Step 1. 1x NXT Ultrasonic Sensor
|
|
- Carmel Garrett
- 5 years ago
- Views:
Transcription
1 Start with the build completed in Lesson 3 of the TETRIX Getting Started Guide. Step 1 involves removing an element from the model. This element will be reattached later. Parts to be Removed Step 1 1x NXT Ultrasonic Sensor Make sure to unplug the battery before making changes to the electrical system. Disconnect the cord attached to the Ultrasonic Sensor before removing the Ultrasonic Sensor from the model. 145
2 Bevel Gear Step 2 1x Single-Servo Motor Bracket 3x 5/16" SHCS 3x Kep Nut Make sure the screws are placed in the correct holes of the servo mount bracket and the front 288 mm channel. 146
3 Step 3 1x 180 Servo Motor 1x Single-Servo Motor Bracket 4x 3/8" BHCS 4x Kep Nut The first time using the servo motor, make sure to unscrew the servo screw using a Phillips head screwdriver to remove the white disk. The second bracket is screwed into the first to create a housing for the servo motor. Place all four screws in the correct holes of the servo and the servo mounts to align the holes and then screw on the kep nuts and tighten the screws. It can be tricky to get the kep nuts on the screws. Try holding the kep nut still behind the lower servo bracket while turning the screw into the kep nut with the appropriate hex key. Do not overtighten the screws; it might crack the plastic servo housing. 147
4 Bevel Gear Step 4 1x Servo Horn 1x Bevel Gear 4x 1/2" SHCS 4x Kep Nut Make sure the screws are snug. 148
5 Step 5 1x Bevel Gear Assembly 1x Servo Screw Use the servo screw that was removed from the servo motor in Step 3 Use the Phillips head on the 4-in-1 screwdriver to tighten the servo screw. Do not overtighten the servo screw. 149
6 TETRIX Add-On Extensions Bevel Gear Step 6 2x Flat Bracket 6x 5/16" SHCS 6x Kep Nut Make sure to attach the brackets to the correct holes in the 288 mm channel element. 150
7 Step 7 1x 160 mm Channel 1x Delrin Bearing 4x 3/8" BHCS Make sure to attach the bearing to the correct holes in the 160 mm channel element. 151
8 Bevel Gear Step 8 1x 160 mm Channel Assembly 4x 5/16" SHCS 4x Kep Nut Attach the 160 mm channel assembly so that the opening in the channel is facing forward on the robot. Make sure the screws are snug. 152
9 Step 9 1x 32 mm Channel 1x Axle Hub 1x Bevel Gear 4x 1/2" SHCS Make sure the set screw on the axle hub is facing forward so you can adjust it easily. 153
10 Bevel Gear Step 10 1x TETRIX Hard Point Connector 2x 5/16" SHCS 2x Kep Nut Do not overtighten the screws; it might crack the hard point connector element. 154
11 Step 11 1x 3 x 5-Module Angular Beam Make sure to insert the 3 x 5 beam in the right direction. 155
12 Bevel Gear Step 12 2x 3-Module Connector Peg with Friction Make sure to insert the connectors into the correct holes of the 3 x 5 beam. 156
13 Step 13 2x 3-Module Connector Peg with Friction 1x 3 x 5-Module Angular Beam Insert the two connectors into the first 3 x 5 beam and then attach the second 3 x 5 beam to the connectors. 157
14 Bevel Gear Step 14 2x 3-Module Connector Peg with Friction 1x 3 x 5-Module Angular Beam 1x NXT Ultrasonic Sensor Insert the two connectors, then insert the Ultrasonic Sensor over the connectors, and close the LEGO assembly with the last 3 x 5 beam over the four connector ends it attaches to. 158
15 Step 15 1x 100 mm Axle Extend the axle through the axle hub until the top of the axle is just below the top of the channel. Remember to tighten the axle hub set screw on the flat side of the axle. 159
16 Bevel Gear Step 16 2x Bronze Bushing Make sure the bushings do not fall out before or during the next step. For this step and Step 17, hold the robot sideways to keep the bushings from falling out. 160
17 Note: The Ranger Bot Base uses one 35 cm and one 50 cm cord for the sensors. The Ranger Bot with Bevel Gears needs two 50 cm cords for the sensors. Step 17 1x Ultrasonic Sensor Assembly 2x Axle Set Collar Insert the axle of the Ultrasonic Sensor assembly through the first bushing and then put the first axle set collar on. Slide the axle all the way through the 288 mm channel element and put the second axle set collar on the axle. Before tightening the set collars, slide the axle through the bushings so the bevel gear is resting on the Delrin bearing, slide each set collar up against the bronze bushing above it, and then tighten each set screw to lock each axle set collar. If the bevel gears need to be aligned differently, loosen both set screws to lift the Ultrasonic Sensor assembly enough so that the teeth of the gears are not touching. When reattaching the cord to the Ultrasonic Sensor, do not tangle the cord with other cords or robot parts. The cord must be able to move freely when the Ultrasonic Sensor rotates back and forth. 161
