Table of Contents. Table of Contents...1 Usage Notice...2. Appendices Installation User Controls English

Transcription

1 Table of Contents Table of Contents...1 Usage Notice...2 Safety Information...2 Precautions...3 Eye Safety Warnings...5 Product Features...5 Introduction...6 Package Overview...6 Product Overview...7 Main Unit... 7 Input/Output Connections... 8 Remote Control... 9 Installation...10 Connecting the Projector...10 Connect to Computer/Notebook Connect to Video Sources Powering the projector On / Off...12 Powering On the Projector Powering off the projector Warning Indicator Adjusting the Projected Image...14 Adjusting the Projector s Height Adjusting the Projector s Zoom / Focus Adjusting Projection Image Size User Controls...17 Remote Control On-screen Display Menus...19 How to operate Menu Tree IMAGE IMAGE Advanced IMAGE Advanced Signal (RGB) DISPLAY DISPLAY 3D SETUP SETUP Security SETUP Audio Settings SETUP Advanced OPTIONS OPTIONS Advanced OPTIONS Lamp Settings OPTIONS Optional Filter Settings Appendices...41 Troubleshooting...41 Replacing the lamp...46 Compatibility Modes...48 Computer Compatibility Video Compatibility D input Compatibility RS232 Commands and Protocol Function List...51 RS232 Pin Assignments RS232 Protocol Function List Wall Mount Installation...55 Optoma Global Offices...56 Regulation & Safety Notices English

2 Usage Notice Safety Information The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. Class B emissions limits This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Important Safety Instruction 1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow. 2. Do not use the projector near water or moisture. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture. 3. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat. 4. Clean only with dry cloth. 5. Only use attachments/accessories specified by the manufacturer. 6. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to): Unit has been dropped. Power supply cord or plug has been damaged. Liquid has been spilled on to the projector. Projector has been exposed to rain or moisture. Something has fallen in the projector or something is loose inside. Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair. 7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock. 8. See projector enclosure for safety related markings. 9. The unit should only be repaired by appropriate service personnel. English 2

3 Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user s guide. Warning- Do not look into the projector s lens when the lamp is on. The bright light may hurt and damage your eyes. Warning- To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. Warning- Please do not open or disassemble the projector as this may cause electric shock. Warning- When replacing the lamp, please allow the unit to cool down. Follow instructions as described on pages Warning- This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. Warning- Reset the Lamp Reset function from the on-screen display OPTIONS Lamp Settings menu after replacing the lamp module (refer to page 39). When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under Replacing the Lamp section on pages Warning- When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to cool down. Warning- Do not use lens cap when projector is in operation. Warning- When the lamp is approaching the end of its lifetime, the message Lamp Warning: Lamp life exceeded. will show on the screen. Please contact your local reseller or service center to change the lamp as soon as possible. Warning- Do not look into or point the laser pointer on your remote control into your or someone s eyes. Laser pointer can cause permanent damage to eyesight. 3 English

4 Usage Notice Do: Turn off and unplug the power plug from the AC outlet before cleaning the product. Use a soft dry cloth with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Do not: Block the slots and openings on the unit provided for ventilation. Use abrasive cleaners, waxes or solvents to clean the unit. Use under the following conditions: - In extremely hot, cold or humid environments. Ensure that the ambient room temperature is within 5-40 C. Relative Humidity is 5-40 C, 80% (Max.), non-condensing. - In areas susceptible to excessive dust and dirt. - Near any appliance generating a strong magnetic field. - In direct sunlight. English 4

5 Eye Safety Warnings Usage Notice Avoid staring/facing directly into the projector beam at all times. Keep your back to the beam as much as possible. When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen. In order to minimize the lamp power, use room blinds to reduce ambient light levels. Product Features SVGA (800x600) / XGA (1024x768) / WXGA (1280X800) Native resolution HD compatible 720p and 1080p supported BrilliantColor TM Technology Kensington Lock RS232 control Rapid shutdown Full 3D (See page 50) The Product Features shall be configured by the manufacturer as per practical conditions. 5 English

6 Menu Introduction Package Overview Unpack and inspect the box contents to ensure all parts listed below are in the box. If something is missing, please contact your nearest customer service center. Projector Power Cord 1.8m Due to different applications in each Country, some regions may have different accessories. 2 AAA Batteries Documentation : User s Manual Warranty Card Quick Start Card WEEE Card (for EMEA only) IR Remote Control English 6

7 Product Overview Main Unit Introduction The interface is subject to model s specifications. 9 Do not block projector in/out air vents POWER button and LED indicator Ventilation (inlet) Zoom Ring Focus Ring Zoom Lens IR Receiver Ventilation (outlet) Input / Output Connections Power Socket 7 English

