BM-1 Bench Top Vibration Isolation Platform

Transcription

1 BM- Bench Top Vibration Weight: Approximately 8 lb (36 kg) Dimensions: 24 W x 22.5 D x 8.5 H (6mm W x 572mm D x 26mm H) Load Capacities (approximate): BM- 5BM- 25BM- 35BM- 5BM- 65BM- 6-5 lb (27-48 kg) 9-55 lb (4-7 kg) 8-27 lb (82-23 kg) lb (32-68 kg) lb ( kg) 5-68 lb ( kg) Vertical natural frequency of /2 Hz or less can be achieved over the entire load range. Horizontal natural frequency is load dependent. /2 Hz or less can be achieved at or near the upper limits of the payload range. ) Vertical Load Adjustment Crank Simple manual adjustment compensates for changes in vertical load. 2) Vertical Position Indicator Easily determine optimum setting using this simple visual indicator. 3) Vertical Stiffness Adjustment Screw Dial in Guaranteed /2 Hz or less Vertical natural frequency using this simple adjustment. Our highest capacity bench top isolator. A cost effective product for weight loads up to 68 lb and /2 Hz performance vertical and horizontal. The curve below shows the typical vertical /2 Hz performance of the BM-. It offers - times performance than typical high-performance air tables. Typical Curve: BM- Vertical 3.5 Hz mHz Hz 3/7 46 S. Hindry Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright 9 Minus K Technology, Inc. All rights reserved.

2 BM-4 Bench Top Vibration Weight: Approximately 6 lb (27 kg) Dimensions: 6.8 W x 6.8 D x 8.5 H (427mm W x 427mm D x 26mm H) Approximate payload weight range: 25BM-4 5BM-4 BM-4-25 lb ( - kg) - 55 lb (9-25 kg) 5-5 lb (23-48 kg) The most cost effective bench top platform capable of /2 Hz performance vertical and horizontal. Vertical natural frequency of /2 Hz or less can be achieved over the entire load range. Horizontal natural frequency is load dependent. /2 Hz or less can be achieved at or near the upper limits of the payload range. The curve below shows the typical vertical /2 Hz performance of the BM-4. It offers - times performance than typical high-performance air tables. Typical Curve: 3 BM-4 Vertical.5 Hz mHz Hz 3/7 46 S. Hindry Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright 9 Minus K Technology, Inc. All rights reserved.

3 BM-6 Bench Top Vibration Weight: Approximately 35 lb (6 kg) Dimensions: 8 W x D x 4.6 H (457mm W x 58mm D x 7mm H) Approximate payload weight range: 25BM-6 5BM-6 BM-6-3 lb (4.5-4 kg) lb ( - 25 kg) 5-5 lb (23-48 kg) Vertical and horizontal frequencies are weight dependent. Vertical frequency of 2.5 Hz and horizontal frequency of.5 Hz are achieved at or near the upper limits of the payload range. At the lower limits of the payload range, the vertical frequency is approximately 3.4 Hz and the horizontal frequency is approximately 2.5 Hz. Typical Curves:... BM-6 VERTICAL db -4-6 The new BM-6 bench top platform offers performance than a full size air table in a package only 4.6 inches tall, and without air! This new vibration isolation platform reaches a new price point and is extremely easy to use. It offers a.5 Hz horizontal natural frequency and a 2.5 Hz vertical natural frequency. There is only one adjustment. There is no need for air or electricity. This is the thinnest, most portable, and most userfriendly isolator ever offered at this level of performance per dollar. The curves below demonstrate the -than-air performance that the BM-6 delivers. Vertically, the BM-6 offers a resonant frequency that is comparable to or than most air tables. Horizontally, the BM-6 offers much performance than typical air tables, which can have horizontal frequencies as high as 4-5 Hz.... BM-6 HORIZONTAL db S. Hindry Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright 9 Minus K Technology, Inc. All rights reserved. 3/7

