Keyer Control Key Source Fill Source Still Load Still Save Still Freeze User Load Memory...

Transcription

1 1

2 Table of Contents Warnings and Precautions... 4 Warranty... 4 Standard Warranty... 4 Two Year Warranty... 5 Disposal... 5 Packing List... 5 Introduction... 6 Features... 6 System Diagram... 7 Rear Panel... 8 Control Panel Menu Options Start Transition Wipe Border Position Matte Keyer Keyer Keyer Control Key Source Fill Source Chroma P-In-P P-In-P Source Position Border Crop Downstream Key DSK

3 Keyer Control Key Source Fill Source Still Load Still Save Still Freeze User Load Memory Save Memory Inputs Input Crosspoint Setup Outputs Audio GPI Out Standard Frequently-Asked Questions Specifications Dimensions & Weight Service and Support

4 Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit should not be placed in a built-in installation unless proper ventilation is provided. 7. This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. 8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be walked on, rolled over, or otherwise stressed. 9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord rating. 10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15 amperes. 11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill liquid of any kind onto or into this unit. 12. Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself. Opening or removing covers that are marked Do Not Remove may expose you to dangerous voltage points or other risks, and will void your warranty. Refer all service issues to qualified service personnel. 13. Unplug this product from the wall outlet and refer to qualified service personnel under the following conditions: a. When the power cord is damaged or frayed; b. When liquid has spilled into the unit; c. When the product has been exposed to rain or water; d. When the product does not operate normally under normal operating conditions. Adjust only those controls that are covered by the operating instructions in this manual; improper adjustment of other controls may result in damage to the unit and may often require extensive work by a qualified technician to restore the unit to normal operation; e. When the product has been dropped or the cabinet has been damaged; f. When the product exhibits a distinct change in performance, indicating a need for service. Warranty Standard Warranty Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of purchase. The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty. Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this warranty. 4

5 All mail or transportation costs including insurance are at the expense of the owner. All other claims of any nature are not covered. Cables & batteries are not covered under warranty. Warranty only valid within the country or region of purchase. Your statutory rights are not affected. Two Year Warranty All Datavideo products purchased after 01-Oct qualify for a free one year extension to the standard Warranty, providing the product is registered with Datavideo within 30 days of purchase. For information on how to register please visit or contact your local Datavideo office or authorized Distributors Any second year warranty claims must be made to your local Datavideo office or one of its authorized Distributors before the extended warranty expires. Disposal For EU Customers only - WEEE Marking This symbol on the product indicates that it will not be treated as household waste. It must be handed over to the applicable take back scheme for the recycling of electrical and electronic equipment. For more detailed information about the recycling of this product, please contact your local Datavideo office. Packing List The following items should be included in the box. If any items are missing please contact your supplier. 1 x SE-700 unit 1 x Accessory List 5

6 Introduction The Datavideo SE-700 is a small, cost-effective, high quality, HD digital video switcher with easy-to-use professional features. The SE-700 switcher offers two HD SDI and two HDMI inputs with embedded digital audio. Supported video formats include 1080i/50, 1080i/59.94, 1080i/60, 720p/50, 720p/59.94, 720p/60. Output options include; two assignable HD SDI and one HDMI output. These user defined output options can provide Clean PVW, Clean PGM, PGM with DSK overlay, PVW Out or Multi-view as well as Freeze, Still or Inputs 1~4. These SDI or HDMI outputs can be taken to other Datavideo products such as the HRS-30 HD field recorder, TLM-170G HD monitor and also be streamed to web based viewers using the Datavideo NVS-25 Video Streaming Server. The SE-700 also features two Balanced XLR audio inputs for connecting an external audio mixer such as the Datavideo AD-200. Tally and RJ-45 interfaces allow the switcher to be remotely controlled from a Windows PC as well as providing tally light indications to crew and on screen talent via Datavideo s ITC-100 talkback system. When you consider the SE-700 is also capable of HD Chroma Key, Luma Key, Down Stream Key, Picture In Picture, up to 32 Wipe transitions and three user defined Still frame stores it really is a small powerful HD video switcher! Features 4 video inputs ( SDI x 2 + HDMI x 2) - Frame Sync on each input Flexible Mix/Effects Processor with - HD Chroma Key & Linear/Luma Key - Picture-In-Picture supporting Chroma Key & Luma Key Modes as well as a non keyed mode - Wipe Generator with 32 wipe patterns including circle and heart wipes plus Border & Softness Controls - Traditional Mix & Cut Transitions - User defined Down Stream Key for use with external CG text overlay - Full M/E Preview function Frame store - Dedicated Stills Buffer - Up to 500 images can be stored internally - The dedicated Frame Stores allow easy recall of 3 previously loaded images Assignable Outputs (SDI & HDMI) XPT (Cross Point Assignment) On-screen Menu System for quick and easy set up PC control available over RJ45 connection Tally output compatible with Datavideo ITC-100 talk back system GPI Output 6

