Panzer 3.0 Assembly Instructions & Checklist
|
|
- Clyde Garrett
- 5 years ago
- Views:
Transcription
1 Panzer 3.0 Assembly Instructions & Checklist
2 Parts Included & Preparation
3 Legend A. 5x Silver M4 Aluminum Screws B. 4x Screws C. 8x 4-40 Pan head Screws D. 2x 4-40 Flat head Screws E. 2x 4-40 Nuts F. 4x #6 Flat Washer G. 4x #6 Lock Washer H. 2x Star Washer I. 4x 6-32 ¼ Truss Head Screws J. 1x JST 4-pin 1x Molex 4-pin & 1x 20 pin header (For Brook UFB) K. ¼ Joystick Spacer L. 4x Case Feet M. 1x 20p IDC Cable N. 1x START/HOME/SELECT Harness O. 1x 5-pin Unpowered Joystick Harness P. 1x 6-pin Powered Joystick Harness Q. 1x L3/TP/R3 Harness R. 1x LS/DP/RS Rocker Harness S. 1x 4-pin 4-pin LS/DP/RS Interconnect Cable T. 1x Kill Ground Rocker Harness U. 1x L3/TP/R3 Click Jumper V. 8x 30mm Button Harness W. 1x Right Angle USB Cable X. 1x Jasen s Customs EZ Build Board Y. 1x Neutrik Quick-Disconnect USB Passthrough Z. 1x Neutrik Quick-Disconnect USB Passthrough Gasket
4 Soldered Connectors This Picture Provides reference for appropriate placement of soldered connectors.
5 Step 1 Take off the protective film from the plexiglass, and using the five provided Silver M4 Aluminum Bolts, screw down in an X pattern ( ) being careful to not overly tighten and crack the plexiglass.
6 Step 2 Install the Neutrik Quick-Disconnect USB Passthrough, and six 24mm Buttons in the front of the Panzer case. It may require small force to install the Neutrik. After inserting the 4-40 Flat Head Screws, insert the Star Washer first, then tighten the applicable 4-40 nut.
7 Step 3 Attach the LS/DP/RS harness to the 3-way rocker switch (ON-OFF-ON). Attach the Lock Button Harness to the 2-way rocket switch (ON-OFF).
8 Step 4 Insert the previously prepared rocker switches into the mounting holes, being careful to pay attention to the tabs pressed out of the case, and the orientation of the switches when inserting.
9 Step 5 Screw in the EZ Build Board, again, alternating in a cross pattern, tightening in the sequence Be careful to not overly tighten the screws, and crack the PCB.
10 Step 6 Plug the L3/TP/R3 harness into the right cluster of buttons, and the HOME/SELECT/START harness into the left cluster of buttons. Appropriate plugin points are marked on the EZ Build Board. Pay attention to the lengths of the wire on the L3/TP/R3 harness, enlarged to show the correct sequence.
11 Step 7 Plug in the previously prepared and mounted rocker switches to the EZ Build Board, appropriate plug-in points are marked. (You can t mess this one up. It won t reach otherwise!)
12 Step 8 Prepare your buttons, by attaching the 8 provided 30mm Button Harness. This is much easier to do before inserting buttons into the case.
13 Step 9 Before inserting buttons, it would be wise to route the Right Angle USB cable from the Neutrik, underneath the EZ Build Board. The ends are too big to squeeze between the posts and buttons afterwards. Attach all buttons to the appropriate plug-in points.
14 Step 9a When this switch is in the KGND position the LS/DP/RS rocker is disabled when the Front Panel connectors are switched OFF. When in the GND position, it will be active and the lever can switch to LS/RS mode at any time.
15 Step 10 Lay the Joystick Spacer on top of the 4 risers protruding from the case, and screw in your joystick to the case. It s advised to place the lock washer, and then flat washer on the bolt (in that order) before mounting. Plug-in point to the EZ Build Board is marked. Yours will not look like spaghetti like mine. (I m using a harness adapter) : )
16 Step 11 Finally, screw in the Brook Universal Fighting Board, and plug-in to the EZ Build Board using the provided 20-Pin IDC Cable, 4-Pin 4-Pin Cable, and L3/TP/R3 jumper cable. These can all only plug in one possible way, so it s fairly straightforward.
