15 Marine Satellite System. Model 1200-KU

Transcription

1 15 Marine Satellite System with built-in DVB for positive satellite identification Model 1200-KU Installation and Operating Instructions Satellite Solutions for Mobile Markets Hampshire Avenue South, Bloomington, MN Phone: (800) Fax: (952) MEMBER REV C

2

3 IMPORTANT! The satellite TV market is expanding and changing. The information in this manual was accurate at the time of printing. If your Sea-King does not operate as outlined in this manual please call King Controls at (800) or visit our website at Please read this entire manual before beginning the installation. This Sea-King will not receive channels broadcast from DIRECTV s Ka band satellites at 99 and 103. DISH NETWORKTM - EXPRESSVU: If you plan to use the Sea-King with Dish Network or Bell ExpressVu programming, your receiver must be configured. During the configuration, the antenna must be on the ground, dock or motionless platform with no movement (see Installation Section for complete details). TABLE OF CONTENTS Section Contents Page 1. INTRODUCTION DEFINITION OF TERMS INSTALLATION Tools and Materials Required, Kit Contents Remove Shipping Restraints Dome Location Coax Requirements Pre-Installation Hookup for Initial Search Wiring Schematics Satellite Configuration DISH Network - ExpressVu Check Switch Procedure Dome Installation and External Wiring Internal Wiring OPERATION TROUBLESHOOTING MAINTENANCE LIMITED WARRANTY...31 DIRECTV is a registered trademark of DIRECTV, Inc. Dish NetworkTM is an official trademark of Echostar Communications Corporation. Bell ExpressVu is an official trademark of Bell Canada. DVB is a trademark of the DVB Digital Video Broadcast Project ( ) Page 1

4 SECTION 1 INTRODUCTION The Sea-King 1200-KU Marine Satellite System includes 2 main components (Fig. 1). Dome (Antenna) Unit Controller Mounted on the vessel. The dish is covered by a protective dome that keeps operational components free from the elements. Located in the vessel. Activates the search mode and provides limited diagnostic functions using the status light. Note: A TV, satellite receiver, and program subscription are also required for satellite TV viewing. (Sold separately.) Fig. 1 Note: Overview only. See Installation Section for complete wiring schematic. Page 2

5 SECTION 2 DEFINITION OF TERMS AZIMUTH: Circular rotation around the vessel. Using a clock as reference, the bow of the vessel is 12:00 o clock, and the stern is 6:00 o clock (Fig. 2). Fig. 2 ELEVATION: Angle in degrees measured from a level plane (Fig. 3). Fig. 3 SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission. Page 3

6 SECTION 3 INSTALLATION TOOLS AND MATERIALS REQUIRED drill and drill bit set tape measure 7/16 open end wrench (coax connections) 5/32 allen wrench, channel lock or pliers (to remove shipping bolt) phillips screw driver (to remove dome cover) appropriate fasteners and tools to install all components and wiring adhesive sealant, compatible with vessel material #1844 King Controls Installation and Diagnostic Keypad (may be obtained from an authorized dealer or King Controls) #1844 Diagnostic Keypad KIT CONTENTS 1. Unpack and identify all components (Fig. 4). Fig. 4 Page 4

7 REMOVE SHIPPING RESTRAINTS 1. Remove and save the dome cover screws. (Fig. 5). 2. Carefully remove the dome cover. Do not allow dome cover to catch on internal components or wiring. DO NOT SET THE DOME COVER UPSIDE DOWN. 3. Remove and discard the shipping bolt. Fig. 5 IMPORTANT! The shipping bolt must be removed prior to installation. IMPORTANT! CAREFULLY remove the dome cover. Do not allow dome cover to catch on internal components or wiring. EXTREMELY IMPORTANT! NEVER lift the unit by the LNB assembly, Wave Guide assembly, or the dish. Lift the unit by the base ONLY. Page 5

8 DOME LOCATION 1. Select an area on the vessel for the dome unit, keeping in mind that most times the wiring will enter the vessel through the surface directly beneath the dome unit (see Fig. 7 for typical installations). Use the following criteria: a) The shortest distance between the dome unit and the main satellite receiver is most desirable. b) The dome unit requires a 16.5 diameter mounting area on the vessel surface. You may also use an industry standard mount. (Call King Controls or visit for more information.) Exact hole spacing is shown at right. Distances are to centers of holes. c) The dome unit should never be mounted so that it is tilted more than two degrees in any direction. d) Keep the dome unit as far away from the radar as possible, and if possible above the level of the radar. e) The dome unit should be mounted as close as possible to the center of the vessel (fore-aft and side to side). f) The mounting surface must be strong enough not to flex under the weight of the unit or from vessel vibrations. g) There must be no line of sight obstructions from this location. Items such as masts or radar antennas that are too close to the dome unit may prevent the satellite signal from reaching the dish (Fig. 6). Fig. 6 Page 6