18 Bevel Gear Final View 162
19 Wiring Diagram Tighten the screws on the HiTechnic controller after the wires have been inserted. Complete all wiring before attaching the battery. 163
Step 1. 1x Single-Servo Motor Bracket. 1x L Bracket
Extensions TETRIX Getting Started Guide Step 1 1x Single-Servo Motor Bracket 1x L Bracket 3x 5/16" SHCS 3x Kep Nut Tips The 7/64" and 5/64" hex keys will be used in this model. Ensure that the teeth of
More informationChallenges. TETRIX Getting Started Guide STEM Challenge Building Guide. Step 1. Parts Needed. Tips
Note: The Arm and Gripper Extension has been recommended as an initial build to complete the STEM Challenge. The STEM Challenge Sample Program and Programming Guide have been created to work effectively
More informationStep 1. 2x Kep Nut 1x Left Motor Assembly
Start with the build completed in Lesson 3 of the TETRIX Getting Started Guide. Steps 1 to 3 involve removing elements from the model. These elements will be reattached later. Parts to be Removed Step
More informationMaterials: Programming Objectives:
Lessons Lesson 1: Basic Chassis Overview TETRIX Getting Started Guide In this lesson, users will learn how to use the elements of the TETRIX system that will be involved in building the basic chassis of
More informationEndurance Robotics PT-3
Endurance Robotics PT-3 The Endurance Robotics Pan and Tilt PT-3 base is a rugged pan and tilt system based around standard sized hobby servos. Featuring all around rigid 1/4" ABS laser cut construction,
More informationBionic Elephant Trunk. Assembly Instructions
Bionic Elephant Trunk Assembly Instructions Equipment and Supplies Required items from the Bionics Kit and/or Materials Pack: 1. Tail fin (small) assembled 2 see Start Here for tail fin assembly instructions
More informationReplacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly
Replacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly Introduction The Backlight Replacement Kit provides a replacement backlight for the PanelMate
More information2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU
2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU 1 The 3613WDU Analog Temperature / RH Sensor Upgrade Kit is used to upgrade Watchdog 2000 Series Weather
More informationTurret Replacement Instruction Manual
Automatic Multi-Satellite TV Antenna Turret Replacement Instruction Manual for models RPSKLGL, RPSKSML, SK-LG00, SK-SM00, & RP-SWM For help, email help@winegard.com or call -800-788-7 568 Raising the Antenna
More informationMP Maker Pro Mk.1. Quick Start Guide
MP Maker Pro Mk.1 P/N 33013 Quick Start Guide ONLINE SUPPORT Monoprice is pleased to provide free online support. For order related issues, contact the Customer Service department through the Live Chat
More informationWaterVue TV Installation & User Manual
WaterVue TV Installation & User Manual 19 Waterproof TV Dimensions of TV Front screen 486mm x 340mm x 3mm Mounting Plate 467mm x 324mm x 48mm 24 Waterproof TV Dimensions of TV Front screen 576mm x 395mm
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Stand Parts and Cables. Remote Control. Also included
1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out of the box. Hold it by its edges only. If you touch the screen, you can cause the TV panel to crack. Included
More informationTeamWork Installation Guide
C G G 00-0V/ A MAX TX RX +V APARATUS US 0 TeamWork Installation Guide TeamWork TeamWork is a fully customizable collaboration system comprised of an switcher, Show Me cables, a control processor, and a
More informationimac Intel 27" EMC 2546 isight Camera and Microphone Cable Replacement
imac Intel 27" EMC 2546 isight Camera and Microphone Cable Replacement Replace the isight/microphone cable in your Late 2012 27" imac. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com
More informationCable ISOBUS Active Termination
ISOBUS Retrofit Kit Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity ISOBUS Retrofit Kit 4100843 1 Hex Head Bolt
More informationPowerBook G4 Aluminum 12" GHz LCD panel upgrade
PowerBook G4 Aluminum 12" 1-1.5 GHz LCD panel upgrade Upgrade a 1400x1050 LCD panel. Written By: martin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The original LCD 1024x768 resolution
