USER MANUAL. B-EYE Light. Please Read Over This Manual Before Operating The Light Fixture

Transcription

1 USER MANUAL BEYE Light Please Read Over This Manual Before Operating The Light Fixture

2 1 PRODUCT SPECIFICATIONS 1.1 PRODUCT SPECIFICATIONS The Big BEYE is a high performance wash light, a breathtaking beam light, and a creator of completely new spectacular visual effects. Its unparalleled versatility makes it an extremely interesting creative tool for all lighting designers. Voltage:AC9~26V 5/6Hz Max Power:45W Led: 19*15w RGBW 4in1 leds Pixel Control Led drive current: 1mA Zoom angle: 4 6 Control mode: DMX512, Auto running, Sound active 21/97Channel DMX Control Modes Pan:54 /Tilt:21 (816Bit Resolution) Dimmer: 1% linear dimmer Display: LCD display screen Strobe: 2Hz Dimension:26x415x465mm Weight:15kg

3 1.2 PRODUCT FEATURES Enter UP DOWN ESC\LEFT RIGHT POWER IN POWER IN SWITH FUSE DMX IN DMX OUT

4 2 INSTALLATION 2.1 MOUNTING The fixture can be mounted in any position. Always ensure that mounting surface can withstand 1 times the weight of the fixture. Always use a safety cable when mounting the fixture in any elevated position. CLAMP UPRIGHT HANGING IMPORTANT SAFETY NOTE!! Always use a safety cable when installing this unit!! Be sure that the safety cable is connected to a solid loadbearing structure.

5 2.2 FUSE REPLACEMENT Remove the safety cap by a screwdriver. Fetch the old fuse from safety cap. SAFTY CAP I nstall a new fuse. I nstall the safety cap. Fuse:3A,25V FUSE. 2.3 SAFETY WARNING IMPORTANT ALWAYS READ THE USER MANUAL BEFORE OPERATION. PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA. This product must be installed by a qualified professional. Always operate the equipment as described in the user manual. A minimum distance of.5m must be maintained between the equipment and combustible surface. The product must always be placed in a well ventilated area. Always make sure that the equipment is installed securely. DO NOT stand close to the equipment and stare directly into the LED light source. Always disconnect the power supply before attempting and maintenance. Always make sure that the supporting structure is solid and can support the combined weight of the products. The earth wire must always be connected to the ground. Do not touch the power cables if your hands are wet. ATTENTION This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual. Avoid shaking or strong impacts to any part of the equipment. Make sure that all parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and secure. If there is any malfunction of the equipment, contact your us immediately. When transferring the product, it is advisable to use the original packaging in which the product left the factory. Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired. The lamp (LED) shall be changed if it has become damaged or thermally deformed.

6 3 DISPLAY PANEL OPERATION 3.1 BASIC ENTER Enter the currently selected menu or confirm the current function value DOWN Scroll 'DOWN' through the menu list or decrease the value of the current function UP Scroll 'UP' through the menu list or increase the value of the Current function LEFT Scroll through the main menu or exit from the current submenu RIGHT Scroll through the main menu from the current submenu UP LEFT ENTER RIGHT DOWN 3.2 MENU MENU Setup Dmx address (1~512) Fixture ID (1~) Run Mode Channel Mode DMX512 Auto Sound 21CH 96CH Return Option Language Reset Default Set English Chinese Pan Invert

7 MENU Option Tilt Invert Display Invert Dimming Mode Slow Fast Return Adj Set Access code ~999 Zoom Adj 128~~+128 Rotation Adj 128~~+128 R Max 128~~+128 G Max 128~~+128 B Max 128~~+128 W Max 128~~+128 Pan Adj 128~~+128 Tilt Adj 128~~+128 Return Test Channel 1. Channel 16 About Return

