4K/UHD HDMI Over 100M HDBaseT TX/RX with Ethernet, Control, PoE, and Optical Audio

Transcription

1 4K/UHD HDMI Over 100M HDBaseT TX/X with Ethernet, Control, PoE, and Optical Audio ATUHDEX100CEAKIT User Manual Please check com/atuhdex100ceakit for the most recent firmware update or manual

2 Table of Contents 1. Introduction.... Package Contents.... Features Before You Start Category Cable Panel Descriptions a. Front Panel... 5 b. ear Panel Captive Screw Connectors Connection Diagram Specifications Safety Information Warranty Atlona Product egistration... 14

3 Introduction Pass through support of 4K (UHD), 560x048, I,, bidirectional Ethernet, and lossy/lossless audio signals up to 8ft (100m). The 100CEA extenders provide an affordable, high quality, solution for your audio and video needs. Package Contents 1 x ATUHDEX100CEATX 1 x ATUHDEX100CEAX 1 x 48V DC power supply x Female captive screw connector pin (x1): power, 5 pin (x1): /I, and 6 pin (x1): I/) x Pair of wall/table mount ears x Pair of screws for wall/mount ears 1 x I emitter (ATICSTX) 1 x User manual Features Extends I,, Ethernet, and audio/visual content up to 8ft over a single category cable Optical Audio ports, for routing audio from the zone back to an AV or zone amplifier Supports resolutions up to 4K (UHD) chroma subsampling 4::0 8bit I ports for use with I remote controls and rd party I controllers Bidirectional Ethernet pass through Provides PoE (Power over Ethernet) Multichannel audio pass through up to Dolby TrueHD, DTSHD Master Audio, Dolby Atmos, and DTS:X Full D pass through HDCP. compliant Field updatable firmware Before You Start When installing the extenders DO T: Cover the vents Install into a sealed wall Install into an area without adequate air ventilation Connect the screws to these four holes when mounting to a wall. Do not cover venting! Connect the screws to these four holes when mounting to a table. *emove the side screws from the case and use for bracket installation

4 Category Cable For the category cables used in the installation of these products, please be sure to use a 568B termination as pictured below: 1. White Orange. Orange. White Green 4. Blue 5. White Blue 6. Green 7. White Brown 8. Brown Use the table below to verify the best category cable for the installation. Performance ating Type of cable Wiring Shielding CAT5e/6 CAT6a/7 Solid Shielded (STP/FTP) *** **** Stranded Patch cable (Not recommended) Termination Unshielded (UTP) ** N/A Unshielded (UTP) * N/A Shielded (STP/FTP) * N/A Please use EIA/TIA568B termination Important! 4K (UHD) signals are sensitive to cable quality and installation technique. It is recommended to use CAT6a/7 solid core cables for best results. Note: For cable distances see the specifications on page 11 Connector Connector type and size is very important to ensure extenders work correctly. Please use the matching cable type with the correct J45 connector. CAT5e cables should use only CAT5e J45 connectors CAT6 cables should use only CAT6 connectors CAT6a cables should use only CAT6a connectors CAT7 cables should use only CAT7 connectors Using the wrong size connectors may result in interference causing loss of signal. Important! EZ J45 connectors are not recommended with HDBaseT extenders. Doing so may result in interference with audio and video transmission. 4

5 Panel Description TX 1 ATUHDEX100CEATX + OUT I DC 48V OPTICAL X TX TX X HDBaseT OUT HDMI IN Firmware Use a MiniB USB to USB A cable to connect to a Windows computers for updating. Yellow Link LED: Signal indicator for the HDBaseT OUT port Solid Good signal from the HDBaseT port Blinking Category cable is disconnected or not receiving signals No Light No signal is being received from the HDBaseT port Green Power LED: Power indicator Solid Plugged in and receiving power Blinking Power is intermittent or there is a problem with the cable No Light No power is passing from the wall outlet to the transmitter (check the cable or outlet). DC 48V Connect included captive screw power adapter here 4. Optical Connect to an AV or zone amplifier 5. Bidirectional, send signal to or from a control system, PC, source, or display I Connect I emitter (included) or rd party control box to this port 6. HDBaseT OUT Connect a category cable from here to an ATUHDEX100CEAX (included in KIT) 7. HDMI IN Connect HDMI or DVI (with adapter) source here E.g. Media player, cable box, HDDA series, HH series, UHDHH series, UHDSW series, etc 8. Connect to a router to for Ethernet and TCP/IP pass through 5

