HIGHlite 4K Series High Brightness Digital Video Projector

Transcription

1 HIGHlite 4K Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE Rev A Febrary A

2 Abot This Docment Follow the instrctions in this manal careflly to ensre safe and long-lasting se of the projector. Symbols sed in this manal Many pages in this docment have a dedicated area for notes. The information in that area is accompanied by the following symbols: WARNING: this symbol indicates that there is a danger of physical injry to yorself and/or damage to the eqipment nless the instrctions are closely followed. ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock nless the instrctions are closely followed. LASER WARNING: this symbol indicates that there is a potential hazard of eye exposre to laser radiation nless the instrctions are closely followed. NOTE: this symbol indicates that there is some important information that yo shold read. Prodct revision Becase we at Digital Projection continally strive to improve or prodcts, we may change specifications and designs, and add new featres withot prior notice. Legal notice Trademarks and trade names mentioned in this docment remain the property of their respective owners. Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own. Copyright 2018 Digital Projection Ltd. All rights reserved. page i

3 Laser Information RISK GROUP 2 CAUTION Possibly hazardos optical radiation emitted from this prodct. Do not stare at operating lamp. May be harmfl to the eyes. ATTENTION Ce prodit pet émettre des rayonnements optiqes dangerex. Ne pas fixer la lampe en fonctionnement. Pet être nocif por les yex. Cation - se of controls or adjstments or performance of procedres other than those specified herein may reslt in hazardos radiation exposre. page ii

4 Introdction Congratlations on yor prchase of this Digital Projection prodct. Yor projector has the following key featres: 4K-UHD projector. HDBaseT for transmission of ncompressed High Definition Video p to 100 m from the sorce. 3G-SDI with loop-throgh. Edge Blend with black-level correction. Blanking control for cstom inpt window sizing. Cornerstone, Vertical & Horizontal Keystone, Pincshion & Barrel, and Image Rotation. Control via LAN and RS232. Motorised lens mont. Separate control of screen and sorce aspect ratio. Non-linear warp for irreglar projection srfaces. A serial nmber is located on the side of the projector. Record it here: page iii

5 CONTENTS INSTALLATION AND QUICK-START GUIDE...1 WHAT S IN THE BOX?... 3 CONNECTING THE POWER SUPPLY... 4 Voltage selection... 4 PROJECTOR OVERVIEW... 5 Front and rear views... 5 CONTROL PANEL... 6 REMOTE CONTROL... 7 Infrared reception POSITIONING THE SCREEN AND PROJECTOR Roll and pitch CHANGING THE LENS The lens hood Inserting a new lens Removing the lens OPERATING THE PROJECTOR Switching the projector on Switching the projector off Selecting an inpt signal Selecting a test pattern Adjsting the lens Adjsting the image CONNECTION GUIDE...19 SIGNAL INPUTS Digital inpts and otpts Using HDMI/DisplayPort switchers with the projector CONTROL CONNECTIONS LAN connection examples RS232 connection example OPERATING GUIDE...27 USING THE MENUS Opening the OSD Opening a men Exiting mens and closing the OSD Inside a men Accessing sb-mens page iv

6 CONTENTS (contined) Execting commands Editing projector settings Using a slider to set a vale Editing nmeric vales USING THE PROJECTOR Main men Lens men Lens Control Lens Memory Image men Color men Color Space Color Mode Geometry men Aspect Ratio Digital Zoom Overscan Blanking Keystone Corners Rotation Pincshion / Barrel Cstom Warp Arc Edge Blend men Blend Width Black Level Uplift Laser men Setp men ColorMax Power On/Off Clock Adjst OSD Settings Memory Network men PIP men Information men Signal Format System Stats Thermal Stats Factory Reset SERVED WEB PAGES REFERENCE GUIDE...81 CHOOSING A LENS Basic calclation Basic calclation example Fll lens calclation Introdcing TRC Calclating TRC Calclating the throw ratio with TRC Fll lens calclation example SCREEN REQUIREMENTS Fitting the image to the display page v

7 CONTENTS (contined) 4K-UHD images displayed fll width K-UHD images displayed with a height of 2160 pixels K-UHD images displayed fll height Diagonal screen sizes POSITIONING THE IMAGE ASPECT RATIOS EXPLAINED Aspect ratio examples APPENDIX A: LENS PART NUMBERS APPENDIX B: SUPPORTED SIGNAL INPUT MODES D formats SDI Format APPENDIX C: WIRING DETAILS Signal inpts and otpts HDMI 1 and DisplayPort G-SDI In, 3G-SDI Ot Control connections LAN RS Trigger 1 & Trigger IR inpt APPENDIX D: GLOSSARY OF TERMS page vi

8 This page is intentionally left blank.

9 HIGHlite Laser 4K Series High Brightness Digital Video Projector 4 INSTALLATION AND QUICK-START GUIDE

10 IN THIS GUIDE IN THIS GUIDE What s In The Box?... 3 Connecting The Power Spply... 4 Voltage selection...4 Projector Overview... 5 Front and rear views...5 Control Panel... 6 Remote Control... 7 Infrared reception...10 Positioning The Screen And Projector Roll and pitch...12 Changing The Lens The lens hood...13 Inserting a new lens...14 Removing the lens...15 Operating The Projector Switching the projector on...16 Switching the projector off...16 Selecting an inpt signal...17 Selecting a test pattern...17 Adjsting the lens...18 Adjsting the image...18 Installation and Qick-Start Gide

11 IF IN DOUBT, ASK. Digital Projection HIGHlite Laser 4K Series AIR OUT WHAT S IN THE BOX? ER OF GRAVITY What s In The Box? Make sre yor box contains everything listed. If any pieces are missing, contact yor dealer. OF F Pic EN OP ON te M OF F U EN M E OS CL D OS ON IN S CU SH C YN -S FO RE NS IN LE T IN OM ZO IFT ER US T C OU ET ES PR B 2 I2 M HD 3 2 ort yp I pla SD Dis 3G ALT T AL D DR AD L AL ST TE PIP 9 B P2 M CO 6 E EY 8 G P1 M CO 3D 5 7 I DV I4 M -T HDHD R A VG Only one remote will be spplied with the projector. For more information, see Remote Control frther in this gide. AIR IN FO OU A 1 I1 M HD 365 [14.37] T UL FA DE OK IT EX ZE EE FR AIR IN 4 I3 1 M Port HDplay Dis Yo shold save the original box and packing materials, in case yo ever need to ship yor projector. SW 0 LENS EXTENSION SEE TABLE AP 293 [11.54] 2x AAA batteries Remote control Projector User Manal on disc FRONT IR remote control cable [5.57] Important Information 675 [26.57] 280 [11.02] [14.06] [12.09] LENS CENTER AIR IN 49 CFM AIR IN 18 CFM 585 [23.03] 39.6 [1.56] AIR OUT 68 CFM Only one power cable - dependent on the destination territory - will be spplied with the projector. Power cable, North America 155 [6.10] Power cable, Erope 20 [0.79].9 [ Qick-Start Gide Installation69and [7.19] 105 [4.13] Power cable, United Kingdom REAR IR Do not se the short lens hood with the : 1 zoom lens. 750 [29.53] 541 [21.30] 220 [8.66] AIR OUT 23 CFM HDMI cable (701 [27.60]) 22 [0.87] The projector is shipped withot a lens. For frther information abot sing the right lens and hood, see The lens hood frther in this gide. 217 [8.54] [9.15] R IN 2 CFM 9 Power cable, China page 3 ] LENS EXTENSION TABLE

12 CONNECTING THE POWER SUPPLY Connecting The Power Spply Use only the power cable provided. Lift the cable lock p, psh the mains connector in firmly and psh the lock down to secre the cable. Ensre that the power otlet incldes a grond connection as this eqipment MUST be earthed. 1 AC mains inlet with cable lock 1 Handle the power cable careflly and avoid sharp bends. Do not se a damaged power cable. When operating on 110V Light otpt power is redced by approx 30%. Voltage selection The VOLTAGE SELECT switch mst be set to match the power spply yo are sing: Voltage of power spply sed AC100V otlet Position of VOLTAGE SELECT switch AC200V (single phase) otlet Installation and Qick-Start Gide page 4

13 PROJECTOR OVERVIEW Projector Overview Front and rear views 1 Connection panel Do not se the short lens hood with the : 1 zoom lens. 2 Air otlet 3 Control panel For frther information abot sing the right lens and hood, see The lens hood frther in this gide. 4 Power switch and power connection 5 Lens hood 6 Front infrared window 7 Air inlet 8 Air otlet 4 5 Front view 6 9 Rear infrared window 10 Adjstable feet Rear view 10 Installation and Qick-Start Gide page 5

14 CONTROL PANEL Control Panel 1 ON indicator (ble) Behavior Off On Flashing 2 ERROR indicator (red) Behavior Flash once, then pase Flash twice, then pase Flash three times, then pase Flash for times, then pase On 3 STANDBY indicator (green) Behavior Meaning On Flashing Meaning The projector is switched off. The projector is switched ON. The projector is warming p or cooling down. Meaning Laser failre. Cover open. Fan failre. Over temperatre. System error. 4 MENU btton Access the projector OSD (on-screen display). The projector is in STANDBY mode. The projector is in STANDBY mode. It can be switched on with a network command. 5 Navigation (arrow bttons and ENTER) Navigate the OSD and edit settings with the arrows, confirm choice with ENTER. 6 INPUT btton Select inpt sorce ERROR MENU INPUT OUT OUT STANDBY EXIT SHIFT FOCUS IN ZOOM IN Focs IN / OUT Adjst focs. 9 SHUTTER CLOSE OPEN 8 Zoom IN / OUT Adjst zoom. 9 Shtter CLOSE / OPEN Open and close the shtter. 10 POWER btton Switch the projector on and off (in STANDBY mode) 11 EXIT btton Close the OSD. 12 SHIFT btton Press and hold this btton, then press the arrow bttons to move the lens. Installation and Qick-Start Gide page 6

