OPERATING MANUAL. Cole-Parmer Stir-Pak. Mixer Head Model Numbers , , , , & Mixer Controller Model Numbers

Size: px
Start display at page:

Download "OPERATING MANUAL. Cole-Parmer Stir-Pak. Mixer Head Model Numbers , , , , & Mixer Controller Model Numbers"

Transcription

1 OPERATING MANUAL Cole-Parmer Stir-Pak Mixer Head Model Numbers , , , , & Mixer Controller Model Numbers Cole-Parmer ServoDyne Mixer Head Model Numbers , , , & Mixer Controller Model Number Cole-Parmer 625 East Bunker Court Vernon Hills, Illinois U.S.A Toll Free: Phone: Fax: Version 11Nov08 Rev1

2 SAFETY PRECAUTIONS High voltages exist and are accessible in the controller. Contact Cole-Parmer for servicing. Do not operate mixers where explosive vapors or flammable materials exist. Death or serious injury could result. Check NEC and local codes before installing. Never clean the controller or mixer head while power is applied to the system. Use only those mixer shafts that are properly sized for the mixer head being used. Refer to mixer head specifications for the proper shaft diameter or range to be used. Sizes other than those specified can cause injury to personnel or damage to equipment. Disconnect the AC power input line cord before connecting the mixer head cable. Exercise extreme care when adjusting mixer height and/or position to avoid personal injury. Never make these adjustments while the mixer shaft is rotating. Never insert or remove the mixer shaft/impeller while the mixer shaft is rotating. Be sure speed control is fully counterclockwise before the POWER switch is placed in the FWD or REV positions. ( Controller) Check that all cords are clear of any moving parts and not subject to splashes or spills. Use care when setting the operating speed of the mixer. Operation at high speeds in small mixing vessels could result in hazardous splashing on the operator and equipment. When running at full speed and load at higher ambient temperatures, the mixer head may get very hot to the touch. Use of mixing shafts and impellers larger than those recommended could result in poor product performance and shortened service life. Mixer shafts must be inserted into high-speed through-shaft mixers at least 3 inches (8 mm) and the collet hand-tightened firmly to ensure adequate shaft retention. Keep mixer shafts as short as possible to reduce resonant vibrations caused by the shaft flexing at higher speeds. The mixer head is to be used only for mixing. It is not intended for any other purpose

3 INTRODUCTION The Stir-Pak series heavy-duty modular mixing system covered in this manual consists of four different mixer heads and a analog controller 115VAC operation. The ServoDyne series digital modular mixing system consists of four different mixer heads and a precision digital controller for 115VAC operation. The following chart cross-references the model number, operating speed range and torque rating of the mixer heads and the compatible controller. MIXER HEAD CONTROLLER OPERATING VOLTAGE SPEED RANGE, rpm MAXIMUM TORQUE, oz-in (kg-cm) VAC, 50/60 Hz 2 to (24.5) VAC, 50/60 Hz 9 to (5) VAC, 50/60 Hz 23 to (3.2) VAC, 50/60 Hz 60 to (1.2) VAC, 50/60 Hz 3 to (24.5) VAC, 50/60 Hz 20 to (5) VAC, 50/60 Hz 60 to (3.2) VAC 50/60 Hz 150 to (1.2) , STIR-PAK CONTROLLER The variable-speed controller, Figure 1a and 1b, is used to set the speed of the mixer heads and provides a 100:1 adjustment range. FORWARD-OFF- POWER ON SPEED REVERSE SWITCH INDICATOR CONTROL The controller ensures accurate, dependable motor speed (mixing) control, with soft-start and smooth, gradual adjustment to the speed setting. Constant speed with a 100:1 adjustment range is maintained electronically via automatic compensation for changes in load torque demands at both high and low speeds. Built-in motor current compensation minimizes speed drift with changes in load. Motor current limiting protects the system in case of a locked rotor condition. Output circuit protection protects against inadvertent output shorting. Mixer rotation is reversible. MOTOR CONNECTOR Figure 1a: Display and Controls LINE CORD Figure 1b: Controller Rear Panel

4 SERVODYNE CONTROLLER/DISPLAY FUNCTIONS Four-digit LED display shows selected mixing time, mixing time remaining, rpm, and torque values. Displays last countdown setting. Starts counting down when you press the START key. Displays the last mixer shaft speed. Displays current torque value (in-oz for 115VAC model; cm-kg for 230VAC model) and high and low torque limits. Mixer automatically stops when preset limits are reached. Zeroes the torque when impeller is running in free air or in a reference fluid. LEDs indicate the function being displayed (time, rpm, or torque). A flashing time or torque light and audible alarm indicate that a limit condition has been reached. Increases value of parameter. Decreases value of parameter. Press at any time to stop mixer. Starts mixer. Stops when countdown reaches zero. Figure 2a: Controller Functions IEC 320 power entry module POWER SWITCH All settings are retained in memory. IN-RS-232C IN-Connect cable from host computer. OUT-RS-232C OUT-Connect cable to next mixer. MIXER HEAD PLUG RECEPTACLE Multi-pin plug enables microprocessor to identify connected mixer head and properly control speed and torque. FUSE T3.15A (115VAC) T1.6A (230VAC) Figure 2b: Controller Rear Panel

5 INSTALLATION AND SETUP PROCEDURES The mixer heads are equipped with an adjustable-tilt mounting assembly. The mounting assembly is designed to be attached to an optional mixer support stand or tank clamp. Components supplied as part of the mixer package include the following: Mixer head with 6-ft cable Precision controller with 6-ft line cord 3-jawed chuck on high-torque mixers ⅜-inch collet on high-speed mixers Adjustable-tilt mounting assembly with support rod Installation of Adjustable-Tilt Mounting Never insert or remove the mixer shaft/impeller while the mixer shaft is rotating. Perform the following steps: 1. Attach mixer head to adjustable-tilt mounting assembly as follows: a. For Stir-Pak models , -20, and ServoDyne models , -20, attach mounting assembly with four screws and lock washers. (See Figure 3a) Figure 3a: , -20 and , -20 mixer head mounting b. For Sir-Pak models , -40, and ServoDyne models , -40, attach mounting assembly with two screws and lock washers. (See Figure 3b) Note: Figure 3b: , -40 and , -40 mixer head mounting The mixer is now ready to be attached to a support stand or to a tank clamp (not supplied). Recommended stands, tank clamps, and a double (rod) clamp are available through Cole- Parmer. Part numbers are listed in the ACCESSORIES section

6 Installation Using a Support Stand 1. Set up support stand in accordance with the manufacturer s instructions. 2. Attach a double (rod) clamp to the vertical rod on the support stand and tighten clamp screw. (See Figure 4) 3. Slide rod of adjustable-tilt mounting assembly into clamp and secure with clamp screw. 4. Select an impeller and shaft for the required operation and install as follows: a. Place impeller on shaft and tighten set screw. b. For high-torque mixers head, slide the shaft of the stirring device into the threejawed chuck and tighten chuck. c. For high-speed mixer head, slide the shaft through the collet at least 3 inches and hand-tighten collet. 5. Place support stand legs around vessel. Tilt angle is adjustable from 0 to 30 degrees. Exercise extreme care when adjusting mixer head height and/or position to avoid personal injury. Never make these adjustments while the mixer shaft is rotating. Mixer shafts must be inserted into high-speed through-shaft mixers at least 3 inches and the collet hand-tightened firmly to ensure adequate shaft retention. Keep mixer shafts as short as possible to reduce resonant vibrations caused by shaft flexing at higher speeds. 6. Position the height of the mixer head by moving the clamp up or down on the support stand or, on highspeed models, by loosening the collet and positioning the shaft

