MSP430-HG2231 development board Users Manual
|
|
- Maurice Lindsey
- 6 years ago
- Views:
Transcription
1 MSP0-HG development board Users Manual All boards produced by Olimex are ROHS compliant Revision Initial, June 0 Copyright(c) 0, OLIMEX Ltd, All rights reserved Page
2 INTRODUCTION: MSP0-HG is header board with MSP0GIPWR ultralowpower mixed signal microcontroller from Texas Instruments. MSP0GIPWR has a built-in -bit timer, ten I/O pins, a 0-bit A/D converter and built-in communication capability using synchronous protocols (SPI or IC). On the board are available JTAG connector, one status led and extension headers for each microcontroller pin, where you can connect your own circuits. All this allows you to build a diversity of applications. BOARD FEATURES: Microcontroller MSP0GIPWR JTAG interface Status led Extension headers for each microcontroller pin FR-,. mm, soldermask, component print Dimensions:.00 x 0.00 mm (.0 x 0.9") ELECTROSTATIC WARNING: The MSP0-HG board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. BOARD USE REQUIREMENTS: Cables: The cable you will need depends on the programmer/debugger you use. If you use MSP0-JTAG-TINY, MSP0-JTAG-TINY-V or MSP0JTAG-ISO, you will need USB A-B cable. If you use MSP0-JTAG, you will need LPT cable. Hardware: Programmer/Debugger MSP0-JTAG, MSP0-JTAG-TINY, MSP0-JTAG-TINY-V, MSP0-JTAG-ISO by OLIMEX, or other compatible programming/debugging tool. Page
3 PROCESSOR FEATURES: MSP0-HG board use MSP0GIPWR microcontroller from Texas Instruments with these features: Low Supply-Voltage Range:. V to. V Ultra-Low Power Consumption Active Mode: 0 μa at MHz,. V Standby Mode: 0. μa Off Mode (RAM Retention): 0. μa Five Power-Saving Modes Ultra-Fast Wake-Up From Standby Mode in Less Than μs -Bit RISC Architecture,.-ns Instruction Cycle Time Basic Clock Module Configurations Internal Frequencies up to MHz With One Calibrated Frequency Internal Very Low Power Low-Frequency (LF) Oscillator -khz Crystal External Digital Clock Source -Bit Timer_A With Two Capture/Compare Registers Universal Serial Interface (USI) Supporting SPI and IC Brownout Detector 0-Bit 00-ksps A/D Converter With Internal Reference, Sample-and-Hold, and Autoscan Serial Onboard Programming, No External Programming Voltage Needed, Programmable Code Protection by Security Fuse On-Chip Emulation Logic With Spy-Bi-Wire Interface For more information about this microcontroller, see here. Page
4 BLOCK DIAGRAM: Page
5 Page EXT HNx uf C POWER HNx(OPEN).V P. P. P. P. P. P. P. VIN EXT HNx k R P_OUT.V.V P_IN VIN TEST RST P.0 P. P. 0 NA C 9 R K.V MCP0-0E/MB GND VOUT VIN VR(.V) HNx JTAG uf C.V 0 9 MSP0GIPWR P. P. C P. C Q. khz/pf GND P. 00n C.V 0pF 0pF COPYRIGHT(C) 0, OLIMEX Ltd. Rev. A MSP0-HG TEST/SBWTCK DVCC RST/NMI/SBWTDIO P.0/TA0CLK/ACLK P./TA0.0 P./TA0. P. DVSS P./SMCLK/TCK XIN/P./TA0. P./TA0.0/SCLK/TMS XOUT/P. P./TA0./SDO/SCL/TDI/TCLK P./SDI/SDA/TDO/TDI U 90R R LED red P.0 SCHEMATIC:
6 BOARD LAYOUT: POWER SUPPLY CIRCUIT: MSP0-HG can take power form: EXT pin (VIN) and pin (GND) from to VDC not typical POWER connector (the connector looks like opened jumper) from to VDC JTAG The programmed board power consumption is about 0 ma with all peripherals enabled. RESET CIRCUIT: MSP0-HG reset circuit includes MSP0GIPWR pin 0 (RST/NMI/SBWTDIO), JTAG connector pin, and R (kω). CLOCK CIRCUIT: Quartz crystal. khz is connected to MSP0GIPWR pin (XOUT/P.) and pin (XIN/P./TA0.). Page
7 JUMPER DESCRIPTION: P_IN P_OUT When this jumper is closed, the board is power supplied by the standard JTAG pin. This is only possible when the consumption of the board is not very high which is typically the case with MSP0 microcontrollers. If this jumper is open the board should be power supplied by another external source. This jumper and P_OUT should always be reversely open/closed, i.e. if P_IN is closed, P_OUT should be open and vice versa. Default state is closed. When this jumper is closed, the board is power supplied not by the JTAG but from external source. Then the JTAG has to synchronize with the working voltages which is done through this line. This is especially important when debugging with JTAG. This jumper and P_IN should always be reversely open/closed, i.e. if P_OUT is closed, P_IN should be open and vice versa. Default state is opened. INPUT/OUTPUT: Status led (red) with name LED, connected to MSP0GIPWR pin (P.0/TA0CLK/ACLK). Page