8 Introduction Input/Output Connections AUDIO-IN HDMI VGA- IN / SCART S-VIDEO VIDEO RS232 VGA-OUT AUDIO-OUT The interface is subject to model s specifications. 1. Power Socket 2. HDMI Connector 3. VGA-In/SCART Connector (PC Analog Signal/Component Video Input/HDTV/YPbPr/ SCART) 4. S-Video Input Connector 5. Composite Video Input Connector 6. RS-232 Connector (3-pin DIN Type) 7. VGA-Out Connector (Monitor Loop-through Output) 8. Audio Input connector (3.5mm mini jack) 9. Audio Output Connector (3.5mm Mini Jack) TM 10. Kensington Lock Port English 8

9 Introduction Remote Control The interface is subject to model s specifications Menu IR LED Indicator 2. Power On/Off 3. Source 4. Mouse Left Click 5. Enter 6. Four Directional Select Keys / Mouse control 7. Mouse on/off 8. Re-Sync 9. Mouse Right Click 10. Mode 11. Page Up 12. Volume +/- 13. Menu 14. Zoom 15. AV mute 16. Video 17. 3D 18. VGA 19. Page Down 20. Keystone +/- 21. Brightness 22. HDMI 23. S-Video 24. Eco+ 25. Numbered keypad (for password input) 26. Freeze 9 English

10 E62405SP R Installation Connecting the Projector Connect to Computer/Notebook Audio Output Due to the difference in applications for each country, some regions may have different accessories. HDMI VGA- IN / SCART S-VIDEO VIDEO RS232 VGA-OUT AUDIO-IN AUDIO-OUT 6 (*) Optional accessory The interface is subject to model s specifications. 1 7 Monitor Output 1...Power Cord 2...*DVI/HDMI Cable 3... *VGA Cable 4...*RS232 Cable 5...*Audio Input Cable 6...*Audio Output Cable 7...*VGA Out Cable English 10

11 E62405SP R Installation Connect to Video Sources DVD Player, Set-top Box, HDTV receiver Due to the difference in applications for each country, some regions may have different accessories. (*) Optional accessory The interface is subject to model s specifications. AUDIO-IN HDMI VGA- IN / SCART S-VIDEO VIDEO RS232 VGA-OUT AUDIO-OUT 8 9 S-Video Output Composite Video Output Audio Output Power Cord 2...*HDMI Cable 3...*3 RCA Component Cable 4...*15-Pin to 3 RCA Component/HDTV Adaptor 5... *SCART/VGA Adaptor 6... *VGA Cable 7...*Audio Input Cable 8... *S-Video Cable 9...*Composite Video Cable 10...*Audio Output Cable 11 English

12 Installation When Power mode (Standby) is set to Eco (<0.5W), the VGA output and Audio pass-through will be deactivated when the projector is in standby. Powering the projector On / Off Powering On the Projector 1. Securely connect the power cord and signal cable. When connected, the Power LED will turn Red. 2. Turn on the lamp by pressing POWER button either on the top of the projector or on the remote. The Power LED will now turn Blue. The startup screen will display in approximately 10 seconds. The first time you use the projector, you can select your preferred language from quick menu after the startup screen displays. 3. Turn on and connect the source that you want to display on the screen (computer, notebook, video player, etc). The projector will detect the source automatically. If not, push menu button and go to OPTIONS. Make sure that the Source Lock has been set to Off. If you connect multiple sources at the same time, press the SOURCE button or direct source keys on the remote control to switch between inputs. Power 1 Turn on the projector first and then select the signal sources. English 12

13 Installation Powering off the projector 1. Press the POWER button to turn off the projector lamp. The following message will be displayed on the screen. Press the POWER button again to confirm, otherwise the message will disappear after 15 seconds. When you press the POWER button a second time, the system will show the countdown timer on the screen. 2. The cooling fans continue to operate for about 10 seconds for cooling cycle. When the Power LED turns Red, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press POWER button to restart the projector. 3. Disconnect the power cord from the electrical outlet and the projector. 4. Do not turn on the projector immediately following a power off procedure. Warning Indicator When the POWER indicator flashes red (0.5 sec off, 0.5 sec on), the projector will automatically shut down. Please call the nearest Optoma facility for assistance. Contact the nearest service center if the projector displays these symptoms. See pages for more information. When the POWER indicator flashes red (1.0 sec off, 1.0 sec on), it indicates the projector has overheated. The projector will shut down automatically. Under normal conditions, the projector can be switched on again after it has cooled down. When the POWER indicator flashes red (0.5 sec off, 2.0 sec on), it indicates the fan has failed. 13 English

