Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters

Size: px
Start display at page:

Download "Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters"

Transcription

1 Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters Written By: Colin Langridge Issue: Draft Date: 03 rd July Date: 29 th July Date: 20 th August Date: 02 nd September 2008 Page 1 of 26

2 Installation Instructions The Autoread camera system is designed to replace the standard OMR section from a collate unit on the inserter. The instructions are intended as a general guide to help with initial setup and running the system. The detailed manual from Lake Image System (LIS) is included with the inserter documentation. There is a new supplement dedicated to OMR setup The above view shows the basic layout of the autoread camera system The camera system is set to a fixed height. The camera lens needs to be focused and the locking screws fitted prior to running the camera system Page 2 of 26

3 Autoread Camera fitted in the inserter. View showing 1 of the fixed LED light sources. Whole top assembly pivots as shown to allow for access to the OMR section if required View showing the Autoread camera in the inserter. The operator replaceable camera bracket is shown here as well as the disposable camera cables. (Swapping of the camera is required for some high-density 2D labels) Page 3 of 26

4 Cable Routing and Electrical Installation The Autoread input reader requires a separate dedicated PC to decode the image. This PC is located under a downstream feeder on the inserter. The PC is located in a secure enclosure to prevent tampering with the cables / connections. (A separate keyboard / mouse is attached to the PC to allow the camera to be installed) Once the camera system has been installed and setup by an engineer to work with the inserter, then there is no need to make any adjustments or change any settings. New jobs will need to be setup by a trained operator / engineer The camera PC boots directly to the camera application. The inserter selects the desired job, sets the trigger delay and moves the camera to the correct position for each job. The camera system utilises the standard OMR PCB ( ). The camera has a separate interface PCB ( ) that connects to J1 on the OMR PCB. All cables route back to the LIS PC through the collate unit. PC enclosure containing the LIS PC. (shown situated under a feeder.) All camera cables wire back to the rear of the LIS PC as shown The two short cables form the camera wire into the connectors as shown. These then wire back to the LIS PC through the collate unit. The Two short cables from the camera are designed to be replaceable (If required) Always ensure the power is OFF on the LIS PC before replacing the cables from the camera Page 4 of 26

5 The camera system has three fixed light sources. These LED light sources ensure that the entire FOV is well lit and the light is very uniform. The three light sources wire back to a distribution box situated in the bottom of the collate unit. A single cable then wires back to the LCU card in the LIS PC. Three light sources in position Light sources shown for the autoread camera system. Each light source contains 72 hipower white LED. These are triggered by the inserter and controlled (current & on time) by the LIS hardware Trigger from the hi-cap exit sensor. Ribbon cable picks up the signal and sends it to the camera PCB. This means the camera is triggered by the LE of the document, this gives an accurate and consistent trigger point. The trigger delay (made up from the fixed offset and the variable delay) is then applied using tacho pulses to ensure the camera system triggers at the correct point in time Page 5 of 26

6 Camera System Connections Explanation CAMERA PCB Cable to LIS PC ( ) Trigger in from the exit sensor on the hi-cap feeder Link cable between OMR PCB & Camera PCB ( ) OMR PCB ( ) Standard serial COMS cables to inserter control PCB Note no software trigger required for this setup. Link between OMR PCB and Collate module PCB NOT required. Switch on Camera PCB must be set to SENSOR Position Description 1 A B COMMS Port 6 Port 5 Not used Not used 2 C D COMMS Port 4 Port 3 Not used To inserter 3 E F SCM Links to Inserter Sensors cable 4 G H F/wire To camera Not used 5 LCU I To LED lights J To camera cable 1 Page 6 of 26

7 Camera cable 2 Camera cable 1 To light distribution box To Camera PCB Cable Rear view showing all connections from the LIS PC This COM port (1) is used to communicate with the inserter PC. The supplied serial cable is wired between here and an USB to serial adaptor on the inserter PC LIS PC graphics out port. This is connected to port A on the VDU switch box. Page 7 of 26

8 Rear view of LIS camera PC. Showing all cables connected. LIS supplied camera cable The LIS PC is powered from the electrical panel in unit 0. This is where the inserter PC is powered. The electrical panel remains Live when the main power switch for the inserter is turned off. This allows for either PC to be used when the inserter is off. Inserter monitor powered from here LIS PC powered from here Inserter PC powered from here Mains IN to the electronics panel Electronics Panel on Unit zero of the inserter Page 8 of 26

9 Hardware Installation of the Autoread Camera on the Inserter To use the Autoread head (camera) it needs to be selected in the hardware setup of the inserter application as shown below: Once the autoread camera is selected in the hardware then the COM port needs to be setup. Navigate to the external devices screen and select the desired COM port for the Autoread Head. The COM port number should be the same as the COM port number assigned to the USB to serial adaptor when it was installed. NOTE: Once selected in hardware and the external device port number is set it is recommended that he application is closed and re-started to ensure all the settings are initialised correctly. Page 9 of 26

10 Setting up Communication Ports The inserter communicates via its PC to the LIS PC. The port needs to be configured within the Inserter and Windows. Follow the provided instructions to install the hardware (USB to Serial Adaptor). To set up the USB to serial adaptor navigate to: Control Panel System Hardware Device Manager Ports (Com & LPT) right click for Properties. Please ensure that the settings for the comm. Port are as follows: COM port settings Baud Rate Parity NONE Data Bits 8 Stop Bits 1 Flow Control NONE The COM port number defined within the inserter application can vary, just ensure that the settings are correct and that the com port number defined within the application is the same as the com port number assigned to that USB to serial adaptor The COM port number of the USB to serial adaptor can be changed to any unused port number if required. (Select advanced options and select an unused port number from the list) COM PORT NUMBERS SHOWN ARE FOR ILLUSTRATION ONLY The LIS PC always uses com. port 1 for communications with the inserter. Page 10 of 26

11 LIS Camera Monitor and Dual Display The LIS camera PC utilizes the inserters second display. This second display is used to display the camera application Multicam. The second monitor can also be used to display the inserters run screen. The second display is set to clone the inserter display. (This can be very useful if fitted to an inserter with a large number of units as the run screen can be seen from the far end of the inserter (also allows for the run screen to be seen from various viewing angles)) A manual switch box is used to swap between the two inputs on the second display. The switch box is mounted underneath the divert / collate unit on the prime station (directly next to the second display) The connections for the switch box are as follows 1 I/O goes to the 2 nd Monitor 2 B Goes to one of the outputs from the dual VGA cable on the Inserter PC 3 A Goes to LIS PC VGA graphics port Page 11 of 26