8 EXTERNAL CONNECTORS DESCRIPTION: JTAG: P. Via P_IN to.v P. Via P_OUT to.v P. NC P. TEST 9 GND 0 NC RST NC NC NC EXT: VCC P. P. P.0 RST TEST GND VIN EXT: Page
9 GND P. P. P. P. P. P. P. POWER: GND VIN Page 9
10 MECHANICAL DIMENSIONS: Page 0
11 AVAILABLE DEMO SOFTWARE: msp0hg_demo demonstrates blinking led Page
12 ORDER CODE: MSP0-HG - assembled and tested board How to order? You can order to us directly or by any of our distributors. Check our web for more info. Revision history: Board's revision Rev. A, March 0 Manual's revision Rev. Initial, June 0 Page
13 Disclaimer: 0 Olimex Ltd. All rights reserved. Olimex, logo and combinations thereof, are registered trademarks of Olimex Ltd. Other terms and product names may be trademarks of others. The information in this document is provided in connection with Olimex products. No license, express or implied or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Olimex products. Neither the whole nor any part of the information contained in or the product described in this document may be adapted or reproduced in any material from except with the prior written permission of the copyright holder. The product described in this document is subject to continuous development and improvements. All particulars of the product and its use contained in this document are given by OLIMEX in good faith. However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product. Page
MSP430-H2618 development board Users Manual
MSP430-H2618 development board Users Manual All boards produced by Olimex are RoHS compliant Rev. Initial, April 2009 Copyright(c) 2009, OLIMEX Ltd, All rights reserved Page 1 INTRODUCTION: MSP430-H2618
More informationMSP430-CCRFLCD development board Users Manual
MSP430-CCRFLCD development board Users Manual All boards produced by Olimex are ROHS compliant Revision A, November 0 Copyright(c) 0, OLIMEX Ltd, All rights reserved Page INTRODUCTION: MSP430-CCRFLCD is
More informationSignalTap Plus System Analyzer
SignalTap Plus System Analyzer June 2000, ver. 1 Data Sheet Features Simultaneous internal programmable logic device (PLD) and external (board-level) logic analysis 32-channel external logic analyzer 166
More informationRF4432 wireless transceiver module
RF4432 wireless transceiver module 1. Description RF4432 adopts Silicon Lab Si4432 RF chip, which is a highly integrated wireless ISM band transceiver. The features of high sensitivity (-121 dbm), +20
More informationSTEVAL-ICB004V1. Advanced resistive touchscreen controller demonstration board based on the STMPE811. Features. Description
Advanced resistive touchscreen controller demonstration board based on the STMPE811 Data brief Features Four-wire resistive touch-sensing demonstration GUI Configurable touch-sensing parameters STMPE811
More informationComparing JTAG, SPI, and I2C
Comparing JTAG, SPI, and I2C Application by Russell Hanabusa 1. Introduction This paper discusses three popular serial buses: JTAG, SPI, and I2C. A typical electronic product today will have one or more
More informationuresearch GRAVITECH.US GRAVITECH GROUP Copyright 2007 MicroResearch GRAVITECH GROUP
GRAVITECH.US uresearch GRAVITECH GROUP Description The I2C-7SEG board is a 5-pin CMOS device that provides 4-digit of 7-segment display using I 2 C bus. There are no external components required. Only
More informationDMC550 Technical Reference
DMC550 Technical Reference 2002 DSP Development Systems DMC550 Technical Reference 504815-0001 Rev. B September 2002 SPECTRUM DIGITAL, INC. 12502 Exchange Drive, Suite 440 Stafford, TX. 77477 Tel: 281.494.4505
More informationSKY LF: GHz 4x2 Switch Matrix with Tone/Voltage Decoder
DATA SHEET SKY13292-365LF: 0.25-2.15 GHz 4x2 Switch Matrix with Tone/Voltage Decoder Applications VDD P0 B1 B2 DBS switching systems cable TV/modems Features Control Circuit Broadband frequency range:
More informationRF4432F27 wireless transceiver module
RF4432F27 wireless transceiver module 1. Description RF4432F27 is 500mW RF module embedded with amplifier and LNA circuit. High quality of component, tightened inspection and long term test make this module
More informationSAU510-USB ISO PLUS v.2 JTAG Emulator. User s Guide 2013.