14 Installation Adjusting the Projected Image Adjusting the Projector s Height The projector is equipped with elevator feet for adjusting the image height. 1. Locate the adjustable foot you wish to modify on the underside of the projector. 2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the remaining feet as needed. Tilt-Adjustment Feet Tilt-Adjustment Ring English 14

15 Installation Adjusting the Projector s Zoom / Focus You may turn the zoom ring to zoom in or out. To focus the image, rotate the focus ring until the image is clear. SVGA/XGA series: The projector will focus at distances from 3.28 to 39.4 feet (1.0 to 12.0 meters). WXGA series: The projector will focus at distances from 3.28 to 39.4 feet (1.0 to 12.0 meters). Zoom Ring Focus Ring Adjusting Projection Image Size SVGA/XGA series: Projection Image Size from 22.9 to (0.58 to 7.62 meters). WXGA series: Projection Image Size from 27.2 to (0.69 to 7.65 meters). Top View Screen Screen (W) Projection Distance (D) Height Diagonal Screen Screen (H) Width Side View Offset (Hd) Projection Distance (D) 15 English

16 Installation SVGA/XGA Diagonal length (inch) size of 4:3 Screen Screen Size W x H Projection Distance (D) (m) (inch) (m) (feet) Offset (Hd) Width Height Width Height wide tele wide tele (m) (inch) WXGA Diagonal length (inch) size of 16:10 Screen Screen Size W x H This table is for user s reference only. Projection Distance (D) (m) (inch) (m) (feet) Offset (Hd) Width Height Width Height wide tele wide tele (m) (inch) English 16

17 Remote Control Using the Remote Control User Controls Menu The interface is subject to model s specifications. Power L Button R Button Page + Page - Enter Source Re-Sync Four Directional Select Keys PC/Mouse Control Keystone +/- Volume +/- Brightness 3D Menu HDMI Refer to the Power On/Off the Projector section on pages Mouse left click. Mouse right click. Use this button to page up. Use this button to page down. Confirm your item selection. Press Source to select an input signal. Automatically synchronizes the projector to the input source. Use to select items or make adjustments to your selection. Use for emulation of USB mouse via USB when you press Switch button. Adjust image distortion caused by tilting the projector. Adjust to increase / decrease the volume. Adjust the brightness of the image. Press the 3D to turn the 3D OSD menu on/off. Press Menu to launch the on-screen display (OSD) menu. To exit OSD, press Menu again. Press HDMI to choose HDMI source. 17 English

18 User Controls Using the Remote Control Menu AV mute: Save up to 70% of the lamp power when AV mute is applied. Freeze AV mute S-Video VGA Video Mouse on/off Mode Zoom Eco+ Press Freeze to pause the screen image. Press this button again to unlock. Momentarily turns off/on the audio and video. Press S-Video to choose S-Video source. Press VGA to choose VGA sources. Press Video to choose Composite video source. USB mouse switch. Select the display mode from Presentation, Bright, Movie, srgb, Blackboard, Classroom, User and 3D. Zoom in on an image. Press buttons to alter zoom. When Eco+ mode is activated, the brightness level of the content is automatically detected to significantly reduced lamp power consumption (up to 70%) during periods of inactivity. English 18

19 User Controls On-screen Display Menus The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press Menu on the Remote Control or Projector Keypad. 2 When OSD is displayed, use keys to select any item in the main menu. While making a selection on a particular page, press or Enter key to enter sub menu. 3. Use keys to select the desired item and adjust the settings using key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press Enter to confirm, and the screen will return to the main menu. 6. To exit, press MENU again. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu Settings 19 English

20 User Controls Menu Tree Main Menu Image Sub Menu Settings Display Mode Presentation / Bright / Movie / srgb / Blackboard / User / 3D Brightness -50~50 Contrast -50~50 Sharpness 1~15 #1 Color -50~50 #1 Tint -50~50 Advanced Gamma Film / Video / Graphics / Standard BrilliantColor 1~10 Color Temp. Color Settings Red / Green / Blue / Cyan / Magenta / Yellow / Warm / Medium / Cold Hue / Saturation / Gain White R / G / B Reset Exit Color Space AUTO / RGB / YUV #3 AUTO / RGB (0-255) / RGB (16-235) / YUV #2 Signal Automatic On / Off Display Reset Format Exit Phase (VGA) 0~31 Frequency (VGA) -5~5 H. Position (VGA) -5~5 V. Position (VGA) -5~5 Exit #4 4:3 / 16:9 / Native / AUTO #5 4:3 / 16:9 or 16:10 / Native / AUTO Edge Mask 0~10 Zoom -5~25 (80%~200%) Image Shift H Image Shift -100~100 V Image Shift -100~100 V Keystone -40~40 3D 3D Mode Off / DLP-Link / IR #6 3D Format Auto / SBS / Top and Bottom / Frame Sequential #6 3D Sync. Invert On / Off Setup Language Exit English / Deutsch / Français / Italiano / Español / Português / Svenska / Nederlands / Norsk/Dansk / Polski / Suomi / / / Magyar / eština / / / / / / / Türkçe / Vi t / Bahasa Indonesia / Român Projection Menu Location #5 Screen Type 16:10 / 16:9 English 20