15 REMOTE CONTROL Remote Control 1 Power ON / OFF Trns power on and off. 2 Pic Mte OPEN / CLOSE Shows and hides the projected image. When CLOSE is pressed, the light sorce switches off completely and the screen becomes black OFF ON Pic Mte OPEN CLOSE OSD OFF ON This projector does not se the following options on the remote: HDMI 3 and 4, DVI, VGA, COMP 1, COMP 2, 3D, EYE and SWAP 2 OSD ON / OFF Enable and disable screen timeot messages and control whether to show the OSD dring projection. 4 MENU DEFAULT 8 4 MENU Access the OSD. If the OSD is open, press this btton to go back to the previos men. 5 OK 5 Navigation (arrows and OK) Navigate throgh the mens with the arrows, confirm yor choice with OK. In lens adjstment modes, the arrows are sed to move, zoom or focs the lens. See 11 below. In lens adjstment modes, or when the OSD is not showing, the OK btton switches between modes: Shift Adjstment and Zoom / Focs Adjstment. 6 7 EXIT FREEZE FOCUS LENS INFO RE-SYNC ZOOM EXIT Go p one level in the OSD. When the top level is reached, press to close the OSD. IN SHIFT IN 7 FREEZE Freeze the crrent frame. 8 DEFAULT When editing a parameter, press this btton to restore the defalt vale. 9 INFO Access information abot the projector. 10 RE-SYNC Re-synchronise with the crrent inpt signal. OUT HDMI1 USER PRESET HDMI2 DVI OUT A B C D ALT HDMI3 HDMI4 DisplayPort2 DisplayPort1 HD-T 3GSDI ADDR ALT R G B ALL VGA COMP1 COMP2 TEST D EYE PIP SWAP contines on next page... Installation and Qick-Start Gide page 7

16 REMOTE CONTROL FREEZE RE-SYNC 11 LENS adjstment FOCUS IN / OUT: adjst focs. SHIFT: press and hold this btton, then se the Navigation arrow bttons to move the lens. ZOOM IN / OUT: adjst zoom. 12 USER PRESET A, B, C, D Load ser presets. 13 ALT Press and hold this btton to access alternative fnctions for all bttons with a green label. 11 FOCUS IN OUT LENS SHIFT ZOOM IN OUT For frther information abot ser presets, see Memory in the Operating Gide. This projector does not se the following options on the remote: Inpts HDMI 3 and 4, DVI, VGA, COMP 1, COMP 2, 3D, EYE and SWAP 14 DVI / DisplayPort2 / nmeric inpt 3 There is no DVI inpt on this projector. There is no DisplayPort2 inpt on this projector. 12 USER PRESET A B C D 15 HDMI 2 / HDMI 4 / nmeric inpt 2 Select the HDMI 2 inpt. There is no HDMI 4 inpt on this projector. 16 HDMI 1 / HDMI 3 / nmeric inpt 1 Select the HDMI 1 inpt. There is no HDMI 3 inpt on this projector. 17 TEST / SWAP / nmeric inpt 0 Show a test pattern. Press again to show the next test pattern:...off, White, Black, Red, Green, Ble, CheckerBoard, CrossHatch, V Brst, H Brst, ColorBar, Screen Layot... Use with ALT to switch between the Main and Sb PIP display. HDMI1 HDMI2 DVI HDMI3 HDMI4 DisplayPort2 DisplayPort1 HD-T 3GSDI ALT ALT ADDR R G B ALL VGA COMP1 COMP2 TEST D EYE PIP SWAP contines on next page... Remote control Installation and Qick-Start Gide page 8

17 17 DISPLAYPORT / R / nmeric inpt 4 Select DisplayPort inpt. Use with ALT to trn the Red channel of the display on and off. 18 HD-T / G / nmeric inpt 5 Select the HDBaseT inpt. Use with ALT to trn the Green channel of the display on and off. 19 3GSDI / B / nmeric inpt 6 Select the 3G-SDI inpt. Use with ALT to trn the Ble channel of the display on and off. 20 VGA / 3D / nmeric inpt 7 There is no VGA inpt on this projector. There is no 3D fnction on this projector. REMOTE CONTROL OFF ON Pic Mte OPEN CLOSE OSD Remote control top OFF LENS ON IN IN This projector does not se the following options on the remote: Inpts HDMI 3 and 4, DVI, VGA, COMP 1, COMP 2, 3D, EYE and SWAP 21 COMP1 / EYE / nmeric inpt 8 There is no Component 1 inpt on this projector. There is no EYE swap for 3D fnction on this projector. 22 COMP2 / PIP / nmeric inpt 9 There is no Component 2 inpt on this projector. Use with ALT to switch on Pictre In Pictre (PIP) mode. 23 ADDR / ALL (with red indicator at the top) Assign and nassign an IR remote address. To assign an address: 1. Press and hold this btton ntil the indicator starts flashing. 2. Release this btton and while the indicator is still flashing, enter a two-digit address sing the nmeric inpt bttons. The indicator will flash three times qickly to confirm the change. To nassign an address and retrn to the defalt address 00, Press and hold ALT and this btton simltaneosly ntil the indicator flashes to confirm the change OUT HDMI1 HDMI2 SHIFT USER PRESET DVI OUT A B C D ALT ALT HDMI3 HDMI4 DisplayPort2 DisplayPort1 HD-T 3GSDI ADDR R G B ALL VGA COMP1 COMP2 TEST D EYE PIP SWAP Remote control bottom Installation and Qick-Start Gide page 9

18 REMOTE CONTROL Infrared reception The projector has infrared sensors at the front and back. The angle of acceptance is 40. Make sre that the remote control is within the angle of acceptance when trying to control the projector Infrared reception Installation and Qick-Start Gide page 10

19 POSITIONING THE SCREEN AND PROJECTOR Positioning The Screen And Projector 1. Install the screen, ensring that it is in the best position for viewing by yor adience. 2. Mont the projector, ensring that it is at a sitable distance from the screen for the image to fill the screen. Set the adjstable feet so that the projector is level, and perpendiclar to the screen. The drawing below shows the positions of the feet for table monting, and the fixing holes for ceiling monting. Always allow the projector to cool for 5 mintes before disconnecting the power or moving the projector. 1 For adjstable feet 2 Six M6 holes for ceiling mont The screws shold not penetrate more than 15 mm into the body of the projector. Ensre that there is at least 50 cm (20 in) of space between the ventilation otlets and any wall, and 30 cm (12 in) on all other sides. 1 1 Do not stack more than 3 projectors Installation and Qick-Start Gide page 11

20 POSITIONING THE SCREEN AND PROJECTOR Roll and pitch The projector can be operated in nmeros positions. It is not recommended to position the projector in portrait mode with inpts facing pward, as shown in the diagram Roll Pitch 1 Positions to avoid: inpts side p 2 Recommended positions Installation and Qick-Start Gide page 12

21 CHANGING THE LENS Changing The Lens The lens hood There are two types of lens hood, short and long. The short lens hood is sed with the following lenses: Throw ratios Part nmber 0.77 : 1 fixed lens : 1 zoom lens : 1 fixed lens : 1 zoom lens : 1 zoom lens : 1 zoom lens : 1 zoom lens Projector with short lens hood fitted Before changing the lens, always make sre the projector is switched off and flly disconnected from its power spply. When changing the lens, avoid sing excessive force as this may damage the eqipment. Take care to preserve the original lens packaging and protective caps for ftre se. The long lens hood mst be sed with the following long throw lens: Throw ratios Part nmber : 1 zoom lens Do not se the short lens hood with the : 1 zoom lens. The projector will not power on withot the lens and lens hood fitted. Projector with long lens hood fitted Installation and Qick-Start Gide page 13

22 Inserting a new lens CHANGING THE LENS 1. Insert the lens into the lens apertre, making sre that the plg on the zoom drive mechanism lines p with socket on the right of the lens apertre. Before changing the lens, always make sre the projector is switched off and flly disconnected from its power spply. 2. Rotate the lens clockwise ntil it clicks into place. When changing the lens, avoid sing excessive force as this may damage the eqipment. Take care to preserve the original lens packaging and protective caps for ftre se. Do not se the short lens hood with the : 1 zoom lens. 3. Secre the lens hood to the front of the projector with the screws. The projector will not power on withot the lens and lens hood fitted. Installation and Qick-Start Gide page 14

23 Removing the lens CHANGING THE LENS 1. Loosen the for screws secring the lens hood to the body of the projector. Remove the lens hood. Before changing the lens, always make sre the projector is switched off and flly disconnected from its power spply. When changing the lens, avoid sing excessive force as this may damage the eqipment. Take care to preserve the original lens packaging and protective caps for ftre se. 2. Psh down the lens holder tab. The projector will not power on withot the lens and lens hood fitted. 3. Rotate the lens anti-clockwise. 4. Pll the lens forward to remove it from the lens apertre. Installation and Qick-Start Gide page 15

24 OPERATING THE PROJECTOR Operating The Projector Switching the projector on 1. Ensre a lens is fitted. Connect the power cable between the mains spply and the projector. (See Connecting the power spply above.) Switch on at the switch next to the power connector. 2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following bttons: On the remote control, the ON btton On the projector control panel, the POWER btton. The fans begin working, then the POWER indicator begins flashing green. When the flashing stops, the POWER and LIGHT indicators both light steady green. The projector is switched on. See also Connecting The Power Spply earlier in this gide. The self-test is rnning when all the LEDs on the control panel are lit. Use only the power cable provided. Switching the projector off 1. Press OFF on the remote control or POWER on the control panel, then press again to confirm yor choice. The POWER indicator on the control panel will start flashing amber, the system will go ot and the cooling fans will rn for a short time ntil the POWER indicator goes stready red to indicate that the projector has entered STANDBY mode. 2. If yo need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect the power cable from the projector. Ensre that the power otlet incldes a grond connection as this eqipment MUST be earthed. Handle the power cable careflly and avoid sharp bends. Do not se a damaged power cable. Installation and Qick-Start Gide page 16

25 OPERATING THE PROJECTOR Selecting an inpt signal 1. Connect one or more image sorces to the projector. 2. Select the inpt yo want to display: Press one of the inpt bttons on the remote control. Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Inpt from the main men, press ENTER/OK and then select an inpt signal sing the UP and DOWN arrow bttons. Press ENTER/OK to confirm yor choice. For fll details of how to se the controls and the men system, see the Operating Gide. Selecting a test pattern To display a test pattern: Press TEST on the remote control. Change the test pattern sing the LEFT and RIGHT arrow bttons.test patterns are displayed in the following order: White, Black, Red, Green, Ble, CheckerBoard, CrossHatch, V Brst, H Brst, ColorBar, Screen Layot, Off Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main men, then select a test pattern sing the LEFT and RIGHT arrow bttons. After the final test pattern, the projector exits test pattern mode and retrns to the main image. To view test patterns again, yo need to press TEST again. If yo wish to exit the test patterns before yo reach the final one, press TEST or EXIT at any time. Installation and Qick-Start Gide page 17