User s Guide 2013. Revision 1.00 JUL 2013 Contents Contents...2 1. Introduction to...4 1.1 Overview of...4 1.2 Key Features of...4 1.3 Key Items of...5 2. Plugging...6 2.1. Equipment required...6 2.2.
More informationSTA2051E VESPUCCI 32-BIT SINGLE CHIP BASEBAND CONTROLLER FOR GPS AND TELEMATIC APPLICATIONS 1 FEATURES. Figure 1. Packages
STA2051 VESPUCCI 32-BIT SINGLE CHIP BASEBAND CONTROLLER FOR GPS AND TELEMATIC APPLICATIONS DATA BRIEF 1 FEATURES ARM7TDMI 16/32 bit RISC CPU based host microcontroller. Complete Embedded Memory System:
More informationMSP430 JTAG / BSL connectors
MSP430 JTAG / BSL connectors (PD010A05 Rev-4: 23-Nov-2007) FAQ: Q: I have a board with the standard TI-JTAG pinhead. Can I use your programmer to flash my MSP430Fxx device? A: Yes. You can use any of our
More informationJTAGcable II In Circuit Emulator for Atmel AVR microcontrollers. User s Guide REV 1.0. Many ideas one solution
JTAGcable II In Circuit Emulator for Atmel AVR microcontrollers REV 1.0 User s Guide Evalu ation Board s for 51, AVR, ST, PIC microcontrollers Sta- rter Kits Embedded Web Serve rs Prototyping Boards Minimodules
More informationProMOS. Bravo1601. Stand-alone BLE SMD Modules. Datasheet (V1.0) ProMOS Co., Ltd. IoT Solutions Provider.
Bravo1601 Stand-alone BLE SMD Modules Datasheet (V1.0) ProMOS Co., Ltd. Description The Bravo1601 series are the compact Bluetooth low energy (BLE) modules, built in TI_CC2640 with the high-performance
More informationCoLinkEx JTAG/SWD adapter USER MANUAL
CoLinkEx JTAG/SWD adapter USER MANUAL rev. A Website: www.bravekit.com Contents Introduction... 3 1. Features of CoLinkEX adapter:... 3 2. Elements of CoLinkEx programmer... 3 2.1. LEDs description....
More informationV6118 EM MICROELECTRONIC - MARIN SA. 2, 4 and 8 Mutiplex LCD Driver
EM MICROELECTRONIC - MARIN SA 2, 4 and 8 Mutiplex LCD Driver Description The is a universal low multiplex LCD driver. The version 2 drives two ways multiplex (two blackplanes) LCD, the version 4, four
More informationLED Array Board.
LED Array Board www.matrixtsl.com EB087 Contents About This Document 2 General Information 3 Board Layout 4 Testing This Product 5 Circuit Description 6 Circuit Diagram 7 About This Document This document
More informationCombo Board.
Combo Board www.matrixtsl.com EB083 Contents About This Document 2 General Information 3 Board Layout 4 Testing This Product 5 Circuit Diagram 6 Liquid Crystal Display 7 Sensors 9 Circuit Diagram 10 About
More informationPCI MPEG Frame Grabber. Model 616. August 6, 2002
SENSORAY CO., INC. PCI MPEG Frame Grabber Model 616 August 6, 2002 Sensoray 2001 7313 SW Tech Center Dr. Tigard, OR 97223 Phone 503.684.8073 Fax 503.684.8164 sales@sensoray.com www.sensoray.com 1. Limited
More informationPART. Maxim Integrated Products 1
9-646; Rev 0; /00 General Description The MAX94 evaluation kit (EV kit) is assembled with a MAX94 and the basic components necessary to evaluate the -bit analog-to-digital converter (ADC). Connectors for
More informationSDA 3302 Family. GHz PLL with I 2 C Bus and Four Chip Addresses
GHz PLL with I 2 C Bus and Four Chip Addresses Preliminary Data Features 1-chip system for MPU control (I 2 C bus) 4 programmable chip addresses Short pull-in time for quick channel switch-over and optimized
More informationAN3075 Application note
Application note Demonstration board user guidelines for the STC3100 battery monitor for gas gauge applications Introduction This application note describes the STEVAL-ISB009V1, a demonstration board specifically
More informationP XGA TFT Monitor. User s Manual
P6151 15 XGA TFT Monitor User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements
More informationSTEVAL-CCM003V1. Graphic panel with ZigBee features based on the STM32 and SPZBE260 module. Features. Description
Graphic panel with ZigBee features based on the STM32 and SPZBE260 module Data brief Features Microsoft FAT16/FAT32 compatible library JPEG decoder algorithm S-Touch -based touch keys for menu navigation
More informationC-MAX. CMM-9301-V3.1S Bluetooth 4.0 Single Mode HCI Module. Description. 1.1 Features
Description This Module is limited to OEM installation ONLY The module is a Bluetooth SIG qualified, miniaturised BLE controller module based on EM Microelectronic's low power fully integrated single-chip
More informationMini Gateway USB for ModFLEX Wireless Networks
Mini Gateway USB for ModFLEX Wireless Networks FEATURES Compatible with all modules in the ModFLEX family. USB device interface & power Small package size: 2.3 x 4.9 External high performance antenna.
