MODEL NO.: M170EGE SUFFIX: L20

Size: px

Start display at page:

Download "MODEL NO.: M170EGE SUFFIX: L20"

Bathsheba Williamson
5 years ago
Views:

1 Tentative Specification Preliminary Specification Approval Specification MODEL NO. M7EGE SUFFIX L2 Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation with your signature and comments. Approved By Checked By Prepared By Version 25 July 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

2 CONTENTS. GENERAL DESCRIPTION...5. OVERVIEW GENERAL SPECIFICATINS MECHANICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT ELECTRICAL ABSOLUTE RATINGS TFT LCD MODULE BACKLIGHT UNIT ELECTRICAL SPECIFICATIONS FUNCTION BLOCK DIAGRAM INTERFACE CONNECTIONS ELECTRICAL CHARACTERISTICS LCD ELETRONICS SPECIFICATION Vcc Power Dip Condition BACKLIGHT UNIT (LED matrix is 2S4P) LIGHTBAR Connector Pin Assignment LVDS INPUT SIGNAL SPECIFICATIONS LVDS DATA MAPPING TABLE COLOR DATA INPUT ASSIGNMENT DISPLAY TIMING SPECIFICATIONS POWER ON/OFF SEQUENCE OPTICAL CHARACTERISTICS TEST CONDITIONS OPTICAL SPECIFICATIONS RELIABILITY TEST ITEM PACKING PACKING SPECIFICATIONS PACKING METHOD PALLET CMI MODULE LABEL PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS STORAGE PRECAUTIONS OPERATION PRECAUTIONS...27 Version 25 July 2 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

3 9.4 SAFETY PRECAUTIONS SAFETY STANDARDS OTHER...27 Appendix. OUTLINE DRAWING...27 Version 25 July 2 3 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

4 REVISION HISTORY Version Date Page Description. 2/3/2 All Spec Ver. was first issued. Version 25 July 2 4 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

5 . GENERAL DESCRIPTION. OVERVIEW M7EGE-L2 is a 7 TFT Liquid Crystal Display module with WLED Backlight unit and 32 pins 2ch-LVDS interface. This module supports 28 x 24 SXGA mode and can display up to 6.7M colors. The converter module for Backlight is not built in..2 GENERAL SPECIFICATIONS Item Specification Unit Note Screen Size 7 real diagonal - - Driver Element a-si TFT active matrix - - Pixel Number 28 x R.G.B. x 24,SXGA resolution pixel - Pixel Pitch.264 (H) x.264 (V) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 6.7M color - Transmissive Mode Normally white - - Surface Treatment AG type, 3H hard coating, Haze Luminance, White 25nits (Typ.) Cd/m2 Color Gamut 72% of NTSC(Typ.) - - TCO TCO 5. compliance Power Consumption Total 6.26 W cell 5. W (Max.), BL.26W (Max.) () Note () The specified power consumption Total= cell (reference 4.3.)+BL (reference 4.3.3) 2. MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Horizontal (H) mm Module Size Vertical (V) mm () Thickness (T) -.5. mm Bezel Area Horizontal mm Vertical mm Active Area Horizontal mm Vertical mm Weight g Note () Please refer to the attached drawings for more information of front and back outline dimensions. Version 25 July 2 5 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

6 3. ABSOLUTE MAXIMUM RATINGS 3. ABSOLUTE RATINGS OF ENVIRONMENT Item Symbol Value Min. Max. Unit Note Storage Temperature TST -2 6 ºC () Operating Ambient Temperature TOP 5 ºC (), (2) Note () (a) 9 %RH Max. (Ta <= 4 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). (c) No condensation. Note (2) The temperature of panel surface should be ºC min. and 6 ºC max. 3.2 ELECTRICAL ABSOLUTE RATINGS 3.2. TFT LCD MODULE Item Symbol Value Min. Max. Unit Power Supply Voltage VCCS V Logic Input Voltage V IN V Note () Version 25 July 2 6 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

7 3.2.2 BACKLIGHT UNIT Item LED Forward Current Per Input Pin LED Pulse Forward Current Per Input Pin Symbol Value Min. Typ Max. Unit I F ma I P ma Note (), (2) Duty=% (), (2) Pulse Width msec. and Duty 3% Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for input pin of LED light bar at Ta=25±2 (Refer to and for further information). 4. ELECTRICAL SPECIFICATIONS 4. FUNCTION BLOCK DIAGRAM Version 25 July 2 7 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