26 Adjsting the lens OPERATING THE PROJECTOR The lens can be adjsted sing the Lens men, or sing the lens bttons on the remote control. Lens men The Lens men provides access to the Lens Control setting and the Lens Center command. Lens Control allows Zoom, Focs and Shift adjstment sing the arrow bttons. The setting operates in Zoom/Focs Adjstment and Shift Adjstment mode. Press ENTER/SELECT to switch between the two modes. Remote control Use the remote control to adjst zoom, focs and shift directly, withot opening a men: OK enters lens control, then switches between Zoom/Focs Adjstment and Shift Adjstment. EXIT exits lens control and opens the Lens men. MENU exits lens control and retrns to the main image. The arrow bttons adjst zoom, focs and shift as indicated on the screen. When adjsting focs and zoom, yo may find it sefl to display the CrossHatch test pattern: press TEST on the remote control and navigate throgh the list of patterns sing the LEFT and RIGHT arrow bttons. For fll details of how to adjst the lens sing the remote control, see Remote Control earlier in this gide. Adjsting the image Orientation This can be set from the Setp men. Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Ato-front. Keystone This can be set from the Geometry men. Pictre Settings sch as Gamma, Brightness, Contrast, Satration, He and Sharpness can be set from the Image men. Setp men Geometry men Image men Installation and Qick-Start Gide page 18

27 HIGHlite Laser 4K Series High Brightness Digital Video Projector 4 CONNECTION GUIDE

28 IN THIS GUIDE IN THIS GUIDE Signal Inpts Digital inpts and otpts...21 Using HDMI/DisplayPort switchers with the projector...22 Control Connections LAN connection examples...24 RS232 connection example...25 Connection Gide

29 SIGNAL INPUTS Signal Inpts Digital inpts and otpts 1 HDBaseT Receives digital signal from HDBaseT-compliant devices with LAN connectivity. 2 Ethernet Provides LAN connectivity 3 3G-SDI in 4 3G-SDI ot 5 HDMI I 6 HDMI II Connect a 3G-SDI cable to distribte the 3G-SDI signal to another projector. HDMI 2.0 inpt spporting HDCP2.2. Connect an HDMI cable to the connector. HDMI 2.0 inpt spporting HDCP2.2. Connect an HDMI cable to the connector. 7 DisplayPort DisplayPort 1.2 inpt. Connect a DisplayPort cable to the connector. Spports sorces p to 4K-UHD resoltion at 60 Hz. For simltaneos HDBaseT and LAN connectivity, a third-party distribtion prodct can be tilised to combine HDBaseT video stream with LAN connection for delivery to the projector. For a complete listing of all spported signal inpt modes, see Appendix C: Spported Signal Inpt Modes in the Reference Gide. For a complete listing of pin configrations for all signal and control connectors, see Appendix E: Wiring Details in the Reference Gide Connection Gide page 21

30 SIGNAL INPUTS EDID on the HDMI, DisplayPort inpts If yo are sing a compter graphics card or another sorce that obeys the EDID protocol, the sorce will atomatically configre itself to sit the projector. Otherwise refer to the docmentation spplied with the sorce to manally set the resoltion to the DMD resoltion of the projector or the nearest sitable setting. Switch off the sorce, connect to the projector, then switch the sorce back on again. Using HDMI/DisplayPort switchers with the projector When sing an HDMI/DisplayPort sorce switcher with the projector, it is important to set the switcher so that it passes the projector EDID throgh to the sorce devices. If this is not done, the projector may not be able to lock to the sorce or display the sorce correctly as its video otpt timings may not be compatible with those of the projector. Sometimes this is called transparent, pass-throgh or clone mode. See yor switcher s manal for information on how to set this mode. Additionally, sorces which se HDCP encryption may not display properly when connected to the projector via a switcher. Refer to the switcher s manal for more information. 1 Sorces Switcher 3 Projector EDID EDID EDID EDID The EDIDs in the switcher shold be the same as the one in the projector. Connection Gide page 22

31 CONTROL CONNECTIONS Control Connections 1 HDBaseT/LAN The projector s featres can be controlled via a LAN connection, sing Digital Projection s Projector Controller application or a terminal-emlation program. 2 Ethernet This dedicated LAN connection can be sed if HDBaseT/LAN is already being sed for HDBaseT signal inpt. 3 Trigger 1 & Trigger 2 The Trigger otpts are activated by one of the three following conditions, as set in the Setp men: Screen trigger: can be connected to an electrically operated screen, atomatically deploying the screen when the projector starts p, and retracting the screen when the projector shts down. Aspect ratio trigger: can be sed to control screen shttering for different aspect ratios. RS232 trigger: can be sed to control the screen or screen shttering on receipt of an RS232 command 4 RS232 All of the projector s featres can be controlled via a serial connection, sing commands described in the Protocol Gide. Use a straight-throgh cable to connect directly to a compter. 5 Wired Remote The remote control can be connected sing a standard 3.5 mm mini jack cable (tip-ring-sleeve, or TRS). For a list of all commands sed to control the projector via LAN, see the Protocol Gide. Only one remote connection (RS232 or LAN) shold be sed at any one time. With a LAN connection the projector can serve a web page offering stats and projector controls. Projector Controller is available for download, free of charge, from the Digital Projection website Control connections Connection Gide page 23

32 CONTROL CONNECTIONS LAN connection examples The projector s featres can be controlled via a LAN connection, sing Digital Projection s Projector Controller application or a terminalemlation program. Projector Controller is available for download, free of charge, from the Digital Projection website. Crossed LAN cable Compter Projector Un-crossed LAN cables Compter 1 Hb or LAN Projector 1 LAN Projector Connection Gide page 24

33 RS232 connection example CONTROL CONNECTIONS Straight-throgh cable Compter Projector 1 1 RS232 Connection Gide page 25

34 This page is intentionally left blank. Connection Gide

35 HIGHlite Laser 4K Series High Brightness Digital Video Projector 4 OPERATING GUIDE

36 CONTENTS CONTENTS USING THE MENUS...29 OPENING THE OSD OPENING A MENU EXITING MENUS AND CLOSING THE OSD INSIDE A MENU Accessing sb-mens Operating Gide Execting commands EDITING PROJECTOR SETTINGS Using a slider to set a vale Editing nmeric vales USING THE PROJECTOR...32 MAIN MENU LENS MENU Lens Control Lens Memory IMAGE MENU COLOR MENU Color Space Color Mode GEOMETRY MENU Aspect Ratio Digital Zoom Overscan Blanking Keystone Corners Rotation Pincshion / Barrel Cstom Warp Arc EDGE BLEND MENU Blend Width Black Level Uplift LASER MENU SETUP MENU ColorMax Power On/Off Clock Adjst OSD Settings Memory NETWORK MENU PIP MENU INFORMATION MENU Signal Format System Stats Thermal Stats Factory Reset SERVED WEB PAGES...71

37 USING THE MENUS Using The Mens ERROR STANDBY ON Opening the OSD POWER OFF ON Access the varios mens sing either the projector control panel or the remote control. On either device, press the MENU btton. MENU EXIT Pic Mte OPEN CLOSE OSD The on-screen display (OSD) opens showing the list of available mens. OFF MENU ON DEFAULT INPUT SHIFT Opening a men Move p and down the list sing the UP and DOWN arrow bttons. To open a men, press ENTER on the control panel or OK on the remote control. This gide refers to the above two bttons as ENTER/OK. OUT OUT CLOSE FOCUS IN ZOOM IN Pic Mte OPEN Projector control panel OK EXIT INFO FREEZE RE-SYNC Remote control Main Men Main Men Exiting mens and closing the OSD To go back to the previos page, press EXIT. When yo reach the top level, pressing EXIT will close the OSD. To close the OSD from any page, press MENU. Inpt Test Pattern Lens Image Color Geometry Edge Blend Laser Setp HDMI 1 PIP Information p Network q On-screen display (OSD): top level mens Operating Gide page 29

38 USING THE MENUS Inside a men When yo open a men, the page consists of the following elements: Title bar at the top Shows which men yo have accessed. Highlighted item Available and navailable items Unavailable items appear a pale gray color. Whether an item is available may depend on other settings. The text or symbol to the right of an item shows whether the item: has a vale that can be changed (the crrent vale is shown) opens a sb-men (an arrow btton is displayed) exectes a command (the space to the right of the item is blank). Men Name Highlighted Item Vale Men Item Vale Unavailable Item Vale Slider Vale Sb-men Command The highlighted item has green backgrond. Accessing sb-mens Inside a men Use the UP and DOWN arrow bttons to highlight the sb-men, then press ENTER/OK. Men Name Men Item Vale Execting commands Highlighted Command OK If the item contains a command, highlighting it reveals an OK btton. Press ENTER/OK to execte the highlighted command. Highlighted command Yo may be asked for confirmation. Use the ENTER/OK to confirm, or EXIT to cancel. Command Name WARNING All [Men] vales will be lost. Press OK to confirm Press Exit to cancel Confirmation dialog Operating Gide page 30

39 Editing projector settings If the highlighted men item contains a list of vales to choose from, yo can change the vale by doing the following: 1. Highlight the men item and press ENTER/OK. 2. In the list of vales that opens, se the UP and DOWN arrow bttons to highlight a vale, then press ENTER/OK again to select the highlighted vale. USING THE MENUS Highlighted Item Men Item Men Item Men Name Crrent Vale Highlighted Vale Vale Vale Vale Some men items may be navailable de to settings in other mens. Unavailable men items appear gray. Using a slider to set a vale Some parameters open a slider. To set sch a parameter: 1. Press the LEFT or RIGHT arrow btton, or ENTER/OK. The arrow bttons will open the slider and adjst the vale at the same time. ENTER/OK will open the slider withot altering the initial vale. 2. Use the LEFT and RIGHT arrow bttons to move the slider. 3. When ready, press EXIT to exit the slider and retrn to the men, or press MENU to exit the slider withot showing the men again. Parameter List of vales Vale Slider Editing nmeric vales Some parameters take nmeric vales withot sing sliders - for example, color matching vales or IP addresses. 1. Use the UP and DOWN arrow bttons to highlight the row containing the nmeric field yo wish to edit. 2. Press ENTER/OK to enter edit mode. A nmeric field in edit mode is white text on ble backgrond. 3. In edit mode: Use the UP arrow btton to increase the nmeric vale. Use the DOWN arrow btton to decrease the nmeric vale. 4. Use the LEFT and RIGHT arrow bttons to edit the next or previos nmeric fields within the same row. 5. Once ready, press ENTER/OK to exit edit mode. Operating Gide Data Row x: y: Highlighted Row x: y: Row x: y: Row x: y: Nmeric vales page 31

