DXP A0808 Quick Start

Transcription

1 VIEWSIZE THE WORLD DXP A0808 Quick Start Support any in any out Support independent output switching Support infrared remote control Input and output can be modularized RS 232 loop out for multiple control Support EDID management

2 CONTENT Product Introduction... 2 Packing Configuration... 3 Hardware Orientation... 4 Front Panel... 4 Back Panel... 5 Operating Instruction... 6 Content... 6 How to Switch between Input and Output Channel... 7 How to Switch One Input to all Outputs... 7 How to Close One Output Channel... 7 How to Close all Output Channels... 8 How to Set One-to-one Correspondence for Input and Output Channel... 8 How to Save Pre-set Input and Output Channel... 8 How to Call Pre-set Input and Output Channel Saving Mode... 9 How to Factory Reset... 9 How to Read Equipment Related Information... 9 How to Set LOGO Display when Power on Contact Information

3 Product Introduction Matrix switching system is the whole cross high performance device, used for signal switching. Mainly used in television broadcasting system signal switching and exchange, multimedia meeting room, large screen projection display engineering, government conference room, hospital medical discussion conference room, television signal switching, interactive multimedia classrooms, and military command video conference room. RGBlink strong technical strength determines the high quality of AVDXP series matrix switchers. We choose the chips with best performance, elaborate design for every way of switchers, to ensure the high quality of switchers. After rigorous testing, VGA switching signal bandwidth is 500 MHz (-3db), support resolution of to fully meet various strict requirements and high quality occasions. Video for 250MHz (-3db), can not only support various of video signals, but also meet the future high-definition television (HDTV) bandwidth requirements. RGBlink matrix switchers provide the good man-machine interface for users. Switchers in this series are equipped with monochromatic LCD, RS 232 communication interface, with outage protect function, can read and store up to 24 user scenarios. The system is equipped with multiple sets of serial instructions, can in conjunction with computer, remote control system or all kinds of distal control equipment. System Connection RGBlink offers solutions to demanding technical problems. Any application questions, or required further information, please contact with our customer Support Engineers. DXP A0808 System Connection Diagram 2

4 Packing Configuration Power Cord 9-pin Serial Cable USB Disk Screw Driver Antistatic Bag Certification Note: Chinese Standard, American Standard or European Standard power cord is option. The color of the screw driver is randomly when packing. 3

5 Hardware Orientation Front Panel Button Instruction 0~8 Selection button for input and output channel, and number choice of save or call saving modes. [0] button can also be used to shut down the channel output. Rec Load button 20+ UP arrow button and decimal button Save Save button 30+ Down arrow button Esc Exit button ALL Distributor selection button LED Power indicator F1. F2 Fast call user save mode indicator Mode indicator Menu Menu button Com indicator Mode Audio and video switching button IR receiver Receive the infrared signal Enter Confirm button LCD Panel Show operation menu items 4

6 Back Panel Input Interface 1 CVBS Input BNC port Output Interface 2 CVBS Output BNC port Other Interface 3 RS 232 IN serial communication interface 4 RS 232 OUT serial communication interface 5 Switch 6 Power IEC-3 port 5

7 Operating Instruction Content How to Switch between Input and Output Channel How to Switch One Input to all Outputs How to Close One Output Channel How to Close all Output Channels How to Set One-to-one Correspondence for Input and Output Channel How to Save Pre-set Input and Output Channel How to Call Pre-set Input and Output Channel Saving Mode How to Factory Reset How to Read Equipment Related Information How to Set LOGO Display when Power on 6

8 How to Switch between Input and Output Channel DXP A0808 can rapidly switch any way signals by the front panel buttons, specific operations are as follows: 1. Push the number button to select the input channel, for example, push the button [3]. 2. Push the number button again to select the output channel, for example, push the button [5]. 3. After selection, push the button [Enter] to confirm. Note: Input channel: The signal that will be switched to output channel. Output channel: The signal that connected to display device. The number [1]~[8] means channel 1~8. How to Switch One Input to all Outputs 1. Push the number button, for example, push the button [2]. 2. Then push the button [ALL], and input 2 will be switched to all outputs. User can also operate by the following ways: 1. Push the button [ALL]. 2. Then choose the input channel, for example, push the button [2]. 3. Push the button [Enter] to confirm. How to Close One Output Channel 1. Push the button [0] on the front panel. 2. Choose output channel, for example, push the button [8]. 3. Push the button [Enter] to confirm. 7

9 How to Close all Output Channels 1. Push the button [0] on the front panel. 2. Then push the button [ALL] on the front panel. User can also operate by the following ways: 1. Push the button ALL on the front panel. 2. Push the button 0 on the front panel. 3. Push the button [Enter] to confirm. How to Set One-to-one Correspondence for Input and Output Channel 1. Push the button [Rec] on the front panel. 2. Push the button [0] on the front panel. 3. Push the button [Enter] to confirm. How to Save Pre-set Input and Output Channel 1. Push the button [Save] on the front panel. 2. User can choose 24 kinds of mode from button [1]~[24], for example, push the button [2]. 3. Push the button [Enter] to confirm. 8

10 How to Call Pre-set Input and Output Channel Saving Mode 1. Push the button [Rec] on the front panel. 2. User can choose 25 kinds of mode from button [0]~[24], for example, push the button [7]. 3. Push the button [Enter] to confirm. Note: [0] is default for one-to-one correspondence for input and output way. That is input [1] is corresponding to output [1], input [2] is corresponding to output [2] How to Factory Reset 1. Push the button [Menu] on the front panel. 2. Push the button [30+] DOWN arrow button, or button [20+] UP arrow button, make RESET option for selected state. 3. Push the button [Enter] to confirm and enter the initialization interface. 4. Push any button according to the LCD hint and complete factory reset. How to Read Equipment Related Information 1. Push the button [Menu] on the front panel. 2. System default STATUS option, if it is not selected, push the [30+] DOWN arrow button or [20+] UP arrow button and choose <STATUS>. 3. Push the button [Enter] to confirm, read the information by the [30+] DOWN arrow button or [20+] UP arrow button. 9

11 How to Set LOGO Display when Power on 1. Push the button [MENU] on the front panel. 2. Push the [30+] DOWN arrow button or [20+] UP arrow button and select <LOGO>. 3. Push the button [Enter] to confirm, and enter LOGO switch setting, LOGO ON or OFF at boot can be set. 10

12 Contact Information Warranty: All video products are designed and tested to the highest quality standard and backed by full 3 years parts and labor warranty. Warranties are effective upon delivery date to customer and are non-transferable. RGBlink warranties are only valid to the original purchase/owner. Warranty related repairs include parts and labor, but do not include faults resulting from user negligence, special modification, lighting strikes, abuse (drop/crush), and/or other unusual damages. The customer shall pay shipping charges when unit is returned for repair. Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C Tel: Fax: Customer Hotline: Web: ~ ~ support@rgblink.com 11