How To Build Megavolt s Small Buffered JTAG v1.2

Size: px
Start display at page:

Download "How To Build Megavolt s Small Buffered JTAG v1.2"

Transcription

1 How To Build Megavolt s Small Buffered JTAG v1.2 Abstract A JTAG cable should be considered mandatory equipment for any serious tester. It provides a means to backup the information in the receiver and restore it whenever necessary. This document illustrates the process of building one that is safe to use in any receiver. An illustrated guide by DO999 Revised August 20 th, 2002 Version or

2 Preface... 1 Introduction... 1 Assumptions... 1 Electrical Schematic by SatFTA... 4 Construction General... 5 Construction of the JTAG module... 5 Step 1: Initial assembly of the PCB Step 2: Mount (solder) the main components... 6 Step 3: Connect the parts together Step 4: Add the single 100 Ohm resisitors... 8 Step 5: Creating a grounding strip... 9 Step 6: Connect wire for Vcc (power) and Ground to the circuit... 9 Step 7: IRD JTAG Port Connection Step 8: Computer (PC) Connection Step 9: Completion of JTAG module Installation Installation - PC Connection Mounting the DB Installation - Connecting to the IRD Installation - Power Connection Optional PAD 1 Grounding Switch Installation Internal Mounting Conclusion Troubleshooting Appendix A Images Internal JTAG for a Standalone JTAG that can be used on any IRD IRD JTAG Connection Images Model Model 3100 / Model 5100 / Model Appendix B Detailed Parts List... 22

3 Preface The first thing I want to point out is that this guide is nothing more than an assembly guide. The credit for the actual circuit design goes to SatFTA. These instructions expand on the Megavolt s Small Buffered JTAG v1.2 documents by adding step-by-step pictures and some alternative construction techniques. All the real credit belongs to those SatFTA and MegaVolt. Second, I want to mention that the document is fairly long but hopefully that is due to the level of detail I am putting into it. This project really is fairly simple to construct. Many sections will not apply to you and the JTAG that you will build. You should of course read the entire document before starting construction. This will allow you to get the necessary parts and have a good understanding of the options available to you. Introduction Megavolt set out to create a buffered JTAG without a Printed Circuit Board (PCB), small enough to fit inside a DB25 housing. He was quite successful and the design was brilliantly simple. This guide expands on that by adding in the PCB such that it can be mounted inside the IRD case or a small project box. Examples, information and pictures of various optional parts and mounting techniques will be shown later in this guide. Assumptions It is assumed that the reader has a basic level of soldering skill. The construction is fairly straightforward and with the PCB a beginner should be able to accomplish the task. Knowledge and understanding of electrical diagrams is not required even though they are included in the guide. It is also assumed that you have read Megavolts documents as they provide some details and background that I do not. Some of the information presented here is directly from that document. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 1

4 Purpose In general, the purpose of any JTAG cable (buffered or not) is to read and write the TSOP chip within the receiver (IRD). The most common reason for using the JTAG is to extract the BoxKey information from the IRD. Once you have the BoxKeys, you are able to test options that do not require the use of the smartcard (CAM) such as the Atmega128 or computer emulation software. This connection also allows you to create backup images of the firmware within the unit. The firmware is the program code that basically makes the unit work. It is the equivalent to the operating system that you load onto a computer. Being able to read / write the firmware is important to recover from ECM s or to roll back the firmware to a previous version that may not have anti-testing features in it (like firmware version E338 on the 3100 IRD). In addition, with great software like JKeys by Dave2 you cannot only backup the TSOP (or TSOPs since x100 series IRDs have more than one chip) but you can also read and write the EEPROM chip through the same cable and software. (Note: Wall version 2 also works great on the 3100) If you have read this far you probably already know why you want to build a buffered JTAG. Just in case, the brief rundown is that the buffered JTAG supplies data signals and voltages that are friendly to both the IRD (receiver) and the computer. The simple resistor style JTAG can use in excess of 5V which is greater than the 3.3V used in the TSOP the x100 series IRD and not only can it result in poor reads / writes but it can significantly damage the TSOP. This is not to say that it will absolutely happen, just that it could. The use of a buffered JTAG alleviates these issues. The resistor style JTAG (which I won t get into here) is great on the x700 (and I m sure other types) series IRD. Personally, I had nothing but troubles with the simple JTAG on a 3100 and that is when I was converted and jumped on the buffered JTAG bandwagon. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 2

5 Parts List A detailed parts list, with pictures, is included in the appendix to this document. Part numbers, approximate cost and supplier information can also be found in the appendix. In summary, the following parts will be used: Quantity Description 1 74HCT244 Octal 3-state noninverting line receiver chip 1 2.2K Ohm Bussed 9 resistor network (10 pin Single Inline Package[SIP]) Ohm Isolated 4 resistor network (8 pin SIP) Ohm resistor 1 Printed Circuit Board (PCB) 1 DB25 Connector Male or Female depending on your PC parallel cable 1 6 strip of 6 or 10 conductor ribbon wire. (An old floppy cable works well.) 1 (Optional) DB25 housing Used if you are not mounting the JTAG inside the IRD 1 (Optional) SPDT or SPST switch Used for Power On/Off 1 (Optional) SPDT or SPST switch used to ground Pad 1 on some IRD s. Also a momentary contact switch (push button) works well for this. 1 (Optional) 20-pin socket to mount the chip not required if you solder the chip directly to the PCB 1 (Optional) SIP socket strip with 26 pins not required if you solder the resistor networks directly to the PCB 1 (Optional) Plastic project box required if you are making a portable, external JTAG 6 (Optional) Pogo / Spring pins to connect to IRD JTAG port. Not required for directly soldered cabling. 1 Miscellaneous length of wire, solder, glue or other mounting material 1 (Optional) 3.3V (3.0V to 3.6V) power source. Battery or transformer. Not required for internally mounted JTAG. [2 x AA batteries for an x100 series or 3 x AA batteries for a x700 series IRD work well] An internally mounted JTAG using only the mandatory items listed above will run about $10-$15 Canadian. Obviously, the more optional parts that are used, the higher the cost. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 3

