ANI-PiP. 4x1 HDMI Seamless Quad PiP Scaler INSTRUCTION MANUAL. A-NeuVideo.com Frisco, Texas (469) AUDIO / VIDEO MANUFACTURER

Transcription

1 ANI-PiP INSTRUCTION MANUAL 4x1 HDMI Seamless Quad PiP Scaler A-NeuVideo.com Frisco, Texas (469) AUDIO / VIDEO MANUFACTURER

2 SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. 5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. 6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. 7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. 8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. 9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. 10. Turn power off and disconnect unit from AC current before making connections. 11. Never hold a power switch in the ON position. 12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. 13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically blown free of foreign dust and matter. 14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. 15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. 16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. 17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. 18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 19. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

3 CONTENTS INTRODUCTION & CONTENTS...1 FEATURES... 2 SPECIFICATIONS... 2 OPERATION CONTROLS & FUNCTIONS... 3 FRONT PANEL CONNECTION...3 REAR PANEL CONNECTION...3 REMOTE CONTROL...4 IR CODES...5 TIMING SUPPORTED... 6 RS-232 PROTOCOLS... 7 OSD MENU...12 WEB GUI INTERFACE...16 CONNECTION & INSTALLATION...21 Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. INTRODUCTION The ANI-PIP 4x1 HDMI Seamless Quad PiP Scaler is a high performance, high speed zooming/shrinking system that can be easily configured and controlled for Quad or Picture-in-Picture video processing. This unit allows (4) different input sources to be freely selected and arranged on (1) single display while supporting resolutions up to WUXGA@60Hz, 1080p and audio up to (8) Ch 192KHz for both the input and output. Screen setting hot keys with IR and RS-232 allows instant control and switching on the output display. This product has a 3 year warranty. SAFETY PRECAUTIONS TABLE OF CONTENTS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill liquid of any kind on or into this product. Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/ or product at any time and without notice. PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: ANI-PIP 4x1 HDMI Seamless Quad PiP Scaler Remote Control (ANI-124) Rackmount Brackets 12V/3A DC Power Adaptor Users Guide COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise without the express written permission and consent. Copyright All Rights Reserved. Version 3.3 JAN 2017 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. 1

4 FEATURES & SPECIFICATIONS FEATURES The ANI-PiP HDMI Seamless Quad PiP Multiviewer allows you to simultaneously display up to (4) different sources on a single display. Each of the quadrants can be adjusted to any size and positioned to any location on the display. Quad, Picture in Picture, Picture over Picture, Full Screen and custom display modes Seamless switching between sources Custom Display Mode: Size, position and selection of any or all windows are customizable (8) pre-stored configuration hot keys and plus (4) customized favorite screen settings Drag-n-Drop GUI interface for fast and easy changes to the screen layout Supports HDTV resolutions up to 1080p and computer resolutions to 1920x1200 Bandwidth up to 165MHz (2.0625Gbps) HDCP compliant Fluid, real-time video performance with (60) frames per second (fps) in all (4) quadrants Switches audio independently for video from the connected HDMI sources Control the ANI-PiP through Ethernet, RS-232 serial port, on screen display (OSD), front panel buttons or IR remote Fade-In-Out, Chroma key, Mirror and Rotation (90 left & right and 180 up & down) functions Cascades ANI-PiP to display video from up to (16) video sources on one screen. (Each unit in the cascade must be configured and controlled individually) Mounts using the included rack mount bracket or use as a desktop SYSTEM REQUIREMENTS Input source equipment such as DVD/Blu-ray players and PC/NB devices and output HDTV/monitors SPECIFICATIONS Video Bandwidth: 225MHz/6.75Gbps Input Port: (4) HDMI Output Port: (1) HDMI ESD Protection: Human body model: ±8kV (air-gap discharge) / ±4kV (contact-gap discharge) Power Supply: 12V/3A DC (US/EU standards, CE/FCC/UL certified) Dimensions (WxDxH): 17 x 9.9 x 1.73 in Weight: 46.2 lb (Unit only) / 8.6 lb (Net) Chassis Material: Aluminum Silkscreen Color: Black Operating Temperature: 32 F~104 F (0 C~40 C) Storage Temperature: -4 F~140 F (-20 C~60 C) Relative Humidity: 20~90% RH (non-condensing) As product improvements are continuous, specifications are subject to change without notice. 2

