aorun manual V1.0 OCTOBER 2017

Transcription

1 aorun manual V1.0 OCTOBER 2017

2 table of CONTENTS Dimensions 2 Safety information 5 Specifications 7 Included items 8 Physical installation 9 Control panel 11 Operating instructions 12 Channel function 15 Circuit connection diagram 18 Cleaning and maintanances 19 Troubleshooting 19

3 b0 i0 c0 p2; Dimensions All dimensions are in millimeters ±

4 Safety Information WARNING! Read the safety precautions in this section before installing, powering, operating or servicing this product The following symbols are used to identify important safety information on the product and in this manual: DANGER! Safety hazard. Risk of severe injury or death. DANGER! Hazardous voltage. Risk of lethal or severe electric shock. WARNING! Fire hazard. WARNING! LED light emission. Risk of eye injury. WARNING! Burn hazard. Hot surface. Do not touch. WARNING! Wear protective eyewear. WARNING! Refer to user manual. INSTALLATION Make sure all (mounting) parts of the fixture are in a good state. Make sure the point of attachment is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework. So that if the primary support system fails, the fitting falls as little as possible. If the safety chain gets worn out, it needs to be replaced. MINIMUM DISTANCE OF ILLUMINATED OBJECTS The projector must be positioned so that the objects within the reach of the beam are at least 12 metres from the lens of the projector. MINIMUM DISTANCE FROM FLAMMABLE MATERIALS The projector must be positioned so that any flammable materials are at a distance of at least 0.2 metres from every point on the surface of the fitting. MOUNTING SURFACES We advise to mount the fitting on normally unflammable surfaces. MAXIMUM AMBIENT TEMPERATURE Stop using the fixture when the ambient temperature (Ta) exceeds 40 C. 3.0

5 Safety Information Protection against electrical shock The connection must be made with a RNING! power supply system including efficient earthing (Class e safety I appliance precautions according in to standard this section EN ). before It is important to protect ng, powering, the supply lines operating of the projectors or servicing from indirect this contact and/or shorting to earth by using roduct appropriately sized residual current devices. Connection to main supply Connection to the electricity main supply must be carried out by a qualified electrical installer. Check if the main frequency and voltage correspondswith the values of the projector as described on the electrical data label. This label also provides you about the maximum number of fixtures to connect to the main supply in order to avoid overloading. Don't use the power cable when the insulation is damaged. The damaged cable must be repaired by the manufacturer or the distributor in order to avoid any dangerous situations. Temperature of the external surface The maximum temperature that can be reached on the external surface of the fixture, in a thermally steady state, is 100 C. Maintenance Before starting any maintenance or cleaning work on the fixture, cut off the power from the main power supply. After switching off the power, do not remove any parts of the fixture, for at least 30 minutes to avoid any burns. After 30 minutes change that the lamp will explode nil. The fixture is designed to hold any splinters when the lamp explodes. The lenses must be mounted properly, and when damaged, the lenses must be replaced with proper spare parts. 4.0

6 Safety Information Lamp The fixture mounts a high-pressure lamp RNING! that needs an external igniter build in which is fitted e safety onto the precaut device. Carefully ons in read this the section before "operating instructions" ng, powering, provided by the operating lamp manufacturer or servi and ing this immediately replace the lamp when roduct damaged or deformed by heat. Battery This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. The products referred to in this manual conform to the European Community Directives to which they are subject: Low Voltage 2014/35/EU Electromagnetic Compatibility 2014/30/EU 5.0

7 specifications Lamp: Brand: OSRAM SIRIUS HRI 330W XL Power: 450W Colour temperature: 7500K Average life: ±1500h Motors: 12 Ultra quiet motors Input: DMX 512, RDM Color: 14 colors & open Software upgrade: Software upgrade via USB Features: Remote control lamp switch function, display light, lamp using time, automatically adjust cooling-fan s speed. Cooling: Forced ventilation with axial fans. Housing: Heatproof plastic & module pressing alloy materials. Gobo: Open, 11 Gobo & 3 animation range Strobe: Double lens strobe (0,5-9 times / second) CE: In conformity with the European Union Low Voltage. Directive 2014/35/EU and Electromagnetic compatibility Directive 2014/30/EU. Dimmer: 0-100% linear adjustment Prism: 8 facet prism, 16 facet double prism & fast switching Transport & maintenance: Two side handles for transportation The fixture has a tilt lock for transportation and maintenance. Focus and lens: High precision optical focus frost Wash effect: Adjustable frost effects Address set: Automatic charging battery, DMX address could be set without electricity. 6.0