6 Electrical Schematic by SatFTA Here is the overall design of what we are trying to make. If you can follow the directions, it is not necessary to understand this drawing. A simplified drawing mapped onto the board layout would look like this: How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 4

7 Construction General The Buffered JTAG consists of the PCB with the various resistors and chip mounted on it. The connection to the PC DB25, the JTAG port and power will be described as part of the Installation process. Construction of the JTAG module Once again I want to emphasize that these steps are essentially the same as those published by Megavolt with the addition of a PCB. I also chose to build the JTAG using sockets for the components because that is the way I was taught and the pictures are easier to view with them. It is also easier to replace the parts or borrow them for other projects. The main reason for using sockets is to prevent damage to the components from over heating during soldering. Sockets are not required and add to the overall cost of the project. Feel free not to use them. Step 1: Initial assembly of the PCB. Trim (ie cut) legs (pins) 2, 3, 5, 7 & 9 off the 2.2K Ohm resistor network or the SIP socket as shown below. These pins are not required and will get in the way later if not removed. Note that Pin 1 of the resistor network is typically on the left side when viewing the side with printing on it and should be marked with a coloured band or other indicator such as a dot or triangle. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 5

8 Step 2: Mount (solder) the main components Start by placing the chip or the 20-pin socket in the middle of the PCB to allow for other components to be located around the chip. Align the resistor networks or SIP sockets as indicated in the picture. Note the resistor networks/sip sockets should be mounted right beside the chip or 20-pin socket and not as shown. The image simply shows the alignment. See the next image for actual placement. The image below shows the correct placement of the chips / sockets as viewed from the top of the PCB. On the back side of the PCB, solder all pins to the connection points on the PCB but do not bridge solder between any of the pins at this time. There should be 20 solder connections for the 20-pin socket, 5 solder connections for the 10-pin SIP socket (2.2K resistor network) and 8 solder connections for each of the two 8-pin SIP sockets (100 Ohm resistor networks). How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 6

9 Only 5 connection are required for the 2.2K Ohm resistor network because you removed the other unused pins. Step 3: Connect the parts together. Use solder on the back side of the PCB to bridge a circuit between pins 1, 4, 6, 8, 10 of the 2.2K Ohm bussed resistor network and pins 20, 17, 15, 13, 11 of 7444 chip or socket respectively as indicated in yellow below. ie Pin 1 of the resistor network connects to pin 20 of the 74244, pin 4 to pin 17 and so on. Using the same technique extend the solder from pins 4, 6, 8, 10 of 2.2K Ohm resistor network to the adjacent pins (1, 3, 5, 7) of the 100 Ohm resistor network creating a connection across all 3 pins. On the other side of the chip connect pins 3, 5, 7, 9 to pins 1, 3, 5, 7 of the second 100 Ohm resistor network. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 7

10 Step 4: Add the single 100 Ohm resisitors. Solder a 100 Ohm resistor to pin 2 of the chip and a second 100 Ohm resistor to pin 18 of the chip. Note: When installing the resistor connected to pin 18, leave the wire (lead) on the resistor fairly long as you will connect it past the 2.2K resistor network as shown below. Once it is in place, trim the excess wire off with a pair of cutters. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 8

11 Step 5: Creating a grounding strip Connect pins 1, 4, 6, 8, 10, 19 of chip together to form a common grounding point. Use a piece of solid wire and solder it between the pins listed. Make sure the wire does not come in contact with anything else. I left the ground wire long in the image in case I wanted to use it later in the construction process. Step 6: Connect wire for Vcc (power) and Ground to the circuit In preparation for connecting power to the circuit, add a red (Vcc) and black (ground) wire (or any colour) connecting Vcc to pin 20 of the chip and the ground to pin 1 or the grounding strip created in the previous step. Optionally, the Vcc line can be connected to a power switch if you are using a battery so that the circuit can be powered off to the save the life of the battery when not required. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 9

12 Step 7: IRD JTAG Port Connection A 6-wire or 10-wire ribbon cable can be used to connect to the JTAG port on the IRD. This may be soldered directly to the IRD or may be connected via the optional pogo pins. Ultimately, you want this portion or the circuit to be as short as possible. For now, ensure that you will have plenty to work with as you can easily make it shorter later on. If using a 10-wire ribbon cable, connect every second wire to the ground line (not shown). By grounding every second wire you are in effect isolating the signals in the ribbon cable and reducing any noise picked up by the wiring. This makes the signal cleaner and reduces the potential for problem reads or writes. Connect one wire to the grounding strip, four wires one to each of pin 2, 4, 6 & 8 of the 100 Ohm resistor network and the 6 th wire to the single 100 Ohm resistor. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 10

13 Step 8: Computer (PC) Connection Similarly on the other side of the chip you need to connect a cable (such as Cat 5 network cable) to the circuit. A DB25 connection will be installed later and this will be connected to the parallel port on your computer. Connect one wire to pin 19 of the chip, one wire to the 100 Ohm resistor and the remaining 4 wires to pins 2, 4, 6 & 8 of the 100 Ohm resistor network as indicated. Note, when connecting to pin 19 of the chip, skip over the contact for the 2.2K Ohm resistor network. You should have cut that pin off at the beginning so it will not be a problem. You may alternatively connect this wire to any other convenient grounding point. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 11

14 Step 9: Completion of JTAG module. If you used sockets, you may now insert the 3 resistor networks and the chip. This marks the end of the basic module construction. All that is left is to connect it up. Trim the PCB and mount it inside the project box if one is going to be used. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 12

15 Installation Installation - PC Connection A DB25 connector (25-pin) is used to interface to the computer as mentioned previously. This connection will plug into the parallel port on the computer. If you already have a cable on this port then the easiest thing to do is install the corresponding DB25 connector. For example, I have a 25-pin male-to-female straight through cable attached to my parallel port already so I wanted a male DB25 for it to plug in to. There are different types of DB25 connectors. The simplest one is a solder type where you solder the wires onto terminals in the DB25. I used a crimp connector type for mine since I had the parts and crimper tool handy. That is what you will see in the pictures. As indicated below, you need to connect the wires from pins 8, 6, 4 & 2 of the 100 Ohm resistor network to corresponding pins 2, 3, 4, & 5 of the DB 25 connector. Additionally, connect the 100 Ohm resistor to pin 13 of the DB25 and connect a ground wire to pin 25 of the DB25. Important Note: If you need to pass the wiring through a hole in the IRD, the project box or anything else, do so before connecting the DB25. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 13

