R&S OSP-B200R/B200S2 Satellite System for R&S OSP User Manual

Transcription

1 R&S OSP-B200R/B200S2 Satellite System for R&S OSP User Manual User Manual

2 The User Manual describes the following R&S OSP-B200R/B200S2 models and accessories: R&S OSP-B200R/B200S2 ( ) R&S OSP-B200R/B200S2 ( ) R&S OSP-B200S2 ( ) R&S OSP-B200S2 ( ) R&S OSP-B200P ( ) R&S OSP-Z200A ( ) R&S OSP-Z200B ( ) R&S OSP-Z201A ( ) R&S OSP-Z201B ( ) R&S OSP-Z201C ( ) R&S OSP-Z202AF ( ) R&S OSP-Z202BF ( ) 2017 Rohde & Schwarz GmbH & Co. KG Muehldorfstr. 15, Munich, Germany Phone: Fax: Internet: Subject to change Data without tolerance limits is not binding. R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG. Trade names are trademarks of the owners. The following abbreviations are used throughout this manual: R&S OSP-B200R/B200S2 is abbreviated as R&S OSP-B200R/B200S _01_01_man_1_en

3 Contents Contents 1 Documentation Overview User Manual Operating Manual of the Switch Unit Help Basic Safety Instructions R&S OSP on the Internet Preface Functional Description Satellite System Description of the R&S OSP-B200R Description of the R&S OSP-B200S Accessories for the R&S OSP-B200 Satellite System Installing R&S OSP-200R in the R&S OSP Switch Unit Installing Modules in the Satellite Unit R&S OSP-B200S Operating the R&S OSP Satellite System R&S OSP Satellite System with Wired Link R&S OSP Satellite System with Fiber-Optic Link Switching on the R&S OSP Satellite System R&S OSP Satellite System Interface Connectors of the R&S OSP-B200R Module Connectors of the R&S OSP-B200S2 Satellite Power Consumption...18 Figures Figure 3-1: Module R&S OSP-B200R... 8 Figure 3-2: Module R&S OSP-B200S2 Front view... 9 Figure 3-3: Module R&S OSP-B200S2 Rear view... 9 Figure 3-4: Installation of the OSP-B200R module Figure 3-5: Connection of the OSP-B151 interface Figure 3-6: Module with Slot B front panel removed Figure 5-1: OSP-B200R Module connectors Figure 5-2: OSP-B200S Rear side connectors User Manual

4

5 Documentation Overview 1 Documentation Overview This section provides an overview of the R&S OSP-B200R/B200S2 user documentation. Unless specified otherwise, you find the documents on the R&S OSP product page at User Manual Contains the description of all functions of the R&S OSP-B200R/B200S2. The user manual supports you during your first experience with the product, from installation and configuration to interfaces. It provides explanations, step-by-step procedures, figures and examples. The user manual is available for download on the Internet. 1.2 Operating Manual of the Switch Unit Contains the description of all instrument modes and functions of the R&S OSP Open Switch and Control Platform (switch unit). It is available for download on the Internet. 1.3 Help The R&S OSP-B200R/B200S2 are operated by the software R&S OSP Panel. The software-embedded help content provides quick, context-sensitive access to information for the application of the modules and switch units. The software is available at Basic Safety Instructions Contains safety instructions, operating conditions and further important information. The printed document is delivered with the switch unit. 1.5 R&S OSP on the Internet The website provides: Key facts, features and options for the family of R&S OSP switch units Rohde & Schwarz contacts for information, quotes, demos and calibration services Technical documentation (operating manual for R&S OSP switch units) Brochures and Data Sheets Application Notes Drivers User Manual

6 Documentation Overview The current firmware version with OSA and release notes The R&S OSP Panel software with release notes Related documents and articles News and information on software updates Service Manual (only for registered users) Brochures and Data Sheets The data sheet contains the technical specifications of the R&S OSP. It also lists the options and their order numbers, and optional accessories. The brochure provides an overview of the instrument and deals with the specific characteristics. See Application Notes Application notes and application cards deal with special applications or background information on particular topics. See Drivers Up-to-date instrument drivers are available for download at Release Notes and Open Source Acknowledgment (OSA) The release notes list new features, improvements and known issues of the current firmware or software version and describe the installation. The open source acknowledgment document provides verbatim license texts of the used open source software. See and Service Manual The service manual of the R&S OSP describes handling failed modules, module replacement and troubleshooting. It also contains spare part lists and mechanical drawings. The service manual is available for Rohde & Schwarz personnel, only. User Manual

7 Preface R&S OSP on the Internet 2 Preface This manual describes the satellite options for the R&S OSP family: R&S OSP-B200R Remote control module for one satellite OSP-B200S stock no / 04 R&S OSP-B200S2 Satellite unit with two standard R&S OSP module slots stock no / 04 Together with the different accessories like cables and power supply. The satellite options R&S OSP-B200R/B200S2 can be operated only in connection with one of the R&S OSP switch units R&S OSP120, R&S OSP130 or R&S OSP150. For all information related to these switch units, refer to the R&S OSP manual. User Manual