17 Step 12 When screwing the case back together now, make sure to take notice you have the notched side (circled) facing towards the front-facing buttons and quick disconnect. This allows clearance for the Neutrik s mounting bolts.
18 You re done! Enjoy your new Panzer Fightstick 3.0!
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that
More informationMP Maker Pro Mk.1. Quick Start Guide
MP Maker Pro Mk.1 P/N 33013 Quick Start Guide ONLINE SUPPORT Monoprice is pleased to provide free online support. For order related issues, contact the Customer Service department through the Live Chat
More informationWaterVue TV Installation & User Manual
WaterVue TV Installation & User Manual 19 Waterproof TV Dimensions of TV Front screen 486mm x 340mm x 3mm Mounting Plate 467mm x 324mm x 48mm 24 Waterproof TV Dimensions of TV Front screen 576mm x 395mm
More informationTen-Tec (865) Service Department:(865)
Ten-Tec (865) 453-7172 Service Department:(865) 428-0364 Installation Instructions for Ten-Tec Jupiter AT538K Tuner Kit The installation of the AT538K is divided into two steps. The first step is to reprogram
More informationAUDIO ROOF KIT P/N , , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
AUDIO ROOF KIT P/N 2882064, 2882065, 2882066 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationMal-2 assembly guide v1.0
Mal-2 assembly guide v.0 SONIC POTIONS Schematic and BOM The BOM can be found on Google Docs Prepare the PCB Separate the PCBs using some pliers. PCB We start with the lower PCB and assemble it beginning
More informationCommissioning Guide. firepickdelta. Commissioning Guide. Written By: Neil Jansen firepickdelta.dozuki.com Page 1 of 22
firepickdelta Commissioning Guide Written By: Neil Jansen 2017 firepickdelta.dozuki.com Page 1 of 22 Step 1 Pre-Requisites Before commissioning, please make sure ALL of the following steps have been completed,
More informationELECTRONIC GAME KIT ESSENTIAL INFORMATION. Version 2.0 BUILD YOUR OWN MEMORY & REACTIONS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS BUILD YOUR OWN MEMORY & REACTIONS ELECTRONIC GAME KIT Version 2.0 Build Instructions Before
More informationSEP Bright Pi v1.0 Assembly Instructions
SEP Bright Pi v1.0 Assembly Instructions When you purchased your Bright Pi v1.0 kit, you should have received an anti-static bag with some components in it which will require soldering together in order
More informationMulti-Key v2.4 Multi-Function Amplifier Keying Interface
Multi-Key v2.4 Multi-Function Amplifier Keying Interface ASSEMBLY & OPERATION INSTRUCTIONS INTRODUCTION The Harbach Electronics, LLC Multi-Key is a multi-function external device designed for the safe
More informationCable ISOBUS Active Termination
ISOBUS Retrofit Kit Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity ISOBUS Retrofit Kit 4100843 1 Hex Head Bolt
More informationimac Intel 20" EMC 2133 and 2210 LCD Backlights (CCFL) Replacement
imac Intel 20" EMC 2133 and 2210 LCD Backlights (CCFL) Replacement The CCFL back lights are replaceable. I have pulled mine apart and documented my method. '''NOTE''' This is not for the feint hearted!