21 User Controls Main Menu Sub Menu Settings Setup Options Security Security On / Off Security Timer Change Password Exit Projector ID 0~99 Audio Settings Internal Speaker On / Off Mute Month / Day / Hour On / Off Volume 0~10 Advanced Logo Default / Neutral Input Source Source Lock High Altitude Information Hide Test Pattern Background Color Closed Captioning Exit Off / CC1 / CC2 VGA / Video / S-Video / HDMI On / Off On / Off On / Off Advanced Direct Power On On / Off Lamp Settings Auto Power Off (min.) 0~180 Quick Resume None / Grid / White Pattern Black / Red / Blue / Green / White On / Off Sleep Timer (min.) 0~990 Power Mode (Standby) Exit Lamp Hours Lamp Reminder Brightness Mode Lamp Reset Exit Active / Eco On / Off Bright / Eco / Eco+ Yes / No Optional Filter #7 Optional Filter Installed Yes / No Settings Filter Usage Hours 0~9999 Filter Reminder Off / 300hr / 500hr / 800hr / 1000hr Filter Reset Yes / No Exit Reset Yes / No Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using. (#1) Color and Tint are only supported in Video mode. (#2) Signal is only supported in Analog VGA (RGB) signal. (#3) For HDMI Source only. (#4) For XGA model only. (#5) For WXGA model only. 16:9 or 16:10 depend on Screen Type setting. (#6) 3D Sync Invert is only available when 3D is enabled and this mode 3D is for DLP link glass only. (#7) Optional Filter Settings is not available for this model. 21 English

22 User Controls IMAGE Display Mode There are many factory presets optimized for various types of images. Presentation: Good color and brightness from PC input. Bright: Maximum brightness from PC input. Movie: For home theater. srgb: Standardised accurate color. Blackboard: This mode should be selected to achieve optimum color settings when projecting onto a blackboard (green). User: User s settings. 3D: Recommend setting for 3D mode enabled. Any further adjustments by the user in 3D will be saved in this mode for further use. Brightness Adjust the brightness of the image. Press the Press the Contrast to darken image. to lighten the image. The contrast controls the degree of difference between the lightest and darkest parts of the picture. Press the Press the to decrease the contrast. to increase the contrast. English 22

23 User Controls Color and Tint functions are only supported under Video mode. Sharpness Adjust the sharpness of the image. Press the Press the Color to decrease the sharpness. to increase the sharpness. Adjust a video image from black and white to fully saturated color. Press the Press the Tint to decrease the amount of saturation in the image. to increase the amount of saturation in the image. Adjust the color balance of red and green. Press the Press the to increase the amount of green in the image. to increase the amount of red in the image. 23 English

24 User Controls IMAGE Advanced Gamma This allows you to choose a degamma table that has been fine-tuned to bring out the best image quality for the input. Film: for home theater. Video: for video or TV source. Graphics: for image source. Standard: for PC or computer source. BrilliantColor This adjustable item utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing true, more vibrant colors in picture. The range is from 0 to 10. If you prefer a stronger enhanced image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting. Color Temp If set to cold temperature, the image looks more blue. (cold image) If set to warm temperature, the image looks more red. (warm image) Color Settings Press into the next menu as below and then use or to select item. English 24

25 User Controls Red/Green/Blue/Cyan/Magenta/Yellow: Use or to select Hue, Saturation and Gain Colors. White: Use or to select Red, Green and Blue Colors. Reset: Choose Yes to return the factory default settings for color adjustments. (*) For HDMI only. Color Space Select an appropriate color matrix type from AUTO, RGB, RGB(0-255) (*), RGB(16-235) (*) or YUV. Reset Choose Yes to return the display parameters on all menus to the factory default settings. 25 English

26 User Controls IMAGE Advanced Signal (RGB) Signal is only supported in Analog VGA (RGB) signal. Automatic Automatically selects the singal. If you use this function, the Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again. Phase Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers, use this function to correct it. Frequency Change the display data frequency to match the frequency of your computer s graphic card. Use this function only if the image appears to flicker vertically. H. Position Press the Press the to move the image left. to move the image right. V. Position Press the Press the to move the image down. to move the image up. English 26