5 OPERATION CONTROLS & FUNCTIONS Front Panel q IR WINDOW: Accepts IR signal from the device s remote control (included) w POWER: Press this button to power on the device or set it to standby mode e MENU: Press this button to bring up the OSD menu on screen r -/+ BUTTONS: Press these buttons to scroll down/up the OSD selections t CHANNEL INPUT 1~4: Press these buttons to cycle thru HDMI 1~4 input sources as assigned to each window y WINDOW A~H: Press these hot keys to select the screen setting where A~D display a full screen of each channel and E~H are a different combination of a full screen setting with all (4) channels (Quad view) BACK Panel q HDMI IN: Connects with source equipment such as DVD, Blu-ray players, Computers, Apple TV, etc. w HDMI OUT: Connects with a HDTV/monitor for output image display e RJ45 JACK: Ethernet jack for switcher control using telnet control r USB SERVICE ONLY: This slot is reserved for factory use only t RS-232: Connects from the PC/NB with D-Sub 15pin cable for RS-232 control y DC 12V: Plug the 12V DC power supply into the unit and connect the adaptor to an AC outlet 3

6 Remote Control REMOTE CONTROL q POWER: Press this button to switch on the device or press it again to set it to standby mode w INFO: Press this button to show the device s firmware version e INPUT CH 1~4: Press these buttons to rotate the HDMI 1~4 input sources on each channel to be displayed on screen r WA~WH: Press these hot keys to select the screen setting where A~D display a full screen of each channel and E~H are a different combination of the full screen setting with all (4) channels t MUTE: Press this button to mute the audio from HDMI output port y & OK BUTTONS: Press these buttons to scroll through the OSD selections and press OK to enter and confirm the setting u MENU: Press this button to enter into the OSD menu i EXIT: Press this button to exit the OSD menu or the OSD settings o FAV. 1~4: Press these buttons to bring up the customized screen settings a FADE-IN-OUT*: Press this button to switch On or Off the Fade-In-Out function s CHROMAKEY*: Press this button to enter into Chroma function where CH 1 is the background and CH 2 is the top image d MIRROR*: Press this button to display the screen in mirror image f ROTATION*: Press this button to rotate the image 90 left and right or 180 upside down g AUDIO 1~4: Press these buttons to select audio from the HDMI inputs 1~4 * Functions only work under Window A to D. The system will force switch to Window A when current operation is Window E~H. 4

7 IR CODES IR CODES CUSTOM CODE: 807F POWER TOGGLE: 807F 82 CHANNELS: INFO: 807F 86 CH1: 807F 8A MUTE: 807F C2 CH2: 807F 8E UP: 807F 9A CH3: 807F 92 DOWN: 807F 9E CH4: 807F C6 LEFT: 807F 9C RIGHT: 807F 98 AUDIO SETTINGS: OK: 807F 9D AUDIO1: 807F 87 EXIT: 807F D8 AUDIO2: 807F C4 MENU: 807F 84 AUDIO3: 807F C5 FADE IN-OUT: 807F 8F AUDIO4: 807F D9 CHROMEKEY: 807F CC MIRROR: 807F CD FAVORITE SETTINGS: ROTATION: 807F CE FAV.1: 807F 97 FAV.2: 807F D4 SCREEN SETTINGS: FAV.3: 807F D5 WA: 807F 88 FAV.4: 807F D6 WE: 807F 89 WB: 807F 8C WF: 807F 8D WC: 807F 90 WG: 807F 91 WD: 807F 85 WH: 807F 95 5