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws M4 x 14mm (x1) Silver
More informationDLMP Installation Instructions
DLMP Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420 [ ] 2 x
More informationMUK REAR PANEL ASSEMBLY ASSEMBLY INSTRUCTIONS
Rev B. 13 August 2017 ASSEMBLY INSTRUCTIONS The Midnight Ultimate Keyer (MUK) consists of two functional assemblies: Rear Panel containing the interface and power connectors. Front Panel containing the
More informationTurret Replacement Instruction Manual
Automatic Multi-Satellite TV Antenna Turret Replacement Instruction Manual for models RPSKLGL, RPSKSML, SK-LG00, SK-SM00, & RP-SWM For help, email help@winegard.com or call -800-788-7 568 Raising the Antenna
More informationM1, M2GO and M2PC MIDI PCB Module Installation Guide SMPTE PCB Module Installation Guide
M1, M2GO and M2PC MIDI PCB Module Installation Guide SMPTE PCB Module Installation Guide Author Part number Date Matthias Hinrichs/Chris Foblets 35000620-B 20.06.2012 This guide is also available for download
More informationDLMP-45/45R Installation Instructions
DLMP-45/45R Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420
More informationFormulate Designer Series 20 Backwall - Kit 07
Formulate Designer Series 20 Backwall - Kit 07 FMLT-DS-20-07 Formulate TM Designer Series 20ft displays have unique stylistic features and shapes, are portable and easy to assemble. The aluminum tube frame
More informationDocumentation VFD clock 8 a clock
Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success
More informationPaPiRus Assembly Tips And Gotchas
PaPiRus Assembly Tips And Gotchas In this tutorial we are going to look at some tips and gotchas about the PaPiRus HAT and the PaPiRus Zero epaper diplays. This is what's covered in this tutorial: Connect
More informationDIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX
DIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX 2015 FRS & MSXpró. Translation by FRS and Supersoniqs. Table of Contents Introduction... 3 Materials needed... 3 Audio volume boost...
More informationDescription: Major features and benefits
July 2011 DFMC DMC(V) Description: Phoenix Contact introduces a new line of stacked headers and plugs that provide a higher density application than previously available in a European-style terminal block.
More informationTV Lift System Model CL-65 Installation Instructions
TV Lift System Model CL-65 Installation Instructions Contact: Support@Nexus21.com Toll Free: (866) 500-5438 Phone: (480) 951-6885 Fax: (480) 951-6879 Revised: 01/17/17 Below is a parts list describing
More informationMAKE AN RGB CONTROL KNOB.
MAKE AN RGB CONTROL KNOB. This is a knob based colour changing controller that uses a custom programmed microcontroller to pack a lot of features into a small affordable kit. The module can drive up to
More informationHN Connectors. Automatic Connector. Introduction. Contents. 631/ FAX 631/
Connectors Introduction 2004 Automatic Connector. All rights reserved. pdf 1.0 4-13-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable
More informationTechnical Information Bulletin
June 4, 2001 #TIB0003 Units Affected: Model Serial Numbers Model Serial Numbers SVT-2PRO T2PDxxxxxxxxx SVTAV AXVDxxxxxxxxx ATLDxxxxxxxxx BJIDMAxxxxxxx SVT-2PROJ T2PJxxxxxxxxx SVTAVJ BAHJxxxxxxxxx ATLJxxxxxxxxx
More informationRobot Preemptive Troubleshooting
Robot Preemptive Troubleshooting In FIRST Robotics Competion, robots take a lot of stress while driving around the field. It is important to make sure that connections are tight, parts are bolted securely
More informationElecraft KXAT2 Automatic Antenna Tuner Installation Instructions
Elecraft KXAT2 Automatic Antenna Tuner Installation Instructions Revision A, May 23, 2016 E740294 Copyright 2016, Elecraft, Inc. All Rights Reserved Introduction The KXAT2 internal automatic antenna tuner
More informationMounting Set ACCESSORIES
Mounting Set ACCESSORIES 271 Lupa-con Connector EPCOM/2 Flat Article Number Product Name Color Ends 5.01.0383 Lupa-con EPCOM/2 Connector Flat Black 5.01.0384 Lupa-con EPCOM/2 Connector Flat Black Lupa-con
More informationStep 1. 2x Kep Nut 1x Left Motor Assembly
Start with the build completed in Lesson 3 of the TETRIX Getting Started Guide. Steps 1 to 3 involve removing elements from the model. These elements will be reattached later. Parts to be Removed Step
More informationSafety Rules Parts Check Lists and Photos Cable Diagrams for Various Crane Configurations Step by Step Instructions Tips for Packaging and Storage
EZ CRANE USER MANUAL INCLUDED INSIDE Safety Rules Parts Check Lists and Photos Cable Diagrams for Various Crane Configurations Step by Step Instructions Tips for Packaging and Storage WATCH THE INSTRUCTIONAL
More informationPelican PL-957. Adding additional Tos Link (Digital Optical) inputs, and / or IR Remote
Pelican PL-957 Adding additional Tos Link (Digital Optical) inputs, and / or IR Remote Table of Contents: Background;... 2 Section 1: Adding TosLink receivers... 3 Section 2: Adding Remote Capability...
