FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N

Size: px
Start display at page:

Download "FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N"

Transcription

1 FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N 24 Address Point Fibre distribution point (FDP) Installation guide for fibre DP Contents 1 Kit Contents 2 Accessories 3 MOBRA installation 4 Looped cable installation 5 Heatshrink installation 6 Fibre routing 7 Closing the closure 8 Quality checks 9 Cable cutting templates 10 Port layout and preferred port usage General description Fibre Distribution Point (FDP) for use in the Fibre to the Premises network. The underground 24 Address Point Fibre Distribution Point (24FDP) distributes the fibres from Blown Mini-Cable to each of 20 Address Points via 12 or 7 Blown Fibre Tube. The closure has trays for fibre storage. These instructions detail the Plan & Build activity for the 24 address point FDP only. For Lead to Cash activity please refer to ISIS EPT/COF/D891. Note: an upgrade kit is required for FDPs (Tyco Electronics description FIST-GCO2-OTIAN-FDP- SOA7) to allow the fitting of Fibre locking spirals. WARNING: Appropriate personal protection equipment shall be used at all times. Pictures in this instruction show un-gloved hands for clarity only. BT Safety procedures and working practices must be followed at all times.

2 1 Kit content Dome Base including metal frame groove plates and trays. O-ring Installation instruction 2 Accessories Mobra Mobra plate TBC Circular port kit 3A Oval port kit 3A Heat protection kit (SCOP) Loop insert tool 3A Closure sealant 10B Gun Mastic Heavy Duty ) Stripper cable sheath No11A TBC Cutter cable hand No 5A D nozzle FTTP FDP port opening cord Stayguard 2A (yellow) pack of A number of Mobra options exist for this closure when used in a Joint box. Follow the mounting installation instructions supplied with the Mobra. 3.1 Instructions below are for a No Drill Mobra in a Joint Box 2 and are given as an example. A Cable minimum bend radius Minimum bend radius for COF205 = 125mm. Minimum bend radius for 2.7/6.0mm blown fibre tubing = 72mm. Minimum bend radius, blown fibre tube 7-way ( mm) tubes = 185mm. Minimum bend radius, blown fibre tube 12-way ( mm) tubes = 237mm. B 3.2 The correct position for the edge of the nylon foot is 20mm down from the frame and touching the rear wall, as shown above. 3.3 Using 2 x 24 mm spanners (one on nut A, the other on nut B). Holding the Mobra in the required position, use 2 x 24 mm and adjust nut A to tighten the Mobra in position. 2

3 Locking pin 3.6.The FDP is attached to the FDP Mounting Bracket which is then attached to the Mobra arm and secured with the locking pin. C 4 Looped Cable Installation 4.1 COF 205 Loop Lengths to be left by cabling party, duct mouth to duct mouth 3.4 The swivel (C) can be positioned on the pivot bar by sliding to the left or right. Warning, do not stand on the MOBRA Length for Box type AN/SPN Length for FDP JUF 2 N/A 6.7 m JUF m 8.3 m JUF m 9.5 m JUF m 13.0 m Note: 3.8 m loop inside joint 3.5 Attach the mounting plate onto the closure. Position the closure on the MOBRA. Warning: Do not overtighten bolts or else permanent damage to the closure base will result. 3

4 4.2 Use FDP port opening cord to open the oval port. Note, Refer to section 10 for port usage. Note: port numbers are moulded into the closure. Allowing for a 3.8m loop inside the closure, mark the centre of the loop and strip 1.9mts each side. Distribution side cable Exchange side cable 4.3 Assemble the strength member clamps on the plate as shown. 4.5 Take the loop insert tool 3A and form the element tubes gently over it. Push the element tubes in the sleeve. The non coated edge of the sleeve (arrow) should be pointed towards the base of the closure. Ensure cable tie ratchet blocks are positioned this side of cable Exchange side cable 4.4 Referring to template in section 9 use Cutter Cable Hand 5 to cut both strength members, clean and abrade cables before installing SCOPs and protection foils. Note: foils have sharp edges, please use with care. Smooth the cable protection foil with a blunt tool. Insert the strength members into clamps and secure using allen key supplied with the port kit & secure cable with tie wraps. 4.6 Still using the loop insert tool pass the tubes through the oval port. 4

5 5 Heatshrink Installation 5.1 Oval port Note, threaded spacers this side Note, threaded spacers this side 4.7 Install onto the bracket in the oval port and secure with the split pin, open the split pin Push heatshrink tubing to top of cable port adjacent with closure base. Insert the 3 fingered clip between the cables. Using a D nozzle start shrinking the tube from the top, continue shrinking and converting the paint until the heat shrink is fully shrunk down. Lightly tape the cables together to prevent them moving during the cooling period. Note: use the heat-shield as required to protect occupied and unoccupied ports whilst shrinking the port seal. 4.8 Store looped elements in the plastic sleeve supplied and store in the dedicated area. Warning; Ensure that any working fibre elements have been positioned behind the loop Allow the sleeve to cool for approx 10 minutes before moving. Quality check, all paint converted and a visible flow of adhesive from the clip and at the end of the sleeve Fill the oval port with Closure Sealant 10B, this provides the required strength for mini cable in the port. 5