8 Functional Description Satellite System 3 Functional Description 3.1 Satellite System The R&S OSP satellite system is the transparent extension of two R&S OSP module slots via a cable connection or fiber-optic link. The advantages of the OSP satellite system are: Switch modules can be operated on-site. For example, high-frequency relays can be installed and controlled at the shortest possible distance. The non-conductive fiber-optic link avoids electromagnetic interference. The fiber-optic cables allow long distance connections. The fiber-optic cables can be easily fed through the shielding of anechoic chambers. 3.2 Description of the R&S OSP-B200R The option R&S OSP-B200R is the remote control (RC) interface module for operating the R&S OSP satellite unit R&S OSP-B200S. The single-slot RC module is designed to be installed in one of the base units R&S OSP120, R&S OSP130 or R&S OSP150. Figure 3-1: Remote control interface module R&S OSP-B200R Two versions of the R&S OSP-B200R module are available: Modell No. Description Characteristics Comment Remote control (RC) Electrical interface interface module for for one satellite unit R&S OSP-B200S2 Fibre-optic and electrical interface User Manual

9 Functional Description Description of the R&S OSP-B200S2 3.3 Description of the R&S OSP-B200S2 The module R&S OSP-B200S2 is the satellite unit for the R&S OSP family. It offers two slots for standard size OSP modules Figure 3-2: Front view of R&S OSP-B200S2 satellite with two modules (OSP-B128 and -B102) Figure 3-3: Rear view of R&S OSP-B200S2 satellite unit with interface connectors Two versions of the R&S OSP-B200S2 satellite unit are available: Modell No. Description Characteristics Comment Electrical interface R&S OSP satellite unit Fibre-optic and electrical interface DC input 28 V User Manual

10 Functional Description Accessories for the R&S OSP-B200 Satellite System 3.4 Accessories for the R&S OSP-B200 Satellite System For connecting the R&S OSP-B200 satellite system, the following series of accessories is available to cover all applications: Modell No. Description Description Comment OSP-Z200A LAN-type link cable between satellite and RC module, with 15-pin Sub-D connector, length 5 m OSP-Z200B LAN-type link cable between satellite and RC module, with 15-pin Sub-D connector, length 5 m OSP-Z201A Fibre-optic cable, both sides SC connector, length 5 m OSP-Z201B Fibre-optic cable, both sides SC connector, length 10 m OSP-Z201C Fibre-optic cable, both sides SC connector, length 20 m OSP-Z202AF Fibre-optic cable, one side SC connector, one side FSMA connector, length 5 m OSP-Z202BF Fibre-optic cable, one side SC connector, one side FSMA connector, length 10 m OSP-B200P Power supply for R&S OSP-B200S2, Var 04 (28 V DC, 3.75 A max.) Used for feed-through via FSMA connector. Always two cables SC- FSMA are required. Used for feedthrough via FSMA connector. Always two SC-FSMA cables are required. Use only with fiber-optic connection User Manual

11 Functional Description Installing R&S OSP-200R in the R&S OSP Switch Unit 3.5 Installing R&S OSP-200R in the R&S OSP Switch Unit The option R&S OSP-B200R is a one-slot module that can be installed in each of the three R&S OSP base switch unit models; i.e. R&S OSP120, R&S OSP130 or R&S OSP150. A maximum of three module busses is available in an R&S OSP base unit. Figure 3-4: R&S OSP-B200R RC interface module installed in base switch unit The R&S OSP-B200R is typically connected to two internal module busses, which are, per default, the module bus A11 and A12. Therefore, only one additional module can be operated in the R&S OSP base unit. When installing the R&S OSP-B200R into the R&S OSP base unit, you must only connect two interface cables to the R&S OSP mainboard. For the overall satellite system, make the following connections: Base unit to integrated RC interface module RC interface module satellite unit Satellite unit to integrated relay module These interface connections are shown in the the table and drawing below. Satellite Channel R&S OSP base unit to R&S OSP-B200R R&S OSP-B200R to R&S OSP-B200S2 R&S OSP-B200S2 to relay module A A11 (X2) /A12 (X4) or A13 (X13) to R&S OSP-B200R / X101 Use either a connection by Sub-D cable or a fiber-optic connection R&S OSP-B200S2 / X101 Default connection is A11 to X101 B A11 (X2) /A12 (X4) or A13 (X13) to R&S OSP-B200R / X100 Use either a connection by Sub-D cable or a fiber-optic connection R&S OSP-B200S2 / X100 Default connection is A12 to X100 User Manual