16 Mounting the DB25 If you are making a stand alone JTAG that will be used on more than one IRD then you probably want to mount the PCB inside a small plastic project box. You could mount the DB25 directly into the wall of the box or drill a hole for a wire and put the DB25 into a housing that you can purchase for a professional look. Similarly, if you are mounting the JTAG inside an IRD you can mount the DB25 in a slot cut into the casing of the IRD or drill a hole to pass the wire through the case and put a housing over the DB25. Cutting a slot for the DB25 in the IRD case can be difficult. Installation - Connecting to the IRD Connecting the ribbon cable to the JTAG port on the IRD can be tricky because not all IRD s have the same configuration and the pinout may change between revisions. However, the basic concept remains the same. You need to connect the ribbon cable to the TMS, TCK, TDI, TDO, ntrst and Ground lines of the IRD. The following chart has been included (thanks to SatFTA) but you should check for a newer version on the internet if your specific model is not included. Additionally, there are a number of ways to connect the ribbon cable to the JTAG port. I built a buffered JTAG that I can use on any IRD (that has a port) by connecting the ribbon cable to pogo pins. This is similar to the commercial ones that you can purchase. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 14

17 My prototype was built using the connector from a commercial JTAG, I simply cut the ribbon cable and connected it to my circuit. The second one I built from scratch. I marked the position of the JTAG pads on a piece of paper and drilled holes into a piece of wood that the pogo pins could fit into. I then used a hot glue gun to build up a block of glue around the pins, which I could shape with a knife and the glue gun. It fits perfectly into the existing opening in the IRD. The 3100 (and 5100) take considerably longer to read / write than the 2700 I started on so I decided to mount a JTAG into the 3100 on a permanent basis. This one I wired directly to the top of the motherboard and I cut a slot into the back casing for the DB25. This section may seem a little vague, but I will leave it up to you to decide how you will connect to the IRD. Pogo pins and direct wiring both have advantages and disadvantages. Installation - Power Connection The chip requires power for the circuit to function. If you are building an external JTAG then the use of a battery or power transformer is necessary. In the two external types that I built I used a 3.5V lithium battery. I installed a switch so that I could power on the circuit only when required to save battery life. If you use a transformer, simply unplug the transformer to cut power, no switch required. On the internally mounted JTAG I found a 3.3V connection on the motherboard (positive (+) side of a capacitor) that I used to power the circuit. I did not see the need for a power switch since powering the circuit should not affect normal operation of the IRD. I connected to capacitor C137 but there are a number of available connection points. A ground point is easy to find. Connect to the side of the casing if you are in doubt Voltages between the range of 3.0V and 3.6V should be fine for the circuit to function normally. Optional PAD 1 Grounding Switch A switch can be used to created a ground connection for Pad 1 on the x700 series IRD s. If the switch is used (on) when A/C power is applied the IRD boots up into a service mode permitting writes to the TSOP. This is particularly useful for internally mounted JTAGS. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 15

18 Installation Internal Mounting If you are installing the module internally, you can use the same type of plastic standoff that is used to mount a motherboard for a computer into a case. A local computer store will probably provide you with a couple at minimal or no cost. Simply trim the plastic tabs to make a flat foot for the module to sit on. Use cable ties to secure the wires to the module and the case. You don t want them lose inside the IRD. Conclusion Now that the JTAG is built and installed, grab a copy of JKEYS (version 2.01 is current as of the time this document was prepared). Grab your BoxKeys and a backup of your TSOPs and EEPROM. You will be able to sleep better at night knowing you can restore these whenever necessary. Troubleshooting An excellent troubleshooting guide can be found at I hope this link stays active for a while. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 16

19 Appendix A Images Internal JTAG for a 3100 The following image shows the mounting and connection points (in general) of the JTAG built to connect to the top of the 3100 motherboard and using a slot cut in the case for the DB25 PC connection. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 17

20 Standalone JTAG that can be used on any IRD This image shows a battery powered JTAG with pogo pins that can be used on any IRD that has a standard JTAG port. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 18

21 IRD JTAG Connection Images The following images show the Pad configuration for a number of IRDs. Model 2700 Note: The 2 images have reversed front / back from each other. Model 3100 / 301 The 3100 has a number of different pin configurations so match the image to your IRD. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 19

22 It is also possible to connect to the inside of the 3100 IRD on the top of the motherboard at the EJTAG port. Note that the connection configuration is completely different from the underside connections. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 20

23 Model 5100 / 501 Model 6000 How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 21

24 Appendix B Detailed Parts List Most of the parts can be found at an electronic store or on the Internet at The PCB is a Radio Shack part and the Pogo pins were obtained from Detailed Parts List Qty Description Image 1 74HCT244 Chip Part No: SN74HCT244N Alternate Parts: 74HC244 Cost: $ K Ohm Bussed 9 resistor network (10 pin SIP) Part No: 4610X (2 per package) Cost: $1.49 per package Ohm Isolated 4 resistor network (8 pin SIP) Part No: 4608X (4 per package) Cost: $1.49 per package Ohm resistors Part No: 1/4W-100R-5 (5 per package) Cost: $1.49 per package Alternate Part: 1/2W resistor as shown V Power Source (Optional) Battery or Transformer 2 x AA batteries (3.0V) or 3 x AA batteries (4.5V) can also be used. How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 22

25 Qty Description Image 6 Pogo (Spring) Pins (Optional) Part No: PP3 Alternate Parts: Other style pogo pins Cost: $0.90 Total Cost: $ DB25 25-pin connector Part No: (Don t know, had some already) Alternate Part: Crimp style instead of solder style. Cost: $3.50 (Approx) 1 DB25 Shell (Optional) Part No: (Don t know, had some already) Cost: $3.50 (Approx) How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 23