7 Figure 4: Typical mixer setup using a support stand and pivot mount (ServoDyne system shown) Note: The controller can be placed on any flat surface within 6 feet of the mixer head or can be mounted on a support platform (not supplied) or a pivot mount (not supplied). Refer to the ACCESSORIES section for part numbers. To attach the support platform proceed with step 7. To attach the pivot mount proceed with step 8. If controller is placed elsewhere proceed with step To install the support platform proceed as follows: a. Attach a double (rod) clamp to the vertical support rod and position so that platform will be clear of mixer head. b. Slide the mounting rod of the support platform into the double (rod) clamp and tighten clamp. c. Place controller on platform and proceed to step To install the pivot mount proceed as follows: a. Remove the two cap nuts from the mounting studs on bottom of controller (see Figure 4). b. Position pivot mount bracket over two studs, reinstall two cap nuts and tighten. c. Attach a double (rod) clamp to the vertical support rod on the stand and position so that pivot mount bracket will be clear of mixer head. d. Slide the mounting rod of the pivot mount bracket into the double (rod) clamp and tighten clamp. e. Adjust position of controller by first loosening knob on pivot mount bracket, adjust position and then retighten knob. Check that all cords are clear of any moving parts and not subject to splashes or spills. 9. Connect the 6-foot cable between the mixer head and the controller rear panel. 10. Check that the controller is not powered. a. For Stir-Pak controller, ensure that the FWD-OFF-REV switch is in the OFF position. b. For the ServoDyne controller, check that the rear panel ON-OFF switch is in the OFF position. 11. Connect the 6-ft line cord from the controller to the appropriate 3-wire, grounded power source. Be sure the SPEED control is fully counterclockwise before the POWER switch is placed in the FWD or REV positions (Stir-Pak models only). 12. Place the red safety switch on the top of the mixer head in the On 1 position. The mixer is now ready to operate

8 Installation Using a Tank Clamp The tank clamp is attached to the side of a tank and supports both the mixer head and the controller (see Figure 5). 1. Position the tank clamp over the edge of the tank with large knob to the outside of tank. 2. Allow clamp to rest on edge of tank for added stability and tighten knob. 3. Position mixer head over material to be mixed and insert mixer mounting shaft into upper hole in tank clamp, tighten locking knob securely. 4. Select an impeller and shaft for the required operation and install as follows: a. Place impeller on shaft and tighten set screw. b. For high-torque mixer head, slide the 5/16 inch to 3/8 inch shaft of the stirring device into the keyless chuck and tighten. c. For high-speed mixer head, slide the inch mixer shaft through the collet and tighten collet. Be sure only (+/ ) inch shafts are used. Contact Cole-Parmer or your dealer for obtaining the proper shaft size. Refer to the ACCESSORIES section for the part numbers. Exercise extreme care when adjusting mixer head height and/or position to avoid personal injury. Never make these adjustments while the mixer shaft is rotating. Mixer shafts must be inserted into high speed throughshaft mixers at least 3 inches and the collet hand-tightened firmly to ensure adequate shaft retention. Keep mixer shafts as short as possible to reduce resonant vibrations caused by the shaft flexing at higher speeds. Do not operate mixers where explosive vapors or flammable materials exist. Death or serious injury could result. Check NEC and local codes before installing. Figure 5: Typical mixer setup using a tank clamp (ServoDyne controller shown)

9 5. Position the height of the mixer head on high-speed models by loosening the collet and positioning the shaft. Note: The controller can be placed on any flat surface within 6 feet of the mixer head and can be mounted on a support platform (not supplied) or a pivot mount (not supplied). Refer to ACCESSORIES for part numbers. To attach the support platform, proceed with step 6. To attach the pivot mount, proceed with step 7. If controller is placed elsewhere, proceed with step To install the support platform proceed as follows: a. Slide the mounting rod of the support platform into the lower hole on the tank clamp and tighten clamp. b. Place controller on platform and proceed to step To install the pivot mount proceed as follows: a. Remove the two cap nuts from the mounting studs on bottom of controller. b. Position pivot mount bracket over two studs, reinstall two cap nuts and tighten. c. Slide the mounting rod of the pivot mount bracket into the lower hole on the tank clamp and tighten clamp. d. Adjust position of controller by first loosening knob on pivot mount bracket, adjusting position and then retighten knob. 8. Connect the 6-foot cable between the mixer head and the controller rear panel. 9. Check that the rear panel ON-OFF switch is in the OFF position. 10. Connect the 6-ft line cord from the controller to the appropriate power source, either a VAC 50/60Hz 3-wire, grounded power source. 11. Place the red safety switch on the top of the mixer head in the On 1 position. Check that all cords are clear of any moving parts and not subject to splashes or spills. Be sure the SPEED control is fully counterclockwise before the POWER switch is placed in the FWD or REV positions (Stir-Pak models only). The mixer is now ready to operate. Always wear appropriate eye protection when mixing any kind of fluid. Avoid wearing loose clothing that may be caught by a rotating mixer shaft. Use care when setting the operating speed of the mixer. Operation at high speeds in small mixing vessels could result in hazardous splashing on the operator and equipment. Be sure the SPEED control is fully counterclockwise before the POWER switch is placed in the FWD or REV positions (Stir-Pak models only)

10 STIR-PAK CONTROLLER OPERATION FWD-OFF-REV Switch In the FWD position, the shaft will rotate in a counterclockwise direction when viewed from the impeller. The center or OFF position removes power from both the controller and mixer head. In the REV position, the shaft will rotate in a clockwise direction when viewed from the impeller. FORWARD-OFF-REVERSE SWITCH POWER ON INDICATOR LIGHT SPEED CONTROL POWER Indicator The green LED indicator illuminates whenever the FWD-OFF-REV switch is in either the FWD or REV position. SPEED Control The SPEED control precisely sets the output speed of the shaft. The controller has a range of 100:1 depending on the model; shaft speed can be as low as 2RPM or as high as 6000RPM. Slowly adjust the SPEED Control from the 0 position to a setting that provides the desired mixing speed. Always return the speed control to the 0 position when mixing is complete. To stop the mixer head in an emergency, place the FWD- OFF-REV switch in the OFF position or remove the power plug. Be sure the SPEED control is fully counterclockwise before the POWER switch is placed in the FWD or REV positions. Use care when setting the operating speed of the mixer. Operation at high speeds in small mixing vessels could result in hazardous splashing on the operator and equipment. When running at full speed and load at higher ambient temperatures, the mixer head may get very hot to the touch. Never insert or remove the mixer shaft/impeller while the mixer shaft is rotating. Note: With new mixing heads, allow approximately 20 minutes run-in time to allow warm-up drift to become minimal SERVODYNE CONTROLLER OPERATION Power On Internal memory permits storage of all previously set parameters including speed, torque, time and calibration constant. Turning the rear-panel mounted ON/OFF switch to the ON position energizes the display without running the motor. The display will come up in the last mode operated. Depressing the start button causes the mixer motor shaft to rotate at the previously programmed speed. Depressing the stop button stops the motor. Changing Display Modes (TIME, RPM, TORQUE) is accomplished by pressing the desired mode button once. Additional operation of the mode button advances operation to the set mode

