BEAM MOVING HEAD YODN Lamp. 132W 2R MOVING HEAD Brightness / Stability USER MANUAL. Version 1.0 beta

Transcription

1 BEAM MOVING HEAD YODN Lamp W R MOVING HEAD Brightness / Stability This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. USER MANUAL Version.0 beta

2 TECHNICAL DATA POWER SUPPLIES Input Voltage: AC00-0V 0-60Hz Power Consumption: 00W LAMP SOURCE Professional Lamp Source - Type: YODN MSDR - Lamp Wattage: W - Lumen Output:,00 Lm - Colour temperature: 8,000K±00K - Average Lamp Life: 6000 hrs COLOR SYSTEM color wheel with colors + open EFFECTS SECTION gobo wheel with xed gobos + open Electronic Focus High speed shake effect -facet rotating prism Mechanical shutter and adjustable speed strobe effect Mechanical dimmer CONTROL AND PROGRAMMING Max DMX control channels DMX protocol signal: USITT DMX Display: LCD Display Pan/Tilt Resolution: 6 bit DMX signal connection: pole XLR input and output BODY Aluminium structure with die-cast plastic cover. Two side handles for transportation. Device locking PAN and TILT mechanisms for transportation and maintenance. MOVING BODY Travel: PAN = 0 TILT = 70 CONTROL MODE DMX/Master-slave/Auto COOLING SYSTEM Convective Fan Inside NET WEIGHT Kg GROSS WEIGHT Kg Packing Size 9 x 0 x (cm) SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP0. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids. DO NOT mount the projector directly onto in ammable surface The projector is only intended for installation, operation and maintenance by quali ed personnel. The projector must be installed in a location with adequate ventilation, at least 0cm from adjacent wall surfaces. Be sure that no ventilation slots are blocked. Do not project the beam onto in ammable surfaces, minimum distance is m Avoid direct exposure to the light from the lamp. The light is harmful to the eye. Do not attempt to dismantle and/or modify the projector in any way. Electrical connection must only be carried out by quali ed personnel. Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector. It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards. Do not connect this device to any other types of dimmer apparatus. Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Keep a projector s optical system clean. Do not touch LED lens with bare hands. The projector should always be installed with a secondary safety xing. A safety cord is supplied for this; it should be attached as shown in installing the projector section. Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for example by cracks or deep scratches. LED lamps should be replaced if damaged or having reached life limit. Exterior surface temperatures of the luminaire after minutes operation is, when steady state is achieved 70, There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers removed. If you have any questions, don t hesitate to consult your dealer or manufacturer. m

3 Short Mode/Channel Standard Extended FUNCTION VALUE DESCRIPTION RotGobo Wheel 6~ ~7 8~ ~9 0~ 6~6 6~67 68~7 7~ ~ Shake from slow to fast : Gobo 7 Shake from slow to fast : Gobo 8 Shake from slow to fast : Gobo 9 Shake from slow to fast : Gobo 0 Shake from slow to fast : Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo Rotation from fast to slow Rotation from slow to fast DMX TERMINATOR In the Controller, at the last xture in the chain, the DMX output has to be connected with a DMX terminator. This preventselectrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 0Ω(ohm) resistor connected across pins and, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below. 0Ω DMX TERMINATOR CONNECTION Connect a 0Ω (OHM) resistor across pins and in an XLR plug and insert into the DMX out socket on the last unit in the chain. SETUP OPTIONS-PROJECTOR CONFIGURATION PIN PIN Prism 0~7 8~ Prism Excluded Prism Inserted 0~7 Position Indel 0-0 Angle Degree 8 9 Prism Rotation 8~90 9~9 Rotation from fast to slow Stop 9~ Rotation from slow to fast 9 0 Focus 0~ 0% - 00% FUNC DOWN UP ENTER 0 Function "Stay in a certain value for more than seconds" 0~ ~9 0~7 7~99 00~ ~9 0~7 7~99 Unused Reset: Effects Unused Reset: Pan Tilt Unused Reset: Complete Unused Lamp off 00~ Unused ~ Lamp on Projector con guration can be set conveniently via press button switch and LCD display. To browse or change its setup options, Press button ENTER to unlock panel. Menu will be displayed on the screen, each menu has it own sub-menu. Each menu has speci c function, Please refer to Operation Menu for details. Press button UP or DOWN if you want to browse or change through the various Setup s. Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to change values.(add or subtract) Press button FUNC, it will return to the upper menu one by one. TO SET THE DMX START ADDRESS Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller. The xture have DMX s. There are simple, standard and extended. For example standard has channels, so set the No. projector s address 00, No. projector s address 0, No. projector s address 0, No. projector s address 0 and so on. Launch the projector. Press button ENTER more than seconds to unlock panel. Press button ENTER to display DMX address. Press button UP or DOWN, you can set the address. Press button ENTER to con rm, which means the projector has saved the Start Address automatically, when powered on next time, it will display the value saved last time. Press button UP or DOWN to change values.(add or subtract) Press button FUNC, it will return to the upper menu one by one.

