Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting

Size: px
Start display at page:

Download "Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting"

Transcription

1 PRODUCT ADC TOPIC ODETICS TCS-2000 CART MACHINE DATE: May 14, 1999 REVISION HISTORY Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting 1999 Olitzky 1.0 Aug. 22, 1997 LOUTH Last revised edition DESCRIPTION VERSIONS USED Firmware: ME 122 (this is the latest version, from 1990) Operator s Manual: Maintenance Manual: Protocol: REQUIREMENTS CABLE REQUIREMENTS The TCS-2000 requires a 25 pin Male to 9 pin Male conversion cable and a B&B Electronics RS-232 to RS-422 Converter or similar converter for control. The cable must have the following connections: TCS-2000 (25 pin Male) Louth ADC (9 pin Male) 7 (GROUND) 4 & 6 (GROUND) 2 (TX -) 2 (RX -) 17 (RX +) 3 (TX +) 14 (TX -) 7 (RX +) 5 (RX -) 8 (TX -) It is also necessary to connect directly to each VTR in the TCS This could require up to 6 standard db 9 male pin-to-pin to db 9 male serial RS-422 cables. Imagine Communications Corp. 1

2 CONNECTIONS The 25 pin Male end of the custom conversion cable should be connected to the B&B Electronics RS- 232 to RS-422 Converter and this converter connected to the Main port labeled Manipulator Electronics on the rear of the TCS-2000 and the 9 pin end plugged into the selected port of the ADC server. Do not attach to TCS-2000 port labeled Sequence Controller. Be sure that power is supplied to the B&B Electronics RS-232 to RS-422 Converter. Communications may be erratic without this power connection. Make sure all cable connector screws are tightened securely. Each standard RS-422 cable should connect from the 9 pin Remote 1 port of a VTR to the selected port of the ADC server. This provides machine control for the individual VTR. It may also be desirable to connect a dumb terminal or a computer running a terminal emulator (with or without logging capabilities) to the Odetics Service Manipulator Electronics port. This will provide a real time window into the serial communications between the ADC and the TCS-2000 and may be useful in troubleshooting. This is a standard RS-232 connection. DEVICE HARDWARE SETTING No switches or jumpers are required to be set in the TCS COMMUNICATIONS PARAMETERS The communications parameters for the TCS-2000 are: Baud Rate: 9600 Data Bits: 8 Parity: None Stop Bits: 1 DEVICE SERVER SET-UP To configure the TCS-2000 in the system follow these steps: Select the Options pull down menu in the ADC device server. 1. Select Configure Devices and choose the device number to which the TCS-2000 is to be assigned. The device number is the port to which the RS-422 cable is connected on the ADC. 2. Select Change. 3. Select Cart Machine from the list of devices and Odetics TCS2000 for the protocol. Select OK and then Save. The system will prompt for confirmation. 4. Select the Options pull down menu again. 5. Select Device Parameters and choose the device Odetics TCS-2000 to set-up the device for Imagine Communications Corp. 2

3 operation and select OK. 6. Select DEVICE NAME. The default device name is CART. If a different device name is desired Click on Change, enter the new name using the keyboard and click on OK. 7. With the VTRs cabled and powered on, select VTR PORTS from the Device Parameters list and click or TAB to the VTRs found in the TCS The top VTR is VTR1 then VTR2, etc. The last VTR is VTR6. Type the port assignment of each VTR. Note that the VTR ports are assigned from Device Parameters for the TCS-2000 not from the Configure Devices menu. 8. Once again from the Device Parameters, select Audio/Video List for each VTR and list in the system and fill in the appropriate Audio/Video Out and Audio/Video In crosspoints. 9. When satisfied with all parameter selections, select Save and the set-up will be made permanent. To save your settings to disk, select the Options pull down menu and then Save Options. 10. The VTRs of the TCS-2000 must be assigned to a list. Select the Options pull down menu and then select Assign Devices. 11. Click on the desired list then click on Add/Move to assign the VTR to that list. To save the list settings to disk, select the Options menu and then Save List Settings. OPERATION NOTES There are separate service bins for the loading and unloading of tapes in the TCS These Load and Unload Bins are located in column C. The standard and preferred position of the Load Bin is opened (bin slots visible to the user). The standard and preferred position for the Unload Bin is closed (bin slots available internally in the TCS-2000). NOTE: Do not attempt to load tapes via the Unload Bin. These tapes will not be commissioned into the Cart Bin Collection. All tapes are ejected from the TCS-2000 via the Unload Bin. The Unload Bin automatically rotates when all of its slots are full. At this time remove the tapes and press the Unload Rotate button to restore the Unload Bin to the preferred closed position. If it is necessary to unload a partially full Unload Bin, press the Unload Rotate button above the Unload Bin to open the Unload Bin, unload the tapes and press the Unload Rotate button to restore the Unload Bin to the preferred closed position. NOTE: Do not remove tapes from the internal bins of the TCS-2000 by hand. This may cause future Unusable location errors. Tapes should be loaded into the TCS-2000 via the Load Bin. Place tapes in any open slot of the Load Bin. When the required tapes have been loaded, press either button located above the Load Bin to rotate the Load Bin. All tapes in the slots will be barcode read and stored in the internal bins of the TCS When all tapes have been removed from the Load Bin, the Load Bin will automatically rotate back to the opened position. The ADC is able to control the TCS-2000 even when one or more arms are taken off-line. The ADC Imagine Communications Corp. 3

4 normally uses all available arms to effect increased throughput. When a new tape is required in a VTR, and there are at least two arms on-line, the ADC will use the following scheme: 1. Get the new tape in one of the available arms. 2. Retrieve the ejected tape from the VTR with another available arm. 3. Load the VTR with the new tape. 4. Put the retrieved tape back in its bin location. If only one arm is available, the ADC is still able to operate the TCS-2000; however a more limited tape handling scheme will be used: 1. Retrieve the ejected tape from the VTR with the only available arm. 2. Put the retrieved tape back in its bin location. 3. Get the new tape with the only available arm. 4. Load the VTR with the new tape. Whenever the Load or Unload Bins are to be rotated the elevator-arm assembly is positioned to a safe location. The ADC places Arm 4 of the TCS-2000 in position at Tape Transport 4 in Column H, Arm 1 at Column B, Arm 2 at Column D, and Arm 3 at Column F. It also places the barcode reader at Column C which contains the Load and Unload Bins and ensures the arm assembly is not blocking the Load and Unload Bins. In the System pull down menu of the device server, there is a selection Device Diagnostics. From this menu the various devices can be selected and then specialized diagnostic services for the device can be accessed. The TCS-2000 provides the following diagnostic services: Reinitialize Cart Reverify Bins (Not Availble) Elevator Operation VTR External Operation ARM Offline/Online Reinitialize provides full initialization of the cart machine. It will initialize the Elevator, Hub, and Arm mechanism, rotate the Load Bin to the opened position, as well eject any tapes found in the VTRs and replace them into a bin storage or eject them from the cart machine. If the TCS-2000 is running in manual elevator operation, reinitialization will place the elevator and all arms back in service. Any VTRs which have been placed in external mode must be put back in service via the VTR External Operation. They will not be placed back into internal Odetics control automatically by a reinitialize. Reinitialization does not read the bar code ids of the tapes in the TCS-2000 bins. It is necessary to use Reverify Bins to read the tape ids. It is advised that the Unload Bin be rotated to the closed position as soon as possible after reinitialization of the TCS-2000 if it in not in the closed position. Normal position for the Unload Bin is closed, however the ADC will not autoimatically close this bin for operator safety. Reverify Bins (not functioning) provides a non-disruptive verification of the ids found in the bins of the TCS No threaded cassettes are ejected in this process, thus the list may still continue running during verification without placing the VTRs off-line. The existing entries in the cart s media library will not be automatically deleted, but each one checked as the barcode read of the bin is completed. If a mismatch is found between the id thought to be in the media collection and the physical id input from the barcode read the original id will be removed from the media collection and the newly read id inserted as the data for that bin. This will allow resynchronization of the TCS-2000 real tape collection and the ADC Imagine Communications Corp. 4