More informationAPPLICATION NOTE. Atmel AVR32850: ATSAM4L-EK User Guide. Atmel SAM4L. Features. Introduction
APPLICATION NOTE Atmel AVR32850: ATSAM4L-EK User Guide Atmel SAM4L Features ATSAM4L-EK kit Board description Using the demonstration firmware Introduction The ATSAM4L-EK is a reference design and development
More informationRF1119ATR7. SP4T (Single Pole Four Throw Switch) Product Overview. Key Features. Functional Block Diagram. Applications. Ordering Information
Product Overview The is a single-pole four-throw (SP4T) switch designed for static Antenna/impedance tuning applications which requires very low insertion loss and high power handling capability with a
More informationDLP LightCrafter Display 4710 EVM User s Guide
User's Guide DLP LightCrafter Display 4710 EVM User s Guide This user s guide presents an overview of the DLP LightCrafter Display 4710 evaluation module (EVM) and a general description of the main features
More informationEntry Level Tool II. Reference Manual. System Level Solutions, Inc. (USA) Murphy Avenue San Martin, CA (408) Version : 1.0.
Entry Level Tool II Reference Manual, Inc. (USA) 14100 Murphy Avenue San Martin, CA 95046 (408) 852-0067 http://www.slscorp.com Version : 1.0.3 Date : October 7, 2005 Copyright 2005-2006,, Inc. (SLS) All
More informationApplications. NCO Clock Generator 1. Fine freq. adjustment. Synthesizer 0. Fine freq. adjustment. Synthesizer 1 Fs= Bs 1. *Ks 1. *16*Ms 1.
Features Operates from a single crystal resonator, clock oscillator or voltage controlled oscillator Two independently programmable Numerically Controlled Oscillators (NCOs) generate any clock rate from
More informationLCD Segment Drivers Standard Segment Drivers BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV Rev.A 1/14
LCD Segment Drivers Standard Segment Drivers BU9795AKV,BU9795AFV,BU9795AGUW,BU9794AKV,BU97950FUV No.10044EAT06 Description ROHM standard function segment series achieve UltraLow power consumption. Also
More informationST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32
User manual ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Introduction The ST-LINK/V2 is an in-circuit debugger/programmer for the STM8 and STM32 microcontroller families. The single wire
More informationEmbedded Master Module
September 14, 2011 G H I Comparison Document Embedded Master Module E l e c t r o n i c s GHI Electronics offers various.net Micro Framework hardware solutions that fit a wide range of applications with
More informationDT9834 Series High-Performance Multifunction USB Data Acquisition Modules
DT9834 Series High-Performance Multifunction USB Data Acquisition Modules DT9834 Series High Performance, Multifunction USB DAQ Key Features: Simultaneous subsystem operation on up to 32 analog input channels,
More informationFigure 1: AHK1421 Evaluation Board Pictures.
Introduction EVALUATION BOARD DATA SHEET The AHK evaluation board demonstrates functionality of the AHK and its application as a white LED backlight driver under Skyworks' S Cwire serial digital interface
More informationHD1-LX HDMI & IR Extender
. HD1-LX HDMI & IR Extender Quick Reference & Setup Guide Magenta Research 128 Litchfield Road, New Milford, CT 06776 USA (860) 210-0546 FAX (860) 210-1758 www.magenta-research.com MAGENTA HD1-LX HDMI
More informationM24SR-DISCOVERY. Discovery kit for the M24SR series Dynamic NFC/RFID tag. Features
Discovery kit for the M24SR series Dynamic NFC/RFID tag Data brief Features Ready-to-use printed circuit board (PCB) including: M24SR64-Y Dynamic NFC/RFID tag 31 mm x 30 mm 13.56 MHz double layer inductive
More informationRaspberry Pi debugging with JTAG
Arseny Kurnikov Aalto University December 13, 2013 Outline JTAG JTAG on RPi Linux kernel debugging JTAG Joint Test Action Group is a standard for a generic transport interface for integrated circuits.