26 Qty Description Image 2 SPDT Switch (Optional) Part No: Cost: $5.49 Each Total Cost: $ pin Socket for 74HCT244 (Optional) Part No: DM-320STG30- CF Alternate Parts: Open frame low-profile Cost: $ SIP Socket strip for resistor networks (Optional) Part No: SIP64S-TG30 Cost: $ Project Box (Optional) Part No: K-JM12-IE-000 Alternate Parts: Any small project box Cost: $2.99 How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 24

27 Qty Description Image 1 Circuit Board Part No: A (2 per package) Alternate Parts: Any small project board Cost: $3.49 (Approx) How to build Megavolt s Small Buffered JTAG v1.2 by DO999 Page 25

Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009

Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009 Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that

More information

Bill of Materials: Magic Color PART NO

Bill of Materials: Magic Color PART NO Magic Color PART NO. 2193838 Magic color is a guessing game. With this game you can surprise your friends and leave them with amazement, how the game guesses what they have in their minds. Only two selections

More information

Bill of Materials: Super Simple Water Level Control PART NO

Bill of Materials: Super Simple Water Level Control PART NO Super Simple Water Level Control PART NO. 2169109 Design a simple water controller in which electrodes are required to sense high and low water levels in a tank. Whenever the water level falls below the

More information

Lab 7: Soldering - Traffic Light Controller ReadMeFirst

Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two-way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been

More information

7 SEGMENT LED DISPLAY KIT

7 SEGMENT LED DISPLAY KIT ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SCORE BOARD WITH THIS 7 SEGMENT LED DISPLAY KIT Version 2.0 Which pages of

More information

This Errata Sheet contains corrections or changes made after the publication of this manual.

This Errata Sheet contains corrections or changes made after the publication of this manual. Errata Sheet This Errata Sheet contains corrections or changes made after the publication of this manual. Product Family: DL205 / DL305 Manual Number D2-DCM Revision and Date 2nd Edition; February 2003

More information

Mal-2 assembly guide v1.0

Mal-2 assembly guide v1.0 Mal-2 assembly guide v.0 SONIC POTIONS Schematic and BOM The BOM can be found on Google Docs Prepare the PCB Separate the PCBs using some pliers. PCB We start with the lower PCB and assemble it beginning

More information

Lab 7: Soldering - Traffic Light Controller ReadMeFirst

Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been

More information

Multi-Key v2.4 Multi-Function Amplifier Keying Interface

Multi-Key v2.4 Multi-Function Amplifier Keying Interface Multi-Key v2.4 Multi-Function Amplifier Keying Interface ASSEMBLY & OPERATION INSTRUCTIONS INTRODUCTION The Harbach Electronics, LLC Multi-Key is a multi-function external device designed for the safe

More information

COLOUR CHANGING USB LAMP KIT

COLOUR CHANGING USB LAMP KIT TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE SEE AMAZING LIGHTING EFFECTS WITH THIS COLOUR CHANGING USB LAMP KIT Version 2.1 Index of Sheets TEACHING

More information

OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION INSTALLATION

OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION INSTALLATION OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION The Psidex Audio Laboratory PGP- 1A is a vacuum tube based microphone preamp and program line amplifier designed to provide solid, robust

More information

Tube Cricket Build Guide

Tube Cricket Build Guide Tube Cricket Build Guide The Tube Cricket is a small-wattage amp that puts out about 1 watt of audio power. With a 12AU7 tube-preamp and a JRC386 power amp, the Tube Cricket gives you great tone in a compact

More information

Introduction 1. Green status LED, controlled by output signal ST. Sounder, controlled by output signal Q6. Push switch on input D6

Introduction 1. Green status LED, controlled by output signal ST. Sounder, controlled by output signal Q6. Push switch on input D6 Introduction 1 Welcome to the GENIE microcontroller system! The activity kit allows you to experiment with a wide variety of inputs and outputs... so why not try reading sensors, controlling lights or

More information

Obtained from Omarshauntedtrail.com

Obtained from Omarshauntedtrail.com http://www.cindybob.com/halloween/ledlighting/ledspotlights/ Introduction In our 2005 haunt providing 120V AC power to the various lights and props requiring it became a fairly large problem. Extension

More information

Atari 400/800 Super Color CPU Card

Atari 400/800 Super Color CPU Card Installation Instructions Atari 400/800 Super Color CPU Card Date: 2017, May 3 rd, version 1.1 Author: Jürgen van Radecke (tfhh) Introduction Hi, Thank you for your purchase of a Super Colour CPU Card!

More information

N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB

N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB Kit Components Item Qty Designator Part Color/Marking PCB 1 LCD Display 1 LCD 1602 Volt Regulator 1 U1 78L05, Black TO-92 Prescaler

More information

Pelican PL-957. Adding additional Tos Link (Digital Optical) inputs, and / or IR Remote

Pelican PL-957. Adding additional Tos Link (Digital Optical) inputs, and / or IR Remote Pelican PL-957 Adding additional Tos Link (Digital Optical) inputs, and / or IR Remote Table of Contents: Background;... 2 Section 1: Adding TosLink receivers... 3 Section 2: Adding Remote Capability...

More information

LP-PAN Preamp Kit Assembly Manual

LP-PAN Preamp Kit Assembly Manual LP-PAN Preamp Kit Assembly Manual December 2010 TelePost Incorporated Rev. A9 1 Table of Contents Introduction... 2 Specifications... 3 Parts List... 4 Assembly... 5 Checkout / Schematic... 9 Introduction

More information

DIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX

DIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX DIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX 2015 FRS & MSXpró. Translation by FRS and Supersoniqs. Table of Contents Introduction... 3 Materials needed... 3 Audio volume boost...