8 4.2. INTERFACE CONNECTIONS PIN ASSIGNMENT Pin Name Description GND GND 2 RXO- Negative LVDS differential data input. Channel O (odd) 3 RXO+ Positive LVDS differential data input. Channel O (odd) 4 RXO- Negative LVDS differential data input. Channel O (odd) 5 RXO+ Positive LVDS differential data input. Channel O (odd) 6 RXO2- Negative LVDS differential data input. Channel O2 (odd) 7 RXO2+ Positive LVDS differential data input. Channel O2 (odd) 8 GND GND 9 RXOC- Negative LVDS differential clock input. (odd) RXOC+ Positive LVDS differential clock input. (odd) RXO3- Negative LVDS differential data input. Channel O3(odd) 2 RXO3+ Positive LVDS differential data input. Channel O3 (odd) 3 RXE- Negative LVDS differential data input. Channel E (even) 4 RXE+ Positive LVDS differential data input. Channel E (even) 5 GND GND 6 RXE- Negative LVDS differential data input. Channel E (even) 7 RXE+ Positive LVDS differential data input. Channel E (even) 8 GND GND 9 RXE2- Negative LVDS differential data input. Channel E2 (even) 2 RXE2+ Positive LVDS differential data input. Channel E2 (even) 2 RXEC- Negative LVDS differential clock input. (even) 22 RXEC+ Positive LVDS differential clock input. (even) 23 RXO3- Negative LVDS differential data input. Channel O3(odd) 24 RXO3+ Positive LVDS differential data input. Channel O3 (odd) 25 GND GND 26 NC For LCD internal use only, Do not connect 27 NC For LCD internal use only, Do not connect 28 NC For LCD internal use only, Do not connect 29 Vcc +5.V power supply 3 Vcc +5.V power supply 3 Vcc +5.V power supply 32 GND GND Note () Connector Part No. GS2332-3R-7H (FOXCONN) Note (2) User s connector Part No Mating Wire Cable Connector Part No. FI-X3H(JAE) or FI-X3HL(JAE) Mating FFC Cable Connector Part No (P-TWO) or JF5X3- (JAE). Note (3) The first pixel is odd. Note (4) Input signal of even and odd clock should be the same timing. Version 25 July 2 8 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

9 , (odd),2 2, 2,2 3,,3 (even) (odd),4 (even) Pitch,Xmax Pitch Ymax, Ymax, Xmax 4.3 ELECTRICAL CHARACTERISTICS 4.3. LCD ELETRONICS SPECIFICATION Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage Vcc V - Ripple Voltage V RP 3 mv - Rush Current I RUSH 3 A (2) White 35 5 ma (3)a Power Supply Current Black ma (3)b Vertical Stripe ma (3)c Power Consumption PLCD Watt (4) LVDS differential input voltage Vid 6 mv (5) LVDS common input voltage Vic.2 V (5) Logic High Input Voltage VIH. V (5) Logic Low Input Voltage VIL -. V (5) Note () The ambient temperature is Ta = 25 ± 2 ºC. Note (2) Measurement Conditions2 Version 25 July 2 9 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

10 Version 25 July 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

Note (3) The specified power supply current is under the conditions at Vcc = 5. V, Ta = 25 ± 2 ºC, Fr = 75Hz, whereas a power dissipation check pattern below is displayed.

11 Note (3) The specified power supply current is under the conditions at Vcc = 5. V, Ta = 25 ± 2 ºC, Fr = 75Hz, whereas a power dissipation check pattern below is displayed. Note (4) The power consumption is specified at the pattern with the maximum current. Note (5) VID waveform condition Version 25 July 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

