Operating Instructions for PMT Tube P3
|
|
|
- Marvin Shon Martin
- 5 years ago
- Views:
Transcription
1 Discovery Way, Acton, MA 07 Phone: (97)3-3, Fax: (97)3-0 Web Site: Operating Instructions for PMT Tube P3 Ver.0
2 PHOTOMULTlPLlER TUBE R mm (-/ Inch) Transmission Mode S Photocathode, Side on Type FEATURES Wide Photocathode High Infrared Sensitivity Excellent Spatial Uniformity Fast Time Response APPLICATIONS Near Infrared Spectrophotometer Raman Spectrophotometer Photo Luminescence Measurement GENERAL Parameter Description Unit Spectral Response Wavelength of Maximum Response Photocathode MateriaI Minimum Effective Area Window Material 00 to 0 nm 00 nm Dynode Structure Circular-cage Number of Stages 9 Direct Interelectrode Capacitances Anode to Last Dynode Anode to All Other Electrodes Base SuitabIe Socket Applicable Socket Assembly Ag O Cs (H) (W) Borosilicate glass mm. pf 3. pf -pin base JEDEC No. B- E7 A (option) E77 (option) Figure : Electron Trajectories PHOTOELECTRONS nd DYNODE LIGHT PHOTOCATHODE GLASS BULB FOCUSING ELECTRODES st DYNODE 3rd DYNODE TPMSC0003EB Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. 99 Hamamatsu Photonics K.K.
3 PHOTOMULTlPLlER TUBE R MAXIMUM RATINGS (Absolute Maximum Values) Supply Voltage Between Anode and Cathode Between Anode and Last Dynode Average Anode Current A CHARACTERISTlCS (at ) 0 0. Cathode Sensitivity Quantum Efficiency at nm 0.0 Luminous B Radiant at 00nm. Anode Sensitivity Luminous C Parameter Value Unit Parameter Gain C 3.0 Anode Dark Current D 30 (after 30min. storage in the darkness) Time Response Anode Pulse Rise Time E Electron Transit Time F Vdc Vdc ma Min. Typ. Max. Unit % A/lm ma/w A/lm na ns ns NOTES A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of K. Supply voltage is volts between the cathode and all other electrodes connected together as anode. C: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table below. Table :Voltage Distribution Ratio Electrodes K Dy Dy Dy3 Dy Dy Dy Dy7 Dy Dy9 P Ratio SuppIy Voltage : Vdc K : Cathode, Dy : Dynode, P : Anode D: Measured at the voltage which gives anode luminous sensitivity of A/lm. E: The rise time is the time for the output pulse to rise from % to 90% of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. F: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitude. In measurement, the whole photocathode is illuminated. Figure : Typical Spatial Uniformity X-Axis Y-Axis Y X SPOTSIZE : mm DIA SUPPLY VOLTAGE : 0V WAVELENGTH : 00nm RELATIVE SENSITIVITY (%) RELATIVE SENSITIVITY (%) DISTANCE FROM CENTER OF PHOTOCATHODE (mm) DISTANCE FROM CENTER OF PHOTOCATHODE (mm) TPMSB00EA
4 Figure 3: Typical Spectral Response Figure : Typical Time Response TPMSB00EA 0 TPMSB00EA CATHODE RADIANT SENSITIVITY (ma/w) QUANTUM EFFICIENCY (%) QUANTUM EFFICIENCY CATHODE RADIANT SENSITIVITY TIME (ns) 0 0 TRANSIT TIME RISE TIME WAVELENGTH (nm) SUPPLY VOLTAGE (V) Figure : Typical Gain and Anode Dark Current Figure : Typical Temperature Characteristics of Anode Dark Current (at A/lm) 7 TPMSB003EA 3 3 TPMSB00EA GAIN 3 GAIN DARK CURRENT 7 ANODE DARK CURRENT (A) ANODE DARK CURRENT (A) SUPPLY VOLTAGE (V) TEMPERATURE ( )