8 Timing Supported Timing Supported INPUT TIMING SUPPORTED VGA60 VGA72 VGA75 VGA85 WXGA60 WXGA75 DTV_480p60 DTV_576p50 DTV_480i60 DTV_576i50 HDTV_720p50 HDTV_720p60 HDTV_1080i60 HDTV_1080i50 HDTV_1080p24 HDTV_1080p50 HDTV_1080p60 XGA60 OUTPUT TIMING SUPPORTED 480p 59Hz 576p 50Hz 720p 50Hz 720p 60Hz 1080p 24Hz 1080p 25Hz 1080p 30Hz 1080p 50Hz 1080p 60Hz 1024x768 60Hz 1280x800 60Hz 1280x Hz 1366x768 60Hz 1440x900 60Hz 1600x900RB 60Hz 1600x Hz 1680x Hz 1920x1200RB 60Hz XGA70 XGA75 XGA85 SXGA60 SXGA75 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 V1360_768_60 V1366_768_60 V1600_1200_60 V1920_1200_60 6

9 RS-232 Protocols RS-232 Protocols ANI-PiP REMOTE CONTROL PIN ASSIGNMENT PIN ASSIGNMENT 1 NC 1 NC 2 Tx 2 Rx Baud Rate: bps Data Bit: 8bits Parity: None Flow Control: None Stop Bit: 1 3 Rx 3 Tx 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC RS-232 Commands COMMAND CODE DESCRIPTION SYNTAX EXAMPLE ACTIVE RESO OSDDIS SETS OUTPUT RESOLUTION ENABLE/DISABLE ONSCREEN DISPLAY RESO PARAM1 PARAM1 = 0-18 OSDDIS PARAM1 PARAM1 = 0-1 (0-OFF, 1-ON) OSDH OSD H OFFSET OSDH PARAM1 PARAM1 = 0-20 OSDV OSD V OFFSET OSDV PARAM1 PARAM1 = 0-20 OSDGAIN OSD GAIN VALUE OSDGAIN PARAM1 PARAM1 = 0-10 BRI SETS BRIGHTNESS VALUE FOR CHANNEL BRI PARAM1 PARAM2 PARAM1 = 0 (ALL) PARAM1 = 1-4 (CHANNEL) PARAM2 = (VALUE) RESO 5 OSDDIS 0 OSDDIS 1 0 IS SET TO 1 IS SET TO 2 IS SET TO 3 IS SET TO 4 IS SET TO 5 IS SET TO 6 IS SET TO 7 IS SET TO 8 IS SET TO 9 IS SET TO 10 IS SET TO 11 IS SET TO 12 IS SET TO 13 IS SET TO 14 IS SET TO 15 IS SET TO 16 IS SET TO 17 IS SET TO 18 IS SET TO 480p 576p 720p 50Hz 720p 60Hz 1080p 24Hz 1080p 25Hz 1080p 30Hz 1080p 50Hz 1080p 60Hz 1024x768 60Hz 1280x800 60Hz 1280x Hz 1366x768 60Hz 1440x900 60Hz 1600x900 60Hz 1600x Hz 1680x Hz 1920x Hz Native OSD INFO IS SET TO OFF OSD INFO IS SET TO ON OSDH 10 OSD H OFFSET 10% OSDV 10 OSD V OFFSET 10% OSDGAIN 10 OSD GAIN VALUE IS 10 BRI 0 50 BRI 1 50 ALL CHANNEL SET TO BRIGHTNESS VALUE 50 CHANNEL 1 IS SET TO BRIGHTNESS VALUE 50 7