9 Fig KU TYPICAL INSTALLATIONS COAX REQUIREMENTS IMPORTANT! USE ONLY THE COAX CABLE SUPPLIED WITH THE SEA-KING. COIL AND STORE EXCESS CABLE IN THE CABINET WITH THE COMPONENTS. DO NOT CUT COAX. If coax cable other than that supplied with the Sea-King is used, the following guidelines must be followed: 1) Ends must be terminated with SNAP-N-SEAL connectors (Fig. 8). DO NOT USE TWIST-ON OR HEX-CRIMPED CONNECTORS. 2) Cable must be RG6 and rated at 2.2 GHz or higher. Fig. 8 Page 7

10 PRE-INSTALLATION HOOKUP FOR INITIAL SEARCH To verify proper operation of the components, temporarily connect the unit and perform an initial search as follows: 1. Place the dome unit in its mounting location and temporarily secure the unit from falling. Fig. 9 Depending on the location, you may have to use the supplied right angle F-connectors to avoid bending the coax too sharply during the temporary hookup described below (Fig. 9). IMPORTANT! IF CONFIGURING THE RECEIVER FOR MULTIPLE SATELLITE SWITCHING WITH DISH NETWORK OR EXPRESSVU, Y0U MUST DO THE PRE-INSTALLATION CHECK ON A MOTIONLESS PLATFORM SUCH AS THE DOCK OR GROUND. 2. Choose your desired wiring configuration: Dish Network / ExpressVu / DIRECTV (single satellite or auto switching from master receiver only) Fig. 10, Page 9 DIRECTV (auto switching from any receiver) Fig. 11, Page 10 Note: For the temporary hookup and initial testing, plug in the Diagnostic Keypad, not the wall mount controller. 3. TEMPORARILY connect system as outlined. MAKE SURE TO CONNECT POWER LAST. 4. Continue with SATELLITE CONFIGURATION on page 12. Page 8

11 Fig. 10 Dish Network / ExpressVu / DIRECTV Sea-King Model 1200-KU Single satellite (or) multi-satellite with auto-switching from master receiver only Note: HDTV receivers require HDMI or component video/audio cable connection to TV. Page 9

12 Fig. 11 DIRECTV Sea-King Model 1200-KU Multi-satellite with auto-switching from any receiver Note: To automatically switch between satellites using any receiver, tune all other receivers to channel 202 on the 101 satellite. IMPORTANT! Main coax cable must be connected to 18V input on multi-switch. Note: HDTV receivers require HDMI or component video/audio cable connection to TV. Page 10

13 This page intentionally left blank. Page 11

14 SATELLITE CONFIGURATION Satellite re-configuration requires a King Controls Diagnostic Keypad #1844 not supplied with the antenna. If you do not have a keypad, contact your local authorized King-Dome dealer or call King Controls at (800) The Sea-King is factory pre-set for DIRECTV standard digital programming broadcast from the 101 W satellite. If you also receive your local channels from DIRECTV s 119 satellite or if you subscribe to Dish Network or ExpressVu programming, you must use the Diagnostic Keypad to re-configure the antenna to work with your satellite service. Doing this will allow the Sea-King to lock on the correct satellites to receive your programming and also enable automatic satellite switching via the receiver s remote control for multi-satellite service. Antenna configuration is a one time procedure that MUST BE COMPLETED before using your Sea-King antenna. Choose your desired option on pages and then follow the instructions below. DIRECTV SINGLE SATELLITE 101: The system is factory pre-set for basic DIRECTV service broadcast from the 101 W satellite. If you have this service, make sure your receiver is set for round dish-1 satellite (do this through the receiver s satellite set-up menu screens). and then go to page 18. YOU MUST SET YOUR ELEVATION ZONE (PAGE 18) EVEN IF YOU ARE NOT CHANGING YOUR SWITCHING MODE OR PROVIDER CODE. FOR ALL OTHER SERVICES: You will need to change the Satellite Switching Mode and Satellite Provider Code. Determine your SWITCHING MODE and PROVIDER CODE from the chart on page 13 and then follow the instructions on pages Page 12