6 5.2 BFT 7 and BFT 12 installation in a Joint box 2 Note, the installation of the flexible tubing shown below is for use in JB2 boxes only The above drawing shows two BFT 12s bundles entering a JB 2 from opposite directions, both BFTs have their sheaths removed and replaced with flexible tubing between points A-A and B-B to protect the individual tubes. The length of flexible tube used for A-A is 1380mm The length of flexible tube used for B-B is 900mm. Note, flexible tubes AA & BB are shown in two different shades for clarity. 5.3 Installation of BFT (AA & BB) Offer the BFT to the FDP (in the working position) ensuring good routing in the joint box. Cut here All exposed COF 205 must be protected with two pieces of Stayguard 2A yellow intertwined as shown in the picture above. Note: Only one cable shown protected for clarity Mark the BFT at a point such that there will be approx 100mm inside the FDP (the100mm will later be trimmed to the required working length inside the FDP). Cut the cable at this point and remove the surplus. 6

7 For BFT installation in all other Joint boxes. 250 mm Remove the BFT sheath to a point 250mm from the duct mouth Replace the sheath with the required length of flexible tube as shown in Join the flexible tubing to the BFT cable using a heat shrink port seal kit. Insert the cable sheath into the flexible tubing by 50mm. Then apply foils as shown in Remove 100 mm of BF tubing sheath. Clean and abrade the BF tubing sheath for a length of 220mm from the cable butt. Position cable protection foils for cables as shown in the templates. Note: foils have sharp edges, please use with care. Smooth the cable protection foil with a blunt tool Use a conventional circular port shrinkdown kit, with foils, to secure the flexible tube onto the cable sheath, ensuring the sleeve is central over the flexible tube /BFT sheath Ensure the flexible tube extends 20mm into the required FDP circular port at the FDP. Use a circular port shrinkdown kit with foils to secure the flexible tube in position Pass cable through heat shrink sleeve. Position cable so as the blue line is at the bottom of the heat shrink tube. See template in section 9 and position heat-shield as required to protect ports. 7

8 Note: ensure the ARROW on the sleeve points towards the base. The sleeve will not milk off if this is done. Position heat-shield & using a D nozzle start shrinking the tube from the top, continue shrinking and converting the paint until the heat shrink is fully shrunk down. Allow the sleeve to cool for approx 10 minutes before moving. Quality check, all paint converted and a visible flow of adhesive at the end of the sleeve. Note. Fill the port with Closure Sealant 10B, this provides the required blocking of the cable in the port Install the BFT into the appropriate port as per section 10. This picture shows a BFT 12 installed into port When the resin is set, mark and cut all the 4mm tubes at 50mm above the resin Fill the port with Closure Sealant 10B, this provides the required blocking of the cable in the port Ensure all tubes are capped with 4mm end caps. 8

9 6 Fibre routing 6.1 From loop storage remove the elements, select the element required, cut element at the mid point. Route the selected element to the element tube holder, mark & remove element tube to expose the fibres from this point. 6.3 On the required HCSC tray open tray 2 to allow routing onto tray Install insert into tube holder to hold element(s) in place. Store all remaining elements in loop storage. Route the fibres up the left hand channel. 6.4 Route fibre to inner track for tray 1 as shown, store fibre on the tray, ensure fibre is stored under all tabs including the bar code tab. Check fibres are correctly retained and close tray 2 onto tray 1 9

10 Routing Fibre onto High Capacity Single Circuit (HCSC) top Tray 2. Route fibre to outer track for tray Route fibre to outer track for tray Route fibre to hinge, pass fibre through hinge and store fibre on tray, ensure fibre is stored under all tabs including the bar code tab. Check fibres are correctly retained. 10

11 7 Closing the closure 7.2 Closing the latches. 7.3 Use the nylon securing band around the centre of the closure to hold the closure in place. 8 Quality checks Heat shrink port seals installed with arrow UP, paint converted & visible flow of adhesive from end of sleeve Minimum bend radius of cables & fibres maintained Fibre joint & cables labelled correctly. Cable preparation, fibres thoroughly de-greased Fibres clearly identified, routed & stored correctly Check that closure sealant 10B has been used where required as stated in these instructions. 7.1 Ensure all tubes/fibres are secured inside the closure before and during fitting of the dome. To ensure correct orientation of the dome/base ensure the moulded arrows align. Arrows are highlighted in white in picture for clarity. In addition to the above quality checks, the checks detailed in ISIS EPT/ANS/A047 FTTP Quality Standards & Checks shall be complied with. 11

12 9 Cable preparation templates 12

13 13

14 14

15 10 Port layout and preferred port usage The FDP base plate is illustrated below. To keep the tube routing within the FDP tidy the Port/Cable/FLS combinations in the Table shall be used. The FDP port base layout, (viewed from INSIDE the joint). Table indicating preferred port and FLS usage sequence 15