12 Rear view of the switch box Front view of the switch box Note. Always ensure that the switch box is set to the main inserter display when the inserter PC is powered on. Otherwise the second display may not be detected The video signal from the inserter PC is split so that it can be used on a dual display setup. This is achieved by using the following cable This cable plugs into the graphics card output and provides 2-off VGA outputs. This is used to send the signal to two analogue displays. All new inserters are fitted with this cable as standard. VGA splitter cable Simple Block Diagram showing the Dual display connections / cable routings MAIN INSERTER DISPLAY VGA SPLTTER CABLE INSERTER PC Mains Panel B SWITCH BOX A LIS CAMERA PC I/O Mains SECOND DISPLAY Page 12 of 26

13 Clone Display Instructions To display the inserter PC display (run screen) it is necessary to setup the second display and then set it to clone the main display. To do this following these instructions: Right click on the desktop and select Properties Navigate to the Settings tab and select the advanced. This will display the monitor setup screen. Select the Catalyst control center tab and run the application (the application may vary due to the manufacturer of the graphics display card fitted to the inserter PC but the basic principles are common) Select the BASIC option and select Next to proceed The following screen is then shown. Select Go and proceed to the next screen Page 13 of 26

14 The following screen is now supplied. This shows the monitors that are currently available. Only the main display is currently active Select the second display as shown. Then press Next to proceed The following screen is now displayed. Select the Clone option. This will copy the display from the main monitor onto the second display monitor. Press Next to proceed. Select YES when prompted to accept the changes Page 14 of 26

15 The following screen is now displayed. Select Finish to proceed. Both displays should now be able to show the inserter run screen. After completing all of the steps above. It may be necessary to select a different screen display resolution. Right click on the desktop select Properties. Then select the Settings tab. Select the desired display (1 or 2) the adjust the screen resolution as required (the inserter application is designed to be used on a display set to a resolution of 1024 x 768) select apply when finished Clone Display Warning For correct functionality on power up you must ensure that the switch box is set to B (inserter) to make sure the dual display works correctly and the display is cloned Picture showing the inserter run screen on the second display Page 15 of 26

16 Passwords and Access For all set up, the engineer must log in as an administrator. This gives full access to all the functions required to set the camera systems up. (The Administrator Password If not known can be obtained from AM5Support Setting Correct Output Fonts This is set before the system leaves the factory. The output font required is Automailer. A carriage return and line feed follow each camera read. The advance settings determine what is sent by the camera to the inserter when a no read or a misread occurs, in both instances this should be?? Page 16 of 26

17 Engineer Initial Set Up The application Multicamsetup is used to setup the autoread camera. These settings are factory set and should only be adjusted by a trained engineer. The following screen dumps show the most important settings and can be used for future reference These are the settings for the SCM card in the LIS PC These are the settings for the high resolution camera. They setup the frame grabber output, the camera type/orientation. The conversion factor for pulses to mm is set to one, (this is unique for LIS camera units and different from other readers, which use 4 pulses/mm) the mode is encoder, the trigger polarity is rise and the trigger input line is set to one Page 17 of 26

18 Advanced settings for the camera are shown below. Format is the output font (this is explained in a previous section of the documentation) The output comms are the settings used to send the camera read data to the inserter. Format Automailer Port 3 Baud Rate Parity Even Data Bits 7 Stop Bits 1 Input comms settings Port 1 Baud Rate Parity None Data Bits 8 Stop Bits 1 The input comms are the settings used to communicate with the inserter PC. The LIS PC always uses com port 1. The Function LIS Remote Control defines the protocol for the communication between the inserter PC and the LIS PC Page 18 of 26

19 Multicam Run Screen Navigation Below is an example of a typical Multicam run screen. The Field of view (FOV) is shown in the top right hand corner. The region of interest (ROI) is shown by the blue box around the OMR marks. Start/Stop This turns the camera reading on/off for the mode that is running Ending current mode / Changing to a new mode Select End to stop the current mode. The inserter selects the new modes automatically. When the setup data (trigger delay etc) is sent to the LIS camera PC Serial data sent to the inserter The log table displays the data sent via the serial port to the inserter Display Window This shows the documents as they pass under the camera, the image updates each time there is a trigger. The display window (FOV) is a useful tool as it allows the operator to see the last read (Bad read action for a collate must be Stop in Collate ) this stops the error document as soon as possible and the display window will show the last/error doc. From this display you can see the OMR marks relative to the AOI and adjust the trigger delay if necessary or make adjustments to the AOI, if necessary to compensate for print movement Trigger Delay Adjustment This is used to move the OMR marks to the centre of the AOI. If the Paper travel is from right to left on the screen then increasing the trigger delay will move the OMR marks to the left and decreasing the trigger delay will move the OMR marks to the right. If no image is found get an engineer to check the correct offset is set for the feed unit and the conversion for pulses to mm is correct. Page 19 of 26

20 Diagnostics for an Engineer The application Step Counter Module (SCM) Diagnostic allows the engineer to test the camera set up to ensure the encoder, trigger and communications works correctly Serial Port This configures the serial communication between the serial card and the software. Default port is 5. Dual Input camera system also uses port serial port 6 for the second camera Outputs 1-8 This monitors the output from each trigger. (Normally output 1 for camera one and output 2 for camera two) Clear Errors This is used to reset any errors. Accuracy, Reverse and Comms are highlighted with green. This indicates no problems exist. If a fault does exist, the fault status color will change to red. See Manual for an example if required Check Errors Displays a message at the bottom of the screen and/or one of the green highlights changes to red. Count Counts the encoder pulses for each trigger output. Read Frequency Displays the number of pulses per 0.1 second. This is used to determine rpm s of the encoder. Read Outputs Activates all the trigger outputs Test Settings Turns the outputs ON Version Detects the SCM firmware version. Page 20 of 26