More information

ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT

ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT BUILD INSTRUCTIONS Before you start take a look at the Printed Circuit Board (PCB). The components go in the side with the writing on

More information

Total solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL

Total solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL Total solder points: 123 Difficulty level: beginner 1 2 3 4 5 advanced AUDIO ANALYZER K8098 ra audio gea Give your. look high-tech ILLUSTRATED ASSEMBLY MANUAL H8098IP-1 Features & Specifications Features

More information

Scale Track System. 21 Century y Signal System 2-Rail Manual

Scale Track System. 21 Century y Signal System 2-Rail Manual Scale Track System st 21 Century y Signal System 2-Rail Manual TABLE OF CONTENTS Introduction...2-3 Road Signal Board Diagram and Definitions...4-6 Tips for Handling the Circuit Board...6 2-Rail Detector

More information

NewScope-7A Operating Manual

NewScope-7A Operating Manual 2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3

More information

DX-10 tm Digital Interface User s Guide

DX-10 tm Digital Interface User s Guide DX-10 tm Digital Interface User s Guide GPIO Communications Revision B Copyright Component Engineering, All Rights Reserved Table of Contents Foreword... 2 Introduction... 3 What s in the Box... 3 What

More information

DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide

DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide SPECIFICATIONS Noise Figure: < 0.8 db Gain: > 15 db Frequency Range: 3400-3500 MHz Input Voltage: 7-16 VDC Description: The 9ULNACK

More information

Atari PICO Composite Mod Board Installation Instructions:

Atari PICO Composite Mod Board Installation Instructions: Atari PICO Composite Mod Board Installation Instructions: Installation Guide 6 Switch Atari 2600 6 Switch Video Mod Installation Guide Disclaimer: I am not responsible for any damage done to your Atari.

More information

UAV Ultimate Atari Video A7800

UAV Ultimate Atari Video A7800 UAV Ultimate Atari Video A7800 Basic Install guide because this is really easy mod to do! The UAV is a wonderful piece of tech for what it can do. To summarize, the UAV is a replacement video encoder and

More information

Building a MidiBox LCD Cable

Building a MidiBox LCD Cable Building a MidiBox LCD Cable By Jim Henry, 3-Apr-2004 An LCD panel may be connected to the Core module by a 16 conductor flat ribbon cable. A 16 pin insulation displacement connector (IDC) terminates one

More information

MONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS

MONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS MONO AMPLIFIER KIT Version 2.2 Build Instructions

More information

Christmas LED Snowflake Project

Christmas LED Snowflake Project Christmas LED Snowflake Project Version 1.1 (01/12/2008) The snowflake is a follow-on from my Christmas star project from a few years ago. This year I decided to make a display using only white LEDs, shaped

More information

Introduction 1. Green status LED, controlled by output signal ST

Introduction 1. Green status LED, controlled by output signal ST Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away

More information

TECHNOLOGY WILL SAVE US: THE LUMIPHONE

TECHNOLOGY WILL SAVE US: THE LUMIPHONE TECHNOLOGY WILL SAVE US: THE LUMIPHONE This is a step-by-step guide to soldering your own Lumiphone. The equipment you should have at your station: goggles, soldering mat, soldering Iron, solder and side

More information

Pixie Construction Notes

Pixie Construction Notes Pixie Construction Notes PCB V2a February 4 th 2015 Please note that this document is still currently under revision and we apologise for any errors or omissions. Readers should feel free to e-mail any

More information

Video Streamer Modifications

Video Streamer Modifications CB Electronics Video Streamer Modifications CB Electronics Loddonside, Lands End House, Beggars Hill Road, Charvil, Berks RG10 0UD, UK Tel: +44 (0)118 9320345, Fax: +44 (0)118 9320346 URL: www.colinbroad.com

More information

8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT BOARD)

8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT BOARD) ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS LEARN ABOUT PROGRAMMING WITH THIS 8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT

More information

Optimizing BNC PCB Footprint Designs for Digital Video Equipment

Optimizing BNC PCB Footprint Designs for Digital Video Equipment Optimizing BNC PCB Footprint Designs for Digital Video Equipment By Tsun-kit Chin Applications Engineer, Member of Technical Staff National Semiconductor Corp. Introduction An increasing number of video

More information

Documentation VFD clock 8 a clock

Documentation VFD clock 8 a clock Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success

More information

N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012

N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 Kit properly assembled and configured for Standard Serial LCD (LCD Not yet connected) Kit Components Item Qty Designator Part Color/Marking

More information

DIY KIT MHZ 8-DIGIT FREQUENCY METER

DIY KIT MHZ 8-DIGIT FREQUENCY METER This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).

More information

Light Emitting Diodes (LEDs)

Light Emitting Diodes (LEDs) Light Emitting Diodes (LEDs) Example: Circuit symbol: Function LEDs emit light when an electric current passes through them. Connecting and soldering LEDs must be connected the correct way round, the diagram

More information

MAKE AN RGB CONTROL KNOB.

MAKE AN RGB CONTROL KNOB. MAKE AN RGB CONTROL KNOB. This is a knob based colour changing controller that uses a custom programmed microcontroller to pack a lot of features into a small affordable kit. The module can drive up to

More information

Industrial Monitor Update Kit

Industrial Monitor Update Kit Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part

More information

C2 +5V. (14) Vdd (+5 Vdc) (13) OSC1/A7 1.2K (12) 1.2K (11) 1.2K (10) U1 16F628 16F628A 1.2K (1) A2 1.2K (8) 1.2K (7) 1.2K. (Gnd) Vss (5) (6) 1.

C2 +5V. (14) Vdd (+5 Vdc) (13) OSC1/A7 1.2K (12) 1.2K (11) 1.2K (10) U1 16F628 16F628A 1.2K (1) A2 1.2K (8) 1.2K (7) 1.2K. (Gnd) Vss (5) (6) 1. CN1 Power Sw. SW1 CN2 C1 VR1 78L05 or LP2950ACZ- 5.0 +5V.1uf.1uf 9V Battery Fast Scan (Open) Slow Scan (Closed) Activity LED Reserved for LCD Serial Display R1 10K R2 10K SW2 CN3 LD1 R3 (16) (15) OS/A6

More information

Introduction 1. Digital inputs D6 and D7. Battery connects here (red wire to +V, black wire to 0V )

Introduction 1. Digital inputs D6 and D7. Battery connects here (red wire to +V, black wire to 0V ) Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away

More information

Owner s Manual. multiswitch Firmware-Version 1.06 OS- Version 1.02

Owner s Manual. multiswitch Firmware-Version 1.06 OS- Version 1.02 Owner s Manual multiswitch 1.41 Firmware-Version 1.06 OS- Version 1.02 The information contained in this manual is subject to change without prior notice. All rights reserved. Current as of: Juli 19 th