5 media collection for this device. A reverify bins cannot be started while the elevator is in manual operation. The reverify operation is a background operation. All loading of cassettes into VTRs and removing of tapes from VTRs is of higher precedence and may temporarily stop the verification process. Also during a library reverify there is a temporary suspension of the loading of new cassettes into the TCS-2000 and removal of cassettes from the TCS Elevator Operation allows the user to place the TCS-2000 into manual operation or restore it to automated operation. In the manual mode the elevator, hub and arm mechanisms are placed off-line for maintenance or repair and the operator becomes the replacement for the elevator and arm mechanisms. This mode must be run with the main doors of the cart machine opened since the operator must have ready access to all of the bins as well as the vtrs. Prompting will be given to indicate when tapes need to be loaded into VTRs from the TCS-2000 library or removed from VTRs and replaced into the TCS-2000 tape library. It is necessary to Enable Pop up Diagnostic Window from the Errors menu of the Preferences menu on the client being used. This will allow the prompting messages to appear on only that client. Other clients will not be affected. Each pop up window must be closed before the next diagnostic message is displayed. This insures that no message is missed and that tapes are moved in the order they are needed by the vtrs. In this mode no cassettes should be manually removed from the cart machine cassette bins except when requested to thread into a VTR. No tape should be placed into a different cassette storage bin than its original bin location, or be exchanged with a tape of a different id. No tapes should be added into the cart machine. The ADC will not recognize any new tapes physically placed into the storage bins of the cart machine. Also at this time it is not possible to use the load/unload bins of the TCS VTR External Operation is used in conjunction with the manual mode to remove VTRs from the automatic cart machine threading logic and make them operate like other external VTRs. Ids which are not found in the TCS-2000 library can be loaded into the external VTRs and recognized by the ADC via non-tcs-2000 barcode read, userbits read, or manual events. Any VTR placed into external operation will become a floater and be available to any list running in the ADC. Refer to External VTR operation descriptions in the ADC manual for additional details. Putting one of the cart machine vtrs into external mode can only be done while the elevator is in manual operation. Remember that the main doors of the TCS-2000 must be opened because the operator requires full access to the vtrs and bins. Putting a vtr into external operation allows media which were not loaded into the cart machine at the time it was placed in manual elevator operation to be played. Since the load port does not function during manual elevator operation no additional tapes can be added to the TCS-2000 once it is place in manual elevator mode. Eventually it may be necessary to play spots on tapes not found in the cart bins. The external vtr (in the cart) provide a resource to play these spots. If there are external vtrs which can handle the same tape format as the cart there would be no need to place cart vtrs into external operation. Arm Offline/Online allows one or more of the TCS-2000 arms to be placed out of service for Maintenance or repair and then returned to the pool of arms available for automatic operation. Arms which are placed offline are no longer used to transport cassettes within the cart machine. The TCS will operate in an automated mode with as few as one arm online, however if multiple short events occur back to back there may not be sufficient time to keep the vtrs threaded. It may be advisable to use a longer thread time as arms are removed from automation service. Imagine Communications Corp. 5

6 TEST PROCEDURES The TCS-2000 should be tested with the ADC software to insure all cabling is correct and the TCS-2000 and its VTRs are communicating with the ADC server. Ensure that the serial RS-422 cable is attached to the server and that the appropriate RS-232 converter has been included in the cable connections as described above. Bring up the ADC software. When finished configuring the TCS-2000 on the device server, open the Device Status Window and verify that the device status is something other than NO DEV. If it is NO DEV then the device server and the TCS-2000 are not communicating. A status of NO COM indicates a failure of the ADC serial port being used or a non-existent serial port. Verify that the cable are properly connected, the device is powered on and configured in the device server. If there is still no communications, verify that the signals are being sent and received through the RS-422 cable using a VOM attached to the transmit and receive lines. There should be change in the voltage on these lines. An RS-422 analyzer may also be used in-line to verify communications. The communications with the Manipulator Electronics of the TCS-2000 will be tested by device initialization or Re-Initialization. This will initialize the Elevator, Hub, and Arms and rotate the Load Bin to the opened position. It will also eject any tapes found in the VTRs and replace them into bin storage or eject them. It is advised that the Unload Bin be rotated to the closed position as soon as possible after initialization or reinitialization of the TCS Normal position for the Unload Bin is closed, however the ADC will not autoimatically close this bin for operator safety. Test the eject mechanism for the TCS-2000 bins by ejecting a number of tapes. Open the Cart Machine Bin window and mark tapes to eject. Then under the Devices Menu option select Eject Bins and make sure that the tapes are moved to the Unload Bin. The Unload Bin should rotate to the opened position as soon as the last slot in it is filled with an ejected tape. Empty the tapes and press the Unload Rotate button above the Unload Bin to return the Unload Bin to the closed position. Test the loading of tapes by putting one or more tapes into the Load Bin of the TCS When the tapes have been loaded, press the Load Rotate button or the Load Immediate button. Make sure that the TCS-2000 barcode reads the tapes and moves them to internal bins. If any tape fills the next to last bin of the TCS-2000 the ADC should determine which bin is not needed for List operation and should eject a tape to the Unload Bin. The Unload Bin will automatically rotate to the open position when its last bin is full. One bin should always remain empty in the TCS With tapes in the TCS-2000, build a playlist that contains these tape ids. Load the list into a Transmission list. Make sure KEEP LIST THREADED is enabled under List Type under Transmission Menu options. Use Program Run on the Control Panel to thread the list. Make sure the elevator moves tapes to the VTRs and that they cue correctly. Unthread the list using Unthread on the Control Panel and make sure the tapes are returned to their respective bins. ERROR CONDITIONS AND RECOVERY: Before a VTR is uncabled or powered off, the VTR must be disabled first. 1. Make sure that the VTR is in eject status. 2. De-assign the VTR from the list. 3. Under Device parameters for the TCS-2000, select VTR PORTS. 4. Click or use the space bar to clear the VTR that is to be disabled. 5. Press OK, then SAVE to change the TCS-2000 Parameter. 6. When putting a deck back on line it must be powered on and cabled before it is enabled Imagine Communications Corp. 6