21 Operator Instructions for using OMR with an Autoread Camera The OMR marks need to be setup (functions defined to each mark) as per normal using the OMR setup screen in the inserter application. The camera system only sends the marks (ones and zeros) to the inserter. The decoding of the marks is performed by the inserter firmware. The OMR marks should always be programmed from the Gate mark onwards (i.e. the gate mark will always be in position one for any mark set. The mark direction field has no functionality (as the direction of the read (position of the Gate mark) is defined in the multicam application) The first mark position field is not required as the position of the OMR marks on the page are defined when setting up the document. The figures used are converted into the trigger delay (to ensure the OMR marks are in the centre of the FOV and in the ROI) The defined OMR mark set needs to be assigned to the document. The positional coordinates of the OMR marks are then defined. The X and Y values are used to determine the position of the OMR marks on the document. The dimensions are in mm and start from the datum point, which is always the top left hand corner of the document. For a vertical set of OMR marks: Value X is measured from the top left hand corner of the document across the page to the centre of an OMR mark. (This value is used to position the camera) The Y value is measured from the to top left hand corner of the document down the page to the middle OMR mark set (Example Total OMR marks is 9 so measure down the to the 5 th mark)(this value is used with the fixed offset to calculate the trigger delay) Similar principle is applied if the OMR mark set is horizontal. Page 21 of 26

22 Configuration Settings The Mark Reading mode is OMR Marks (CAMERA) It is recommended (at least for setup) that the Bad Read Groups action is set to stop in collate. This ensures that if an error occurs, the image displayed on the Multicam run screen is of the error document. This makes the process of determining why the error occurred possible (able to see if the ROI, the trigger and the printing are correct) The camera job name defined in the inserter config screen must be the same as the mode/job name defined in the Multicam application for the OMR mark set / document to be read. This allows the inserter to automatically select the correct camera mode/job for the job run. The Autoread Head camera num should always be 1 if only one camera is installed. Page 22 of 26

23 Operator Instructions for Multicam (LIS PC Application) The following instructions explain how to setup the LIS camera system (multicam) to read OMR. The existing documentation for setting up LIS cameras for input and output reading explain how to setup for barcode (2D) and OCR reading Please refer to the LIS supplied documentation for more information on setting up multicam to read OMR, Barcode (2D) and OCR This shows the main run screen of the multicam application To set up a new job/mode follow these instructions. Stop any active mode and select End. This will terminate the current job. Select new and name the job/mode as desired. Then from the run screen select Setup Then define a new area selecting the required tool (for Optical Mark Reading it is OMR). Once defined the area needs to be setup for the OMR marks. Page 23 of 26

24 Select modify and a new screen is displayed showing the settings for the selected area. Make sure a document is under the camera when completing this part of the setup. Either manually place a document under the camera in the reading section or use load to reader function. (To do this you must have completed the LIS setup as far as this point and gone back to the main run screen of multicam. So that the inserter can select the correct mode (This also means that the config of the inserter must be complete) the inserter will load a document from the feeder under the camera and position the camera based on the X co-ordinate programmed for the current document) The Read direction must be set first. This sets the position of the Gate mark in the OMR set. The direction is defined as the direction of travel. If East is selected then in the example shown the Gate is on the far left hand side and the marks travel towards the right (EAST) Next we calibrate the system. To achieve this at least two marks are required. (We recommend using at least 4 successive marks, although it is possible to use less marks and them not to be successive) Calibration Technique Using the mouse draw a narrow ROI over the marks. Then enter the number of marks displayed using 1 and 0. For our example it should be Then set the length to 4 and select Learn Pitch. This will calculate the mark pitch. Then set the length to the total number of marks (17 in our example) Delete the displayed marks (this is only used for learning the pitch) Select Live image and then select Read Mark (the read will be incorrect as the correct full size ROI has not been defined) Page 24 of 26

25 Again use the mouse to draw a ROI around all of the OMR marks (make sure this covers the entire mark set. The read will then become correct. The ROI can be bigger than the mark set to allow for print movement etc. but there are limits to its size in the FOV ROI in the FOV Setting final ROI based on the OMR marks size (approx times bigger than the marks) It depends on the mark size and the mark thickness / density as the OMR read is based on a contrast between the marks and the background. If the ROI is too big compared to the size of the OMR marks then you will get partial (wrong) reads (see below) The system can cope with some of the OMR marks not being in the ROI as the example shows above Always select read marks before leaving the setup screen to ensure that the marks in the ROI can be statically read Page 25 of 26

26 How to Adjust the ROI and trigger position in a job run During a job run it may be necessary to adjust the ROI or the trigger delay due to print movement of the OMR marks Trigger delay here is incorrect for the particular print run (marks are in a different position on the page since the original job was setup) Adjust the trigger delay on the screen (units are in mm) Increasing the trigger delay will move the OMR marks to the right and decreasing the trigger delay will move the marks to the left. Trigger delay has been adjusted to move the OMR marks into the ROI. (Trigger delay was decreased so the image was captured earlier (moved the OMR marks to the left) If the trigger delay is altered in a job run the changes are not saved. Next time the job is run from scratch the trigger delay will be sent from the inserter to the camera (based on the coordinates programmed for the Y dimension in document setup) Print movement may occur in the X direction. This is corrected by stopping the job and going to setup. Then select modify. Use the mouse to drag the ROI to the desired location around the OMR marks. Select read marks to check the setting before exiting. (DO not select LIVE VIEW, as this will loose the image on the screen) Return to the RUN screen and start the job If modifications made to ROI or trigger delay during a run, then the job/mode may need to be manually started before running the inserter again (check the status is running and the box is green) Page 26 of 26

Three Axis Digital Readout System

Three Axis Digital Readout System NEWALL MEASUREMENT SYSTEMS C80 Three Axis Digital Readout System CONTENTS 2 SPECIFICATIONS 3 CONNECTIONS 4 MOUNTING 4 Arm Mounting (Non-adjustable) 4 Arm Mounting (Adjustable) 5 Face Mounting (Adjustable)

More information

VIDEO GRABBER. DisplayPort. User Manual

VIDEO GRABBER. DisplayPort. User Manual VIDEO GRABBER DisplayPort User Manual Version Date Description Author 1.0 2016.03.02 New document MM 1.1 2016.11.02 Revised to match 1.5 device firmware version MM 1.2 2019.11.28 Drawings changes MM 2

More information

ivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1.

ivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1. MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Rev. 1.01 Page i Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice

More information

Table of Contents. Versa TILE & Versa DRIVE D2 Quick Start Manual

Table of Contents. Versa TILE & Versa DRIVE D2 Quick Start Manual Versa TILE & Versa DRIVE D2 Table of Contents 1. Introduction 2 2. Versa TILE Assembly & Cabling 2 3. Computer & Versa DRIVE Connections 2 4. RasterMAPPER 3 5. Buffer Board 4 6. Testing the System 5 7.