6 X 1 ATUHDEX100CEAX IN I OPTICAL X TX TX X P HDBaseT IN HDMI OUT Firmware Use a MiniB USB to USB A cable to connect to a Windows computers for updating. Yellow Link LED: Signal indicator for the HDBaseT IN port Solid Good signal from the HDBaseT port Blinking HDBaseT signal is intermittent No Light No signal is being received from the HDBaseT port Green Power LED: Power indicator Solid Plugged in and receiving power Blinking Power is intermittent or there is a problem with the cable No Light No power is passing from the transmitter to the receiver Note: Check the category cable or the AC outlet for the transmitter. Optical Connect audio from display loop out or local source 4. Bidirectional, send signal to or from a control system, PC, source, or display I Connect I emitter (included) or receiver (ATICSX sold separately) to this port 5. HDBaseT IN Connect a category cable from here to an ATUHDEX100CEATX (included in KIT) or HDBaseT matrix 6. HDMI OUT Connect HDMI or DVI (with adapter) display here 7. Connect to a display to send Ethernet or TCP/IP signals 6

7 Captive Screw Captive screw connectors are an added feature on the UHD extender. The captive screw connectors allow you to cut cables down to a suitable length, reduce cable clutter, while providing a more reliable connection. Connecting When connecting the cables to the female captive screw connector it is important that the wires be terminated correctly. The female captive screw connector has a contact plate at the top and must have the wires touching it for signal to pass. When wired correctly (see picture A) the signal will pass, incorrectly (see picture B) no signal will pass. A B The captive screw connectors have a contact bar that is adjusted to compress the wire against the top contact plate. Use the screws at the top of the connector to compress the wire against the contact plate. Clockwise Turn the screws clockwise to raise the contact bar to the upper contact plate and hold the wires in place. Counter Clockwise Turn the screws counter clockwise to lower the contact bar to release the wires. 1 Female captive screw connectors are included: Power (see picture 1) and & I (see picture ). Power I 4 + The power cable (picture 4) will have exposed wires. Each wire is encased in a different colored cover. 5 Black: White: + Pin out color will differ per cable. pin out will be determined by the cable and will connect as x (receiver), Tx (transmitter), and (ground). (See picture 5) Note: The I receiver is optional for the UHDEX100CEAKIT. The compatible I receiver (ATICSX) can be purchased through. The wires of the emitter and receiver have been marked to differentiate the pin outs. Signal (TX) Ground ( ) The included I emitter has two wires: signal and ground. Signal will have a solid line and ground will be blank. The I emitter will plug into the I OUT ports. Signal (X) Ground ( ) Power (P) There are three wires on the I receiver (ATICSX sold separately): signal, ground, and power. Signal has a dotted line, ground will be blank, and power will have a solid line. The I receiver will plug into the I IN port of the ATUHDEX100CEAX. 7

8 ZIGBEE 1V DC FACTOY ESTOE ID 1 I OUT SEIAL 1 SEIAL HDMI VIDEO OUT PONENT WIFI 1 DIGITAL esata ETHENET USB COAX OUT L AUDIO OUT AUDIO IN 1 4 ELAYS WIFI CONTACTS Connection Diagram (Matrix switcher) Set top box Video HDBaseT Control Ethernet Bluray player Me dia 1 ENTE 4 5 ATUHDPO44M F CAEL EDID INFO ON 1 4 1ED 4 5 X TX + L 1 L L I IN HDMI IN ZONE OUT AUDIO OUT S S I IN S S S S S S I OUT OFF PW: 10040VAC 50/60Hz Control System ATUHDEX100CEATX + OUT DC 48V OPTICAL X TX TX I X HDBaseT OUT HDMI IN.4 5 i 1 4 OUTE outer ATUHDEX100CEAX IN I OPTICAL X TX TX X P HDBaseT IN HDMI OUT Game Console Game console 8

9 GAIN GAIN GAIN GAIN GAIN GAIN SPEAKE SPEAKE SPEAKE SPEAKE SPEAKE SPEAKE ZIGBEE 1V DC FACTOY ESTOE ID 1 I OUT SEIAL 1 SEIAL HDMI VIDEO OUT PONENT WIFI 1 DIGITAL esata ETHENET USB COAX OUT L AUDIO OUT AUDIO IN 1 4 ELAYS WIFI CONTACTS Connection Diagram (HDMI Matrix) Set top box I IN X TX S HDMI IN ATUHDHH88M HDMI Matrix Switcher HDMI OUT DC 1V ATUHDEX100CEATX + OUT I Control System DC 48V OPTICAL X TX TX X HDBaseT OUT HDMI IN ATUHDEX100CEAX IN I OPTICAL X TX TX X P HDBaseT IN HDMI OUT Me dia 9

