User Manual HDM-EXT-0110C. HDMI Extender over Single Cat.X with HDBaseT-Lite & Bi-directional IR 7.1 CH AUDIO. rev: Made in Taiwan

Transcription

1 User Manual HDM-EXT-0110C HDMI Extender over Single Cat.X with HDBaseT-Lite & Bi-directional IR 7.1 CH AUDIO rev: Made in Taiwan

2 Safety and Notice The HDM-EXT-0110C HDMI Extender over Single Cat.X with HDBaseT-Lite & Bidirectional IR has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the HDM- EXT-0110C should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. Follow all instructions and warnings marked on this unit. Do not attempt to service this unit yourself, except where explained in this manual. Provide proper ventilation and air circulation and do not use near water. Keep objects that might damage the device and assure that the placement of this unit is on a stable surface. Use only the power adapter and power cords and connection cables designed for this unit. Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning. TABLE OF CONTENTS INTRODUCTION... 1 FEATURES... 1 SPECIFICATIONS... 2 PACKAGE CONTENTS... 3 PANEL DESCRIPTIONS... 4 Transmitting unit HDM-EXT-0107C [Tx]... 4 Receiving unit HDM-EXT-0107C [Rx]... 5 IR PASS-THROUGH... 6 HARDWARE INSTALLATION... 7 EDID LEARNING... 7 PIN DEFINITION... 8 NOTICE... 9 PERFORMANCE GUIDE... 9

3 INTRODUCTION The HDM-EXT-0110C HDMI Extender over Single Cat.X with HDBaseT, RS-232, Bi-directional IR, Ethernet & POE boosts up your video/audio transmission distance up to 60m (198ft) in HDTV 1080p with 48-bit color depth. HDM-EXT-0110C also supports the most advanced 3D video format complaint with HDMI specification and therefore guarantees the highest 3D video compatibility on the market. With only one cost effective Cat.5/5e/6 cable, users can readily extend HDTV sources from DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display monitors including HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the latest HDMI technology, deep color video, DTS-HD or Dolby TrueHD audio, and HDCP supports and compatibility are all further insured. This flexibility makes HDCP compliant DVD players or PS3 transmit utmost high quality video and audio with a greater distance at the minimal cost, when integrating several components apart. In addition, HDM-EXT-0110C is also equipped with bi-directional IR pass-through path. These bonus features allow users to boost IR control distance up to 60m (198 ft) and makes IR control possible through only single Cat.5/5e/6 cable including HDMI signals. The HDM-EXT-0110C includes two units: transmitting unit HDM-EXT-0110C-TX and receiving unit HDM-EXT-0110C-RX. The transmitting unit is used to capture the input HDMI / DVI signals with IR control packets and carry the signals via one cost effective Cat.5/5e/6 cable. The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR signals. HDM-EXT- 0110C offers the most convenient solution for digital signage with long distance A/V transmission path, and with 10G transmission width ready, HDM-EXT-0110C is ready for your next HDMI generation and applications! FEATURES Support HDMI Deep Color & full 3D & 4K2K@30 (HDBaseT-Lite technology) Extend the transmission up to 60m (198ft) from the HDMI source at Full HD 1080p 48-bit and 40m (130ft) at 4K2K@30 HDCP & EDID Bypass CEC support Auto equalization Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission DTS-HD Master Audio and Dolby TrueHD high bit rate audio support Support full frequency IR signal from 20KHz to 60KHz Bi-directional IR path-through Wall mounting housing design for easy and robust installation i The length depends on the characteristics and quality of the cables. Higher resolutions and longer transmission distances require low skew cables (<25ns/100m) for best performance. Unshielded CAT6 with metal RJ-45 connectors is recommended. 1

4 SPECIFICATIONS Model Name HDM-EXT-0110C Technical HDM-EXT-0110C [Tx] HDM-EXT-0110C [Rx] Role of usage Transmitter [TX] Receiver [RX] HDMI compliance HDCP compliance Video bandwidth Video support HDMI over UTP Audio support Equalization Input TMDS signal Input DDC signal ESD protection HDMI Deep Color, full 3D & Yes Single-link 340MHz [10.2 Gbps] 480i / 480p / 720p / 1080i / 1080p p@60 60m (198ft) [CAT5e] Surround sound [up to 7.1ch] or stereo digital audio Auto 1.2 Volts [peak-to-peak] 5 Volts [peak-to-peak, TTL] [1] Human body model ±19kV [air-gap discharge] & ±12kV [contact discharge] [2] Core chipset ±8kV PCB stack-up 4-layer board [impedance control differential 100Ω; single 50Ω] IR pass-thru Input Output HDMI source control IR remote control HDMI connector RJ-45 connector Rotary control switch 1x HDMI 1x 3.5mm 1x mini-usb 1x RJ-45[HDBaseT] 1x 3.5mm Bi-directional 1x RJ-45[HDBaseT] 1x 3.5mm 1x mini-usb 1x HDMI 1x 3.5mm Controllable via IR pass-through from RX to TX with IR extenders Type A [19-pin female] Mini B WE/SS 8P8C(Reverse Mode) None 3.5mm connector IR receiver / IR blaster IR receiver / IR blaster Mechanical Housing Metal enclosure Model 73 x 89 x 26mm [2.9" x 3.5" x 1"] Dimensions Package 175 x 125 x 216mm [6.8" x 4.9" x 8.5"] [L x W x H] Carton 647 x 366 x 237mm [2'1" x 1'2" x 9.3"] Weight Model 200g [7oz] 196g [6.9oz] Package 900g [2 lbs] Fixedness Wall-mounting case with screws Power supply 5 V2A DC Power consumption 3 Watt [max] 7 Watt [max] Operation temperature 0~40 C [32~104 F] Storage temperature -20~60 C [-4~140 F] Relative humidity 20~90% RH [no condensation] 2