More information

JTAGcable II In Circuit Emulator for Atmel AVR microcontrollers. User s Guide REV 1.0. Many ideas one solution

JTAGcable II In Circuit Emulator for Atmel AVR microcontrollers. User s Guide REV 1.0. Many ideas one solution JTAGcable II In Circuit Emulator for Atmel AVR microcontrollers REV 1.0 User s Guide Evalu ation Board s for 51, AVR, ST, PIC microcontrollers Sta- rter Kits Embedded Web Serve rs Prototyping Boards Minimodules

More information

Build your own: Track Display

Build your own: Track Display Build your own: Track Display! " #! $% $ & ' $ ' ( ) * +, Track Display Manual 0706 web distribution version Table of Contents Section 1 Page 2 Quick Start Guide -Connecting 2 LEDs to Output #1 -Operating

More information

Build Your Own Clone Super 8 Kit Instructions

Build Your Own Clone Super 8 Kit Instructions Build Your Own Clone Super 8 Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.

More information

"Sophisticated Model Railroad Electronics"

Sophisticated Model Railroad Electronics LOGIC RAIL TM "Sophisticated Model Railroad Electronics" TECHNOLOGIES 21175 Tomball Pkwy Phone: (281) 251-5813 Suite 287 email: info@logicrailtech.com Houston, TX 77070 http://www.logicrailtech.com Block

More information

MUK REAR PANEL ASSEMBLY ASSEMBLY INSTRUCTIONS

MUK REAR PANEL ASSEMBLY ASSEMBLY INSTRUCTIONS Rev B. 13 August 2017 ASSEMBLY INSTRUCTIONS The Midnight Ultimate Keyer (MUK) consists of two functional assemblies: Rear Panel containing the interface and power connectors. Front Panel containing the

More information

apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.

apple Service Source Apple Cinema HD Display 23 LCD (ADC) 11 April Apple Computer, Inc. All rights reserved. apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema HD Display 23" LCD (ADC) 2003 Apple

More information

User Guide MD755. Programmable Motion Sensor for BrightSign Solid State Digital Sign Controllers. Overview

User Guide MD755. Programmable Motion Sensor for BrightSign Solid State Digital Sign Controllers. Overview 650 N Main Street Leominster, MA 01453 1-978-534-0400 User Guide MD755 Programmable Motion Sensor for BrightSign Solid State Digital Sign Controllers Overview The MD-755 offers unique motion triggering

More information

QUIZ BUZZER KIT TEACHING RESOURCES. Version 2.0 WHO ANSWERED FIRST? FIND OUT WITH THIS

QUIZ BUZZER KIT TEACHING RESOURCES. Version 2.0 WHO ANSWERED FIRST? FIND OUT WITH THIS TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE WHO ANSWERED FIRST? FIND OUT WITH THIS QUIZ BUZZER KIT Version 2.0 Index of Sheets TEACHING RESOURCES

More information

Bas Gialopsos Atari PureVideo Encoder Module 2600VECr5.2

Bas Gialopsos Atari PureVideo Encoder Module 2600VECr5.2 Bas Gialopsos 2014 Atari PureVideo Encoder Module 2600VECr5.2 Table of Contents Description Disclaimer Technical and Signal Identification Installation Instructions Tools Required Caution Installation

More information

MSP430 JTAG / BSL connectors

MSP430 JTAG / BSL connectors MSP430 JTAG / BSL connectors (PD010A05 Rev-4: 23-Nov-2007) FAQ: Q: I have a board with the standard TI-JTAG pinhead. Can I use your programmer to flash my MSP430Fxx device? A: Yes. You can use any of our

More information

PART. Maxim Integrated Products 1

PART. Maxim Integrated Products 1 9-646; Rev 0; /00 General Description The MAX94 evaluation kit (EV kit) is assembled with a MAX94 and the basic components necessary to evaluate the -bit analog-to-digital converter (ADC). Connectors for

More information

Document Part Number: Copyright 2010, Corelis Inc.

Document Part Number: Copyright 2010, Corelis Inc. CORELIS Low Voltage Adapter Low Voltage Adapter Boundary-Scan Interface User s Manual Document Part Number: 70398 Copyright 2010, Corelis Inc. Corelis, Inc. 12607 Hiddencreek Way Cerritos, CA 90703-2146

More information

RSL MusicPower Plug-In Installation Manual For Naim NAC 72 Preamp

RSL MusicPower Plug-In Installation Manual For Naim NAC 72 Preamp RSL MusicPower Plug-In Installation Manual For Naim NAC 72 Preamp (Updated to reflect the adjustable gain output boards Z200V) www.ryansoundlab.com RSL MusicPower Plug-In Installation Manual for Naim NAC

More information

Nixie Clock Type Frank 2 Z570M

Nixie Clock Type Frank 2 Z570M Assembly Instructions And User Guide Nixie Clock Type Frank 2 Z570M Software version: 7R PCB Revision: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 2 is a compact design with

More information

DDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1

DDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1 DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1.1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be

More information

apple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber Apple Computer, Inc. All rights reserved.

apple Service Source Apple Studio Display 17 LCD (ADC) Updated 6 Decenber Apple Computer, Inc. All rights reserved. apple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber 2004 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Studio Display 17" LCD (ADC) 2003 Apple

More information

This document is intended to provide information to allow the researcher to build their own device.

This document is intended to provide information to allow the researcher to build their own device. SEXTA Construction Notes Tony Barry, Dave Gault Preamble:- SEXTA is a system (hardware device, firmware, and application software) to create and analyse optical timestamps as observed by a camera and recorder.