10 ZIGBEE 1V DC FACTOY ESTOE ID 1 I OUT SEIAL 1 SEIAL HDMI VIDEO OUT PONENT WIFI 1 DIGITAL COAX OUT AUDIO OUT L AUDIO IN esata ETHENET 1 4 ELAYS WIFI CONTACTS Connection Diagram (Switcher) Media Player Set top box Video HDBaseT Control Audio Me dia Bluray player L AUDIO + + S/PDIF OUT X TX HDMI IN HDMI OUT DC 5V OUTE.4 5 i 1 4 outer ATUHDEX100CEATX + OUT I DC 48V OPTICAL X TX TX X HDBaseT OUT HDMI IN ATUHDEX100CEAX IN I OPTICAL X TX TX X P HDBaseT IN HDMI OUT Game Console 10

11 Specifications Video esolutions Video (UHD), 048x1080p, 576p, 576i, 480p, 480i VESA 560x048, 560x1600, 048x156, 190x100, 1680x1050, 1600x100, 1600x900, 1440x900, 1400x1050, 166x768, 160x768, 180x104, 180x800, 180x768, 115x768, 104x768, 800x600, 640x480 Colorspace YCbCr, GB Chroma Subsampling 4:4:4, 4::, 4::0 Color Depth 8bit, 10bit, 1bit Audio HDMI pass through PCM Ch, LPCM 5.1, LPCM 7.1, Dolby Digital, DTS 5.1, Dolby Digital Plus, Dolby TrueHD, DTSHD Master Audio, Dolby Atmos Optical pass through PCM Ch, LPCM 5.1, Dolby Digital, DTS 5.1 Sample ate khz, 44.1kHz, 48kHz, 88.kHz, 96kHz, 176.4kHz, 19kHz Bit ate up to 64bit Distance 4K up to 70M up to 0 ft 4K up to 100M up to 8 ft 1080p up to 100M up to 8 ft HDMI 4K up to 5M up to 15 ft HDMI 1080p up to 10M up to 0 ft Signal Bandwidth 10. Gbps CEC Yes HDCP supports up to. Temperature Operating 0 C to 50 C F to 1 F Storage 40 C to 70 C 40 F to 158 F Humidity 0 to 90% noncondensing Power Consumption Supply 0.61W (when TX and X are paired) Input: AC100~40V 50/60Hz Output: DC48V 0.8A Dimension H x W x D 6 x 146 x 89 (mm) 1.0 x 5.75 x.50 (inch) Weight Device 0.41 kg 0.90 lbs Certification Power Supply Product CE, FCC, culus, ohs, CCC, CM CE, FCC **4096x160@50/60Hz & 840x160@50/60Hz chroma subsampling 4::0 8bit only 11

12 Safety Information Safeguards To reduce the risk of electric shock, do not expose this product to rain or moisture If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket. Do not modify the wall plug. Doing so will void the warranty and safety features. This equipment should be installed near the socket outlet and the device should be easily accessible in the case it requires disconnection. Precautions FCC regulations state that any unauthorized changes or modifications to this equipment, not expressly approved by the manufacturer, could void the user s authority to operate this equipment. Operate this product using only the included external power supply. Use of other power supplies could impair performance, damage the product, or cause fires. In the event of an electrostatic discharge this device may automatically turn off. If this occurs, unplug the device and plug it back in. Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them. Be especially careful of plugins or cord exit points from this product. Avoid excessive humidity, sudden temperature changes or temperature extremes. Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements, fish tanks, and swimming pools. Use only accessories recommended by Atlona to avoid fire, shock, or other hazards. Unplug the product before cleaning. Use a damp cloth for cleaning and not cleaning fluid or aerosols. Such products could enter the unit and cause damage, fire, or electric shock. Some substances may also mar the finish of the product. Never open, remove unit panels, or make any adjustments not described in this manual. Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage to your product. Opening the product will void the warranty. Do not attempt to service the unit. Disconnect the product and contact your authorized Atlona reseller or contact Atlona directly. 1