5 PHOTOMULTlPLlER TUBE R Figure 7: Dimensional Outline and Basing Diagram (Unit: mm) MIN. PHOTOCATHODE MIN MAX. 90MAX. DY DY 7 DY7 DY DY DY3 3 9 DY9 DY P DY K DIRECTION OF LIGHT BOTTOM VIEW (BASING DIAGRAM) 3MAX. PIN BASE JEDEC No. B- HA COATING TPMSA003EA Figure : Optional Accessories (Unit: mm) Socket E7-A D Type Socket Assembly E HOUSING (INSULATOR) POTTING COMPOUND PMT P DY9 DY DY7 DY DY DY DY3 DY DY K SOCKET PIN No R R9 R R7 C3 C C SIGNAL GND SIGNAL OUTPUT RG-7/U (BLACK) POWER SUPPLY GND AWG (BLACK) R R to R : 330k C to C3 : 0.0 F R R R3 R R HV AWG (VIOLET) R to R : 330k C to C3 : 0.0 F TACCA000ED TACCA000EB Hamamatsu also provides C900 series compact high voltage power supplies and C70 series DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply. Warning Personal Safety Hazards Electrical Shock Operating voltages applied to this device present a shock hazard. HAMAMATSU PHOTONICS K.K., Electoron Tube Center 3-, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 3-093, Japan, Telephone: ()39/-, Fax: ()39/- U.S.A.: Hamamatsu Corporation: 3 Foothill Road, Bridgewater. N.J , U.S.A., Telephone: () , Fax: ()90-3- Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr., D- Herrsching am Ammersee, Germany, Telephone: (9)-37-0, Fax: (9)- France: Hamamatsu Photonics France S.A.R.L.:, Rue du Saule Trapu, Parc du Moulin de Massy, 9 Massy Cedex, France, Telephone: (33) , Fax: (33) United Kingdom: Hamamatsu Photonics UK Limted: Lough Point, Gladbeck Way, Windmill Hill, Enfield, Middlesex EN 7JA, United Kingdom, Telephone: ()-37-3, Fax: ()-37-3 North Europe: Hamamatsu Photonics Norden AB: Färögatan 7, S--0 Kista Sweden, Telephone: () , Fax: () Italy: Hamamatsu Photonics Italia: S.R.L.: Via Della Moia, /E, 0 Arese, (Milano), Italy, Telephone: (39) , Fax: (39)-93 7 TPMSE03 JUL. 99
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOC ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
New product of near infrared (to 900 nm) detection
WITH THERMOELECTRIC COOLER H7844 New product of near infrared (to 900 nm) detection FEATURES A newly developed high sensitivity multialkali side-on photomultiplier tube Fast cooling (3 minutes) by thermoelectric
Compact size (16 mm diameter, 12 mm seated length), Fast Time response (rise time 0.78 ns)
METAL ACKAGE HOTOMULTILIER TUBE R7400U SERIES Compact size (6 mm diameter, 2 mm seated length), Fast Time response (rise time 0.7 ns) The R7400U series is a subminiature photomultiplier tube with a 6 mm
UV-LED MODULE. UV Irradiation Intensity Distribution Graphs
UV-LED MODULE UV Irradiation Intensity Distribution Graphs Product Lineup Lens Lineup Product Lineup LED DRIVER C1559-1 LED HEAD UNIT L1561/L196 SERIES standard type standard type high power type high
Applications. l Image input devices l Optical sensing devices
IMAGE SENSOR CMOS linear image sensor S8377/S8378 series Built-in timing generator and signal processing circuit; single 5 V supply operation S8377/S8378 series is a family of CMOS linear image sensors
Photon counting module
Photon counting module Fiber coupling type, low-light-level detection The is a photon counting module that can detect low-level light. It consists of a TE-cooled single pixel photon counter (SPPC), signal
High-speed photodiodes (S5973 series: 1 GHz)
S5973 series High-speed photodiodes (S5973 series: 1 GHz), and S5973 series are high-speed Si PIN photodiodes designed for visible to near infrared light detection. These photodiodes provide wideband characteristics
Parameter Specification Unit Photosensitive area mm Package Glass epoxy - Seal material Epoxy resin -