11 Set Run Time The use of the TIME button in conjunction with the buttons permits entry of a desired mixing time. Pressing the button once when already in the time display mode causes the left (minutes) digit to flash, pressing the button once again causes the right two (seconds) digits to flash. During this period the time can be set with the buttons. Pressing the button a third time starts the countdown provided the motor is running; otherwise the display shows the set time. An audible alarm will sound and the LED will flash when preset time reached. Maximum programmable time is 99 minutes 59 seconds. A 0 programmed time results in continuous motor operation. Set Motor Speed Depressing the RPM button when in the RPM mode causes the display to flash and read the set motor speed. Use the buttons to set the desired speed. Set Motor Torque Limit The TORQUE limit feature provides for the setting of both HI and LO torque limits. Depressing the TORQUE button when in the TORQUE mode causes the first digit of the display to read either on H or L (for High or Low limit) and the last three digits to flash and read the set limit. Pressing the buttons changes the set torque limit. Pressing the Torque button once again while the digits are flashing causes the H or L to flash while the set limit digits stop flashing. It is now that the High or Low limit can be selected by pressing either the buttons. Pressing any button other than buttons returns the display to actual torque. If the motor is running while the torque limit is being modified, the previously programmed limit will be in effect until the torque limit mode is exited; then the new limit will take over. Regardless of the set torque limit, there is always a maximum torque limit check to guard against motor overheating. If this limit is exceeded, the motor stops, the alarm sounds and the in-oz LED flashes. Pressing any key causes the display to return to what was previously displayed before the alarm. The error must be corrected or the over-limit warning will sound again when the motor is restarted. Set Torque Zero The TORQUE ZERO button is used to zero the torque display so that the actual torque necessary to mix something can be read directly on the display. To use this feature, the TORQUE ZERO button is pressed while the mixer head shaft is running in free air; the display will zero. The mixer shaft is then placed into the solution being mixed, the reading on the display will now indicate the torque necessary to mix the solution. This number can now be used to determine the proper shut off or torque limit when mixing several batches of the same consistency. When the TORQUE ZERO button is operated, the maximum torque limit that can be set is adjusted so that the absolute torque does not exceed the continuous torque of the mixer head being used. Example: The operator has set a high torque limit of 50 oz-in for a motor rated for 65. The motor is then running with an actual torque reading of 30 oz-in. When the TORQUE ZERO button is pressed, the maximum torque that can be set would be 35 (65-30). Since the set limit of 50 is above this, it will automatically be changed to 35. The operator will see this when the set mode is entered, which will prevent a setting over 35. Never insert or remove the mixer shaft/impeller while the mixer shaft is rotating. When running at full speed and load at higher ambient temperatures, the mixer head may get very hot to the touch

12 Specifications Mixer Head Direction of Rotation: Speed Range: Torque Output, max: Mixer Shaft Interface: Stir-Pak Series Bi-directional controlled with the FWD-OFF-REV switch ServoDyne Series CCW (Viewed from Impeller end) to 180 rpm to 180 rpm to 900 rpm to 900 rpm to 2300 rpm to 2300 rpm to 6000 rpm to 6000 rpm CONTINUOUS INTERMITTENT and in-oz 510 in-oz and in-oz 105 in-oz and in-oz 65 in-oz and in-oz 25 in-oz , , , , jawed type chuck with key accepts 5/16 in. to 3/8 in. dia shaft Collet accepts (± ) inch diameter shaft Input Voltage, max: , -20, -30, -40, , -20, -30, Volts DC Input Current, max: , -40, , Amps DC , -20, , Amps DC Installation Category: Installation Category I per IEC 664 (Signal level parts of equipment) Construction: Dimensions (L x dia) 11.5 in. x 3.6 in. (292 x 92 mm) Weight 8 lb (3.5 kg) Enclosure rating IP 24 per IEC 34-5 Environment: Operating temperature 0 to 40 C (32 to 104 F) Storage temperature Storage: 45 to 65 C (49 to 149 F) Humidity (noncondensing) 10% to 90% Altitude Less than 2000 m Degree of pollution Pollution Degree 2 per IEC 664 (Indoor Usage lab, office) Chemical Resistance: Exposed material is painted aluminum, plastic, and vinyl Compliance: 115VAC CAN/CSA C22.2, No nd Edition CAN/CSA-C22.2 No ANSI/UL nd Edition UL61010A st Edition

13 Specifications Controller Output: Speed regulation: Input: Model Maximum Voltage, V Maximum Current, Amps Maximum Power, Watts Model Line Load Drift ±1% F.S. ±2% F.S. ±10% F.S ±0.25% F.S. ±0.25% F.S. ±0.25% F.S. Display Maximum settable countdown timer Time accuracy Four-digit, seven-segment LED 99 minutes, 59 seconds ±1 second Model Voltage Maximum Current, Amps Maximum Power to 130VAC RMS, 50/60 Hz 3 Amps 360 VA to 130VAC RMS, 50/60 Hz 2.3 Amps 280 VA Installation Category: Installation Category II per IEC 664 (Local level appliances, portable equipment, etc.) Computer Control: RS-232-C (Full Duplex) Construction: Environment: Dimensions (L x W x H) 7 x 5 x 3½ inches 7¾ x 6½ x 3½ inches (178 x 127 x 89 mm) (197 x 165 x 89 mm) Weight 1.4 lb (0.62 kg) 3 lb (1.4 kg) Enclosure rating IP 22 per IEC 529 IP 22 per IEC 529 Operating temperature 0 to 40 C (32 to 104 F) Storage temperature -45 to 65 C (-49 to 149 F) Humidity (noncondensing) 10% to 90% Altitude < 2000 m Degree of pollution 2 per IEC 664, (indoor usage lab, office) Chemical Resistance: Exposed material is painted aluminum, plastic, and vinyl Compliance: 115VAC CAN/CSA C22.2, No nd Edition CAN/CSA-C22.2 No ANSI/UL nd Edition UL61010A st Edition

14 MAINTENANCE AND TROUBLESHOOTING Maintenance is limited to replacement of motor brushes on the mixer head, replacing the fuse on the controller, and cleaning the unit. If a fault is detected when troubleshooting and cannot be corrected by the suggested remedy, contact Cole-Parmer or your dealer for service. Motor Brush Check/Replacement Note: Brushes should be checked every 6 months or 1000 operating hours or if erratic operation occurs. Erratic operation may occur immediately after brush replacement. Allow motor to run up to an hour to allow brushes to seat. 1. Turn the controller off a. For the Stir-Pak controllers, place the FWD-OFF-REV switch in the OFF position b. For the ServoDyne controller, place the rear panel ON-OFF switch in the OFF position. 2. Disconnect the AC line cord from the AC receptacle. 3. Disconnect the mixer head cable from the receptacle on the rear of the controller. 4. Carefully unscrew each brush holder cap. Withdraw the brush and examine it for wear. Note: Replace both brushes if either brush is less than inch (8 mm) long. The replacement brushes (set of 2) part number is listed under REPLACEMENT PARTS. 5. Insert brushes into brush holder on each side of motor as shown in Figure 6 and screw in brush holder caps. 6. Reconnect mixer head to rear-panel connector on controller. 7. Reconnect controller to primary power source. Figure 6: Motor brush orientation ServoDyne Controller Fuse Replacement 1. Place the power switch in the OFF position. 2. Disconnect the AC power input line cord from the AC receptacle. 3. Remove and check the fuse and replace if defective. 4. Reconnect the AC power input line cord to the AC receptacle. Cleaning the Mixer/Controller System Keep the mixer housing and controller enclosure clean with mild detergents. Never immerse nor use excessive fluid. Never clean the Controller or Mixer Head while power is applied to the system