More information

ivw-fd133 Video Wall Controller MODEL: ivw-fd133 Video Wall Controller Supports 3 x 3 and 2 x 2 Video Wall Array User Manual Page i Rev. 1.

ivw-fd133 Video Wall Controller MODEL: ivw-fd133 Video Wall Controller Supports 3 x 3 and 2 x 2 Video Wall Array User Manual Page i Rev. 1. MODEL: ivw-fd133 Video Wall Controller Supports 3 x 3 and 2 x 2 Video Wall Array User Manual Rev. 1.01 Page i Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior

More information

Field Service Procedure Replacement PCU Kit, Coastal

Field Service Procedure Replacement PCU Kit, Coastal 1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the PCU assembly on the coastal series antennas. 2. Checklist: Initialization Rate Sensor Outputs Run the Built In Test

More information

INSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM

INSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM INSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM ATTENTION: READ THE ENTIRE INSTRUCTION SHEET BEFORE STARTING THE INSTALLATION PROCESS. WARNING! Do not begin to install your

More information

LedSet User s Manual V Official website: 1 /

LedSet User s Manual V Official website:   1 / LedSet User s Manual V2.6.1 1 / 42 20171123 Contents 1. Interface... 3 1.1. Option Menu... 4 1.1.1. Screen Configuration... 4 1.1.1.1. Instruction to Sender/ Receiver/ Display Connection... 4 1.1.1.2.

More information

Transmitter Interface Program

Transmitter Interface Program Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following

More information

with the Field-IQ Crop Input Control System

with the Field-IQ Crop Input Control System with the Field-IQ Crop Input Control System Quick Reference Card CONNECTING THE SYSTEM Ag25 GNSS antenna (P/N 68040-OOS) TNC/TNC right-angle cable (P/N 50449) Cable assembly, display to Field-IQ (P/N 50449)

More information

Auxiliary states devices

Auxiliary states devices 22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary

More information

Introduction Display...1 Mounting...1 Firmware Version...2. ADL Operation... 3

Introduction Display...1 Mounting...1 Firmware Version...2. ADL Operation... 3 MoTeC MDD User Manual Contents Introduction... 1 Display...1 Mounting...1 Firmware Version...2 ADL Operation... 3 1. Full ADL Display...4 2. Gain Loss Layout for ADL...6 3. Large Numeric Layout for ADL...8

More information

Intelligent Security and Fire Ltd

Intelligent Security and Fire Ltd User Manual Product ranges covered by this manual Vi-P14 Vi-P14A Document Reference Date Firmware Vi-Q4C1 Viq601a.doc 26/11/2009 From Viq001a21 Videoswitch Telephone 01252-851510 Ocean House, Redfields

More information

Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door

Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the

More information

CCE900-IP-TR. User s Guide

CCE900-IP-TR. User s Guide CCE900-IP-TR CCE900-IP-T & CCE900-IP-R User s Guide i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com 1. Introduction The CCE900-IP-T & CCE900-IP-R is a solution

More information

DRAFT RELEASE FOR BETA EVALUATION ONLY

DRAFT RELEASE FOR BETA EVALUATION ONLY IPM-16 In-Picture Audio Metering User Manual DRAFT RELEASE FOR BETA EVALUATION ONLY Ver 0.2 April 2013 1 Contents Introduction...3 In Picture Audio Meter Displays...4 Installation...7 External Audio Board

More information

D-Lab & D-Lab Control Plan. Measure. Analyse. User Manual

D-Lab & D-Lab Control Plan. Measure. Analyse. User Manual D-Lab & D-Lab Control Plan. Measure. Analyse User Manual Valid for D-Lab Versions 2.0 and 2.1 September 2011 Contents Contents 1 Initial Steps... 6 1.1 Scope of Supply... 6 1.1.1 Optional Upgrades... 6

More information

ivw-ud322 / ivw-ud322f

ivw-ud322 / ivw-ud322f ivw-ud322 / ivw-ud322f Video Wall Controller Supports 2 x 2, 2 x 1, 3 x 1, 1 x 3, 4 x 1 & 1 x 4 Video Wall Array User Manual Rev. 1.01 i Notice Thank you for choosing inds products! This user manual provides

More information

INSTALATION AND OPERATION MANUAL ABYSSAL OS Overlay Module Version 1.0.1

INSTALATION AND OPERATION MANUAL ABYSSAL OS Overlay Module Version 1.0.1 INSTALATION AND OPERATION MANUAL ABYSSAL OS Overlay Module Version 1.0.1 Thank you for purchasing the Abyssal OS Overlay Module for your ROV. This instruction manual contains all the information you ll

More information

EDL8 Race Dash Manual Engine Management Systems

EDL8 Race Dash Manual Engine Management Systems Engine Management Systems EDL8 Race Dash Manual Engine Management Systems Page 1 EDL8 Race Dash Page 2 EMS Computers Pty Ltd Unit 9 / 171 Power St Glendenning NSW, 2761 Australia Phone.: +612 9675 1414

More information

TeamWork Kits Installation Guide

TeamWork Kits Installation Guide TX 0 RX COM +5V APARATUS US TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher, system controller, Cable Cubby, and cables

More information

GWL/ Power Group Technology Solutions Stay Powered for the Future

GWL/ Power Group Technology Solutions Stay Powered for the Future GWL/ Power Group Technology Solutions Stay Powered for the Future BMS2405 CONNECTION GUIDE: This is simple step-by-step manual how to CONNECT AND proceed basic SETUP of BMS2405. In following example connection

More information

ORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual

ORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual ORM0022 EHPC210 Universal Controller Operation Manual Revision 1 EHPC210 Universal Controller Operation Manual Associated Documentation... 4 Electrical Interface... 4 Power Supply... 4 Solenoid Outputs...