COB type, applicable to lead-free solder reflow The is a Si PIN photodiode for visible to near infrared range and is compatible with lead-free solder reflow processes. The small and thin leadless package
Parameter Specification Unit Photosensitive area mm Package Glass epoxy - Seal material Silicone resin -
COB type, applicable to lead-free solder reflow The is a for visible to near infrared range and is compatible with lead-free solder reflow processes. The small and thin leadless package allows reducing
Compact MCP-PMT Series Featuring Variety of Spectral Response with Fast Time Response QE=20% QE=10% QE=5% QE=1% -59 QE=0.1%
MICROCHANNEL PLATE- PHOTOMULTIPLIER TUBE (MCP-PMTs) SERIES Compact MCP-PMT Series Featuring Variety of Spectral Response with Fast Time Response FEATURES High Speed Rise Time: 1ps T.T.S. (Transit Time
PHOTOTUBES FEATURES AND APPLICATIONS GLOSSARY OF TERMS FEATURES SPECTRAL RESPONSE RANGE AND APPLICATIONS
Phototubes PHOTOTUBES FEATURES AND APPLICATIONS FEATURES High sensitivity and high stability Wide dynamic range Superior temperature stability Large photosensitive area Low voltage operation SPECTRAL RESPONSE
Near infrared image sensor (0.9 to 1.7 µm) with high-speed data rate
IMAGE SENSOR InGaAs linear image sensor G99-56D/-5D Near infrared image sensor (.9 to.7 µm) with high-speed data rate HAMAMATSU provides high-speed, near infrared image sensors designed for detectors used
Short wavelength type APD. Effective photosensitive area (mm) Effective photosensitive area size* 2
Short wavelength type APD Features High sensitivity at visible range Low noise High gain Low capacitance Applications Low-light-level measurement Analytical instrument Structure / Absolute maximum ratings
APD modules. Operates an APD with single 5 V supply (standard type, short-wavelength type) C12702 series.
Operates an APD with single 5 V supply (standard type, short-wavelength type) Features Includes a high-sensitivity APD Uses a Hamamatsu high-sensitivity Si APD. Four types are available with different
Reverse voltage VR max. Electrical and optical characteristics (Typ. Ta=25 C, unless otherwise noted) Short. Temp. S coefficient (A/W) of
Ceramic package photodiodes with low dark current The are ceramic package photodiodes that offer low dark current. Ceramic package used is light-impervious, so no stray light can reach the photosensitive
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
Photosensitive area size (mm) Reverse voltage VR max (V) R to +60
,, 6 to 37 mm resistance length PSD for precision distance measurement Hamamatsu provides various types of one-dimensional PSD (position sensitive detector) designed for precision distance measurement
Effective photosensitive* 2 area size. Storage temperature Tstg (mm) ( C) ( C) S φ0.2 φ0.5 S φ to to +100 S9075
/-05/-10, S5344, S5345 Short wavelength type APD, for 600 nm band These are short wavelength APDs with improved sensitivity in the UV to visible range. They offer high gain, high sensitivity, and low noise
M=100, RL=50 Ω λ=800 nm, -3 db
Low bias operation, for 800 nm band, small package Features Miniature and thin package:.8 3..0 t mm Stable operation at low bias High-speed response High sensitivity Low noise Applications Optical rangefinder
Peak emission wavelength: 4.3 μm
Peak emission wavelength: 4.3 μm The is a mid infrared LED with a 4.3 μm peak emission wavelength. It is a product that has been achieved using Hamamatsu unique crystal growth technology and process technology.
