Display Elektronik GmbH TFT MODULE DEM S TMH-PW-N 2,7 TFT. Product Specification Ver.: 2

Transcription

1 Display Elektronik GmbH TFT MODULE 2,7 TFT Product Specification Ver.:

2 Revision History Revision Date Originator Detail Remarks MH Initial Release MH MH Modify Module Parameter Modify Viewing Angle Modify Outline Drawing Modify Schematic Drawing Modify Outline Drawing P4 P6 P26-P27 P11 P26 Version: 2 PAGE: 2

3 Table of Contents No. Item Page 1. General Description Module Parameter Absolute Maximum Ratings DC Characteristics Backlight Characteristic Backlight Characteristics Backlighting circuit Optical Characteristics Optical Characteristics Definition of Response Time Definition of Contrast Ratio Definition of Viewing Angles Definition of Color Appearance Definition of Surface Luminance, Uniformity and Transmittance Block Diagram and Power Supply Interface Pins Definition AC Characteristics wire Serial Interface Input Timing Chart Power On/Off Sequence Quality Assurance Purpose Standard for Quality Test Nonconforming Analysis & Disposition Agreement Items Standard of the Product Visual Inspection Inspection Specification Classification of Defects Identification/marking criteria Packing Reliability Specification Precautions and Warranty Safety Handling Storage Metal Pin (Apply to Products with Metal Pins) Operation Static Electricity Limited Warranty Outline Drawing Version: 2 PAGE: 3

4 1. General Description The specification is a transmissive type color active matrix liquid crystal display (LCD) which uses amorphous thin film transistor (TFT) as switching devices. This product is composed of a TFT-LCD panel, driver ICs, and a backlight unit. 2. Module Parameter Features Details Unit Display Size (Diagonal) LCD Type TN TFT - Display Mode Transmissive / Normally White - Resolution 320 x RGB x 240 Pixels View Direction 6 O clock Best Image Gray Scale Inversion Direction 12 O clock - Module Outline x x 2.40 ( Note1 ) mm Active Area x mm Pixel Size x mm Pixel Arrangement R.G.B.-Delta - Display Colors 262k - Interface 8-Bit-RGB-Interface + 3-Wire-SPI-Interface - With or without touch panel No Touch - Driver IC ILI8961 (Ilitek) - Operating Temperature -20 C to +70 C ºC Storage Temperature -30 C to +80 C ºC Weight (10) g Note 1: Exclusive hooks, posts, FFC/FPC tail etc. 3. Absolute Maximum Ratings VSS=0V, Ta=25ºC Item Symbol Min. Max. Unit Supply Voltage VDD V Storage Temperature TSTG ºC Operating Temperature TOP ºC Note 1: If Ta below 50ºC, the maximal humidity is 90%RH, if Ta over 50ºC, absolute humidity should be less than 60%RH. Note 2: The response time will be extremely slow when the operating temperature is around -10 C, and the back ground will become darker at high temperature operating. Version: 2 PAGE: 4

5 4. DC Characteristics Item Symbol Min. Typ. Max. Unit Supply Voltage VDD V Logic Low Input Voltage VIL GND - 0.3*VDDIO V Logic High Input Voltage VIH 0.7*VDDIO - VDDIO V Logic Low Output Voltage VOL GND - 0.2*VDDIO V Logic High Output Voltage VOH 0.8*VDDIO - VDDIO V Current Consumption All Black Logic Analog ICC+ IIN ma 5. Backlight Characteristic 5.1. Backlight Characteristics Item Symbol Condition Min. Typ. Max. Unit Forward Voltage VF Ta=25 ºC, IF=20mA/LED V Forward Current IF Ta=25 ºC, VF=3.2V/LED ma Power Dissipation PD mw Uniformity Avg % LED Lifetime (25 C) Hrs Drive Method Constant Current LED Configuration 3 White LEDs in Series Note1:LED Lifetime defined as follows: The final brightness is at 50% of original brightness. The environmental conducted under ambient air flow, at Ta=25 C±2 ºC, 60%RH±5%, IF=20mA/LED 5.2 Backlighting Circuit A K Version: 2 PAGE: 5