7 System Diagram 7

8 Rear Panel Power Switch Switches the power On / Off. Video Input Modules The SE-700 provides four video input channels. There are two SDI inputs (BNC connectors) and two HDMI inputs. Video Output Modules The SE-700 provides three video output channels. There are two SDI outputs (BNC connectors) and one HDMI Output. Audio Input Two channels of XLR Balanced Audio Input. GPI GPI output connection for basic control of other externallyconnected devices Ethernet Port This port allows connection of the SE-700 to a PC for Firmware Update & Control TALLY Output Sends Red, and Green tally signals to each channel. Red indicates On-Air, and Green indicates next camera source. DC IN DC in socket connects the supplied 12V / 19W PSU. The connection can be secured by screwing the outer fastening ring of the DC In plug to the socket. 8

9 Grounding Terminal When connecting this unit to any other component, make sure that it is properly grounded by connecting this terminal to an appropriate point. When connecting, use the socket and be sure to use wire with a cross-sectional area of at least 1.0 mm 2. USB Port Firmware upgrade 9

10 Control Panel Function Keys F1 F3 11 DSK Selection / PGM & PVW Settings 2 User Memory 12 FTB Fade to Black 3 Menu Control 13 Speed Selection 4 Wipe Transition Selection 14 WIPE Transition Effect 5 Wipe-IN Image Border Setting 15 Take - Cut & Auto 6 Live Video Screen Capture 16 MIX Transition Effect 7 Still Frame Store 17 Transition on PVW Only 8 Background Transition Enabler 18 T-Bar 9 PIP Selection / PGM & PVW Settings 19 Program Row 10 Keyer Selection / PGM & PVW Settings 20 Preview Row Function Keys F1- F3 F1: Switch USER 1-6 to be USER 7-12 F2: TBD F3: Normalise Button User Memory 1-6 Buttons User 1-6 allow the user to save and recall customized settings. 10

11 Menu Control Menu Operation Press the menu button to gain access to the menu; use the up/down/left/right buttons to browse through the menu and press enter button to select or menu button to exit Wipe Transition Selection WIPE Transition Selection Each Wipe button consists of black and white colors. The white represents the current Program image and the black represents the WIPE-IN image. There are a total of 32 WIPE presets offered on the SE-700; 12 WIPE preset buttons allow the user to make selection directly on the control panel and the rest of the 20 WIPE effects are selectable on the menu. REV Pressing this button reverses the direction of the WIPE. BDR ON/OFF Turns ON/OFF the border function BDR SOFT Adjustment of the border softness (To fine tune the border softness, please use the Soft option in the menu) BDR COLOR Selection of the border color BDR SIZE Selection of the border thickness GRAB The Grab feature allows the user to grab and save the current Program video image to the Freeze option of Preset and Program rows. FS1 FS3 Still images can be assigned to the frame store buttons and pressing the button selects the corresponding image to the Still Option of Program and Preset rows. 11

