Um MT INSPECTION SCOPE INSTRUCTION MANUAL NANOMETER TECHNOLOGIES

Transcription

1 Um MT INSPECTION SCOPE INSTRUCTION MANUAL NANOMETER TECHNOLOGIES

2 Um MT Inspection Scope INSTRUCTION MANUAL Document Number RE:UmMT-IS-01A Nanometer Technologies (NMT) has prepared this manual for use by NMT personnel, licensees, and customers. The information contained herein is the property of NMT and shall not be reproduced in whole or in part without the prior written approval of NMT. NMT reserves the right to make changes without notice to the specification(s) and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical or listing errors. Please address any questions, comments and suggestions to: NANOMETER TECHNOLOGIES INC 2501 GOLDEN HILL RD PASO ROBLES, CA Tel: (805) Fax: (805) September 5th, 2014 ii

3 TABLE OF CONTENTS Um MT Inspection Scope DIAGRAM & SPECS 1 Setting up the Um MT 2 Step 1 - Selecting Fiber Row 3 Step 2 - Inserting Connector 3 Step 3 - Selecting Fiber #1 4 Step 4 - Focusing Fiber 4 Step 5 - Adjusting Image Intesity 5 Step 6 - Fine Tune image Height 5 Step 7 - Selecting Fiber #2 6 Inspection Notes 6 Notes 7 Warranty 8 iii

4 Um MT DIAGRAM LAYOUT Power Switch Power Light Power Input Composite Video Out Internal LED Brightness Control MT Connector Slot Individual Fiber Dial Upper/Lower Row Fiber Select Arm SPECIFICATIONS Size: 7.5 W x 5.25 L x 3.25 H Weight: 3lbs Optics: 800x Video: 720x480 Power: 12VDC Focus Knob (1)

5 Setting up Um MT To set up the Um MT, you will need the following items: 12 VDC Power Supply BnC to RCA Connector RCA USB Video Addapter 12 VDC Power Supply BnC to RCA Connector RCA USB Video Addapter Plug in the 12VDC Power Supply into the Power Slot. Plug power suppply into a standard 120VAC wall socket. Attach the BnC Adapter to the Video Out. Attach the RCA Cable to the BnC Adapter. Turn Power on. Plug USB Video Adapter into an open USB slot on computer. The Um MT video output can also be plugged directly into a monitor. Use a Composite to VGA Adapter to use with a VGA compatible monitor. (2)

6 STEP 1 Setting Connector Row Lower Row (Left Side) Upper Row (Right Side) Center Row Adjust the Fiber Row Arm to the style of MT connector being inspected. Center Position - Standard 12 Fiber MT Connector Right Position - Upper row of 24 Fiber MT Connector Left Position - Lower row of 24 Fiber MT Connector STEP 2 Inserting Connector Insert MT Connector into the Connector Slot. IMPORTANT: Insert connector with the epoxy window DOWN. (3)

7 STEP 3 Selecting Fiber #1 Line up number to Guide Turn the Individual Fiber Dial to the #1 postion. Make sure the number lines up with the guide on the right side of the dial. STEP 4 Focusing the Fiber Focus Dial Adjust the Focus Dial to sharpen the image on the screen. (4)

8 STEP 5 Adjust Image Intensity Adjust the Intesity Dial to brighten/darken the screen image STEP 6 Adjust Fiber Image Height Use the Fiber Row Arm to finely tune the center height of the fiber image on the screen. Inspect the fiber. (5)

9 STEP 7 Selecting Fiber #2 Line up number to Guide Turn the Individual Fiber Dial to the #2 postion to inspect the 2nd Fiber. Keep turning the Individual Fiber Dial to the next number to inspect all 12 fibers. If inspecting a 24 fiber MT connector, start with the Upper Row of fibers then use the Fiber Row Arm to change to the Bottom Row. Again use the Fiber Row Arm to fine adjust the center height on the screen. Use the Focus Dial to refocus the image if necessary. The UM MT Inspection Scope is compatible with the Eagle Inspect software for testing and saving inspection images. For more information about the Eagle Inspect software visit (6)

10 NOTES:

11 Limited Warranty Nanometer Technologies products shall be free of defects in material and workmanship for a period of 1 year from the date of purchase. Nanometer Technologies fixture plates shall be free of defects in material and workmanship for a period of 90 days from the date of purchase. In the event of a defect in materials or workmanship, we will either replace or repair without charge (not including shipping costs) at our option any part which in our judgment shows evidence of such defect within 1 year (90 days for fixture plates) from the date of purchase. This warranty does not apply to misuse, abuse, tampered, altered items, overuse of water or UPS solution, dropping the fixture plate, or hitting the fixture plate while suspended from pneumatic arm. At the end of the warranty period Nanometer Technologies shall be under no further obligation expressed or implied. This warranty is in lieu of any other warranty, under no circumstances will Nanometer Technologies be liable for any loss, damage, expense or consequential damages of any kind arising in connection with the use or inability to use Nanometer Technologies products. Warranty will be voided if tamper seals are broken on any product or unit is opened by any person not authorized by Nanometer Technologies without prior permission.

12