15 SWITCHING MODE AND PROVIDER CODE CHART Service Satellites Switching Mode Provider Code DIRECTV Single Satellite 101 (Factory Preset) DIRECTV Plus Dish Network Single Satellite 119 Dish 500 (SW21 Switch) Dish 1000 (SW64 Switch) Dish 1000a (SW64 Switch) Bell ExpressVu , , , 119, , 110, Standard Digital HDTV 82/91 82, IMPORTANT: This Sea-King will not receive channels broadcast from DIRECTV s Ka band satellites at 99 and 103. Page 13

16 SATELLITE SERVICE OPTIONS DIRECTV Single Satellite 101 Receive programming from the DIRECTV 101 satellite only. DIRECTV Plus: 101, 119 Automatically switch between the 101 and 119 satellites for DIRECTV. IMPORTANT: This Sea-King will not receive channels broadcast from DIRECTV s Ka band satellites at 99 and 103. BELL EXPRESSVU (May not be available in all areas due to service provider limitations.) Standard Digital 91 Receive programming from the 91 satellite only. HDTV 82/91 Automatically switch between the 82 and 91 satellites for Bell ExpressVu by using the receiver s remote control. Page 14

17 SATELLITE SERVICE OPTIONS DISH NETWORK Single Satellite 119 Receive programming from the 119 satellite only. Dish 500 Automatically switch between the 110 and 119 satellites for Dish Network by using the receiver s remote control. Dish 1000/1000a Dish Network HD programming is broadcast from 4 satellites (61,110,119,129). The 61 and 129 satellites broadcast identical programming. The 61 is generally stronger in the eastern U.S. and the 129 in the western U.S. The map below shows the approximate coverage for each satellite. The Sea-King antenna can be easily configured to work with two different satellite trios (DISH 1000a: 61,110,119 or DISH 1000: 110,119,129). By choosing the appropriate trio that includes either the 61 or the 129 satellite based on where you are, you can receive all of your desired programming. SATELLITES 61 AND 129 COVERAGE MAP Note: This map is an approximation only. Which trio works best in a given location may differ from what is indicated on the map. Page 15

18 Perform the programming on these two pages using the codes you determined from the chart on page 13 (EXCEPT DIRECTV 101 SERVICE - see page 12). SET SATELLITE SWITCHING MODE 1. The Diagnostic Keypad should be plugged in (page 8). If not, unplug the controller and plug in the Keypad. 2. Press ON. 3. Press * 46 # to display the current satellite switching mode. 4. To change the satellite switching mode, press * 96 # * 66 # * 88 # 5. Press the UP and DOWN arrows (2 and 8 keys) to choose the desired switching mode. 6. Press * 47 # to lock in setting. 7. Turn unit OFF and back ON to save setting. 8. Press * 46 # to display and verify code for new satellite switching mode. 9. Continue with SET SATELLITE PROVIDER CODE on next page. Page 16

19 SET SATELLITE PROVIDER CODE 1. Press * 24 # to display the current service provider. 2. To change the current service provider, press * 96 # * 66 # * 88 # 3. Press the UP and DOWN arrows (2 and 8 keys) to choose the desired service provider. 4. Press * 25 # to lock in setting. 5. Turn unit OFF and back ON to save setting. 6. Press * 24 # to display and verify code for new service provider selected. 7. DIRECTV Plus: 101, 119 Set your receiver for oval dish-2 satellites (do this through the receiver s satellite set-up menu screens), then go to page 18. Dish Single Satellite 119 Dish 500 Dish 1000/1000a Bell ExpressVu Standard Digital 91 Bell ExpressVu HDTV 82/91 Go to page 18. Page 17