12 TRANS BG Enables Program / Preset Background Transition PIP Selection / PGM & PVW Settings PIP SETUP: Press PIP SETUP button to open PIP configuration menu PIP PVW: Enables the PIP on PVW / press and hold to select PIP source PIP PGM: Enables the PIP on PGM Keyer Selection / PGM & PVW Settings Keyer SETUP: Press Keyer SETUP button to open Keyer configuration menu (Chroma / Luma / Linear)/ press and hold the button to select FILL SOURCE Keyer PVW: Enables Keyer on PVW / press and hold the button to select KEY SOURCE Keyer PGM: Enables Keyer on PGM DSK Selection / PGM & PVW Settings DSK SETUP: Press DSK SETUP button to open DSK configuration menu (Luma / Linear)/ press and hold the button to select FILL SOURCE DSK PVW: Enables DSK on PVW / press and hold the button to select KEY SOURCE DSK PGM: Enables DSK on PGM FTB Selection of the Fade to Black transition effect Speed Selection Transition speed selection (1, 2 and 3) 12

13 WIPE Function Selection of the WIPE transition effect TAKE - Cut & Auto Cut: Manual transition Auto: Auto transition according to the speed selected MIX Function Mix transition effect PVW TRANS Transition on PVW only BLK Black Background STILL Select STILL picture (FS1, 2, 3 select the Still Image) FREEZE Select FREEZE picture BKG Background Button (Matte & Bars) 13

14 Menu Options This section covers the Menu options in the order that they appear on the screen. These settings are explained in detail in the sub-sections. Options may vary depending on the firmware version in use. Main Menu will appear on the screen after the MENU button is pressed. Use UP/DOWN/LEFT/RIGHT arrows to browse through the Menu and make your selection by pressing the ENTER button. Please note that long pressing the up/down arrow buttons will allow the user to increment and decrement the parameter value at a fast speed. Main Options Sub-Options Parameters M/E Mix Effect Transition DSK Downstream Key Effect FTB Fade-to-Black Effect Wipe Wipe Effect Presets Wipe Soft Border Softness Width Border Width Luma Border Color Luma Start Border Sat Border Color Saturation Hue Border Color Hue X Horizontal Position Position Y Vertical Position Luma Background Matte Luma Matte Sat Background Matte Saturation Hue Background Matte Hue Linear Luma Type of Keyer Chroma Keyer Select if only one source is enabled for the keyer (Key Self source) Select if two sources are enabled for the keyer (Fill and Key Split sources) Lift Parameter for dark/black areas of the key image Keyer Ctrl image Black Keyer Input1 Input2 Input3 Key Source Input4 Key Source Selections Still Freeze Matte Bars Black Input1 Input2 Fill Source Fill Source Selections Input3 Input4 Still Gain Parameter for light/white areas of the key image Opac Parameter for transparency of the overall foreground key 14

15 P-In-P DSK Chroma P-In-P Src Position Border Crop DSK Keyer Ctrl Key Source Fill Source Freeze Matte Bars Hue K Lift K Gain Black Input1 Input2 Input3 Input4 Still Freeze Matte Bars X Y Size Luma Sat Hue Width Left Right Size Top Bot Linear Luma Self Split Lift Gain Opac Black Input1 Input2 Input3 Input4 Still Freeze Matte Bars Black Input1 Input2 Input3 Input4 Still Freeze Parameter for color of the Chroma key Parameter for the Chroma key in dark or black areas Parameter for the Chroma key in light or white areas P-In-P Source Selections Horizontal PIP Position Vertical PIP Position PIP Size PIP Border Luma PIP Border Color Saturation PIP Border Color Hue PIP Border Width Left Edge of the Crop Right Edge of the Crop Size of the Crop Top Edge of the Crop Bottom Edge of the Crop Type of DSK Keyer Select if only one source is enabled for DSK keyer (Key source) Select if two sources are enabled for DSK keyer (Fill and Key sources) Parameter for dark/black areas of the key image Parameter for light/white areas of the key image Parameter for opacity of the overall foreground key image Keyer Source Selections Keyer Source Selections 15

