AMIGO. User Operation Manual. 8-VSB Modulator. >> Fourth Edition

Transcription

1 8-VSB Modulator AMIGO User Operation Manual >> Fourth Edition LUMANTEK Co., Ltd Head Office : # 1208, Woolim Lion s Valley II, Gasan-Dong Geuncheon-Gu SEOUL, KOREA ( ) TEL: FAX: inquire@lumantek.com

2 Trademarks and copyright COPYRIGHT 2009, LUMANTEK Unit 1208, Woolim Lion s Valley II, 680 Gasan-Dong, Gumcheon Gu, Seoul Korea ( ), Tel: , Fax: All rights reserved. This document contains information that is proprietary to LUMANTEK. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of LUMANTEK. Nationally and internationally recognized trademarks and trade names are the property of their respective holders and are hereby acknowledged. Portions of this software are LUMANTEK Ltd. All intellectual property rights in such portions of the Software and documentation are owned by LUMANTEK and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. LUMANTEK and its suppliers retain all rights not expressly granted. Disclaimer The information in this document is furnished for informational purposes only, is subject to change without prior notice, and should not be construed as a commitment by LUMANTEK. The information in this document is believed to be accurate and reliable; however LUMANTEK assumes no responsibility or liability for any errors or inaccuracies that may appear in this document, nor for any infringements of patents or other rights of third parties resulting from its use. No license is granted under any patents or patent rights of LUMANTEK. This document was written by the Technical Support Department of LUMANTEK, Korea. We are committed to maintaining a high level of quality in all our documentation. Towards this effort, we welcome your comments and suggestions regarding the content and structure of this document. Please fax or mail your comments and suggestions to the attention of: LUMANTEK Attn: Product Support Department Unit 1208, Woolim Lion s Valley II, 680 Gasan-Dong, Gumcheon Gu, Seoul Korea ( ), , Fax: Environmental Issues Thank you for buying a product which contributes to a reduction in pollution and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either no or few consumable parts (chemicals, toner, gas, paper). Our products are low energy consuming products. Waste handling: There is need to send material back to LUMANTEK. Please contact your local dealer for information on recycling the product by sending the main parts of the product for disassembly at local electronic waste stations. Production of products: Our factories employ the most efficient environmental methods for reducing waste and pollution by ensuring that the products are recyclable.

3 Contents 1. AMIGO System Overview 5 2. Key Feature 5 3. Product Description Product Appearance Front Panel Rear Panel Side Panel 8 4. Product Contents 8 5. Precautions 9 6. AMIGO Operation Hyper Terminal (RS 232C Port) 12

4 1. AMIGO System Overview AMIGO is 8-VSB Modulator which has been applied to ATSC standard. Its Input Interface supports SMPTE-310M (Society of Motion Picture and Television Engineers) and DVB-ASI Input. AMIGO receives MPEG2 TS (Transport Stream) through DVB ASI Input or SMPTE- 310M Input Interface. And it modulates with 8-VSB and makes RF Signal by built-in RF Up Converter. 2. Key Feature Basic Structure Input Interface IF Output RF Output Modulation Method ATSC (8-VSB) Modulator DVB-ASI over BNC-75 Ohm Comply with EN byte / 204 byte 1 to 100 Mbps SMPTE-310M over BNC-75 Ohm Mbps Input REFERENCE 10Mhz 10Mhz Input (except 75 Ω) IF Modulator Output 44MHz (+, Khz) Digital Tuning resolution : 1Hz Channel Bandwidth 6MHz Connector 50 Ω BNC VHF/UHF Output Frequency : 50 ~ 860 Mhz 1Khz Step Level : -15.0dBm ~ 7.0 dbm Attenuation : 0.5dB step Phase noise(uhf) : Better than < 10Khz, Better than < 20Khz EVM(before equalizer) : <3% RMS(at RF) MER(measured at RF) : >35dB RF Spurious Tones : Better than -60 dbc below output signal RF Harmonics : Better than -55 db below output signal IF Input : 50 Ω BNC connector or 75 Ω F-type connector RF Output connector : BNC, 50 Ω or 75 Ω -20dB TP output Standard ATSC A.53 Modulation Scheme 8-VSB Symbol rate Symbol rate : MSps AMIGO 8-VSB Modulator >> 4