More informationModel 6010 Four Channel 20-Bit Audio ADC Data Pack
Model 6010 Four Channel 20-Bit Audio ADC Data Pack Revision 3.1 SW v1.0.0 This data pack provides detailed installation, configuration and operation information for the Model 6010 Four Channel 20-bit Audio
More informationCopyright 2018 Xi an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced, extracted or transmitted in any
Document Version: Document Number: V1.1.0 NS110100423 A8s Receiving Card Copyright 2018 Xi an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced, extracted
More informationAPPLICATION NOTE 4312 Getting Started with DeepCover Secure Microcontroller (MAXQ1850) EV KIT and the CrossWorks Compiler for the MAXQ30
Maxim > Design Support > Technical Documents > Application Notes > Microcontrollers > APP 4312 Keywords: MAXQ1850, MAXQ1103, DS5250, DS5002, microcontroller, secure microcontroller, uc, DES, 3DES, RSA,
More informationObsolete Product(s) - Obsolete Product(s)
Features Camera with ZigBee connectivity based on the STM32 STM32-based camera with ZigBee connectivity Includes microsd card and ZigBee module Works with monitoring unit (order code STEVAL-CCM003V1) Camera
More informationUsing DLP LightCrafter 4500 Triggers to Synchronize Cameras to Patterns
Application Report Using DLP LightCrafter 4500 Triggers to Synchronize Cameras to ABSTRACT This document describes how to use the DLP LightCrafter 4500 with the global trigger function of industrial USB
More informationSTEVAL-IHT005V2. Demonstration board with full 3.3 V ACS/Triac control using the STM32F100. Description. Features
Demonstration board with full 3.3 V ACS/Triac control using the STM32F100 Data brief IEC 61000-4-4 pre-compliance test passed (burst up to 8 kv) IEC 61000-4-5 pre-compliance test passed (surge up to 2
More informationVT5365. Single-chip optical mouse sensor for wireless applications. Features. Applications. Technical specifications. Description.
Single-chip optical mouse sensor for wireless applications Data Brief Features One chip solution with internal micro and minimal external circuitry 1.8V (single battery) or 2.0 V to 3.2 V (serial batteries)
More information4-in-1 Motor Controller CAN
4-in-1 Motor Controller CAN Page 1 of 6 Version 1.10 Technical Data Construction Connector Housing Dimensions Weight Ambient Temperature Protection Class Plastic housing with side flaps 2x Tyco JPT 90
More informationXTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors
XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only
More informationAIFA TECHNOLOGY CORP.
AIFA TECHNOLOGY CORP. WiFi-04 Module Specification Disclaimer and Copyright Notice The contents of this specification are subject to change without notice. Specification contents PROVIDED WITHOUT ANY WARRANTY,
More informationIS01BFRGB LCD SmartDisplay from NKK Switches Low cost implementation featuring the ATtiny13A from Atmel Complete software solution
DKAN0002A Bit-banging the SmartDisplay 09 June 2009 Features IS01BFRGB LCD SmartDisplay from NKK Switches Low cost implementation featuring the ATtiny13A from Atmel Complete software solution Introduction
More informationUsing DLP LightCrafter 4500 Triggers to Synchronize Cameras to
Application Report Using DLP LightCrafter 4500 Triggers to Synchronize Cameras to ABSTRACT This document describes how to use DLP LightCrafter 4500 with the global trigger function of industrial USB 2,
More informationMulti-channel LED driver with integrated boost controller for medium, large LCD panel backlight based on LED7708 and STM32F103C6T6A
Multi-channel LED driver with integrated boost controller for medium, large LCD panel backlight based on LED7708 and STM32F103C6T6A Features Data brief Wide DC input voltage: 10 V to 28 V Integrated boost
More informationSC75823E/W. Silan Semiconductors 1/3 DUTY GENERAL-PURPOSE LCD DRIVER HANGZHOU SILAN MICROELECTRONICS CO.,LTD DESCRIPTION FEATURES ORDERING INFORMATION
1/3 DUTY GENERAL-PURPOSE LCD DRIVER DESCRIPTION The is a general-purpose LCD driver that can be used for frequency display in microprocessor-controlled radio receives and in other display applications.