10 RS-232 Protocols COMMAND CODE DESCRIPTION SYNTAX EXAMPLE ACTIVE CON SAT HUE HSIZE VSIZE HPOS VPOS IMAGE PRI LABEL STORE SETS CONTRAST VALUE FOR CHANNEL PORT SETS SATURATION VALUE FOR CHANNEL PORT SETS HUE VALUE FOR CHANNEL PORT SETS IMAGE HORIZONTAL SIZE SETS IMAGE VERTICAL SIZE SETS HORIZONTAL POSITION OF SPECIFIED CHANNEL SET VERTICAL POSITION OF SPECIFIED CHANNEL CHANNEL(S) OUTPUT ON/OFF SET CHANNEL PRIORITY ASSIGN A VIDEO NAME SAVES THE CURRENT WINDOW STATE TO FAV. CON PARAM1 PARAM2 PARAM1 = 0 (ALL) PARAM1 = 1-4 (CHANNEL) PARAM2 = (VALUE) SAT PARAM1 PARAM2 PARAM1 = 0 (ALL) PARAM1 = 1-4 (CHANNEL) PARAM2 = (VALUE) HUE PARAM1 PARAM2 PARAM1 = 0 (ALL) PARAM1 = 1-4 (CHANNEL) PARAM2 = (VALUE) HSIZE PARAM1 PARAM2 PARAM1 = 1-4 (CHANNEL) PARAM2 = 0-X (X=HORIZONTAL PIXEL FOR CURRENT RES) VSIZE PARAM1 PARAM2 PARAM1 = 1-4 (CHANNEL) PARAM2 = 0-X (X = VERTICAL PIXEL FOR CURRENT RES) HPOS PARAM1 PARAM2 PARAM1 = 1-4 (CHANNEL) PARAM2 = 0-X (X = HORIZONTAL PIXEL FOR CURRENT RES) VPOS PARAM1 PARAM2 PARAM1 = 1-4 (CHANNEL) PARAM2 = 0-X (X = VERTICAL PIXEL FOR CURRENT RES) IMAGE PARAM 1 PARAM 2 PARAM1 = 1-4 (CHANNEL) PARAM2 = 0-1 (0-OFF, 1- ON) PRI PARAM1 PARAM2 PARAM1 = 1-4 (CHANNEL) PARAM2 = 1-4 (PRIORITY) LABEL PARAM 1 PARAM 2 PARAM 1 = 1-4 (VIDEO) PARAM 2 = ABCDEFGH STORE PARAM 1 PARAM 1 = 1-4 (FAV.) CON 0 50 CONT 1 50 SAT 0 50 SAT 1 50 HUE 0 50 HUE 1 50 HSIZE VSIZE HPOS VPOS IMAGE 1 0 ALL CHANNEL SET TO CONTRAST VALUE 50 CHANNEL 1 IS SET TO CONTRAST VALUE 50 ALL CHANNEL SET TO SATURATION VALUE 50 CHANNEL 1 IS SET TO SATURATION VALUE 50 ALL CHANNEL SET TO HUE VALUE 50 CHANNEL 1 IS SET TO HUE VALUE 50 SET HORIZONTAL STRETCH VALUE TO 1080 PIXELS FOR CHANNEL 1 SET VERTICAL STRETCH VALUE TO 1920 PIXELS FOR CHANNEL 2 SET HORIZONTAL POSITION VALUE TO 1080 PIXELS FOR CHANNEL 1 SET VERTICAL POSITION VALUE TO 1920 PIXELS FOR CHANNEL 2 CHANNEL 1 IS OFF PRI 1 3 CHANNEL 1 SET TO PRIORITY 3 LABEL 1 Blu-ray STORE 3 Blu-Ray NAME IS ASSIGNED TO VIDEO 1 CURRENT WINDOW STATE IS SAVED TO FAV. 3 8