7 in the Server. 7. If this setup is permanent, it can be saved when a saved options is done. Before Device Initialization or Re-Initialization is initiated, be sure that the Service Door of the TCS-2000 is closed and preferably latched. If the door is not closed and the ADC detects a Service Door Open state the initialization sequence WILL NOT COMPLETE. These commands will remain in the internal command queue for the TCS-2000 and execute as soon as the Service Door is closed. This is to ensure the Tape Bins located in columns C, D and E, and the Load and Unload Bins can be correctly serviced and tape ids in these columns read and stored in the Cart s Library. At any time during operation, if the Service Door is opened, commands to move tapes to or from bins located in columns C, D, and E will not be executed and the Load and Unload bins will not be serviced. These commands will remain in the internal command queue for the TCS and execute as soon as the Service Door is closed. It is best not to attempt to run the TCS-2000 with the Service Door opened for any extended period of time. (If the Service door is opened while the ADC is executing a command to access a bin located in the door it is possible that an Unusable Location Error will occur. The TCS-2000 may have failed to fetch a tape from a door location and the Gripper Closed without a tape. Or the TCS-2000 may have failed to insert a tape into door location. In this case the tape may have dropped. Either open the gripper or place the fallen tape in the gripper of the arm at the Service Door and shut the Service Door. The ADC should attempt to retry the operation.) Certain commands given to the TCS-2000 Manipulator Arm can cause Unable to Execute Responses. The ADC should decode these responses and output a descriptive entry into the Error Log if one of these conditions occurs. The following table is provided as a guide to these responses. Response UA UB UC UE UF UG UH UI UJ UL UM UN US UW UX Description or Cause Arm is off-line Bin inaccessible No cart in gripper Elevator is off-line Arm is off-line Can t go on-line Gripper not closed Hub is off-line Invalid parameter Cart jarred Load/Unload bin not fully closed Mechanical interference Buffer not open Slider not home Arm/Wand in the way Arm extended In the event that the TCS-2000 exhibits a mechanical malfunction the ADC will output a line to the Error Log CART MALFUNCTION - Mnnn. The following table is provided as a guide to these Malfunction Codes. CODE MALFUNCTION DESCRIPTION Imagine Communications Corp. 7

8 CODE MALFUNCTION DESCRIPTION 11 Slider didn t leave home within n milliseconds 12 Slider over-extended to limit switch 13 Slider over-extended too many tachs 14 Slider didn t complete extension within n seconds 15 Gripper not open/closed in time 16 Gripper motor rotated past sensor 17 Gripper sensor is in wrong state after rotation 18 Cart contact not made 19 Slider over-retracted to many tachs 20 Slider didn t complete retraction within n seconds 21 Extend or retract operation not completed in n seconds 22 Gripper open or close operation not completed in n seconds 23 Cart can t be pushed into transport within n seconds 24 Hub locating pin can t be pulled 25 Hub stopped before completion (long tach) 26 Pin drop didn t stop hub rotation 27 Hub didn t index to home within n seconds 28 Pin drop didn t stop hub indexing 29 Pin drop didn t stop hub within n seconds 30 Hub locating pin didn t drop properly 31 Cart can t be pushed into bin within n seconds 32 Mechanical hub malfunction during Barcode Read 35 Load/Unload bin assembly didn t complete rotation within n secs 36 Service door opened while arm extended into or toward it 41 Wrong echo from arm-hub to Manipulator after n tries 42 No response from Arm-Hub to Manipulator received within n secs 43 Wrong/indecipherable response from Arm-Hub to Manipulator 49 Elevator LED did not read stripe correctly 50 Elevator did not end movement on correct bin 51 Elevator did not complete movement within n seconds 52 Elevator did not complete indexing sequence within n seconds 53 Elevator reached lower mechanical limit 54 Elevator reached upper mechanical limit 55 Elevator stalled Certain error conditions may occur in the TCS-2000 which require operator intervention to completely correct the problem. Always try to remedy the situation by allowing the ADC to complete the failed operation. If an error is generated during a thread operation on a cart machine VTR, it is nercessary to determine the cause of the error. There may be a problem with the gripper or arm mechanism or the tape may be missing from its storage bin. Open the door of the TCS-2000 and investigate the cause of the error. If the error was caused by gripper malfunction, correct the problem, close the door of the TCS-2000 and allow the ADC to retry the operation. If the error was not caused by a gripper problem and the tape is physically missing from the storage bin it belongs in, then the event must be cut from the list. Any other use of this id should also be cut from the list or the tape loaded into the cart s library via the Load Bin before the tape is to be cued again. Next, the VTR should be switched from Remote, to Local, and back to Remote. When the door of the Imagine Communications Corp. 8

9 TCS-2000 is closed, the ADC s retry mechanism will attempt the failed command again. It may be necessary to re-execute this recovery procedure at this time, but after this the ADC will toss the failed command. The ADC will only retry TCS-2000 commands one time. INTERNAL DOCUMENT # FILE P:\Engineering\Public Documents\Usernote\Current User Notes\Devices\Cart Machine\Odetics\Odetics TCS2000 Imagine Communications Corp. 9

Revision Protocol Date Author Company Description January Paul DOS REMEDIO S. Imagine Communications

Revision Protocol Date Author Company Description January Paul DOS REMEDIO S. Imagine Communications PRODUCT ADC TOPIC ODETICS TCS-90 CART MACHINE DATE: January 25, 2001 REVISION HISTORY Revision Protocol Date Author Company Description 1.1 25 January 2001 Paul DOS REMEDIO S Imagine Communications New

More information

DX-10 tm Digital Interface User s Guide

DX-10 tm Digital Interface User s Guide DX-10 tm Digital Interface User s Guide GPIO Communications Revision B Copyright Component Engineering, All Rights Reserved Table of Contents Foreword... 2 Introduction... 3 What s in the Box... 3 What

More information

RF Solution for LED Display Screen

RF Solution for LED Display Screen RF Solution for LED Display Screen Introduction RF is a kind of wireless telecommunication technology, now standard IEEE802.11B is much popular. Communication speed between server and terminal can reach

More information

This document describes the different ways to allow the automation system to close a gpi contact from the transmission list.

