your local Tektronix representative to get a list of all available masks. Unless otherwise noted, file-based masks are used to distribute new, Tektronix factory-created, updated masks as a file loadable by the firmware. User-defined masks allow the user to create (through UI or PI) user masks 16

17 DSA8300 Digital Serial Analyzer Sampling Oscilloscope Waveform measurements Supported standards Type Standard Ethernet SONET/SDH Fibre Channel Optical Fibre Channel Electrical SATA 100BASE-LX Mb/s 100BASE-BX Mb/s Gigabit Ethernet Gb/s 1000BASE-KX Gb/s 2 GBE Gb/s 10GBASE-X Gb/s 10GBASE-W Gb/s 10GBASE-R Gb/s FEC Gb/s 10GBASE-LRM Gb/s 40GBASE-FR Gb/s 40GBASE-LR Gb/s 40GBASE-SR Gb/s 100GBASE-ER Gb/s 100GBASE-LR Gb/s 100GBASE-SR Gb/s 100GBASE-SR Gb/s OC-1/STM Mb/s OC-3/STM Mb/s OC-12/STM Mb/s OC-48/STM Gb/s FEC Gb/s OC-192/STM Gb/s FEC Gb/s FEC Gb/s OTU Gb/s OC-768/STM Gb/s FEC Gb/s FEC Gb/s FC Mb/s FC Mb/s FC Mb/s FC Gb/s FC Gb/s FC Gb/s 8GFC Gb/s 10GFC Gb/s FC Gb/s 16GFC MM r Gb/s 16GFC SM r Gb/s 32GFC Gb/s FC Mb/s FC Mb/s FC Mb/s FC Gb/s FC2125E Gb/s: Abs, Beta, Tx/Rx; Abs, Gamma, Tx/Rx FC4250E Gb/s: Abs, Beta, Tx/Rx; Abs, Gamma, Tx/Rx FC8500E Gb/s: Abs, Beta, Tx/Rx; Abs, Gamma, Tx/Rx G Gb/s Tx, Rx G Gb/s Tx, Rx G Gb/s Tx, Rx 17

18 Datasheet Display system Touch Screen Display Colors Video Resolution Magnification Views 264 mm / 10.4 in. diagonal, color, LCD 16,777,216 (24 bits) 1024 horizontal by 768 vertical displayed pixels In addition to the main time base, the DSA8300 supports two magnification views. These magnifications are independently acquired using separate time-base settings which allow same or faster time/div than that of the main time base Input output ports Front Panel USB 2.0 Port(s) Anti-static Connection Trigger Direct Input Clock Input / Prescale Trigger TDR Clock Output DC Calibration Output Rear Panel USB Ports LAN Port Serial Ports GPIB DVI-I Video Port PS2 Serial Ports Audio Ports One USB 2.0 connector (instruments shipped after 12/2012 have 3 USB ports on the front panel) Banana-jack connector, 1 MΩ See Trigger System specification See Trigger System specification See Trigger System specification ±1.25 V maximum 4 USB 2.0 connectors RJ-45 connector, supports 10/100/1000BASE-T DB-9 COM1, COM2 ports IEEE488.2 connector DVI connector, female Connect to show the oscilloscope display, including live waveforms on an external monitor or projector. The primary Windows desktop can also be displayed on an external monitor using these ports. Alternatively, the DVI-I port can be configured to show the secondary Windows desktop (also called extended desktop or dualmonitor display). DVI to VGA 15-pin D-sub connector adapter provided Mouse and keyboard inputs 1/8 in. microphone input and line output Data storage Waveform Databases Hard Disk Drive Optical Drive Nonvolitile storage 4 independently accumulated waveform records of up to 4M waveform points each. Variable waveform database mode with true first-in/first-out of up to 2000 waveforms available on each of 4 waveform databases (2M samples maximum / waveform database) Rear-panel, removable hard disk drive, 500 GB capacity Front-panel DVD Read Only / CD Read-Write drive with CD-creation software application USB 2.0 flash memory 18

19 DSA8300 Digital Serial Analyzer Sampling Oscilloscope Power source Line voltage and frequency Power Consumption 90 V to 250 V 50 Hz to 400 Hz 205 W, typical, mainframe only 330 W, typical, fully loaded 600 W, maximum Physical characteristics Dimensions mm Inches Width Height Depth kg Weight lb EMC, environment and safety Temperature Operating +10 to +40 C Nonoperating 22 to +60 C Altitude Operating Nonoperating Relative Humidity Operating (CD-ROM not installed) Electromagnetic compatibility Safety 3,048 m (10,000 ft.) 12,190 m (40,000 ft.) 20% to 80% at or below 40 C (upper limit de-rates to 45% relative humidity at 40 C) 2004/108/EC UL3111-1, CSA1010.1, EN , IEC