6 6. Optical Characteristics 6.1. Optical Characteristics Ta=25ºC, VDD=2.8V Specification Item Symbol Condition Min. Typ. Max. Unit Luminance on Backlight On (Transmissive Mode) TFT( I =20mA/LED) f Lv cd/m² Normally Viewing Angle Contrast Ratio(See 6.3) CR θx = φy =0º Response Time TR+TF ms (See 6.2) Red Chromaticity Green Transmissive (See 6.5) Blue White Viewing Horizontal Angle (See 6.4) Vertical XR (0.483) (0.533) (0.583) YR (0.259) (0.309) (0.359) XG (0.239) (0.289) (0.339) YG (0.535) (0.585) (0.635) XB (0.096) (0.146) (0.196) YB (0.060) (0.110) (0.160) XW (0.206) (0.256) (0.306) YW (0.258) (0.308) (0.358) θx θx Center CR 10 Deg. φy φy NTSC Ratio(Gamut) % 6.2. Definition of Response Time Normally Black Type (Negative) Relative Brightness Non-selected state 100% 90% Selected state Non-selected state 10% 0% Tr Tf Tr is the time it takes to change form non-selected stage with relative luminance 10% to selected state with relative luminance 90%; Tf is the time it takes to change from selected state with relative luminance 90% to non-selected state with relative luminance 10%. Note: Measuring machine: LCD-5100 Version: 2 PAGE: 6

7 Normally White Type (Positive) Relative Brightness Non-selected state Selected state Non-selected state 100% 90% 10% 0% Tr Tf Tr is the time it takes to change form non-selected stage with relative luminance 90% to selected state with relative luminance 10%; Tf is the time it takes to change from selected state with relative luminance 10% to non-selected state with relative luminance 90%; Note: Measuring machine: LCD-5100 or EQUI 6.3. Definition of Contrast Ratio Contrast is measured perpendicular to display surface in reflective and transmissive mode. The measurement condition is: Measuring Equipment Eldim or Equivalent Measuring Point Diameter 3mm//1mm Measuring Point Location Active Area centre point A: All Pixels white Test pattern B: All Pixel black Contrast setting Maximum Definitions: CR (Contrast) = Luminance of White Pixel / Luminance of Black Pixel 6.4. Definition of Viewing Angles Measuring machine: LCD-5100 or EQUI Version: 2 PAGE: 7

8 6.5. Definition of Color Appearance R, G, B and W are defined by (x, y) on the IE chromaticity diagram NTSC=area of RGB triangle/area of NTSC trianglex100% Measuring picture: Red, Green, Blue and White (Measuring machine: BM-7) 6.6. Definition of Surface Luminance, Uniformity and Transmittance Using the transmissive mode measurement approach, measure the white screen luminance of the display panel and backlight Surface Luminance: LV = average (LP1:LP9) Uniformity = Minimal (LP1:LP9) / Maximal (LP1:LP9) * 100% Transmittance = LV on LCD / LV on Backlight * 100% Note: Measuring machine: BM-7 X X/6 X/3 X/3 X/6 Display Area Y c Y/6 Y/3 Y/3 Y/ Version: 2 PAGE: 8

9 7. Block Diagram and Power Supply Version: 2 PAGE: 9

10 8. Interface Pins Definition No. Symbol Function Remark 1 VCOM Vcom voltage. 2 FB(K) LED Cathode. 3 VLED(A) LED Anode. 4 DRV Power transistor signal for back light power boost converter. Output 5 VCAC Power setting capacitor for VCOM AC. Output 6 VCOMDC VCOM DC output. Output 7 FRP Frame polarity output for panel VCOM Output 8 AGND Ground for analog circuit. Power 9 VGL Power setting capacitor connect pin. Capacitor PIN 10 VGH Power setting capacitor connect pin. Capacitor PIN 11 C4M Capacitor connect pin for internal charge pump. Capacitor PIN 12 C4P Capacitor connect pin for internal charge pump. Capacitor PIN 13 VINT3 Floating this pin. Capacitor PIN 14 VINT2 Floating this pin. Capacitor PIN 15 C3M Capacitor connect pin for internal charge pump. Capacitor PIN 16 C3P Capacitor connect pin for internal charge pump. Capacitor PIN 17 VINT1 Power setting capacitor connect pin. Capacitor PIN 18 C2M Capacitor connect pin for internal charge pump. Capacitor PIN 19 C2P Capacitor connect pin for internal charge pump. Capacitor PIN 20 C1M Capacitor connect pin for internal charge pump. Capacitor PIN 21 C1P Capacitor connect pin for internal charge pump. Capacitor PIN 22 DVDD Power setting capacitor connecting pins.(internal core use, typical 1.8 V) Capacitor PIN 23 VDDIO Power supply for digital interface. Power 24 VDD Power supply for charge pump circuits. Power 25 DGND Ground for digital circuits. Power 26 D0 Data bus. Input 27 D1 Data bus. Input 28 D2 Data bus. Input 29 D3 Data bus. Input 30 D4 Data bus. Input 31 D5 Data bus. Input 32 D6 Data bus. Input 33 D7 Data bus. Input 34 DCLK Clock signal. 35 VSYNC Vertical Sync input. 36 HSYNC Horizontal Sync input. 37 SCL Serial clock signal. 38 SDA Serial data. 39 CS Chip select signal. 40 VCOM Vcom voltage. Version: 2 PAGE: 10

