RYKO Italia s.r.l. V. Casale Morano Po (Al) t f

Size: px
Start display at page:

Download "RYKO Italia s.r.l. V. Casale Morano Po (Al) t f"

Transcription

1 Italia RYKO Italia s.r.l. V. Casale Morano Po (Al) t f June 30, 2003 ITALIA SERVICE BULLETIN - # VFD parameter settings for conveyor equipment with Mitsubishi PLC MACHINES AFFECTED: Mini Vista, Vista, Vista Plus, and Super Vista conveyor equipment with a Mitsubishi PLC. PROBLEM: Field does not have the parameter settings required for proper operation of the Mitsubishi Variable Frequency Drives. SOLUTION: Refer to the following pages that contain the parameter settings and the procedure to enter the parameter settings. The VFD parameters that need to be changed are highlighted in the Operational setting column. All other parameters remain at the factory setting. ADDITIONAL INFORMATION: Do not use these parameters settings for conveyor equipment with an Omron PLC. See Italia service bulletin for the parameter settings for conveyor equipment with an Omron PLC.

2 Procedure for changing parameter settings with a Mitsubishi FR-S Press the PU/EXT key. Observe the PU light on the display turn ON. 2. Press the MODE key to enter the parameter setting mode. Observe P 0 on the display. 3. Turn the setting dial until the desired parameter number appears on the display. Example: P 7 4. Once the parameter to be changed is on the display, press the SET key. This displays the current value set for that parameter. Example: Turn the setting dial until the desired value appears on the display. Example: Press the SET key to set the value. Observe 10.0 and P 7 flicker on the display indicating the parameter write is successful. By turning the setting dial, other parameters may be viewed. To change, proceed from step #5 as listed above. By pressing the SET key twice, it will automatically advance to the next parameter. FR-S520 VFD Operational Panel RUN indicator indicates operation when lit PU/EXT key use to switch between PU and external operation mode. 3 digit monitor LED PU indicator indicates PU operation mode EXT indicator indicates external operation mode _ + RUN PU EXT PU EXT RUN STOP RESET RUN key used to give a manual forward rotation command STOP/ RESET key Used to stop an operation or reset an alarm. MODE SET Setting dial MODE key use to change the setting mode SET key use to define each setting

3 CONVEYOR MINI VISTA, VISTA AND VISTA PLUS Mitsubishi VFD FR-S520S 1.5 kw Parameter Function description Factory setting Operational setting P0 Torque boost 6 % 5 P1 Maximum frequency * Hz 70 P2 Minimum frequency 0 Hz 50 P3 Base frequency * Hz P4 Speed setting (high) * Hz 70 P5 Speed setting (middle) 30 Hz P6 Speed setting (low) 10 Hz 70 P7 Acceleration time 5 sec. 0.5 P8 Deceleration time 5 sec. 0.3 P9 Electronic thermal O/L relay ** Rated current 4.5 P10 DC brake operation frequency 3 Hz P11 DC brake operation time 0.5 sec P12 DC brake voltage 6 % P13 Starting frequency 0.5 Hz P14 Load pattern selection 0 P15 Jog frequency 5 Hz P16 Jog accel/decel time 0.5 sec. P17 RUN rotation selection 0 P18 P19 Base frequency voltage P20 Accel/decel reference freq. * Hz P21 Stall prevent function select 0 P22 Stall prevent operate level 150 % P23 Double speed stall prevent --- P24 Speed setting (4) --- P25 Speed setting (5) --- P26 Speed setting (6) --- P27 Speed setting (7) --- P28 Stall prevent reduction freq. * Hz P29 Accel/decel pattern 0 P30 Ext. function display select 0 P31 Frequency jump 1A --- P32 Frequency jump 1B --- P33 Frequency jump 2A --- P34 Frequency jump 2B --- P35 Frequency jump 3A --- P36 Frequency jump 3B --- P37 Speed display 0 P38 Frequency voltage gain * Hz P39 Frequency current gain * Hz

4 P40 Start time ground fault * 1-0 P41 Frequency sensitivity 10 % P42 Output frequency detect 6 Hz P43 Output freq. Reverse --- P44 Second accel/decel time 5 sec. P45 Second deceleration time --- P46 Second torque boost --- P47 Second V/F --- P48 Output current level detect 150 % P49 Output current detect delay time 0 sec. P50 Zero current detect level 5 % P51 Zero current detect time 0.5 sec. P52 Control panel display data 0 P53 Frequency set selection 0 P54 FM terminal function select 0 P55 Frequency monitor reference * Hz 60 P56 Current monitor reference ** Rated current P57 Restart coasting time --- P58 Restart cushion time 1 sec. P59 Remote set function select 0 P60 RL terminal function select 0 P61 RM terminal function select 1 P62 RH terminal function select 2 P63 STR terminal function select --- P64 RUN terminal function select 0 P65 A,B,C terminal function select P66 Retry selection 0 1 P67 Number of retry at alarm 0 1 P68 Retry wait time 1 sec. 2.5 P69 Retry display erase 0 P70 Soft-PWM setting 1 P71 Applied motor 0 P72 PWM frequency select 1 P73 0-5/0-10V select 0 P74 Input filter time constant 1 P75 Reset select 14 P76 Cooling fan operate select 1 P77 Parameter write disable select 0 P78 Reverse rotate select 0 P79 Operation mode select 0 2 * Factory setting determined by EC or non-ec unit. ** The rated current depends on the VFD capacity, either 1.5 kw or.37 kw.

5 CONVEYOR SUPERVISTA Mitsubishi VFD FR-S520S 1.5 kw Parameter Function description Factory setting Operational setting P0 Torque boost 6 % 5 P1 Maximum frequency * Hz 90 P2 Minimum frequency 0 Hz 50 P3 Base frequency * Hz P4 Speed setting (high) * Hz 70 P5 Speed setting (middle) 30 Hz 90 P6 Speed setting (low) 10 Hz 70 P7 Acceleration time 5 sec. 1 P8 Deceleration time 5 sec. 0.3 P9 Electronic thermal O/L relay **Rated 5.5 current P10 DC brake operation frequency 3 Hz P11 DC brake operation time 0.5 sec P12 DC brake voltage 6 % P13 Starting frequency 0.5 Hz P14 Load pattern selection 0 P15 Jog frequency 5 Hz P16 Jog accel/decel time 0.5 sec. P17 RUN rotation selection 0 P18 P19 Base frequency voltage P20 Accel/decel reference freq. * Hz P21 Stall prevent function select 0 P22 Stall prevent operate level 150 % P23 Double speed stall prevent --- P24 Speed setting (4) --- P25 Speed setting (5) --- P26 Speed setting (6) --- P27 Speed setting (7) --- P28 Stall prevent reduction freq. * Hz P29 Accel/decel pattern 0 P30 Ext. function display select 0 P31 Frequency jump 1A --- P32 Frequency jump 1B --- P33 Frequency jump 2A --- P34 Frequency jump 2B --- P35 Frequency jump 3A --- P36 Frequency jump 3B --- P37 Speed display 0 P38 Frequency voltage gain * Hz P39 Frequency current gain * Hz

