42 Freestanding Infrared Multi Touch Screen Kiosk User s Manual

Transcription

1 42 Freestanding Infrared Multi Touch Screen Kiosk User s Manual Manual Version L42HD-T2.2

2 Safety Instructions Please keep the display away from any heat sources such as radiators or direct sunlight. Place the display in a stable and well-ventilated place. Please handle with care as product contains glass. The holes or openings on the display are designed for ventilation. Do not cover or block the ventilation holes or openings. Remove protective covering from the screen before you use the display. As the display surface is vulnerable to scratches, avoid touching the surface with sharp pen point. Shut off the power supply before cleaning. Use a soft lint-free cloth instead of a tissue to wipe the screen. You may use a glass cleaner to clean the product as required. However, never spray the cleaner directly onto the display surface. Do not attempt to repair this product yourself! Improper disassembly of the product will invalidate the warranty and could be dangerous. If you have a problem that cannot be solved using the "Troubleshooting" guidelines, please contact your supplier. Page 1

3 Quick Start Guide This section of the guide allows quick setup and use of the unit. Please refer to the main part of the User Guide for full information on use of the unit. Please follow the steps detailed below: 1. Unpack unit and place in desired location and place PC inside. 2. Power ON the PC using the power extension inside the locker door. 3. Take the power lead from the accessories bag, insert the lead into the screen and connect to mains outlet. The unit will power ON automatically. 4. Connect the screen to the PC via the HDMI Cable and link the screen s Infrared touch sensors to the PC via the USB cable (as shown below). Once you insert the USB cable into your PC it should install the necessary driver automatically. Figure 1 Screen to PC Connections 5. The screen should now be acting as a monitor and allowing you to use your finger as a mouse on the screen displaying the PC s contents. Page 2

4 Contents: 1. Introduction Box Contents Product Overview Serial Control Box Connection to the screen Serial Control Box Overview Remote Control Replacing the Remote Control Battery Menu Operation Inputs Set Up Connecting to PC F.A.Qs and Troubleshooting Guide My Touch Screen is not displaying what is on my PC Input Source Display/monitor button on keyboard My display turns itself OFF when it s not connected to my PC Power saving function My screen is displaying video signal but touch function is disabled My Remote control is not working Page 3

5 Table of Figures Figure 1 Screen to PC Connections... 2 Figure 2 Product Overview... 5 Figure 3 Serial Control Box inside locker door... 6 Figure 4 Serial Control Box inside locker door Figure 5 Screen Inputs... Error! Bookmark not defined. Figure 6 Screen to PC Connections Page 4

6 1. Introduction Congratulations on your purchase of our product. Please read carefully and follow all instructions in the manual before first use. The product should not be exposed to liquids dripping or splashing and no liquid filled objects, such as vases, should be placed on the product. For user convenience, a number of operations can be performed through the remote control. Attention: 1. Do not change any default settings unnecessarily 2. Keep the product far away from water during installation and use. 1.1 Box Contents 1xFreestanding Infrared Touch Screen Kiosk 1xHDMI Cable (Attached) 1xVGA Cable (Attached) 1xUSB Cable (Attached) 1xCD (User Manual) 1xRemote Control 1xSerial Control Box (Attached) 1.2 Product Overview Figure 2 Product Overview Page 5

7 1.3 Serial Control Box Connection to the screen The screen s remote control IR sensor can be found on the silver control box hanging from the main inputs inside the locker door. This control box can also be used as a secondary remote control as it features some basic controls to access the menu. Figure 3 Serial Control Box inside locker door Page 6

8 1.3.2 Serial Control Box Overview Button Function Right navigation button adjust volume MENU INPUT Left navigation button Open/close OSD menu or return to previous menu Select signal input Signal input select select in OSD menu select signals input adjust values Page 7

9 1.4 Remote Control Page 8

10 1.5 Replacing the Remote Control Battery 1. Slide the battery cover off, as shown below. 2. Remove the used batteries. 4. Insert the two new AAA batteries with their terminals corresponding to the indicators. 5. Put the cover back on. Page 9

11 1.6 Menu Operation The Menu includes the following menus: Picture, Sound, Time and Option. Figure 4 Serial Control Box inside locker door Pointing your remote control at the silver control box inside the locker door press MENU to bring up the menus, press to select the desired menu and to select the desired item, press PLAY to confirm selection. Press menu at any time to go back or exit. Page 10

12 Picture Here is where you can edit settings such as brightness, contrast, colour temperature and backlight brightness. Any settings that you change can be reset back to default at any time. Picture Mode <Standard> or Mild/User/Auto/Dynamic User Contrast Brightness Colour Sharpness Tint Color Temperature <Medium> or Warm/User/Cool Aspect Ratio Noise Reduction PC Setup Backlight <100> or Sound In this menu you can adjust all of the sound settings for your monitor such as the sound mode EQ settings or the left/right balance. Any settings that you change can be reset back to default at any time. Sound Mode <Standard> or Music/Movie/Sports/User Balance <0> -50(left) to +50(right) Auto Volume <Off> or On Surround Sound <Off> or Surround EQ 120 Hz 500 Hz 1.5K Hz 5K Hz 10K Hz Page 11