Low bias operation, for 800 nm band
Low bias operation, for 800 nm band These are 800 nm band near-infrared Si APDs that can operate at low voltages, 200 V or less. They are suitable for applications such as FSO (free space optics) and optical
Effective photosensitive area. Photosensitive area size
High performance, high reliability Si PIN photodiodes The is a high-speed Si PIN photodiode having high sensitivity over a wide spectral range from visible to near infrared light. The provides high performance
Si photodiode. Applicable to lead-free solder reflow and wide temperature range. S9674. Absolute maximum ratings
Applicable to lead-free solder reflow and wide temperature range The is a photodiode that is applicable to lead-free solder reflow and has an extremely wide operating and storage temperature range (-40
Si PIN photodiodes. High-speed detectors with plastic package. Structure. Absolute maximum ratings
High-speed detectors with plastic package The and are high-speed APC (auto power control) detectors developed for monitoring laser diodes with a peak wavelength of 66 nm or 78 nm. The is designed for surface
Signal processing circuit for 1-D PSD
Signal processing circuit for 1-D PSD Circuit board for easier 1-D PSD operation The is a DC signal processing circuit for one-dimensional PSD. It is suitable for displacement measurements using DC light.
Si PIN photodiodes. High-speed detectors with plastic package. Structure. Absolute maximum ratings
High-speed detectors with plastic package The and are high-speed APC (auto power control) detectors developed for monitoring laser diodes with a peak wavelength of 66 nm or 78 nm. The is designed for surface
Variable gain and stable detection even at high gains
MODULE APD module C5 Variable gain and stable detection even at high gains Along with an APD, current-to-voltage conversion circuit, and high-voltage power supply circuit, the C5 contains a microcontroller
Signal processing circuit for 1-D PSD
Signal processing circuit for 1-D PSD Circuit board for easier 1-D PSD operation The is a DC signal processing circuit for one-dimensional PSD. It is suitable for displacement measurements using DC light.
Effective photosensitive area (mm) Photosensitive area size
High UV resistance, photodiodes for UV monitor The are Si photodiodes that have achieved high reliability for monitoring ultraviolet light by employing a structure that does not use resin. They exhibit
Peak emission wavelength: 3.9 μm
Peak emission wavelength: 3.9 μm The is a high-output mid-infrared LED with a 3.9 µm peak emission wavelength. It is a product that has been achieved using Hamamatsu unique crystal growth technology and
Applications. Photosensitive area size. Storage temperature Tstg (mm) (mm 2 ) (V) ( C) ( C) S
, etc. Photodiodes molded into clear plastic packages These are Si photodiodes molded into clear plastic packages. Two types are available with sensitivity in the visible range and in the visible to near
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
Signal processing circuit for 2-D PSD
Signal processing circuit for 2-D PSD Circuit board for easier 2-D PSD operation The is a DC signal processing circuit for two-dimensional PSD. It is suitable for displacement measurements using DC light.
Parameter Symbol Specification Unit Photosensitive area - ɸ0.8 mm Package mm
Surface mount type, high-speed Si photodiode The is a Si PIN photodiode with sensitivities in the visible to near infrared range and is compatible with lead-free solder reflow. It features high-speed response
Non-discrete position sensors utilizing photodiode surface resistance
Twodimensional PSD Nondiscrete position sensors utilizing photodiode surface resistance PSD (position sensitive detector) is an optoelectronic position sensor utilizing photodiode surface resistance. Unlike
MPPC (multi-pixel photon counter)
MPPC (multi-pixel photon counter) Low afterpulses, wide dynamic range, for high-speed measurement Photosensitive area: 1 1 mm These MPPCs utilize very small pixels arrayed at high densities to achieve
These Si photodiodes have sensitivity in the UV to near IR range. They are suitable for low-light-level detection in analysis and the like.
UV to near IR for precision photometry These Si photodiodes have sensitivity in the UV to near IR range. They are suitable for low-light-level detection in analysis and the like. Features High sensitivity
MPPC modules. MPPC array modules for very-low-level light detection, 16 ch analog output. C13368/C13369 series (Analog output type)
MPPC modules C13368/C13369 series (Analog output type) MPPC array modules for very-low-level light detection, 16 ch analog output The C13368/C13369 series (analog output type) is an optical measurement
Signal processing circuit for 2-D PSD
Signal processing circuit for 2-D PSD Circuit board for easier 2-D PSD operation The is a DC signal processing circuit for two-dimensional PSD. It is suitable for displacement measurements using DC light.