20 IMPORTANT: YOU MUST PROGRAM IN YOUR CURRENT ELEVATION ZONE EVEN IF YOU DO NOT CHANGE YOUR SWITCHING MODE OR PROVIDER CODE. DIRECTV: SET ELEVATION ZONE AND PERFORM INITIAL SEARCH 1. Determine your elevation zone from the map on page Press * 96 # * 66 # * 88 # 3. Press the UP and DOWN arrows (2 and 8 keys) to display your zone. 4. Press * 44 # to lock in setting. The unit will automatically begin a search and lock on a satellite. When locked, the keypad will display a steady Go to Page 22 and continue with the installation. IMPORTANT: YOU MUST PROGRAM IN YOUR CURRENT ELEVATION ZONE EVEN IF YOU DO NOT CHANGE YOUR SWITCHING MODE OR PROVIDER CODE. DISH NETWORK - EXPRESSVU: SET ELEVATION ZONE AND PERFORM INITIAL SEARCH 1. Determine your elevation zone from the map on page Using the receiver s remote, go to the signal meter screen on the TV and select the 110 satellite and transponder Press * 96 # * 66 # * 88 # 4. Press the UP and DOWN arrows (2 and 8 keys) to display your zone. 5. Press * 40 # to lock in setting. The unit will automatically begin a search for, locate, and verify the selected satellites. (When done, the keypad will display a steady 8 for the left hand digit and alternate between a flashing 0 and flashing 8 for the right hand digit.) 6. Go to page 20 and run the check switch. YOU MUST RUN THE CHECK SWITCH! Page 18

21 ELEVATION ZONE MAP Page 19

22 DISH NETWORK AND EXPRESSVU CHECK SWITCH PROCEDURE IMPORTANT! YOU MUST HAVE COMPLETED THE SET ELEVATION ZONE AND PERFORM INITIAL SEARCH SECTION FOR DISH NETWORK - EXPRESSVU (PAGE 18) BEFORE RUNNING THE CHECK SWITCH. THE DOME UNIT MUST BE ON THE GROUND, DOCK, OR MOTIONLESS PLATFORM WITH NO MOVEMENT. For automatic satellite switching, King Controls recommends using a Dish Network model 311 receiver for Dish 500, and a Dish Network model VIP211 or a VIP211k HDTV receiver for Dish 1000/1000a. Do not use dual tuner receivers or recorders. If you do not have a clear view of the satellites, the switch will not load. Note: The SW21 and SW64 switches are a receiver software configuration that is loaded into the receiver after running a check switch test with the dish locked on and configured for the appropriate service. This one time procedure will not need to be repeated after successful installation, unless a) check switch test is run again while connected to a home dish system, b) check switch is run when a receiver is not connected, or c) you travel outside the coverage area of the pre-set satellite trio (Dish 1000/1000a only). 1. On the receiver remote, press menu, 6, 1, Highlight Check Switch and press select. 3. Make sure Superdish and Alternate boxes are NOT selected. 4. Highlight Test and press Select. Screen graphics may vary. The unit will perform a check switch test, and the dish will periodically move back and forth. (This process will take several minutes.) Page 20

23 5. When test is complete, a screen similar to one of the following should appear: (Screen graphics may vary.) DISH 119 and EXPRESSVU 91 NO SWITCH DETECTED or INSTALLED DEVICE UNKNOWN DISH 500 EXPRESSVU HDTV 82/91 MUST SHOW SW21 NO X s DISH 1000 DISH 1000a NO X s MUST SHOW SW64 If indicated results are not obtained, go back to Step 1 and run test again. Contact King Controls if the check switch fails to load after 4 attempts. 6. Save the settings, exit to the main menu screen and wait for your programming to download. 7. DISH 1000/1000a ONLY: Verify your saved settings show your desired satellite trio (110, 119, 129 or 110, 119, 61). 8. Go to page 22. Page 21

24 When configuration and search are successfully completed, disconnect the unit as follows: a) Turn power off at the keypad. b) Turn power off at the receiver. c) Disconnect power. d) Disconnect coax. DOME INSTALLATION AND EXTERNAL WIRING Fig Apply foam gasket to bottom of dome unit (Fig. 13). Note: The Sea-King is wired for multiple receiver support. There are two coax ports on the bottom of the dome unit. The one labeled MAIN must be connected to the main receiver in the vessel. The unlabeled port can be used for an additional receiver. If using two coax, label the ends of one to avoid confusion when making the internal hookups. The installer is responsible for sealing all openings where wiring enters the vessel so they are entirely waterproof (inside and outside of the holes). IMPORTANT! You must fill the ends of all external coax (including right angle connectors if being used) with the supplied dielectric grease. Failure to do so will void warranty. 2. Connect the 50 coax cable (that will go to the MAIN receiver) to the coax port labeled MAIN on the bottom of the dome unit and tighten connection. MAKE SURE YOU HAVE REMOVED RIGHT ANGLE COAX CONNECTOR UNLESS YOU ARE RUNNING COAX OUT TO THE SIDE. (Fig. 14). If using a second receiver, connect a second coax cable (see coax requirements, page 7) to the unlabeled port and tighten connection. DO NOT OVER TIGHTEN CONNECTIONS (Fig. 14). Page 22