6 P40 Start time ground fault * 1-0 P41 Frequency sensitivity 10 % P42 Output frequency detect 6 Hz P43 Output freq. Reverse --- P44 Second accel/decel time 5 sec. P45 Second deceleration time --- P46 Second torque boost --- P47 Second V/F --- P48 Output current level detect 150 % P49 Output current detect delay time 0 sec. P50 Zero current detect level 5 % P51 Zero current detect time 0.5 sec. P52 Control panel display data 0 P53 Frequency set selection 0 P54 FM terminal function select 0 P55 Frequency monitor reference * Hz 60 P56 Current monitor reference ** Rated current P57 Restart coasting time --- P58 Restart cushion time 1 sec. P59 Remote set function select 0 P60 RL terminal function select 0 P61 RM terminal function select 1 P62 RH terminal function select 2 P63 STR terminal function select --- P64 RUN terminal function select 0 P65 A,B,C terminal function select P66 Retry selection 0 1 P67 Number of retry at alarm 0 1 P68 Retry wait time 1 sec. 2.5 P69 Retry display erase 0 P70 Soft-PWM setting 1 P71 Applied motor 0 P72 PWM frequency select 1 P73 0-5/0-10V select 0 P74 Input filter time constant 1 P75 Reset select 14 P76 Cooling fan operate select 1 P77 Parameter write disable select 0 P78 Reverse rotate select 0 P79 Operation mode select 0 2 * Factory setting determined by EC or non-ec unit. ** The rated current depends on the VFD capacity, either 1.5 kw or.37 kw.

7 TOP HYDROBOT LIFT AND DESCEND - MINI VISTA, VISTA PLUS, VISTA AND SUPERVISTA Mitsubishi VFD FR-S kw Parameter Function de scription Factory setting Operational setting P0 Torque boost 6 % 5 P1 Maximum frequency * Hz 60 P2 Minimum frequency 0 Hz 50 P3 Base frequency * Hz P4 Speed setting (high) * Hz 60 P5 Speed setting (middle) 30 Hz 60 P6 Speed setting (low) 10 Hz 50 P7 Acceleration time 5 sec. 0.8 P8 Deceleration time 5 sec. 0.3 P9 Electronic thermal O/L relay **Rated 1.9 current P10 DC brake operation frequency 3 Hz P11 DC brake operation time 0.5 sec P12 DC brake voltage 6 % P13 Starting frequency 0.5 Hz P14 Load pattern selection 0 P15 Jog frequency 5 Hz P16 Jog accel/decel time 0.5 sec. P17 RUN rotation selection 0 P18 P19 Base frequency voltage P20 Accel/decel reference freq. * Hz 60 P21 Stall prevent function select 0 P22 Stall prevent operate level 150 % P23 Double speed stall prevent --- P24 Speed setting (4) --- P25 Speed setting (5) --- P26 Speed setting (6) --- P27 Speed setting (7) --- P28 Stall prevent reduction freq. * Hz P29 Accel/decel pattern 0 P30 Ext. function display select 0 P31 Frequency jump 1A --- P32 Frequency jump 1B --- P33 Frequency jump 2A --- P34 Frequency jump 2B --- P35 Frequency jump 3A --- P36 Frequency jump 3B --- P37 Speed display 0 P38 Frequency voltage gain * Hz P39 Frequency current gain * Hz

8 P40 Start time ground fault * 1-0 P41 Frequency sensitivity 10 % P42 Output frequency detect 6 Hz P43 Output freq. Reverse --- P44 Second accel/decel time 5 sec. P45 Second deceleration time --- P46 Second torque boost --- P47 Second V/F --- P48 Output current level detect 150 % P49 Output current detect delay time 0 sec. P50 Zero current detect level 5 % P51 Zero current detect time 0.5 sec. P52 Control panel display data 0 P53 Frequency set selection 0 P54 FM terminal function select 0 P55 Frequency monitor reference * Hz 60 P56 Current monitor reference ** Rated current P57 Restart coasting time --- P58 Restart cushion time 1 sec. P59 Remote set function select 0 P60 RL terminal function select 0 P61 RM terminal function select 1 P62 RH terminal function select 2 P63 STR terminal function select --- P64 RUN terminal function select 0 P65 A,B,C terminal function select P66 Retry selection 0 1 P67 Number of retry at alarm 0 1 P68 Retry wait time 1 sec. 2.5 P69 Retry display erase 0 P70 Soft-PWM setting 1 P71 Applied motor 0 P72 PWM frequency select 1 P73 0-5/0-10V select 0 P74 Input filter time constant 1 P75 Reset select 14 P76 Cooling fan operate select 1 P77 Parameter write disable select 0 P78 Reverse rotate select 0 P79 Operation mode select 0 2 * Factory setting determined by EC or non-ec unit. ** The rated current depends on the VFD capacity, either 1.5 kw or.37 kw.

9 TOP HYDROBOT ROTATION MINI VISTA, VISTA PLUS, VISTA AND SUPERVISTA Mitsubishi VFD FR-S kw Parameter Function description Factory setting Operational setting P0 Torque boost 6 % 5 P1 Maximum frequency * Hz 50 P2 Minimum frequency 0 Hz 25 P3 Base frequency * Hz P4 Speed setting (high) * Hz 50 P5 Speed setting (middle) 30 Hz 50 P6 Speed setting (low) 10 Hz 50 P7 Acceleration time 5 sec. 0.5 P8 Deceleration time 5 sec. 0.5 P9 Electronic thermal O/L relay **Rated 1.9 current P10 DC brake operation frequency 3 Hz P11 DC brake operation time 0.5 sec P12 DC brake voltage 6 % P13 Starting frequency 0.5 Hz P14 Load pattern selection 0 P15 Jog frequency 5 Hz P16 Jog accel/decel time 0.5 sec. P17 RUN rotation selection 0 P18 P19 Base frequency voltage P20 Accel/decel reference freq. * Hz 60 P21 Stall prevent function select 0 P22 Stall prevent operate level 150 % P23 Double speed stall prevent --- P24 Speed setting (4) --- P25 Speed setting (5) --- P26 Speed setting (6) --- P27 Speed setting (7) --- P28 Stall prevent reduction freq. * Hz P29 Accel/decel pattern 0 P30 Ext. function display select 0 P31 Frequency jump 1A --- P32 Frequency jump 1B --- P33 Frequency jump 2A --- P34 Frequency jump 2B --- P35 Frequency jump 3A --- P36 Frequency jump 3B --- P37 Speed display 0 P38 Frequency voltage gain * Hz P39 Frequency current gain * Hz

10 P40 Start time ground fault * 1-0 P41 Frequency sensitivity 10 % P42 Output frequency detect 6 Hz P43 Output freq. Reverse --- P44 Second accel/decel time 5 sec. P45 Second deceleration time --- P46 Second torque boost --- P47 Second V/F --- P48 Output current level detect 150 % P49 Output current detect delay time 0 sec. P50 Zero current detect level 5 % P51 Zero current detect time 0.5 sec. P52 Control panel display data 0 P53 Frequency set selection 0 P54 FM terminal function select 0 P55 Frequency monitor reference * Hz 60 P56 Current monitor reference ** Rated current P57 Restart coasting time --- P58 Restart cushion time 1 sec. P59 Remote set function select 0 P60 RL terminal function select 0 P61 RM terminal function select 1 P62 RH terminal function select 2 P63 STR terminal function select --- P64 RUN terminal function select 0 P65 A,B,C terminal function select P66 Retry selection 0 1 P67 Number of retry at alarm 0 1 P68 Retry wait time 1 sec. 2.5 P69 Retry display erase 0 P70 Soft-PWM setting 1 P71 Applied motor 0 P72 PWM frequency select 1 P73 0-5/0-10V select 0 P74 Input filter time constant 1 P75 Reset select 14 P76 Cooling fan operate select 1 P77 Parameter write disable select 0 P78 Reverse rotate select 0 P79 Operation mode select 0 2 * Factory setting determined by EC or non-ec unit. ** The rated current depends on the VFD capacity, either 1.5 kw or.37 kw.