16 Tyco Electronics UK Ltd. Faraday Road Dorcan, Swindon Wiltshire SN3 5HH Tel.: Fax: FIST, TE (logo) and TE Connectivity are trademarks of the TE Connectivity group of companies and its licensors. While TE Connectivity and its affiliates referenced herein have made every reasonable effort to ensure the accuracy of the information contained in this catalog, TE Connectivity cannot assure that this information is error free. For this reason, TE Connectivity does not make any representation or offer any guarantee that such information is accurate, correct, reliable or current. TE Connectivity reserves the right to make any adjustments to the information at any time. TE Connectivity expressly disclaims any implied warranty regarding the information contained herein, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose. TE Connectivity only obligations are those stated in TE Connectivity Standard Terms and Conditions of Sale. TE Connectivity will in no case be liable for any incidental, indirect or consequential damages arising from or in connection with, including, but not limited to, the sale, resale, use or misuse of its products. Users should rely on their own judgment to evaluate the suitability of a product for a certain purpose and test each product for its intended application. 16 TC 921/SIP/UK/2 08/11

3A TC 699/SIP/UK/12

3A TC 699/SIP/UK/12 Hybrid OTIAN Node I N S T A L L A T I O N I N S T R U C T I O N Generic Joint 3A - Item Code 006825 TC 699/SIP/UK/12 07/15 - Helpline 01793 572453 Contents 1 General description 2 Capacity 3 Kit contents

More information

3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes

3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24

More information

FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block

FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block FOSC-450D I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories 2.4 Capacity 3 Preparation of the closure 4

More information

FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N

FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N In-line and butt version Cold applied re-usable fiber optic closure Contents 1 Introduction 1.1 Product description 1.2 Capacity 2 General

More information

2179-CD Series Fiber Optic Splice Closure. Installation Instructions

2179-CD Series Fiber Optic Splice Closure. Installation Instructions 2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal

More information

2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table

2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table FIST-GCO2-F INSTALLATION INSTRUCTION GCO2-FC GCO2-FD Content 1 Introduction 2 General 2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table 3 Installation

More information

Medium Box for Cable Termination

Medium Box for Cable Termination FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling

More information

FOSC 450 C6 and D6 Closures

FOSC 450 C6 and D6 Closures FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel

More information

FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays

FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays FIST-MB2-S I N S T A L L A T I O N I N S T R U C T I O N FIST Medium Box for Cable Splicing Only Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and

More information

FIST-GCO2 GCO2-BC8 GCO2-BD8 GCO2-BE8 GCO2-BF8. 5 Heatshrink installation. 1 Introduction. Content. 6 Fiber routing. 2 General. 7 Fiber routing on tray

FIST-GCO2 GCO2-BC8 GCO2-BD8 GCO2-BE8 GCO2-BF8. 5 Heatshrink installation. 1 Introduction. Content. 6 Fiber routing. 2 General. 7 Fiber routing on tray FIST-GCO2 I N S T A L L A T I O N I N S T R U C T I O N GCO2-BC8 GCO2-BD8 GCO2-BE8 GCO2-BF8 Content 1 Introduction 2 General 2.1 Abbreviation 2.2 Kit Contents 2.3 Elements needed from the FIST installation

More information

3 SLiC Aerial Closure with Rubber End Seal

3 SLiC Aerial Closure with Rubber End Seal 3 Aerial Closure with Rubber End Seal Instructions 1.0 General 1.1 This instruction bulletin describes the assembly of the 3M Aerial Closure with external bonding hanger brackets. These closures are suitable

More information

FIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.

FIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements. FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories

More information

SLiC Fiber Aerial Closure System

SLiC Fiber Aerial Closure System 3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine

More information

3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR

3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR 3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR Instructions July 2010 78-8135-0094-5-K 3 1.0 General 1.1 3M Fiber Optic Splice Closure 2178-XSB The

More information

3M Distribution Box (DDB)

3M Distribution Box (DDB) 3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure

More information

Ordering Guide of the Fiber-Optic Splice Closure (FOSC-400)

Ordering Guide of the Fiber-Optic Splice Closure (FOSC-400) Page 1 of 11 Ordering Guide of the Fiber-Optic Splice Closure (FOSC-400) This document provides assistance with the selection of FOSC-400 closures. It includes the following sections: 1 Product description

More information

Ordering Guide. for FIST-GCO2 product range

Ordering Guide. for FIST-GCO2 product range Ordering Guide for FIST-GCO2 product range Page 1 of 18 Ordering Guide of the Generic Closure Organizer (FIST-GCO2) This document provides assistance with the selection of FIST Generic Closure Organizers

More information

GCO2-BC6/16-MC-XV GCO2-BD6/16-MC-XV GCO2-BE6/16-MC-XV. 3.1 Installation of the workstand 3.2 Opening the FIST-GCO2