8 3.3 Setup 1 DMX ADDRESS (ADDRESS) DMX Address (1~512) Allows you to select the DMX Address. 1) Press Ok the current DMX Address appear on the display. 2) Use the UP and DOWN keys to plan the DMX Address. 3) Press Ok to confirm the selection to keep current 2 Fixture ID Fixture (1~) Allows you to select the. 1) Press Ok the current Fixture appear on the display. 2) Use the UP and DOWN keys to plan the Fixture 3) Press Ok to confirm the selection to keep current 3 Run Mode Fixture Run Mode DMX 512 Sound Auto Allows you to select the Run Mode. 1) Press Ok the current settings appear on the display (DMX512, or Auto). 2) Use the UP and DOWN keys to select one of the following settings: DMX512 Sound Auto 3) Press Ok to confirm the selection to keep current settings. 4 Return

9 3.4 Option 1 Language Language 中文 English Allows you to select the Language. 1) Press Ok the current settings appear on the display ( 中文, or English). 2) Use the UP and DOWN keys to select one of the following settings: 中文 English 3) Press Ok to confirm the selection or MENU M to keep current settings. 2 Reset Reset Allows you to select the Reset. 1) Press Ok the current settings appear on the display (, Off). 2) Use the UP and DOWN settings: keys to select one of the following 3) Press Ok to confirm the selection to keep current settings. 3 Default Set Default Set Allows you to select the Default Set. 1) Press Ok the current settings appear on the display (, Off). 2) Use the UP and DOWN settings: keys to select one of the following 3) Press Ok to confirm the selection to keep current settings.

10 4 Pan Invert Pan Invert Allows you to select the Pan Invert 1) Press Ok the current settings appear on the display (, Off). 2) Use the UP and DOWN settings: Off keys to select one of the following 3) Press Ok to confirm the selection to keep current settings. 5 Tilt Invert Tilt Invert 1) Press Ok the current settings appear on the display (, Off). 2) Use the UP and DOWN settings: keys to select one of the following 3) Press Ok to confirm the selection to keep current settings. 6 Display Invert Display Invert 7 Display Invert Dimming Mode Slow Fast 8 Return

11 3.5 Adj Set (Password:3) Zoom Adj 128~~+128 Rotation Adj 128~~+128 R Max 128~~+128 G Max 128~~+128 B Max 128~~+128 W Max 128~~+128 Pan Adj 128~~+128 Tilt Adj 128~~+128 Return Allows you to select the Adj Invert 1) Press Ok the current settings appear on the display 2) Use the UP and DOWN settings: 128~+128 keys to select one of the following 3) Press Ok to confirm the selection to keep current settings. 3.6 Test Allows you to select the. Press Ok the current appear on the display. Channel value Enter into the son interface from this, shows the numerical and percentage channel value for check 3.7 About Test Test Allows you to select the. Press Ok the current appear on the display. Current software version About About 3.8 Return Return Return Allows you to select the. Press Ok the current appear on the display.

12 CHAN NEL Channels Red CHANNEL MODE Red fine Green Green fine Blue Blue fine White White fine Linear CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Zoom Rotation CHAN NEL Channels Red CHANNEL MODE Red fine Green Green fine Blue Blue fine White White fine Linear CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Zoom Rotation Red LED 1 Green LED 1 Blue LED 1 White LED 1 Red LED Green LED Blue LED White LED Red LED 18 Green LED 18 Blue LED 18 White LED 18 Red LED 19 Green LED 19 Blue LED 19

13 NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit Tilt 128 bit ) all the others channels stay at bit. RED GREEN BLUE WHITE LED ON MACRO COLOUR LEE REFERENCE COLOUR VALUE R G B W RED FINE GREEN FINE BLUE FINE WHITE FINE LINEAR CTO LED OFF UP LOW 25 K 32 K 4 K 5 K 56 K 6 K 7 K 8 K UNUSED RANGE te: If CTO channel is active, the WHITE channel is disabled White Dirty White Alice Blue Congo Blue Dark Steel Blue Deep lavender Lilac Tint Daylight Blue Flame Red Bastard Amber Deep Orange Pale Gold Apricot Bright Blue Primary Green Special lavender Pale Lavender Deep Golden Amber Medium Blue Bright Pink Mauve Dark Green Leaf Green Dark Blue Light Blue Steel Blue Med Blu Green Peacock Blue Magenta Dark Pink Middle Rose Light Salmon English Rose Light Rose Orange Deep Amber Straw Light Amber Spring Yellow Dark yellow green Just Blue Sky Blue Lavender Light Lavender Pink Carnation Medium Pink Light Pink Sunrise Red Dark Amber Gold Amber Medium Amber Fire Surprise Peach Straw Tint Medium Yellow Black White 5 K White 37 K White 7 K Magenta Yellow Cyan Blue Green Red Macro color OFF