11 TOP DRYER LIFT AND DESCEND - MINI VISTA, VISTA PLUS, VISTA AND SUPERVISTA Mitsubishi VFD FR-S kw Parameter Function description Factory setting Operational setting P0 Torque boost 6 % 5 P1 Maximum frequency * Hz 60 P2 Minimum frequency 0 Hz 50 P3 Base frequency * Hz P4 Speed setting (high) * Hz 60 P5 Speed setting (middle) 30 Hz 50 P6 Speed setting (low) 10 Hz 50 P7 Acceleration time 5 sec. 0.8 P8 Deceleration time 5 sec. 0.3 P9 Electronic thermal O/L relay **Rated 1.9 current P10 DC brake operation frequency 3 Hz P11 DC brake operation time 0.5 sec P12 DC brake voltage 6 % P13 Starting frequency 0.5 Hz P14 Load pattern selection 0 P15 Jog frequency 5 Hz P16 Jog accel/decel time 0.5 sec. P17 RUN rotation selection 0 P18 P19 Base frequency voltage P20 Accel/decel reference freq. * Hz 60 P21 Stall prevent function select 0 P22 Stall prevent operate level 150 % P23 Double speed stall prevent --- P24 Speed setting (4) --- P25 Speed setting (5) --- P26 Speed setting (6) --- P27 Speed setting (7) --- P28 Stall prevent reduction freq. * Hz P29 Accel/decel pattern 0 P30 Ext. function display select 0 P31 Frequency jump 1A --- P32 Frequency jump 1B --- P33 Frequency jump 2A --- P34 Frequency jump 2B --- P35 Frequency jump 3A --- P36 Frequency jump 3B --- P37 Speed display 0 P38 Frequency voltage gain * Hz P39 Frequency current gain * Hz

12 P40 Start time ground fault * 1-0 P41 Frequency sensitivity 10 % P42 Output frequency detect 6 Hz P43 Output freq. Reverse --- P44 Second accel/decel time 5 sec. P45 Second deceleration time --- P46 Second torque boost --- P47 Second V/F --- P48 Output current level detect 150 % P49 Output current detect delay time 0 sec. P50 Zero current detect level 5 % P51 Zero current detect time 0.5 sec. P52 Control panel display data 0 P53 Frequency set selection 0 P54 FM terminal function select 0 P55 Frequency monitor reference * Hz 60 P56 Current monitor reference ** Rated current P57 Restart coasting time --- P58 Restart cushion time 1 sec. P59 Remote set function select 0 P60 RL terminal function select 0 P61 RM terminal function select 1 P62 RH terminal function select 2 P63 STR terminal function select --- P64 RUN terminal function select 0 P65 A,B,C terminal function select P66 Retry selection 0 1 P67 Number of retry at alarm 0 1 P68 Retry wait time 1 sec. 2.5 P69 Retry display erase 0 P70 Soft-PWM setting 1 P71 Applied motor 0 P72 PWM frequency select 1 P73 0-5/0-10V select 0 P74 Input filter time constant 1 P75 Reset select 14 P76 Cooling fan operate select 1 P77 Parameter write disable select 0 P78 Reverse rotate select 0 P79 Operation mode select 0 2 * Factory setting determined by EC or non-ec unit. ** The rated current depends on the VFD capacity, either 1.5 kw or.37 kw.

13 VERTICAL FOLLOWING SIDE BRUSH CART - SUPERVISTA Mitsubishi VFD FR-S kw Parameter Function description Factory setting Operational setting P0 Torque boost 6 % 5 P1 Maximum frequency * Hz 80 P2 Minimum frequency 0 Hz 30 P3 Base frequency * Hz P4 Speed setting (high) * Hz 50 P5 Speed setting (middle) 30 Hz 45 P6 Speed setting (low) 10 Hz 40 P7 Acceleration time 5 sec. 0.6 P8 Deceleration time 5 sec. 0.3 P9 Electronic thermal O/L relay **Rated 1.9 current P10 DC brake operation frequency 3 Hz P11 DC brake operation time 0.5 sec P12 DC brake voltage 6 % P13 Starting frequency 0.5 Hz P14 Load pattern selection 0 P15 Jog frequency 5 Hz P16 Jog accel/decel time 0.5 sec. P17 RUN rotation selection 0 P18 P19 Base frequency voltage P20 Accel/decel reference freq. * Hz 60 P21 Stall prevent function select 0 P22 Stall prevent operate level 150 % P23 Double speed stall prevent --- P24 Speed setting (4) --- P25 Speed setting (5) --- P26 Speed setting (6) --- P27 Speed setting (7) --- P28 Stall prevent reduction freq. * Hz P29 Accel/decel pattern 0 P30 Ext. function display select 0 P31 Frequency jump 1A --- P32 Frequency jump 1B --- P33 Frequency jump 2A --- P34 Frequency jump 2B --- P35 Frequency jump 3A --- P36 Frequency jump 3B --- P37 Speed display 0 P38 Frequency voltage gain * Hz P39 Frequency current gain * Hz

14 P40 Start time ground fault * 1-0 P41 Frequency sensitivity 10 % P42 Output frequency detect 6 Hz P43 Output freq. Reverse --- P44 Second accel/decel time 5 sec. 6 P45 Second deceleration time --- P46 Second torque boost --- P47 Second V/F --- P48 Output current level detect 150 % P49 Output current detect delay time 0 sec. P50 Zero current detect level 5 % P51 Zero current detect time 0.5 sec. P52 Control panel display data 0 P53 Frequency set selection 0 P54 FM terminal function select 0 P55 Frequency monitor reference * Hz 60 P56 Current monitor reference ** Rated current P57 Restart coasting time --- P58 Restart cushion time 1 sec. P59 Remote set function select 0 P60 RL terminal function select 0 P61 RM terminal function select 1 P62 RH terminal function select 2 P63 STR terminal function select --- P64 RUN terminal function select 0 P65 A,B,C terminal function select P66 Retry selection 0 1 P67 Number of retry at alarm 0 1 P68 Retry wait time 1 sec. 2.5 P69 Retry display erase 0 P70 Soft-PWM setting 1 P71 Applied motor 0 P72 PWM frequency select 1 P73 0-5/0-10V select 0 P74 Input filter time constant 1 P75 Reset select 14 P76 Cooling fan operate select 1 P77 Parameter write disable select 0 P78 Reverse rotate select 0 P79 Operation mode select 0 2 * Factory setting determined by EC or non-ec unit. The EC setting is shown first. ** The rated current depends on the VFD capacity, either 1.5 kw or.37 kw.