40 USING THE PROJECTOR Using The Projector Main men Inpt Press ENTER/OK to open the list of available inpts. Use the UP and DOWN arrow bttons to select an inpt from the list, then press ENTER/OK to confirm yor choice. Press EXIT to retrn to the main men. Test Pattern Choose from:...off, White, Black, Red, Green, Ble, Checkerboard, Crosshatch, H Brst, V Brst, Color Bars, Screen Layot. Use the LEFT and RIGHT arrow bttons to switch between vales. Lens, Image, Color, Geometry, Edge Blend, Laser, Setp and Network Press ENTER/OK to open these mens and access varios settings. Inpt Test Pattern Lens Image Color Geometry Edge Blend Laser Setp Network Main Men q HDMI 1 See Signal Inpts in the Connection Gide for frther information abot the available inpts and connections. Selecting a test pattern hides the OSD. Press EXIT to hide the test pattern, and then press MENU to show the OSD. Press the DOWN arrow at the bottom of the page to access additional mens: Main Men PIP and Information Press ENTER/OK to open these mens and access varios settings. PIP Information p Press the UP arrow to retrn to the previos page. Main men, page 1 and 2 Operating Gide page 32

41 USING THE PROJECTOR Lens men Lens Lock When this featre is On, all other Lens men items are disabled. Lens Control Opens a sb-men, see below. Center Lens Lens Lock Lens Control Center Lens Lens Memory Lens Off Centers the lens. Lens Type Choose a UST or a non-ust lens. Lens Memory Opens a sb-men, see next page. Lens Control Lens Control settings operate in Zoom/Focs Adjstment and Shift Adjstment mode. Press ENTER/OK to switch between modes. When in Zoom/Focs Adjstment mode: Use the UP and DOWN arrow bttons to adjst Zoom. Use the LEFT and RIGHT arrow bttons to adjst Focs. When in Shift Adjstment mode, se the arrow bttons to adjst Shift. Zoom Focs Lens Control p t [Enter] Shift Adjstment Lens Control p t Shift q [Enter] Zoom / Focs Adjstment q Operating Gide page 33

42 USING THE PROJECTOR Lens men contined from previos page Lens Memory This men allows yo to load, save and delete p to ten lens presets, containing position, zoom, focs and shift adjstment information. For example, if sing different screen sizes and aspect ratios, yo can save zoom, focs and positioning for each screen size and aspect ratio in a dedicated preset. Use Clear Memory to delete a memory preset if yo need to save a new combination of lens settings in its place. Overwriting a saved memory preset is not possible. Load Memory Save Memory Clear Memory Lens Memory Lens Load Memory Lens Save Memory Lens Clear Memory Memory 1 OK Memory 1 OK Memory 1 OK Memory 2 Memory 2 Memory 2 Memory 3 Memory 3 Memory 3 Memory 4 Memory 4 Memory 4 Memory 5 Memory 5 Memory 5 Memory 6 Memory 6 Memory 6 Memory 7 Memory 7 Memory 7 Memory 8 Memory 8 Memory 8 Memory 9 Memory 9 Memory 9 Memory 10 Memory 10 Memory 10 Operating Gide page 34

43 Image men Dynamic Black Set to On to allow for increased contrast in darker scenes by modlating the light sorce. Light Off Timer When Dynamic Black is On, the Light Off Timer will define if laser light sorce will trn off after a period of time has passed. The options are: Disable, 0.5, 1.0, 1.5, 2.0, 3.0, 4.0 seconds. Gamma Choose a de-gamma crve from 1.0, 1.8, 2.0, 2.2, 2.35, 2.5, S-Crve, and DICOM. Used correctly, the Gamma setting can improve contrast while maintaining good details for blacks and whites. If excess ambient light washes ot the image and it is difficlt to see details in dark areas, lower the Gamma setting to compensate. This improves contrast while maintaining good details for blacks. Conversely, if the image is washed ot and nnatral, with excessive detail in black areas, increase the setting. S-Crve is an enhanced mid-tone gamma. DICOM is a simlated DICOM display, which can be sed for training applications. HDR Choose an HDR setting from AUTO, HDRPQ-400, HDRPQ-500, HDRPQ-1000 and HDRHLG Ato is the defalt setting. When a 4KUHD Ble-Ray player sends an HDR flag to the projector it will select the appropriate option according to the player data. HDR (High Dynamic Range) is a new form of gamma developed to create more realistic experience when viewing images delivered sing this format, sch as scenes with bright snlight. Unlike traditional gamma, HDR is not device or installation independent. HDR content will come with a recommended brightness regardless of screen size. For best reslts as a gideline the following screens sizes are sggested. USING THE PROJECTOR Dynamic Black Gamma Brightness Contrast Satration He Sharpness Noise Redction Freeze Image Off Light Off Timer Disable 2.2 HDR Ato Resync Off Selecting an HDR setting will disable the Gamma setting. If the HDR setting is Ato, the Gamma setting is only disabled when the image sorce is HDR. Operating Gide page 35

44 USING THE PROJECTOR HDR Screen sizes Screen width (cm) Model Lmens 400 NIT 500 NIT 1000 NIT HLL4K 12, cm 343cm 243cm HDR options shold only be sed with media players and sorces eqiped with HDR and HDR content. Perceptal Qantizer (PQ) is the digitizing concept for captre and display and provides metadata to enable the display to nderstand the coding of the content. The NIT nmbers relate to the brightness of the viewing conditions in NIT. NIT is the nit of brightness measrement for monitors and LED walls that emit light rather than reflect it sch as a projection screen. However it is a reference to the brightness yo wold choose for a given environment. HDRHLG is High Dynamic Range hybrid-log-gamma. This is a broadcast version of HDR for live TV and events Crrently HDR gamma selection is manal. Brightness, Contrast, Satration, He, Sharpness Highlight the setting yo wish to edit, and then press ENTER/OK, or the LEFT or Brightness 100 RIGHT arrow btton to open the slider. Use the LEFT and RIGHT arrow bttons to adjst the slider. Press EXIT to close the slider and retrn to the men, or MENU to close the slider and retrn to the projected image. Noise Redction Choose a level of noise redction from Off, Low, Middle and High. Freeze Freezes the crrent frame. Resync Press ENTER/OK to force the projector to resynchronise with the crrent inpt. Operating Gide page 36

45 USING THE PROJECTOR Color men Color Color Space In most cases, the Ato setting determines the correct colorspace to se. If it does not, yo can choose a specific colorspace: Choose from Ato, YPbPr, YCbCr, RGB PC and RGB Video. Color Space Color Mode ColorMax Manal Color Matching Color Temperatre Ato ColorMax Peak Native Color Space is not available with HDMI 3 or HDMI 4. Gains and Lifts Color Color Space Ato Color Mode ColorMax Manal Color Matching Color Temperatre Gains and Lifts Ato ColorMax Native YPbPr Peak Ato 100 YCbCr 100 RGB Native PC 100 RGB Video Operating Gide page 37

46 USING THE PROJECTOR Color Mode The projector can work in the following color modes: ColorMax, Manal Color Matching, Color Temperatre and Gains and Lifts. Color Color Space Ato Color Mode ColorMax ColorMax ColorMax Manal Color Matching Manal Color Matching Color Temperatre Color Temperatre Gains and Lifts Gains and Lifts Only one color mode can be selected at a time. Settings sed by the other color modes are disabled. ColorMax 1. Set Color Mode to ColorMax. 2. Navigate to the ColorMax setting. Choose from REC709, EBU, SMPTE, Peak, User 1 and User 2. User 1 and User 2 are ser-defined color gamts set via the Setp > ColorMax men. Color Color Space Ato Color Mode ColorMax ColorMax Peak Manal Color Matching HDTV Color Temperatre EBU Gains and Lifts User 1 Peak User 1 User 2 See Setp men for frther information abot setting p the User 1 and User 2 color gamts. Operating Gide page 38

47 USING THE PROJECTOR Color men contined from previos page Manal Color Matching 1. Set Color Mode to Manal Color Matching. Manal Color Matching Ato Test Pattern Off 2. Open the Manal Color Matching sbmen. Red Green Here yo can do the following: Switch Ato Test Pattern On and Off. Adjst He, Satration and Gain settings for each individal color to improve the color balance of the projected image. Adjst white balance RGB vales. Reset all vales. Ble Yellow Cyan Magenta White Balance Reset For more details abot the He, Satration and Gain settings, see Color matching parameters explained frther in this gide. Manal Color Matching Red Manal Color Matching White He 100 Red 100 Satration 100 Green 100 Gain 100 Ble 100 Operating Gide page 39

48 USING THE PROJECTOR Color men contined from previos page Color matching parameters explained The levels of he, satration and gain in the Manal Color Matching men change the color vales in the following ways: He Specifies the position of each color (red, yellow, green, cyan, ble and magenta) relative to its neighboring colors. MAGENTA RED YELLOW RED 2 Satration Specifies the level of white in each color (i.e. how pale each color is). 3 Gain Controls the amont of light that goes into each color, i.e. the lowest gain wold prodce black. WHITE BLUE GREEN BLACK CYAN Operating Gide page 40

49 USING THE PROJECTOR Color men contined from previos page Color Temperatre 1. Set Color Mode to Color Temperatre. 2. Navigate to the Color Temperatre setting. Choose a vale from 3200K (warmer) to 9300K (cooler) or Native (no correction). Color Color Space Color Mode ColorMax Manal Color Matching Color Temperatre Gains and Lifts Ato Color Temperatre Peak Native 3200K 5400K 6500K 7500K 9300K Native Operating Gide page 41

50 USING THE PROJECTOR Color men contined from previos page Gains and Lifts Lifts allow yo to adjst black levels of individal colors, while gains adjst the bright part of the scale. Set the sliders as reqired. Red Lift Green Lift Ble Lift Red Gain Green Gain Ble Gain Reset Gains and Lifts Operating Gide page 42