15 Replacement Parts No user-serviceable parts are inside of this instrument. Refer servicing to Cole-Parmer or your dealer. The following parts are user-replaceable: Description For model(s) Part Number Speed Control Knob Fuse, T3.15A Motor Brushes (2) All Jawed Chuck Assembly , -20, , Collet Nut , -40, , Pivot Assembly Knob (1) All Cordset USA (115VAC) Contact Cole-Parmer or your dealer if you have service needs. Troubleshooting Stir-Pak Symptom Cause Remedy Disconnected or defective line cord Mixer shaft does not rotate when controller is switched to FWD or REV regardless of SPEED control setting. POWER indicator does not glow. Mixer shaft does not rotate when controller is switched to FWD or REV regardless of SPEED control setting. POWER indicator glows. Troubleshooting ServoDyne Defective fuse Defective mixer head or controller 1. Check that the unit is plugged into a live line. 2. For 115VAC unit: Return for service (fuse is not user replaceable) 1. Check mixer cable connections at rear of the controller - make sure connector is fully inserted into the receptacle 2. Check motor brushes (see motor brush check/replacement for details) 3. Replace mixer head or controller with known working unit, if available, to determine source of the problem 4. Return for service 5. Check that the red safety switch on the mixer head in the On 1 position. The controller microprocessor detects and indicates system faults. The display alternately shows the error number and a FAIL message. The following table summarizes the faults and suggested corrective action. The system cannot be operated until the fault is corrected. Error Code Fault Corrective Action Err1 No mixer head connection Plug mixer head into controller. Err2 Invalid mixer head Bad motor cable - return mixer head for repair. Err3 Safety Switch in Off 0 Check that the red safety switch on the mixer head in the position, No encoder pulses On 1 position. Return mixer head and controller for repair. Err4 Motor speed is excessive Return mixer head and controller for repair. Err5 No torque information display Return controller for repair. Err6 Bad PROM check Return controller for repair. Err7 Motor overload Check mixer for obstructions. Turn off unit to clear error. Err8 Zero cross failure Return controller for repair. Err9 Bad EEPROM data Return controller for repair

16 HI Limit Message A flashing HI limit message will be displayed and the mixer head will stop if the maximum rated torque of the mixer head is exceeded when the low torque limit mode is being used. To protect the mixer head motor from overheating, it cannot be restarted until the fault is corrected. Note: ACCESSORIES Before contacting Cole-Parmer or your dealer for repair, try to determine whether the fault is in the controller or mixer head. The best way is to substitute a known good unit, if available, and recheck. The accessories listed below, used for mounting the mixer head and controller, are available from Cole- Parmer or your dealer. Many other accessories such as shafts and impellers are also available. Contact your dealer for the full line of available accessories. WARRANTY Part Name Part Number Tank Clamp Controller Support Platform Pivot Mount Controller Support Support Stand Double (Rod) Clamp Software ServoDyne RS-232-C Interface Cable Satellite Cable Shaft, 12 inches (305 mm) Shaft, 18 inches (457 mm) Shaft, 24 inches (610 mm) Shaft, 30 inches (762 mm) The manufacturer warrants this product to be free from significant deviations from published specifications. If repair or adjustment is necessary within the warranty period, the problem will be corrected at no charge if it is not due to misuse or abuse on your part as determined by the manufacturer. Repair costs outside the warranty period, or those resulting from product misuse or abuse, may be invoiced to you. The warranty period for this product is noted on the Warranty Card. PRODUCT RETURN To limit charges and delays, contact Cole-Parmer or manufacturer for authorization and shipping instructions before returning the product, either within or outside of the warranty period. When returning the product, please state the reason for the return. For your protection, pack the product carefully and insure it against possible damage or loss. Any damages resulting from improper packaging are your responsibility. TECHNICAL ASSISTANCE If you have any questions about the use of this product, contact Cole-Parmer or your local dealer SSMPK027 Rev 2.01

Tube Rotator. User Guide. Version 1.2

Tube Rotator. User Guide. Version 1.2 Tube Rotator User Guide Version 1.2 Figure 1: Fixed Speed Model Tube holder spindle Tilt adjustment wheel IEC power inlet socket (at rear) Power on/off switch Figure 2: Variable Speed Model Tube holder

More information

OPERATING MANUAL FIXED FLOW PUMP DRIVES

OPERATING MANUAL FIXED FLOW PUMP DRIVES OPERATING MANUAL FIXED FLOW PUMP DRIVES Model Nos. 7540-01 7540-30 7542-12 7540-02 7540-60 7542-20 7540-06 7542-01 7542-30 7540-12 7542-02 7542-60 7540-20 7542-06 Note: Drive is shown with optional Pump

More information

EN - English Washington Street Melrose, MA Phone Toll Free Revision 4 20/06/17

EN - English Washington Street Melrose, MA Phone Toll Free Revision 4 20/06/17 - English... 1 Instruction Manual Vortex Mixer, Mini Fix Speed, VXMNFS Vortex Mixer, Mini Analog, VXMNAL Vortex Mixer, Mini Digital, VXMNDG Vortex Mixer, Mini Pulsing, VXMNPS 99 Washington Street Melrose,

More information

Basic Vortex Mixer Standard Vortex Mixer Advanced Vortex Mixer Pulsing Vortex Mixer

Basic Vortex Mixer Standard Vortex Mixer Advanced Vortex Mixer Pulsing Vortex Mixer Instruction Manual Manual Basic Vortex Mixer Standard Vortex Mixer Advanced Vortex Mixer Pulsing Vortex Mixer Table of Contents Package Contents............... 1 Warranty............... 1 Installation...............

More information

Instruction Manual Fixed Speed Vortex Mixer Analog Vortex Mixer Digital Vortex Mixer Pulsing Vortex Mixer

Instruction Manual Fixed Speed Vortex Mixer Analog Vortex Mixer Digital Vortex Mixer Pulsing Vortex Mixer Instruction Manual Fixed Speed Vortex Mixer Analog Vortex Mixer Digital Vortex Mixer Pulsing Vortex Mixer Table of Contents Package Contents............ 1 Warranty............ 1 Installation............

More information

Tube Roller Shakers. User Guide. Version 1.2

Tube Roller Shakers. User Guide. Version 1.2 Tube Roller Shakers User Guide Version 1.2 Control panel Rollers Side retaining panels Analog models LED display Drip tray (not visible) Digital models Power On/Off and control dial Roller retaining panel

More information

K Service Source. Apple High-Res Monochrome Monitor

K Service Source. Apple High-Res Monochrome Monitor K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal

More information

Model DT-311J. And DT-311J-230V(AC) DIGITAL STROBOSCOPE INSTRUCTION MANUAL

Model DT-311J. And DT-311J-230V(AC) DIGITAL STROBOSCOPE INSTRUCTION MANUAL Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com Model DT-311J And DT-311J-230V(AC) DIGITAL STROBOSCOPE INSTRUCTION MANUAL 1. GENERAL The DT-311J DIGITAL

More information

K Service Source. Apple High-Res Monochrome Monitor

K Service Source. Apple High-Res Monochrome Monitor K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal

More information

Advanced Digital Melting Point Apparatus

Advanced Digital Melting Point Apparatus Advanced Digital Melting Point Apparatus User Guide Version 1.1 Figure 1: Front view Sample heating block Power on/off (at rear) Printer output (at rear) LCD screen Viewer Capillary storage Control panel

More information

Flat-Bed Module Recorders

Flat-Bed Module Recorders Flat-Bed Module Recorders Model No. 08376-50 08376-55 08376-60 0115-0192 4/28/00 Table of Contents Introduction...3 Power Requirements...3 Chart Paper Installation...3 Pen Installation...5 Grounding...5

More information

VPM2. Operation Manual

VPM2. Operation Manual VPM2 Operation Manual Whip Corporation 361 Farmington Ave. P.O. Box 17183 Louisville, KY 40217-0183 USA 502-637-1451 800-626-5651 Fax 502-634-4512 www.whipmix.com LISTED Features The Whip VPM2 is designed