GCO2-BC6/16-MC-XV GCO2-BD6/16-MC-XV GCO2-BE6/16-MC-XV. 3.1 Installation of the workstand 3.2 Opening the FIST-GCO2 FIST-GCO2-BX6/16-MC I N S T A L L A T I O N I N S T R U C T I O N GCO2-BC6/16-MC-XV GCO2-BD6/16-MC-XV GCO2-BE6/16-MC-XV Content 1 Introduction 2 General 2.1 Abbreviation 2.2 Kit Contents 2.3 Accessories

More information

GCO2-BC6/16-XX GCO2-BD6/16-XX GCO2-BE6/16-XX

GCO2-BC6/16-XX GCO2-BD6/16-XX GCO2-BE6/16-XX FIST-GCO2 INSTALLATION INSTRUCTION TC-574-IP Rev A, Feb 2017 www.commscope.com GCO2-BC6/16-XX GCO2-BD6/16-XX GCO2-BE6/16-XX Content 1 Introduction 2 General 2.1 Abbreviation 2.2 Kit Contents 2.3 Elements

More information

18mm ECAM Cable Entry Port

18mm ECAM Cable Entry Port 18mm ECAM Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 18mm ECAM (External Cable Assembly Module) Cable Entry Port Kit is designed to accept fiber optic cables with external diameters

More information

Ordering Guide of the Generic Closure Organizer (FIST-GCO2)

Ordering Guide of the Generic Closure Organizer (FIST-GCO2) Page 1 of 18 Ordering Guide of the Generic Closure Organizer (FIST-GCO2) This document provides assistance with the selection of FIST Generic Closure Organizers (FIST-GCO2) for use in FIST applications.

More information

3M Better Buried Closures

3M Better Buried Closures 3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...

More information

Installation Instructions

Installation Instructions TECP-30-260 Issue 2 July 2016 Installation Instructions OWB-S OWB-S Small Wall-mounted Box CONTENTS 1. Introduction 2. Kit content 3. Installation Instruction 3.1. Box installation 3.2. Conduit installation

More information

2178-L/S Series Fiber Optic Splice Case with Gasket

2178-L/S Series Fiber Optic Splice Case with Gasket 2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents

More information

3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket

3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket For use with 3M SLiC Free-Breathing Fiber Optic Closures and Terminals Instructions November

More information

Instructions. Cable with Armor F CAUTION. October Rev A

Instructions. Cable with Armor F CAUTION. October Rev A 3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables

More information

3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882)

3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882) 3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462FN and 3M High Gel Reenterable Encapsulant 8882) Instructions April 2016 78813509979C Contents: 1.0 General... 1 2.0 Kit Contents...

More information

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions September 2017 78-8130-5055-2-M 2 September 2017 78-8130-5055-2-M 1.0 Kit Contents 2.0 General...

More information

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR 3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions July 2010 3 1.0 Contents 1.0 General...3 2.0 Kit Contents...3 3.0 Cable Preparation...4 4.0

More information

SJOF-BS604B. Fiber Optic Splice Closure User Manual Rev.1

SJOF-BS604B. Fiber Optic Splice Closure User Manual Rev.1 Fiber Optic Splice Closure 1. Introduction 1.1 General SAMJIN s SJOF-BS604B protects fiber optic splicing point in various installation conditions such as aerial, manholes, ducts, wall and direct buried

More information

24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual

24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number

More information

3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series

3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series 3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series Instructions Voltage Rating: 1000 V, Temperature Rating: 90 C Kit Contents 78-R1 78-R2 78-R3 78-R4 78-R5 Sleeve Set 1 1 1 1

More information

High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions

High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions High Density Block BRCP HD BRCP- 128/192/256 pair Installation Instructions Product Introduction The BRCP block is the latest generation of MDF terminal blocks developed by 3M, specifically designed for

More information

Ordering Guide. for FIST-GSS2 product range

Ordering Guide. for FIST-GSS2 product range Ordering Guide for FIST-GSS2 product range Page 1 of 17 Ordering Guide of the Generic Splicing Shelf (FIST-GSS2) This document provides assistance with the selection of shelves for use in FIST cable termination

More information

3M Fiber Optic Wall Mount Enclosure 8430 Series

3M Fiber Optic Wall Mount Enclosure 8430 Series 3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6

More information

2178 Fiber Optic Splice Case and 2181 Cable Addition Kit

2178 Fiber Optic Splice Case and 2181 Cable Addition Kit 2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice

More information

FOSC 400. Ordering Guide For Closures and Accessories. Section I 3. Section II 5. Section III 9. Section IV 11. Section V 15

FOSC 400. Ordering Guide For Closures and Accessories. Section I 3. Section II 5. Section III 9. Section IV 11. Section V 15 FOSC 400 Ordering Guide For Closures and Accessories Section I 3 How to Order FOSC 400 Closures Section II 5 How to Order Accessories for FOSC 400 Closures Section III 9 Other FOSC Fiber Optic Splice Closures