More informationTroubleshooting Guide 9630 Series
Troubleshooting Guide 9630 Series Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com 1305-SEMI
More informationLED Backlight for Technics amplifiers
LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to
More informationAutomatic Connector MHV Connectors MHV Introduction MHV series connectors Contents Polarized mating interfaces Anti-Rock mating interfaces
Automatic s 2004 Automatic. All rights reserved. pdf 1.0 3-18-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable Plugs...................
More informationSatellite Dish Installation Manual (Ver. 2) 1
Satellite Dish Installation Manual Provided by DiscoverNet, Inc. Satellite Dish Installation Manual (Ver. 2) 1 Table of Contents Section 1: Introduction Page 3 Section 2: Recommended Tools and Materials
More informationTeamWork Installation Guide
C G G 00-0V/ A MAX TX RX +V APARATUS US 0 TeamWork Installation Guide TeamWork TeamWork is a fully customizable collaboration system comprised of an switcher, Show Me cables, a control processor, and a
More informationRecognizing & Disconnecting Cable
Recognizing & Disconnecting Cable Connectors Get to know the various kinds of cable connectors found inside consumer electronics, and learn to disconnect them safely. Written By: Jeff Suovanen 2017 edu.ifixit.com
More informationCOLOUR CHANGING USB LAMP KIT
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE SEE AMAZING LIGHTING EFFECTS WITH THIS COLOUR CHANGING USB LAMP KIT Version 2.1 Index of Sheets TEACHING
More informationPage 1 of 8 SPECIAL INSTALLATION INSTRUCTIONS #M066. Low-Stress Robotic (LSR) Systems Installation Instructions For Motoman XRC EA1400/1900 Robots
SPECIAL INSTALLATION INSTRUCTIONS #M066 Low-Stress Robotic (LSR) Systems Installation Instructions For Motoman XRC EA1400/1900 Robots Summary Unlike the most recent through-arm robots from Motoman (EA1400N/1900N
More information8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit. Applicable Upgrade Kit Model Number
Installation Note 8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit Network Analyzer Model Number 8753E 8753ET 8753ES Applicable Upgrade Kit Model Number
More informationBriggs&Stratton 44Q B1
Accessories IPL, Briggs&Stratton 44Q777-1272-B1, 2010-03 Briggs&Stratton 44Q777-1272-B1 Spare parts Ersatzteile Pièces détachées Reserve onderdelen Repuestos Reservdelar 48 SHORT BLOCK 1329 REPLACMENT
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationMONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS MONO AMPLIFIER KIT Version 2.2 Build Instructions
More informationProcessing Specification MiniBridge IDC
Processing Specification MiniBridge IDC ERNI Electronics GmbH & Co. KG Seestrasse 9 l 73099 Adelberg / Germany l +49 7166 50-0 l www.erni.com Version 5 IMS Verarbeitungsspezifikationen Seite 1 von 11 Table
More informationDX-10 tm Digital Interface User s Guide
DX-10 tm Digital Interface User s Guide GPIO Communications Revision B Copyright Component Engineering, All Rights Reserved Table of Contents Foreword... 2 Introduction... 3 What s in the Box... 3 What
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationHamcrafters K44 CW Keyboard/Reader Kit Assembly Guide Revision A.0
Introduction Figure 1 Assembled K44 This document will describe how to assemble and test a K44 Kit. The assembly requires reasonably good soldering skill. Before you start working, gather the following
More informationCheck what you have received against the component checklist and hardware above.