16 Still User Inputs Load Still Save Still Freeze Load Mem Save Mem Input 1 Input 2 Input 3 Input 4 Crosspoint Matte Bars Memory Location Load Destination Source Pressing this button loads the selected still picture source Still FS1 Still FS2 Still FS3 Input1 Input2 Input3 Input4 Freeze Still FS1 Still FS2 Still FS3 Input1 Input2 Input3 Input4 Freeze Pressing this button saves the selected still picture Save Memory Location 1 Sets the Frame store mode of Input 1 to Still/Freeze/Live 2 Sets the Frame store mode of Input 2 to Still/Freeze/Live 3 Sets the Frame store mode of Input 3 to Still/Freeze/Live 4 Sets the Frame store mode of Input 4 to Still/Freeze/Live Memory Load Memory Save Black White Chrom Black White Chrom Black White Chrom Black White Chrom 1 2 Memory Selections Selection of this button loads the selected memory Memory Selections Selection of this button saves to the selected memory Black Level White Level Chroma Level Black Level White Level Chroma Level Black Level White Level Chroma Level Black Level White Level Chroma Level Input 1 Input 2 Input 3 Input 4 Still Freeze Input 1 Input 2 16

17 Setup Outputs Audio GPI Out Standard Outputs 1/2/3 Input 3 Input 4 Still Freeze Input 1 Input 2 Input 3 Input 4 Still Freeze Input 1 Input 2 Input 3 Input 4 Still Freeze Input 1 Input 2 Input 3 Input 4 Still Freeze Input 1 Input 2 Input 3 Input 4 Still Freeze Freeze Still Input 4 Input 3 Input 2 Input 1 Clean PVW Clean PGM PGM DSK1 PVW Out PGM Out Multiview Audio Enable/Disable SDI 1 Audio Enable/Disable SDI 2 Audio Enable/Disable HDMI Audio Enable/Disable GPI Enable/Disable Level/Pulse Pulse width GPI-out assignment ON/OFF SDI 1 SDI 2 HDMI ON/OFF Mode Width Input 1-4 Delay i/50 Resolution Selections Save Saves the selected resolution 17

18 Start Start option is primarily for the user to configure transition effects, such as mix effect, fade-to-black, and wipe. The sub-options are: Transition Wipe Border Position Matte Start Transition M/E 30 DSK 30 FTB 30 Keyer P-In-P Wipe Wipe 1 Soft 0 Width 10 DSK Border Luma 90 Sat 61 Hue Still Position X 0% Y 0% User Inputs Matte Luma 81 Sat 86 Hue Setup Transition Transition feature allows the user to switch between PVW and PGM views. The user may select the transition effect and customize the selected effect. The configurable transition effects under this sub-option are Mix Effect (M/E), Downstream Key (DSK) and Fade-To-Black (FTB). Wipe This sub-option provides the user with the capability of Wipe Effect selection and configuration of the border softness and width of the selected wipe effect. Wipe Wipe Effect Selection Soft Low value yields a distinguished border and high value yields a diffused border Width Low value yields a thin border and high value yields a thick border Border After selecting this sub-option, the user will then be allowed to fine-tune the border color by adjusting the Luma, Saturation and Hue values, i.e. Luma, Sat and Hue. Position Position allows the user to adjust the centre position of some wipes (e.g Circle & Elipse). X represents the horizontal position and Y represents the vertical position. X Positive value: position the wipe centre to the right Negative value: position the wipe centre to the left Zero value: Position the wipe centre at the screen centre Y Positive value: move the wipe centre up Negative value: move the wipe centre down Zero value: Position the wipe centre at the screen centre Matte The user is allowed to configure the Matte Luma, Saturation and Hue under this sub-option. 18