More information

NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM

NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM Content 1. General 5 2. The products of NC-1000 system 6 3. Mounting of the frame 8 4. Earthing of the frame 8 NC-1000 FIBRE OPTIC

More information

FOSC 400 A4 Fiber Optic Splice Closure

FOSC 400 A4 Fiber Optic Splice Closure FOSC 400 A4 Fiber Optic Splice Closure I N S T A L L A T I O N I N S T R U C T I O N 1. General Product Information This installation practice provides instructions for installing Tyco Electronics FOSC

More information

3M Better Buried Compound Compression Closure System

3M Better Buried Compound Compression Closure System 3M Better Buried Compound Compression Closure System Instructions March 2016 78-0015-2948-2-A Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 Closure Selection Guide...4 4.0 LHS End Cap Installation...5

More information

HCS - HES Cabling Systems

HCS - HES Cabling Systems HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the

More information

Sections 1. Application Equipment 2. Cable Preparation 3. Assembly 4. Termination Procedure 5. Inspection 6. Repair 7.

Sections 1. Application Equipment 2. Cable Preparation 3. Assembly 4. Termination Procedure 5. Inspection 6. Repair 7. Page 1 of 6 Coaxial SolderSleeve Termination with Pre-Installed Wires or PCB Termination Body, B-044, B-043, B-041, B-040, B-020, B-021, B-046, D-148 Series Cable Type Typical RG Cable # -A- RG 178 RG

More information

3 Foam Sealed Closure 2" (50 mm) with Compound Compression

3 Foam Sealed Closure 2 (50 mm) with Compound Compression 3 Foam Sealed Closure 2" (50 mm) with Compound Compression Instructions 1.0 General 1.1 The 3M Foam Sealed Closure is designed to be used in the construction and maintenance of buried and underground PIC

More information

RAIL D-SUB BACKSHELLS

RAIL D-SUB BACKSHELLS RAIL D-SUB BACKSHELLS FOR D-SUBMINIATURE CONNECTORS D-SUB BACK SHELLS /// DATA SHEET RAIL D-SUB BACKSHELLS FOR D-SUBMINIATURE CONNECTORS TE Connectivity (TE) provide a comprehensive range of ruggedized

More information

COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x cm cm x cm)

COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0 x 22 8.5 x 22 (15.24 cm x cm cm x cm) OCTOBER 2004 COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x 55.88 cm 21.59 cm x 55.88 cm) Be sure to read and completely understand this procedure before applying

More information

CONNECTING THE FUTURE 19" LINXS LIGHTWAVE INTEGRATED CROSS-CONNECT SYSTEM USER MANUAL

CONNECTING THE FUTURE 19 LINXS LIGHTWAVE INTEGRATED CROSS-CONNECT SYSTEM USER MANUAL CONNECTING THE FUTURE 19" LINXS LIGHTWVE INTEGRTED CROSS-CONNECT SYSTEM USER MNUL 109003 Issue Rev 2 19" Lightwave Integrated Cross-Connect System (LINXS) User Manual Document Number 109003 Issue Rev 2

More information

OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation

OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation OFDC-B8-72 I N S T A L L A T I O N I N S T R U C T I O N Outdoor fiber distribution closure Content 1 Introduction 2 Kit content 3 Closure preparation 4 Cable preparation 4.1 Feeder cable 4.2 Drop cable

More information

Gel-sealed in-line fiber optic closure

Gel-sealed in-line fiber optic closure SCIL-C Gel donut INSTALLATION INSTRUCTION TC-1363-1-IP Rev A, Oct 2017 www.commscope.com Gel-sealed in-line fiber optic closure Contents 1 General 2 Sizing and product kit information 3 Installation conditions

More information

3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT

3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT 3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT For Tape Over Wire (TOW) and Wire-Over-Tape (WOT) Shielded Cable For 250 2000 kcmil cable with 650-mil primary insulation thickness Instructions

More information

IP-LINX. Installation Guide

IP-LINX. Installation Guide Installation Guide Installation Guide, 146653-4 Copyright 2017, Telect, Inc. All Rights Reserved Telect and Connecting the Future are registered trademarks of Telect, Inc. 22425 East Appleway Ave. # 11

More information

27mm ECAM Double Cable Entry Port

27mm ECAM Double Cable Entry Port 27mm ECAM Double Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 27mm ECAM Double Cable (External Cable Assembly Module) Entry Port is designed to accept fiber optic loose tube & central

More information

TFT-150R-G. Tape Shield Cable (page 2) Suggested Installation Equipment (not supplied with kit) Wire Shield Cable (page 7)

TFT-150R-G. Tape Shield Cable (page 2) Suggested Installation Equipment (not supplied with kit) Wire Shield Cable (page 7) TFT-150R-G 5-15kV Cold Applied Indoor (5-8kV Indoor and Outdoor) Termination for Copper Tape, Wire Shield, Lead Sheath, and UniShield Cable Suggested Installation Equipment (not supplied with kit) Cable

More information

3M Fiber Closures BPEO

3M Fiber Closures BPEO 3M Fiber Closures BPEO 2 3M Fiber Closures BPEO The 3M Fiber Closures BPEO are designed with flexibility in application in mind. With a range of sizes, they can be deployed above grade (pole, facade) or

More information

Ordering Guide of the Generic Closure Organizer (FIST-GCO2)

Ordering Guide of the Generic Closure Organizer (FIST-GCO2) Page 1 of 26 Ordering Guide of the Generic Closure Organizer (FIST-GCO2) This document provides assistance with the selection of FIST Generic Closure Organizers (FIST-GCO2) for use in FIST applications.