51 USING THE PROJECTOR Geometry men This men allows yo to compensate for image distortions cased by an nsal projection angle or irreglar screen srface. Aspect Ratio Digital Zoom Overscan Geometry Sorce Off Aspect Ratio, Digital Zoom and Overscan are not available with inpt HDMI 3 or HDMI 4. Blanking Keystone 4 Corners Rotation Pincshion / Barrel Arc Cstom Warp Only one of the following shold be sed at any one time. Keystone, 4 Corners, Rotation, Pincshion/Barrel and Arc For more complex adjstments se Cstom Warp later in this section. Aspect Ratio This featre defines the aspect ratio of the sorce. Use the Setp > Screen Setting to define the screen aspect ratio. If yo choose a preset aspect ratio from here, it will give yo the best fit for yor selection. Choose from: 5:4 4:3 16:10 16: TheaterScope Sorce Unscaled Image scaling and aspect ratio are also inflenced by Setp > Screen Setting. See next page for frther information abot the TheaterScope aspect ratio. Operating Gide page 43

52 USING THE PROJECTOR Theaterscope setting The TheaterScope setting is sed in combination with an anamorphic lens to restore 2.35:1 images packed into a 16:9 frame. Sch images are projected with black lines at the top and bottom of the 16:9 screen to make p for the difference in aspect ratios. Withot an anamorphic lens and withot the TheaterScope setting applied, a 16:9 sorce containing a 2.35:1 image looks like this: Black margin part of the sorce TheaterScope is sed with an anamorphic lens. If yo se TheaterScope, set yor screen aspect ratio to 16:9. Black margin part of the sorce If we change the setting to TheaterScope, the black lines will disappear bt the image will stretch vertically to reach the top and bottom of the DMD : An anamorphic lens will stretch the image horizontally, restoring the original 2.35 ratio: Operating Gide page 44

53 USING THE PROJECTOR.Geometry men contined from previos page Digital Zoom Digital zooming enlarges a section of the image, while the area otside the enlarged section is cropped ot to preserve the overall image size. Digital Zoom defines the level of zoom that needs to be applied. If Digital Zoom is set to 0, then the other settings in the men will be disabled. Digital Pan and Digital Scan specify the area that is being enlarged: Digital Pan adjsts the horizontal coordinates. Digital Scan adjsts the vertical coordinates. Digital Zoom Digital Pan Digital Scan Reset Digital Zoom Digital Zoom is a temporary setting and not retained after an inpt change or power cycle. The Reset command restores the defalt Digital Zoom, Digital Pan and Digital Scan vales. Operating Gide page 45

54 USING THE PROJECTOR Geometry men contined from previos page Overscan Use this setting to compensate for noisy or badly defined image edges. Crop removes nwanted artifacts from the edges of yor image by cropping the edges. Zoom increases the size of the image to force the edges off-screen. Geometry Aspect Ratio Sorce Digital Zoom Overscan Off Blanking Off Keystone Crop 4 Corners Zoom Rotation Pincshion / Barrel Arc Cstom Warp Image with noisy edges Overscanned image Operating Gide page 46

55 USING THE PROJECTOR Geometry men contined from previos page Blanking Use this featre to: fit an odd-sized screen; ct off timecode dots in the top line of a pictre; ct off sbtitles, etc. Select the edge yo wish to blank and se the LEFT and RIGHT arrow bttons to determine the amont of correction. Use the Reset command to restore blanked edges. Top Bottom Left Right Reset Blanking Operating Gide page 47

56 USING THE PROJECTOR Geometry men contined from previos page Keystone Use this setting to compensate for any distortion cased by the projector being in a different horizontal or vertical plane to the screen. H Keystone V Keystone Rotation Reset Keystone Keystone example 1 The projector is positioned at an angle 2 The reslting image is distorted 3 The image is corrected when Keystone is applied Operating Gide page 48

57 USING THE PROJECTOR Geometry men contined from previos page Keystone settings 1 Projector to the left The projector is positioned to the left of the screen. To correct, apply a positive Horizontal Keystone vale sing the RIGHT arrow btton. 2 Projector to the right The projector is positioned to the right of the screen. To correct, apply a negative Horizontal Keystone vale sing the LEFT arrow btton. 3 Projector high The projector is positioned above the screen at a downward angle. To correct, apply a negative Vertical Keystone vale sing the DOWN arrow btton. 4 Projector low The projector is positioned below the screen at an pward angle. To correct, apply a positive Vertical Keystone vale sing the UP arrow btton Projector straight The projector is directly opposite the screen at a right angle both horizontally and vertically. No correction is needed Horizontal and vertical keystone corrections Operating Gide page 49

58 USING THE PROJECTOR Geometry men contined from previos page 4 Corners For each corner, apply horizontal and / or vertical correction as necessary to restore the rectanglar shape of the image. Top Left Corner Top Right Corner Bottom Left Corner Bottom Right Corner Reset 4 Corners Corner corrections provide a simple setp for awkward installations and irreglar shaped screens that may distort the image. To apply a similar (bt less flexible) correction, while preserving the original aspect ratio of the image, se the Keystone men. Top Right Corner example In this illstration, the top right corner reqires both horizontal and vertical correction. Top Right Corner Adjstment Top Right Corner x t 0 Top Right Corner y p 0 q Top Right Corner correction Operating Gide page 50

59 USING THE PROJECTOR Geometry men contined from previos page Rotation Use this featre for example to correct a monting error casing the image not to be level with the screen. Rotation example 1 DMD area The DMD is not rotated. It still covers the area that wold be occpied by the image withot correction. 2 Rotated image The image is smaller than the srronding DMD area. It is scaled in order to remain within the DMD area. 3 Angle of rotation The angle eqals a qarter of the Rotation setting. In this example the angle is 5, therefore Rotation = 20. Rotation Reset Rotation Operating Gide page 51

60 USING THE PROJECTOR Geometry men contined from previos page Pincshion / Barrel Pincshion or barrel distortions are the reslt of poor or incorrect tensioning of the screen or sing a srface that is not flat. Use the Pincshion / Barrel control to compensate electronically for sch distortions. Yo can also se this men to make simple panoramic screen corrections withot sing external processors. Pincshion / Barrel H Pin/Barrel 0 V Pin/Barrel 0 Keystone Reset Pincshion / Barrel example The illstration shows pincshion and barrel correction applied both horizontally and vertically, in eqal measres. Pincshion Barrel Operating Gide page 52

61 USING THE PROJECTOR Geometry men contined from previos page Arc This featre is similar to Pincshion / Barrel bt allows yo to apply crvatre to each edge of the image independently so yo can have any combination of corrections. Arc Top 0 Bottom 0 Left 0 Right 0 Reset Please note that a positive Arc vale on any edge will redce the image size as the projector needs to maintain the aspect ratio. A negative Arc vale will not affect the overall image size. Operating Gide page 53

62 USING THE PROJECTOR Geometry men contined from previos page Cstom Warp This featre permits selection of predefined User warp maps. User cstom warp maps reqire the Projector Controller PC application to create the cstom warp. Cstom warp maps provide non-linear crvatre correction for crved or spherical screens and other irreglar shaped srfaces sch as bilding mapping Off User 1 User 2 Cstom Warp Operating Gide page 54

63 USING THE PROJECTOR Edge Blend men Use this men to blend together images from an array of two or more projectors. The featre feathers the light otpt of the projector within the edges that overlap with other projectors in the array: as a reslt, the overlapping edges are evenly lit and easily blend in with the rest of the image. Edge Blend Edge Blend On Align Pattern Off Blend Width Black Level Uplift When Edge Blend is set to Off, all other edge blend settings are disabled. Edge Blend Enable and disable Edge Blend Align Pattern Add markers to the image showing the edges of the blend area and making the overlaps more visible to help adjst the physical position of the projectors in the array. Blend Width Determine the width of the blended regions. Black Level Uplift Adjst black levels to compensate if the blended regions appear brighter than the rest of the image. Reset Reset all Edge Blend settings to their factory defalt vales. Reset The pictre in the blend region needs to be delivered to all overlapping projectors, which may reqire a special setp of the sorce. Operating Gide page 55

64 USING THE PROJECTOR Edge Blend men contined from previos page Blend Width Use the LEFT and RIGHT arrow bttons to set the width of the blended regions: Top Bottom Left Right Blend Width Top Bottom 3 Left 4 Right 3 4 Operating Gide page 56

65 USING THE PROJECTOR Edge Blend men contined from previos page Black Level Uplift Black in the blended regions appears less dark than in the rest of the image. To compensate for this, se this men to raise the black levels of the rest of the image: Set All to the reqired amont of black level correction. This will apply eqal correction to the black levels of all colors. If necessary, se the individal color sliders (Red, Green and Ble) for fine adjstment. Yo may experience artifacts at the edges where the blended region of one projector overlaps the pond of mirrors of its neighbor. In the example below, the blended image comes from two projectors, 1 and 2. Both images have black level plift applied; as a reslt, artifacts 3 and 4 have emerged at the edges where the black level plift region of one projector overlaps the pond of mirrors of the other. To remove the artifacts, yo need to slightly redce the size of the black level plift region of each projector so it does not overlap the pond of mirrors of the other projector. Depending on yor array, se Top, Bottom, Left and/or Right to redce the black level plift size. In the example below, se the Right slider of the projector on the left 1 to remove the artifact on the right 4, and the Left slider of the projector on the right 2 to remove the artifact on the left 3. Black Level Uplift Select Area Top 0 Bottom 0 Left 0 Right 0 Color Adjstment All t Red 0 Green 0 Ble 0 Enable Align Pattern from the Edge Blend men to see the black level plift area Operating Gide page 57

66 Laser men USING THE PROJECTOR Laser Power Mode Eco will atomatically set the laser power to 80%. Normal will set the power to 100%. Set to Cstom if yo wish to adjst the power manally. Power Mode Power Level Normal Power Level This setting is only available if Power Mode is set to Cstom. Choose a vale between 20 and 100, ranging from 20% to 100% laser power. Operating Gide page 58

67 USING THE PROJECTOR Setp men Setp Orientation Choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Ato-front. High Altitde Choose from On, Ato and Qiet. Standby Power Choose from SperECO, ECO and Normal. SperECO ses minimal power and disables power ON via LAN. ECO ses a low power setting bt enables power ON via Ethernet port only. Normal enables power ON via both HDBase-T/LAN and Ethernet ports. Screen Setting Choose from 16:10, 16:9 and 4:3. ColorMax Set p ser-defined color gamt vales. Power On/Off Management Access the sbmen to set p atomatic projector power on and power off. Clock Adjst Access the sbmen to set crrent date and local time. Startp Logo Set this to On if yo want the DP logo to show when the projector is first switched on. Blank Screen Choose from Logo, Black, Ble and White. Ato Sorce If this setting is On, the projector will atomatically search for an active inpt sorce. Orientation High Altitde Standby Power Screen Setting ColorMax Power On/Off Management Clock Adjst Startp Logo Blank Screen Ato Sorce q Ato-front Ato SperECO 16:9 On Logo Off Ato-front atomatically detects the projector s position and sets Table or Ceiling orientation accordingly. Highlight the DOWN arrow at the bottom of the page and press ENTER/OK to navigate to the second Setp men page. Operating Gide page 59