27 User Controls DISPLAY Format Use this function to choose your desired aspect ratio. SVGA/XGA 4:3: This format is for 4 3 input sources. 16:9: This format is for 16 9 input sources, like HDTV and DVD enhanced for Wide screen TV. Native: This format displays the original image without any scaling. AUTO: Automatically selects the appropriate display format. Auto Input resolution Auto/Scale (SVGA) Auto/Scale (XGA) H V H V H V :3 Wide Laptop SDTV HDTV English

28 User Controls Aspect ratio (source detected) Resize image (SVGA) Resize image (XGA) 4:3 800 x 600 center 1024 x 768 center 16:9 800 x 450 center 1024 x 576 center Native No resize image, 1:1 mapping and centered. This format shows the original image without scaling. WXGA 16:9 or 16:10 depend on Screen Type setting. 4:3: This format is for 4 3 input sources. 16:9: This format is for 16 9 input sources, like HDTV and DVD enhanced for Wide screen TV. 16:10: This format is for input sources, like widescreen laptops. Native: This format displays the original image without any scaling. AUTO: Automatically selects the appropriate display format. Auto Input resolution Screen Type = 16:10 Screen Type = 16:9 Auto/Scale Auto/Scale H V H V H V :3 Wide Laptop SDTV HDTV English 28

29 User Controls 16:10 Screen 480i/p 576i/p 1080i/p 720p PC 4: x 800 center 16: x 800 center Native 1:1 mapping centered. 1:1 mapping (960 x 540) display 1280 x x 720 center 1:1 mapping centered. 16:9 Screen 480i/p 576i/p 1080i/p 720p PC 4:3 960 x 720 center Each I/O has different setting of Edge Mask. Edge Mask and Zoom can t work at same time. 16: x 720 center Native 1:1 mapping centered. 1:1 mapping (960 x 540) display 1280 x x 720 center 1:1 mapping centered. Edge Mask Edge mask function removes the noise in a video image. Edge mask the image to remove video encoding noise on the edge of video source. Zoom Press the Press the to reduce the size of an image. to magnify an image on the projection screen. Image Shift Press into the next menu as below and then use or to select item. H: Use or to shift the projected image position horizontally. V: Use or to Shift the projected image position vertically. V Keystone Press the or to adjust image distortion vertically. If the image looks trapezoidal, this option can help make the image rectangular. 29 English

30 User Controls DISPLAY 3D IR options may vary according to model. 3D Sync Invert is only available when 3D is enabled and this mode 3D is for DLP link glass only. Compatible 3D source, 3D content and active shutter glasses are required for 3D viewing. See page 50 for supported 3D formats. 3D Mode Off: Select Off to turn 3D settings off for 3D images. DLP Link: Select DLP Link to use optimized settings for DLP Link 3D images. IR: Select IR to use optimized settings for IR-based 3D images. 3D Format Auto : When a 3D identification signal is detected, the 3D format is selected automatically. SBS: Use this mode for Side-by-side format 3D content. Top and Bottom: Use this mode for Top and Bottom format 3D content. Frame Sequential: Use this mode for Frame Sequential format 3D content. 3D Sync. Invert Press the On to invert left and right frame contents. Press the Off for default frame contents. English 30

31 User Controls SETUP Language Choose the multilingual OSD menu. Press or into the sub menu and then use the or key to select your preferred language. Press Enter to finalize the selection. Projection Rear-Desktop and Rear-Ceiling are to be used with a translucent screen. Front-Desktop This is the default selection. The image is projected straight on the screen. Rear-Desktop When selected, the image will appear reversed. Front-Ceiling When selected, the image will turn upside down. Rear-Ceiling When selected, the image will appear reversed in upside down position. 31 English

32 User Controls Screen Type is for WXGA only. Menu Location Choose the menu location on the display screen. Screen Type Choose the screen type from16:10 or 16:9. Projector ID ID definition can be set up by menu (range 0-99), and allow user control an individual projector by RS232. Refer to page for the complete list of RS232 commands. English 32

33 User Controls SETUP Security Security On: Choose On to use security verification when the turning on the projector. Off: Choose Off to be able to switch on the projector without password verification. Password default value is 1234 (first time). Security Timer Use this function to set the how long (Month/Day/Hour) the projector can be used. Once this time has elapsed you will be requested to enter your password again. Change Password First time: 1. Press to set the password. 2. The password has to be 4 digits. 3. Use number button on the remote to enter your new password and then press key to confirm your password. Change Password: 1. Press to input old password. 2. Use number button to enter current password and then press to confirm. 3. Enter new password (4 digits in length) using the number buttons on the remote, then press to confirm. 4. Enter new password again and press to confirm. 33 English