12 4.3.2 Vcc Power Dip Condition BACKLIGHT UNIT Parameter LED Light Bar Input Voltage Per Input Pin Symbol Value Min. Typ. Max. VPIN V Unit Note (), Duty=%, IPIN=65mA (), (2) Duty=% LED Light Bar Current IPIN ma Per Input Pin LED Life Time LLED 4 Hrs (3) LED Light Bar Power Consumption PBL W () Duty=%, IPIN=65mA Note () LED light bar input voltage and current are measured by utilizing a true RMS multimeter as shown below Note (2) PBL Typ = IPIN Typ VPIN Typ ( 4 ) PBL Max = IPIN Max VPIN Typ ( 4 ) input pins, LED light bar circuit is (2)Series, (4)Parallel. Note (3) The lifetime of LED is defined as the time when LED packages continue to operate under the conditions at Ta = 25 ±2 and I= (65)mA (per chip) until the brightness becomes 5% of its original value. Version 25 July 2 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

13 4.3.4 LIGHTBAR Connector Pin Assignment Connector WM N (FCN) or Compatible 2 L/B connector drawing Version 25 July 2 3 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

14 CN Pin Description number Cathode of LED string 2 Cathode of LED string 3 VLED 4 VLED 5 Cathode of LED string 6 Cathode of LED string Note () User s Mating Connector Part No. CI46SL-NH (CviLux) or Compatible. 4.4 LVDS INPUT SIGNAL SPECIFICATIONS 4.4. LVDS DATA MAPPING TABLE LVDS Channel O LVDS output D7 D6 D4 D3 D2 D D Data order OG OR5 OR4 OR3 OR2 OR OR LVDS Channel O LVDS output D8 D5 D4 D3 D2 D9 D8 Data order OB OB OG5 OG4 OG3 OG2 OG LVDS Channel O2 LVDS output D26 D25 D24 D22 D2 D2 D9 Data order DE NA NA OB5 OB4 OB3 OB2 LVDS Channel O3 LVDS output D23 D7 D6 D D D5 D27 Data order NA OB7 OB6 OG7 OG6 OR7 OR6 LVDS Channel E LVDS output D7 D6 D4 D3 D2 D D Data order EG ER5 ER4 ER3 ER2 ER ER LVDS Channel E LVDS output D8 D5 D4 D3 D2 D9 D8 Data order EB EB EG5 EG4 EG3 EG2 EG LVDS Channel E2 LVDS output D26 D25 D24 D22 D2 D2 D9 Data order DE NA NA EB5 EB4 EB3 EB2 LVDS Channel E3 LVDS output D23 D7 D6 D D D5 D27 Data order NA EB7 EB6 EG7 EG6 ER7 ER6 Version 25 July 2 4 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

15 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory! Version 25 July 2 5 / COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G 7 G 6 G 5 G 4 G3 G2 G G B 7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green() / Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Note () Low Level Voltage, High Level Voltage

16 4.5 DISPLAY TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency Fc MHz - Period Tc ns Input cycle to cycle jitter T rcl -.2*TC ---.2*TC ns () Input Clock TLVCCS -.2*TC ---.2*TC ns (2) LVDS Clock Vertical Display Term to data skew Spread spectrum modulation range Spread spectrum modulation frequency Fclkin_ mod.97*fc ---.3*FC MHz F SSM 2 KHz Frame Rate Fr Hz Total Tv Th Tv=Tvd+Tvb- Active Tvd 24 Th - Display Blank Tvb 2 42 Th - Total Th Tc Th=Thd+Thb Active Horizontal Display Term Thd 64 Tc - Display Blank Thb 5 24 Tc - Note Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored. (3) INPUT SIGNAL TIMING DIAGRAM Version 25 July 2 6 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

17 Note () The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T TI Note (2) Input Clock to data skew is defined as below figures. Note (3) The SSCG (Spread spectrum clock generator) is defined as below figures. Version 25 July 2 7 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

18 4.6 POWER ON/OFF SEQUENCE The power sequence specifications are shown as the following table and diagram. Timing Specifications Parameters Values Min Typ. Max Units T. ms T2 3 5 ms T ms T4 25 ms T5 2 5 ms T6. 5 ms T7 ms Note () The supply voltage of the external system for the module input should be the same as the definition of Vcc. Note (2) When the backlight turns on before the LCD operation of the LCD turns off, the display may momentarily become abnormal screen. Note (3) In case of VCC = off level, please keep the level of input signals on the low or keep a high impedance. Note (4) T4 should be measured after the module has been fully discharged between power off and on period. Note (5) Interface signal shall not be kept at high impedance when the power is on. Note (6) CMI won t take any responsibility for the products which are damaged by the customers not following the Power Sequence. Note (7) There might be slight electronic noise when LCD is turned off (even backlight unit is also off). To avoid this symptom, we suggest "Vcc falling timing" to follow "t6 spec". Version 25 July 2 8 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