68 USING THE PROJECTOR Setp men contined from previos page Trigger1 and Trigger 2 Choose from Screen, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35, TheaterScope, Sorce, Unscaled or RS232 to determine what will case each trigger otpt to activate. Infrared Remote Set to Off if yo wish to disable the remote control. IR Code The projector and the remote control need a matching IR code: a two-digit nmber between 00 and 99. The defalt IR code is 00. This is also a master code, which, if assigned to a remote, will work regardless of the vale assigned to the projector. To assign an IR code for the projector: 1. Select IR Code. 2. Use the UP and DOWN arrow bttons to change the vales. To assign an IR code for the remote: 1. Press and hold the ADDR btton on the remote ntil the indicator starts flashing. 2. Release the ADDR btton and while the indicator is still flashing, enter a twodigit address sing the nmeric inpt bttons. The indicator will flash three times qickly to confirm the change. IR Code Reset Use this command to nassign an IR code from the projector. This will revert the IR Code vale to 00. Trigger-1 Trigger-2 Infrared Remote IR Code IR Code Reset OSD Settings Memory Instant Startp Standby Period Setp p Off Off On 0 If yo trn the remote control off, yo can only trn it back on again from the control panel or via the Projector Controller application. The Projector Controller software is available for download from the Digital Projection website, free of charge. Off 30 Min. A wired remote control will also be disabled if Infrared Remote is set to Off. To nassign an IR code from the remote control, Press and hold ALT and ADDR simltaneosly ntil the indicator flashes to confirm the change. OSD Settings Access this sbmen to adjst the appearance and position of the on-screen display. Memory Access this sbmen to save p to for presets containing cstom combinations of image settings, or to recall a saved preset. Instant Startp When ON only the Laser will be trned off when the Power off command is given. A sbseqent Power On will trn on the laser giving an apparent very fast power on. Operating Gide page 60

69 USING THE PROJECTOR Setp men contined from previos page Standby Period Used with Instant Startp. If Instant Startp in ON and the projector is powered down then the projector will go to Standby after the selected Standby Period 30 mintes, 60 mintes, 90 mintes. Highlight the UP arrow at the top of the page and press ENTER/OK to go back to the first Setp men page. Operating Gide page 61

70 USING THE PROJECTOR Setp men contined from previos page ColorMax ColorMax permits seven point color matching of red, green, ble, yellow, cyan, magenta and white. Yo can enter yor own gamt vales here, or edit vales yo have imported sing the Projector Controller software. Measred Data Target Data User 1 Target Data User 2 ColorMax The Projector Controller software is available for download from the Digital Projection website, free of charge. Defining yor own colorspace with individal x and y coordinates for each color enables yo to match not only the whites bt each individal color as well. Highlight the sbmen yo wish to open and press ENTER/OK to confirm yor choice. This tool is best sed in conjnction with a specialized light meter (a photo spectrometer) to measre color parameters within a particlar installation. However, the preloaded generic factory defalt data set is designed to give more than satisfactory reslts. Measred Data / Target Data Measred Data Target Data User 1 1. Use the UP and DOWN arrow bttons to highlight a color, then se the LEFT and RIGHT arrow bttons to navigate to the x or y coordinate. 2. Use the UP and DOWN arrow bttons to increase and decrease the vale, respectively. 3. Exit edit mode: press ENTER/OK, if yo want to save the edited vales. press EXIT, if yo do not wish to save the edited vales Red 4. If necessary, highlight another color and repeat the procedre. x: y: Green Ble x: x: y: y: White x: y: Reset Red x: y: Green x: y: Ble x: y: Yellow x: y: Cyan x: y: Magenta x: y: White x: y: Operating Gide page 62

71 USING THE PROJECTOR Setp men contined from previos page Power On/Off Ato Power Off Set this to On if yo want the projector to go into STANDBY mode when no inpt sorce is detected for 20 mintes. Ato Power On Set this to On if yo want the projector to start p immediately when the mains is connected. Set this to Off if yo want the projector to go into STANDBY mode when the mains is connected. In this case, the projector will not start p ntil the POWER btton is pressed on the control panel or the ON btton is pressed on the remote control. Power On/Off Management Ato Power Off Off Ato Power On Off Schedled on/off Schedled on/off Access this sbmen to create a weekly schedle for atomatic on and off times: 1. Set a schedle: Use the UP and DOWN arrow bttons to highlight a row, then press ENTER/OK to enable edit mode. Within a row, navigate with the LEFT and RIGHT arrow bttons. Set vales with the UP and DOWN arrow bttons. To exit edit mode, press ENTER/OK. Alternatively, press EXIT if yo don t want the changes to take effect. Move to another row sing the UP and DOWN arrow bttons. 2. To enable the schedle, set Schedle to On. Schedled on/off Schedle Off S M T W T F S Time On T 12: 34 Off T 12: 34 On T 12: 34 Off T 12: 34 Operating Gide page 63

72 USING THE PROJECTOR Setp men contined from previos page Clock Adjst Use this men to set date (in dd:mm:yyyy format), time (in HH:mm format) and time zone. The date and time set here will affect any schedle created within the Power On/Off men. Clock Adjst Date (dd:mm:yyyy) 30:11:2017 Time (HH:mm) 16:00 Time Zone UTC 00 Operating Gide page 64

73 USING THE PROJECTOR Setp men contined from previos page OSD Settings Langage sets the OSD langage. Men Position determines where the OSD shold appear on the screen when activated. Men Transparency sets OSD transparency between 0% (no transparency), 25%, 50% and 75%. Time Ot determines how long the OSD shold remain on screen if no bttons are pressed. Choose Always On to disable this featre. Message Box determines whether projector stats messages shold appear on the screen. OSD Settings Langage English Men Position Center Men Transparency 0 Time Ot 30 Seconds Message Box On Memory The crrent image settings can be saved as a preset, which yo can recall later. The defalt settings can be recalled at any time as well. Up to for cstom presets can be stored for each inpt. The following settings are saved in a preset: From the Image men Dynamic Black, Gamma, HDR, Brightness, Contrast, Satration, He, Sharpness and Noise Redction From the Color men Color Space, Color Mode, ColorMax, Color Temperatre, Dynamic Black, RGB Lift and RGB Gain From the Geometry men Aspect Ratio and Overscan Recall Memory Save Settings Memory Defalt Preset A Presets from one inpt cannot be applied to another inpt. To recall a saved preset: Select Recall Memory and press ENTER/OK, then select a preset from Preset A to Preset D. Select Defalt to load factory defalt vales. To save a preset: Select Save Settings and press ENTER/OK, then choose from Preset A, Preset B, Preset C and Preset D. Operating Gide page 65

74 USING THE PROJECTOR Network men DHCP, IP, Sbnet Mask, Gateway, DNS Set DHCP to On if the IP address is to be assigned by a DHCP server, or Off if it is to be set here. DHCP IP Network Off If DHCP is On, it will not be possible to edit IP Address, Sbnet Mask, Gateway or DNS. Sbnet Mask Gateway If DHCP is set to Off, edit IP Address, Sbnet Mask, Gateway and DNS as reqired. DNS MAC : 18: 27: 2d: f2: 06 MAC AMX Off This field is read-only. AMX Switch on or off. Operating Gide page 66

75 USING THE PROJECTOR PIP men PIP Trn PIP on and off. Sorce PIP Sorce Position PIP Off HDMI1 Top-Left Select an inpt sorce for the PIP image. Any combinations are possible between main and PIP inpt sorce, as long as one of the inpts is either DisplayPort or 3G-SDI. Position Set the location of the PIP image on the screen. Choose from Top-Left, Top-Right, Bottom-Left, Bottom-Right and PBP. Operating Gide page 67

76 USING THE PROJECTOR Information men This men gives information abot software and hardware configration, inpt sorce and laser operating times It also allows yo to restore the factory defalt settings. Information Model Name HIGHlite Laser 4K Serial Nmber Software Version 1 X000XXXXX0000 MD17-VD Software Version 2 STEP3_E Software Version Active / PIP Sorce HDMI 1 Signal Format Laser Hors 2 System Stats Thermal Stats Factory Reset Signal Format Active Sorce Signal Format Timing H Refresh V Refresh Pixel Clock 1080p/60Hz KHz Hz MHz PIP Sorce Timing H Refresh V Refresh Pixel Clock 576p/50Hz KHz Hz 27.0 MHz Operating Gide page 68

77 USING THE PROJECTOR Information men contined from previos page System Stats System Stats Atmospheric Pressre AC Voltage Ceiling Mode Tilt Angle Portrait Angle Altitde Mode Pa (116 m) 160V 264V 0 4 deg 0 deg Low Laser Power 100% License Key License Pass. Timeot Not Expired Thermal Stats Thermal Stats Inlet/DMD Temp. 23 / 24 (C) PW Temp. 58 (C) LD 1-6 Temp. 41 / 46 / 41 / 48 / 49 / 49 (C) Fan 1-3 Speed 1399 / 1402 / 1391 Fan 4-6 Speed 1410 / 1200 / 1205 Fan 7-9 Speed 1211 / 1407 / 1410 Fan Speed 0 / 3005 / 3007 Fan Speed 2986 / 2984 / 2984 Fan Speed 3020 / NA / NA Fan Speed 1200 / 1204 / 1200 Fan Speed 2283 / 2332 / 1800 Water Pmp Speed 2718 / 3378 / 3220 Operating Gide page 69

78 USING THE PROJECTOR Information men contined from previos page Factory Reset To restore the factory defalt settings: 1. Navigate to Factory Reset and press ENTER/OK. 2. When prompted, press ENTER/OK to confirm yor choice, or press EXIT to cancel. Software Version 2 Information Model Name E-Vision Laser 8500 Serial Nmber X000XXXXX0000 Software Version 1 MD03-SE10-FE09 Factory Reset LE07-14-RE WARNING Active Sorce HDMI All Signal ser Format settings will be lost! Laser Hors Press OK to confirm HRS System Stats Press Exit to cancel Thermal Stats Factory Reset OK Factory reset does not reset the Network settings, or High Altitde mode. Operating Gide page 70