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: LPDA 200 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,
More informationAssembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door
CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system
More informationSRV02-Series. Rotary Pendulum. User Manual
SRV02-Series Rotary Pendulum User Manual Table of Contents 1. Description...3 2. Purchase Options...3 2.1 Modular Options...4 3. System Nomenclature and Components...5 4. System Configuration and Assembly...6
More information8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit. Applicable Upgrade Kit Model Number
Installation Note 8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit Network Analyzer Model Number 8753E 8753ET 8753ES Applicable Upgrade Kit Model Number
More informationGeneral Wiring and Installation Guidelines. Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers
General Wiring and Installation Guidelines Typical Mounting Installations Electrical Connections General Guidelines Common Questions & Answers Congratulations on your purchase of a Dynapar brand encoder.
More informationTeamWork Kits Installation Guide
TX 0 RX COM +5V APARATUS US TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher, system controller, Cable Cubby, and cables
More information3M Locator Plate N
M Locator Plate 44-107N Instructions for the assembly of.100 x.100 preassembled socket connectors 1.0 General The M Locator Plate 44-107N is designed to aid in the assembly of the preassembled socket connector
More informationSatellite Dish Installation Manual (Ver. 2) 1
Satellite Dish Installation Manual Provided by DiscoverNet, Inc. Satellite Dish Installation Manual (Ver. 2) 1 Table of Contents Section 1: Introduction Page 3 Section 2: Recommended Tools and Materials
More informationipad Air 2 Wi-Fi Display Assembly Replacement
ipad Air 2 Wi-Fi Display Assembly Replacement Fix a cracked or faulty screen by replacing the display assembly in an ipad Air 2 Wi-Fi. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1
More informationIn-Ceiling Electric Motorized Front Projection Screen Evanesce Series. User s Guide
In-Ceiling Electric Motorized Front Projection Screen Evanesce Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The
More information3. Electronics and MMU2 unit assembly
Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 34 Step 1 Tools necessary for this chapter Please prepare tools for this chapter: 2.5mm Allen key for M3 screws 2mm Allen key for nut alignment
More informationAssembly instructions
Assembly instructions Model: MXR0024/KIT TV Aerial - 18 Element Kit Contact: Helpline: +44 (0)1553 811000 Email: support@maxview.co.uk Web: www.maxview.co.uk Maxview reserve the right to change specifications
More informationM-8460Se Printer Standard Unit
M-8460Se Printer Standard Unit Parts List Page 1-1 P/N 9001090 Table of Contents M-8460Se Spare Parts List Page Frame Assembly...3 Print Head Assembly...8 Ribbon Assembly... 11 Platen Frame Assembly...14
More information2.4 METER SERIES 1250 ANTENNA SYSTEM
June 1,2009 Revision B Assembly Manual 2.4 METER SERIES 1250 ANTENNA SYSTEM General Dynamics SATCOM Technologies 1500 Prodelin Drive Newton NC 28658 2.4 Meter 2 Piece Az/El Installation Instructions B
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Parts in the box Single monitor Dual monitor M2 M8 M/Flex + (package contents will depend on configuration ordered) Tools required for installation 6.0 mm Hex Key
More informationTracVision 95W LNB Installation
TracVision 95W LNB Installation To enable a TracVision system to receive DIRECTV international programming from the linear satellite located at 95W, a 95W LNB must be installed in a secondary M7SK or M9
More information1.8 METER SERIES 1183 Az/El MOUNT ANTENNA SYSTEM
REVISION G January 11, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1183 Az/El MOUNT ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1183 Az/El MOUNT ANTENNA SYSTEM G
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system must be used
More informationHardware installation
Hardware installation 5. Place and fix the OMT to the interface without tightening the screws. Figure 291: Place and fix the OMT to the interface Note: Take care to place the OMT with the engraved ARROW
More information2100/2200/4100/6200 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors
00/00/400/600 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box
More informationREAD ME FIRST. Touchstone TV Lift
Whisper Lift II PRO 2 READ ME FIRST 1. After completing the unpacking and uncrating of the cabinet, you will find the Owner s Manual, TV, installation hardware, and the wireless remote all together and
More informationThe NXT Big Thing #14
The NXT Big Thing #14 The Sound Of... Robots? By Greg Intermaggio LDLDLDLDLDLLDDLLDLD! (Wookie for hello everyone!) In the last edition of The NXT Big Thing, we completed our gyro controlled robots. This
More informationFlat-Bed Module Recorders
Flat-Bed Module Recorders Model No. 08376-50 08376-55 08376-60 0115-0192 4/28/00 Table of Contents Introduction...3 Power Requirements...3 Chart Paper Installation...3 Pen Installation...5 Grounding...5
More informationLED Backlight for Technics amplifiers
LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to
More informationInstalling iphone 3G Display
Tools used in this guide Phillips #00 Screwdriver (1) Small suction cup (1) Spudger (1) Parts relevant to this guide iphone 3G Display (1) Cracked or faulty display? Replacing the glass is somewhat involved
More informationTips to disassemble your TF300. Will hopefully help you not make a couple of the mistakes I did. Written By: B0NK3R5
Disassembling Asus Transformer Pad TF300 Tips to disassemble your TF300. Will hopefully help you not make a couple of the mistakes I did. Written By: B0NK3R5 ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationHi-Rez Projections Inc. 20 Main St. Ashland, MA MP8 CRT Installation
Hi-Rez Projections Inc. 20 Main St. Ashland, MA 01721 508-881-1613 www.hometheater1.com MP8 CRT Installation Table of Contents Overview...1 Precautions...1 Components...1 CAUTIONS Before Beginning...2
More informationFELIX3.1 assemblymanual
FELIX3.1 assemblymanual Assemblymanualfor: FELIX3.1Single FELIX3.1Dual copyrightinformation Thisdocumentcontainsproprietaryinformationthatisprotectedbycopyright. nopartofthisdocumentmaybephotocopied,reproduced,ortranslatedtoanotherlanguagewithoutthepriorwritenconsentoffelixroboticsbv.
More informationDual extruder upgrade manual addendum to assembly manual
Dual extruder upgrade manual addendum to assembly manual This manual is intended for users that have bought the kit WITH a new printer. For user that already have their printer assembled and working, please
More information2100, 2200, 4100, 6200, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors
00, 00, 400, 600, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box 0 975 Cottonwood
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system must be used
More informationipad Air 2 Wi-Fi Display Assembly Replacement
ipad Air 2 Wi-Fi Display Assembly Replacement Fix a cracked or faulty screen by replacing the display assembly in an ipad Air 2 Wi-Fi. Geschreven door: Evan Noronha ifixit CC BY-NC-SA nl.ifixit.com Pagina
More informationADF Module. Installation Guide. 1.1 Overview
ADF Module Installation Guide 1.1 Overview The installation sheet is divided into three sections. Section 1.2 Description on page 2 describes the areas on the frame and modules dedicated to the mounting
More informationThe Mambo Twist LED Screen System
The Mambo Twist LED Screen System The Mambo Twist LED screen system builds on the successful design formula of the Mambo range The Mambo screen system features: 8mm pixel pitch Indoor/outdoor use Light
More informationReplacing the PanelMate epro PS, PanelMate epro PS Classic, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-15xx Series Backlight Assembly
Introduction Replacing the PanelMate epro PS, PanelMate epro PS Classic, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-15xx Series Assembly Instruction Leaflet IL04802009E Effective September 2008
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: MOD 550 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,
More informationSRV02-Series. Ball & Beam. User Manual
SRV02-Series Ball & Beam User Manual Table of Contents 1. Description...3 1.1 Modular Options...4 2. System Nomenclature and Components...5 3. System Setup and Assembly...6 3.1 Typical Connections for
More informationProduct Manual. Designed and Manufactured in the UK by Optikinetics
Product Manual Contents Product Overview... 1 Getting Started... Mounting the Projector... Inserting the Effect Wheel... Focussing the Image... Cleaning the Focussing Lens... 2 2 3 6 6 Operating the Projector...