8 AORUN PHOTOMETRICS 7.0

9 Model Lamp power Light power Voltage / frequency Netto weight Size Box size Gross weight Channel CLF Aorun 330W 450W AC100V - 240V - 50/60Hz 18,8kg 380x280x529mm 400x345x570mm 21,2kg 14 / 16CH X / Y travel 540 / 250 X / Y resolution 2,11 / 0,98 X / Y speed 2,7S / 1,6S Motor 12 Beam angle 0-2,3 Color Gobo Prism 14 colors & white 11 gobo s, 1 white & 3 animation range 8 facet prisms, 16 facet double prims & prism combination macro s Included items in/out 8.0

10 aorun physical installation aorun Installing the fixture - Fig. 3 The fixture can be installed on the floor resting on a special rubber feet or on a truss. Installing the fixture - Fig. 3 The fixture can be installed on the floor resting on a special rubber feet or on a truss. WARNING: When the fixture is positioned on truss, the safety rope must be fitted. This must be securely fixed to the support structure of the fixture and then connected to the fixing point at the centre of the base. WARNING: When the fixture is positioned on truss, the safety rope must be fitted. This must be securely fixed to the support structure of the fixture and then connected to the fixing point at the centre of the base. 9.0

11 in out in power end The N terminal is connected with the blue line. N Ground L The L terminal is connected with the brown line. Not more then 4 fixtures could be in a serie. Connection to the mains must be carried out by a qualified electrical installer. After connecting the units to a power line, press the power mains switch to check if they work normally. 10.0

12 Please use the round 3 or 5-pin XLR plugs & sockets offered by menu facture to connect the first output to the second input and connect the second projector s output to the third projector s input. And in the same way for the rest, eventually connect the last projector s output, all the projectors are together. The projectors s control signal output or input by using the 3 or 5-pin XLR pug and socket. If need to lengthen the communication cable, please make sure the both side of 3 or 5-pin plug is one to one. (one to one, two to two, three to three). Otherwise, the communication cable will be interrupted. The communicate cable is 2-cord screened cable 75 resistance with each core is at least a 0.5mm diameter. (Caution: All the inside leading wire of 3 or 5-pin XLR plug couldn t touch each other. Recommend to use the DMX signal terminator for the installation to avoid the electronic noise damage the digital control signal. The DMX terminator is an XLR connector with a 120 1/2W resistor connected across pin 2 and 3. Which is then plugged into the output socket on the last projector in the chain refer to the connection. control panel AORUN AORUN AORUN AORUN Test Test Test Test

13 operating instructions MAIN MENU MENU I MENU II MENU III DMX address Address: Lamp hours Total: ****(h) Lamp open: ****(h) Temperatuur Board: RDM UID Undistributed Fan 1: 00.0V Fan 2: 00.0V Fan speed / voltage Fan 1: 0000 RPM Fan 2: 0000 RPM Fan3: 0000 RPM 1. Color (***) 2. Shutter (***) 3. Dimmer (***) 4. Gobo (***) 5. Prism (***) Information 6. Prism ROTA (***) 7. Prism Macro (***) DMX live 8. Frost (***) 9. Focus (***) 10. Pan (***) 11. Pan fine (***) 12. Tilt (***) 13. Tilt fine (***) 14. Function (***) 15. Reset (***) 16. Lamp control (***) XY: V*.** System version 10M: V*.** DIS board: V*.** Return (ESC) Channel mode Auto lamp on P/T invert Standard (16CH) Simple (14CH) OFF ON Pan invert Tilt invert OFF ON OFF ON 12.0

14 operating instructions MAIN MENU MENU I MENU II MENU III Language English Backlight Open Auto close (15s) Personal Display Reversal Normal Rota. 180 Backlight blink ON OFF Return (ESC) Return (ESC) 1. Color (***) 2. Shutter (***) 3. Dimmer (***) 4. Gobo (***) 5. Prism (***) 6. Prism ROTA (***) 7. Prism Macro (***) 8. Frost (***) Channel control 9. Focus (***) 10. Pan (***) 11. Pan fine (***) 12. Tilt (***) Manual control 13. Tilt fine (***) 14. Function (***) 15. Reset (***) 16. Lamp control (***) Return (ESC) System reset Reset Pan / tilt reset Head motor reset Test P/T STEP *** Test Test effect STEP *** Test all STEP *** Return (ESC) Return (ESC) Error list Pan Tilt