5 PACKAGE CONTENTS 1x HDM-EXT-0110C [TX & RX] 1x IR blaster 1x IR receiver 2x 5V DC power supply 1x User manual CONNECTION WARRANTY 3

6 PANEL DESCRIPTIONS Transmitting unit HDM-EXT-0110C [Tx] Input Panel 1 Latch-locking power jack: Connect to 5V DC power supply 2 LED: Power indicator HDMI IN: Connects to a HDMI source with a HDMI male-male cable 4 IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster 5 IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver Output Panel Mini-USB: F/W update 7 LED: TX/RX link indicator 8 RJ45: Plug in a Cat-5/5e/6 cable that needs to be linked to the transmitting unit HDM-EXT-0110C-RX. 4

7 Receiving unit HDM-EXT-0110C [Rx] Input Panel Latch-locking power jack: Connect to 5V DC power supply 2 LED: Power indicator 3 HDMI OUT: Connects to a HDMI display with a HDMI male-male cable 4 IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster 5 IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver Output Panel 6 Mini-USB: F/W update 7 LED: TX/RX link indicator RJ45: Plug in a Cat-5/5e/6 cable that needs to be linked to the transmitting unit HDM-EXT-0110C-TX. 5

8 IR PASS-THROUGH IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other enf to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. CAUTION! Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. Warranty will not cover the damage. Definition of IR Earphone Jack IR Blaster 1. IR Signal [20-60 khz] 2. Grounding IR Receiver 1. IR Signal [20-60 khz] 2. Grounding 3. Power i You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work. 6

9 HARDWARE INSTALLATION 1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit HDM-EXT- 0110C-TX. 2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit HDM-EXT-0110C-RX. 3. Connect IR Blaster/Receiver to both TX and RX units. 4. Connect a Cat-5/5e/6 cable between the transmitting and receiving units. 5. Make sure this Cat-5/5e/6 cable is tightly connected and not loose. 6. Plug in 5V DC power supply unit to the power jack of the receiving unit HDM-EXT-0110C-RX and the transmitting unit HDM-EXT-0110C-TX. PIN DEFINITION HDMI Type A (Receptacle) HDMI Pin 1 TMDS Data2+ Pin 8 TMDS Data0 Shield Pin 15 SCL Pin 2 TMDS Data2 Shield Pin 9 TMDS Data0 Pin 16 SDA Pin 3 TMDS Data2 Pin 10 TMDS Clock+ Pin 17 DDC/CEC Ground Pin 4 TMDS Data1+ Pin 11 TMDS Clock Shield Pin 18 +5V Power Pin 5 TMDS Data1 Shield Pin 12 TMDS Clock Pin 19 Hot Plug Detect Pin 6 TMDS Data1 Pin 13 CEC Pin 7 TMDS Data0+ Pin 14 Reserved (N.C. on device) 7

10 NOTICE 1. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. Warranty will not cover the damage. 3. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m [1,000ft] bulk cables) can transmit a lot longer signals than stranded UTP cables (usually in the form of fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid UTP Cat-5e cable shows longer transmission range than stranded STP Cat-6 cable. For long extension applications, solid UTP/STP cables are the only viable choice. 4. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance. 5. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable, one can use shielded STP cables to improve EMI problems, which is worsen in long transmission. 6. Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality, the actual transmission range is subject to one s choice of Cat-5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is recommended. 7. If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input #1] generally can produce better transmission performance among all HDMI inputs. Performance rating Type of category cable Wiring Shielding CAT5 CAT5e CAT6 Solid Unshielded (UTP) Shielded (STP) Stranded Unshielded (UTP) Shielded (STP) Termination Please use EIA/TIA-568-B termination (T568B) at any time 8

11 WARRANTY The SELLER warrants the HDM-EXT-0110C HDMI Extender over Single Cat.X with HDBaseT free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working order within 1 year warranty period, The SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifications including static discharge and power surge. This warranty is offered by the SELLER for its BUYER with direct transaction only. This warranty is void if the warranty seal on the metal housing is broken. Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a return authorization number. The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly disclaimed. Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible for shipping charges to and from the SELLER. Cables and power adapters are limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled. The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the HDM-EXT-0110C features and specifications is subject to change without further notice. 9

12