More information

3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter

3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter Instructions January 2010 3 1.0 General 1.1 The 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter(s) protects, organizes and stores

More information

Installation instructions Roxtec RM ES B

Installation instructions Roxtec RM ES B Installation instructions Roxtec RM ES B Environmental side Termination/ interior side Pipe Cable screen/armor Layers Termination/ interior side Cable sheath Layers Environmental side Vertical screen Plastic

More information

IP-LINX Fiber :: X-XXXX

IP-LINX Fiber :: X-XXXX Fiber :: 055-797X-XXXX User Manual Telect, Inc. All rights reserved. 146653-A0 Table of Contents Chapter 1: Introduction...3 1.1 Tools Required...3 1.2 Additional Parts...3 1.3 Assemblies...3 Chapter 2:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS LIGHTGUARD 350-20-WTC SEALED FIBER OPTIC CLOSURE VIEW ONLINE TABLE OF CONTENTS: GENERAL...2 SPECIFICATIONS...2 PACKAGE CONTENTS...3 PACKAGE CONTENTS: ACCESSORIES...3 RECOMMENDED TOOLS...3 ADD-ON COMPONENTS...4

More information

FOSC 400 B2/B4. Fiber Optic Splice Closures. Table of Contents. Page 1

FOSC 400 B2/B4. Fiber Optic Splice Closures. Table of Contents. Page 1 FOSC 400 B2/B4 I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closures Table of Contents Page 1. General Product Information 2 2. Warnings 3 3. Required Tools and Materials 3 4. Standard

More information

3M Cold Shrink Splice Kit QS-III 5514A

3M Cold Shrink Splice Kit QS-III 5514A 3M Cold Shrink Splice Kit QS-III 5514A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

3M Cold Shrink Splice Kit QS-III 5515A

3M Cold Shrink Splice Kit QS-III 5515A 3M Cold Shrink Splice Kit QS-III 5515A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

Quante BPEO Splice-Protection Closure for Optical Fiber Cables. Features Advantages Benefits

Quante BPEO Splice-Protection Closure for Optical Fiber Cables. Features Advantages Benefits 3 Quante BPEO Splice-Protection Closure for Optical Fiber Cables BPEO: Fully Mechanical, Easy to Install, No Specific Tools BPEO is the newest generation of watertight spliceprotection closures for optical

More information

Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL

Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std. 404 35 kv Class 250 kv BIL Kit Number 5798A-MT Cable Range Requirements Cable Insulation O.D.

More information

Installation instructions Roxtec RM PE B

Installation instructions Roxtec RM PE B Installation instructions Roxtec RM PE B Environmental side Termination/ interior side Pipe Cable screen/armor Layers Termination/ interior side Cable sheath Layers Environmental side Plastic film Conductive

More information

3M Coupling Tray FDTC-10S-COUPLINGTRAY

3M Coupling Tray FDTC-10S-COUPLINGTRAY 3M Coupling Tray FDTC-10S-COUPLINGTRAY for use with 3M Fiber Dome Closures FDC 10S Instructions July 2010 3 1.0 Introduction The 3M Coupling Tray FDTC-10S-COUPLINGTRAY can accommodate up to 10 loose tubes.

More information

SLiC Fiber Aerial Closure 533 and 733

SLiC Fiber Aerial Closure 533 and 733 SLiC Fiber Aerial Closure 533 and 733 3M s SLiC fiber aerial closures are designed to enable service providers to costeffectively deploy aerial fiber networks in the access network (FTTN, HFC, and FTTP).

More information

3. Electronics and MMU2 unit assembly

3. Electronics and MMU2 unit assembly Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 34 Step 1 Tools necessary for this chapter Please prepare tools for this chapter: 2.5mm Allen key for M3 screws 2mm Allen key for nut alignment

More information

3M Cold Shrink Foldback Splice Jacket Kit

3M Cold Shrink Foldback Splice Jacket Kit 3M Cold Shrink Foldback Splice Jacket Kit SJ-FB Instructions! CAUTION Working around energized systems may cause serious injury or death. Installation should be performed by personnel familiar with good

More information

PEM1124ENG ENGLISH. STK TERMINATION KIT FOR PLASTIC CABLE WITHOUT ARMOURING 1 kv STKR TERMINATION KIT FOR PLASTIC CABLE WITH ARMOURING 1 kv