AF-300 E11 Adjustable Frequency Drive

AF-300 E11 Adjustable Frequency Drive AF-300 E11 Adjustable Frequency Drive The AF-300 E11 adjustable frequency drive is GE s new generation of micro drives. GE recognized your need for a high-performance, full-featured compact drive and designed

More information

For applications from 0.25 to 5 HP, the MD60 is a simple AC Microdrive that can be panel mounted as well as wall or machine mounted.

For applications from 0.25 to 5 HP, the MD60 is a simple AC Microdrive that can be panel mounted as well as wall or machine mounted. For applications from 0.25 to 5 HP, the MD60 is a simple AC Microdrive that can be panel mounted as well as wall or machine mounted. N223 Reliance Electric s MD60 AC Drive is ready to operate out-of-the-box!

More information

ADJUSTABLE SPEED DRIVES. nc1 Drive

ADJUSTABLE SPEED DRIVES. nc1 Drive ADJUSTABLE SPEED DRIVES nc1 Drive Ultra-Compact Sub-Micro Drive The nc1 is a sub-micro, or nano-sized drive with a full range of features to meet the needs of nearly any user. The nc1 is designed to be

More information

Understanding VFD. Variable Frequency Drive. nfi. nfi

Understanding VFD. Variable Frequency Drive. nfi. nfi Understanding VFD Variable Frequency Drive Practical Demonstration of VFD Delta- M Series 1.5 KW I/P: 230V 1/3 Phase O/P: 230 3 Phase VFD Status Screen Motor OFF Command Freq. Parameters Direction Amperes

More information

VAT 20 Adjustable Frequency Drive

VAT 20 Adjustable Frequency Drive VAT 0 Adjustable Frequency Drive VAT 0 Adjustable Frequency Drive The VAT 0 is a small, flexible, low cost, well performing AC drive designed for use in small machines such as fans and conveyors. The drive

More information

Understanding VFD Allen Bradley Power Flex 4M Variable Frequency Drive. nfi

Understanding VFD Allen Bradley Power Flex 4M Variable Frequency Drive. nfi Understanding VFD Allen Bradley Power Flex 4M Variable Frequency Drive nfi Practical Demonstration of VFD Motor Speed Directly Proportional to Frequency Motor RPM= (120*F)/P Powerflex- 4M 0.4 KW= 0.5 Hp

More information

BOSTON GEAR CONTROLLERS. ACE 10 Series 1/4 through 3 HP Adjustable Frequency AC Motor Controllers MEX (55) QRO (442)

BOSTON GEAR CONTROLLERS. ACE 10 Series 1/4 through 3 HP Adjustable Frequency AC Motor Controllers MEX (55) QRO (442) BOSTON GEAR CONTROLLERS ACE 10 Series 1/4 through 3 HP Adjustable Frequency AC Motor Controllers ACE 10 Series Noted for exceptionally low motor noise, high starting torque and cool operation in a compact

More information

2. Using LCD Digital Operator

2. Using LCD Digital Operator 2. Using LCD Digital Operator Functions of LCD digital operator JNEP-31(V) LCD digital operator has 2 modes: mode and mode. When the inverter is stopped, mode or mode can be selected by pressing the. In

More information

Electronic Lineshaft With Alignment F7 Drive Software Technical Manual

Electronic Lineshaft With Alignment F7 Drive Software Technical Manual Electronic Lineshaft With Alignment F7 Drive Software Technical Manual Software Number: VSF11005X, Drive Models: CIMR-F7UXXXXXX-064, CIMR-F7UXXXXXX-065 Document Number: TM.F7SW.064, Date: 02/25/2010, Rev:

More information

RM5 User Manual Warnings.

RM5 User Manual Warnings. A RM5 User Manual Warnings. Danger Hazardous High Voltage Ground the control before servicing Remove all power and wait 10 minutes Verify that no voltage is present Failure to comply will result in death

More information

Basic Specifications. Driver Model SD12B/15B SD20B SD30B SD30C SD40C SD50C SD75C

Basic Specifications. Driver Model SD12B/15B SD20B SD30B SD30C SD40C SD50C SD75C Basic Specifications Driver Model SD12B/15B SD20B SD30B SD30C SD40C SD50C SD75C Applicable Motor Maximum Current 8.4A 11.4A 17.0A 17.0A 22.8A 28.2A 42.3A Input Power Feedback System single-phase AC180V

More information

DAAB DB409 INSTRUCTION MANUAL FOR THE VFD-EL FREQUENCY CONVERTER. For the DAAB EP104 automatic control system with software version 4.

DAAB DB409 INSTRUCTION MANUAL FOR THE VFD-EL FREQUENCY CONVERTER. For the DAAB EP104 automatic control system with software version 4. DAAB DB409 INSTRUCTION MANUAL FOR THE VFD-EL FREQUENCY CONVERTER For the DAAB EP104 automatic control system with software version 4.07 Revision: 12 FAAC Nordic AB BOX 125, SE-284 22 PERSTORP SWEDEN, +46

More information

Inverters Selection Guide

Inverters Selection Guide Inverters Selection Guide Table of contents SYSDRIVE inverters Page Inverter - Outline...................................................................... 1 3G3EV................................................................................

More information

Frequency Converter EFC 3610, EFC 5610

Frequency Converter EFC 3610, EFC 5610 Frequency Converter EFC 3610, EFC 5610 2 EFC 3610, EFC 5610 frequency converter Using valuable energy responsibly Using valuable energy responsibly Rising energy costs and increasing demands for environmentally-friendly

More information

Single Axis Position Controller

Single Axis Position Controller SERIES P9511 Single Axis Position Controller Compact Construction Simple Go-to operation Integrated Relay Output Integrated Mains Power Supply ELEKTRO-TRADING sp. Z o.o. 44-109 Gliwice, ul. Mechaników

More information

Soft starter, 66 A, V AC, Us= 24 V DC, with control unit, Frame size N. Function Soft starter for three-phase loads, with control unit

Soft starter, 66 A, V AC, Us= 24 V DC, with control unit, Frame size N. Function Soft starter for three-phase loads, with control unit DATASHEET - S811+N66N3S Delivery program Soft starter, 66 A, 200-600 V AC, Us= 24 V DC, with control unit, Frame size N Part no. S811+N66N3S Catalog No. 168978 Eaton Catalog No. S811PLUSN66N3S EL-Nummer

More information

Motion Control G7 Drive Software Technical Manual

Motion Control G7 Drive Software Technical Manual Software Number: VSG13306X, Drive Models: CIMR-G7UXXXXX-117 Document Number: TM.G7SW.117, Date: 05/16/08, Rev: 08-05 Motion Control G7 Drive Software Technical Manual Contents: 1.0 Overview... 3 2.0 Changes

More information

Frequency Converter EFC 3610, EFC 5610

Frequency Converter EFC 3610, EFC 5610 Frequency Converter EFC 3610, EFC 5610 2 EFC 3610, EFC 5610 frequency converter Using valuable energy responsibly Using valuable energy responsibly Rising energy costs and increasing demands for environmentally-friendly

More information

Rexroth IndraDrive Fc Compact, high-performance standard frequency converters

Rexroth IndraDrive Fc Compact, high-performance standard frequency converters Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Rexroth IndraDrive Fc Compact, high-performance standard frequency converters Simply a better drive 2

More information

Rexroth IndraDrive Fc Compact, high-performance standard frequency converters

Rexroth IndraDrive Fc Compact, high-performance standard frequency converters Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Rexroth IndraDrive Fc Compact, high-performance standard frequency converters Simply a better drive 2

More information

Inverters Selection Guide

Inverters Selection Guide Inverters Selection Guide Table of contents SYSDRIVE inverters Page Inverter - Outline...................................................................... 1 3G3EV................................................................................