19 Keyer Keyer of the SE-700 provides the user with the capability of image keying. Start Keyer Linear Self Keyer Keyer Ctrl Lift 0 Gain 1.0 Opac 100 P-In-P Key Source Input 4 DSK Fill Source Black Still User Chroma Hue K Lift 0 K Gain 3.0 Inputs Setup Keyer There are three keying modes available: Linear, Luma, and Chroma. After the keying mode is chosen, select Self if only one source is enabled for the keyer, which is Key source and select Split if two sources are enabled for the keyer, which are Fill and Key sources. Keyer Control Keyer Control adjusts lift, gain and opacity of the key image. Lift adjusts the dark/black areas of the key image. Gain adjusts the light/white areas of the key image. Opacity adjusts the transparency of the overall foreground key image. Key Source This sub-option allows the user to assign the key source; various options are listed below: Black Input1 Input2 Input3 Input4 Still Freeze Matte Bars Fill Source This sub-option allows the user to assign the fill source; various options are listed below: Black Input1 Input2 Input3 Input4 Still Freeze Matte Bars Chroma Hue: This parameter adjusts the color of the Chroma key, for example, red is 355 and blue is 235. Key Lift (K Lift): This parameter adjusts the performance of the Chroma key in dark or black areas. Apply more Key Lift if the dark areas are becoming too transparent. Key Gain (K Gain): This parameter adjusts the performance of the Chroma key in light or white areas. Apply more Key Gain if the light areas are becoming too transparent. 19

20 P-In-P Picture-In-Picture (P-In-P) places an image on the PGM or PVW screens. Start P-in-P Src Black Keyer Position X 20% Y 10% Size 50% P-In-P Border Luma 0 Sat 0 Hue 0.0 DSK Border Width 0 Still Crop Left 0 Right 0 Size 0 User Crop Top 0 Bot 0 Inputs Setup P-In-P Source This sub-option allows the user to assign the P-In-P source; various options are listed below: Black Input1 Input2 Input3 Input 4 Still Freeze Matte Bars Position The user is allowed to adjust the position of the PIP screen by adjusting values of X, Y and SIZE, where X is the horizontal position, Y is the vertical position and Size is the PIP screen size. X Y Size Positive value: position the PIP image to the right Negative value: position the PIP image to the left Zero value: Position the PIP image at the center Positive value: move the PIP image up Negative value: move the PIP image down Zero value: Position the PIP image at the center Ranges from 0 to 100 with 0 being the smallest and 100 being the largest Border PIP border color can be adjusted by adjusting the Luma, Saturation and Hue values. Width of the border can also be adjusted. Crop The PIP image crop can be adjusted by modifying the following parameters: Left Adjusts the position of the left edge of the PIP image Right Adjusts the position of the right edgeof the PIP image Size Adjusts the PIP image crop size Top Adjusts the position of the top edge of the PIP image Bot Adjusts the position of the bottom edge of the PIP image 20

21 Downstream Key This feature places downstream key on the PGM or PVW screens. Start DSK Linear Self Keyer Keyer Ctrl Lift 0 Gain 0.0 Opac 0 P-In-P Key Source Black DSK Fill Source Black Still User Inputs Setup DSK The DSK keyer options are Linear and Luma. After the DSK keyer option is chosen, select Self if only one source is enabled for DSK keyer, which is Key source and select Split if two sources are enabled for DSK keyer, which are Fill and Key sources. Keyer Control Keyer Control adjusts lift, gain and opacity of the key image. Lift adjusts the dark/black areas of the key image. Gain adjusts the light/white areas of the key image. Opacity adjusts the transparency of the overall foreground key image. Key Source This sub-option sets the source of the downstream key source. Black Input1 Input2 Input3 Input4 Still Freeze Matte Bars Fill Source This sub-option sets the source of the downstream key fill. Black Input1 Input2 Input3 Input4 Still Freeze Matte Bars 21