This document describes the different ways to allow the automation system to close a gpi contact from the transmission list. GPI BOARD (RELAY ACTUATOR & ISOLATED D/I CARD) Date: August 03, 2000 This document describes the different ways to allow the automation system to close a gpi contact from the transmission list. CABLE REQUIREMENTS

More information

Configuration Vestas VMP3500

Configuration Vestas VMP3500 Configuration Vestas VMP3500 1. Table of contents 1. Table of contents... 2 2. Introduction... 3 3. Vestas turbines (RCS)... 4 3.1. VMP 3500 controller... 4 3.2. Communication with the CT3230 current loop

More information

NX APPLICATION NOTE Led Guided Assembly Connector Pinning with Continuity

NX APPLICATION NOTE Led Guided Assembly Connector Pinning with Continuity NX APPLICATION NOTE Led Guided Assembly Connector Pinning with Continuity Background Many wire harness connectors are designed to use a push-click-pull method of wire insertion. This method requires the

More information

DXI SAC Software: Configuring a CCTV Switcher. Table of Contents

DXI SAC Software: Configuring a CCTV Switcher. Table of Contents APPLICATION NOTE MicroComm DXI DXI SAC Software: Configuring a CCTV Switcher Table of Contents 1. Intent & Scope... 2 2. Introduction... 2 3. Options and Parameters... 2 3.1 When to switch the CCTV...2

More information

Manual Addendum For Rerun V1.1 software 12/12/2006, RERUN-A = Serial #06A068, RERUN-P = Serial #06A031

Manual Addendum For Rerun V1.1 software 12/12/2006, RERUN-A = Serial #06A068, RERUN-P = Serial #06A031 Manual Addendum For Rerun V1.1 software 12/12/2006, RERUN-A = Serial #06A068, RERUN-P = Serial #06A031 The Rerun product manual was written for V1.0 software. The new release, V1.1, adds a number of new

More information

O P E R A T I O N M A N U A L. RF-Reader. Stand-alone-Reader Leser 2plus with RS-232 interface

O P E R A T I O N M A N U A L. RF-Reader. Stand-alone-Reader Leser 2plus with RS-232 interface O P E R A T I O N M A N U A L Version 01/05 RF-Reader Stand-alone-Reader Leser 2plus with RS-232 interface Important! Read by all means! To maintain the perfect shipping conditions and to ensure safe operation

More information

JAMAR TRAX RD Detector Package Power Requirements Installation Setting Up The Unit

JAMAR TRAX RD Detector Package Power Requirements Installation Setting Up The Unit JAMAR TRAX RD The TRAX RD is an automatic traffic recorder designed and built by JAMAR Technologies, Inc. Since the unit is a Raw Data unit, it records a time stamp of every sensor hit that occurs during

More information

CI-218 / CI-303 / CI430

CI-218 / CI-303 / CI430 CI-218 / CI-303 / CI430 Network Camera User Manual English AREC Inc. All Rights Reserved 2017. l www.arec.com All information contained in this document is Proprietary Table of Contents 1. Overview 1.1

More information

R5 RIC Quickstart R5 RIC. R5 RIC Quickstart. Saab TransponderTech AB. Appendices. Project designation. Document title. Page 1 (25)

R5 RIC Quickstart R5 RIC. R5 RIC Quickstart. Saab TransponderTech AB. Appendices. Project designation. Document title. Page 1 (25) Appendices 1 (25) Project designation R5 RIC Document title CONTENTS 2 (25) 1 References... 4 2 Dimensions... 5 3 Connectors... 6 3.1 Power input... 6 3.2 Video I... 6 3.3 Video Q... 6 3.4 Sync... 6 3.5

More information

High Performance (Gold Plus) Spliceable Tape Feeder Part Number: Part Number: Revision 3 Jun 2008 No.

High Performance (Gold Plus) Spliceable Tape Feeder Part Number: Part Number: Revision 3 Jun 2008 No. 8mm High Performance (Gold Plus) Spliceable Tape Feeder Part Number: 50934707 12mm High Performance (Gold Plus) Spliceable Tape Feeder Part Number: 50934807 Revision 3 Jun 2008 No. 0930D-E010 i Table

More information

RADview-PC/TDM. Network Management System for TDM Applications Megaplex RAD Data Communications Publication No.

RADview-PC/TDM. Network Management System for TDM Applications Megaplex RAD Data Communications Publication No. RADview-PC/TDM Network Management System for TDM Applications Megaplex-2200 1994 2001 RAD Data Communications Publication No. 351-241-12/01 Contents Megaplex-2200 Edit Configuration Operations 1. Connecting

More information

Weschler AMT Software for the Enhanced Version Transformer Advantage

Weschler AMT Software for the Enhanced Version Transformer Advantage Weschler AMT Software for the Enhanced Version Transformer Advantage The Weschler AMT software is used to configure and monitor a Transformer Advantage from a PC. The AMT software also simplifies extraction

More information

BecauseRFL andhubbel haveapolicyofcontinuousproductimprovement,wereservetherighttochangedesignsandspecificationswithoutnotice.

BecauseRFL andhubbel haveapolicyofcontinuousproductimprovement,wereservetherighttochangedesignsandspecificationswithoutnotice. 1. Introduction 1.1 Overview The RFL VS800 CODEC enables high quality video transmission combined with voice and data over E1 (2.048Mbit/s), T1 (1.55Mbit/s) or Ethernet links. This provides an alternative

More information

Table of Contents. Versa TILE & Versa DRIVE D2 Quick Start Manual

Table of Contents. Versa TILE & Versa DRIVE D2 Quick Start Manual Versa TILE & Versa DRIVE D2 Table of Contents 1. Introduction 2 2. Versa TILE Assembly & Cabling 2 3. Computer & Versa DRIVE Connections 2 4. RasterMAPPER 3 5. Buffer Board 4 6. Testing the System 5 7.

More information

Telesto Private Wire Modem Manual

Telesto Private Wire Modem Manual Telesto Private Wire Modem Manual Telesto Private Wire Modem Manual Revision History Filenames are: G:\Company\Manuals &graphics\manuals \ReferenceManual\Components\Telesto_modem\Private Wire\Remote\RevA\CompleteManual\TelestoPwModemCover.lwp

More information

Kramer Electronics, Ltd. USER MANUAL. Model: VS-201YC. 2x1 s-video Switcher

Kramer Electronics, Ltd. USER MANUAL. Model: VS-201YC. 2x1 s-video Switcher Kramer Electronics, Ltd. USER MANUAL Model: VS-201YC 2x1 s-video Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VS-201YC 2x1 s-video Switcher 4 5

More information

Processor time 9 Used memory 9. Lost video frames 11 Storage buffer 11 Received rate 11

Processor time 9 Used memory 9. Lost video frames 11 Storage buffer 11 Received rate 11 Processor time 9 Used memory 9 Lost video frames 11 Storage buffer 11 Received rate 11 2 3 After you ve completed the installation and configuration, run AXIS Installation Verifier from the main menu icon

More information

Quick Operation Guide of LTN7700/7600 Series NVR

Quick Operation Guide of LTN7700/7600 Series NVR Quick Operation Guide of LTN7700/7600 Series NVR UD.6L0202B0042A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable

More information

Wireless Studio. User s Guide Version 5.1x Before using this software, please read this manual thoroughly and retain it for future reference.