More informationADC Peripheral in Microcontrollers. Petr Cesak, Jan Fischer, Jaroslav Roztocil
ADC Peripheral in s Petr Cesak, Jan Fischer, Jaroslav Roztocil Czech Technical University in Prague, Faculty of Electrical Engineering Technicka 2, CZ-16627 Prague 6, Czech Republic Phone: +420-224 352
More information16-BIT LOAD CELL/DUAL STATUS INPUT
16-BIT LOAD CELL/DUAL STATUS INPUT On-board Excitation. +5VDC, (120mA). State-of-the-art Electromagnetic Noise Suppression Circuitry. Ensures signal integrity even in harsh EMC environments. Optional Excitation
More informationIS01BFRGB LCD SmartDisplay from NKK Switches Simple implementation featuring the ATmega88PA from Atmel Complete software solution
DKAN0003A Controlling the SmartDisplay with a SPI Peripheral 09 June 009 Features IS01BFRGB LCD SmartDisplay from NKK Switches Simple implementation featuring the ATmega88PA from Atmel Complete software
More informationECMF4-20A42N10. Common mode filter with ESD protection for high speed serial interface. Features. Applications. Description
Common mode filter with ESD protection for high speed serial interface Features Datasheet - production data Figure 1. Pin configuration (top view) 5GHz differential bandwidth to comply with HDMI 2.0, HDMI
More informationATA8520D Production and EOL Testing. Features. Description ATAN0136 APPLICATION NOTE
ATAN0136 ATA8520D Production and EOL Testing APPLICATION NOTE Features Test application for production and EOL testing of ATA8520-EK1-E/ EK2-E/ EK3-E evaluation kits PCB component tests, i.e., MCU, temperature
More informationGOPLCP USER'S MANUAL V 0.9 OHO-Elektronik
GOPLCP USER'S MANUAL V 0.9 OHO-Elektronik www.oho-elektronik.de Author: M.Randelzhofer OHO-Elektronik Michael Randelzhofer Rudolf-Diesel-Str. 8 85221 Dachau Germany WEB: www.oho-elektronik.de EMAIL: info@oho-elektronik.de
More informationAN1775 APPLICATION NOTE
AN1775 APPLICATION NOTE STR71x HARDWARE DEVELOPMENT GETTING STARTED INTRODUCTION This application note is intended for system designers who require a hardware implementation overview of the development
More informationObsolete Product(s) - Obsolete Product(s)
STEVAL-IPP001V2 Complete solution for power line communication in metering applications Data brief Features Energy consumption measured by external metering board Power line communication up to 28.8 kbps
More informationDA8-T DA8-T MANUAL
J C F A U D I O MANUAL 1.0 contact@jcfaudio.com www.jcfaudio.com Safety Information Do not repair, modify, service this device except in the manner in which it is described in this manual. Doing so can
More informationPCI Express JPEG Frame Grabber Hardware Manual Model 817 Rev.E April 09
PCI Express JPEG Frame Grabber Hardware Manual Model 817 Rev.E April 09 Table of Contents TABLE OF CONTENTS...2 LIMITED WARRANTY...3 SPECIAL HANDLING INSTRUCTIONS...4 INTRODUCTION...5 OPERATION...6 Video
More informationInstruction Manual AVT-8710 Time Base Corrector
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Instruction Manual AVT-8710 Time Base Corrector Table of Contents 1.0 Introduction
More informationDT9857E. Key Features: Dynamic Signal Analyzer for Sound and Vibration Analysis Expandable to 64 Channels
DT9857E Dynamic Signal Analyzer for Sound and Vibration Analysis Expandable to 64 Channels The DT9857E is a high accuracy dynamic signal acquisition module for noise, vibration, and acoustic measurements
More information1. Overview. SSI-1016G interfaces with 24, 25 and 26 bit Temposonics SSI sensor. Block diagram. as PNP open collector output
SSI-1016G Manual Caution: Specifications and outline may be changed without notice MTS Sensors Technology Corporation www.mtssensor.co.jp 2010.02.04 Rev. 1 1 Revision information 2007.03.12: Data-ready
More information8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT BOARD)
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS LEARN ABOUT PROGRAMMING WITH THIS 8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT
More informationEMB-Z2538PA PRELIMINARY. Datasheet
EMB-Z2538PA PRELIMINARY Datasheet FCC ID: Z7H-EMB2538PA The device complies with part 15 of the FCC Rules. Operation is subjected to the following 2 conditions: (1) this device may not cause harmful interference
More informationImplementing Audio IP in SDI II on Arria V Development Board
Implementing Audio IP in SDI II on Arria V Development Board AN-697 Subscribe This document describes a reference design that uses the Audio Embed, Audio Extract, Clocked Audio Input and Clocked Audio
More informationUniversal ByteBlaster
Universal ByteBlaster Hardware Manual June 20, 2005 Revision 1.1 Amfeltec Corp. www.amfeltec.com Copyright 2008 Amfeltec Corp. 35 Fifefield dr. Maple, L6A 1J2 Contents Contents 1 About this Document...