19 5. OPTICAL CHARACTERISTICS 5. TEST CONDITIONS Item Symbol Value Unit Ambient Temperature Ta 25±2 o C Ambient Humidity Ha 5± %RH Supply Voltage V CC 2 V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" LED Light Bar Input Current Per Input Pin I PIN 65±.9 ma DC PWM Duty Ratio D % LED Light Bar Test Converter TEST T2-D 5.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 5.2. The following items should be measured under the test conditions described in 5. and stable environment shown in Note (5). Item Symbol Condition Min. Typ. Max. Unit Note Rx TBD Red Ry TBD Gx TBD Color Green Gy Typ TBD Typ + Chromaticity Bx θ x =, θ Y = - (), (5).3 TBD.3 (CIE 93) Blue CS-2 By TBD R=G=B=255 Wx.33 White Gray scale Wy.329 Center Luminance of White L (Center of Screen) C cd/m 2 (4), (5) Contrast Ratio Response Time White Variation Viewing Angle Viewing Angle CR (2), (5) T R - 4 θ T x =, θ Y = ms (3) F θ W x =, θ Y = 75 % (5), (6) Horizontal θx- + θx+ CR Vertical θy- + θy Horizontal θx- + θx+ CR Vertical θy- + θy Deg. (), (5) Deg. (), (5) Version 25 July 2 9 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

20 Note () Definition of Viewing Angle (θx, θy) Note (2) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L L255 Luminance of gray level 255 L Luminance of gray level CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (T R, T F ) Version 25 July 2 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

21 Note (4) Definition of Luminance of White (L C ) Measure the luminance of gray level 255 at center point L C = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (6). Note (5) Measurement Setup The LCD module should be stabilized at given temperature for 4 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 4 minutes in a windless room. Note (6) Definition of White Variation (δw) Measure the luminance of gray level 255 at 9 points δw = (Minimum [L () ~ L (9)] / Maximum [L () ~ L (9)] ) *% Version 25 July 2 2 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

22 6. RELIABILITY TEST ITEM Items Required Condition Note Temperature Humidity Bias (THB) Ta= 5, 8%RH, 24hours High Temperature Operation (HTO) Ta= 5, 24hours Low Temperature Operation (LTO) Ta=, 24hours High Temperature Storage (HTS) Ta= 6, 24hours Low Temperature Storage (LTS) Ta= -2, 24hours Vibration Test (Non-operation) Acceleration.5 G Wave Half-sine Frequency - 3 Hz Sweep 3 Minutes each Axis (X, Y, Z) Shock Test (Non-operation) Acceleration 5 G Wave Half-sine Active Time ms Direction ± X, ± Y, ± Z.(one time for each Axis) -2 /3min, 6 / 3min, Thermal Shock Test (TST) cycles 25,On/sec, Off /sec, 3, On/Off Test cycles Contact Discharge ± 8KV, ESD (Electro Static Discharge) 5pF(33 ) Air Discharge ± 5KV, 5pF(33 ) Operation, ft / 24hours Altitude Test Non-Operation3, ft / 24hours Note () criteria Normal display image with no obvious non-uniformity and no line defect. Note (2) Evaluation should be tested after storage at room temperature for more than two hour Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. The fixing condition is shown as below Version 25 July 2 22 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

23 7. PACKING 7. PACKING SPECIFICATIONS () 7 LCD modules / Box (2) Box dimensions448(l) X 322 (W) X 39(H) mm (3) Weight approximately 2kg (7 modules per box) 7.2 PACKING METHOD () Carton Packing should have no failure in the following reliability test items. Test Item Test Conditions Note Vibration ISTA STANDARD Random, Frequency Range.47Grms X,Y,Z three axes (3min /axis) Frequency Non Operation 5Hz(.5G 2 /Hz) Hz(.5G 2 /Hz) 2Hz(.37G 2 /Hz) Dropping Test Corner, 3 Edge, 6 Face, 6cm Non Operation Figure. 7- Packing method Version 25 July 2 23 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