Wireless Studio. User s Guide Version 5.1x Before using this software, please read this manual thoroughly and retain it for future reference. 4-743-161-12 (1) Wireless Studio User s Guide Version 5.1x Before using this software, please read this manual thoroughly and retain it for future reference. DWR-R01D/R02D/R02DN/R03D 2018 Sony Corporation

More information

Kramer Electronics, Ltd. USER MANUAL. Model: 900xl. Power Amplifier

Kramer Electronics, Ltd. USER MANUAL. Model: 900xl. Power Amplifier Kramer Electronics, Ltd. USER MANUAL Model: 900xl Power Amplifier Introduction Contents 1 Introduction 1 2 Getting Started 1 2.1 Recycling Kramer Products 1 3 Overview 2 4 Your 900xl Power Amplifier 3

More information

Modbus for SKF IMx and Analyst

Modbus for SKF IMx and Analyst User manual Modbus for SKF IMx and SKF @ptitude Analyst Part No. 32342700-EN Revision A WARNING! - Read this manual before using this product. Failure to follow the instructions and safety precautions

More information

Network Camera Operating Manual

Network Camera Operating Manual Network Camera Operating Manual Model No. WV-NW484S Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Preface About these

More information

VIDEO GRABBER. DisplayPort. User Manual

VIDEO GRABBER. DisplayPort. User Manual VIDEO GRABBER DisplayPort User Manual Version Date Description Author 1.0 2016.03.02 New document MM 1.1 2016.11.02 Revised to match 1.5 device firmware version MM 1.2 2019.11.28 Drawings changes MM 2

More information

RADIO FREQUENCY SYSTEMS

RADIO FREQUENCY SYSTEMS RADIO FREQUENCY SYSTEMS Optimizer RT FAQ s Q. What information is require before running the software? The Serial Number of each ACU MUST be recorded with the Model number of the antenna that it is attached

More information

Date Received: Software Revision: AEC-BOX-50 AMPEX TO SONY SERIAL PROTOCOL CONVERTER INSTRUCTION MANUAL

Date Received: Software Revision: AEC-BOX-50 AMPEX TO SONY SERIAL PROTOCOL CONVERTER INSTRUCTION MANUAL Date Received: Software Revision: AEC-BOX-50 AMPEX TO SONY SERIAL PROTOCOL CONVERTER INSTRUCTION MANUAL ADRIENNE ELECTRONICS CORPORATION Second Edition January 1997 Copyright (C) 1997 by Adrienne Electronics

More information

Auxiliary states devices

Auxiliary states devices 22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary

More information

Amplification Setup Methods for the Maxprep TM Liquid Handler Technical Manual

Amplification Setup Methods for the Maxprep TM Liquid Handler Technical Manual Amplification Setup Methods for the Maxprep TM Liquid Handler Technical Manual Instructions for use of Products AS9100, AS9101, AS9200, AS9201 TM526 Revised 2/19 Table of Contents 1 Description...2 2...3

More information

Teletext Inserter Firmware. User s Manual. Contents

Teletext Inserter Firmware. User s Manual. Contents Teletext Inserter Firmware User s Manual Contents 0 Definition 3 1 Frontpanel 3 1.1 Status Screen.............. 3 1.2 Configuration Menu........... 4 2 Controlling the Teletext Inserter via RS232 4 2.1

More information

Transmitter Interface Program

Transmitter Interface Program Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following

More information

Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters

Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters Written By: Colin Langridge Issue: Draft Date: 03 rd July 2008 1 Date: 29 th July 2008 2 Date: 20 th August 2008 3 Date: 02 nd

More information

Personal Information Page

Personal Information Page Rev. 08.29.07 Personal Information Page Installing Dealer Name Date of Installation Day Month Year Type of System Executive MD500 MD1000.2 MHDTV MD5Slim MSD60 Freedom (not recommended) Serial Number of

More information

Sony P2 Protocol VTR Control Module v1. Module Application Guide

Sony P2 Protocol VTR Control Module v1. Module Application Guide Sony P2 Protocol VTR Control Module Application Guide Description This module provides control of any Video Tape Recorder (VTR) or Digital Video Recorder (DVR) supporting Sony s P2 Edit Controller Protocol

More information

CobraNet Bundle Assignment Procedure Using CobraNet Discovery

CobraNet Bundle Assignment Procedure Using CobraNet Discovery Summary This procedure will allow Q-Sys to integrate with an existing CobraNet system by providing instructions on setting up CobraNet Assignments for the Q-Sys CCN32 CobraNet Card. NOTE: If the CCN32

More information

For warranty service, please contact Microframe at: A technician will gladly assist you.

For warranty service, please contact Microframe at: A technician will gladly assist you. Your Microframe System is warranted against failure due to defects in workmanship or material for a period of one (1) year from the date of purchase. Microframe Corporation will repair or replace any defective

More information

Remote Application Update for the RCM33xx

Remote Application Update for the RCM33xx Remote Application Update for the RCM33xx AN418 The common method of remotely updating an embedded application is to write directly to parallel flash. This is a potentially dangerous operation because

More information

BY-HPE11KTA. Operating Instructions. Coaxial - LAN Converter with PoE function. Indoor Use Only. Model No. Attached Installation Guide

BY-HPE11KTA. Operating Instructions. Coaxial - LAN Converter with PoE function. Indoor Use Only. Model No. Attached Installation Guide Operating Instructions Coaxial - LAN Converter with PoE function Model No. Indoor Use Only BY-HPE11KTA Attached Installation Guide Before attempting to connect or operate this product, please read these

More information

Video Extender DS128 DSRXL. Instruction Manual. 8-Port Cat5 VGA Digital Signage Broadcaster with RS232 and Audio

Video Extender DS128 DSRXL. Instruction Manual. 8-Port Cat5 VGA Digital Signage Broadcaster with RS232 and Audio DS128 DSRXL Instruction Manual Video Extender 8-Port Cat5 VGA Digital Signage Broadcaster with RS232 and Audio Cat5 VGA Digital Signage Receiver with RS232 and Audio FCC Compliance Statement This equipment

More information

COPYRIGHT NOVEMBER-1998

COPYRIGHT NOVEMBER-1998 Application Notes: Interfacing AG-132 GPS with G-858 Magnetometer 25430-AM Rev.A Operation Manual COPYRIGHT NOVEMBER-1998 GEOMETRICS, INC. 2190 Fortune Drive, San Jose, Ca 95131 USA Phone: (408) 954-0522