More information

University of Arizona January 18, 2000 Joel Steinberg Rev. 1.6

University of Arizona January 18, 2000 Joel Steinberg Rev. 1.6 I/O Specification for Serial Receiver Daughter Board (PCB-0140-RCV) (Revised January 18, 2000) 1.0 Introduction The Serial Receiver Daughter Board accepts an 8b/10b encoded serial data stream, operating

More information

"Sophisticated Model Railroad Electronics"

Sophisticated Model Railroad Electronics LOGIC RAIL TM "Sophisticated Model Railroad Electronics" TECHNOLOGIES 21175 Tomball Pkwy Phone: (281) 251-5813 Suite 287 email: info@logicrailtech.com Houston, TX 77070 http://www.logicrailtech.com Block

More information

XTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors

XTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only

More information

AT-AUTO (tm) QRO Keyline Upgrade Kit Installation Manual

AT-AUTO (tm) QRO Keyline Upgrade Kit Installation Manual AT-AUTO (tm) QRO Keyline Upgrade Kit Installation Manual P.O. Box 341543 Beavercreek, Ohio 45434 5 September, 2015 Copyright 2015 ii Contents 1 Introduction 2 1.1 General Description and Purpose........................

More information

A Huf Puf VFO stabilizer for the YAESU FT-707

A Huf Puf VFO stabilizer for the YAESU FT-707 A Huf Puf VFO stabilizer for the YAESU FT-707 Bruno Beckers ON6AB Page 1 The Yaesu FT707 is a good object to add a Huff Puff VFO stabilizer developed by the late Klaas Spaargaren PA0KSB. The version of

More information

Introduction. The Clock Hardware. A Unique LED Clock Article by Craig A. Lindley

Introduction. The Clock Hardware. A Unique LED Clock Article by Craig A. Lindley Introduction As hard as it might be to believe, I have never built an electronic clock of any kind. I've always thought electronic clocks were passe and not worth the time to design and build one. In addition,

More information

R/C Afterburner Light Kit For Electric EDF Jets 2009 Hyperdyne Labs

R/C Afterburner Light Kit For Electric EDF Jets 2009 Hyperdyne Labs R/C Afterburner Light Kit For Electric EDF Jets 2009 Hyperdyne Labs http://www.hyperdynelabs.com Congratulations on purchasing the Afterburner light kit. Your kit is hand assembled in the USA, and we appreciate

More information

Laboratory 10. Required Components: Objectives. Introduction. Digital Circuits - Logic and Latching (modified from lab text by Alciatore)

Laboratory 10. Required Components: Objectives. Introduction. Digital Circuits - Logic and Latching (modified from lab text by Alciatore) Laboratory 10 Digital Circuits - Logic and Latching (modified from lab text by Alciatore) Required Components: 1x 330 resistor 4x 1k resistor 2x 0.F capacitor 1x 2N3904 small signal transistor 1x LED 1x

More information

VU-1 VU Meter Kit Volume Unit Meter

VU-1 VU Meter Kit Volume Unit Meter VU-1 VU Meter Kit Volume Unit Meter Simplicity Counts, Detail Matters. No part of this document may be reproduced, either mechanically or electronically, posted online on the Internet, in whole or in part,

More information

Assembly Instructions

Assembly Instructions Assembly Instructions REP Series Environmentally - Sealed Rectangular Plastic Connectors Hypertac S.A. January 2014 Assembly Instructions REP Series January 2014 1 Table of Contents I. Introduction A.

More information

Alice EduPad Board. User s Guide Version /11/2017

Alice EduPad Board. User s Guide Version /11/2017 Alice EduPad Board User s Guide Version 1.02 08/11/2017 1 Table OF Contents Chapter 1. Overview... 3 1.1 Welcome... 3 1.2 Launchpad features... 4 1.3 Alice EduPad hardware features... 4 Chapter 2. Software

More information

MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz

MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO

More information

MY-HITE ADJUSTABLE TABLE

MY-HITE ADJUSTABLE TABLE MY-HITE ADJUSTABLE TABLE Corner T Leg Base Model Number : FCNAHBT Please Read Instructions Before Use ASSEMBLY INSTRUCTIONS ALL WORKSTYLES WELCOME Thank you for choosing Friant. We appreciate the trust

More information

Nixie Clock Type Quattro'

Nixie Clock Type Quattro' Assembly Instructions And User Guide Nixie Clock Type Quattro' - 1 - Issue Number Date REVISION HISTORY 2 8 Sept 2012 Errors corrected 1 27 July 2012 New document Reason for Issue - 2 - 1.1 Nixie Quattro

More information

Nixie Clock Type Frank 3

Nixie Clock Type Frank 3 Assembly Instructions And User Guide Nixie Clock Type Frank 3 Software version: 7R PCB Version: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 3 is a compact design with all

More information

Modifying the RW1127 and similar TWTs for 24GHz

Modifying the RW1127 and similar TWTs for 24GHz Modifying the RW1127 and similar TWTs for 24GHz Some notes by Brian G4NNS updated after the EME conference. Issue 1.04 During a visit from Johannes DF1OI he explained how Ulli DK3UC had modified Siemens

More information

Evaluation Board For ADF Integrated VCO & Frequency Synthesizer

Evaluation Board For ADF Integrated VCO & Frequency Synthesizer a Evaluation Board For ADF4360-1 Integrated VCO & Frequency Synthesizer EVAL-ADF4360-1EB1 FEATURES Self-Contained Board for generating RF frequencies Flexibility for Reference Input, Output frequency,

More information

POINTS POSITION INDICATOR PPI4

POINTS POSITION INDICATOR PPI4 POINTS POSITION INDICATOR PPI4 Monitors the brief positive operating voltage across points motors when they are switched Lights a corresponding led on a control panel to show the last operation of each

More information

National Wire and Cable and National Cable Molding Headquarters Los Angeles California

National Wire and Cable and National Cable Molding Headquarters Los Angeles California National Wire and Cable and National Cable Molding Headquarters Los Angeles California CAPABILITIES Medical Business Machines Communications Equipment Computer Equipment Audio Systems General Instrumentation

More information

TKEY-K16. Touch CW automatic electronic keyer. (No moving parts no contacts) Assembly manual. Last review: March 15, 2018

TKEY-K16. Touch CW automatic electronic keyer. (No moving parts no contacts) Assembly manual. Last review: March 15, 2018 TKEY-K16 Touch CW automatic electronic keyer (No moving parts no contacts) Assembly manual Last review: March 15, 2018 Commands and use manual of the K16 and Updates and news: www.ea3gcy.com Thanks for