5 Key Feature Dimension & Power Monitoring Return Loss -15dB Linear pre-distortion Non-linear pre-distortion Null Packet Insertion Null Packet Extract PCR Re-stamping TS Rate Monitoring (option) PID Filtering (option) PID Remapping (option) PID Monitoring (option) RS232 control port to remote management User friendly LCD UI (with 4 line LCD) Dimension 1 RU ( 19 inches Rack Mount) 483 X 44 X 380 m Weight : 3.15 kg Sash : Aluminum Power Voltage : V Power Consumption : 60W Max Front 4 line - 16 character LCD display 4 cursor keys + 2 function keys Remote Control RS pin DIN AMIGO 8-VSB Modulator >> 5

6 3. Product Description 1-1 Product Appearance 1-2 Front Panel Bellowing picture shows the front panel of 8-VSB MODULATOR. uvw x y z { } ~ t j POWER LED k MPEG LED l ALARM LED m LCD n UP BUTTON o LEFT BUTTON p DOWN BUTTON q RIGHT BUTTON r SET BUTTON s ESC BUTTON i RF TP(-20dB) : Turn on when power supply : Blink when Modulation is working : Turn on when system is error : User input window : Move up : Move left : Move down : Move right : Confirm Setting : Exit from Menu : RF Output Port 1-3 Rear Panel Bellowing picture shows the rear panel of 8-VSB MODULATOR. AMIGO 8-VSB Modulator >> 6

7 j RF OUTPUT : RF Output Port k IF INPUT : IF Input Port (50 Ω, 75 Ω) l IF OUTPUT : IF Output Port (50 Ω, 75 Ω) m RS-232 : RS-232 Port for system management n REFERENCE 10Mhz : REFERENCE 10Mhz Port (except 75 Ω) o ASI/SMPTE-310M IN : ASI / SMPTE-310M IN Port, Select on Menu p POWER INPUT : Power Input and Switch q POWER SW : Power(on/off) 1-4 Side Panel 4. Product Contents Radiant heat ventilating opening AMIGO RS 232 CABLE 50Ω Cable (BNC) : IF LOOP <- 75Ω Cable (F-type): IF Loop AMIGO 8-VSB Modulator >> 7

8 5. Precautions Please read all safety and operating instructions before using this product. For best results, be aware of all warnings on the product and follow these operating instructions. Retain these safety and operating instructions for future reference. 1. Power Source Connect this product only to the power source described in the operating instructions or as marked on the product itself. 2 Power Cable Protection Route all power cables safely. Ensure the power cables can neither be walked upon nor pinched by items placed near or against the cables. Pay particular attention to locations near AC receptacles, AC outlet strips and points of entry to the product. 3. Electrical Shocks Take care not to drop objects or spill liquids into the product through enclosure openings. Metal objects, such as hairpins or needles, inserted into the product may contact voltages resulting in serious electrical shocks. Never permit children to insert any objects into this product. 4. Ventilation Locate the product so as not to interfere with its ventilation. Do not place books or other equipment on the product that may impede the free movement of air. Allow a minimum of 4 inches (10 cm) between the rear of the product and the wall or operating desk shelf. 5. Abnormal Odors The presence of an unusual odor or smoke is often a sign of trouble. Immediately turn the power OFF and remove the power cable. Contact a dealer or the nearest Service Center for advice. 6. Servicing Remove the product s enclosure only to do accessory installations described by this manual or accessory manuals. Follow provided instructions carefully to avoid electrical shocks. If unfamiliar with this type of work, seek assistance from an experienced individual, or have a professional technician do the task. 7. Damage Requiring Service Enlist the services of qualified personnel in the following cases: a) The power supply or plug is damaged. b) Objects have fallen or liquid has spilled into the product. c) The product has been exposed to rain. d) The product is operating abnormally or performance has degraded seriously. e) The product has been dropped or the enclosure damaged. AMIGO 8-VSB Modulator >> 8