PEM1124ENG ENGLISH. STK TERMINATION KIT FOR PLASTIC CABLE WITHOUT ARMOURING 1 kv STKR TERMINATION KIT FOR PLASTIC CABLE WITH ARMOURING 1 kv INSTALLATION INSTRUCTION PEM1124ENG 2010-05 STK TERMINATION KIT FOR PLASTIC CABLE WITHOUT ARMOURING 1 kv STKR TERMINATION KIT FOR PLASTIC CABLE WITH ARMOURING 1 kv ENGLISH 4 CORE 3+1 CORE 2/8 PEM1124ENG

More information

3M Fiber Optic Splice Closure 2178-L/S Series with Gasket

3M Fiber Optic Splice Closure 2178-L/S Series with Gasket 3M Fiber Optic Splice Closure 2178-L/S Series with Gasket Instructions for: 3M Fiber Optic Splice Closures 2178-L/S Series 3M Flame Retardant Fiber Optic Splice Closures 2178-L/S/FR 3M Cable Addition Kit

More information

FOSC 400 C5 & D5 Fiber Optic Splice Closures

FOSC 400 C5 & D5 Fiber Optic Splice Closures FOSC 400 C5 & D5 Fiber Optic Splice Closures I N S T A L L A T I O N I N S T R U C T I O N 1. General Product Information The FOSC 400 C5 and D5 closures are combination cable closures and splice organizers,

More information

Coyote popup display set up instructions

Coyote popup display set up instructions Coyote popup display set up instructions Frame 1 2 3 Prepare frame for assembly by locating the purple hooks on top of the frame. Stretch frame to size, snapping magnetic locking arms together. Attach

More information

3M Cold Shrink Splice Kit QS-III 5416A

3M Cold Shrink Splice Kit QS-III 5416A 3M Cold Shrink Splice Kit QS-III 5416A for Jacketed Concentric Neutral (JCN) and Concentric Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized systems may

More information

LEGEND POWER SYSTEMS

LEGEND POWER SYSTEMS S HEAT SHRINK JOINT 11kV 3 CORE Armoured XLPE/EPR Copper Wire screens STRAIGHT JOINT LEGEND POWER SYSTEMS Date 11 November 2014 Instruction Number PJJ006-14C PJJ006-14C Page 1 of 10 HEAT SHRINKABLE JOINT

More information

Optical Distribution Box 300 Installation Guide. Version : R0.0

Optical Distribution Box 300 Installation Guide. Version : R0.0 Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be

More information

FOSC-450 Product Range Ordering Guide

FOSC-450 Product Range Ordering Guide of the Gel Sealed Splice Closure (FOSC-450) 1 Product description 2 2 Ordering information 3 2.1 Basic FOSC closures 3 2.2 FOSC closure accessories 4 3 Product guide 5 3.1 Closure description 5 3.2 Closure

More information

Rotor Blade Protection Kit 8999K11

Rotor Blade Protection Kit 8999K11 3 Rotor Blade Protection Kit 8999K11 June 2010 Product Description The components in this kit may be used to protect the leading edge of rotor blades on heavy lift helicopters. This application uses 8-inch

More information

Fiber Optic Splice Closure GPJ Instruction Manual. [Escribir texto]

Fiber Optic Splice Closure GPJ Instruction Manual. [Escribir texto] Fiber Optic Splice Closure GPJ09-8205 Instruction Manual [Escribir texto] 0 Table of Contents 1. General Introduction 2 2. Specification 2 3. Structure 2 4. Installation instructions. 4 5. Operation procedure.

More information

GF-KSW-48 Series of Fiber Optic Distribution Box. Instruction Manual

GF-KSW-48 Series of Fiber Optic Distribution Box. Instruction Manual Instruction manual GF/KSW/48 Page Nr 1 GF-KSW-48 Series of Fiber Optic Distribution Box Instruction Manual 1. General Introduction GF-KSW-48 series of fiber optic distribution box is applicable to fiber

More information

Quick Release Roof-Mount Kit MB700

Quick Release Roof-Mount Kit MB700 Quick Release Roof-Mount Kit MB700 Owner s Manual Thank you for purchasing a KING product! The KING Quick Release Roof-Mount provides a convenient way to securely mount your KING antenna to your vehicle,

More information

Cold Shrink Straight Joint

Cold Shrink Straight Joint Cold Shrink Straight Joint 3M QS2000E 22 kv Single Core Straight Joint Instruction Sheet All dimensions shown are in mm unless otherwise stated Kits contains components for one single core cable -2-2*

More information

Installation instructions Roxtec RM ES

Installation instructions Roxtec RM ES Installation instructions Roxtec RM ES Environmental side Environmental side Pipe Cable screen/armor Layers Layers Cable sheath Vertical screen Plastic film Conductive tape Integrated environmental sealing

More information

Instruction manual. Midi Fiber Dome. Instruction manual

Instruction manual. Midi Fiber Dome. Instruction manual Midi Fiber Dome Instruction manual Product contents: - 1x Midi Fiber Dome - 1x Window Cut port seal - 1x sealing rubber (long) - 4x sealing rubber (short) - 4x stainless steel screw 4 x 25 T20-6x dummies