12 Functional Description Installing R&S OSP-200R in the R&S OSP Switch Unit User Manual

13 Functional Description Installing Modules in the Satellite Unit R&S OSP-B200S2 Figure 3-5: Connections of the interfaces for the R&S OSP B200R/S satellite system 3.6 Installing Modules in the Satellite Unit R&S OSP-B200S2 If the satellite unit is ordered together with R&S OSP modules, the these modules are fitted and tested already in the factory. For installing any module later on, proceed as follows. 1. Remove a blank panel (if available) from the front side of the satellite unit. 2. Find the flat ribbon cable in the open slot of the satellite unit. (In each slot, A and B, one flat ribbon cable is available.) 3. Connect the flat ribbon cable to the R&S OSP module s connector. 4. Carefully insert the module into the slot 5. Fix the module with the six screws. Figure 3-6: Satellite unit with slot B front panel removed User Manual

14 Operating the R&S OSP Satellite System R&S OSP Satellite System with Wired Link 4 Operating the R&S OSP Satellite System After installation of the option R&S OSP-200R in one of the R&S OSP base switch unit models R&S OSP120, R&S OSP130 or R&S OSP150, the connection to the satellite needs to be done either by Sub-D cable or by fiber-optic cable. The R&S OSP-B200R/B200S satellite system only can be used in connection with standard R&S OSP modules fitted in the satellite unit. 4.1 R&S OSP Satellite System with Wired Link For remote operation of the satellite unit across a distance of up to 10 m, use the cable R&S OSP-Z200A or R&S OSP-Z200B, as shown below: OSP-B200S Wired Link (with DC) OSP-B200R Connect the Wired Link connector only to the R&S OSP-B200R remote control interface module. Connecting it to any other connector can harm your equipment. In this configuration, the satellite unit R&S OSP-B200S is powered by the R&S OSP base unit via the cable R&S OSP-Z200A or R&S OSP-Z200B. The base unit can supply two R&S OSP modules, each with a maximum of 0.8 A (at 28 V DC). Before powering up the R&S OSP base unit, first connect the remote control interface module R&S OSP-B200R to the satellite unit R&S OSP-B200S2. User Manual

15 Operating the R&S OSP Satellite System R&S OSP Satellite System with Fiber-Optic Link 4.2 R&S OSP Satellite System with Fiber-Optic Link For remote operation of the satellite unit at a longer distances or inside a shielded room, use the cable R&S OSP-Z201x or R&S OSP-Z202x, as shown below: OSP-B200P AC 100V-200V OSP-B200S FOL OSP-B200R Before powering up the R&S OSP base unit, first connect the remote control interface module R&S OSP-B200R to the satellite unit R&S OSP-B200S2 and switch on the power supply OSP-B200P. Operating the satellite unit R&S OSP-B200S in this configuration always requires the power supply R&S OSP-B200P. 4.3 Switching on the R&S OSP Satellite System When the satellite system is correctly installed and connected, you can switch on the R&S OSP base unit. After booting up, the system status is shown by three LEDs. These LED s are available both in the remote interface module R&S OSP-B200R and in the satellite unit R&S OSP-B200R2. The LEDs show the following status messages: Device Power LED Link/Busy LED Overheat LED Remote interface module R&S OSP- B200R Green when power is ON Continuously yellow when link between remote interface and satellite is established. Flashing yellow during data transfer. -- Satellite unit R&S OSP-B200S2 Green when power is ON Continuously yellow when link between remote interface and satellite is established. Flashing yellow during data transfer. Orange when fan is switched on Red if overheating occurs User Manual

16 Operating the R&S OSP Satellite System Switching on the R&S OSP Satellite System In case of overheating, indicated by the satellite unit, the built-in modules are reset. User Manual

17 R&S OSP Satellite System Interface Connectors of the R&S OSP-B200R Module 5 R&S OSP Satellite System Interface 5.1 Connectors of the R&S OSP-B200R Module The following picture shows the layout of the R&S OSP-B200R interface connectors on the module s interface panel. Figure 5-1: R&S OSP-B200R module connectors Connect the Wired Link connector only to the R&S OSP-B200R remote control interface module. Connecting it to any other connector can harm your equipment. 5.2 Connectors of the R&S OSP-B200S2 Satellite The following picture shows the layout of the R&S OSP-B200S2 interface connectors on the satellite unit s rear panel. Figure 5-2: R&S OSP-B200S2 rear side connectors User Manual

18 R&S OSP Satellite System Interface Power Consumption Pin 1 Pin 3 Pin 2 Pin 4 GND + 28 V Figure 5-3: Pin assignment of the satellite unit s power supply DC input Connect the Wired Link connector only to the R&S OSP-B200R remote control interface module. Connecting it to any other connector can harm your equipment. 5.3 Power Consumption Both the satellite system and the modules fitted within the satellite draw power from the R&S OSP base switch units (i.e. models R&S OSP120, R&S OSP130 or R&S OSP150). However, the additional power consumption required by the satellite system is relatively low: Max. 50 ma at 28 V Max. 250 ma at 3.3 V For the power consumption data of the various modules, refer to the data sheet of the R&S OSP. User Manual