25 Fig. 14 IMPORTANT! Use right angle F-connector ONLY IF ROUTING COAX TO THE SIDE with a direct to deck installation method. Fill ends of F-connectors with grease. IMPORTANT! You must fill the ends of ALL external coax with the supplied dielectric grease. Failure to do so will void warranty. Coax connections should be snug. DO NOT OVER TIGHTEN! 3. Plug external wiring harness into matching connector from dome unit. You must tighten the connection until you feel a click. 4. Route wiring as necessary and place the dome unit in its mounting location. 5. Use the four mounting holes inside the base to install the dome unit to the mounting pedestal or the vessel surface (fasteners go from inside of base to outside). 6. Secure wiring every inches and seal all openings where the wiring enters the vessel so they are entirely waterproof (inside and outside of the holes). IMPORTANT! When re-installing the dome cover, CAREFULLY lower it onto the base. Do not allow it to catch on internal components or wiring. The dome cover screws have a pre-applied locking compound on them. DO NOT APPLY ANY ADDITIONAL LOCKING COMPOUND TO THE SCREWS. APPLYING ADDITIONAL COMPOUND WILL VOID THE WARRANTY AND MAY CAUSE CRACKING IN THE DOME COVER. 7. Replace dome cover on base and align holes in dome cover with holes in base. Attach dome cover with dome cover screws saved earlier. Tighten ALL screws securely. Page 23

26 INTERNAL WIRING 1. Refer back to your desired wiring configuration and make all permanent connections as shown, keeping in mind the following important points: a) For the permanent installation, use the Wall Mount Controller, not the keypad. b) The connection between the dome unit and the receiver must be a direct connection with no devices in between. Any other devices should be downstream from the receiver. Do not go through an A-B or any other switch, box, or booster. c) Power connection must be a non-shared circuit. Excessive current draw on the circuit will cause the unit to operate improperly. Power and ground connections must be made after the wires are connected to the dome unit. Use a 7.5 amp fuse in fused non-shared circuits. FINAL TEST (Follow the Instructions in Section 4, Operation) 1. Perform a search to verify unit is operating correctly. You must be able to view the program guide or a channel. Page 24

27 This page intentionally left blank. Page 25

28 SECTION 4 OPERATION IMPORTANT: There must be a clear line of sight to the southern sky. Masts, antennas, trees, buildings, mountains, etc. can all block the satellite signal from reaching the dish. The distance traveled since last performing a search may affect how long it takes for the Sea-King to find the satellite. This Sea-King will not receive channels broadcast from DIRECTV s Ka band satellites at 99 and 103. Satellite TV and receiver technology are constantly changing. If you experience difficulty go to or contact the King Controls Service Department at (800) , ext Turn on TV and Receiver. Searching for Satellite or similar will appear on TV screen. 2. On Sea-King controller, MOMENTARILY press ON. 3. Press TRACK. STATUS LIGHT alternating colors GREEN-flashing GREEN-steady SYSTEM STATUS Initializing Potential satellite found Target satellite found (tracking) 4. When the status light is steady green, select a channel or the program guide to view your programming. Enjoy! (DO NOT TURN THE SEA-KING OFF.) Note: If the status light is steady GREEN and your programming does not appear, press the reset button on your DIRECTV receiver. If using Dish Network, hold the receiver power button in for 10 seconds to reset your receiver. Consult your receiver owner s manual for further details. (Note that it may take several minutes for the guide to re-download.) When receiver reset is complete and the guide is downloaded, select a channel or the program guide to view your programming. ALTERNATE SEARCH METHOD If you experience difficulty locking onto the satellite, press and hold ON for 3 FULL SECONDS. Page 26

29 AUTOMATIC SATELLITE SWITCHING 1. Simply choose your desired channel using the receiver s remote control. The Sea-King will automatically switch to the appropriate satellite. Note: For better performance when using the automatic satellite switching feature, change channels by selecting your program from the channel guide rather than channel surfing. It is common for the picture to pixel or display an error message when the antenna is switching between satellites, the vessel is pitching or rolling excessively, or the signal has been temporarily blocked. PLEASE BE PATIENT. THE PICTURE WILL RETURN. If an error message appears for an extended period, selecting CANCEL may help clear the message more quickly. Page 27