More information

J.M. Stewart Corporation 2201 Cantu Ct., Suite 218 Sarasota, FL Stewartsigns.com

J.M. Stewart Corporation 2201 Cantu Ct., Suite 218 Sarasota, FL Stewartsigns.com DataMax INDOOR LED MESSAGE CENTER OWNER S MANUAL QUICK START J.M. Stewart Corporation 2201 Cantu Ct., Suite 218 Sarasota, FL 34232 800-237-3928 Stewartsigns.com J.M. Stewart Corporation Indoor LED Message

More information

Noise Detector ND-1 Operating Manual

Noise Detector ND-1 Operating Manual Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation

More information

Model 6010 Four Channel 20-Bit Audio ADC Data Pack

Model 6010 Four Channel 20-Bit Audio ADC Data Pack Model 6010 Four Channel 20-Bit Audio ADC Data Pack Revision 3.1 SW v1.0.0 This data pack provides detailed installation, configuration and operation information for the Model 6010 Four Channel 20-bit Audio

More information

The Diverse Multimedia & Surveillance System Via Dico2000 with PC DICO Operation Manual

The Diverse Multimedia & Surveillance System Via Dico2000 with PC DICO Operation Manual DICO 2000 Operation Manual Main Screen Overview IP Address & Communication Status Disk Status Screen Mode Warning Status Video Recording Status RUN Setup Search Exit SETUP The beginning ID and Password

More information

Harmony Smart Control. User Guide

Harmony Smart Control. User Guide Harmony Smart Control User Guide Harmony Smart Control User Guide Table of Contents About this Manual... 6 Terms used in this manual:... 6 At a Glance... 6 Features... 6 Supported devices... 6 Know your

More information

DiD. LCD Video Monitor & Video Wall Universal User Manual. Digital Information Display

DiD. LCD Video Monitor & Video Wall Universal User Manual. Digital Information Display LCD Video Monitor & Video Wall Universal User Manual DiD Digital Information Display Video Monitor Models M82S1/M70S1/M65S1/M55S1/M46S1/M40S1/M32S1/M24S1/M19S2/M19S1 Video Wall Models PD55N3/PD46N4/PD46N3/PD46N2/PD40N2

More information

User s Manual. Network Board. Model No. WJ-HDB502

User s Manual. Network Board. Model No. WJ-HDB502 Network Board User s Manual Model No. WJ-HDB502 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. CONTENTS Introduction...

More information

N+1 Redundancy with the VCom HD4040 Upconverter

N+1 Redundancy with the VCom HD4040 Upconverter N+1 Redundancy with the VCom HD4040 Upconverter Document ID: 47164 Contents Introduction Prerequisites Requirements Components Used Conventions Set Up Communication with the Upconverter VCom Dual4040D

More information

ivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1.

ivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1. MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Rev. 1.01 Page i Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice

More information

EEG A1452 SCTE-104 Inserter Frame Card

EEG A1452 SCTE-104 Inserter Frame Card EEG A1452 SCTE-104 Inserter Frame Card Product Manual EEG Enterprises, Inc. 586 Main Street Farmingdale, New York 11735 TEL: (516) 293-7472 FAX: (516) 293-7417 Copyright EEG Enterprises, Inc. 2017 All

More information

ES-450J2 Universal 2 Channel Jog/Shuttle Remote

ES-450J2 Universal 2 Channel Jog/Shuttle Remote ES-450J2 Universal 2 Channel Jog/Shuttle Remote Users Manual ES-450, ES-450J and ES-450J2 are trademarks of JLCooper Electronics. All other brand names are the property of their respective owners. ES-450J2

More information

Design and Use of a DTV Monitoring System consisting of DVQ(M), DVMD/DVRM and DVRG

Design and Use of a DTV Monitoring System consisting of DVQ(M), DVMD/DVRM and DVRG Design and Use of a DTV Monitoring System consisting of DVQ(M), DVMD/DVRM and DVRG When monitoring transmission systems it is often necessary to control the monitoring equipment and to check the measurement

More information

Cisco Spectrum Expert Software Overview

Cisco Spectrum Expert Software Overview CHAPTER 5 If your computer has an 802.11 interface, it should be enabled in order to detect Wi-Fi devices. If you are connected to an AP or ad-hoc network through the 802.11 interface, you will occasionally

More information

OSD. EXECUTIVE / MiniDome USERS MANUAL. USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD

OSD. EXECUTIVE / MiniDome USERS MANUAL. USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD EXECUTIVE / MiniDome OSD USERS MANUAL USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD MotoSAT Corporation Created April 22, 2003 1-800-247-7486 CONGRATULATIONS! on your purchase of your

More information

Mortara X-Scribe Tango+ Interface Notes

Mortara X-Scribe Tango+ Interface Notes Mortara X-Scribe Tango+ Interface Notes To setup Tango+ with the X-Scribe stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate

More information

SERCOS TSX CSY 84 Module V

SERCOS TSX CSY 84 Module V SERCOS TSX CSY 84 Module V At a Glance Aim of this Part What's in this part? This part presents the SERCOS TSX CSY 84 module, its operating features and its installation. This Part contains the following

More information

AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter

AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Broadcast Devices, Inc. AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web:

More information

Quick-Start for READ30

Quick-Start for READ30 Quick-Start for READ30 The program READ30 was written for the purpose of reading and configuring the digital pressure-transmitter of the series 30. The two features are divided into the following parts:

More information

Kaleidescape Co-Star for Lumagen

Kaleidescape Co-Star for Lumagen Kaleidescape Co-Star for Lumagen Installation Guide The Co-Star solution allows a Strato movie player to present a unified onscreen library that includes all of a Kaleidescape customer s movies from DVD

More information

Welch Allyn CardioPerfect Workstation Tango+ Interface Notes

Welch Allyn CardioPerfect Workstation Tango+ Interface Notes Welch Allyn CardioPerfect Workstation Tango+ Interface Notes To setup Tango+ with the CardioPerfect stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232

More information

AES-404 Digital Audio Switcher/DA/Digital to Analog Converter

AES-404 Digital Audio Switcher/DA/Digital to Analog Converter Broadcast Devices, Inc. AES-404 Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web: www.broadcast-devices.com

More information

Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display.

Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display. Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display. Your Stack ST8961 VS module allows you to synchronize, overlay, and record data available on your Stack

More information

TASKI Service Tool Edition: V5.10/2014

TASKI Service Tool Edition: V5.10/2014 Edition: V5.10/2014 Index 1 General 1.1 General information 1 1.1.1 Part reference 1 1.1.2 Consumable supplies 1 1.1.3 Direction description 1 1.1.4 Power source 1 1.2 Required material 2 1.2.1 Tools 2

More information

Commissioning Guide. firepickdelta. Commissioning Guide. Written By: Neil Jansen firepickdelta.dozuki.com Page 1 of 22

Commissioning Guide. firepickdelta. Commissioning Guide. Written By: Neil Jansen firepickdelta.dozuki.com Page 1 of 22 firepickdelta Commissioning Guide Written By: Neil Jansen 2017 firepickdelta.dozuki.com Page 1 of 22 Step 1 Pre-Requisites Before commissioning, please make sure ALL of the following steps have been completed,

More information

Users Manual. altus VTR/DDR Controller HT201, HT211, HT212. Software version: 3.0

Users Manual. altus VTR/DDR Controller HT201, HT211, HT212. Software version: 3.0 altus VTR/DDR Controller HT201, HT211, HT212 Users Manual Software version: 3.0 History Date Description Version Feb 2016 altus manual Version 2.0 2.0 June 2007 altus manual Version 1.0 1.0 June 2010 altus

More information

Guide For Setting Up Your Fortec Lifetime Ultra Receiver

Guide For Setting Up Your Fortec Lifetime Ultra Receiver Guide For Setting Up Your Fortec Lifetime Ultra Receiver Setting up your receiver can be tricky. This document will assist in the process of getting you up and running with minimal effort. Back of the

More information

WV-NP1004. Network Operating Instructions. Network camera. Model No. (Lens is option.)

WV-NP1004. Network Operating Instructions. Network camera. Model No. (Lens is option.) Network camera Network Operating Instructions Model No. WV-NP1004 PUSH TO LOCK/EJECT WV-NP1004 (Lens is option.) Before attempting to connect or operate this product, please read these instructions carefully

More information

invr User s Guide Rev 1.4 (Aug. 2004)

invr User s Guide Rev 1.4 (Aug. 2004) Contents Contents... 2 1. Program Installation... 4 2. Overview... 4 3. Top Level Menu... 4 3.1 Display Window... 9 3.1.1 Channel Status Indicator Area... 9 3.1.2. Quick Control Menu... 10 4. Detailed

More information

HomeVision-PC Owner s Manual Version 2.62

HomeVision-PC Owner s Manual Version 2.62 HomeVision-PC Owner s Manual Version 2.62 Custom Solutions, Inc. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without

More information

Procedure: Procedures: DIME TEAM: Drop # (circle one) Date: In Lab (either on Level 4, Level 6, or in shop): Installation: Functional Check

Procedure: Procedures: DIME TEAM: Drop # (circle one) Date: In Lab (either on Level 4, Level 6, or in shop): Installation: Functional Check Procedure: Red Experiment specific Black - General In Lab (either on Level 4, Level 6, or in shop): Installation: 1. Wear safety goggles when working with the experiment. 2. Perform experiment-specific

More information

User Instruction Manual IQSDA30/IQSDA32. Intelligent Reclocking High Performance HD-SDI/SD-SDI Distribution Amplifiers. snellgroup.

User Instruction Manual IQSDA30/IQSDA32. Intelligent Reclocking High Performance HD-SDI/SD-SDI Distribution Amplifiers. snellgroup. User Instruction Manual IQSDA30/IQSDA32 Intelligent Reclocking High Performance HD-SDI/SD-SDI Distribution Amplifiers snellgroup.com IQSDA30/IQSDA32 www.snellgroup.com Information and Notices Information

More information

Model#: IN-MDRI3MF. Hardware User Manual. 3MP Indoor Mini Dome with Basic WDR, Fixed lens. (PoE) Ver. 2013/02/04

Model#: IN-MDRI3MF. Hardware User Manual. 3MP Indoor Mini Dome with Basic WDR, Fixed lens. (PoE) Ver. 2013/02/04 Model#: IN-MDRI3MF 3MP Indoor Mini Dome with Basic WDR, Fixed lens Hardware User Manual (PoE) Ver. 2013/02/04 Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents... 4 Features and Benefits...

More information

Troubleshooting Guide for E-Poll Book

Troubleshooting Guide for E-Poll Book Troubleshooting Guide for E-Poll Book CHANGING USERS ON THE E-POLL BOOK Changing Users on the E-poll Book 1. Tap Return to Main button on the voter search screen. 2. Tap on the Manage Polls tab in the

More information

4125 system setup and deployment quick start guide

4125 system setup and deployment quick start guide 4125 system setup and deployment quick start guide OPERATION IN AIR Do not operate the system while the tow fish in air for extended periods. The system may be enabled to transmit while in air for test

More information

Kramer Electronics, Ltd. USER MANUAL. Model: FC Analog Video to SDI Converter

Kramer Electronics, Ltd. USER MANUAL. Model: FC Analog Video to SDI Converter Kramer Electronics, Ltd. USER MANUAL Model: FC-7501 Analog Video to SDI Converter Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Your Analog Video to SDI Converter 3 5 Using Your

More information

Fiber Optic Extender User Manual. Model: CV-F01-TX

Fiber Optic Extender User Manual. Model: CV-F01-TX Fiber Optic Extender User Manual Model: CV-F01-TX 1. I/O Connectors Figure 1 CV-F01-TX Fiber Optic Transmitter I/O Connectors 2. Connection introduction Figure 2 CV-F01-TX Fiber Optic Transmitter Connection

More information

Any feature not specifically noted as supported is not supported.

Any feature not specifically noted as supported is not supported. Manufacturer: ELAN Integration Note Model Number(s): EL-4KM-VW44 (Device Ver 2.20; Web Module Ver 6.23) Minimum Core Module Version: Document Revision Date: 8.1.395 5/11/2017 OVERVIEW AND SUPPORTED FEATURES

More information

Kramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher

Kramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in

More information

INSTRUCTION MANUAL. 19 HD Widescreen Water Resistant Television VSPA19LCD-AE1B VSPA19LCD-AE1M VSPA19LCD-AE1W. Model No. FINGER TOUCH TECHNOLOGY RATED

INSTRUCTION MANUAL. 19 HD Widescreen Water Resistant Television VSPA19LCD-AE1B VSPA19LCD-AE1M VSPA19LCD-AE1W. Model No. FINGER TOUCH TECHNOLOGY RATED INSTRUCTION MANUAL 19 HD Widescreen Water Resistant Television VSPA19LCD-AE1B Model No. VSPA19LCD-AE1M VSPA19LCD-AE1W FINGER TOUCH TECHNOLOGY IMPORTANT: Please read these instructions before installing

More information

Gazer VI700A-SYNC/IN and VI700W- SYNC/IN INSTALLATION MANUAL

Gazer VI700A-SYNC/IN and VI700W- SYNC/IN INSTALLATION MANUAL Gazer VI700A-SYNC/IN and VI700W- SYNC/IN INSTALLATION MANUAL Contents List of compatible cars... 3 Package contents... 4 Special information... 6 Car interior disassembly and connection guide for Ford

More information

5620 SAM SERVICE AWARE MANAGER MPTGS Driver Version Guide

5620 SAM SERVICE AWARE MANAGER MPTGS Driver Version Guide 5620 SAM SERVICE AWARE MANAGER 9500 MPTGS Driver Version 2.1.0 Guide 3HE-10851-AAAB-TQZZA September 2016 5620 SAM Legal notice Nokia is a registered trademark of Nokia Corporation. Other products and company