More information

ACCESSORIES MANUAL PART NUMBER: PRODUCT REVISION: 1 PNP202. Interconnect Box USER'S GUIDE

ACCESSORIES MANUAL PART NUMBER: PRODUCT REVISION: 1 PNP202. Interconnect Box USER'S GUIDE MANUAL PART NUMBER: 400-0109-001 PRODUCT REVISION: 1 PNP202 Interconnect Box USER'S GUIDE INTRODUCTION Your purchase of the PNP202 Interconnect Box is greatly appreciated. We are sure you will find it

More information

Operating Manual. Automated Gear. Apollo Design Technology, Inc Fourier Drive Fort Wayne, IN USA

Operating Manual. Automated Gear. Apollo Design Technology, Inc Fourier Drive Fort Wayne, IN USA Operating Manual Automated Gear Apollo Design Technology, Inc. 4130 Fourier Drive Fort Wayne, IN 46818 USA PH: +01(260)497-9191 FX: +01(260)497-9192 www.apollodesign.net 11-25-09 5-6 POWERING UP THE RIGHT

More information

OPERATION AND MAINTENANCE MANUAL

OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE MANUAL SERIAL NUMBER CUSTOMER: SALES REP.: CONTENTS Mixer Installation / Assembly / Dimension Drawings Safety... 1 Customer Service Contact... 1 Initial Inspection... 2 Installation...2

More information

VPM2. Operator's Manual

VPM2. Operator's Manual VPM2 Operator's Manual Whip Mix Corporation 361 Farmington Ave. P.O. Box 17183 Louisville, KY 40217-0183 USA 502-637-1451 800-626-5651 Fax 502-634-4512 www.whipmix.com Features The Whip Mix VPM2 is designed

More information

ACCESSORIES MANUAL PART NUMBER: TNP500. Universal Tilt N Plug Interconnect Box USER'S GUIDE

ACCESSORIES MANUAL PART NUMBER: TNP500. Universal Tilt N Plug Interconnect Box USER'S GUIDE MANUAL PART NUMBER: 400-0091-003 TNP500 Universal Tilt N Plug Interconnect Box USER'S GUIDE INTRODUCTION Your purchase of the TNP100 Tilt N Plug Interconnect Box is greatly appreciated. We are sure you

More information

MICROMASTER Encoder Module

MICROMASTER Encoder Module MICROMASTER Encoder Module Operating Instructions Issue 01/02 User Documentation Foreword Issue 01/02 1 Foreword Qualified Personnel For the purpose of this Instruction Manual and product labels, a Qualified

More information

ACCESSORIES MANUAL PART NUMBER: PRODUCT REVISION: 1 TNP100. Tilt N Plug Interconnect Box USER'S GUIDE

ACCESSORIES MANUAL PART NUMBER: PRODUCT REVISION: 1 TNP100. Tilt N Plug Interconnect Box USER'S GUIDE MANUAL PART NUMBER: 400-0091-001 PRODUCT REVISION: 1 TNP100 Tilt N Plug Interconnect Box USER'S GUIDE INTRODUCTION Your purchase of the TNP100 Tilt N Plug Interconnect Box is greatly appreciated. We are

More information

E6CP-A. An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. Low-cost Encoder with Diameter of 50 mm

E6CP-A. An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. Low-cost Encoder with Diameter of 50 mm Low-cost Encoder with Diameter of 50 mm CSM DS_E An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. High-precision detection of automatic machine timing.

More information

Caution. Hanging the Screen:

Caution. Hanging the Screen: Installation Instructions for Laminar and Laminar XL Projection Screens Caution 1. Read Instructions through completely before proceeding; keep them for future reference. Follow these instructions carefully.

More information

Contents. Instruction Manual T-Rex Page 2 of 16 Release 1.01

Contents. Instruction Manual T-Rex Page 2 of 16 Release 1.01 Contents 1 Safety Precautions... 3 2 Introduction:... 5 3 Theory of Operation... 7 4 Unpacking Procedure... 8 5 Operating TR-Mark III with T-Rex... 9 6 Operating a TR-Mark II with a T-Rex... 13 7 Technical

More information

Kramer Electronics, Ltd. USER MANUAL. Model: VM Video Component Distributor

Kramer Electronics, Ltd. USER MANUAL. Model: VM Video Component Distributor Kramer Electronics, Ltd. USER MANUAL Model: VM-1045 Video Component Distributor Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VM-1045 Video Component Distributor

More information

2100, 2200, 4100, 6200, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors

2100, 2200, 4100, 6200, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors 00, 00, 400, 600, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box 0 975 Cottonwood

More information

Orbit TM DIGITAL SHAKERS

Orbit TM DIGITAL SHAKERS Orbit TM DIGITAL SHAKERS INSTRUCTION MANUAL Models P2, P4, M60, 300, 1000, 1900 Labnet International PO Box 841 Woodbridge, NJ 07095 Phone: 732 417-0700 Fax: 732 417-1750 email: labnet@labnetlink.com 2

More information

INSTRUCTION BOOK FOR. Lectern

INSTRUCTION BOOK FOR. Lectern INSTRUCTION BOOK FOR Lectern Disclaimer Milestone and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

More information

User Guide. Single-Link DVI Active Cable Extender. DVI-7171c

User Guide. Single-Link DVI Active Cable Extender. DVI-7171c User Guide Single-Link DVI Active Cable Extender DVI-7171c TABLE OF CONTENTS SECTION PAGE PRODUCT SAFETY...1 PRODUCT LIABILITY...1 1.0 INTRODUCTION...2 2.0 SPECIFICATIONS...3 3.0 PACKAGE CONTENTS...4 4.0

More information

Operation Manual VMS 3.0 Video System

Operation Manual VMS 3.0 Video System Operation Manual VMS 3.0 Video System for the AlterG Anti-Gravity Treadmill 1 This manual covers operation procedures for the following AlterG products: AlterG Video System model VMS 3.0 NOTE: The following

More information

ALO 030 MKII. 30 Watt DMX LED scanner. User manual

ALO 030 MKII. 30 Watt DMX LED scanner. User manual ALO 030 MKII 30 Watt DMX LED scanner User manual Safety instructions WARNING! Always keep this device away from moisture and rain! Hazardous electrical shocks may occur! WARNING! Only connect this device

More information

SDC-500 Digital Optical Chopper Operating Instructions

SDC-500 Digital Optical Chopper Operating Instructions SDC-500 Digital Optical Chopper Operating Instructions Gentec-EO USA, Inc. 5825 Jean Road Lake Oswego, OR 97035 Phone: 503-697-1870 Fax: 503-697-0633 ddooley@gentec-eo.com www.gentec-eo.com SDC-500 Manual

More information

SATRI AMPLIFIER AMP-51R. Owner s Manual

SATRI AMPLIFIER AMP-51R. Owner s Manual SATRI AMPLIFIER AMP-51R Owner s Manual contents SAFETY INSTRUCTIONS 4 INTRODUCTION 6 OVERVIEW (FRONT PANEL) 8 OVERVIEW (REAR PANEL) 9 OVERVIEW (REMOTE CONTROL) 1 1 OPERATION 12 TROUBLESHOOTING 13 SPECIFICATION

More information

K Service Source. Macintosh Color Display

K Service Source. Macintosh Color Display K Service Source Macintosh Color Display K Service Source Specifications Macintosh Color Display Specifications Characteristics - 1 Characteristics Picture Tube 14-in. diagonal (11.5-in. viewable image)