More informationCheckpoint 2 Video Interface
University of California at Berkeley College of Engineering Department of Electrical Engineering and Computer Sciences EECS150 Fall 1998 R. Fearing and Kevin Cho 1. Objective Checkpoint 2 Video Interface
More informationMemec Spartan-II LC User s Guide
Memec LC User s Guide July 21, 2003 Version 1.0 1 Table of Contents Overview... 4 LC Development Board... 4 LC Development Board Block Diagram... 6 Device... 6 Clock Generation... 7 User Interfaces...
More informationAN2415 Application note
AN Application note Using the output detection feature of the high-brightness LED driver STP0CDC evaluation board Introduction Note: This document describes how to implement a complete solution for driving
More informationEvaluation Board for CS4954/55
Evaluation Board for CS4954/55 Features l Demonstrates recommended layout and grounding practices l Supports both parallel and serial digital video input l On-board test pattern generation l Supports NTSC/PAL
More informationLattice Embedded Vision Development Kit User Guide
FPGA-UG-02015 Version 1.1 January 2018 Contents Acronyms in This Document... 3 1. Introduction... 4 2. Functional Description... 5 CrossLink... 5 ECP5... 6 SiI1136... 6 3. Demo Requirements... 7 CrossLink
More informationHD1-DX HDMI Extender
. HD1-DX HDMI Extender Quick Reference & Setup Guide Magenta Research 128 Litchfield Road, New Milford, CT 06776 USA (860) 210-0546 FAX (860) 210-1758 www.magenta-research.com MAGENTA HD1-DX HDMI EXTENDER
More information5V +10V. Figure 1. DC2622A Connection Diagram
Description Demonstration circuit 2622A features the amplifier. The DC2622A includes two of these amplifiers and is designed to drive the inputs of the DC2290 demo board. The DC2290 features the LTC 2387
More informationMM5452/MM5453 Liquid Crystal Display Drivers
Liquid Crystal Display Drivers General Description The MM5452 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. It is available in a 40-pin molded package.
More informationST25TV02K ST25TV512. NFC Type 5 / RFID tag IC with EEPROM up to 2-Kbit, product identification and protection. Features
ST25TV02K ST25TV512 NFC Type 5 / RFID tag IC with EEPROM up to 2-Kbit, product identification and protection Data brief UFDFPN5 (1.7x1.4 mm) Features Wafer Contactless interface Based on ISO/IEC 15693
More informationBooya16 SDR Datasheet
Booya16 SDR Radio Receiver Description The Booya16 SDR radio receiver samples RF signals at 16MHz with 14 bits and streams the sampled signal into PC memory continuously in real time. The Booya software
More information32 Channel CPCI Board User Manual
0 Sections Page 1.0 Introduction 1 2.0 Unpacking and Inspection 1 3.0 Hardware Configuration 1 4.0 Board Installation 5 5.0 I/O Connections and the Front Panel 5 5.1 Front Panel Layout 5 5.2 Input and
More informationUsing the HT1628 for Washing Machine Panel Display
Using the HT1628 for Washing Machine Panel Display D/N: AN0476E Introduction The HT1628 device is a RAM-mapped multifunction LCD control driver IC which operates with a 1/1 or 1/2 Duty. The device output
More informationAL330B-DMB-A0 Digital LCD Display SOC Demo Board
AL330B-DMB-A0 Digital LCD Display SOC Demo Board User Manual Version 1.2 INFORMATION FURNISHED BY AVERLOGIC IS BELIEVED TO BE ACCURATE AND RELIABLE. HOWEVER, NO RESPONSIBILITY IS ASSUMED BY AVERLOGIC FOR
More informationEXPERIMENT #6 DIGITAL BASICS
EXPERIMENT #6 DIGITL SICS Digital electronics is based on the binary number system. Instead of having signals which can vary continuously as in analog circuits, digital signals are characterized by only
More informationObsolete Product(s) - Obsolete Product(s)
Power over ethernet 10 W module Preliminary data Features Input voltage range: 38.5 V to 60 V 10 W output Based on ST devices integrating standard PoE interface and current mode PVM controller IEEE 802.3af