11 RS-232 Protocols COMMAND CODE DESCRIPTION SYNTAX EXAMPLE ACTIVE RECALL MIRROR ROTATE CHRSW FADE CHRC IPMODE RECALLS A WINDOW STATE ENABLE/DISABLE MIRROR EFFECT SETS VIDEO ROTATION VIDEO TO PRESET POSITIONS SETS THE CHROMA KEY ON/OFF ENABLE/DISABLE FADE EFFECTS SETS THE RGB COLOR RANGE FOR THE CHROMA KEY SETS IP MODE TO DHCP OR STATIC RECALL PARAM 1 PARAM 1 = 1-2 (WINDOW) MIRROR PARAM1 PARAM1 = 0-1 (0-OFF, 1-ON) ROTATE PARAM1 PARAM1 = 0-3 (0-ROTATE OFF,1-R90, 2-L90, 3-180) CHRSW PARAM1 PARAM1 = 0-1 (0-OFF, 1-ON) FADE PARAM1 PARAM1 = 0-21# CHRC PARAM1 PARAM2 PARAM3 PARAM1 = R/G/B (Color channel) PARAM2 = MIN/MAX (Color value) PARAM3 = 0-15 (SET PRESET VALUE 0-255) IPMODE PARAM1 = 0-1 (0-DHCP; 1-STATIC) RECALL 1 RECALL 2 RECALL 3 RECALL 4 RECALL 5 RECALL 6 RECALL 7 RECALL 8 RECALL 9 RECALL 10 RECALL 11 RECALL 12 MIRROR 0 MIRROR 1 ROTATE 1 CHRSW 1 #FADE 0 #FADE 1 #FADE 2 #FADE 3 #FADE 4 #FADE 5 #FADE 6 #FADE 7 #FADE 8 #FADE 9 #FADE 10 #FADE 11 #FADE 12 #FADE 13 #FADE 14 #FADE 15 #FADE 16 #FADE 17 #FADE 18 #FADE 19 #FADE 20 #FADE 21 CHRC R MIN 10 IPMODE 0 IPMODE 1 RECALLED THE WINDOW A RECALLED THE WINDOW B RECALLED THE WINDOW C RECALLED THE WINDOW D RECALLED THE WINDOW E RECALLED THE WINDOW F RECALLED THE WINDOW G RECALLED THE WINDOW H RECALLED THE WINDOW FAV. 1 RECALLED THE WINDOW FAV. 2 RECALLED THE WINDOW FAV. 3 RECALLED THE WINDOW FAV. 4 MIRROR EFFECT OFF MIRROR EFFECT ON ROTATE VIDEO SET TO R90 CHROMA KEY SWITCH ON FADE EFFECT OFF FADE EFFECT 1.0 s FADE EFFECT 1.1 s FADE EFFECT 1.2 s FADE EFFECT 1.3 s FADE EFFECT 1.4 s FADE EFFECT 1.5 s FADE EFFECT 1.6 s FADE EFFECT 1.7 s FADE EFFECT 1.8 s FADE EFFECT 1.9 s FADE EFFECT 2.0 s FADE EFFECT 2.1 s FADE EFFECT 2.2 s FADE EFFECT 2.3 s FADE EFFECT 2.4 s FADE EFFECT 2.5 s FADE EFFECT 2.6 s FADE EFFECT 2.7 s FADE EFFECT 2.8 s FADE EFFECT 2.9 s FADE EFFECT 3.0 s CHROMA KEY VALUE FOR R MIN SET TO 160 IP MODE SET TO DHCP IP MODE SET TO STATIC A REBOOT IS REQUIRED TO APPLY CHANGES 9