More information

ENGINEERING PUBLICATION

ENGINEERING PUBLICATION ENGINEERING PUBLICATION MOTION CONTROL DIVISION PRODUCT: JUSP-NS600 SIGMA II INDEXER SUBJECT: USING THE DIGITAL OPERATOR WITH THE SIGMA II INDEXER CATEGORY: TECH NOTE ENGINEER: Paul Zajac DISTRIBUTION:

More information

SOFT STARTER. We are delivering Real Cost Benefits CD AUTOMATION POWERED BY INNOVATION. Soft Starter Catalog 2018 Release n.

SOFT STARTER. We are delivering Real Cost Benefits CD AUTOMATION POWERED BY INNOVATION.   Soft Starter Catalog 2018 Release n. 380 to 600V Nominal current 6 to 200A ST with Soft Start STO with Soft Start + Overload Relay Internal by pass relay SOFT STARTER CD AUTOMATION POWERED BY INNOVATION We are delivering Real Cost Benefits

More information

Atlas Drop In Decoder

Atlas Drop In Decoder TCS DCC decoders provide the ultimate in control. This decoder is in # A1 Atlas Drop In Decoder 1.3 amp continuous, 2.0 amp peak motor drive plus four 100 ma function outputs Dither creates the ultimate

More information

Low-cost labelling system

Low-cost labelling system Low-cost labelling system Star2000 Labelling-Printing handbook 060517.doc Edition: Revision 2 dated - 17 th May 2006 2 Application description In this labelling machine example two labels are required

More information

Digital Ratio Controller

Digital Ratio Controller Digital Ratio Controller RSC-406 Control Panel USER S MANUAL RATIO CONTROLLER SPEED RUN PRG ERR RATIO % CH RSC-406 Prelude Thank you for applying our RSC-406 Ratio Controller (abb.406) to you machinery

More information

BE1-81O/U Frequency Protection. Washington State University Hands-On Relay School.

BE1-81O/U Frequency Protection. Washington State University Hands-On Relay School. Frequency Protection Washington State University Hands-On Relay School www.basler.com Relay Benefits As many as four independent, adjustable frequency setpoints and time delays Each setpoint has output

More information

Variable Speed Drives OMRON/YASKAWA F7Z - series

Variable Speed Drives OMRON/YASKAWA F7Z - series Variable Speed Drives OMRO/YASKAWA F7Z - series Short manual: F7-series with Software for Speed control of compressors with integrated compound controller PED Power Electronics Deutschland GmbH Conradtystrasse

More information

02/11/2015

02/11/2015 DIN Rail Mount 17.5 mm MUS/MUSF 80 AC/DC Part number 84872141 Control relays monitoring their own power supply - MUS : Over/undervoltage control Selectable latching (memory) function - MUSF : Over/undervoltage

More information

Software Wizard Makes Configuring the 2301E Easier Configuration Wizard Now Included in 2301E Service Tool

Software Wizard Makes Configuring the 2301E Easier Configuration Wizard Now Included in 2301E Service Tool Software Wizard Makes Configuring the 2301E Easier Configuration Wizard w Included in 2301E Service Tool The 2301E Configuration Wizard makes it easier to set up and use the 2301E Load Sharing Speed Control

More information

Synchronization Check Relay ARGUS 7

Synchronization Check Relay ARGUS 7 Synchronization Check Relay ARGUS 7 Page 1 of 8 Table of Contents Secondary injection tests:... 3 Phase Angle Test:... 3 CS PHASE ANGLE:... 3 SS PHASE ANGLE:... 3 SLIP FREQUENCY TEST:... 4 CS SLIP FREQUENCY:...

More information

UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load Cell

UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load Cell 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load

More information

RYKO Italia s.r.l. V. Casale Morano Po (Al) t f ITALIA SERVICE BULLETIN - #1-002 Senco 5 Adjustment (revised)

RYKO Italia s.r.l. V. Casale Morano Po (Al) t f ITALIA SERVICE BULLETIN - #1-002 Senco 5 Adjustment (revised) Italia RYKO Italia s.r.l. V. Casale 43-15025 Morano Po (Al) t.0142 85871 f. 85872 July 11, 2000 July 19, 2001 MACHINES AFFECTED: ITALIA SERVICE BULLETIN - #1-002 Senco 5 Adjustment (revised) All machines

More information

Transmitter Interface Program

Transmitter Interface Program Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following

More information

EA63-7D. Generator Automatic Voltage Regulator Operation Manual. Self Excited Automatic Voltage Regulator

EA63-7D. Generator Automatic Voltage Regulator Operation Manual. Self Excited Automatic Voltage Regulator EA63-7D Generator Automatic Voltage Regulator Operation Manual Self Excited Automatic Voltage Regulator SP POWERWORLD LTD Willows, Waterside, Ryhall, Stamford, Lincs, PE9 4EY, UK Tel: +44 1780 756872 -

More information

Variwrap Controller Manual

Variwrap Controller Manual Variwrap Controller Manual Operation The controller has two operating modes Manual and Auto. The mode is changes by pressing the (F1) Auto/Manual button. The mode setting is displayed in the top right

More information

Frequency Converter Fv

Frequency Converter Fv 2 Bosch Rexroth AG Electric Drives and Controls Documentation Brake chopper with up to 30 kw continuous braking power Easy to operate and service (detachable fan, LCD operating panel with copy function)

More information

Model IQ4-PC User Manual Revision Date:

Model IQ4-PC User Manual Revision Date: Basic Specifications Supply Volts 230V 50/60Hz ±15% 115V 50/60Hz ±15% 24V DC (isolated) ±15% Power Consumption Max. 3VA (IQ4-PC-R0) Max. 6VA (IQ4-PC-R2-PSI24-RT) Operating Temperature -5 ~ +60 C Operating

More information

High performance circuit breakers

High performance circuit breakers Series High performance Description The high performance MCB offers a compact solution to circuit protection. The devices are DIN rail mounted. The is available with application-specific trip characteristics

More information

Transfer Switch. OTECA (Spec A) OTECB (Spec A) OTECC (Spec A) OTECD (Spec A) Amperes. English Original Instructions (Issue 5)

Transfer Switch. OTECA (Spec A) OTECB (Spec A) OTECC (Spec A) OTECD (Spec A) Amperes. English Original Instructions (Issue 5) Operator Manual Transfer Switch 40-1000 Amperes OTECA (Spec A) OTECB (Spec A) OTECC (Spec A) OTECD (Spec A) English Original Instructions 10-2015 962-0131 (Issue 5) Table of Contents 1. SAFETY PRECAUTIONS...