4 DMX PROTOCOL Level Level Level Level Short Mode/Channel Standard Extended 6 7 FUNCTION Pan Pan Fine Tilt Tilt Fine P/T Speed Dimmer Strobe VALUE 0~ 0~ 0~ 0~ 0~ 0~9 0~ 0~9 0~7 8~ 6~ DESCRIPTION 0% - 00% 0% - 00% 0% - 00% 0% - 00% Pan & Tilt Speed from fast to slow Closed Dimmer from 0% - 00% Closed Strobe from slow to fast Pulsation from slow to fast strobe Open Operation Mode Prism Rotation Focus DMX Mode Auto Mode Master Mode Prism.Rot = 000 Focus = 000 DMX Short Mode DMX Standard Mode DMX Extended Mode Select Program Program = x Select Program Program = x 0~9 0~ White Color Slave SYNC Mode Select Program Program = x 6~ ~7 Color + Color Color Slave SAME Mode 6 8 Color Wheel 8~ ~9 0~ 6~ ~7 8~6 6~69 70~7 76~8 8~87 88~9 Color + Color Color Color + Color Color Color + Color Color Color + Color 6 Color 6 Color 6 + Color 7 Color 7 Color 7 + Color 8 Settings Pan Tilt Swap Pan Invert Tilt Invert Pan Tilt Swap =OFF Pan Tilt Swap =ON Pan Invert =OFF Pan Invert =ON Tilt Invert =OFF Tilt Invert =ON 9~99 00~0 Color 8 Color 8 + Color 9 Lamp on by power Lamp on by power =Disable 06~ Color 9 Lamp on by power =Enable 0 7

5 Level Level Level Level Level Level Level Level Wheel Shortcut Wheel Shortcut =OFF Frost Frost = +000 Wheel Shortcut =ON Focus Focus = +000 Display Setup Display Setup Delay Off Delay Off = Disable Information Temperature Temperature =0C Delay Off = Enable Fixture Hours Fixture Hours =00000 H Reset Hours =NO Display Setup Display Invert Display Invert = OFF Reset Hours =YES Display Invert = ON Product ID Product ID = Y************ Display Setup Language Language = English View DMX Value View DMX Value Channel 00 = 000 Language = 简体中文 Version Version =.00F Lost DMX Lost DMX =Clear Value Lamp Manual Control Lamp Status Control = DMX Status = Hot Lost DMX =Hold Value Turn Lamp On Advanced Access Code Access Code Code = 000 注 :Code = 008 Turn Lamp Off LED Pan Pan = +000 Load Defaults Load Defaults =NO Tilt Tilt = +000 Load Defaults =YES Dimmer Color Wheel Fixed Gobo Wheel Prism Dimmer = +000 Color Wheel = +000 Fixed Gobo = +000 Prism = +000 Note: There is only one Projector to be set as a Master in a signal Cable. If Master s functions used, Please disable DMX control signal. When multiple projectors work together in synchronous control state, Parameters can be transmitted from the master projector to the slave projectors such as DMX channel, Display setting status and operation (User memory data is included). Before parameters transmitted, the projector which will send parameters should be set as a Master and others be as Slaves. 8 9