12 RS-232 Protocols COMMAND CODE DESCRIPTION SYNTAX EXAMPLE ACTIVE IPMODE SETS IP MODE TO DHCP OR STATIC IPMODE PARAM1 = 0-1 (0-DHCP; 1-STATIC) IPADD SETS IP ADDRESS IPADD PARAM1 PARAM1 = XXX.XXX.XXX.XXX WHERE XXX: MAADD GAADD SETS SUBNET ADDRESS SETS GATEWAY ADDRESS MAADD PARAM1 PARAM1 = XXX.XXX.XXX.XXX WHERE XXX: GAADD PARAM1 PARAM1 = XXX.XXX.XXX.XXX WHERE XXX: ETHTIME ETHERNET TIMEOUT ETHTIME PARAM1 PARAM1 = 0-6 RELINK RELINK THE UNIT RELINK NO PARAMETER DEFAULT VICH RESET THE UNIT TO FACTORY DEFAULTS VIDEO CHANNEL COMMAND DEFAULT NO PARAMETER VICH PARAM1 PARAM2... PARAM4 PARAM1 = 1-4 (VIDEO) PARAM2 = 0 (ALL CHANNEL OUTPUTS) PARAM2...PARAM 4 = 1-4 (CHANNEL OUTPUTS) MUTE MUTE AUDIO MUTE PARAM1 PARAM1 = 0-1 (0-OFF, 1-ON) POW AUDIO IMRE PIRE WICORE POWER THE UNIT ON/OFF CHANGE OUTPUT AUDIO TO SPECIFIED SOURCE RESET THE IMAGE TO FACTORY DEFAULTS RESET THE UNIT PICTURE SETTINGS TO FACTORY DEFAULTS RESET THE WINDOW CONVERT TO FACTORY DEFAULTS POW PARAM1 PARAM1 = 0-1 (0-OFF, 1-ON) AUDIO PARAM1 PARAM1 = 1-4 (AUDIO SOURCE) IMRE PARAM1 PARAM1 = B (BRIGHTNESS) PARAM1 = C (CONTRAST) PARAM1 = S (SATURATION) PARAM1 = H (HUE) IPMODE 0 IPMODE 1 IPADD MAADD GAADD ETHTIME 0 ETHTIME 1 ETHTIME 2 ETHTIME 3 ETHTIME 4 ETHTIME 5 ETHTIME 6 RELINK DEFAULT VICH 1 1 VICH 1 0 MUTE 0 MUTE 1 POW 1 POW 0 AUDIO 2 IMRE B IP MODE SET TO DHCP IP MODE SET TO STATIC A REBOOT IS REQUIRED TO APPLY CHANGES IP ADDRESS IS: PLEASE REBOOT THE UNIT TO APPLY CHANGES NETMASK ADDRESS IS: PLEASE REBOOT THE UNIT TO APPLY CHANGES GATEWAY ADDRESS IS: PLEASE REBOOT THE UNIT TO APPLY CHANGES ETHERNET TIMEOUT IS OFF ETHERNET TIMEOUT IS 10 MINUTES ETHERNET TIMEOUT IS 20 MINUTES ETHERNET TIMEOUT IS 30 MINUTES ETHERNET TIMEOUT IS 40 MINUTES ETHERNET TIMEOUT IS 50 MINUTES ETHERNET TIMEOUT IS 60 MINUTES UNIT WILL RE-LINK IN 2 SECONDS UNIT IS SET TO FACTORY DEFAULTS VIDEO 1 IS ROUTED TO CHANNEL OUTPUT 1 VIDEO 1 IS SET TO ALL CHANNEL OUTPUTS AUDIO IS UNMUTED AUDIO IS MUTED POWER IS ON POWER IS OFF AUDIO SOURCE 2 IS SELECTED BRIGHTNESS VALUE SET TO FACTORY DEFAULTS FOR ALL INPUTS PIRENO PARAMETER PIRE PICTURE SET TO FACTORY DEFAULTS FOR ALL INPUTS WICORE NO PARAMETER WICORE WINDOW CONVERT SET TO FACTORY DEFAULTS 10

13 RS-232 Protocols COMMAND CODE DESCRIPTION SYNTAX EXAMPLE ACTIVE CHRE RIPM IPCONFIG HELP RESET THE WINDOWS SETTINGS TO FACTORY DEFAULTS SHOW CURRENT IP MODE SHOW IP CONFIGURATION PRINTS ALL AVAILABLE RS-232/ TELNET COMMANDS TO THE SCREEN? PRINTS ALL AVAILABLE RS-232/ TELNET COMMANDS TO THE SCREEN CHRE PARAM1 PARAM1= 0 (ALL CHANNEL OUTPUTS) PARAM1 = 1-4 (CHANNEL OUTPUTS) CHRE 1 CHANNEL 1 SET TO FACTORY DEFAULTS NO PARAMETER RIPM IP MODE SET TO DHCP IP MODE SET TO MANUAL NO PARAMETER IPCONFIG IP: xxx.xxx.xxx.xxx MASK: xxx.xxx.xxx.xxx GATE: xxx.xxx.xxx.xxx NO PARAMETERS HELP AVAILABLE COMMANDS NO PARAMETERS? AVAILABLE COMMANDS

14 OSD MENU OSD MENU MAIN MENU I/O Setup Image Adjust Windows Setup Window Convert Chromakey Setup Ethernet Setup Sys Reset No/Yes Information Menu Exit I/O Setup SUB ADVANCE ADVANCE I/O SETUP Output Resolution OUTPUT RESOLUTION OSD Settings 480p OSD SETTINGS Menu Exit 576p Info Display On/Off 720p50 Offset 0~20 720p p24 V Offset 0~ p25 Timeout Off~ p30 Gain 0~ p p x x x x x x x x x1200 NATIVE Menu Back Menu Back 12