34 User Controls If the incorrect password is entered 3 times, the projector will automatically shut down. If you have forgotten your password, please contact your local office for support. English 34

35 User Controls SETUP Audio Settings Internal Speaker Choose the On or Off to turn on or off the internal speaker. Mute Choose the On to turn mute on. Choose the Off to turn mute off. Volume Press the Press the to decrease the volume. to increase the volume. 35 English

36 User Controls SETUP Advanced Logo Press to capture an image of the picture currently displayed on screen. If changes are made they will take effect the next time the projector is powered on. Default: The default startup screen. Neutral: Logo is not displayed on startup screen. Closed Captioning Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered on. Off: select Off to turn off the closed captioning feature. CC1:CC1 language: American English. CC2:CC2 language (depending on the TV channel of the user):spanish, French, Portuguese, German, Danish. English 36

37 User Controls OPTIONS Input Source Use this option to enable / disable input sources. Press to enter the sub menu and select which sources you require. Press Enter to finalize the selection. The projector will not search for inputs that are not selected. Source Lock On: The projector will only search current input connection. Off: The projector will search for other signals if the current input signal is lost. High Altitude When On is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin. Information Hide On: Choose On to hide the info message. Off: Choose Off to show the searching message. Test Pattern Display a test pattern. There are Grid, White pattern and None. Background Color Use this feature to display a Black, Red, Blue, Green or White, screen when no signal is available. Reset Choose Yes to return the display parameters on all menus to the factory default settings. 37 English

38 User Controls OPTIONS Advanced Direct Power On Choose On to activate Direct Power mode. The projector will automatically power on when AC power is supplied, without pressing the key on the projector control panel or on the remote control. When Power mode (Standby) is set to Eco (<0.5W), the VGA output and Audio pass-through will be deactivated when the projector is in standby. Auto Power Off (min) Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes). Sleep Timer (min) Sets the countdown timer interval. The countdown timer will start, with or without a signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes). Quick Resume On: If the projector is accidentally turned off, this feature allows the projector to be instantly powered on again, if selected within a period of 100 seconds. Off: The fan will start cooling the system immediately when user turns off the projector. Power Mode (Standby) Eco.: Choose Eco. to save power dissipation further < 0.5W. Active: Choose Active to return to normal standby and the VGA out port will be enabled. English 38

39 User Controls OPTIONS Lamp Settings Lamp Hours Display the projection time. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement of lamp. When ambient temperature is over 40 C in operating, the projector will switch to Eco automatically. Brightness Mode Eco.: Choose Eco. to dim the projector lamp which will lower power consumption and extend the lamp life. BRIGHT: Choose BRIGHT to increase the brightness. Eco+: When Eco+ mode is activated, the brightness level of the content is automatically detected to significantly reduced lamp power consumption (up to 70%) during periods of inactivity. Lamp Reset Reset the lamp hour counter after replacing the lamp. 39 English

40 User Controls OPTIONS Optional Filter Settings Optional Filter Settings is not available for this model. Optional Filter Installed Select Yes to display warning message after 500 hours of use. Select No to turn off warning message. Filter Usage Hours Display the filter time. Filter Reminder Choose this function to show or hide the warning massage when the changing filter message is displayed. (Factory default setting: 500 hours) Filter Reset Reset the dust filter counter after replacing or cleaning the dust filter. English 40

41 Troubleshooting Appendices If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. No image appears on-screen Ensure all the cables and power connections are correctly and securely connected as described in the Installation section. Ensure all the pins of connectors are not bent or broken. Check if the projection lamp has been securely installed. Please refer to the Replacing the lamp section. Ensure that the AV mute feature is not turned on. Partial, scrolling or incorrectly displayed image Press Re-SYNC on the remote. If you are using a PC: For Windows 95, 98, 2000, XP, Windows 7: 1. Open the My Computer icon, the Control Panel folder, and then double click on the Display icon. 2. Select the Settings tab. 3. Verify that your display resolution setting is lower than or equal to UXGA ( ). 4. Click on the Advanced Properties button. If the projector is still not projecting the whole image, you will also need to change the monitor display you are using. Refer to the following steps. 5. Verify the resolution setting is lower than or equal to UXGA ( ). 6. Select the Change button under the Monitor tab. 41 English