9 6. AMIGO Operation Basic Button Function LCD Display Window Set Menu and Function Basic Information is shown Move Curser and change value Move Setting Value (number) Curser to left Move Setting Value (number) Curser to right Increase Setting Value, Move Curser to Up Decrease Setting Value, Move Curser to Down Set Value Exit Menu 1. Power On Bellowing LCD Display may appear when power is supplied. - LumanTek RF : 579 Mhz, 0 dbm Ts: 0.00Mbps 2. Starting Menu Current Setting Center Rf & Display real-time rate of the TS If Rate is 0 then LCD Display show TS: No Input!!, and show Alarm signal. * 1. Rf Ch/Freq. 2. RF Power 3. Input Port 4. Spec Inv. After initialization, press [SET] Button. Menu will be shown. Main Menu are RF Ch/Freq, RF Power, Input Port, Spec Inv, Ref 10Mhz, Linear, and Nonlin. Select Menu by Up / Down Buttons and Press SET Buttons. 1. RF Freq : RF output signal setting 2. RF Power: RF output level setting 3. Input Port : Input port setting 4. Input Format : Input format setting 5. Ref 10Mhz : 10Mhz Signal setting ( except # 75Ω) 6. Linear : Set up a linear displacement AMIGO 8-VSB Modulator >> 9

10 3. RF Ch/Freq User Manual Press [SET] Button from starting menu. On Set By Menu, select Cable Ch, Terre Ch, Frequency and change Frequency by Up / Down Buttons. You can change Number by Left / Right Buttons. 1. RF Ch/Freq -> Set By : Freqeuncy Freq : 579.0Mhz < Signal Range : 50 ~ 860 MHz > 4. RF Power Choose 2.RF Power from starting menu, then press [SET] Buttons Change RF Output Level by Up / Down Buttons. You can change Number by Left / Right Buttons. 2. RF Power 0 dbm (+7 ~ -15 dbm/0.5) < Output Range : +7~ -15 dbm > 5. Input Port Choose 3.Input Port from starting menu, then press [SET] Buttons. Press Setting Buttons( ) to change input port. Input port is supported by ASI - 188, ASI - 204, SMPTE Input Port ASI In (ASI/SMPTE) < Input Port : ASI 188, ASI 204, SMPTE - 188> 6. Spec Inv. Choose 4.Input Formant from starting menu, then press [SET] Buttons. Press Setting Buttons ( ) to change input port. You can change Number by Left / Right Buttons. 4. Spec Inv. Invert. (Inv/Nor) < Spec Inv. : Inv / Nor > AMIGO 8-VSB Modulator >> 10

11 7. Ref 10Mhz. (except # 75 Ω) Choose number 5 from starting menu, then press [SET] Buttons. Press Setting Buttons( ) to change Ref 10Mhz setting. 10MHZ reference setting supportes Int, and Ext. However, the 75Ω Type is non- fixiable. 5. Ref 10Mhz. Internal [Int/Ext] < Rf 10Mhz : 10Mhz: Int / Ext > 8. Linear Choose number 6' from starting menu, then press [SET] Buttons. Press Setting Buttons ( ) to change Linear displacement compensation. Linear displacement compensation supports Off, Defalut, and User. 6. Linear Default (Off / *Default/User) < Linear: Off / *Default / User > 1. Off : A linear displacement compensation is turn off. 2. Default : Factory applied to perform linear displacement compensation. (Built-in upconverter Compensation 3. User : Value entered by the user to perform a linear displacement compensation. The initial value is Default. 9. Non - lin 2 Non-linearity inside AMIGO. Choose number 7' from starting menu, then press [SET] Buttons. Press Setting Buttons ( ) to change Linear displacement compensation. Nonlinear compensation prepositive is supported by A, B, Off. 7. Non-lin Off [A/B/off] < Non-lin: A / B / Off > A : Perform Linear compensation prepositive in saved A area. B : Perform Linear compensation prepositive in saved B area. Off : Does not work Linear compensation prepositive AMIGO 8-VSB Modulator >> 11

12 7. Hyper Terminal (RS 232C Port) Check computer s COM for using RC-232C Port Control Panel System Device Manager Ports (COM & LPT) After check Ports (COM & LPT), run RS-232C Ports Access program (Hyper Terminal, Secure CRT...). 1. Start Program Accessories Communications Hyper Terminal Input Amigo in Name, then click OK. AMIGO 8-VSB Modulator >> 12