14 STOP STROBE FOREGROUND STROBE BACKGROUND STROBE MACRO TILT TILT FINE OPEN RANDOM FAST STROBE RANDOM MEDIUM STROBE RANDOM SLOW STROBE OPEN FAST PULSATION (25 flash/sec) 18 SLOW PULSATION (,5 flash/sec) OPEN 13 FAST STROBE (25 flash/sec) 4 3 SLOW STROBE (1 flash/sec) CLOSED Operation with option InvertPan Off (Tilt conventionally represented at 35 bit and option Invert Tilt Off) DIMMER DIMMER FINE FULL LIGHT NO LIGHT UP LOW Operation with option InvertPan On (Tilt conventionally represented at 35 bit and option Invert Tilt Off) PAN PANFINE FUNCTION Operation with option InvertPan On (Tilt conventionally represented at 35 bit and option Invert Tilt Off) Reserved Halogen Lamp Simulation, type 5 (25 W) Linear bit Halogen Lamp Simulation, type 4 (2 W) Linear bit Halogen Lamp Simulation, type 3 (12 W) Linear bit Halogen Lamp Simulation, type 2 (1 W) Linear bit Halogen Lamp Simulation, type 1 (75W) Linear bit Halogen Lamp Simulation OFF(Default) RGBW Gamma curve 3 gam ma = 2. RGBW Gamma curve 2 gam ma = 1.5 RGBW Gamma curve 1 gam ma = 1. Dimmer Curve 4 Dimmer Curve 3 Dimmer Curve 2 Dimmer Curve 1 Pan Tilt rmal Pan Tilt Fast (Default) Function off rearmed The functions are actived passing through the unused range and staying 5 seconds in necessary level. Last selected function still active. Enable setting a new function. Operation with option InvertPan Off (Tilt conventionally represented at 35 bit and option Invert Tilt Off) DIMMER CURVE 1 GAMMA 1 LINEAR DIMMER CURVE 3 GAMMA 2, DIMMER CURVE 2 GAMMA 1,5 DIMMER CURVE 4 S

15 RESET COMPLETE RESET Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels RED LED 1 to GREEN LED 1 to BLUE LED 1 to WHITE LED 1 to LED ON COMPLETE RESET PAN / TILT RESET Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels PAN / TILT RESET ZOOM RESET Effects reset is activated passing throug the unused range and staying 5 seconds in Effects reset levels ZOOM RESET UNUSED RANGE LED OFF ZOOM WIDE BEAM NARROW BEAM ZOOM ROTATION FAST ROTATION STOP 193 SLOW ROTATION STOP 19 SLOW ROTATION 128 FAST ROTATION 127 LINEAR ROTATION ZOOM ROTATION(available on zoom channel from bit to 42 bit) MACRO CCW Rotation, speed from 3 RPH to 1 RPM Stop rotation CW Rotation, speed from 1 RPM to 3 RPH Indexed zone. Lens angle = 6. Indexed zone. Lens angle = Indexed zone. Lens angle = 1.42 Indexed zone. Lens angle =.94 Indexed zone. Lens angle =.47 Indexed zone. Lens angle = ZOOM ROTATION(available on zoom channel at bit only) MACRO Lens offset angle:. degree Lens offset angle: +4. degree Lens offset angle: degree Lens offset angle: degree Lens offset angle: +.6 degree Lens offset angle:. degree