79 SERVED WEB PAGES Served Web Pages The served web pages allow yo to control the projector remotely via LAN. The defalt IP address is Operating Gide page 71

80 SERVED WEB PAGES Operating Gide page 72

81 SERVED WEB PAGES Operating Gide page 73

82 SERVED WEB PAGES Operating Gide page 74

83 SERVED WEB PAGES Operating Gide page 75

84 SERVED WEB PAGES Operating Gide page 76

85 SERVED WEB PAGES Operating Gide page 77

86 SERVED WEB PAGES Operating Gide page 78

87 SERVED WEB PAGES Operating Gide page 79

88 This page is intentionally left blank. Operating Gide

89 HIGHlite Laser 4K Series High Brightness Digital Video Projector 4 REFERENCE GUIDE

90 IN THIS GUIDE IN THIS GUIDE Choosing A Lens Basic calclation...84 Basic calclation example...85 Fll lens calclation...86 Introdcing TRC...86 Calclating TRC...87 Calclating the throw ratio with TRC...88 LAN RS Trigger 1 & Trigger IR inpt Appendix D: Glossary Of Terms Fll lens calclation example...89 Screen Reqirements Fitting the image to the display K-UHD images displayed fll width K-UHD images displayed with a height of 2160 pixels K-UHD images displayed fll height...92 Diagonal screen sizes...93 Positioning The Image Aspect Ratios Explained Aspect ratio examples...97 Appendix A: Lens Part Nmbers Appendix B: Spported Signal Inpt Modes D formats SDI Format Appendix C: Wiring Details Signal inpts and otpts HDMI 1 and DisplayPort G-SDI In, 3G-SDI Ot Control connections Reference Gide

91 CHOOSING A LENS Choosing A Lens A nmber of lenses are available. Which lens yo choose depends on the screen size, image aspect ratio, throw distance and light otpt. The following table shows all available lenses in order of their throw ratios: Throw ratios Throw distance range 0.77 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) 1.16 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) To choose a lens, either calclate the throw ratio reqired, or se the lens charts provided in Appendix B at the end of this docment. For information abot individal lens part nmbers, see Appendix A at the end of this docment. See also Appendix B: Lens Charts at the end of this docment. Do not se the short lens hood with the : 1 zoom lens. For frther information abot sing the right lens and hood, see The lens hood in the Installation and Qick-Start Gide. Reference Gide page 83

92 Basic calclation Identify the reqired lens by calclating the throw ratio. A throw ratio is the ratio of the throw distance to the screen width: Throw distance Throw ratio = Screen width 1. Use the formla above to obtain the reqired throw ratio. 2. Match the throw ratio with a lens from the table below: CHOOSING A LENS 1 2 The basic calclation on this page does not take into consideration DMD and image size, which cold affect the throw ratio. For a more complex and realistic calclation, see Fll lens calclation in this section. Throw ratios Throw distance range 0.77 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) 1.16 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) 3. Ensre the reqired throw distance is within the range covered by the lens. 1 Screen width 2 Throw distance When calclating the throw ratio, be sre to se identical measrement nits for both the throw distance and the screen width. For information abot individal lens part nmbers, see Appendix A at the end of this docment. See also Appendix B: Lens Charts at the end of this docment. Do not se the short lens hood with the : 1 zoom lens. For frther information abot sing the right lens and hood, see The lens hood in the Installation and Qick-Start Gide. Reference Gide page 84

93 Basic calclation example CHOOSING A LENS 1. Calclate the throw ratio sing the formla. Yor screen is 4.5 m wide and yo wish to place the projector approximately 11 m from the screen. The throw ratio will then be 11 = Match the reslt with the lens table. The lens matching a throw ratio of 2.44 is the : 1 zoom lens. 3. Check whether the lens covers the reqired throw distance. The range qoted for the : 1 zoom lens is m. The reqired distance of 11 m is within the range. INFORMATION YOU NEED FOR THIS CALCULATION The throw ratio formla: Throw distance Throw ratio = Screen width The lens table: Throw ratios Throw distance range 0.77 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) 1.16 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) The basic calclation on this page does not take into consideration DMD and image size, which cold affect the throw ratio. For a more complex and realistic calclation, see Fll lens calclation in this section. For information abot individal lens part nmbers, see Appendix A at the end of this docment. Reference Gide page 85

94 CHOOSING A LENS Fll lens calclation Introdcing TRC The choice of lens will affect the image size and will address discrepancies between the DMD resoltion and the sorce. When an image fills the height of the DMD bt not the width, it ses less than 100% of the DMD srface. A lens chosen sing the basic formla may prodce an image that is considerably smaller than the actal screen. To compensate for loss of screen space in sch sitations, yo need to increase the throw ratio sing a Throw Ratio Correction (TRC). TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calclate the throw ratio sing the basic formla. Example Fig. 1 illstrates a 4:3 image within a 4K-UHD Display. Fig. 1 When a 4K-UHD projector is sed for a 4:3 image, the image does not fill the width of the DMD, creating a pillarboxing effect - blank spaces to the left and right. Fig. 2 shows the same image projected on a 4:3 screen sing a standard lens (chosen with the basic calclation). The DMD accrately fills the width of the screen; however, the pillarboxing is now part of the projected image and is transferred to the screen. The DMD does not fill the height of the screen, which has cased letterboxing - frther blank spaces at the top and bottom of the screen. The image is now srronded by blank space, which can be removed if the throw ratio is increased. Fig. 2 Fig. 3 shows the image projected on the same screen with a lens chosen sing TRC. The increased throw ratio has allowed the 4:3 image to fill the 4:3 screen seamlessly. Fig. 3 Reference Gide page 86

95 CHOOSING A LENS Calclating TRC To calclate TRC, se the following formla: TRC = 1.78 (DMD aspect ratio) Sorce aspect ratio TRC table Alternatively, yo can save time by referencing the following table, which shows the TRC vale for some poplar image formats: TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calclate the throw ratio sing the basic formla. 2.35:1 (Scope), 3840 x 1634 pixels TRC < 1, not sed 1.85:1 (Flat), 3840 x 2075 pixels TRC < 1, not sed 1.78:1 (16:9), 3840 x 2160 TRC < 1, not sed (native resoltion) 1.66:1 (Vista), 3585 x 2160 pixels TRC < 1.07, not sed 1.6:1 (16:10), 3456 x 2160 pixels TRC = 1.11, not sed 1.33:1 (4:3), 2873 x 2160 pixels TRC = :1 (5:4), 2700 x 2160 pixels TRC = 1.42 Reference Gide page 87

96 CHOOSING A LENS Calclating the throw ratio with TRC 1. For TRC > 1, amend the basic throw ratio formla as follows: Throw ratio = Throw distance Screen width x TRC 2. Once a throw ratio is established, identify the matching lens from the table: Throw ratios Throw distance range 0.77 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) 1.16 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) 3. Ensre the reqired throw distance is within the range of the matching lens. TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calclate the throw ratio sing the basic formla. Do not se the short lens hood with the : 1 zoom lens. For frther information abot sing the right lens and hood, see The lens hood in the Installation and Qick-Start Gide. Reference Gide page 88

97 Fll lens calclation example CHOOSING A LENS Yor screen is 4.5 m wide; yo wish to place the projector approximately 11 m from the screen. The sorce is 4:3. 1. Calclate TRC as follows: TRC = = Calclate the throw ratio: 11 Throw ratio = = x Find a match in the lens table. The table shows that the matching lens is the : 1 zoom lens. 4. Check whether the lens covers the reqired throw distance. The range qoted for the : 1 zoom lens is m. The reqired distance of 11 m is within the range. INFORMATION YOU NEED FOR THESE CALCULATIONS The TRC formla TRC = DMD aspect ratio Sorce aspect ratio The TRC table (to se instead of the formla) 2.35:1 (Scope) TRC not sed 1.85:1 (Flat) TRC not sed 1.78:1 (16:9) TRC not sed (native resoltion) 1.66:1 (Vista) TRC = :1 (16:10) TRC = :1 (4:3) TRC = :1 (5:4) TRC = 1.42 Throw distance The throw ratio formla Throw ratio = Screen width x TRC The lens table: Throw ratios Throw distance range 0.77 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) 1.16 : 1 fixed lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) : 1 zoom lens m ( ft) Reference Gide page 89

98 SCREEN REQUIREMENTS Screen Reqirements Fitting the image to the display If the sorce image spplied to the projector is smaller than the 4K-UHD resoltion, the image will not fill the display. The following examples show how a nmber of common formats may be displayed, depending on yor DMD resoltion. 4K-UHD images displayed fll width 2.35:1(Scope) = 1634 pixels 1.85:1 = 2075 pixels 16:9 1.78:1 (fll height) = 2160 pixels fll width = 3840 pixels Reference Gide page 90

99 SCREEN REQUIREMENTS 4K-UHD images displayed with a height of 2160 pixels fll height = 2160 pixels 4:3 = 1.33:1 = 2873 pixels 16:10 = 1.6:1 = 3456 pixels 1.66:1 (Vista) = 3585 pixels fll width = 3840 pixels Reference Gide page 91

100 SCREEN REQUIREMENTS 4K-UHD images displayed fll height fll height = 2160 pixels UXGA = 4:3 = 1.33:1 = 2873 pixels WUXGA = 16:10 = 1.6:1 = 3456 pixels Reference Gide page 92

101 SCREEN REQUIREMENTS Diagonal screen sizes Screen sizes are sometimes specified by their diagonal size (D). When dealing with large screens and projection distances at different aspect ratios, it is more convenient to measre screen width (W) and height (H). The example calclations below show how to convert diagonal sizes into width and height, at varios aspect ratios. W = width 2.35:1 (Scope) W = D x 0.92 H = D x :1 W = D x 0.88 H = D x :9 = 1.78:1 (native aspect ratio for 4K-UHD projectors) W = D x 0.87 H = D x :1 (Vista) W = D x 0.86 H = D x :10 = 1.6:1 W = D x 0.85 H = D x 0.53 H = height D = diagonal Reference Gide page 93

102 POSITIONING THE IMAGE Positioning The Image The normal position for the projector is at the centre of the screen. However, yo can set the projector above or below the centre, or to one side, and adjst the image sing the Lens shift featre (known as rising and falling front) to maintain a geometrically correct image. For more information on shifting the lens, see Lens control in the Operating Gide. Shifting the lens p (rising front) Whenever possible, position the projector so that the lens is centered for the highest qality image. Centered lens Shifting the lens down (falling front) Reference Gide page 94