13 Time Here you can set a time and date for your screen as well as scheduling daily on/off times for the built in power timer. You can also adjust at what temperature the internal fans become active. Clock <DATE and TIME> Date Month Year Hour Minute Off Time <Off> Hour Minute On Time <Off> Hour Minute Temperature XX (Current screen temperature) Fan Active <30> (Temperature when internal fans become active) Page 12

14 Option Under this menu are settings like on screen display language, on screen display duration time, and the video wall tiling settings. You can also restore all of the menus default settings and lock your screen so as you have to enter a password to access any of the menus. OSD Language <English> or Franais/Espanol/ Poruguês/Arabic/ 中文 Restore Default Setting (Resets menu settings to default) Blending <Low> or Middle/High/Off OSD Duration <Off> or 5sec/10sec/15sec Multi Setup Multi Crop Copy Start Board ID Current X Current Y Total X Total Y Left Edge Up Edge Right Edge Down Edge Lock System <Off> or On (Password 1842) Page 13

15 Switching between inputs One crucial feature that does not appear on the Main Menu is selecting the input source. This is done by first pressing SOURCE and then scrolling down to the desired input source and select by pressing PLAY. PC-RGB PC-RGB (BNC) COMPONENT DVI HDMI AV1 AV2 DMP 1.7 Inputs VGA (PC-RGB) Video Graphics Array Signal Input HDMI High Definition Multimedia Interface Signal Input USB Universal Serial Bus (for touch screen panel) Page 14

16 2. Set Up 2.1 Connecting to PC There is space inside the unit for a small form factor PC. The touch screen must be connected to the PC in two ways: visually and interactively. The recommended visual connection is via the HDMI Cable (included) meaning that the display acts like a monitor for the PC. The touch function is achieved by linking the Infrared touch sensors around the screen to the PC via the USB Cable inside. Figure 5 Screen to PC Connections Page 15

17 Computer Touch screen Description HDMI Output HDMI input Computer drives the video display on the monitor Touch Input (USB) Touch Output (USB) Feedback from the touch monitor to the PC on where has been touched on the screen Power the touch screen ON from the mains by using the power lead included. Then plug the PC into the internal mains power extension and power ON. Connect the screen to the PC via the HDMI cable and USB Cable (as shown above). Before taking any more steps ensure that the screen is sourcing its display from the PC. This is done by first pressing MODE and then scrolling down to the desired input source (HDMI) and select by pressing PLAY. PC-RGB PC-RGB (BNC) COMPONENT DVI HDMI AV1 AV2 DMP IMPORTANT: If the Touch Screen is the only monitor connected to your PC DO NOT take the following step. Only proceed with the following if you are using a laptop or another monitor is connected to your PC. Access the display options from your Control Panel or right-click on your Desktop and choose Properties (then Settings ) or Screen resolution. Page 16

18 You should now click Detect to allow the PC to discover the Touch Screen display then Identify to establish which display is the touch screen. Select the display that corresponds with the Touch Screen display then check the box Make this my main display or Use this devise as the primary monitor. This will make the Touch Screen display your main monitor. Page 17

19 3. F.A.Qs and Troubleshooting Guide 3.1 My Touch Screen is not displaying what is on my PC Input Source Your Touch Screen may be sourcing its display from another input. First, pointing your remote at the silver control box, press MODE and then scroll down to the desired input source and select by pressing PLAY. PC-RGB PC-RGB (BNC) COMPONENT DVI HDMI AV1 AV2 DMP Display/monitor button on keyboard Your keyboard may have a display/monitor button on it, especially if you are using a laptop. If your Touch Screen does not display the content of the PC try hitting this button before contacting your supplier. 3.2 My display turns itself OFF when it s not connected to my PC Power saving function If your Touch Screen display is powered ON without being connected to a PC via a visual signal (e.g. VGA, DVI etc.) it will automatically power OFF within a few minutes. If your Touch Screen display is Page 18

20 not being supplied with a video signal it will power OFF so ensure that video signal connection is connected properly. Also you must ensure that the Touch Screen is accessing the correct input. Press MODE and then scroll down to the desired input source and select by pressing PLAY. PC-RGB PC-RGB (BNC) COMPONENT DVI HDMI AV1 AV2 DMP 3.3 My screen is displaying video signal but touch function is disabled Please ensure the Touch Screen is connected to the PC via the USB Cable. Go through the steps in Section 2.2 to do this correctly. 3.4 My Remote control is not working If you have unpacked your unit, powered it ON and the remote control does not seem to be working please point the remote control at the silver control box inside the locker door. The Serial Control Box has the remote s infrared sensor in it and must be used when operating the Remote control. Page 19

21 Page 20