15 OSD MENU Image Adjust SUB ADVANCE ADVANCE ADVANCE ADVANCE IMAGE ADJUST Brightness BRIGHTNESS ADJUST Contrast CH 1 0~100 CONTRAST ADJUST Saturation CH 2 0~100 CH 1 0~100 SATURATION ADJUST Hue CH 3 0~100 CH 2 0~100 CH 1 0~100 HUE ADJUST Picture Reset CH 4 0~100 CH 3 0~100 CH 2 0~100 CH 1 0~100 Menu Exit Value Reset CH 4 0~100 CH 3 0~100 CH 2 0~100 Menu Exit Value Reset CH 4 0~100 CH 3 0~100 Menu Exit Value Reset CH 4 0~100 Menu Exit Value Reset Menu Exit Windows Setup SUB ADVANCE ADVANCE1 ADVANCE1 WINDOWS SETUP Channel 1 Select CHANNEL (1~4) Channel 2 Select SELECT Channel 3 Select Size SIZE ADJUST Channel 4 Select Position CH (1~4) Wxxxx Hxxxx POSITION ADJUST Label Select Image Output On/Off Width Unit CH (1~4) Wxxxx Hxxxx Favorites Store Priority 1~4 Width Ten Horizontal Unit Menu Exit Window Reset Width Hundred Horizontal Ten Menu Exit Height Unit Horizontal Hundred Height Ten Height Hundred Value Reset Menu Exit Vertical Unit Vertical Ten Vertical Hundred Value Reset Menu Exit 13

16 OSD MENU SUB ADVANCE ADVANCE1 WINDOWS SETUP Channel 1 Select Channel 2 Select Channel 3 Select Channel 4 Select Label Select LABEL SELECT Favorites Store VIDEO 1 XXXXXXXXX VIDEO (1~4) LABEL Menu Exit VIDEO 2 XXXXXXXXX XXXXXXXXX VIDEO 3 XXXXXXXXX Menu Exit VIDEO 4 XXXXXXXXX Menu Exit SUB WINDOWS SETUP ADVANCE Channel 1 Select Channel 2 Select Channel 3 Select Channel 4 Select Label Select Favorites Store FAVORITES STORE Menu Exit FAV1 Store NO/OFF/OK FAV2 Store FAV3 Store FAV4 Store NO/OFF/OK NO/OFF/OK NO/OFF/OK Menu Exit Channel X Convert SUB CHANNEL X CONVERT Mirror On/Off Fade In-Out off~3 Rotation R90/L90/180/Off Window Reset Menu Exit 14

17 OSD MENU Chromakey Setup SUB CHROMAKEY SETUP Minimum For R 000~255 Maximum For R 000~255 Minimum For G 000~255 Maximum For G 000~255 Minimum For B 000~255 Maximum For B 000~255 Switch On/Off 000~255 Menu Exit Ethernet Setup SUB ETHERNET SETUP IP Mode Static Set Static/DHCP IP/Mask/Gate Byte1 High XXX 000~255 Byte2 XXX 000~255 Byte3 XXX 000~255 Byte4 Low XXX 000~255 Re-Link No/Yes Exit Static /DHCP IP IP Mask Gate Mac LINKED/NOT LINKED XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX XXXXXX XXXXXX Information SUB INFORMATION Sink HDMI/DVI Model xxxxxxxxxx Native xxxxxxxxxx FW Vx.xx Menu Exit ANI-PIP OSD MAP V2.05(140618) 15

18 WEB GUI IMAGE ADJUST OUTPUT RESOLUTION 16

19 WEB GUI OSD SETTING WINDOW CONVERT 17

20 WEB GUI CHORMAKEY SETUP ETHERNET 18

21 WEB GUI QUAD VIEW E QUAD VIEW F 19

22 WEB GUI QUAD VIEW G QUAD VIEW H 20

23 CONNECTION & INSTALLATION 21

24 TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE PRODUCT ). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you. RESTRICTIONS ON USE OF THE PRODUCT It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage. The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, A-NeuVideo ) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product. The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo. The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls. DISCLAIMERS AND LIMITATION OF LIABILITY A-NeuVideo may change or modify the Product at any time, from time to time. THE PRODUCT IS PROVIDED AS IS AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product. TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO. UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT. END OF DOCUMENT 22