More informationUltra-Grip Crimp Connector Hand Tool Kit for Coaxial Cable and Powerpole Connectors
Ultra-Grip Crimp Connector Hand Tool Kit for Coaxial Cable and Powerpole Connectors DXE-UT-KIT-CRIMP DXE-UT-KIT-CRIMP-INS-Revision 2b DX Engineering 2014 1200 Southeast Ave - Tallmadge, OH 44278 USA Phone:
More information1Ver.0.2OldStyle. t r i. v t o. m e. a c
Se r v omo t o rf o r I ndus t r i a lse wi ngma c hi ne SV7 1Ver.0.2OldStyle or hmot c t u l c hana gt n i v a s gy r ne e e r o m ntand e i c i f f e e r Mo SV-71 INSTRUCTION MANUAL Ver. 0.2 Old Style
More informationSlingBoard Instructions
SlingBoard Instructions Page 1 of 13 Thank you for selecting the SlingBoard! Table of Contents WARNINGS!!... 3 SAFETY PRECAUTIONS!!... 3 SET UP... 4 FLAT TIRE REPAIR... 9 PARTS DIAGRAMS...11 SLINGBOARD
More informationipad mini 4 LTE Right Cellular Antenna Replacement
ipad mini 4 LTE Right Cellular Antenna Replacement Replace the right cellular antenna in an ipad mini 4 LTE. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Follow
More informationDREAMOC DIAMOND 4K - ASSEMBLY GUIDE VERSION ORIGINAL ASSEMBLY GUIDE
DREAMOC DIAMOND 4K - ASSEMBLY GUIDE VERSION 1.2 - ORIGINAL ASSEMBLY GUIDE It is important to read this assembly guide before using the Dreamoc Diamond, and to follow advices and instructions on safety,
More informationHQ Electromagnetic Channel Locks
HQ Electromagnetic Channel Locks Table of Contents Overview... 2 Kit Contents... 2 Tools Required... 5 Installation... 5 Using the HQ Electromagnetic Channel Locks... 10 Troubleshooting... 11 Overview
More informationDLMP Installation Instructions
DLMP Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420 [ ] 2 x
More informationiphone 7 Plus LCD Screen and Digitizer Replacement
iphone 7 Plus LCD Screen and Digitizer Replacement Replace just the bare front panel not including the home/touch ID sensor, front-facing camera and sensor cable, or earpiece speaker in an iphone 7 Plus.