13 2. When you click the OK button in the Serial Port Settings window appears below. Section Setting Value Baud Rate 19,200 Data Format 8 bit Stop Bit 1 Parity No Flow Control None <Port Settings> 3.Setting 1) Set/Change Frequency : (Unit : KHz) Instructions : > To change the value Example : > RF [enter] Set KHz > RF? [Enter] : Confirm changed value Example : > CC 4 [enter] Set ch 4 > CC? [Enter] : Confirm changed value Cable ch: 4 Example : > CT 5 [enter] Set ch 5 > CT? [Enter] : Confirm changed value Terrestrial ch: 5 AMIGO 8-VSB Modulator >> 13

14 2) Set / Change Output Power Level (Unit : dbuv) 3) Setting Instructions : > To change the value Example : > PW 20 [enter] Set 20 x 0.1 dbm > PW?[Enter] : Confirm changed value Instruction : Input port (ASI/SMPTE) Byte Example : >IN ASI188 [enter] Set Input port is ASI and Format is 188 Byte > IN ASI204 [enter] Set Input port is ASI and Format is 204 Byte > IN SMPTE [enter] Set Input port is SMPTE and Format is 188 Byte > IN? [Enter] ASI204/ASI188/SMPTE 4) Spectrum Inversion Instruction : SP NORMAL/INVERT [enter] Example : > SP NORMAL [enter] Set spectrum Normal set > SP INVERT [enter] Set spectrum Invert set > SP?[Enter] 5) Ref 10Mhz (75 Ω Internal is non -fixiable) Instruction : REF INTERNAL/EXTERNAL [enter] Example : > REF INTERNAL [enter] set reference Internal 10Mhz set > REF EXTERNAL [enter] set reference External10Mhz set > REF? AMIGO 8-VSB Modulator >> 14

15 6) Linear 7) Non-lin. Instruction : Using the utility to apply PD.exe Using matlab simulation results if the following, PD.exe can get by using the improved results. <Amplitude> : Before <Group Delaye> : Before Using the measured value, enter PD.exe as follows For the Port Click Select and Send, to transfer the AMIGO If you choose Fine-Tune, it will apply the previous values. If you did not choose Fine-Tune, it will previous applies regardless. AMIGO 8-VSB Modulator >> 15

16 AMIGO 8-VSB Modulator >> 16

17 <Amplitude> : After <Group Delaye> : After AMIGO 8-VSB Modulator >> 17

18 If you are Non-Linear type, select the port. Click A Block Send or B Block Send to transfer to the AMIGO. AMIGO 8-VSB Modulator >> 18

19 IMPORTANT NOTICE LUMANTEK Incorporated and its subsidiaries (LMT) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to LMT s terms and conditions of sale supplied at the time of order acknowledgment. LMT warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with LMT s standard warranty. Testing and other quality control techniques are used to the extent LMT deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. LMT assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using LMT components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. LMT does not warrant or represent that any license, either express or implied, is granted under any LMT patent right, copyright, mask work right, or other LMT intellectual property right relating to any combination, machine, or process in which LMT products or services are used. Information published by LMT regarding third party products or services does not constitute a license from LMT to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from LMT under the patents or other intellectual property of LMT. Reproduction of information in LMT data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. LMT is not responsible or liable for such altered documentation. Resale of LMT products or services with statements different from or beyond the parameters stated by LMT for that product or service voids all express and any implied warranties for the associated LMT product or service and is an unfair and deceptive business practice. LMT is not responsible or liable for any such statements. Mailing Address: LUMANTEK Unit 1208, Woolim Lion s Valley II, 680 Gasan-Dong, Gumcheon Gu, Seoul Korea Copyright 2006, LUMANTEK Incorporated

20 8-VSB Modulator AMIGO User Operation Manual LUMANTEK Co., Ltd Head Office : # 1208, Woolim Lion s Valley II, Gasan-Dong, Geuncheon-Gu, SEOUL, KOREA ( ) TEL : FAX: inquire@lumantek.com