More information

EEG A1452 SCTE-104 Inserter Frame Card

EEG A1452 SCTE-104 Inserter Frame Card EEG A1452 SCTE-104 Inserter Frame Card Product Manual EEG Enterprises, Inc. 586 Main Street Farmingdale, New York 11735 TEL: (516) 293-7472 FAX: (516) 293-7417 Copyright EEG Enterprises, Inc. 2017 All

More information

VBOX 3i Dual Antenna RTK

VBOX 3i Dual Antenna RTK The VBOX 3i RTK, RACELOGIC s most powerful GPS data logging system, is an RTK enabled version of the VBOX 3i Dual Antenna which can be used in conjunction with an RTK differential Base Station to obtain

More information

Re:source. Communication Module. SAT Version. Dominating Entertainment. Revox of Switzerland. E2.00

Re:source. Communication Module. SAT Version. Dominating Entertainment. Revox of Switzerland. E2.00 Re:source Communication Module SAT Version Dominating Entertainment. Revox of Switzerland. E2.00 Please note: Software update! Unlike the software for the Standard communication module, the SAT control

More information

R5 RIC Quickstart R5 RIC. R5 RIC Quickstart. Saab TransponderTech AB. Appendices. Project designation. Document title. Page 1 (25)

R5 RIC Quickstart R5 RIC. R5 RIC Quickstart. Saab TransponderTech AB. Appendices. Project designation. Document title. Page 1 (25) Appendices 1 (25) Project designation R5 RIC Document title CONTENTS 2 (25) 1 References... 4 2 Dimensions... 5 3 Connectors... 6 3.1 Power input... 6 3.2 Video I... 6 3.3 Video Q... 6 3.4 Sync... 6 3.5

More information

RF Mogul. Quick Start. Model: SDC1. Satellite Dish Controller

RF Mogul. Quick Start. Model: SDC1. Satellite Dish Controller RF Mogul Satellite Dish Controller Model: SDC1 Quick Start 29 February 2012 Minimum required hardware to find a Satellite! This Quick Start document is for connecting and operating a General Dynamics C125M

More information

Quick Operation Guide of LTN7700/7600 Series NVR

Quick Operation Guide of LTN7700/7600 Series NVR Quick Operation Guide of LTN7700/7600 Series NVR UD.6L0202B0042A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable

More information

DX-10 tm Digital Interface User s Guide

DX-10 tm Digital Interface User s Guide DX-10 tm Digital Interface User s Guide GPIO Communications Revision B Copyright Component Engineering, All Rights Reserved Table of Contents Foreword... 2 Introduction... 3 What s in the Box... 3 What

More information

Personal Information Page

Personal Information Page Rev. 08.29.07 Personal Information Page Installing Dealer Name Date of Installation Day Month Year Type of System Executive MD500 MD1000.2 MHDTV MD5Slim MSD60 Freedom (not recommended) Serial Number of

More information

Single Axis Position Controller

Single Axis Position Controller SERIES P9511 Single Axis Position Controller Compact Construction Simple Go-to operation Integrated Relay Output Integrated Mains Power Supply ELEKTRO-TRADING sp. Z o.o. 44-109 Gliwice, ul. Mechaników

More information

VBOX3i Dual Antenna. Measures Slip and Pitch/Roll (RLVB3iSL) Features

VBOX3i Dual Antenna. Measures Slip and Pitch/Roll (RLVB3iSL) Features VBOX3i dual antenna (VB3iSL) is Racelogic s most powerful GPS data logging system. By utilising two GPS engines configured in a Fixed Baseline RTK setup, the VB3iSL combines high level accuracy and test

More information

Revision Protocol Date Author Company Description January Paul DOS REMEDIO S. Imagine Communications

Revision Protocol Date Author Company Description January Paul DOS REMEDIO S. Imagine Communications PRODUCT ADC TOPIC ODETICS TCS-90 CART MACHINE DATE: January 25, 2001 REVISION HISTORY Revision Protocol Date Author Company Description 1.1 25 January 2001 Paul DOS REMEDIO S Imagine Communications New

More information

Ford 6.4L Powerstroke Installation Instructions

Ford 6.4L Powerstroke Installation Instructions 31 December 2008 BD Ford 6.4L Powerstroke X-Tuner # 1054871 1 ULTRA X-TUNER POWER PROGRAMMER Ford 6.4L Powerstroke Installation Instructions 1054871 Ford 6.4L Powerstroke F250 / F350 / F450 2008+ *** READ

More information

P-2 Installing the monitor (continued) Carry out as necessary

P-2 Installing the monitor (continued) Carry out as necessary P-2 Installing the monitor (continued) Carry out as necessary Using the monitor without the bezel MDT552S satisfies the UL requirements as long as it is used with the bezel attached. When using the monitor

More information

CI-218 / CI-303 / CI430

CI-218 / CI-303 / CI430 CI-218 / CI-303 / CI430 Network Camera User Manual English AREC Inc. All Rights Reserved 2017. l www.arec.com All information contained in this document is Proprietary Table of Contents 1. Overview 1.1

More information

Minimailer 4 OMR SPECIFICATION FOR INTELLIGENT MAILING SYSTEMS. 1. Introduction. 2. Mark function description. 3. Programming OMR Marks

Minimailer 4 OMR SPECIFICATION FOR INTELLIGENT MAILING SYSTEMS. 1. Introduction. 2. Mark function description. 3. Programming OMR Marks OMR SPECIFICATION FOR INTELLIGENT MAILING SYSTEMS Minimailer 4 1. Introduction 2. Mark function description 3. Programming OMR Marks 4. Mark layout requirements Page 1 of 7 1. INTRODUCTION This specification

More information

First Question: Camera head. Lighting unit. Shooting stage

First Question: Camera head. Lighting unit. Shooting stage Elmo P30 Visualiser First Question: Q. Is everyone familiar with exactly what a visualiser is? A. A visualiser is effectively a camera on an arm, usually with a shooting stage and its own lighting source.

More information

QUICK START GUIDE QT ANALOG HD CAMERA & DVR BUNDLE ENGLISH

QUICK START GUIDE QT ANALOG HD CAMERA & DVR BUNDLE ENGLISH QUICK START GUIDE QT ANALOG HD CAMERA & DVR BUNDLE ENGLISH Table of Contents Welcome What s Included...3 Understanding your DVR...4 Get Connected Registration...5 Connect Your Cameras...5 Connect DVR to

More information

C Module Description

C Module Description IQMMX -Input Router & ASI Distribution Amplifier C Module Description The IQMMX is an ASI to 1 switch, distribution amplifier and transport stream switcher with up to 8 outputs in double width form or

More information

VBOX 3i Dual Antenna Measures Slip and Pitch/Roll (RLVB3iSL)

VBOX 3i Dual Antenna Measures Slip and Pitch/Roll (RLVB3iSL) A VBOX 3i Dual Antenna (VB3iSL) uses a GPS/GLONASS receiver to achieve high level accuracy has the ability to measure slip and pitch/roll angles at 100 Hz. Enabling users to intuitively measure set parameters

More information

VOB - data over Video Overlay Box

VOB - data over Video Overlay Box VOB - data over Video Overlay Box Real time data overlayed onto video, both PAL and NTSC versions available Real time lap and sector times without a track side optical beacon User configurable display,

More information

Operation Guide Version 2.0, December 2016

Operation Guide Version 2.0, December 2016 Operation Guide Version 2.0, December 2016 Document Revision History Revision Date Description v1.0 January 8, 2016 Initial release of COLR Operation Manual, based on firmware version 1.0.1 CONTENTS Contents...