42 Appendices 7. Click on Show all devices. Next, select Standard monitor types under the SP box; choose the resolution mode you need under the Models box. 8. Verify that the resolution setting of the monitor display is lower than or equal to UXGA ( ). If you are using a Notebook: 1. First, follow the steps above to adjust resolution of the computer. 2. Press the appropriate keys listed below for your notebook manufacturer to send signal out from notebook to projector. Example: [Fn]+[F4] Acer Asus Dell Gateway [Fn]+[F5] [Fn]+[F8] [Fn]+[F8] [Fn]+[F4] IBM/Lenovo HP/Compaq NEC Toshiba [Fn]+[F7] [Fn]+[F4] [Fn]+[F3] [Fn]+[F5] Mac Apple: System Preference Display Arrangement Mirror display If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector. The screen of the Notebook or PowerBook computer is not displaying your presentation If you are using a Notebook PC Some Notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer s manual for detailed information. Image is unstable or flickering Use Phase to correct it. See page 26 for more information. Change the monitor color setting on your computer. Image has vertical flickering bar Use Frequency to make an adjustment. See page 26 for more information. Check and re-configure the display mode of your graphic card to make it compatible with the projector. English 42

43 Appendices Image is out of focus Adjust the Focus Ring on the projector lens. Make sure the projection screen is between the required distance. See pages The image is stretched when displaying 16:9 DVD title When you play anamorphic DVD or 16:9 DVD, the projector will show the best image when the projector display mode is set to 16:9 in the OSD. If you play 4:3 format DVD titles, please change the format to 4:3 in the projector OSD. If the image is still stretched, you will also need to adjust the aspect ratio by referring to the following: Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player. Image is too small or too large Adjust the Zoom Ring on the top of the projector. Move the projector closer to or further from the screen. Press Menu button on the remote control, go to Display Format and try the different settings. Use of Keystone is not recommended. Image has slanted sides If possible, reposition the projector so that it is horizontally centered on the screen and below the bottom of the screen. Press Keystone +/- button on the remote control until the sides are vertical. Image is reversed Select SETUP Projection from the OSD and adjust the projection direction. 43 English

44 Appendices The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power. Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the Replacing the Lamp section on pages LED lighting message Message Standby State (Input power cord) Power on (Warming) Power LED (Red) Power LED (Blue) Flashing (0.5 sec off, 0.5 sec on) Lamp lighting Power off (Cooling) Flashing (1 sec off, 1 sec on) <10 sec to off Error (Over Temp.) Flashing (1 sec off, 1 sec on) Steady light No light Error (Fan fail) Error (Lamp fail) Flashing (0.5 sec off, 2.0 sec on) Flashing (0.5 sec off, 0.5 sec on) English 44

45 Appendices On Screen Messages Temperature warning: Fan failed: Lamp warning: Out of display range: If the remote control does not work Check the operating angle of the remote control is within ±15 both horizontally and vertically of one of the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (±0 ) of the projector. Make sure the batteries are inserted correctly. Replace batteries if they are exhausted. 45 English

46 Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must be used to prevent any loose parts from falling out of projector. Warning: Lamp compartment may be hot! Allow it to cool down before changing the lamp! Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. English 46

47 Appendices 1 The screws on the lamp cover and the lamp cannot be removed. The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the lamp module if it was accidentally touched Lamp Replacement Procedure: 1. Switch off the power to the projector by pressing the button. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the two screws on the cover Lift up and remove the cover Unscrew the two screws on the lamp module Lift up the lamp handle and remove the lamp module slowly and carefully. 4 To replace the lamp module, reverse the previous steps. 8. Turn on the projector and reset the lamp timer. Lamp Reset: (i) Press Menu (ii) Select OPTIONS (iii) Select Lamp Settings (iv) Select Lamp Reset (v) Select Yes. 47 English

48 Appendices Compatibility Modes Computer Compatibility Mode Resolution V-Sync (Hz) Anglog/Digital H-Sync (KHz) VGA VGA For widescreen resolution (WXGA), the compatibility support is dependent on Notebook/PC models. Please note that using resolutions other than native 800 x 600 (SVGA), 1024 x 768 (XGA model), 1280 x 800 (WXGA model) may result in some loss of image clarity. VGA VGA VGA VGA VGA VGA SVGA SVGA SVGA SVGA SVGA XGA XGA XGA XGA HD 1280 x HD 1280 x WXGA x SXGA 1280 x SXGA x UXGA English 48