4 BM-8 Bench Top Vibration Weight: Approximately 4 lb (6 kg)... Dimensions: 8 W x D x 4.6 H (457mm W x 58mm D x 7mm H) Approximate payload weight range: 25BM-8 5BM-8 BM-8 25BM-8 5BM-8 75BM-8* BM-8* 225BM-8* 25BM-8* - 3 lb (4.5-4 kg) *Weight: Approximately 47 lb. (2 kg) / (same dimensions) Horizontal frequencies are weight dependent. Horizontal frequency of.5 Hz is achieved at or near the upper limits of the payload range. At the lower limits of the payload range the horizontal frequency is approximately 2.5 Hz. Vertical frequency is tunable to.5 Hz throughout the payload range. Typical Curves: BM-8 VERTICAL lb ( - 25 kg) 5-5 lb (23-48 kg) 9-3 lb (4-59 kg) lb (57-7 kg) 5-8 lb ( kg) 75-5 lb ( kg) - 23 lb (9.5-4 kg) lb (2-5.5 kg) db -4-6 The BM-8 bench top platform offers - times performance than a full size air table in a package only 4.6 inches tall, and without air or electricity! This vibration isolation platform is extremely easy to use and offers extreme performance. It offers a.5 Hz horizontal natural frequency and our signature.5 Hz vertical natural frequency. There are only two adjustments. This is the thinnest, most portable, and most userfriendly isolator ever offered that is capable of delivering this level of performance. The verticle curve below demonstrates the vertical /2 Hz performance of the BM-8. The BM-8 delivers the high performance of our larger isolators in a package only 4.6 inches tall. Horizontally, the BM-8 offers natual frequencies as low as.5 Hz, much than typical air tables.... Any BM-8 can be made 6 W x D (47mm W x 58mm D) for an additional $5. BM-8 HORIZONTAL db -4-6 / 46 S. Hindry Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright 9 Minus K Technology, Inc. All rights reserved.

5 BM- Bench Top Vibration Weight: Approximately 35 lb (6 kg) Dimensions: 2.2 W x 2.2 D x 4.6 H (3mm W x 3mm D x 7mm H) Approximate payload weight range: BM- 25BM- 5BM- 75BM- BM- - lb ( kg) - 3 lb (4.5-4 kg) 3-55 lb (4-25 kg) 5-8 lb ( kg) 75 - lb (34-5 kg) Horizontal frequencies are weight dependent. Horizontal frequency of.5 Hz is achieved at or near the upper limits of the payload range. At the lower limits of the payload range the horizontal frequency is approximately 2.5 Hz. Vertical frequency is tunable to.5 Hz throughout the payload range. The BM- bench top platform offers - times performance than a full size air table in a package only 4.6 inches tall and 2 inches wide and deep. It also does this without any air or electricity! This vibration isolation platform is extremely easy to use and offers extreme performance. It offers a.5 Hz horizontal natural frequency and our signature.5 Hz vertical natural frequency. There are only two adjustments. The BM- is perfect for new generations of small SPM s that require the highest performance in a very compact system. This is the thinnest, smallest footprint, most portable, and most user-friendly isolator ever offered that is capable of delivering this level of performance. Typical Curves: The vertical curve below demonstrates the vertical /2 Hz performance of the BM-. Horizontally, the BM- offers natual frequencies as low as.5 Hz, much than typical air tables. BM- VERTICAL BM- HORIZONTAL... - db db / 46 S. Hindy Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright 9 Minus K Technology, Inc. All rights reserved.

6 CM- Low Frequency Vibration Isolator Weight: Approximately 26 lbs (.8 kg) Dimensions: 7.875" W x 7.875" D x 8.5" H (mm W x mm D x 26mm H) Load Capacities (approximate): CM- 5CM- 5 - lbs ( kg) - 5 lbs ( kg) 8CM- 5-8 lbs (226.8 kg kg) Vertical natural frequency of /2 Hz or less can be achieved over the entire load range. Horizontal natural frequency is load dependent. /2 Hz or less can be achieved at or near the nominal load. Typical Curves: Transmissibility....3 at 2.5 Hz times at 5.5 Hz 5times at Hz times db Low frequency vibration isolator for weight loads from 5 to 8 lbs. and /2 Hz performance vertical and horizontal. The new CM- is a compact high capacity, low-frequency negative-stiffness isolator. As with all Minus K isolators, they are completely passive and use no air or electricity. The isolators can be combined into multi isolator systems to support heavy payloads while taking up very little room themselves. The CM- isolators can be placed on pedestals to bring them to an appropriate height to retrofit your existing air table, enabling you to keep your existing table top and achieve much isolation. The CM- isolators come in several capacity ranges to match your vibration-sensitive instruments such as SPMs (AFMS, STMs, etc), micro-hardness testers, profilers, interferometers, electron microscopes, or other imaging systems. If needed, the CM- isolators can be customized to achieve user specific needs. Eg., different horizontal and vertical frequencies, damping, etc. They can also be made cleanroom and vacuum. compatible. or sales@minusk.com /3 46 Hindy Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright 3 Minus K Technology, Inc. All rights reserved.