More information

SIMOREG DC Master. Application SIMOREG 1Q-device, braking to defined speed using reversing. 6RA70 Series

SIMOREG DC Master. Application SIMOREG 1Q-device, braking to defined speed using reversing. 6RA70 Series SIMOREG DC Master 6RA7 Series Application SIMOREG Q-device, braking to defined speed using reversing Microprocessor-ased Converters from 6kW to 9kW for Variable-Speed DC Drives Edition Edition 2 NOTE This

More information

RD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011

RD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011 RD - 122 RACK MOUNT DIMMER OWNERS MANUAL VERSION 1.3 03/09/2011 Page 2 of 14 TABLE OF CONTENTS UNIT DESCRIPTION AND FUNCTIONS 3 POWER REQUIREMENTS 3 INSTALLATION 3 PLACEMENT 3 POWER CONNECTIONS 3 OUTPUT

More information

POLARIS 4 ELECTRONIC CONTROL BOARD FOR SLIDING GATES MANUAL

POLARIS 4 ELECTRONIC CONTROL BOARD FOR SLIDING GATES MANUAL POLARIS 4 ELECTRONIC CONTROL BOARD FOR SLIDING GATES MANUAL !!! ATTENTION - NOTICE FOR THE INSTALLER!!! The bridges present on the contacts STOP, SENSITIVE EDGE, PHOTOCELLS, will not be installed anymore

More information

SHUTTLE WITH INFRA-RED DETECTION SAS2-IR

SHUTTLE WITH INFRA-RED DETECTION SAS2-IR SHUTTLE WITH INFRA-RED DETECTION SAS2-IR Shuttle Model Train Controller with Infra-Red Detection Automatically operates a train backwards and forwards along a single line. Train detection using Infra-red

More information

User Guide UD51. Second encoder small option module for Unidrive. Part Number: Issue Number: 5.

User Guide UD51. Second encoder small option module for Unidrive. Part Number: Issue Number: 5. EF User Guide UD51 Second encoder small option module for Unidrive Part Number: 0460-0084-05 Issue Number: 5 www.controltechniques.com Safety Information The option card and its associated drive are intended

More information

LE062XF DCC Decoder for Atlas N Scale Locomotives

LE062XF DCC Decoder for Atlas N Scale Locomotives Locomotive decoder LE062XF 1 The LE062XF DCC decoder is designed to fit specific Atlas N scale locomotives, including the SD50, SD-60, and SD-60M. The characteristics of this decoder are: Provides 0.5

More information

PRINCIPLES AND APPLICATIONS

PRINCIPLES AND APPLICATIONS GENERATION & NETWORK Digital Automation Measuring and Control Devices AMS7000 PROCOM The optimum operation of an electrical network depends particularly on the reliability and the availability of the protection,

More information

CDHD Servo Drive. Technical Training Manual. Manual Revision: 2.0 Firmware Version: 1.3.x Software Version: 1.3.x.x

CDHD Servo Drive. Technical Training Manual. Manual Revision: 2.0 Firmware Version: 1.3.x Software Version: 1.3.x.x CDHD Servo Drive Technical Training Manual Manual Revision: 2.0 Firmware Version: 1.3.x Software Version: 1.3.x.x CDHD Introduction Revision History Document Revision Date Remarks 1.0 June 2012 Initial

More information

1. Type identification Nameplate Nameplate, IO Nameplate, CU Configuration file label...

1. Type identification Nameplate Nameplate, IO Nameplate, CU Configuration file label... Service instructions Control MPC 1. Type identification... 2 1.1 ameplate... 2 1.2 ameplate,... 3 1.3 ameplate, CU 351... 4 1.4 Configuration file label... 5 2. Technical data... 6 2.1 Temperature... 6

More information

DLP200M 2 Relay Module for Heating and Cooling Plants

DLP200M 2 Relay Module for Heating and Cooling Plants Product Sheet TH6.24 Thermostat Type DLP200M DLP200M 2 Relay Module for Heating and Cooling Plants The DLP 200 M is a relay module for activation of loads (namely thermal actuators or circulators) in wireless

More information

MICROMASTER Encoder Module

MICROMASTER Encoder Module MICROMASTER Encoder Module Operating Instructions Issue 01/02 User Documentation Foreword Issue 01/02 1 Foreword Qualified Personnel For the purpose of this Instruction Manual and product labels, a Qualified

More information

GENMARK Engineering & Management # Street Edmonton, AB T5S 1R5 CANADA Phone (780) Fax (780)

GENMARK Engineering & Management # Street Edmonton, AB T5S 1R5 CANADA Phone (780) Fax (780) GENMARK Engineering & Management #200 10459-178 Street Edmonton, AB T5S 1R5 CANADA Phone (780) 461-9234 Fax (780) 461-9624 GENMARK Engineering & Management Contract engineering and management services

More information

DZ143. Z Scale. Mobile Decoder 1.25 Amp/2 Amp Peak 4 FX 3 Functions, 0.5 Amp. Fits Many Z, N and HO Scale Locomotives

DZ143. Z Scale. Mobile Decoder 1.25 Amp/2 Amp Peak 4 FX 3 Functions, 0.5 Amp. Fits Many Z, N and HO Scale Locomotives Digitrax Command Control Run Your Trains, Not Your Track! DZ143 Fits Many Z, N and HO Scale Locomotives Z Scale Mobile Decoder 1.25 Amp/2 Amp Peak 4 FX 3 Functions, 0.5 Amp Features: Digitrax LocoMotion

More information

Frequency Converter EFC 3610, EFC 5610

Frequency Converter EFC 3610, EFC 5610 Frequency Converter EFC 3610, EFC 5610 2 EFC 3610, EFC 5610 frequency converter Using valuable energy responsibly Using valuable energy responsibly Rising energy costs and increasing demands for environmentally-friendly

More information

Operating instructions Electronic preset counter Type series 717

Operating instructions Electronic preset counter Type series 717 Operating instructions Electronic preset counter Type series 717 1. Description 5.98.3_gb 6-digit adding/subtracting counter with two presets Very bright 8mm high LED display Counting and preset range

More information

PIPV200 QUAD System. User Manual

PIPV200 QUAD System. User Manual PIPV200 QUAD System User Manual System Features - Connects up to 4/8 Video Camera Adjustable Brightness, Contrast, Saturation, Hue and Sharpness - High Resolution 720X480 60Hz for NTSC 720X576 50Hz for

More information

Factory configured macros for the user logic

Factory configured macros for the user logic Factory configured macros for the user logic Document ID: VERSION 1.0 Budapest, November 2011. User s manual version information Version Date Modification Compiled by Version 1.0 11.11.2011. First edition

More information

Automatic Transfer Switch Control PLC Operator s Manual

Automatic Transfer Switch Control PLC Operator s Manual MTS Power Products MIAMI FL 33142 ATS-22AG Automatic Transfer Switch Control PLC Operator s Manual Dedicated Single Phase Transfer Switch ATS-22AG Automatic Transfer Switch INTRODUCTION 1.1 Preliminary

More information

Rotary Knife Controller

Rotary Knife Controller PCM-22 Rotary Knife Controller Information furnished by EMERSON Motion Control is believed to be accurate and reliable. However, no responsibility is assumed by EMERSON Motion Control for its use. EMERSON