More information

Model#: IN-MDRI3MF. Hardware User Manual. 3MP Indoor Mini Dome with Basic WDR, Fixed lens. (PoE) Ver. 2013/02/04

Model#: IN-MDRI3MF. Hardware User Manual. 3MP Indoor Mini Dome with Basic WDR, Fixed lens. (PoE) Ver. 2013/02/04 Model#: IN-MDRI3MF 3MP Indoor Mini Dome with Basic WDR, Fixed lens Hardware User Manual (PoE) Ver. 2013/02/04 Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents... 4 Features and Benefits...

More information

Operation Guide Version 1.0, December 2015

Operation Guide Version 1.0, December 2015 Operation Guide Version 1.0, December 2015 Document Revision History Revision Date Description v1.0 January 8, 2016 Initial release of COLR Operation Manual, based on firmware version 1.0.1 CONTENTS Contents...

More information

C8000. sync interface. External sync auto format sensing : AES, Word Clock, Video Reference

C8000. sync interface. External sync auto format sensing : AES, Word Clock, Video Reference features Standard sync module for a frame Internal sync @ 44.1 / 48 / 88.2 / 96kHz External sync auto format sensing : AES, Word Clock, Video Reference Video Reference : Black Burst (NTSC or PAL) Composite

More information

Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module

Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Helvar Data is subject to change without notice. www.helvar.com i Contents Section Page Introduction 1 Installation 2 1. Attach

More information

Gazer VI700A-SYNC2 and VI700W- SYNC2 INSTALLATION MANUAL

Gazer VI700A-SYNC2 and VI700W- SYNC2 INSTALLATION MANUAL Gazer VI700A-SYNC2 and VI700W- SYNC2 INSTALLATION MANUAL Contents List of compatible cars... 3 Package contents... 4 Special information... 6 Car interior disassembly and connection guide for Ford Focus...

More information

MS2540 Current Loop Receiver with RS485 Communication

MS2540 Current Loop Receiver with RS485 Communication MS2540 Current Loop Receiver with RS485 Communication User Manual Metal Samples Company A Division of Alabama Specialty Products, Inc. 152 Metal Samples Rd., Munford, AL 36268 Phone: (256) 358 4202 Fax:

More information

C Module Description

C Module Description ASI Distribution Amplifier with Signal Inversion C Module Description The is an ASI distribution amplifier with up to 8 outputs in double width or 4 outputs in single width. The input is transformer coupled

More information

BecauseRFL andhubbel haveapolicyofcontinuousproductimprovement,wereservetherighttochangedesignsandspecificationswithoutnotice.

BecauseRFL andhubbel haveapolicyofcontinuousproductimprovement,wereservetherighttochangedesignsandspecificationswithoutnotice. 1. Introduction 1.1 Overview The RFL VS800 CODEC enables high quality video transmission combined with voice and data over E1 (2.048Mbit/s), T1 (1.55Mbit/s) or Ethernet links. This provides an alternative

More information

Quick Guide Book of Sending and receiving card

Quick Guide Book of Sending and receiving card Quick Guide Book of Sending and receiving card ----take K10 card for example 1 Hardware connection diagram Here take one module (32x16 pixels), 1 piece of K10 card, HUB75 for example, please refer to the

More information

Installation Note. Agilent 89441A Option AYC Installation Kit

Installation Note. Agilent 89441A Option AYC Installation Kit Installation Note Agilent 89441A Option AYC Installation Kit Part Number: 89441-90074 Printed in USA February 2002 Notice. The information contained in this document is subject to change without notice.

More information

Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display.

Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display. Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display. Your Stack ST8961 VS module allows you to synchronize, overlay, and record data available on your Stack

More information

INSTALATION AND OPERATION MANUAL ABYSSAL OS Overlay Module Version 1.3

INSTALATION AND OPERATION MANUAL ABYSSAL OS Overlay Module Version 1.3 INSTALATION AND OPERATION MANUAL ABYSSAL OS Overlay Module Version 1.3 Thank you for purchasing the Abyssal OS Overlay Module for your ROV. This instruction manual contains all the information you ll need

More information

Document History Version Comment Date

Document History Version Comment Date FAQ Inspector 2 (12) Document History Comment Date 1.04 Created 2008-09-11 Corrected the headline of S03 issue and the title name in the global header field 3 (12) Table Of Contents DOCUMENT HISTORY...

More information

Kramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher

Kramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in

More information

Quick Setup Guide for IntelliAg Model NTA

Quick Setup Guide for IntelliAg Model NTA STEP 3: Auto Configuration (identifies sensors connected to each module) Auto config is performed at the factory, but may need to be done in the field as changes are made to the system or if options are

More information

Troubleshooting the CTS 1100

Troubleshooting the CTS 1100 CHAPTER 7 Troubleshooting the CTS 1100 Revised: November 2011, Contents You may want to periodically test system components using the hardware and software tests available in the Cisco TelePresence System

More information

LM/TM-30xx, 31xx Series LCD Monitor User s Manual Rev. A0

LM/TM-30xx, 31xx Series LCD Monitor User s Manual Rev. A0 LM/TM-30xx, 31xx Series LCD Monitor User s Manual Rev. A0 FCC NOTICE This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions

More information

2002 Martin Professional A/S, Denmark.

2002 Martin Professional A/S, Denmark. Freekie user manual 2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional

More information

Gazer VI700A-SYNC/IN and VI700W- SYNC/IN INSTALLATION MANUAL

Gazer VI700A-SYNC/IN and VI700W- SYNC/IN INSTALLATION MANUAL Gazer VI700A-SYNC/IN and VI700W- SYNC/IN INSTALLATION MANUAL Contents List of compatible cars... 3 Package contents... 4 Special information... 6 Car interior disassembly and connection guide for Ford

More information

1 OVERVIEW 2 WHAT IS THE CORRECT TIME ANYWAY? Application Note 3 Transmitting Time of Day using XDS Packets 2.1 UTC AND TIMEZONES

1 OVERVIEW 2 WHAT IS THE CORRECT TIME ANYWAY? Application Note 3 Transmitting Time of Day using XDS Packets 2.1 UTC AND TIMEZONES 1 OVERVIEW This application note describes how to properly encode Time of Day information using EIA-608-B Extended Data Services (XDS) packets. In the United States, the Public Broadcasting System (PBS)