11 Version: 2 PAGE: 11

12 9. AC Characteristics Wire Serial Interface Version: 2 PAGE: 12

13 Version: 2 PAGE: 13

14 9.2. Input Timing Chart 8-Bit RGB Input Timing Chart Parallel RGB Input Timing Version: 2 PAGE: 14

15 9.3. Power On/Off Sequence Power On Sequence Power Off Sequence Version: 2 PAGE: 15

16 10. Quality Assurance Purpose This standard for Quality Assurance assures the quality of LCD module products supplied to customer Standard for Quality Test Sampling Plan: GB Single sampling, general inspection level II Sampling Criteria: Visual inspection: AQL 1.5% Electrical functional: AQL 0.65% Reliability Test: Detailed requirement refer to Reliability Test Specification Nonconforming Analysis & Disposition Nonconforming analysis: Customer should provide overall information of non-conforming sample for their complaints After receipt of detailed information from customer, the analysis of nonconforming parts usually should be finished in one week If cannot finish the analysis on time, customer will be notified with the progress status Disposition of nonconforming: Non-conforming product over PPM level will be replaced The cause of non-conformance will be analyzed. Corrective action will be discussed and implemented Agreement Items Shall negotiate with customer if the following situation occurs: There is any discrepancy in standard of quality assurance Additional requirement to be added in product specification Any other special problem. Version: 2 PAGE: 16

17 10.5. Standard of the Product Visual Inspection Appearance inspection: The inspection must be under illumination about lx, and the distance of view must be at 30cm ± 2cm The viewing angle should be 45 from the vertical line without reflection light or follows customer's viewing angle specifications Definition of area: A Zone: Active Area, B Zone: Viewing Area, Eye Eye A zone B zone Basic principle: A set of sample to indicate the limit of acceptable quality level must be discussed by both us and customer when there is any dispute happened New item must be added on time when it is necessary Inspection Specification No. Item Criteria (Unit: mm) 01 Black / White spot Foreign material (Round type) Pinholes Stain Particles inside cell. (Minor defect) b φ= ( a + b) /2 a Area Size Acc. Qty φ 0.10 Ignore 0.10<φ <φ <φ 0 Total 2 no include φ 0.10 Distance between 2 defects should more than 3mm apart. Version: 2 PAGE: 17

18 02 Electrical Defect (Minor defect) Display Area Total Bright dot 0 0 Dark dot N 2 N 2 Note1 Total dot N 2 N 2 Mura Not visible through 5% ND filters. Note 2 Remark: 1. Bright dot caused by scratch and foreign object accords to item 1. W Black and White line L L 03 Scratch Foreign material (Line type) (Minor defect) Length Width Acc. Qty / W 0.03 Ignore L < W L < W / 0.1 < W 0 Total 3 Distance between 2 defects should more than 3mm apart. Scratches not viewable through the back of the display are acceptable. 04 Glass Crack (Minor defect) Crack is potential to enlarge, any type is not allowed. Version: 2 PAGE: 18