More information

KNX Dimmer RGBW - User Manual

KNX Dimmer RGBW - User Manual KNX Dimmer RGBW - User Manual Item No.: LC-013-004 1. Product Description With the KNX Dimmer RGBW it is possible to control of RGBW, WW-CW LED or 4 independent channels with integrated KNX BCU. Simple

More information

MC700 / MC720 Motion Control Firmware for Rotating Cutters and Printing Rolls. Cutting Pulse Sensor Optional: Print Mark Sensor

MC700 / MC720 Motion Control Firmware for Rotating Cutters and Printing Rolls. Cutting Pulse Sensor Optional: Print Mark Sensor CT 703.03 Firmware MC700 / MC720 Motion Control Firmware for Rotating Cutters and Printing Rolls Cutting Pulse Sensor Optional: Print Mark Sensor Slave Encoder Master Encoder Cutting Roll Drive 0-10V MC700

More information

Decoder version 3.5. Plug and play decoder for N-Scale Atlas Classic Series GP7, GP9, GP30, GP35

Decoder version 3.5. Plug and play decoder for N-Scale Atlas Classic Series GP7, GP9, GP30, GP35 NA Function Decoder $9.95 Decoder version 3.5 Plug and play decoder for N-Scale Atlas Classic Series GP7, GP9, GP30, GP35 This is an EPF (extended packet format) decoder supporting : Silent Running TM

More information

STX Stairs lighting controller.

STX Stairs lighting controller. Stairs lighting controller STX-1795 The STX-1795 controller serves for a dynamic control of the lighting of stairs. The lighting is switched on for consecutive steps, upwards or downwards, depending on

More information

Noise Detector ND-1 Operating Manual

Noise Detector ND-1 Operating Manual Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation

More information

SPECIFICATION NO NOTE

SPECIFICATION NO NOTE NOTE The Model 207-1 is a special version of the standard M-207 Power Supply. It has been altered for a special applications requiring low current operation at high arc voltages in ambient and pressurized

More information

Panasonic Broadcast. AW-HE100 Menu Information

Panasonic Broadcast. AW-HE100 Menu Information Panasonic Broadcast AW-HE100 Menu Information Basic menu operations Menus are displayed on the monitor when the unit s settings are to be selected. The monitor is connected to the video signal output connector

More information

Basic, cost-effective motor control in one unit: MOVITRAC 07.

Basic, cost-effective motor control in one unit: MOVITRAC 07. Gearmotors \ Industrial Gear Units \ Drive Electronics \ Drive Automation \ Services Basic, cost-effective motor control in one unit: MOVITRAC 07. Frequency inverter 2 Basic, cost-effective motor control

More information

21 Channel Light Show PWM LED Controller with Remote Control

21 Channel Light Show PWM LED Controller with Remote Control 21 Channel Light Show PWM LED Controller with Remote Control Application: Managing dynamic illuminated advertising signs, spectacular light walls, podiums, etc. Managing groups LED and LED strips - from

More information

Form C: Type Test Verification Report

Form C: Type Test Verification Report Form C: Type Test Verification Report Type Approval and Manufacturer declaration of compliance with the requirements of G98. This form should be used when making a Type Test submission to the Energy Networks

More information

Series CT7N Bimetallic Overload Relays

Series CT7N Bimetallic Overload Relays Series CT7N imetallic Overload Relays Choose CT7N overloads in DC applications and when monitoring Variable Frequency Drives Sprecher + Schuh has always paid particular attention to the subject of motor

More information

Form C: Type Test Verification Report

Form C: Type Test Verification Report Form C: Type Test Verification Report Type Approval and Manufacturer declaration of compliance with the requirements of G98. This form should be used when making a Type Test submission to the Energy Networks

More information

Computer Controlled Advanced Industrial Servosystems Trainer (for AC motors) SERIN/CA

Computer Controlled Advanced Industrial Servosystems Trainer (for AC motors) SERIN/CA Technical Teaching Equipment Computer Controlled Advanced Industrial Servosystems Trainer (for AC motors) SERIN/CA Always included in the supply: Teaching Technique used RTC. EDIBON Real Time Control System

More information

PLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator

PLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator 3.635.5275.254 IM-P486-18 CH Issue 3 PLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator Installation, Start-up and Operation Manual 1. Safety information 2. General product information

More information

17.2 Setting the slow speed Important advice on ABC Push-pull (shuttle) train control Push-pull operation without

17.2 Setting the slow speed Important advice on ABC Push-pull (shuttle) train control Push-pull operation without 2 Contents 1 Preface...4 2 Important advice, please read first!...5 3 The GOLD series at a glance...6 3.1 Features of the GOLD decoder...6 4 Setting (programming) the decoder...9 4.1 Variable decoder features

More information

Product Catalog Frequency Converters

Product Catalog Frequency Converters Product Catalog Frequency Converters Contents Frequency converters product catalog 3 Contents Overview 4 EFC 3600 6 Frequency Converter Fv 12 Frequency Converter Fe 18 Accessories 24 Discover the unlimited

More information

Bulletin 190 IEC Modular Starter System

Bulletin 190 IEC Modular Starter System Bulletin 90 Table of Contents Selection Guide Description Page Bulletin 90....................................... Accessories....................................... 7 Specifications.....................................

More information

REMOTE I/O R30 SERIES. PC CONFIGURATOR SOFTWARE Model: R30CFG Ver Users Manual

REMOTE I/O R30 SERIES. PC CONFIGURATOR SOFTWARE Model: R30CFG Ver Users Manual REMOTE I/O R30 SERIES PC CONFIGURATOR SOFTWARE Model: R30CFG Ver. 1.13 Users Manual 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Tel: +81-6-6659-8201 Fax: +81-6-6659-8510 http://www.m-system.co.jp/

More information

Gamma instabus. Technical product information

Gamma instabus. Technical product information Gamma instabus Technical product information Universal dimmer N 554D31, 4 x 300 VA / 1x 1000 VA, AC 230 V Universal dimmer N 554D31 Control of dimmable lamps, including LED without minimum load Output

More information

Product Discontinuation Notices. Discontinuation Notice of built-in Power Supply Photoelectric sensors E3B2 series

Product Discontinuation Notices. Discontinuation Notice of built-in Power Supply Photoelectric sensors E3B2 series PRODUCT NEWS Product Discontinuation Notices March 1, 2011 Photoelectric Sensors No. 2011E011 Discontinuation Notice of built-in Power Supply Photoelectric sensors E3B2 series Product Discontinuation E3B2-D2

More information

TUSKIN Equipment Corporation

TUSKIN Equipment Corporation TUSKIN Equipment Corporation TC-101 Liquid Color Metering System Operation & Maintenance Manual Warning: Read instructions carefully before attempting to install, operate or service the Tuskin Metering

More information

Luminaire installation box Surface-mounted box Ceiling installation box

Luminaire installation box Surface-mounted box Ceiling installation box -Smart PTM Ambient light sensor and motion detector for constant lighting control uminaire installation box Surface-mounted box Ceiling installation box Overview: -SMART PTM i is an ambient light sensor,