More information

Reference WIRING THE SYSTEM TOGETHER. Page 4-1 TWO OR MORE RECEIVERS

Reference WIRING THE SYSTEM TOGETHER. Page 4-1 TWO OR MORE RECEIVERS 4 Reference WIRING THE SYSTEM TOGETHER TWO OR MORE RECEIVERS Each output on the LNBF can support a single receiver. You cannot connect two receivers to the same output (for example, by using a line splitter),

More information

D/ESAM-230 AUDIO MIXER WITH THE D/ESAM-4 PROTOCOL

D/ESAM-230 AUDIO MIXER WITH THE D/ESAM-4 PROTOCOL TECH NOTE Super Edit Version 8.1D and later D/ESAM-230 AUDIO MIXER WITH THE D/ESAM-4 PROTOCOL This document covers Super Edit features and parameters pertaining to the D/ESAM 4 protocol developed by Graham-Patten

More information

Peak Atlas IT. RJ45 Network Cable Analyser Model UTP05. Designed and manufactured with pride in the UK. User Guide

Peak Atlas IT. RJ45 Network Cable Analyser Model UTP05. Designed and manufactured with pride in the UK. User Guide GB05-7 Peak Atlas IT RJ45 Network Cable Analyser Model UTP05 Designed and manufactured with pride in the UK User Guide Peak Electronic Design Limited 2001/2013 In the interests of development, information

More information

V1602 / V1602CP. ANALOGUE VIDEO ROUTER - 16x2. Rev. 6

V1602 / V1602CP. ANALOGUE VIDEO ROUTER - 16x2. Rev. 6 V1602 / V1602CP ANALOGUE VIDEO ROUTER - 16x2 Rev. 6 June 10, 2004 Network Electronics ASA Thorøya P.O. Box 1020 Sandefjord, Norway Phone: +47 33 48 99 99 Fax: +47 33 48 99 98 e-mail: support@network-electronics.com

More information

Model VS-2A 2-Port VGA Switch with Audio & Serial Control

Model VS-2A 2-Port VGA Switch with Audio & Serial Control Model VS-2A 2-Port VGA Switch with Audio & Serial Control UMA1119 Rev B Copyright Hall Research, Inc. All rights reserved. 1163 Warner Ave Tustin, CA 92780, Ph: (714)641-6607, Fax -6698 Model VS-2A 2 2-Port

More information

ArcPro Mach4 Plasma Screen User Guide

ArcPro Mach4 Plasma Screen User Guide ArcPro Mach4 Plasma Screen User Guide Document Revision 1.10 (Updated June 13, 2017) 2017 Vital Systems Inc. Phoenix, AZ USA For more information please visit the product web page: http://www.vitalsystem.com/arcpro

More information

Chapter 2: Scanner Operations NOTE: Install the software cartridge Power the Scanner Select the software title Identify the vehicle

Chapter 2: Scanner Operations NOTE: Install the software cartridge Power the Scanner Select the software title Identify the vehicle Chapter 2: Scanner Operations This chapter explains general Scanner operations and offers instructions for customizing certain Scanner functions. The following is an outline of basic Scanner operation.

More information

VNS2200 Amplifier & Controller Installation Guide

VNS2200 Amplifier & Controller Installation Guide VNS2200 Amplifier & Controller Installation Guide VNS2200 Amplifier & Controller Installation 1. Determine the installation location for the VNS2200 device. Consider the following when determining the

More information

Model No. ST200-S. Universal VTR/DDR. Controller USER MANUAL 1 ST200-S. Manual Version Document No... ST200-S_User_Manual

Model No. ST200-S. Universal VTR/DDR. Controller USER MANUAL 1 ST200-S. Manual Version Document No... ST200-S_User_Manual 12843 Foothill Blvd. Suite C Sylmar, California 91342 V: 818.898.3380 F: 818.898.3360 sales@dnfcontrols.com Model No. ST200-S Universal VTR/DDR Controller USER MANUAL Manual Version.... 3.11 102506 Document

More information

Model 1476-C SuperQuad HR

Model 1476-C SuperQuad HR Model 1476-C SuperQuad HR Installation and Operating Instructions Table of Contents Page Table of Content... 2 System Description... 3 Features... 3 Installation... 4 Internal Setups... 4 Connections...

More information

GWL/ Power Group Technology Solutions Stay Powered for the Future

GWL/ Power Group Technology Solutions Stay Powered for the Future GWL/ Power Group Technology Solutions Stay Powered for the Future BMS2405 CONNECTION GUIDE: This is simple step-by-step manual how to CONNECT AND proceed basic SETUP of BMS2405. In following example connection

More information

Model 5250 Five Channel Digital to Analog Video Converter Data Pack

Model 5250 Five Channel Digital to Analog Video Converter Data Pack Model 5250 Five Channel Digital to Analog Video Converter Data Pack E NSEMBLE D E S I G N S Revision 3.1 SW v2.0.1 This data pack provides detailed installation, configuration and operation information

More information

Z-D-IN. RS485 Modbus Module 5 Digital Inputs

Z-D-IN. RS485 Modbus Module 5 Digital Inputs S SENECA Z-PC Line EN Installation Manual Contents: - General Specifications - Technical Specifications - Installation Rules - Electrical connections - Modbus connection rules - DIP-switches Settings -

More information

Extra long-range RFID (proximity) card reader

Extra long-range RFID (proximity) card reader GP90A Extra long-range RFID (proximity) card reader (1) Features: Extra long reading range of up to 90 cm with ISO-size passive RFID cards*, over 100 cm with special optimized passive cards High-precision

More information

IRIG-B PTP Clock Converter Output Module Hardware Installation Manual

IRIG-B PTP Clock Converter Output Module Hardware Installation Manual IRIG-B PTP Clock Converter Output Module Hardware Installation Manual Kyland Technology Co., LTD. Publication Date: May 2012 Version: V1.2 Customer Service Hotline: (+8610) 88796676 FAX: (+8610) 88796678

More information

Autotask Integration Guide

Autotask Integration Guide Autotask Integration Guide Updated May 2015 - i - Welcome to Autotask Why integrate Autotask with efolder? Autotask is all-in-one web-based Professional Services Automation (PSA) software designed to help

More information

Stevens SatComm FAQs For use with SatCommSet or Terminal Setup programs

Stevens SatComm FAQs For use with SatCommSet or Terminal Setup programs Stevens SatComm FAQs For use with SatCommSet or Terminal Setup programs Q. What are the channel assignments for On Air Test Mode? A. The assigned GOES test channels are as follows: GOES West 300 Baud:

More information

SECTION 686 VIDEO DECODER DESCRIPTION

SECTION 686 VIDEO DECODER DESCRIPTION 686 SECTION 686 VIDEO DECODER DESCRIPTION 686.01.01 GENERAL A. This specification describes the functional, performance, environmental, submittal, documentation, and warranty requirements, as well as the

More information