19 05 Glass Chipping Pad Area: (Minor defect) Length and Width Acc. Qty c > 3.0, b< c< 3.0, b< a<glass Thickness 06 Glass Chipping Rear of Pad Area: (Minor defect) Length and Width Acc. Qty c > 3.0, b< c< 3.0, b< c< 3.0, b< a<glass Thickness 07 Glass Chipping Except Pad Area: (Minor defect) Length and Width Acc. Qty c > 3.0, b< c< 3.0, b< c< 3.0, b< a<glass Thickness 08 Glass Corner Chipping: (Minor defect) Length and Width Acc. Qty c < 3.0, b< 3.0 Ignore a<glass Thickness Version: 2 PAGE: 19

20 Glass Burr: (Minor defect) Length F < 1.0 Acc. Qty Ignore 09 Glass burr don t affect assemble and module dimension. 10 FPC Defect: (Minor defect) a w a 10.1 Dent, pinhole width a<w/3. (w: circuitry width.) 10.2 Open circuit is unacceptable No oxidation, contamination and distortion. 11 Bubble on Polarizer (Minor defect) Diameter Acc. Qty φ 0.20 Ignore 0.20 <φ <φ < φ None 12 Dent on Polarizer (Minor defect) Diameter Acc. Qty φ 0.20 Ignore 0.20 <φ <φ < φ None 13 Bezel 13.1 No rust, distortion on the Bezel No visible fingerprints, stains or other contamination. Version: 2 PAGE: 20

21 D: Diameter W: width L: length 14.1 Spot: D<0.25 is acceptable 0.25 D 0.4 2dots are acceptable and the distance between defects should more than 10 mm. 14 Touch Panel D>0.4 is unacceptable 14.2 Dent: D>0.40 is unacceptable 14.3 Scratch: W 0.03, L 10 is acceptable, 0.03<W 0.10, L 10 is acceptable Distance between 2 defects should more than 10 mm. W>0.10 is unacceptable No distortion or contamination on PCB terminals. 15 PCB 15.2 All components on PCB must same as documented on the BOM/component layout Follow IPC-A-600F. 16 Soldering Follow IPC-A-610C standard The below defects must be rejected Missing vertical / horizontal segment, 17.2 Abnormal Display No function or no display. Electrical Defect 17.4 Current exceeds product specifications. (Major defect) 17.5 LCD viewing angle defect No Backlight Dark Backlight Touch Panel no function. Remark: LCD Panel Broken shall be rejected. Defect out of LCD viewing area is acceptable Classification of Defects Visual defects (Except no / wrong label) are treated as minor defect and electrical defect is major Two minor defects are equal to one major in lot sampling inspection Identification/marking criteria Any unit with illegible / wrong /double or no marking/ label shall be rejected. Version: 2 PAGE: 21

22 10.9. Packing There should be no damage of the outside carton box, each packaging box should have one identical label Modules inside package box should have compliant mark All direct package materials shall offer ESD protection Note1: Bright dot is defined as the defective area of the dot is larger than 50% of one sub-pixel area. Bright dot: The bright dot size defect at black display pattern. It can be recognized by 2% transparency of filter when the distance between eyes and panel is 350mm±50mm. Dark dot: Cyan, Magenta or Yellow dot size defect at white display pattern. It can be recognized by 5% transparency of filter when the distance between eyes and panel is 350mm±50mm. Note2: Mura on display which appears darker / brighter against background brightness on parts of display area. Version: 2 PAGE: 22

23 11. Reliability Specification No Item Condition Quantity Criteria 1 High Temperature Operating +70 C, 96Hrs 2 2 Low Temperature Operating -20 C, 96Hrs 2 3 High Humidity +50 C, 90%RH, 96Hrs 2 4 High Temperature Storage +80 C, 96Hrs 2 5 Low Temperature Storage -30 C, 96Hrs 2 6 Thermal Cycling Test 7 Packing vibration 8 Electrical Static Discharge -20 C, 60min~+70 C, 60min, 20 cycles. Frequency Range:10Hz~50Hz Acceleration of Gravity:5G X, Y, Z 30 min for each direction. Air:±8kV 150pF/330Ω 5 times Contact:±4kV 150pF/330Ω 5 times GB/T GB/T GB/T GB/T GB/T GB/T GB/T GB/T Drop Test (Packaged) Height:80 cm,1 corner, 3 edges, 6 Surfaces. Note1. No defection cosmetic and operational function allowable. Note2. Total current Consumption should be below double of initial value 2 GB/T Version: 2 PAGE: 23