More information

LED Thunder S-150 Code 1097

LED Thunder S-150 Code 1097 LED Thunder S-150 Code 1097 User Manual 1 1 SAFETY INSTRUCTIONS This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely

More information

User Guide. HDMI Active Cable Extender. DVI-7370c

User Guide. HDMI Active Cable Extender. DVI-7370c User Guide HDMI Active Cable Extender DVI-7370c TABLE OF CONTENTS SECTION PAGE PRODUCT SAFETY...1 PRODUCT LIABILITY STATEMENT........................ 1 1.0 INTRODUCTION...2 2.0 SPECIFICATIONS...3 3.0 PACKAGE

More information

SCALE & WEIGHT DISPLAYS

SCALE & WEIGHT DISPLAYS The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters

More information

2100/2200/4100/6200 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors

2100/2200/4100/6200 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors 00/00/400/600 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box

More information

VT VGA TFT NEMA 4/12 Flat Panel Monitor. User s Guide

VT VGA TFT NEMA 4/12 Flat Panel Monitor. User s Guide VT1040 10.4 VGA TFT NEMA 4/12 Flat Panel Monitor User s Guide 301040(A) (was document no. 920A0001 version 1.1), revised 01/98 Viewtronix Viewtronix reserves the right to make changes in specifications

More information

Hotplate/Stirrers. Performance, Selection, Control

Hotplate/Stirrers. Performance, Selection, Control Hotplate/Stirrers Performance, Selection, Control Professional Hotplates, Stirrers and Hotplate/Stirrers Display for speed, temperature, and time External temperature probe Electronic stir brake Safety

More information

PSM-003. Micro Polarization Controller/Scrambler. User Guide

PSM-003. Micro Polarization Controller/Scrambler. User Guide PSM-003 Micro Polarization Controller/Scrambler User Guide Version: 1.0 Date: August 23, 2012 General Photonics, Incorporated is located in Chino California. For more information visit the company's website

More information

MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz

MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO

More information

Absolute Rotary Encoder E6CP

Absolute Rotary Encoder E6CP Absolute Rotary Encoder Absolute Rotary Encoders with Gray Code Output Gray code output decreases output errors Lightweight plastic housing Used with Omron s H8PS Cam Positioner, this encoder detects the

More information

MS2540 Current Loop Receiver with RS485 Communication

MS2540 Current Loop Receiver with RS485 Communication MS2540 Current Loop Receiver with RS485 Communication User Manual Metal Samples Company A Division of Alabama Specialty Products, Inc. 152 Metal Samples Rd., Munford, AL 36268 Phone: (256) 358 4202 Fax:

More information

INSTRUCTION BOOK FOR. Lectern

INSTRUCTION BOOK FOR. Lectern INSTRUCTION BOOK FOR Lectern All Models Connect power supply to 110/120 VAC 3-wire outlet (220/240 VAC models to 220/240 VAC source). Optional Height Adjustment Models with optional reading surface adjustment

More information

MODELS USIX-024 AND USIX-120 INSTRUCTION SHEET FOR FEDERAL SIGNAL UNISTAT STATUS INDICATOR MODEL USIX

MODELS USIX-024 AND USIX-120 INSTRUCTION SHEET FOR FEDERAL SIGNAL UNISTAT STATUS INDICATOR MODEL USIX 2562089B REV. B 110 Printed in U.S.A. MODELS USIX-024 AND USIX-120 INSTRUCTION SHEET FOR FEDERAL SIGNAL UNISTAT STATUS INDICATOR MODEL USIX Address all communications and shipments to: FEDERAL SIGNAL CORPORATION

More information

Design and Manufacture of Video Pipeline Inspection Systems A Full Service Company

Design and Manufacture of Video Pipeline Inspection Systems A Full Service Company Design and Manufacture of Video Pipeline Inspection Systems A Full Service Company www.rstechserv.com 1315 Controller OPERATIONS MANUAL Made in the USA Table Of Contents: Page 3 Page 5 Page 6 Page 7 Page

More information

PLL1920M LED LCD Monitor

PLL1920M LED LCD Monitor PLL1920M LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Installation...6

More information

VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies

VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies VHF: 54-216 MHz UHF: 470-698 MHz FM: 87.9-107.9 MHz Voltage Input: AC110-120V / AC220-240V Working:

More information

AE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT

AE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT FN: 341MAN1.DOC AE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT DESCRIPTION AE Series Process Indicators are available with 1", 2.3", 4", 8", or 12" high digits,

More information

CNK221/241/261/321/341/361 Cable-Nook Jr. User s Guide

CNK221/241/261/321/341/361 Cable-Nook Jr. User s Guide Cable-Nook Jr. Welcome! We greatly appreciate your purchase of the Cable-Nook Jr. Interconnect Box. We are sure you will find it reliable and simple to use. Superior performance for the right price, backed

More information

TUSKIN Equipment Corporation

TUSKIN Equipment Corporation TUSKIN Equipment Corporation TC-101 Liquid Color Metering System Operation & Maintenance Manual Warning: Read instructions carefully before attempting to install, operate or service the Tuskin Metering

More information

TRF STEP-DOWN TRANSFORMER USER MANUAL

TRF STEP-DOWN TRANSFORMER USER MANUAL TRF STEP-DOWN TRANSFORMER USER MANUA www.ventilation-system.com 2013 ! WARNING The present operation manual consisting of the technical details, operating instructions and technical specification applies

More information

Safety Information. Camera System. If you back up while looking only at the monitor, you may cause damage or injury. Always back up slowly.

Safety Information. Camera System. If you back up while looking only at the monitor, you may cause damage or injury. Always back up slowly. Table of Contents Introduction...3 Safety Information...4-6 Before Beginning Installation...7 Installation Guide...8 Wiring Camera & Monitor...9-10 Replacement Installation Diagram...11 Clip-On Installation

More information

USER MANUAL. 27" 2K QHD LED Monitor L27HAS2K

USER MANUAL. 27 2K QHD LED Monitor L27HAS2K USER MANUAL 27" 2K QHD LED Monitor L27HAS2K TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Troubleshooting 6 Safety Info & FCC warning 1 GETTING

More information

SV-LCD50. Installation and User Guide. Thin-Film Transistor (TFT) Liquid Crystal Display (LCD) Color Rear Vision Monitor. Version 1.

SV-LCD50. Installation and User Guide. Thin-Film Transistor (TFT) Liquid Crystal Display (LCD) Color Rear Vision Monitor. Version 1. SV-LCD50 Installation and User Guide Thin-Film Transistor (TFT) Liquid Crystal Display (LCD) Color Rear Vision Monitor Version 1.00 August 2004 SV-LCD50 Installation and User Guide TFT LCD Color Rear Vision

More information

In-Ceiling Electric Motorized Front Projection Screen Evanesce Series. User s Guide

In-Ceiling Electric Motorized Front Projection Screen Evanesce Series. User s Guide In-Ceiling Electric Motorized Front Projection Screen Evanesce Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The

More information

.Power Distribution Center. PD-1. Instruction Manual

.Power Distribution Center. PD-1. Instruction Manual .Power Distribution Center. PD-1 Instruction Manual www.datavideo-tek.com 1 Contents Warnings and Precautions... 3 Warranty... 4 Standard Warranty... 4 Two Year Warranty... 4 Disposal... 4 Packing List...