More information

August " BLANK PATCH PANEL FOR STP KEYSTONE JACKS. 19" PATCH PANEL - 24x STP CAT6A PORTS 19" BLANK PATCH PANEL FOR STP KEYSTONE JACKS

August  BLANK PATCH PANEL FOR STP KEYSTONE JACKS. 19 PATCH PANEL - 24x STP CAT6A PORTS 19 BLANK PATCH PANEL FOR STP KEYSTONE JACKS 19" BLANK PATCH PANEL FOR STP KEYSTONE JACKS WITH EXTRA LONG STRAIN RELIEF BAR The 24-port blank patch panel is designed to use with STP keystone jacks. It can hold up to 24 RJ45 keystone jacks. It features

More information

Table 4-1: Rating Levels

Table 4-1: Rating Levels OBJECTIVES 1. Describe various level ratings that apply to telecommunication cables and jacks and identify where each is implemented. 2. Describe the various levels of the cabling category rating systems.

More information

Dust Sensor using GP Y

Dust Sensor using GP Y Dust Sensor using GP Y Dust sensors detect fine dust ( aerosol ) floating in the air. They are used to determine air quality indoor and outdoor. Limits of the GP2Y10 The GP2Y10 sensor was developed to

More information

VU Meter Buffer DIY Kit

VU Meter Buffer DIY Kit VU Meter Buffer DIY Kit Warning This document is distributed for educational purposes only. This equipment operates at potentially lethal voltages. Only trained, qualified personnel should operate, maintain,

More information

CoLinkEx JTAG/SWD adapter USER MANUAL

CoLinkEx JTAG/SWD adapter USER MANUAL CoLinkEx JTAG/SWD adapter USER MANUAL rev. A Website: www.bravekit.com Contents Introduction... 3 1. Features of CoLinkEX adapter:... 3 2. Elements of CoLinkEx programmer... 3 2.1. LEDs description....

More information

Nixie Tube Clock Type Marsden

Nixie Tube Clock Type Marsden Assembly Instructions And User Guide Nixie Tube Clock Type Marsden Software version: RTC-1.3 PCB Revision: 16 Aug 10-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Marsden is a compact design

More information

Kramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher

Kramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in

More information

A Step-by-Step Guide to the CableEye Software

A Step-by-Step Guide to the CableEye Software CableEye SOFTWARE INTRODUCTION A Step-by-Step Guide to the CableEye Software This booklet (formerly Applications Guide) provides a self-guided introduction to CableEye. Use it to learn how the software

More information

VK-P10SE WARRANTY REGISTRATION FORM

VK-P10SE WARRANTY REGISTRATION FORM VK-P10SE WARRANTY REGISTRATION FORM Unit Serial Number: Customer Name: Address: Date of Purchase: Purchased From: Dealer Name: Address: IMPORTANT NOTE: In order to receive the full five-year product warranty,

More information

Complete Train Control. Run Your Trains, Not Your Track!

Complete Train Control. Run Your Trains, Not Your Track! DH166PS Fits Many DCC-Ready HO Locomotives.672 x 1.074 x.259 17.08mm x 27.28mm x 6.6mm Features: FX3 Function outputs for prototypical lighting effects and on/off control: Digitrax Complete Train Control

More information

Model 5250 Five Channel Digital to Analog Video Converter Data Pack

Model 5250 Five Channel Digital to Analog Video Converter Data Pack Model 5250 Five Channel Digital to Analog Video Converter Data Pack E NSEMBLE D E S I G N S Revision 3.1 SW v2.0.1 This data pack provides detailed installation, configuration and operation information

More information

Reaction Game Kit MitchElectronics 2019

Reaction Game Kit MitchElectronics 2019 Reaction Game Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Schematic 3 How It Works 4 Materials 6 Construction 8 Important Information 9 Page 2 SCHEMATIC Page 3 SCHEMATIC EXPLANATION The

More information

DM1624, DM1612, DM812

DM1624, DM1612, DM812 Installation Guide Hardware and Software DM Series Digital Processors models DM1624, DM1612, DM812 LECTROSONICS, INC. 1 Installation Specific Information Only This guide covers only installation related

More information

TVS-2-TAIT VPU-15-TAIT

TVS-2-TAIT VPU-15-TAIT TVS-2-TAIT High Level Rolling Code Scrambler for the Tait Orca & TM-8000 Radios VPU-15-TAIT Voice Inversion Scrambler for the Tait Orca & TM-8000 Radios Manual Revision: 2018-03-05 Rev B Covers Software

More information

DOGM GRAPHIC SERIES 132x32 DOTS

DOGM GRAPHIC SERIES 132x32 DOTS DOGM GRAPHIC SERIES 132x32 DOTS 6.2009 flexible display content! EA DOGM132B-5 + EA LED55x31-W TECHNICAL DATA EA DOGM132W-5 + EA LED55x31-A EA DOGM132W-6 + EA LED55x31-W * HIGH-CONTRAST LCD SUPERTWIST

More information

Galilean Moons. dual amplitude transmutator. DIY ASSEMBLY MANUAL v1.02

Galilean Moons. dual amplitude transmutator. DIY ASSEMBLY MANUAL v1.02 Galilean Moons dual amplitude transmutator DIY ASSEMBLY MANUAL v1.02 Contents Contents... 2 Introduction... 3 Eurorack Kit Assembly... 4 Resistors... 4 IC Sockets... 5 Ceramic/Film Capacitors... 5 Transistors

More information

Parts Checklist - Please note there is no resistor R3. Diodes, LED and transistors are polarized see construction stages

Parts Checklist - Please note there is no resistor R3. Diodes, LED and transistors are polarized see construction stages Xtal Check Kit build Read me first! -------- UPDATED GUIDE------ September 12, 2018--------- The following steps are designed to get your Xtal check kit built and operational. This is a good beginner s

More information

Building the BX24-AHT

Building the BX24-AHT Building the BX24-AHT file:///f /LASER/build-it.htm (1 of 8) [03/04/2002 5:21:52 PM] file:///f /LASER/build-it.htm (2 of 8) [03/04/2002 5:21:52 PM] Tips & Tricks Use a 25W or smaller soldering iron with

More information