24 12. Precautions and Warranty Safety The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water Since the liquid crystal cells are made of glass, do not apply strong impact on them. Handle with care Handling Reverse and use within ratings in order to keep performance and prevent damage Do not wipe the polarizer with dry cloth, as it might cause scratch. If the surface of the LCD needs to be cleaned, wipe it swiftly with cotton or other soft cloth soaked with petroleum IPA, do not use other chemicals Storage Do not store the LCD module beyond the specified temperature ranges Strong light exposure causes degradation of polarizer and color filter Metal Pin (Apply to Products with Metal Pins) Pins of LCD and Backlight Solder tip can touch and press on the tip of Pin LEAD during the soldering Recommended Soldering Conditions Solder Type: Sn96.3~94-Ag3.3~4.3-Cu0.4~1.1 Maximum Solder Temperature: 370 Maximum Solder Time: 3s at the maximum temperature Recommended Soldering Temp: 350±20 Typical Soldering Time: 3s Solder Wetting Solder Pin Lead Solder Pin Lead Recommended Not Recommended Pins of EL Solder tip can touch and press on the tip of EL leads during soldering No Solder Paste on the soldering pad on the motherboard is recommended Recommended Soldering Conditions Solder type: Nippon Alimit Leadfree SR-34, size 0.5mm Recommended Solder Temperature: 270~290 Typical Soldering Time: 2s Minimum solder distance from EL lamp (body):2.0mm No horizontal press on the EL leads during soldering bend EL leads three times is not allowed. Version: 2 PAGE: 24

25 Solder Wetting Recommended The type of the solder iron: Not Recommended Solder Pad Recommended Not Recommended Operation Do not drive LCD with DC voltage Response time will increase below lower temperature Display may change color with different temperature Mechanical disturbance during operation, such as pressing on the display area, may cause the segments to appear fractured Do not connect or disconnect the LCM to or from the system when power is on Never use the LCM under abnormal condition of high temperature and high humidity Module has high frequency circuits. Sufficient suppression to the electromagnetic interface shall be done by system manufacturers. Grounding and shielding methods may be important to minimize the interference Do not display the fixed pattern for long time(we suggest the time not longer than one hour)because it may develop image sticking due to the TFT structure Static Electricity CMOS LSIs are equipped in this unit, so care must be taken to avoid the electro-static charge, by ground human body, etc The normal static prevention measures should be observed for work clothes and benches The module should be kept into anti-static bags or other containers resistant to static for storage Limited Warranty Our warranty liability is limited to repair and/or replacement. We will not be responsible for any consequential loss If possible, we suggest customer to use up all modules in six months. If the module storage time over twelve months, we suggest that recheck it before the module be used After the product shipped, any product quality issues must be feedback within three months, otherwise, we will not be responsible for the subsequent or consequential events. Version: 2 PAGE: 25

26 13. Outline Drawing Tear Tape (1) (3.02) Eyes 39.1±0.2/BL 37.1±0.2/TFT 33.06/LCD A.A 2.7" TFT 320 x RGB x 240 Single Area Single Area 29.8± ±0.2 5± ±0.3 (2.57) (1) 58.8/LCD A.A 61.94±0.2/CF 65.37±0.2/TFT 67.5±0.2/BL 26.8±0.5 STIFFENER 2.4±0.2 CONTACT SIDE 0.3±0.05 / E WYW AK 3± P0.5*(40-1)=19.5(W=0.3) 0.5± ±0.15 (5) A K NOTES: 1.Display type:2.7"tft 2.Viewing direction:6 O'CLOCK 3.Gray Scale Inversion Direction:12 O'CLOCK 4.Polarizer mode:transmissive/normal white 5.Operation temperature:-20 C~+70 C 6.Storage temperature:-30 C~+80 C 7.Driver IC:ILI Power supply voltage:2.8v 9.Backlight :White(3 LED)/9.6V(TYP)/20mA Brightness:230cd/m²(TYP) 10.ROHS must be complied * Unspecification tolerance are ±0.2mm VCOM FB(K) VLED(A) DRV VCAC VCOMDC FRP AGND VGL VGH C4M C4P VINT3 VINT2 C3M C3P VINT1 C2M C2P C1M C1P DVDD VDDIO VDD DGND D0 D1 D2 D3 D4 D5 D6 D7 DCLK VSYNC HSYNC SCL SDA CS VCOM Version: 2 PAGE: 26