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 75 OHM AND 75 OHM HD COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Remote Control. Stand Parts and Cables. Also included
1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out of the box. Hold it by its edges only. If you touch the screen, you can cause the TV panel to crack. Included
More informationUltra-Grip 2 Crimp Connector Hand Tool Kit for Coaxial Cable Connectors, Powerpole Connectors, Insulated and Non-Insulated Crimp Terminals
Ultra-Grip 2 Crimp Connector Hand Tool Kit for Coaxial Cable Connectors, Powerpole Connectors, Insulated and Non-Insulated Crimp Terminals DXE-UT-KIT-CRMP2 DXE-UT-KIT-CRMP-INS-Revision 0a DX Engineering
More information1 Remove SCREWS (2) CELL-EXT Cable Assembly Installation Guide. LYNX Touch/QuickConnect Touch Controls. General Information. Remove the 3GL/3GLC
CELL-EXT Cable Assembly Installation Guide For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/mywebtech General Information The CELL-EXT cable assembly is used to connect
More informationLego Robotics Module Guide
Lego Robotics Module Guide The RCX is a programmable, microcontroller-based brick that can simultaneously operate motors, sensors, an infrared serial communications interface, a display and speaker. Get
More informationMotor Operated Solar Shade with Valance Installation and Care Instructions Complete Video Instructions Available Online at
* Motor Operated Solar Shade with Valance Installation and Care Instructions Complete Video Instructions Available Online at www.keystonefabrics.com Step 1: Identify the parts of your shade (parts shown
More informationimac Intel 27" EMC 2639 Display Replacement
imac Intel 27" EMC 2639 Display Replacement Replace the Display in your imac Intel 27" EMC 2639. Rédigé par: Walter Galan ifixit CC BY-NC-SA fr.ifixit.com Page 1 de 16 INTRODUCTION Removing the display
More informationBacklight Replacement
Installation Instructions Backlight Replacement Catalog Numbers 2711P-RL7C, 2711P-RL7C2, 2711P-RL10C, 2711P-RL10C2, 2711P-RL12C, 2711P-RL12C2, 2711P-RL15C Topic Page About This Publication 1 Important
More informationInstruction for Locking Tuner s Carriage(s) before Shipping
Instruction for Locking Tuner s Carriage(s) before Shipping Step 1. Configure tuner properties and verify connection From ATS block diagram view, double click on the tuner that needs to be locked. The
More informationDL-AR2 Technical Specifications Universal HDMI Adapter Ring Rev
DL-AR2 Technical Specifications Universal HDMI Adapter Ring Rev. 130814 The DL-AR2 Digital Adapter Keychain was developed to support the rising proliferation of mobile devices used in presentation systems.
More informationVibratory Deck Sieves 15 in. (380 mm)
Instruction Sheet P/N 1604433-01 Vibratory Deck Sieves 15 in. (380 mm) Introduction This instruction sheet covers the vibratory deck sieves listed in the following tables. 15-Inch Deck Sieves with 2.5
More informationM8400RV Base Cover Assembly Item # Part Number Part Description Qty
Base Cover Assembly Item # Part Number Part Description Qty 1 PH1741200 Base frame 1 2 PT6680100 Rubber foot 4 3 PA3741000 Frame bracket 1 4 MD4301022 Pan head screw 3 5 PA3742500 Frame bracket 1 6 MD4301022
More informationIMPORTANT! Special Instructions for the TracVision M3DX Conversion System ( )
IMPORTANT! Special Instructions for the TracVision M3DX Conversion System (01-0279-05) You have purchased a special TracVision M3DX conversion system that can be configured for either circular or linear
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual REV
REV. 1.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationT5-RM HD MITS. User Manual. 3-Dmed LEARNING THROUGH SIMULATION
T5-RM HD MITS User Manual 3-Dmed LEARNING THROUGH SIMULATION T5-RM HD Minimally Invasive Training System Thank you for purchasing the T5-RM HD MITS from 3-Dmed Each has been fully tested prior to shipment
More informationELLIPTICAL ANTENNA E0851B11
ELLIPTICAL ANTENNA E0851B11 INSTALLATION GUIDE E0851B11 Installation Manual Step 1: Finding a suitable antenna site A suitable antenna site requires an unobstructed view and a stable antenna mounting surface.