49 Appendices Computer Compatibility (Mac) Resolution V.Frequency [Hz] Macbook Macbook Pro Power Mac G5 Power Mac G4 800x O O X X 800x O O O O 800x O O O O 800x O O O O 1024x O O O O 1024x O O O O 1024x O O O O 1024x O O O O 1280x O O O O 1280x O O X O 1280x O O X O 1280x O O X O 1280x O O O O 1280x O O X O 1280x O O O O 1280x X O O O 1280x X O O X 1680x X O O X Video Compatibility NTSC M (3.58MHz), 4.43 MHz PAL SECAM SDTV HDTV B, D, G, H, I, M, N B, D, G, K, K1, L 480i/p@60Hz, 576i/p@50Hz 720p@50Hz/60Hz, 1080i@50Hz/60Hz, 1080p@24Hz/25Hz/30Hz/50Hz/60Hz 49 English

50 Appendices 3D input Compatibility HDMI 1.4a 3D timing Formats Modes Resolution V.Frequency [Hz] H.Frequency [KHz] Pixel Rate [MHz] Frame Sequential Top and Bottom Side by Side (half) 720p 1280x p 1280x p 1920x p 1280x p 1280x p 1920x i 1920x (25) i 1920x (30) HDMI 1.3 3D timing Formats Modes Resolution V.Frequency [Hz] H.Frequency [KHz] Pixel Rate [MHz] Side by Side (half) Top and Bottom HQFS 720p 1280x p 1280x i 1920x (25) i 1920x (30) p 1280x p 1280x i 1920x (25) i 1920x (30) i 720x i 720x VGA 1.3 3D timing Formats Modes Resolution V.Frequency [Hz] H.Frequency [KHz] Pixel Rate [MHz] Frame Sequential Side by Side (half) or Top and Bottom SVGA 800x XGA 1024x p 1280x SVGA 800x XGA 1024x p 1280x Composite/S-Video Formats Modes Resolution V.Frequency [Hz] H.Frequency [KHz] Pixel Rate [MHz] HQFS NTSC 720x PAL 720x English 50

51 Appendices RS232 Commands and Protocol Function List RS232 Pin Assignments RS232 shell is grounded. Pin no. Spec. (from projector side) 1 TXD 2 RXD 3 GND 51 English

52 Appendices RS232 Protocol Function List 1. There is a <CR> after all ASCII commands. 2. 0D is the HEX code for <CR> in ASCII code. Baud Rate : 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F XX=00-99, projector's ID, XX=00 is for all projectors SEND to projector ASCII Code HEX Code Function Description ~XX00 1 7E D Power ON ~XX00 0 7E D Power OFF (0/2 for backward compatible) ~XX00 1 ~nnnn 7E a 0D Power ON with Password ~nnnn = ~0000 (a=7e ) ~9999 (a=7e ) ~XX01 1 7E D Resync ~XX02 1 7E D AV Mute On ~XX02 0 7E D Off (0/2 for backward compatible) ~XX03 1 7E D Mute On ~XX03 0 7E D Off (0/2 for backward compatible) ~XX04 1 7E D Freeze ~XX04 0 7E D Unfreeze (0/2 for backward compatible) ~XX05 1 7E D Zoom Plus ~XX06 1 7E D Zoom Minus ~XX12 5 7E D VGA ~XX12 7 7E D VGA SCART ~XX12 8 7E D VGA Component ~XX E D Video ~XX20 1 7E D Display Mode Presentation ~XX20 2 7E D Bright ~XX20 3 7E D Movie ~XX20 4 7E D srgb ~XX20 5 7E D User ~XX20 7 7E D Blackboard ~XX20 8 7E D 3D ~XX21 n 7E a 0D Brightness n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX22 n 7E a 0D Contrast n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX23 n 7E a 0D Sharpness n = 1 (a=31) ~ 15 (a=31 35) ~XX24 n 7E a 0D Color Settings Red Gain n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX25 n 7E a 0D Green Gain n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX26 n 7E a 0D Blue Gain n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX27 n 7E a 0D Red Bias n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX28 n 7E a 0D Green Bias n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX29 n 7E a 0D Blue Bias n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX30 n 7E a 0D Cyan n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX31 n 7E a 0D Yellow n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX32 n 7E a 0D Magenta n = -50 (a=2d 35 30) ~ 50 (a=35 30) ~XX33 1 7E D Reset ~XX34 n 7E a 0D BrilliantColorTM n = 1 (a=30) ~ 10 (a=31 30) ~XX35 1 7E D Gamma Film ~XX35 2 7E D Video ~XX35 3 7E D Graphics ~XX35 4 7E D Standard ~XX36 1 7E D Color Temp. Warm ~XX36 2 7E D Medium ~XX36 3 7E D Cold ~XX37 1 7E D Color Space Auto ~XX37 2 7E D RGB ~XX37 3 7E D YUV ~XX45 n 7E a 0D Color (Saturation) n = -50 (a=30) ~ 50 (a= ) ~XX44 n 7E a 0D Tint n = -50 (a=30) ~ 50 (a= ) English 52