SA46S SA46W SA46B SA46PB Component Checklist Installation Instructions SYSTEMA Systema Monitor Arm 460mm HARDWARE Display Mounting Spacers (x4) Display Mounting Screws Arm Assembly VESA monitor head M4
More informationC2 +5V. (14) Vdd (+5 Vdc) (13) OSC1/A7 1.2K (12) 1.2K (11) 1.2K (10) U1 16F628 16F628A 1.2K (1) A2 1.2K (8) 1.2K (7) 1.2K. (Gnd) Vss (5) (6) 1.
CN1 Power Sw. SW1 CN2 C1 VR1 78L05 or LP2950ACZ- 5.0 +5V.1uf.1uf 9V Battery Fast Scan (Open) Slow Scan (Closed) Activity LED Reserved for LCD Serial Display R1 10K R2 10K SW2 CN3 LD1 R3 (16) (15) OS/A6
More informationPowerBook G4 Aluminum 12" GHz LCD panel upgrade
PowerBook G4 Aluminum 12" 1-1.5 GHz LCD panel upgrade Upgrade a 1400x1050 LCD panel. Written By: martin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The original LCD 1024x768 resolution
More informationBas Gialopsos Atari PureVideo Encoder Module 2600VECr5.2
Bas Gialopsos 2014 Atari PureVideo Encoder Module 2600VECr5.2 Table of Contents Description Disclaimer Technical and Signal Identification Installation Instructions Tools Required Caution Installation
More informationDIY KIT MHZ 8-DIGIT FREQUENCY METER
This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).
More informationStep 1. 1x NXT Ultrasonic Sensor
Start with the build completed in Lesson 3 of the TETRIX Getting Started Guide. Step 1 involves removing an element from the model. This element will be reattached later. Parts to be Removed Step 1 1x
More informationMain Products. Cable Assemblies Wire Harnesses Raw Cables. Connectors
About BMA BMA technology Ltd was found in Hong Kong in 2009. Our factory is located in Guangdong, China. With the 10,000m 2 production area, we are able to hold 500 workers during the peak season. Our
More informationThe Mambo Twist LED Screen System
The Mambo Twist LED Screen System The Mambo Twist LED screen system builds on the successful design formula of the Mambo range The Mambo screen system features: 8mm pixel pitch Indoor/outdoor use Light
More informationOrder #XXXXX - ECO x10 Inline Display. Setups. 10 Plan View
Order #XXXXX - ECO-054-0 x0 Inline Display Setups 0 0 Plan View 7A General Setup Instructions The setup instructions are created specifically for your configuration. Setup instructions are laid out sequentially
More informationSERIES BNC 50, COAXIAL MINIATURE CONNECTORS
SERIES BNC 50, COAXIAL MINIATURE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER BNC is still one of the most popular connector series, featuring a two stud bayonet coupling mechanism, which is particularly
More information3M Locator Plate N
M Locator Plate 44-107N Instructions for the assembly of.100 x.100 preassembled socket connectors 1.0 General The M Locator Plate 44-107N is designed to aid in the assembly of the preassembled socket connector
More informationAtari PICO Composite Mod Board Installation Instructions:
Atari PICO Composite Mod Board Installation Instructions: Installation Guide 6 Switch Atari 2600 6 Switch Video Mod Installation Guide Disclaimer: I am not responsible for any damage done to your Atari.