103 POSITIONING THE IMAGE Any single adjstment otside the ranges specified on the following page may reslt in an nacceptable level of distortion, particlarly at the corners of the image, de to the image passing throgh the periphery of the lens optics. If the lens is to be shifted in two directions combined, the maximm range withot distortion will be somewhat less, as can be seen in the illstrations below. For more information on shifting the lens, see Lens control in the Operating Gide. Fll horizontal or vertical shift Combined shift is redced Reference Gide page 95

104 ASPECT RATIOS EXPLAINED Aspect Ratios Explained The appearance of a projected image on the screen depends on a combination of the following: The display resoltion is 4K-UHD with a 3840 x 2160 resoltion, corresponding to an aspect ratio of 16:9 The aspect ratio of the inpt signal: sally 4:3, 16:9 or 16:10 The vale of the Aspect Ratio setting of the projector: 16:9, 4:3, 16:10 and 5:4 stretch the image to the selected aspect ratio. 16:9 leaves black bars at the top and bottom of the screen (letterboxing effect); 4:3 and 5:4 leave black bars at the sides of the screen (pillarboxing). TheaterScope is a special setting sed in combination with an anamorphic lens, an optional accessory. It removes letterboxing from a 2.35:1 sorce packed into a 16:9 frame. 4:3 Narrow is a special setting sed in combination with an anamorphic lens, an optional accessory. It sqeezes 4:3 content so that the intended aspect ratio is displayed on screen when projected throgh an anamorphic lens. Sorce shows the image with its original aspect ratio, if this does not match the native aspect ratio of the DMD TM, then the image will be scaled to either fit the fll width or height of the display. Reference Gide page 96

105 Aspect ratio examples ASPECT RATIOS EXPLAINED Sorce: 4:3 1 1 Aspect Ratio: Sorce / 4:3 Aspect Ratio: 16:10 Sorce: 16:9 1 1 Aspect Ratio: Sorce / 16:9 Aspect Ratio: 16:10 Sorce: 16:10 (native) 1 Unsed screen areas Aspect Ratio: Sorce / 16:10 Reference Gide page 97

106 ASPECT RATIOS EXPLAINED Aspect ratio example: TheaterScope The TheaterScope setting is sed in combination with an anamorphic lens to restore 2.35:1 images packed into a 16:9 frame. Sch images are projected with black lines at the top and bottom of the 16:9 screen to make p for the difference in aspect ratios. Withot an anamorphic lens and withot the TheaterScope setting applied, a 16:9 sorce containing a 2.35:1 image looks like this: Black margin part of the sorce Black margin part of the sorce If we change the setting to TheaterScope, the black lines will disappear bt the image will stretch vertically to reach the top and bottom of the DMD : An anamorphic lens will stretch the image horizontally, restoring the original 2.35 ratio: Reference Gide page 98

107 APPENDIX A: LENS PART NUMBERS Appendix A: Lens Part Nmbers Throw ratios Part nmber Throw distance range Lens extension 0.77 : 1 fixed lens m ( ft) mm : 1 zoom lens m ( ft) mm 1.16 : 1 fixed lens m ( ft) mm : 1 zoom lens m ( ft) mm : 1 zoom lens m ( ft) 73.7 mm : 1 zoom lens m ( ft) 80.6 mm : 1 zoom lens m ( ft) 72.6 mm : 1 zoom lens m ( ft) 83.3 mm The throw ratios given here apply only when the image fills the width of the DMD. For images that do not fill the width of the DMD, the throw ratio needs to be recalclated sing a throw ratio correction (TRC). For frther information, see Choosing A Lens and Appendix B: Lens Charts. Throw distance calclations are based on the distance from the oter end of the lens, which will vary from lens to lens. Do not se the short lens hood with the : 1 zoom lens. For frther information abot sing the right lens and hood, see The lens hood in the Installation and Qick-Start Gide. Reference Gide page 99

108 APPENDIX B: SUPPORTED SIGNAL INPUT MODES Appendix B: Spported Signal Inpt Modes 2D formats Signal Format Resoltion Frame Rate (Hz) DisplayPort / DVI-D HDMI / HD-BaseT RGB YUV 8-bit YUV 10-bit YUV 12-bit Otpt Frame Rate (Hz) Remarks PC 640x X X x X X x X X x X X x X X x X X x X X x X X * X X * X X * X X x X X x X X x X X x X X x X X x X X x X X x1200 RB 50 X X x1200 RB 60 X X X X X x X X 60 Reference Gide page 100

109 APPENDIX B: SUPPORTED SIGNAL INPUT MODES Signal Format Resoltion Frame Rate (Hz) DisplayPort / DVI-D HDMI / HD-BaseT RGB YUV 8-bit YUV 10-bit YUV 12-bit Otpt Frame Rate (Hz) Remarks PC 1440 x X X 60 (contined) 1280 x X X x X X x X X 60 Apple Mac 640x X X x X X 60 SDTV 480i x480i 60 X X X X x576i 50 X X X X i EDTV 480p X X X X X p 50 X X X X X 50 HDTV 1035i 60 X X X X X i 50 X X X X X i X X X X X i 60 X X X X X p 50 X X X X X p X X X X X p 60 X X X X X p X X X X X p 24 X X X X X p 25 X X X X X p X X X X X p 30 X X X X X p 50 X X X X X 50 Reference Gide page 101

110 APPENDIX B: SUPPORTED SIGNAL INPUT MODES Signal Format Resoltion Frame Rate (Hz) DisplayPort / DVI-D HDMI / HD-BaseT RGB YUV 8-bit YUV 10-bit YUV 12-bit Otpt Frame Rate (Hz) Remarks HDTV (contined) SDI Format Timing 1080p X X X X X p 60 X X X X X 60 2K (2048x1080) 24/25/30/50/60 X X X X X 48/50/60/50/60 4K-UHD 24/25/30 X X X X*1 X*1 48/50/60 *1 4K-UHD 50/60 X X (8 bits) X*2 X*3 X*3 50/60 *2, *3 SDI Link mode Signal Standards NTSC SD SMPTE 259M-C 270Mbps SD YCbCr 4:2:2 10 PAL SD SMPTE 259M-C 270Mbps SD YCbCr 4:2: i60 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: i59 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: i60 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: P30 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: P25 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: i50 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: P24 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: P60 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: P50 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: Sf25 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: Sf30 HD SMPTE 292M 1.5Gbps HD YCbCr 4:2: P50 3G Level A SMPTE 424M 3Gbps YCbCr 4:2:2 10 Color Encode Sampling Strctre Bit Depth Remarks: *1 HDBaseT spports 4K 24/25/30Hz 4:2:2 only *2 HDBaseT spports 4K 50/60Hz 4:2:0 only *3 HDMI 1,2 spport p to 4:2:2, HDBaseT does not spport Reference Gide page 102

111 APPENDIX B: SUPPORTED SIGNAL INPUT MODES Timing SDI Link mode Signal Standards Color Encode Sampling Strctre Bit Depth 1080P59 3G Level A SMPTE 424M 3Gbps YCbCr 4:2: P60 3G Level A SMPTE 424M 3Gbps YCbCr 4:2: P50 3G Level B SMPTE 424M 3Gbps YCbCr 4:2: P59 3G Level B SMPTE 424M 3Gbps YCbCr 4:2: P60 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:2 10 Reference Gide page 103

112 APPENDIX C: WIRING DETAILS Appendix C: Wiring Details Signal inpts and otpts HDMI 1 and 2 19 way type A connector 1 TMDS Data 2+ 2 TMDS Data 2 Shield 3 TMDS Data 2-4 TMDS Data 1+ 5 TMDS Data 1 Shield 6 TMDS Data 1-7 TMDS Data 0+ 8 TMDS Data 0 Shield 9 TMDS Data 0-10 TMDS Clock+ 11 TMDS Clock Shield 12 TMDS Clock- 13 CEC 14 not connected 15 SCL (DDC Clock) 16 SCA (DDC Data) 17 DDC/CEC Grond V Power 19 Hot Plg Detect HDMI: pin view of panel connector Reference Gide page 104

113 APPENDIX C: WIRING DETAILS DisplayPort DisplayPort Pin 1 ML_Lane 0 (p) Lane 0 (positive) Pin 2 GND Grond Pin 3 ML_Lane 0 (n) Lane 0 (negative) Pin 4 ML_Lane 1 (p) Lane 1 (positive) Pin 5 GND Grond Pin 6 ML_Lane 1 (n) Lane 1 (negative) Pin 7 ML_Lane 2 (p) Lane 2 (positive) Pin 8 GND Grond Pin 9 ML_Lane 2 (n) Lane 2 (negative) Pin 10 ML_Lane 3 (p) Lane 3 (positive) Pin 11 GND Grond Pin 12 ML_Lane 3 (n) Lane 3 (negative) Pin 13 CONFIG1 connected to Grond1) Pin 14 CONFIG2 connected to Grond1) Pin 15 AUX CH (p) Axiliary Channel (positive) Pin 16 GND Grond Pin 17 AUX CH (n) Axiliary Channel (negative) Pin 18 Hot Plg Hot Plg Detect Pin 19 Retrn Retrn for Power Pin 20 DP_PWR Power for connector (3.3 V 500 ma) DisplayPort: pin view of panel connector Reference Gide page 105

114 APPENDIX C: WIRING DETAILS 3G-SDI In, 3G-SDI Ot 75 ohm BNC 3G-SDI connector 3G-SDI signals are very high speed digital signals which reqire better qality coaxial cable than conventional analoge video. The data rate is 3 Gigabits per second. In choosing cable length and connectors for any installation the freqency response loss in decibels shold be proportional to f, from 1 MHz, to 3 GHz. HDBaseT inpt RJ45 socket. HDBaseT inpt Reference Gide page 106

115 APPENDIX C: WIRING DETAILS Control connections LAN RJ45 socket (Shared with HDBaseT) Only one remote connection (RS232 or LAN) shold be sed at any one time. HDBaseT/LAN port RS232 9 way D-type connector 1 nsed 2 Received Data (RX) 3 Transmitted Data (TX) 4 nsed 5 Signal Grond 6 nsed 7 nsed 8 nsed 9 nsed RS232: pin view of female connector Reference Gide page 107

116 APPENDIX C: WIRING DETAILS Trigger 1 & Trigger mm mini jack Tip Sleeve Tip Signal Sleeve Grond Otpt: 12V, 200 ma max IR inpt 3.5 mm mini jack Tip Signal Ring Not connected Sleeve Grond Tip Ring Sleeve Reference Gide page 108