More information

1. Get support Attention Safety Caution Applications View Cameras on Screen (ex. HD TV or PC monitor) 3. Change Time Zone 5

1. Get support Attention Safety Caution Applications View Cameras on Screen (ex. HD TV or PC monitor) 3. Change Time Zone 5 1. Get support 1 2. Attention 1 3. Safety Caution 1 4. Applications 1 5. View Cameras on Screen (ex. HD TV or PC monitor) 3 Change Time Zone 5 6. Installation Guide for ONWOTE Cameras 6 7. View Cameras

More information

QUICK START GUIDE. QT Analog HD Camera & DVR Bundle ENGLISH

QUICK START GUIDE. QT Analog HD Camera & DVR Bundle ENGLISH QUICK START GUIDE QT Analog HD Camera & DVR Bundle ENGLISH Table of Contents Welcome What s Included...3 Understanding your DVR...4 Get Connected Registration...5 Connect Your Cameras...5 Connect DVR to

More information

Configuration Vestas VMP3500

Configuration Vestas VMP3500 Configuration Vestas VMP3500 1. Table of contents 1. Table of contents... 2 2. Introduction... 3 3. Vestas turbines (RCS)... 4 3.1. VMP 3500 controller... 4 3.2. Communication with the CT3230 current loop

More information

COLOR TFT LCD MONITOR. Manual

COLOR TFT LCD MONITOR. Manual COLOR TFT LCD MONITOR Manual Safety defended: Properly maintains your system to be possible to guarantee its service life and to reduce the damage risk. It should avoid the damp and exceeding temperature

More information

Mini Micro Pulse Lidar System

Mini Micro Pulse Lidar System Mini Micro Pulse Lidar System MiniMPL-532-C Sensor Suite Operations Manual Version: June 2016 THIS PAGE INTENTIONALLY LEFT BLANK 2 Table of Contents MINIMPL SENSOR SUITE SYSTEM: RECORD OF PURCHASE... 4

More information

LG Digital Signage *MFL * Easy Setup Guide (MONITOR SIGNAGE)

LG Digital Signage *MFL * Easy Setup Guide (MONITOR SIGNAGE) Easy Setup Guide LG Digital Signage (MONITOR SIGNAGE) Please read this manual carefully before operating your set and retain it for future reference. 47LV35A 55LV35A *MFL68621511* P/NO : MFL68621511(1608-REV00)

More information

Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9

Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9 Light-Switch & Switch-Edit Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9 Artistic Licence Engineering Ltd. Switch-Edit Manual 2/47 Artistic Licence Engineering Ltd. Switch-Edit

More information

VSP 168HD Quick Start

VSP 168HD Quick Start VSP 168HD Quick Start Support 10Gbps of transmission rate Support HDBaseT protocols and standards Support USB upgrade Max 2048 1152@60Hz/2560 816 60Hz input/output resolution Support custom output resolution

More information

Noise Detector ND-1 Operating Manual

Noise Detector ND-1 Operating Manual Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation

More information

Logic Controls LV3000 VGA Connected Virtual Pole Display

Logic Controls LV3000 VGA Connected Virtual Pole Display One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Logic Controls LV3000 VGA Connected Virtual Pole Display This

More information

Part 1 Basic Operation

Part 1 Basic Operation This product is a designed for video surveillance video encode and record, it include H.264 video Compression, large HDD storage, network, embedded Linux operate system and other advanced electronic technology,

More information

KRAMER ELECTRONICS LTD. USER MANUAL

KRAMER ELECTRONICS LTD. USER MANUAL KRAMER ELECTRONICS LTD. USER MANUAL MODEL: Projection Curved Screen Blend Guide How to blend projection images on a curved screen using the Warp Generator version K-1.4 Introduction The guide describes

More information

IMPORTANT! This instruction guide explains how to install your CCTV system.

IMPORTANT! This instruction guide explains how to install your CCTV system. IMPORTANT! This instruction guide explains how to install your CCTV system. Which accessories do you need before getting started? 1. Monitor or TV (recommended not less than 19" for clear viewing) 2. HDMI

More information

DeviceConfig. User Guide. Camera configuration tool (RS232, GigE, Camera Link) V April 2012

DeviceConfig. User Guide. Camera configuration tool (RS232, GigE, Camera Link) V April 2012 DeviceConfig User Guide Camera configuration tool (RS232, GigE, Camera Link) V2.0.0 05 April 2012 Allied Vision Technologies GmbH Taschenweg 2a D-07646 Stadtroda / Germany Legal notice Trademarks Microsoft,

More information

Broadcast A / V Division M-LYNX-702 V.3. Dual 7 LCD Display. User Manual

Broadcast A / V Division M-LYNX-702 V.3. Dual 7 LCD Display. User Manual Broadcast A / V Division M-LYNX-702 V.3 Dual 7 LCD Display User Manual Table of Contents Table of Contents 1. Package Includes 2. Product Description 2.1 Front Panel 2.2 Rear Panel Connections 3. On-Screen

More information

Broadcast A/V Division M-LYNX-702 V.3. Dual 7 LCD Display. User Manual

Broadcast A/V Division M-LYNX-702 V.3. Dual 7 LCD Display. User Manual Broadcast A/V Division M-LYNX-702 V.3 Dual 7 LCD Display User Manual 1. Package Includes Table of Contents 1. Package Includes Table of Contents 01 02 One M-LYNX-702 Monitor One universal AC power adapter

More information

EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY

EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY 493456301 Rev B April 2009 Table of Contents Installation... 1 Setup... 2 Operation... 4 Live Video... 4 Video Settings... 5 Network

More information

EVD-L04/100A1-960, EVD-L08/200A1-960 and. EVD-L16/400A1-960 DVRs. Quick Operation Guide

EVD-L04/100A1-960, EVD-L08/200A1-960 and. EVD-L16/400A1-960 DVRs. Quick Operation Guide EVD-L04/100A1-960, EVD-L08/200A1-960 and EVD-L16/400A1-960 DVRs Quick Operation Guide Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

More information

D-901 PC SOFTWARE Version 3

D-901 PC SOFTWARE Version 3 INSTRUCTION MANUAL D-901 PC SOFTWARE Version 3 Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.