More information

ModWright Instruments, Inc. PH 150 Tube Phono Stage Owner s Manual

ModWright Instruments, Inc. PH 150 Tube Phono Stage Owner s Manual ModWright Instruments, Inc. PH 150 Tube Phono Stage Owner s Manual Manufactured by ModWright Instruments, Inc. 21919 399th St., Amboy, WA 98601 USA www.modwright.com 1 CAUTIONS: Do not operate or power

More information

MonoBright LED DAYLIGHT 750

MonoBright LED DAYLIGHT 750 MonoBright LED DAYLIGHT 750 USER MANUAL MonoBright LED Daylight 750 - USER MANUAL 1 MonoBright LED DAYLIGHT 750 INTRODUCTION Thank you for choosing Genaray. The Genaray MonoBright LED Daylight 750 incorporates

More information

AUTOMATIC TAPING MACHINE INSTRUCTION MANUAL TAIYO SEIKI CO., LTD.

AUTOMATIC TAPING MACHINE INSTRUCTION MANUAL TAIYO SEIKI CO., LTD. - AUTOMATIC TAPING MACHINE INSTRUCTION MANUAL TAIYO SEIKI CO., LTD. 1 Contents CONTENTS 1. Introduction... 2 1-1. Important safety notice...2 1-2. Precautions for use and installation...2 1-3. Operating

More information

Noise Detector ND-1 Operating Manual

Noise Detector ND-1 Operating Manual Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation

More information

Weekly Timer. Mounting track 50 cm (1.64 ft) length PFP-50N 1 m (3.28 ft) length PFP-100N

Weekly Timer. Mounting track 50 cm (1.64 ft) length PFP-50N 1 m (3.28 ft) length PFP-100N Weekly Timer 1/4 DIN Size Timer Features Prompted Programming and Large LCD Display 24 hours x 7 days programming using just 5 switches 16 program steps and cycle operation Two independent 15 A control

More information

MonoBright LED DAYLIGHT 1200

MonoBright LED DAYLIGHT 1200 MonoBright LED DAYLIGHT 1200 USER MANUAL MonoBright LED Daylight 1200 - USER MANUAL 1 MonoBright LED DAYLIGHT 1200 INTRODUCTION Thank you for choosing Genaray. The Genaray MonoBright LED 1200 incorporates

More information

Three Axis Digital Readout System

Three Axis Digital Readout System NEWALL MEASUREMENT SYSTEMS C80 Three Axis Digital Readout System CONTENTS 2 SPECIFICATIONS 3 CONNECTIONS 4 MOUNTING 4 Arm Mounting (Non-adjustable) 4 Arm Mounting (Adjustable) 5 Face Mounting (Adjustable)

More information

SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width

SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system

More information

ORLAND SCAN PR PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, China

ORLAND SCAN PR PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, China ORLAND SCAN PR-1201 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in

More information

OPERATING AND SAFETY INSTRUCTIONS for DIGITAL TEMPERATURE CONTROLS (PLSM SERIES)

OPERATING AND SAFETY INSTRUCTIONS for DIGITAL TEMPERATURE CONTROLS (PLSM SERIES) user instructions 711 HULMAN STREET PO BOX 2128 TERRE HAUTE, IN 47802 812-235-6167 FAX 812-234-6975 OPERATING AND SAFETY INSTRUCTIONS for DIGITAL TEMPERATURE CONTROLS (PLSM SERIES) Models: 104A PLSM112;

More information

TECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L

TECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L TECHNICAL GUIDE TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW

More information

TABLE OF CONTENTS. 1) Introduction 2. 2) Unpacking the Ares 2. 3) Installing the Ares in your system 3. 4) Setting the Operational Parameters 4

TABLE OF CONTENTS. 1) Introduction 2. 2) Unpacking the Ares 2. 3) Installing the Ares in your system 3. 4) Setting the Operational Parameters 4 TABLE OF CONTENTS 1) Introduction 2 2) Unpacking the Ares 2 3) Installing the Ares in your system 3 4) Setting the Operational Parameters 4 5) High Output MM/MC Cartridge Setup 6 6) Medium Output Cartridge

More information

AF-300 E11 Adjustable Frequency Drive

AF-300 E11 Adjustable Frequency Drive AF-300 E11 Adjustable Frequency Drive The AF-300 E11 adjustable frequency drive is GE s new generation of micro drives. GE recognized your need for a high-performance, full-featured compact drive and designed

More information

19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR

19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR 19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR V193/ V220 Series V202 Series USER MANUAL www.viewera.com Rev. 2.0 Table of Contents EMC Compliance......1 Important Precautions...2 1. Package contents....3

More information

E8Y. Micropressure Sensor with Easy-to-Read Digital Display. Differential Pressure Sensor. Ordering Information. Sensors

E8Y. Micropressure Sensor with Easy-to-Read Digital Display. Differential Pressure Sensor. Ordering Information. Sensors Differential Sensor Micropressure Sensor with Easy-to-Read Digital Repeat accuracy of ±1% FS (setting resolution: 0.01 kpa), high-precision pressure control available. Compact design (31 mm) saves mounting

More information

CNK JR. SERIES CABLE-NOOK JR. TABLETOP INTERCONNECT BOXES USER'S GUIDE

CNK JR. SERIES CABLE-NOOK JR. TABLETOP INTERCONNECT BOXES USER'S GUIDE MANUAL PART NUMBER: 400-0133-001 PRODUCT REVISION: 0 CNK JR. SERIES CABLE-NOOK JR. TABLETOP INTERCONNECT BOXES USER'S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL... 2 INSTALLATION...

More information

In-Wall Control Mount for ipod Touch

In-Wall Control Mount for ipod Touch In-Wall Control Mount for ipod Touch INTRODUCTION The Mirage KP-iOS is an in-wall system that allows ipod touch (4th generation) to become a semi-permanent fixture in your wall. The system allows you to

More information

Sphinx II. Owner s Manual. Tube Hybrid Integrated Power Amplifier. Rogue Audio, Inc. 3 Marian Lane Brodheadsville, PA Issue date: 08/01/16

Sphinx II. Owner s Manual. Tube Hybrid Integrated Power Amplifier. Rogue Audio, Inc. 3 Marian Lane Brodheadsville, PA Issue date: 08/01/16 Sphinx II Tube Hybrid Integrated Power Amplifier Owner s Manual Rogue Audio, Inc. 3 Marian Lane Brodheadsville, PA 18322 Issue date: 08/01/16 TABLE OF CONTENTS 1) Introduction 2 2) Unpacking the Sphinx

More information

Figure 1: Standard 906 Sensor and Pulser Disc. Figure 2: Standard 906 Sensor and Pulser Wrap

Figure 1: Standard 906 Sensor and Pulser Disc. Figure 2: Standard 906 Sensor and Pulser Wrap Description: The TR5000 is a Full Logic Control Process ratemeter that can display up to three separate values of rate and compare them to programmable set points. Rates A & B can be programmed by the

More information

SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width

SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system must be used

More information

MY-HITE ADJUSTABLE TABLE

MY-HITE ADJUSTABLE TABLE MY-HITE ADJUSTABLE TABLE Corner T Leg Base Model Number : FCNAHBT Please Read Instructions Before Use ASSEMBLY INSTRUCTIONS ALL WORKSTYLES WELCOME Thank you for choosing Friant. We appreciate the trust

More information

PNP300 / PNP300UN / PNP350

PNP300 / PNP300UN / PNP350 DOCUMENT NUMBER 400-0114-003 / UN / PNP350 Pop N Plug Slim INTERCONNECT BOX USER'S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS...2 GENERAL...2 INSTALLATION...2 CLEANING...2 ABOUT YOUR /300UN/350...3

More information

ELECTRICAL. DATA AND INDEX Not all complements shown A shown for reference. Index A leads B, CW (from shaft end) TERMINAL CONNECTIONS COM VCC CASE

