REQUIRED TOOLS. Wire cutters Razor blade Soldering iron Pliers 11/16 Wrench for Tube 18mm Wrench for Ring

Transcription

1 S9122 PWS BNC MALE CABLE MOUNT COMPRESSION CONNECTOR S9022 PWS N TYPE MALE CABLE MOUNT COMPRESSION CONNECTOR S9322 PWS TNC MALE CABLE MOUNT COMPRESSION CONNECTOR The PWS S9122 is a BNC male cable mount compression connector. The PWS S9022 is an N type male cable mount compression connector. The PWS S9922 is a TNC male cable mount compression connector. These connectors are intended for use with PWS S9046 low loss coaxial cable only. INSTALLATION INSTRUCTIONS REQUIRED TOOLS Wire cutters Razor blade Soldering iron Pliers 11/16 Wrench for Tube 18mm Wrench for Ring 1. Remove all the parts from the packaging. Be sure you have one connector, one center pin, one rubber o-ring, one silver washer, one threaded nut. 2. Place the threaded, silver nut on the cable with the threads facing out towards the end of the cable followed by the silver washer and the rubber o-ring. Audio & RF Consultants Sales Rentals Installs 9401 American Eagle Way, Suite 100 Orlando FL Phone: Fax:

2 3. Using a razor blade carefully score the covering of the cable approximately one inch from the end of the cable. Next, filet at an angle into the cable, perpendicular to the one you just cut, until the end. You should be able to see the silver wiring inside. 4. Peel away the black covering of the cable and dispose of it. 5. Place the smaller silver ring (small edge facing outwards) onto the cable so that the bottom of it sits on the black cable. 6. Using wire cutters, cut the silver cable you exposed so that there is approximately ¼ left sticking off the end. 2

3 7. Peel back the silver threads so that only the inner rod is sticking out. 8. Carefully use the razor blade to cut the outer portion down to the copper piece inside. Remove this outer portion and dispose of it. 9. Place the gold center pin on the copper piece of cable sticking out. 10. Fold the silver threads back down to cover what s left of the base of the cable. 3

4 11. Place the BNC connector on the end of the cable. 12. To tighten, rotate the threaded nut into the body of the connector. Do not rotate the body of the connector in relation to the cable. IMPORTANT: These connectors are only for use with low-loss 50 ohm cable, such as RG-8X or equivalent. PWS S ft or 50 ft or 100 ft cables are recommended. NOTE: For additional assistance, please call the PWS technical department. SPECIFICATIONS RF Connector BNC type, female TNC type, female N type, female Dimensions 0.75 diameter 1.75 length Construction Material Aluminum Net Weight (without cable) 0.0 lbs, 1.8 oz WARRANTY AND SERVICE INFORMATION Professional Wireless Systems (PWS) manufactured products are warranted against defects in material and workmanship for a period of one year from date of original purchase, inclusive of parts and labor. This warranty excludes units that have been modified, repaired by unauthorized personnel, or damaged by abuse, improper operation, natural elements or static electricity. PWS reserves the right to make changes and/or improvements to its products, without incurring any obligation to incorporate such changes or improvements in products previously sold or shipped. PWS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER, PWS ASSUMES NO LIABILITY WHATSOEVER FOR REAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS, INCONVENIENCE OR ANY OTHER LOSSES DIRECTLY OR 4

5 INDIRECTLY ARISING FROM THE USE OF OR THE INABILITY TO USE ANY OF ITS PRODUCTS EITHER SEPARATELY OR IN COMBINATION WITH OTHER EQUIPMENT OR MATERIALS. PWS sole liability under this limited warranty shall be, at our discretion, the repair or replacement of defective products or components. To invoke this warranty, a claim must be received by PWS within the warranty period stated above and verified by PWS. Claims may be made by phone ( ) or fax ( ). Upon authorization, product shall be sent to PWS freight prepaid in the original or equivalent packaging. Products returned with excluded condition(s), out of warranty, or without authorization will be subject to parts and labor charges at prevailing rates. After a warranted product is repaired or replaced, PWS will return it freight prepaid. 5