More informationL, LTC, LTM, LT are registered trademarks of Linear Technology Corporation. Other product
DESCRIPTION WARNING! Do not look directly at operating LED. This circuit produces light that can damage eyes. Demo Circuit 1265 QUICK START GUIDE LTC3220/LTC3220-1 360mA Universal 18-Channel LED Driver
More informationHD/SD-SDI to HDMI adaptor board HD-3000S Manual
HD/SD-SDI to HDMI adaptor board HD-3000S Manual Digital View Ltd Doc Ver 1.01: 7 July, 2017 Page 1 of 15 Table of Contents Introduction 3 Connectors, Pin outs & Jumpers 5 Board Dimensions 10 Signal Support
More information6170 Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2115-202 Upconverter November 2011, Rev. C MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More informationShunt Resistor Measurement Lab. for DE July From. SoftBaugh. Custom Software, Firmware, Hardware, and Project Management Consulting
Shunt Resistor Measurement Lab for DE427 21 July 2004 From SoftBaugh Custom Software, Firmware, Hardware, and Project Management Consulting 4080 McGinnis Ferry Road Suite 604 Alpharetta, Georgia 30005
More informationSC-HD-2A HDMI Scaler & Audio Embedder / Extractor
User s Manual SC-HD-2A HDMI Scaler & Audio Embedder / Extractor Scale HDMI or DVI video Embed Digital or Analog Audio into HDMI output Extract (De-embed) Digital and Analog Audio from HDMI input UMA1246
More informationDLP Pico Chipset Interface Manual
Data Sheet TI DN 2510477 Rev A May 2009 DLP Pico Chipset Interface Manual Data Sheet TI DN 2510477 Rev A May 2009 IMPORTANT NOTICE BEFORE USING TECHNICAL INFORMATION, THE USER SHOULD CAREFULLY READ THE
More informationApplication Note. RTC Binary Counter An Introduction AN-CM-253
Application Note RTC Binary Counter An Introduction AN-CM-253 Abstract This application note introduces the behavior of the GreenPAK's Real-Time Counter (RTC) and outlines a couple common design applications
More informationSpecifications. FTS-260 Series
Specifications DVB-S2 NIM Tuner Date : 2014. 03. 26. Revision F2 #1501, Halla sigma Valley, 442-2 Sangdaewon-dong, Jungwon-gu, Sungnam City, Gyeonggi-do, Korea, 462-807 Tel. 86-755-26508927 Fax. 86-755-26505315-1
More informationInstruction manual Universal Fieldbus-Gateway UNIGATE IC - RS
Instruction manual niversal Fieldbus-Gateway NIGE IC - S rt.-no.: V3504E Carl-Zeiss-Str. 8 D-65520 Bad Camberg el:+49-(0)6434-9433-0 Hotline: +49-(0)6434-9433-33 Fax: +49-(0)6434-9433-40 Internet: http://www.deutschmann.de
More informationUSER'S MANUAL. Getting started with ALEXAN ATMEL AT89C2051/AT89C4051 Training Module - 1
USER'S MANUAL Getting started with ALEXAN ATMEL AT89C05/AT89C405 Training Module - Version.0 Copyright 006 Ace Electronic Technology Inc. All Rights Reserved Alexan 05/405 TM- v..0 Page of 7 About This
More informationSKY LF: 1.5 to 3.8 GHz Two-Stage, High-Gain Low-Noise Amplifier
DATA SHEET SKY67180-306LF: 1.5 to 3.8 GHz Two-Stage, High-Gain Low-Noise Amplifier Applications LTE, GSM, WCDMA, HSDPA macro-base and micro-base stations S and C band ultra-low-noise receivers Cellular
More informationInstruction Manual Model BlockUpconverter
Instruction Manual Model 2115-55 BlockUpconverter June 2009 - Rev. 0 MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More informationWM8725 EVALUATION BOARD USER HANDBOOK. The WM8725 is high performance Stereo DAC.
w WM8725-EVM WM8725 EVALUATION BOARD USER HANDBOOK INTRODUCTION The WM8725 is high performance Stereo DAC. This evaluation platform and documentation should be used in conjunction with the latest version
More informationSTB Front Panel User s Guide
S ET-TOP BOX FRONT PANEL USER S GUIDE 1. Introduction The Set-Top Box (STB) Front Panel has the following demonstration capabilities: Pressing 1 of the 8 capacitive sensing pads lights up that pad s corresponding
More information