ELECTRICAL. DATA AND INDEX Not all complements shown A shown for reference. Index A leads B, CW (from shaft end) TERMINAL CONNECTIONS COM VCC CASE NorthStar brand SERIES HD35R Heavy Duty Encoder Key Features Phased Array Sensor for Reliable Signal Output Rugged Design with Wide-Spaced Oversized Bearings Unbreakable Code Disc up to 5000PPR Improved

More information

Operating Instructions 07/2007 Edition. SINAMICS G130/G150 Line harmonics filter. sinamics

Operating Instructions 07/2007 Edition. SINAMICS G130/G150 Line harmonics filter. sinamics Operating Instructions 07/2007 Edition SINAMICS G130/G150 Line harmonics filter sinamics s Safety information 1 General 2 SINAMICS SINAMICS G130/G150 Operating Instructions Mechanical installation 3 Electrical

More information

WINEGARD INSTALLATION MANUAL. Model GM Carryout Ladder Mount for mounting pipes with outer diameters between 1 to 1-1/8

WINEGARD INSTALLATION MANUAL. Model GM Carryout Ladder Mount for mounting pipes with outer diameters between 1 to 1-1/8 WINEGARD INSTALLATION MANUAL Model GM-3000 Carryout Ladder Mount for mounting pipes with outer diameters between 1 to 1-1/8 WARNING: DO NOT USE THE LADDER MOUNT AS A STEP! NOT INTENDED FOR USE WITH THE

More information

User Manual. Adjustable Speed Vortex. Fixed Speed Vortex

User Manual. Adjustable Speed Vortex. Fixed Speed Vortex User Manual MX-S MX-F Adjustable Speed Vortex Fixed Speed Vortex Please read the User Manual carefully before use, and follow all operating and safety instructions! Technical specifications and outline

More information

SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS... 4 RECOMMENDED TOOLS... 6 CONTROL PANEL OVERVIEW...

SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS... 4 RECOMMENDED TOOLS... 6 CONTROL PANEL OVERVIEW... CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS... 4 RECOMMENDED TOOLS... 6 CONTROL PANEL OVERVIEW... 6 ASSEMBLY... 7 SYSTEM RESET... 11 OPERATION...

More information

Instructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16)

Instructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16) Satellite multiswitch Instructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16) EMP-CENTAURI is a registered trademark Dear Customer, Thank you for buying the EMP-Centauri

More information

PXL2470MW LED LCD Monitor

PXL2470MW LED LCD Monitor PXL2470MW LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Unpacking Instructions...2 Safety Precautions...2 Package Overview...3 First Setup...4 Front View of the Product...5

More information

PLL2710W LED LCD Monitor

PLL2710W LED LCD Monitor PLL2710W LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 Package Overview...3 First Setup...4 Front View of the Product...5 Rear View of the Product...6

More information

CNK221 CABLE-NOOK JR. INTERCONNECT BOX USER S GUIDE

CNK221 CABLE-NOOK JR. INTERCONNECT BOX USER S GUIDE MANUAL PART NUMBER: 400-0133-002 CNK221 CABLE-NOOK JR. INTERCONNECT BOX USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL... 2 INSTALLATION... 2 CLEANING... 2 FCC / CE NOTICE...

More information

User s Manual. Digital Media Converter Package Part #: DL-HDCAT-WP

User s Manual. Digital Media Converter Package Part #: DL-HDCAT-WP User s Manual Digital Media Converter Package Part #: DL-HDCAT-WP TABLE OF CONTENTS 1-1 Table of Contents 1-2 Welcome and Safety Notes 1-3 Product Description and General Specifications 1-4 Environmental

More information

Website: Tel: ADDRESS: 6475 Las Positas Rd. Livermore, CA Item No. E5B/E5S Installation Guide

Website:   Tel: ADDRESS: 6475 Las Positas Rd. Livermore, CA Item No. E5B/E5S Installation Guide Website: www.flexispot.com Tel: -855-4-808 ADDRESS: 6475 Las Positas Rd. Livermore, CA 9455 Item No. E5B/E5S Installation Guide Specifications Step Column 3 Max. Weight Capacity 0 Ibs (00 kg) Speed 38mm/s

More information

Page 1 of 6 FXLD618FRP2I4 LED FIXTURE Version 0.2 OWNERS MANUAL 10/04/17

Page 1 of 6 FXLD618FRP2I4 LED FIXTURE Version 0.2 OWNERS MANUAL 10/04/17 Page 1 of 6 FEATURES AND SPECIFICATIONS LEDS: 18, 6W each (Warm White, Cool White, 2in1) Beam angle: 25º or 45 Control system: DMX512 + Stand Alone Modes DMX channels: 1/2/3/4/5 DMX connectors: 3 pin XLR

More information

PLL2210MW LED Monitor

PLL2210MW LED Monitor PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6

More information

SINAMICS G130 / G150. Line harmonics filter. Operating Instructions 05/2010 SINAMICS

SINAMICS G130 / G150. Line harmonics filter. Operating Instructions 05/2010 SINAMICS SINAMICS G130 / G150 Line harmonics filter Operating Instructions 05/2010 SINAMICS s Safety information 1 General 2 SINAMICS SINAMICS G130 / G150 Operating Instructions Mechanical installation 3 Electrical

More information

LBS-1 (Lowrance Broadband Sounder)

LBS-1 (Lowrance Broadband Sounder) Pub. 988-0170-001 LBS-1 (Lowrance Broadband Sounder) Installation Instructions The LBS-1 is a digital sonar optimizer designed to enhance sonar echo clarity. The broadband sounder was created to deliver

More information

NS-3 RF Noise Source Operation Manual

NS-3 RF Noise Source Operation Manual RF Noise Source Operation Manual Version 2.04 June 3, 2016 SPECIFICATIONS Frequency... Maximum output level... Output flatness... (at max output level) Impedance... Displayed level... Repeatability...

More information

Kramer Electronics, Ltd.

Kramer Electronics, Ltd. Kramer Electronics, Ltd. Preliminary USER MANUAL Model: VM-1110xl Balanced Audio Distributor Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Your VM-1110xl Balanced

More information

General Wiring and Installation Guidelines. Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers

General Wiring and Installation Guidelines. Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers General Wiring and Installation Guidelines Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers Congratulations on your purchase of a Dynapar brand encoder.

More information

Information. Marketing Description. For Models: DA2133i. 2113i. User s Guide Rev B

Information. Marketing Description. For Models: DA2133i. 2113i. User s Guide Rev B Casework Model Number User s Marketing Description Information For Models: xxxx FCC (-001) (All) xxxx FTC (All) (-002) DA2133i 2113i User s Guide 003-1891-00 Rev B Table of Contents Important Information

More information

Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module

Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Helvar Data is subject to change without notice. www.helvar.com i Contents Section Page Introduction 1 Installation 2 1. Attach

More information

Fully ly Automaticti. Motorised Satellite t TV System. User s manual REV

Fully ly Automaticti. Motorised Satellite t TV System. User s manual REV REV. 1.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au

More information

ISE, Inc Royalton Rd. Cleveland, OH USA Tel: (440) Fax: (440) B Long Ranger Timer

ISE, Inc Royalton Rd. Cleveland, OH USA Tel: (440) Fax: (440) B Long Ranger Timer ISE, Inc. 10100 Royalton Rd. Cleveland, OH 44133 USA Tel: (440) 237-3200 Fax: (440) 237-1744 http://instserv.com 365B Long Ranger Timer INSTALLATION INSTRUCTION November, 2000 3-0365-095-04-00 DESCRIPTION:

More information