7 SM- Low Frequency Vibration Isolator Weight: Approximately 55 lb (7.3 kg) Dimensions: 3" W x 3" D x.5" H (33mm W x33mm D x 52mm H) Load Capacities (approximate): 7SM lb (5-34 kg) SM- 5SM- 9SM- 24SM- 29SM- 34SM- 4SM lb (35-63 kg) 8-55 lb ( kg) - 95 lb ( kg) 8-25 lb (87-34 kg) 24-3 lb (89-36 kg) lb ( kg) 34-4 lb ( kg) Vertical natural frequency of /2 Hz or less can be achieved over the entire load range. Horizontal natural frequency is load dependent. /2 Hz or less can be achieved at or near the nominal load. Typical Curves: Low frequency vibration isolator for weight loads from 5 to 4 lbs. and /2 Hz performance vertical and horizontal. The SM- negative-stiffness isolator is the basic building block of the FP- Floor Platform and other heavy multiple isolator systems. They require no air or electricity. This isolator has the same basic features of our all passive, negative-stiffness, manually-adjustable bench top isolators. It offers our very-low frequency isolation performance for payloads of many thousands of pounds. The SM- isolator can be used alone or with any number of additional units to achieve higher capacity systems. They can be arranged in many geometrical configurations to suit your application. If there is a need, the isolators can be customized to achieve user specific needs. Eg., different horizontal and vertical frequencies, dampening, etc. They can also be made vacuum capatible. The SM- isolators can also be placed on pedestals to increase the height of the isolation system. Transmissibility.. at 2.5 Hz times at 5.5 Hz 5times at Hz times - -4 db or sales@minusk.com / 46 S. Hindy Ave., Unit C, Inglewood, CA 93 Tel: Fax: sales@minusk.com Copyright Minus K Technology, Inc. All rights reserved.

8 NEW WS-4 Compact Vibration Isolation Table Conserve valuable lab space! The WS-4 is a cost effective vibration isolation table for weight loads up to 7 lb. It s a completely passive 6 degree of freedom system requiring NO Air and NO Electricity. Our signature /2 Hz performance for both vertical and horizontal axis s x -x performance than high performance air tables and than active systems Table Weight: Approximately 34 lb (62 kg) Isolator: Approx. 8 lb (36 kg), Stand: Approx. 54 lb (25 kg) Dimensions: 24" W x 24" D x 3" H, (6mm W x 6mm D x 762mm H) Load Capacities (approximate): * Price** WS lb $5,25 (27-48 kg) 5WS lb $5,75 (4-7 kg) 25WS lb $5,39 (82-23 kg) 35WS lb $5,75 (32-68 kg) 5WS lb $5,95 ( kg) 65WS-4 5 to 68 lb ( kg) $6,75 * The Vertical Load Adjustment Crank makes manual adjustments for changes in vertical load simple * Easily determine optimum setting using this simple visual Vertical Load Adjustment Indicator * Dial in Guaranteed /2 Hz or less Vertical natural frequency using the simple Vertical Stiffness Adjustment Screw ( for a typical transmissibility curve with /2 Hz natural frequency) Vertical natural frequency of /2 Hz or less can be achieved over the entire load range. Horizontal natural frequency is load dependent. /2 Hz or less can be achieved at or near the nominal load. Part#: WS-4 Stand Weight: Approximately 54 lb (25 kg) Dimensions: 24" W x 24" D x 2" H, (6mm W x 6mm D x 533mm H) The stand has been designed with a damped Phenolic top which includes locating holes for the leveling feet of the BM-. Compact, sturdy and priced right. Only $875. *Contact Minus K for custom payload ranges. **For International Orders, A Handling Fee of 5% is Added.