22 Still Still allows the user to load images from the memory, save images to the memory, and save the images captured. Start Load Still Still 4 Load Freeze Keyer P-In-P Save Still Freeze Save Still 4 DSK Still Freeze 1 Live 2 Live 3 Live User 4 Live Inputs Setup Load Still Upon selecting Load Still, the user can then choose the memory location from which the still image is loaded. The following are the destinations to which the still image can be loaded: Freeze Input 4 Input 3 Input 2 Input 1 Still FS3 Still FS2 Still FS1 Select Load to load the still image to the determined destination. Save Still Save Still allows the user to save the still image to a specific memory location. The user should determine the source of the still image first. The available sources are listed below: Freeze Input 4 Input 3 Input 2 Input 1 Still FS3 Still FS2 Still FS1 To complete the save, the user can simply select Save after determining the memory location. Freeze Freeze allows the user to load an image to Inputs 1-4 from one of the three sources listed as follows: Still Freeze Live 22

23 User In this option, the user is allowed to load previously saved settings and save the currently configured settings. Start Load Mem Memory 7 Load Keyer P-In-P Save Mem Memory 7 Save DSK Still User Inputs Setup Load Memory Use the up/down arrow to scroll to the desired memory location and load the saved setting by selecting Load Save Memory Use the up/down arrow to scroll to the desired memory location and save the current setting by selecting Save. Please note that the machine defaults to the setting saved to the memory location 0 which can only be found in the User option of the MENU. 23

24 Inputs This feature allows the user to configure the color of the Inputs 1-4. In addition, the user is also allowed to shuffle the contents between Inputs 1-4, Still and Freeze. Start Input 1 Black 0 White 100 Chrom 1.0 Keyer Input 2 Black 0 White 100 Chrom 1.0 P-In-P Input 3 Black 0 White 100 Chrom 1.0 DSK Input 4 Black 0 White 100 Chrom 1.0 Still User Crosspoint 1 Input 1 2 Input 2 3 Input 3 Inputs 4 Input 4 5 Still 6 Freeze Setup Input 1-4 By selecting the corresponding input (Inputs 1-4), the user will then be allowed to configure the color of the input 1-4 by adjusting its Black Level, White Clip and Chroma Gain parameters. Crosspoint Crosspoint gives the user the ability to shuffle the contents between Inputs 1-4, Still and Freeze. In other words, the user will be able to assign any of the sources of Inputs 1-4, Still and Freeze to the 6 input buttons (1, 2, 3, 4, Still and Freeze) of the Program and Preset rows as desired. 24

25 Setup Setup allows the user to perform basic output configuration such as Outputs, Audio, GPI Out and Resolution. Start Outputs PGM Out PGM Out MultiView Keyer P-In-P Audio Off DSK SDI 1 On SDI 2 On HDMI On Still GPI Out Off Mode Pulse Width 1 User Input 1 Delay 0 Inputs Standard 1080i/50 Save Setup Outputs In general, there are three output ports (SDI 1, SDI 2 and HDMI) available, which can be configured to output one of the following: Freeze Still Input 4 Input 3 Input 2 Input 1 Clean PVW Clean PGM PGM DSK1 PVW Out PGM Out Multiview Audio This sub-option allows the user to turn ON/OFF the audio component of the SDI1-out, SDI2-out and HDMI-out. GPI Out The user is allowed to perform GPI configuration. After turning on the GPI, select the GPI mode, which is either level or pulse. The pulse width can also be configured in the sub-option Width (1-9). GPI out can then be assigned to one of Inputs 1-4 and the delay can be set to between 1 and 99. Standard This option allows the user to choose the appropriate output resolution such as 1080i/50. Once done, simply select Save to confirm the selected output resolution. 25