More information

Setting Up the Warp System File: Warp Theater Set-up.doc 25 MAY 04

Setting Up the Warp System File: Warp Theater Set-up.doc 25 MAY 04 Setting Up the Warp System File: Warp Theater Set-up.doc 25 MAY 04 Initial Assumptions: Theater geometry has been calculated and the screens have been marked with fiducial points that represent the limits

More information

Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting

Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting PRODUCT ADC TOPIC ODETICS TCS-2000 CART MACHINE DATE: May 14, 1999 REVISION HISTORY Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting 1999 Olitzky 1.0 Aug.

More information

Video Extender DS128 DSRXL. Instruction Manual. 8-Port Cat5 VGA Digital Signage Broadcaster with RS232 and Audio

Video Extender DS128 DSRXL. Instruction Manual. 8-Port Cat5 VGA Digital Signage Broadcaster with RS232 and Audio DS128 DSRXL Instruction Manual Video Extender 8-Port Cat5 VGA Digital Signage Broadcaster with RS232 and Audio Cat5 VGA Digital Signage Receiver with RS232 and Audio FCC Compliance Statement This equipment

More information

UHF REMOTE RECEIVER INSTALLATION & PROGRAMMING

UHF REMOTE RECEIVER INSTALLATION & PROGRAMMING UHF REMOTE RECEIVER INSTALLATION & PROGRAMMING Table of Contents Section Page No INTRODUCTION... 3 TOOLS & TEST EQUIPMENT... 4 RECEIVER POSITION... 4 UHF REMOTE RECEIVER RELEVANT HIGH GAIN AERIALS... 4

More information

VBOX III 100Hz GPS Speed Sensor. User Guide. Page 1 of 21. VBOX III SPS User Guide

VBOX III 100Hz GPS Speed Sensor. User Guide. Page 1 of 21. VBOX III SPS User Guide VBOX III 100Hz GPS Speed Sensor User Guide Page 1 of 21 VBOX III OVERVIEW... 3 INTRODUCTION... 4 FEATURES... 4 STANDARD INVENTORY... 5 OPTIONAL ACCESSORIES... 5 OPERATION... 6 GETTING STARTED... 12 VBOX.EXE

More information

Cablecast Server. Setup Guide. c Tightrope Media Systems For Cablecast version Build 74

Cablecast Server. Setup Guide. c Tightrope Media Systems For Cablecast version Build 74 Cablecast Server Setup Guide c Tightrope Media Systems For Cablecast version 6.1.2 Build 74 Printed July 22, 2016 1 Cablecast Server Setup 1.1 Prerequisites 1.2 Overview of Setup Thank you for purchasing

More information

REMOTE I/O R30 SERIES. PC CONFIGURATOR SOFTWARE Model: R30CFG Ver Users Manual

REMOTE I/O R30 SERIES. PC CONFIGURATOR SOFTWARE Model: R30CFG Ver Users Manual REMOTE I/O R30 SERIES PC CONFIGURATOR SOFTWARE Model: R30CFG Ver. 1.13 Users Manual 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Tel: +81-6-6659-8201 Fax: +81-6-6659-8510 http://www.m-system.co.jp/

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS MATRIX SYSTEM SX-2000 SERIES Thank you for purchasing TOA's Matrix System. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

More information

Operating Instructions

Operating Instructions Marshall Electronics Broadcast A/V Division Model No. VSW-2200 4-Input Seamless SDI A/V Switcher Operating Instructions Table of Contents 1. Overview... 2. Features.... Package Contents... 4. Specifications...

More information

RDS: The RDS, or Radio Data System, is supported in the g! interface where available.

RDS: The RDS, or Radio Data System, is supported in the g! interface where available. Manufacturer: Integra Integration Note Model Number(s): Integra 20.3/30.3/40.3/50.3/70.3/80.3 Core Module Version: 5.4 Comments: FW 1.09 (1091-0999-0210-9105) Document Revision Date: 1/15/2013 OVERVIEW

More information

POINTS POSITION INDICATOR PPI4

POINTS POSITION INDICATOR PPI4 POINTS POSITION INDICATOR PPI4 Monitors the brief positive operating voltage across points motors when they are switched Lights a corresponding led on a control panel to show the last operation of each

More information

NOTICE: This document is for use only at UNSW. No copies can be made of this document without the permission of the authors.

NOTICE: This document is for use only at UNSW. No copies can be made of this document without the permission of the authors. Brüel & Kjær Pulse Primer University of New South Wales School of Mechanical and Manufacturing Engineering September 2005 Prepared by Michael Skeen and Geoff Lucas NOTICE: This document is for use only

More information

BY-HPE11KTA. Operating Instructions. Coaxial - LAN Converter with PoE function. Indoor Use Only. Model No. Attached Installation Guide

BY-HPE11KTA. Operating Instructions. Coaxial - LAN Converter with PoE function. Indoor Use Only. Model No. Attached Installation Guide Operating Instructions Coaxial - LAN Converter with PoE function Model No. Indoor Use Only BY-HPE11KTA Attached Installation Guide Before attempting to connect or operate this product, please read these

More information

Troubleshooting. 1. Symptom: Status indicator (Red LED) on SSR is constant on. 2. Symptom: Output indicator (Yellow LED) on SSR is flashing.

Troubleshooting. 1. Symptom: Status indicator (Red LED) on SSR is constant on. 2. Symptom: Output indicator (Yellow LED) on SSR is flashing. Product Data Electrical Data SST (Transmitter) SSR (Receiver) Supply voltage 18 30 V dc Max. Voltage ripple 15 % (within supply range) Current consumption 100 ma (RMS) 75 ma Digital - 100 ma Max. outputs

More information

DUAL/QUAD DISPLAY CONTROLLER Operation Manual

DUAL/QUAD DISPLAY CONTROLLER Operation Manual DUAL/QUAD DISPLAY CONTROLLER Operation Manual Model PXD524 MicroImage Video Systems division of World Video Sales Co., Inc PO Box 331 Boyertown, PA 19512 Phone 610-754-6800 Fax 610-754-9766 sales@mivs.com

More information

HD-1603 Single Input MPEG-4 DVB-T HD Encoder/Modulator User Guide and Install Manual

HD-1603 Single Input MPEG-4 DVB-T HD Encoder/Modulator User Guide and Install Manual ZyCastR digi-mod HD Range digi-mod HD-1603 www.digi-modbyzycast.com HD-1603 Single Input MPEG-4 DVB-T HD Encoder/Modulator User Guide and Install Manual Table of Contents www.digi-modbyzycast.com Safety

More information

User Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor

User Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor Touch Display LCD Monitor User Manual Installation Guide 15 Resistive Touch LCD Monitor MODEL: KK1500-TR i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com User

More information