More information

K & B Flame Retardant Building Riser Closures

K & B Flame Retardant Building Riser Closures K & B Flame Retardant Building Riser Closures September 1995 Issue 1, 34-7016-7030-8 1. General 1.1 3M Brand K&B Building Riser Closures are designed for use in building riser closets and may be positioned

More information

Tricks of the Trade The Tyco Electronics Brand Raychem is one of the world leading brands in the power cable accessories market. We pioneered heat-shrinkable terminations in the 1960 s, joints in the 1970

More information

SCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :36-29 Sep

SCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :36-29 Sep SCdefault 900 Installation instructions SITdefault Upgrade to Premium 300 sound system MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group

More information

Assembly instructions

Assembly instructions Assembly instructions Model: MXR0024/KIT TV Aerial - 18 Element Kit Contact: Helpline: +44 (0)1553 811000 Email: support@maxview.co.uk Web: www.maxview.co.uk Maxview reserve the right to change specifications

More information

HSK Mine and Portable Cable Splice

HSK Mine and Portable Cable Splice 8096-4-HSK Mine and Portable Cable Splice Instructions 5 and 8 kv rated cables; Type SHD-GC Size 2/0 4/0 (connector max. length 2 1/2") 8096-4-HSK Mine and Portable Cable Splice 78-8119-6296-4-A 1 1.0

More information

DLMP Installation Instructions

DLMP Installation Instructions DLMP Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420 [ ] 2 x

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS MO036A N-HNS (Building Node Cabinet) N-HNS (BUILDING NODE CABINET) Contents Product description Technical data ODF Splice module Cabling organisation Cable/tube/fibre handling

More information

LANmark PCB patch panel, 1HU INSTALLATION GUIDE. LANmark PCB patch panel, 1 HU

LANmark PCB patch panel, 1HU INSTALLATION GUIDE. LANmark PCB patch panel, 1 HU LANmark PCB patch panel, 1HU INSTALLATION GUIDE LANmark PCB patch panel, 1 HU Document information Document reference Release September 2001 Published by Contact address BRO-009 LANmark PP 1HU 0701 Nexans

More information

LGX Compatible (LSX) Connector Module) User Manual)

LGX Compatible (LSX) Connector Module) User Manual) LGX Compatible (LSX) Connector Module) User Manual) 15948-A LSX Connector Module (72-Position Module Shown) Content Page 1 DESCRIPTION... 3 2 DIMENSIONS AND SPECIFICATIONS... 5 3 INSTALLATION... 6 3.1

More information

INSTALLATION GUIDE. LANmark-OF Zone Distribution Box

INSTALLATION GUIDE. LANmark-OF Zone Distribution Box LANmark-OF Zone Distribution Box INSTALLATION GUIDE LANmark-OF Zone Distribution Box Document information Release November 2004 Published by Contact address Nexans Cabling Solutions Alsembergsesteenweg

More information

PEM1126ENG ENGLISH STPKR. TERMINATION KIT FOR PAPER CABLE WITH LEAD SHEATH 1 kv INSTALLATION INSTRUCTION

PEM1126ENG ENGLISH STPKR. TERMINATION KIT FOR PAPER CABLE WITH LEAD SHEATH 1 kv INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION PEM1126ENG 2010-05 TERMINATION KIT FOR PAPER CABLE WITH LEAD SHEATH 1 kv ENGLISH 2/6 PEM1126ENG 2010-05 GENERAL INFORMATION - Check that the kit is suitable for the cable type.

More information

Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier.

Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier. Communication Markets Division 3M Fiber Closures Smart design makes your job easier. 2 Your connections deserve the best protection. No matter the size and configuration of your network, protecting its

More information

4320 SS-25 Self-Strip Terminating Block

4320 SS-25 Self-Strip Terminating Block 4320 SS-25 Self-Strip Terminating Block Instructions May 2002 78-8130-7677-1 1.0 General The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for

More information

Installation instructions Roxtec RM PE

Installation instructions Roxtec RM PE Installation instructions Roxtec RM PE Environmental side Environmental side Pipe Cable screen/armor Layers Layers Cable sheath Plastic film Conductive tape Integrated environmental sealing system for

More information

MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures. 1. General. 2. Precautions

MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures. 1. General. 2. Precautions MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures 004-273-AEN, Issue 2 Table of Contents 1. General.... 1 2. Precautions.... 1 2.1 Cable Handling Precautions...

More information

Fiber Optic Splice Closure GPJ Instruction Manual

Fiber Optic Splice Closure GPJ Instruction Manual Fiber Optic Splice Closure GPJ09-9401 Instruction Manual 1. Brief Introduction GPJ09-9401 type of Fiber Optic Splice Closure is a member in dome series, the main function is to provice direct pass, branch

More information

TECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L

TECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L TECHNICAL GUIDE TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW

More information