Sealed Circular LC Connector System Plug

Transcription

1 Sealed Crcular LC Connector System Plug Instructon Sheet Kt [ ], Receptacle Kt [ ], and EMI Receptacle Kt [ ] 07 APR 11 Plug Kt [ ] Cable Fttng Receptacle Kt [ ] EMI Receptacle Kt [ ] Plug Assembly Duplex Clp Receptacle Assembly Connector Assembly Panel Gasket Eyelets Panel Nut Protectve Covers Fgure 1 1. INTRODUCTION Ths nstructon sheet covers the termnaton of snglemode and multmode Crcular LC Plug Kt [ ], and the nstallaton of Receptacle Kt [ ] or [ ] to a panel. See Fgure 1. The sealed plug and receptacle assembles shown n Fgure 1 are used n ndustral Ethernet networks, cellular antennae, and FTTX applcatons that requre protecton from varous envronmental factors such as temporary water mmerson and/or exposure to debrs. The sealed crcular LC connector accepts tactcal cable, wth a 4.5mm mm outsde dameter and a par of 2.0mm jacketed subunts. Plug Kt [ ] contans a plug assembly wth cable fttng, duplex clp, two eyelets, two LC connector assembles, and protectve covers. See Fgure 1. Receptacle Kts [ ] and [ ] nclude a receptacle assembly, a panel gasket, and a panel nut. See Fgure 1. Read these nstructons thoroughly before startng the assembly. Dmensons n ths document are n metrc unts. Fgures and llustratons are for reference only and are not drawn to scale. The followng are requred for the assembly of the connector: S PRO--CRIMPER* Hand Tool Assy S De Set S 19mm wrench S 19mm torque wrench (N--m or n--lbs) S Strp Template S Cable strppng tool S Sharp Scssors S Instructon Sheet and fber optc connector termnaton toolng. 2. ASSEMBLY PROCEDURE 2.1. Assembly of the Plug Connector 1. Slde the plug assembly over the fber jacket as shown n Fgure Usng a pen, mark the outer jacket at the 60mm breakout length as shown n Fgure Workng n sectons, slt and remove the outer jacket to the breakout mark. E2011 Tyco Electroncs Corporaton, a TE Connectvty Ltd. Company All Rghts Reserved *Trademark TOOLING ASSISTANCE CENTER PRODUCT INFORMATION Ths controlled document s subject to change. For latest revson and Regonal Customer Servce, vst our webste at TE Connectvty, TE connectvty (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of ther respectve owners. 1 of 5 LOC B

2 Fgure 2 Fgure 6 8. Usng a sharp scssors, carefully cut two slts (8mm long) on each jacket. See Fgure 7. Usng a buffer strpper, strp off the buffer n at least three peces. Usng a clean, lnt--free cloth (soaked n alcohol), remove any resdue from the fber. Fgure 3 4. Usng shears, cut the strength members and fller flush wth the jacket. See Fgure 4. Fgure 4 5. Usng the template, mark both the 2.0mm jacketed subunts at the 27mm mark and the 8mm cable slt mark. See Fgure 5. Fgure 7 9. Carefully fan back the jacket and strength members, then slde the eyelet over the strength members as shown n Fgure 8. Fgure 5 6. Remove the jacket of each subunt to the 27mm mark wth a strp tool. 7. Usng a strp template, mark each 900 m buffer at15.5mm as llustrated n Fgure 6. Fgure After the fber has been nserted nto the connector ferrule, carefully slde the eyelet rearward to unfurl the slt jacket and strength members. Unformly dstrbute the aramd and poston the slt jacket over the rear body. 2 of 5

3 Refer to Instructon Sheet , Sectons 3.4 and 3.5 for epoxy nstructons. 11. Whle holdng the connector, push the eyelet forward, as shown n Fgure 9. Fgure 11 Be sure to observe the correct fber polarty. Fgure Place the connectors n the plug assembly as shown n Fgure 12. Properly poston the eyelet before crmpng. See Fgure 10. Fgure Depress both latches and push the connectors nto the plug assembly untl t bottoms. See Fgure 13. You wll hear an audble clck. Fgure Usng PRO--CRIMPER hand tool and crmpng de set , crmp the eyelet onto the strength members and jacket. Refer to Instructon Sheet Sectons 3.7, 3.8, and 3.10 for epoxy curng, cleavng and polshng nstructons. 13. Snap the connectors nto the duplex clp as shown n Fgure 11. Fgure 13 3 of 5

4 16. Fgure 14 shows properly postoned connectors. Note that the latches are depressed. Fgure Usng two 19mm wrenches, tghten the cable fttng to N--m [ n--lbs]. See Fgure 15. Fgure Push the loop past the nut untl t snaps nto the groove, as shown n Fgure 18. Fgure The fnshed assembly should appear as shown n Fgure 16. Fgure The properly nstalled protectve cover should appear as shown n Fgure 19. Fgure Assembly of the Plug Protectve Cover Assembly 1. Open the loop on the lanyard and slde t over the plug nut as shown n Fgure 17. Fgure Assembly of the Receptacle Kt The recommended panel cutout s shown n Fgure of 5

5 Recommended Panel Cutout Maxmum Panel Thckness: 3.18 mm [.125 n.] mm [1.07 n.] Flat Edge (Customer Located) mm [ n.] 2. Tghten the nut to a torque of 2.26 N--m [20 n--lbs] usng a 32mm wrench Assembly of the Receptacle Protectve Cover 1. Install the receptacle as descrbed n the prevous paragraph. 2. Push the loop of the lanyard over the receptacle assembly untl t snaps nto the groove of the receptacle. See Fgure 23. Note: Not to Scale / mm [ / n.] Fgure 20 The receptacle assembly conssts of the receptacle, a seal (panel gasket), and a panel nut. Refer to Fgure21. Fgure 23 The properly nstalled receptacle and protectve cover should appear as shown n Fgure 24. Fgure Insert the receptacle through the panel. See Fgure 22. It s mportant that the panel gasket s on the opposte sde of the panel from the nut. Fgure REVISION SUMMARY Fgure 22 S Updated document to corporate requrements S New logo 5 of 5