More informationMain PCB (The small one)
Thanks for choosing our kits! This manual is written taking with the problems that we usually find in our workshops in mind. Also the order is meant to make assembly as easy as possible. Some steps are
More informationPC-250. SMD Taped Parts Counter Operator s Manual. ISO 9001:2008 Certified. V-TEK, Incorporated 751 Summit Avenue Mankato, MN USA
PC-250 SMD Taped Parts Counter Operator s Manual ISO 9001:2008 Certified V-TEK, Incorporated 751 Summit Avenue Mankato, MN 56001 USA (P) 507-387-2039 (F) 507-387-2257 www.vtekusa.com Dear Customer: All
More informationWelcome to your. Wireless transmitter and receiver kit
Welcome to your Wireless transmitter and receiver kit Your Handykam camera Transmitter/Receiver (T/R) kit is designed to transmit and receive both pictures and sound (video and audio) with a choice of
More informationDIN EUROCARD CONNECTORS
DIN 41612 EUROCARD CONNECTORS 2230 SERIES SERIES. Vertical Female Type Half B Connectors. PCB Solder 4mm Wrap post tail length 13mm Wrap post tail length 17mm Soldar cable 16 a 2230 T061 2230 T063 2230
More informationPIEXX IC-EX243 px Installation Instructions
PIEXX IC-EX243 px Installation Instructions The PIEXX IC-EX243 px is a physical and electrical replacement for the original ICOM IC-EX243 Keyer. Specifications: Sends at speeds of 5-50 WPM Operates in
More informationVibratory Deck Sieves 15 in. (380 mm)
Instruction Sheet P/N 1604433-01 Vibratory Deck Sieves 15 in. (380 mm) Introduction This instruction sheet covers the vibratory deck sieves listed in the following tables. 15-Inch Deck Sieves with 2.5
More informationELECTRONIC CONNECTOR ASSEMBLY TRAINING CERTIFICATION EXAM (DVD-62C) v.1
This test consists of twenty multiple-choice questions. All questions are from the video: Electronic Connector Assembly DVD-62C. Use the supplied Answer Sheet and circle the letter corresponding to your
More informationBuilding a MidiBox LCD Cable
Building a MidiBox LCD Cable By Jim Henry, 3-Apr-2004 An LCD panel may be connected to the Core module by a 16 conductor flat ribbon cable. A 16 pin insulation displacement connector (IDC) terminates one
More informationInstalling iphone 3G Display
Tools used in this guide Phillips #00 Screwdriver (1) Small suction cup (1) Spudger (1) Parts relevant to this guide iphone 3G Display (1) Cracked or faulty display? Replacing the glass is somewhat involved
More informationFOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
More informationToughsat Flyaway Users Manual
Toughsat Flyaway Users Manual TOUGHSAT FLYAWAY USERS MANUAL V.1.6 September 2012 Important warning regarding your TOUGHSAT System All power to the system (controller, modem, external network devices) MUST
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More informationPATCH PANEL Easy Patch INSTRUCTION MANUAL
Page 1 BDA82-0 PATCH PANEL Easy Patch 96 Bantam (TT) Jacks 50 pin D-subminiature NPPA-TT-SD50 Easy Patch NPPA-TT-SD50 Page 2 BDA82-0 Index page 1 Electrical configuration 3 2 Re-Configuration and Replacement
More informationTR-Plus T/R Switch Assembly and Operation Manual. Introduction
TR-Plus T/R Switch Assembly and Operation Manual Revised: 7 February 2015 2015 Tucson Amateur Packet Radio Corporation Introduction The TAPR TR-Plus is a transmit/receive ( T/R ) switch that connects a
More informationBuild Your Own Clone Super 8 Kit Instructions
Build Your Own Clone Super 8 Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationAssembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door
CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the
More informationObjectives: Learn how LED displays work Be able to output your name on the display
Objectives: Learn how LED displays work Be able to output your name on the display By the end of this session: You will know how simple LED displays work and be able to make them give a useful output.