6 OPERATION MENU Level R W Beam DMX Address = 00 R W Beam Auto = P0:S0 R W Beam Master = P0:S0 R W Beam Slave = P0:S0 R W Beam Slave same Address Setup Reset Level Level Level Address Setup Address = 00 Reset Effects Reset Pan & Tilt Reset Complete Pan Titl Dimmer Strobe Color Wheel Fixed Gobo Wheel Prism Pan = 000 Tilt = 000 Dimmer = 000 Strobe = 000 Color Wheel = 000 Fixed Gobo = 000 Prism = 000 Short Mode/Channel Standard Extended 6 8 FUNCTION VALUE DESCRIPTION Color Wheel ~7 8~ ~9 0~ 6~ ~7 8~ ~9 Color 0 Color 0 + Color Color Color + Color Color Color + Color Color 60~07 Color rotation from fast to slow 08~ 0~ 6~ ~7 8~ ~9 0~ 6~ ~7 8~ ~ Gobo Wheel 60~6 66~7 7~77 78~8 8~89 90~9 96~0 0~07 08~ ~9 0~ Color 9 + Color 0 Color rotation from slow to fast White (No Gobo) Gobo Gobo Gobo Gobo Gobo Gobo 6 Gobo 7 Gobo 8 Gobo 9 Gobo 0 Gobo Gobo Gobo Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo Shake from slow to fast : Gobo 6 6

7 POWER SUPPLY-MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off. IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards. MAINTENANCE To prolong a Projector s life, Regular maintenance should be done for its LED optical System to ensure that the system be in best operational condition. If the projector does not function, check the fuses on the power socket of the projector, if burned, they should only be replaced by fuses of the same speci cation. Should these be damaged call a quali ed technician before replacement. The projector has thermal protection device that will switch off the projector in case of overheating, should this occur, check if the fans work normally or fan and fan shield are blocked by dust. If the projector not operational, call a quali ed technician. After cleaned and repaired, the projector can be restarted. Any maintenance work should only be carried out by quali ed technicians. CONTROL CONNECTION KEEPING THE PROJECTOR CLEAN PIN PIN DMX OUT DMX OUT DMX IN DMX IN DMX PIN FUNCTION GND DATA- DATA+ DMX PIN FUNCTION GND DATA- DATA+ N/C N/C It de nitely necessary to keep a projector clean for its reliable use. Cooling fans and their shield should be cleaned every days. LED lamps lens and cover should be cleaned regularly for optimized light output. Cleaning frequency depends on how often a projector is used and its operational environment. A soft cloth and typical glass cleaning products should be used in cleaning. It is recommended to clean the external optics at least once every 0 days. Do not use any organic solvent, e.g. alcohol, to clean t housing of the apparatus. Connection between controller and projector and between one projector and another must be made with a core-screened cable, with each core having at least a 0.mm diameter. Connection to and from the projector is via cannon pin (which are included with the projector) or pin XLR plugs and sockets. The XLR's are connected as shown in the gure above. Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not connected in any way. The projector accepts digital control signals in protocol DMX (990). Connect the controller s output to the rst xture s input, and connect the rst xture s output to the second xture s input and connect the rest xtures in the same way. Eventually connect the last xture s output to a DMX terminator as shown in the gure below. TROUBLESHOOTING PROBLEM The projector can t be started ACTION > Power Cable not connected well > Power supply damaged or not connected well, a quali ed Technician should be required > Control board not connected well and a quali ed Technician should be The lamp can be started, but LED lampsare off and not controlled > LED boards not connected properly, a quali ed technician is needed A projector s lamps are on but it doesn t respond to the controller > Make sure that the projector s start address is correctly set > Replace or repair the DMX cable. 0 Ohms DMX The beam appears dim and its brightness slows sharply > Ambient temperature too high which result in a projector overheating, necessary ventilating measures needed. DMX-controller

8 BEAM MOVING HEAD W R YODN LAMP W R BEAM MOVING HEAD LIGHT DIMENSION FIGURE (mm) R-BEAM INDEX BEAM 0 00 SAFE USAGE OF THE PROJECTOR POWER SUPPLY-MAINS CONTROL CONNECTION DMX TERMINATOR SETUP OPTIONS-PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS OPERATION MENU DMX PROTOCOL MAINTENANCE KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA DIMENSION FIGURE