More informationTECHNICAL GUIDE. TOUGH GUN ThruArm G2 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-6L, 120iC, 120iC-10L INSTALLATION MAINTENANCE
TECHNICAL GUIDE TOUGH GUN ThruArm G2 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-6L, 120iC, 120iC-10L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW & PARTS LIST ORDERING INFORMATION
More informationK Service Source. Apple High-Res Monochrome Monitor
K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal
More informationK Service Source. Macintosh Color Display
K Service Source Macintosh Color Display K Service Source Specifications Macintosh Color Display Specifications Characteristics - 1 Characteristics Picture Tube 14-in. diagonal (11.5-in. viewable image)
More information2178-L/S Series Fiber Optic Splice Case with Gasket
2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents
More informationTechnical Information Bulletin
June 4, 2001 #TIB0003 Units Affected: Model Serial Numbers Model Serial Numbers SVT-2PRO T2PDxxxxxxxxx SVTAV AXVDxxxxxxxxx ATLDxxxxxxxxx BJIDMAxxxxxxx SVT-2PROJ T2PJxxxxxxxxx SVTAVJ BAHJxxxxxxxxx ATLJxxxxxxxxx
More informationThe Haply Development Kit
The Haply Development Kit Introduction The Haply development kit is a robust and adaptable open-source hardware development platform for haptic applications. Designed to be accessible to novices and experts
More informationTracVision M9 LNB Replacement Instructions
TracVision M9 LNB Replacement Instructions These instructions explain how to replace an LNB with a new LNB of the same type in a TracVision M9. Installation Steps LNB Replacement Instructions 1. Remove
More informationCable System Installation Guide
Overview Cable System Installation Guide 5/19/2008 Our recommended approach for the installation of your Circle Graphics Cable Systems on the panels in your market is to install the fixed hardware (namely
More informationmonolight Q-400 INSTRUCTIONS INSTRUCTIONS
monolight Q-400 INSTRUCTIONS INSTRUCTIONS Introduction Congratulations on your purchase of the Angler Silver 18 softbox! The Angler Q-400 Monolight can be used for everything from professional wedding
More informationUSER S MANUAL. Save this manual for future reference. For a digital version of this manual, visit
TM USER S MANUAL Save this manual for future reference. For a digital version of this manual, visit www.mylifter.com/installation. 4 5 TABLE OF CONTENTS 4 INSTALLING THE PULLEY SYSTEM FOR LIFTING 100
More informationLet s build the EdCrane Difficulty:
EdBuild Let s build the EdCrane Difficulty: The EdCrane EdBuild by Microbric Education is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. EdBuild the EdCrane The EdCrane
More informationAUDIO ROOF KIT P/N , , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
AUDIO ROOF KIT P/N 2882064, 2882065, 2882066 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationElecraft KXAT2 Automatic Antenna Tuner Installation Instructions
Elecraft KXAT2 Automatic Antenna Tuner Installation Instructions Revision A, May 23, 2016 E740294 Copyright 2016, Elecraft, Inc. All Rights Reserved Introduction The KXAT2 internal automatic antenna tuner
More informationMY-HITE ADJUSTABLE TABLE
MY-HITE ADJUSTABLE TABLE Corner T Leg Base Model Number : FCNAHBT Please Read Instructions Before Use ASSEMBLY INSTRUCTIONS ALL WORKSTYLES WELCOME Thank you for choosing Friant. We appreciate the trust
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Stand Parts and Cables. Remote Control. Also included
MIC TV SEARCH KEYPAD SOURCE VOL VOICE CH RETURN GUIDE EXIT CH.LIST SMART HUB 3D MTS CC P.SIZE MENU INFO 1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out
More informationCONNECTING THE FUTURE 19" LINXS LIGHTWAVE INTEGRATED CROSS-CONNECT SYSTEM USER MANUAL
CONNECTING THE FUTURE 19" LINXS LIGHTWVE INTEGRTED CROSS-CONNECT SYSTEM USER MNUL 109003 Issue Rev 2 19" Lightwave Integrated Cross-Connect System (LINXS) User Manual Document Number 109003 Issue Rev 2
More informationSite Installation Model MP-8433
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationTECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L
TECHNICAL GUIDE TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW
More informationSite Installation Model MP-8424
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Stand Parts and Cables. Remote Control. Also included
MIC TV SEARCH KEYPAD SOURCE VOL VOICE CH RETURN GUIDE EXIT CH.LIST SMART HUB 3D MTS CC P.SIZE MENU INFO 1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out
More information