More information7 SEGMENT LED DISPLAY KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SCORE BOARD WITH THIS 7 SEGMENT LED DISPLAY KIT Version 2.0 Which pages of
More informationUAV Ultimate Atari Video A7800
UAV Ultimate Atari Video A7800 Basic Install guide because this is really easy mod to do! The UAV is a wonderful piece of tech for what it can do. To summarize, the UAV is a replacement video encoder and
More informationVT320X Large Screen Outdoor LCD
Solutions for Demanding Applications VARTECH S Y S T E M S I N C. Industrial CRT and Flat Panel Displays VT320X Large Screen Outdoor LCD User s Guide Read these instructions completely before attempting
More information2000i. Projector Replacement Guide. for Projector Replacement Kits. NEC MT1060R ( ) and NEC MT860R ( ) Interactive Whiteboard
2000i Interactive Whiteboard Projector Replacement Guide for Projector Replacement Kits NEC MT1060R (03-00043) and NEC MT860R (03-00041) 99-00496-00 Rev A0 FCC Warning This equipment has been tested and
More informationSite Installation Model MP-8433
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationMaterials: Programming Objectives:
Lessons Lesson 1: Basic Chassis Overview TETRIX Getting Started Guide In this lesson, users will learn how to use the elements of the TETRIX system that will be involved in building the basic chassis of
More informationSite Installation Model MP-8424
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationAssembly instructions
Assembly instructions Model: MXR0024/KIT TV Aerial - 18 Element Kit Contact: Helpline: +44 (0)1553 811000 Email: support@maxview.co.uk Web: www.maxview.co.uk Maxview reserve the right to change specifications
More informationField Service Procedure Replacement GACP Control Panel Kit, ST24
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the Graphic Antenna Control Panel (GACP) for the ST24 antenna. 2. Checklist: Verify Power to the GACP Verify Communications
More informationDDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1
DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1.1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be
More informationMitsubishi WD57734 DLP Chip Replacement
Mitsubishi WD57734 DLP Chip Replacement Replace the DLP chip in your Mitsubishi WD57734. Written By: David Sylvester ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION This guide will detail the
More informationOperating Manual. Automated Gear. Apollo Design Technology, Inc Fourier Drive Fort Wayne, IN USA
Operating Manual Automated Gear Apollo Design Technology, Inc. 4130 Fourier Drive Fort Wayne, IN 46818 USA PH: +01(260)497-9191 FX: +01(260)497-9192 www.apollodesign.net 11-25-09 5-6 POWERING UP THE RIGHT
More informationFord F Super Duty and E Series Installa4on Instruc4ons
Ford F Super Duty and E Series Installa4on For more information, contact your local Motion Reseller or Motion Representative wwwmotioncomputingcom 1) Using a plas,c trim panel removal tool, take out the
More informationField Service Procedure Replacement EL Motor Kit, ST24
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the elevation motor and encoder on the ST24 antenna. 2. Checklist: Verify Initialization Run the Built In Test 3. Theory
More informationIndustrial Monitor Update Kit
Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part
More informationTeamWork Kits Installation Guide
TX 0 RX COM +5V APARATUS US TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher, system controller, Cable Cubby, and cables
More informationStep What to do Expected result What to do if test fails Component tested 1 Visual inspection. Board is accurately assembled
Fox Delta Amateur Radio Projects & Kits AAZ-0914A 50MHZ Antenna Analyzer Testing Guide by Tony / I2TZK SWR Analyzer 4 steps for a quick test Step What to do Expected result What to do if test fails Component
More informationDigital Modulator Instructions
Product Code: CCT818 ANTIhum.com Digital Modulator Instructions Features Tunable output channel from 21-69, Push button channel selection, Microprocessor tuning, Channel Memory, Audio input, LED channel
More information1-Touch Vibratory Sieve Shaker SS-10
1-Touch Vibratory Sieve Shaker SS-10 Safety Instructions WARNING!! This machine operates on electric current. Improper operation could result in electrical shock, electrocution, or an explosion! 1. ALWAYS
More informationDREAMOC DIAMOND 4K - ASSEMBLY GUIDE VERSION ORIGINAL ASSEMBLY GUIDE
DREAMOC DIAMOND 4K - ASSEMBLY GUIDE VERSION 1.2 - ORIGINAL ASSEMBLY GUIDE It is important to read this assembly guide before using the Dreamoc Diamond, and to follow advices and instructions on safety,
More information"shell" digital storage oscilloscope (Beta)
"shell" digital storage oscilloscope (Beta) 1. Main board: solder the element as the picture shows: 2. 1) Check the main board is normal or not Supply 9V power supply through the connector J7 (Note: The
More informationMOD028 GLOCKENSPIEL TECHNO-MUSIC-OLOGY
MOD028 GLOCKENSPIEL TECHNO-MUSIC-OLOGY MOD028 - Techno-music-ology Kit Contents Motor Controller PCBs 14 220R (red red brown gold) resistors 2 330R (orange orange brown gold) resistors 16 1N4001 diodes
More information