24 7.3 PALLET For Sea/Land Transportation(2ft/4ft Container) Figure. 7-2 Packing method Version 25 July 2 24 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

25 8. CMI MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. (a) Model Name M7EGE-L2 (b) CMI barcode definition Serial ID Z Z 2 Z 3 Z 4 Z 5 Z 6--Z 7--Z 8 Z 9 Z Z Z 2 Code Meaning Description Z internal use - Z 2 Z 3 Z 4 Year,Month,Date Year ~9, 2=, 2=, 22=2, 23=3 Month ~2=, 2, 3, ~, 9, A, B, C Day ~3=, 2, 3, ~, 9, A, B, C, ~, W, X, Y, exclude I, O, and U. Z 5 internal use - Z 6 internal use - Z 7 Code of grade G, 2, 3, 5, E Z 8 Z 9 Z Z Z 2 Serial No Module manufacture sequence no Version 25 July 2 25 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

26 (c) Customer s barcode definition Serial ID CM-HE2-X-X-X-XX-L-XX-L-YMD-NNNN Code Meaning Description CM Supplier code CMI=CM HE2 Model number M7EGE-L2= HE2 X Revision code Non ZBD,2,~,8,9 / ZBD A~Z X Source driver IC code Century=, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6, Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C, X Gate driver IC code OKI=D, Philips=E, Renasas=F, Samsung=G, Sanyo=H, Sharp=I, TI=J, Topro=K, Toshiba=L, Windbond=M, ILITEK=Q, Fiti=Y, None IC =Z XX Cell location Tainan Taiwan=TN, Ningbo China=CN, Hsinchu Taiwan=SC L Cell line #,2,~,9,A,B,~,Y,Z XX Module location Tainan, Taiwan=TN ; Ningbo China=NP, Shenzhen China=SH L Module line #,2,~,9,A,B,~,Y,Z YMD Year, month, day Year ~9, 2=, 22=2, 23=3 2=, 2=, 22=2 Month ~2=, 2, 3, ~, 9, A, B, C Day ~3=, 2, 3, ~, 9, A, B, C, ~, T, U, V NNNN Serial number By LCD supplier (d) FAB ID(UL Factory ID) Region TWCMI NBCMI NBCME NHCMI 9. PRECAUTIONS Factory ID GEMN LEOO CANO CAPG 9. ASSEMBLY AND HANDLING PRECAUTIONS () Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating. Version 25 July 2 26 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

27 (9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. ()When ambient temperature is lower than ºC may reduce the display quality. For example, the response time will become slowly. 9.2 STORAGE PRECAUTIONS () Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from to 35 and relative humidity of less than 7% (2) Do not store the TFT LCD module in direct sunlight (3) The module should be stored in dark place. It is prohibited to apply sunlight or fluorescent light in storing 9.3 OPERATION PRECAUTIONS () The LCD product should be operated under normal condition. Normal condition is defined as below Temperature 2±5 Humidity 65±2% Display pattern continually changing pattern(not stationary) (2) If the product will be used in extreme conditions such as high temperature,high humidity,high altitude,display pattern or operation time etc It is strongly recommended to contact CMI for application engineering advice. Otherwise, Its reliability and function may not be guaranteed. 9.4 SAFETY PRECAUTIONS () If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (2) After the module s end of life, it is not harmful in case of normal operation and storage. 9.5 SAFETY STANDARDS The LCD module should be certified with safety regulations as follows () UL695- or updated standard. (2) IEC695- or updated standard. 9.6 OTHER When fixed patterns are displayed for a long time, remnant image is likely to occur. Appendix. OUTLINE DRAWING Version 25 July 2 27 / 29 One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

28 I. ME Drawing () Front view C HIM EI Version 25 July 2 28 / 29 The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited. One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

29 (2) Back view CHIM EI Version 25 July 2 29 / 29 The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited. One step solution for LCD / PDP / OLED panel application Datasheet, inventory and accessory!

MODEL NO.: M215HGE SUFFIX: L10

MODEL NO.: M215HGE SUFFIX: L10 Doc. Number Tentative Specification Preliminary Specification Approval Specification MODEL NO. M25HGE SUFFIX L Customer Common Model APPROVED BY SIGNATURE Name / Title Note Product Version C/C2 Please