More information

12months. on-site warranty. DZE ELECTRONIC PRESSURE SWITCH for detection of overload per EN 81 2 featuring two adjustable switching points

12months. on-site warranty. DZE ELECTRONIC PRESSURE SWITCH for detection of overload per EN 81 2 featuring two adjustable switching points BUCHER PRODUCTS AVAILABLE FROM HYDRATEC DZE ELECTRONIC PRESSURE SWITCH for detection of overload per EN 81 2 featuring two adjustable switching points 12months on-site warranty All our work comes with

More information

RGB-3400-X RGB SEQUENCER / 3-CHANNEL UNIVERSAL LED DIMMER

RGB-3400-X RGB SEQUENCER / 3-CHANNEL UNIVERSAL LED DIMMER TOUCHLESS SWITCHES. WHEN THE DESIN NEEDS TO E ASOLUTELY PEFECT -300-X SEQUENCE / 3-CHANNEL UNIVESAL LED DIMME Description -300-X is a dual function unit and can operate in two distinct modes. In Mode the

More information

Close supervision. Simplicity of use. Productivity gains. Control relay. C-Lynx. Instinctive control

Close supervision. Simplicity of use. Productivity gains. Control relay. C-Lynx. Instinctive control Close supervision Simplicity of use Productivity gains Control relay C-Lynx Instinctive control C-Lynx Control relay 1 Close-up protection for total availability of equipment! By installing a control relay,

More information

Manual. MOVIDRIVE MDX61B DRS11B Synchronous Operation Card. Edition 10/ / EN

Manual. MOVIDRIVE MDX61B DRS11B Synchronous Operation Card. Edition 10/ / EN Gearmotors \ Industrial Gear Units \ Drive Electronics \ Drive Automation \ s MOVIDRIVE MDXB DRSB Synchronous Operation Card Edition 0/2007 78 / EN Manual SEW-EURODRIVE Driving the world General Information...

More information

RG NDT INTERNATIONAL INC. Drill Pipe and Tubing Inspection System

RG NDT INTERNATIONAL INC. Drill Pipe and Tubing Inspection System RG NDT INTERNATIONAL INC Computerized Drill Pipe Manual 165 Oates Road Houston, Texas 77013 Phone: 713-673-5928 Fax: 713-673-5957 ELECTRONIC DRILL PIPE DESK MOTORIZED BUGGY DRIVE HEAD 2 Table of Contents

More information

SITOP power supply. Technical data, April SITOP Power Supply. Answers for industry.

SITOP power supply. Technical data, April SITOP Power Supply. Answers for industry. SITOP power supply Technical data, April 2010 SITOP Power Supply Answers for industry. SITOP reliable power supply Efficient operation of a machine or plant requires a reliable, constant power supply.

More information

This document is a reference document that shows the menus in the 5500sc, 9610sc and 9611sc analyzers. There are 3 top-level menus:

This document is a reference document that shows the menus in the 5500sc, 9610sc and 9611sc analyzers. There are 3 top-level menus: Controller menus 5500sc, 9610sc and 9611sc analyzers DOC273.53.80566 Introduction This document is a reference document that shows the menus in the 5500sc, 9610sc and 9611sc analyzers. There are 3 top-level

More information

MOVIDRIVE Drive Inverters

MOVIDRIVE Drive Inverters T MOVIDRIVE Drive Inverters Manual Synchronous Operation Type DRSA Edition 04/ 0/22/7 C U L U L 0 30 / 0 Important Information This supplementary information does not replace the detailed operating instructions!

More information

Click Here To Start Demo

Click Here To Start Demo Click Here To Start Demo AirLogix Demo Title Screen AirLogix Interactive Demonstrator Version 3.0 Copyright 2005 by Case Engineering inc This is intended as a working active demonstration only. Every attempt

More information

From the above diagram, the relationship between X1, X2, X a and C a is given by the following equations:

From the above diagram, the relationship between X1, X2, X a and C a is given by the following equations: Cross-Coupled Drive of Dual-Motor Gantry System Usually, the control of the multi-motor gantry system is done by either the classic master-slave or the full coordination method on PMAC. In this application

More information

All real signals have scale factor 10. Integer, Index and Logic has always scale factor 1.

All real signals have scale factor 10. Integer, Index and Logic has always scale factor 1. STRA communication The types of the signals (types in the list below): 1 = Coil Status Register ( function = 1, 5 and 15) - 0x 2 = Discrete Input ( function = 2) - 1x 3 = Holding Register ( function =

More information

INTRODUCTION INTRODUCTION

INTRODUCTION INTRODUCTION INTRODUCTION INTRODUCTION This manual describes the 5740X-400/401 Strider Speed Control, and is intended to be a guide in the installation and operation of the control. This first section, the INTRODUCTION,

More information

LED DRIVERS. LQC4D-V1 4 channels. User Manual FEATURES

LED DRIVERS. LQC4D-V1 4 channels. User Manual FEATURES pag. 1/13 FEATURES Outputs: 4 x channels BUS+SEQUENCER+FADER+DIMMER+DRIVER Input: DC 12/24/48 Vdc BUS Command: DALI LOCAL Command: 4x N.O. push button (with or without memory), 0-10V, 1-10V Controls: dimmer,

More information

Selection guide siemens.com/sirius-modular-system

Selection guide siemens.com/sirius-modular-system SIRIUS modular system Selection guide siemens.com/sirius-modular-system Everything for the control cabinet: SIRIUS modular system Efficiently combined Advantages at a glance: Load feeders: easy to implement

More information

User interface. Abbreviations / Meanings

User interface. Abbreviations / Meanings RG66012649 User interface Contents Page Abbreviations / Meanings Abbreviations / meanings... 2 Button Identification... 3 On-screen Indicators... 4 Quick Start... 5 Setting the time and day... 5 Changing

More information

CET DOUBLE COUNTER WITH TWO THRESHOLDS LBM62CD. Type: TECHNICAL FEATURES

CET DOUBLE COUNTER WITH TWO THRESHOLDS LBM62CD. Type: TECHNICAL FEATURES CET DOUBLE COUNTER WITH TWO THRESHOLDS Type: LBM62CD 6 DIGITS DOUBLE DIGITAL COUNTER WITH TWO SEPARATE COUNT IMPUTS LBM62CD counter is a double counter with two separate counters. Each counter s input

More information

SPECIFICATION NO Model 207 Automatic GTAW Welding System

SPECIFICATION NO Model 207 Automatic GTAW Welding System 1.0 Introduction The Model 207 is a completely self-contained Gas Tungsten Arc Welding (GTAW) System requiring only input power, inert gas and AMI Welding Head (or manual torch) for operation. Its small

More information

ORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual

ORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual ORM0022 EHPC210 Universal Controller Operation Manual Revision 1 EHPC210 Universal Controller Operation Manual Associated Documentation... 4 Electrical Interface... 4 Power Supply... 4 Solenoid Outputs...

More information

ABB CM-UFD.M31 monitoring datasheet

ABB CM-UFD.M31 monitoring datasheet ABB CM-UFD.M31 monitoring datasheet http://www.manuallib.com/abb/cm-ufd-m31-monitoring-datasheet.html The CM-UFD.M31 is a multifunctional grid feeding monitoring relay. It provides different monitoring

More information