30 SECTION 5 TROUBLESHOOTING SYMPTOM POSSIBLE REASON COURSE OF ACTION Unit does not find satellite. (STATUS light flashes red or green.) Did not initiate search method correctly. Press ON. Press TRACK. (See OPERATIONS, page 26.) Did not initiate alternate search method correctly. Hold ON/SEARCH button for 3 FULL SECONDS. (See OPERATIONS, page 26.) STATUS light flashes orange. Before search: bad coax connection. After unsuccessful search (approximately 25 minutes): obstruction in line of sight between dome and satellite. Call King Controls. Move vessel to have unobstructed view of southern sky. STATUS light does not stop rapidly flashing red and green. Self check failed: potential motor problem. Call King Controls. STATUS light does not turn on or is dim. Bad power source (low voltage). Bad power or controller cable connection at dome. Bad controller cable connection at controller. Call King Controls. STATUS light is steady green but no picture. Satellite receiver is off or requires reset. Turn receiver on or reset. Page 28

31 CHOOSING A NEW ZONE USING THE WALL MOUNT SWITCH Note: Choose a new zone only if you have traveled a significant distance and are unable to acquire the satellite IMPORTANT! You must complete step 3 within 5 seconds of step Determine the zone you wish to program from the map on page On the wall mount switch, momentarily press ON. 3. The Status light will flash a variety of colors. Watch for it to flash orange, and then red or green. Immediately press ON 3 times. (Note: you must have completed pressing ON 3 times within 5 seconds of Step 2. Status light will flash orange, and then red 4 times. 4 Click ON the same number of times as the LEFT hand digit of the zone (if 0, do not click). Hold the right button DOWN until the status light flashes orange, then release. Status light will flash red 4 times. 5. Click ON the same number of times as the RIGHT hand digit of the zone (if 0, do not click). Hold the right button UP until the status light flashes orange, then release. Status light will flash red 4 times. The new zone is programmed in, and the system will start up and automatically find the satellite. Page 29

32 SECTION 6 MAINTENANCE The Sea-King Satellite System has been designed to be maintenance and trouble free. For optimum signal strength, keep the dome clean from dirt, bugs, and other debris. Periodic washing of the dome with mild soap and water is recommended. If you plan on storing your vessel for long periods of time, it is recommended that the system be put through a search procedure on a quarterly basis to keep all moving parts in good working order. If you have any comments or questions, please contact the King Controls Service Department at (800) , ext. 373, or King Controls at info@kingcontrols.com Rain Fade Rain or dew on the dome can cause signal interference and make the digital picture freeze, pixel or go out altogether. This loss of signal is commonly referred to as rain fade and is caused by the combination of water in the atmosphere and water on the dome surface. To minimize this issue and eliminate the effects of water on the dome, apply King Controls Dome Magic rain fade solution to the dome. This will prevent water from sticking to the dome surface and blocking the signal. For additional details on Dome Magic rain fade solution please contact your authorized Sea-King dealer or call King Controls at (800) Single Application Packet #1830-SP Spray Can #1830 Page 30

33 SECTION 7 LIMITED WARRANTY Every Sea-King Satellite System is thoroughly inspected and tested before leaving the factory. It is covered by a two year parts and one year labor limited warranty from the date of original purchase. This warranty does not cover installation and external wiring or refurbished units. Should any trouble develop during the warranty period, contact King Controls. Only King Controls and certified dealers are authorized to perform warranty evaluations and repairs. If it is determined that the unit needs to be returned, return COMPLETE product, freight prepaid, to : King Controls, Hampshire Ave. S, Bloomington, MN If inspection shows the trouble is caused by defective workmanship or material, King Controls will repair (or at its option, replace) without charge. This warranty does not apply where: The product has been abused, misused, improperly installed or improperly maintained. Repairs have been made or attempted by others that are not certified by King Controls to do such repairs. Repairs are required because of normal wear and tear. Alterations have been made to the product. In no event shall King Controls be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of the warranty. King Controls disclaims liability for any implied warranties, including implied warranties of merchantability and fitness for a specific purpose, after the one year term of this warranty. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Page 31

34 Page 32 Notes:

35

36 11200 Hampshire Avenue South, Bloomington, MN Phone: (800) Fax: (952)