26 Frequently-Asked Questions This section describes problems that you may encounter while using the SE-700. If you have questions, please refer to related sections and follow all the suggested solutions. If problem still exists, please contact your distributor or the service center. No. Problems Solutions 1. In the Still option, images are sometimes distorted if they are captured from live video fed into Inputs 1-4. It is recommended to use still images in the Still option. 2. Is CUT transition available for DSK function? DSK function does not support CUT transition in the current firmware version. 3. What are the expected behaviors of PIP/LUMA/DSK buttons? 4. Why can t image captured using the Freeze function be found after the SE-700 is restarted? 5. Can PIP/KEYER/DSK be enabled at the same time? p Video output on HDMI-1 cannot be displayed on TLM-700HD. 7. Parameter scroll is only one-direction, i.e. once the end of the list is reached, the user should reverse the direction of the scroll to go back to another end of the list. 8. Is there any indication of PIP/Keyer/DSK enable? 9. The user is prompted of the warning of insufficient volume capacity while updating firmware on WIN8 Operating System. PIP PVW/Keyer PVW/DSK PVW Button ON: Effect displayed on PVW Screen; after configuring parameters of PIP/Keyer/DSK, enable PIP PGM/Keyer PGM/DSK PGM to switch PIP/Keyer/DSK to PGM Screen (or the user can use CUT or T-Bar to perform transition; CUT is not available for DSK though). If only PIP PGM/Keyer PGM/DSK PGM are enabled, then the effect is displayed on both PVW and PGM screens. Image captured using the Freeze function will be lost after power is switched off. However, you can save it as a still image if you want to keep it. Yes, PIP/KEYER/DSK can be enabled at the same time with PIP at the bottom most layer, Keyer in the middle and DSK on the topmost layer. Please use TLM-170H/170P/434H for such application. Some of the parameters allow the user to cycle through the available values, whereas other parameters allow only one direction scroll. There are two indications of PIP/Keyer/DSK enable: 1. There are tally indications for channels set to key and fill sources of PIP/Keyer/DSK. 2. Borders of screens of the multiscreen assigned to PIP/Keyer/DSK will be lit with a color. Also, the PIP/Keyer/DSK button will be lit. In the case of upgrading the keyboard firmware, the user should delete the original firmware file first before copying the new firmware file to the device. 26

27 Specifications Connections Total Video Inputs Total Outputs 2 HDMI( ver1.3a) + 2 SDI 1 HDMI (Ver 1.3a ) + 2 SDI SDI Video Input 2 ( 1080i / 720p ) HDMI Video Input SDI Audio Output (PGM Output) Analog Audio Input Internal Frame Synchronizers PGM Out Multiview Out Output can select any of input source Audio Indicator on Multiview Tally Out GPI Software Updates 2 x HDMI(RGB/YUV) 1080i / 1080p / 720p 2CH 2CH XLR 4 All Inputs HDMI / SDI HDMI (720P -> 720P ; 1080i->1080P) SDI (720P -> 720P ; 1080i->1080i) PROGRAM (w/ DSK) Clean PROGRAM PREVIEW ( w/o DSK) MULTISCREEN Input 1~4 Y ( output 2CH) Y Y (Level / Pulse Trigger selectable) Ethernet Standards HD Format Support SDI Compliance Video Sampling Color Precision Color Space 1080i/50, 1080i/59.94, 1080i/60, 720p/50, 720p/59.94, 720p/60 SMPTE 292M.( SDI output /PGM out) 4:2:2 10 bit 4:2:2 10 bit 4:2:2 YUV 27

28 HDMI Input Resolutions for Computers 1280 x Hz 50Hz (720P) and 1920 x Hz 50Hz (1080p & 1080i) Processing Colorspace Conversion Processing Delay Audio Mixer Hardware based real time < 1 frame Selectable audio follow video master gain control Extras Downstream Keyers 1 Linear/Luma Keyers Chroma Keyers Pattern Generators 3 (M/E Keyer, PIP, DSK) 2 (M/E Keyer & PIP) Color Bar PIP 1 XPT Frame Store Control Panel Compatibility Input Voltage Power Consumption Control Protocol Y Total 24 Stills on Internal Memory. One dedicated still buffer, one dedicated freeze buffer. Also, any input can be used as frame store, 3 still frames stored in local frame buffers for instant access. Use PC via Ethernet; Control panel 12V 23W DVIP Multiview Monitoring Number of Windows Routable Windows Tally Windows Source Labels 2 (PGM, PVW) +6 (Inputs 1-4, Stills & Freeze) +2 Output windows (SDI1, SDI2) Y (Follow XPT) Y Y 28

29 Dimensions & Weight *Weight is approximately 4 KG 29

30 Notes 30

31 Notes 31

32 Service and Support 32