15 operating instructions MAIN MENU MENU I MENU II MENU III Dimmer Dimmer Focus Focus Color Calibration Stat. gobo Prism Prism Prism rota Service Frost Return (ESC) Default Input: 0000 Time clean Input: 0000 Factory Developer Firmware update Input: 0000 Return (ESC) Return (ESC) Lamp Test Reversal OFF ON English Normal Rota

16 channel function CHANNEL DMX PERCENTAGE FUNCTION COLOR White White + red Red Red + orange Orange Orange + aquamarine Aquamarine Aquamarine + dark green Dark green Dark green + green Green Green + lavender Lavender Lavender + pink Pink Pink + yellow Yellow Yellow + magenta Magenta Magenta + cyan Cyan Cyan + CTO CTO CTO 2 + CTO CTO CTO 1 + CTB CTB CTB + Dark blue Dark blue Dark blue + white CCW, fast --> slow rotation CW, slow --> fast rotation 15.0

17 channel function CHANNEL DMX PERCENTAGE FUNCTION STROBE DIMMER GOBO White Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo Gobo 1 shake slow-fast speed Gobo 2 shake slow-fast speed Gobo 3 shake slow-fast speed Gobo 4 shake slow-fast speed Gobo 5 shake slow-fast speed Gobo 6 shake slow-fast speed Gobo 7 shake slow-fast speed Gobo 8 shake slow-fast speed Gobo 9 shake slow-fast speed Gobo 10 shake slow-fast speed Gobo 11 shake slow-fast speed Gobo 12 shake slow-fast speed Gobo 13 shake slow-fast speed Gobo 14 shake slow-fast speed 16.0

18 CHANNEL DMX PERCENTAGE FUNCTION PRISM Unused range Prism Prism Prism 1 + prism 2 PRISM ROTATION 0 0 Unused range CCW, fast --> slow CW, slow --> fast Slow --> fast rotation, 90 back and forth Slow --> fast rotation, 180 back and forth Slow --> fast rotation, 270 back and forth Slow --> fast rotation, 360 back and forth PRISM MACRO FROST FOCUS PAN PAN FINE TILT TILT FINE FUNCTION Unused range Effects reset Pan/tilt reset Complete reset Unused range Lamp OFF Unused range Lamp ON 17.0

19 circuit connection diagram 18.0

20 cleaning and maintenances To ensure that the fixture works normally, always keep it clean. We recommend to clean the fans and ventilation inlet frequently. The lens and dichroic color filters should also be cleaned regularly to maintain an optimum light output. Do not use any type of solvent on the dichroic color filters, it will damage the fixture. Disconnect the power supply when you start maintenace or take down the light. Please let the fixture cool down for at least 10 minutes. If you need to replace the lamp, please wait for at least 30 minutes to let the lamp cool down completely to prevent burn injuries. Please inspect the lens or other moving parts regularly and keep them clear and static. If you find anything damaged or loose, you must change the fixture or repair the fixture in order to avoid accidents. The light uses a strong cooling system. It is easy for the dirty to be collected. Please clear the fan inlet frequently. After you use the light, please check the intake place whether there is any material, please clean it up, or the fan will not work properly and will cause damage. troubleshooting It is recommended to check below trouble shooting. Any unsolutioned problems should always be handle by the professional person. Disconnect the power supply before maintenance the light. Lamp off Please check if the correct lamp is installed. Please check the connection of the power supply or switch is ok. Please check whether the lamp will be at the end of his life, please replace with the same lamp. Please check if the power supply is between 100 and 240 VAC. Please check the connection of the trigger circuit inside the base has a loose contact. 19.0

21 Check menu information fan speed / voltage fan1, fan2 & fan3 for fanspeed. Whether the fan speed is 500RPM above, below 500RPM the lamp does not turn on, replace with the same fan. Please check if the temperature switch is damaged. Enter the menu information then select temperature to see whether the temperature display boad is too high or has no temperature information. The light beam is dark, not inhomogeneous When the lamp is to the usage life,the light is not enough, please change a new one with the same specifications. Please check the reflector parts are dirty. Keep them clear. Please measure if the power supply is between 100 and 240 VAC. Enter the menu service options to choose calibration to enter the Color and Gobo calibration. The light shadow is fogging Please check the electric focus inside. Please check the focus and lens for dirt. After cleaning, please add some temperature durable juice on the moving parts. The light works interruptly Please check if the fan works normally. Please check whether fan covers are clean. Please check if the lamp is not at the end of the usage time. Please check if the power supply is between 100 and 240 VAC and if the connection of the power supply or the circuit are good. Please check if the temperature switch is good. 20.0

22 aorun CLFLIGHTING