13 Atlona, Inc. ( Atlona ) Limited Product Warranty Policy Coverage Atlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service. Under its Limited Product Warranty, Atlona, at its sole discretion, will either: A) repair or facilitate the repair of defective products within a reasonable period of time, restore products to their proper operating condition and return defective products free of any charge for necessary parts, labor and shipping O B) replace and return, free of charge, any defective products with direct replacement or with similar products deemed by Atlona to perform substantially the same function as the original products O C) refund the prorated value based on the remaining term of the warranty period, not to exceed MSP, in cases where products are beyond repair and/or no direct or substantially similar replacement products exist. epair, replacement or refund of Atlona s products is the purchaser s exclusive remedy and Atlona s liability does not extend to any other damages, incidental, consequential or otherwise. This Limited Product Warranty extends to the original enduser purchaser of Atlona s products and is nontransferrable to any subsequent purchaser(s) or owner(s) of these products. Coverage Periods Atlona s Limited Product Warranty Period begins on the date of purchase by the endpurchaser. The date contained on the endpurchaser s sales or delivery receipt is the proof purchase date. Limited Product Warranty Terms New Products 10 years from proof of purchase date for hardware/electronics products purchased on or after June 1, 01 years from proof of purchase date for hardware/electronics products purchased before June 1, 01 Lifetime Limited Product Warranty for all cable products Limited Product Warranty Terms efurbished (BStock) Products years from proof of purchase date for all efurbished (BStock) hardware and electronic products purchased on or after June 1, 01 emedy Atlona recommends that endpurchasers contact their authorized Atlona dealer or reseller from whom they purchased their products. Atlona can also be contacted directly. Visit www. for Atlona s contact information and hours of operation. Atlona requires that a dated sales or delivery receipt from an authorized dealer, reseller or endpurchaser is provided before Atlona extends its warranty services. Additionally, a return merchandise authorization (MA) and/or case number, is required to be obtained from Atlona in advance of returns. Atlona requires that products returned are properly packed, preferably in the original carton, for shipping. Cartons not bearing a return authorization or case number will be refused. Atlona, at its sole discretion, reserves the right to reject any products received without advanced authorization. Authorizations can be requested by calling (US toll free) or (US/international) or via Atlona s website at Exclusions This Limited Product Warranty excludes: Damage, deterioration or malfunction caused by any alteration, modification, improper use, neglect, improper packing or shipping (such claims must be presented to the carrier), lightning, power surges, or other acts of nature. Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product. Equipment enclosures, cables, power supplies, batteries, LCD displays, and any accessories used in conjunction with the product(s). Products purchased from unauthorized distributors, dealers, resellers, auction websites and similar unauthorized channels of distribution. 1

14 Disclaimers This Limited Product Warranty does not imply that the electronic components contained within Atlona s products will not become obsolete nor does it imply Atlona products or their electronic components will remain compatible with any other current product, technology or any future products or technologies in which Atlona s products may be used in conjunction with. Atlona, at its sole discretion, reserves the right not to extend its warranty offering in instances arising outside its normal course of business including, but not limited to, damage inflicted to its products from acts of god. Limitation on Liability The maximum liability of Atlona under this limited product warranty shall not exceed the original Atlona MSP for its products. To the maximum extent permitted by law, Atlona is not responsible for the direct, special, incidental or consequential damages resulting from any breach of warranty or condition, or under any other legal theory. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you. Exclusive emedy To the maximum extent permitted by law, this limited product warranty and the remedies set forth above are exclusive and in lieu of all other warranties, remedies and conditions, whether oral or written, express or implied. To the maximum extent permitted by law, Atlona specifically disclaims all implied warranties, including, without limitation, warranties of merchantability and fitness for a particular purpose. If Atlona cannot lawfully disclaim or exclude implied warranties under applicable law, then all implied warranties covering its products including warranties of merchantability and fitness for a particular purpose, shall provide to its products under applicable law. If any product to which this limited warranty applies is a Consumer Product under the MagnusonMoss Warranty Act (15 U.S.C.A. 01, ET SEQ.) or other applicable law, the foregoing disclaimer of implied warranties shall not apply, and all implied warranties on its products, including warranties of merchantability and fitness for the particular purpose, shall apply as provided under applicable law. Other Conditions Atlona s Limited Product Warranty offering gives legal rights, and other rights may apply and vary from country to country or state to state. This limited warranty is void if (i) the label bearing the serial number of products have been removed or defaced, (ii) products are not purchased from an authorized Atlona dealer or reseller. A comprehensive list of Atlona s authorized distributors, dealers and resellers can be found at Atlona, Inc Product egistration Thank you for purchasing this Atlona product. We hope you enjoy it and will take an extra few moments to register your new purchase. egistration creates an ownership record if your product is lost or stolen and helps ensure you ll receive notification of performance issues and firmware updates. At Atlona we respect and protect your privacy, assuring you that your registration information is completely secure. Atlona product registration is completely voluntary and failure to register will not diminish your limited warranty rights. To register go to: 14