Photo IC diode. Wide operating temperature: -40 to +105 C. S MT. Absolute maximum ratings (Ta=25 C)
Wide operating temperature: -40 to +05 C The photo IC has a spectral response close to human eye sensitivity. Two active areas are made on a single chip. Almost only the visible range can be measured by
Optics modules. Absorbance measurement module with built-in photodiode array, optical elements, current-tovoltage. C13398 series.
Absorbance measurement module with built-in photodiode array, optical elements, current-tovoltage converter, etc. The is an optics module for absorbance measurement featuring high blocking performance
APD modules. APD module integrated with peripheral circuits. C12703 series. Selection guide. Block diagram
APD module integrated with peripheral circuits Features Uses a high sensitivity APD Two types of APDs with different photosensitive areas (φ1.5 mm, φ3. mm) are provided. On-board high sensitivity circuit
RGB color sensor. Effective photosensitive area. Green, Red: 2.25 Blue : 4.5
Si photodiodes S6428-01 S6429-01 S6430-01 RGB color sensor The S6428-01, S6429-01 and S6430-01 are color sensors designed to respectively detect monochromatic colors of blue (λp=460 nm), green (λp=540
1-D PSD with small plastic package
1D PSD with small plastic package Hamamatsu offers a variety of 1D PSDs (position sensitive detectors) molded into plastic packages. These PSDs feature excellent position detection resolution, high resistance
16-element Si photodiode arrays
S11212-421 S11212-321 S11212-021 S11212-121 Back-illuminated photodiode arrays for non-destructive inspection The is a back-illuminated type 16-element photodiode array specifically designed for non-destructive
Driver circuit for MPPC
Simple evaluation starter kit for non-cooled s The is a starter kit designed for simple non-cooled evaluations. It consists of a sensor board and a power supply board. The sensor board includes an socket
InAsSb photovoltaic detectors
High-speed response and high sensitivity in the spectral band up to 11 μm Infrared detectors The are photovoltaic type infrared detectors that have achieved high sensitivity in the spectral band up to
Photosensor with front-end IC
Compact APD suitable for various light level detection The is a compact optical device that integrates a Si APD and preamp. It has a built-in DC feedback circuit for reducing the effects of background
InAsSb photovoltaic detector
InAsSb photovoltaic detector P12691-21 High-speed response and high sensitivity in the 8 μm spectral band Thermoelectrically cooled infrared detector with no liquid nitrogen required The P12691-21 is an
Infrared detector modules with preamp
Easy-to-use detector modules with built-in preamps Infrared detector modules operate just by connecting to DC power supplies. The detector element is selectable from among InGaAs, InAs, InSb, and InAsSb
Phototubes. Phototubes, Solar Blind Phototubes and Biplanar Phototubes
Phototubes Phototubes, Solar Blind Phototubes and Biplanar Phototubes FEATURES AND APPLICATIONS FEATURES AND APPLICATIONS OF PHOTOTUBES FEATURES High-speed response Choice of spectral response High sensitivity
Peak sensitivity wavelength λp (nm) Photosensitive area (mm)
Integrates a -PSD for precision photometry or a 4-segment Si photodiode with low-noise amp in a compact case PSD modules contain a high-precision two-dimensional PSD (position sensitive detector) or a
Suppressed IR sensitivity
For UV to visible, precision photometry; suppressed IR sensitivity These Si photodiodes have suppressed IR sensitivity. They are suitable for low-light-level detection in analysis and the like. Features
InGaAs multichannel detector head
Near infrared line camera (Line rate: 31.25 khz) The is a multichannel detector head suitable for applications where high-speed response is required, such as SD- OCT (spectral domain-optical coherence
Applications. Number of terminals. Supply voltage (op amp) Vcc
PHOTODIODE Si photodiode with preamp S5590, S559 Photodiode and preamp integrated with feedback resistance and capacitance S5590, S559 are lownoise light sensors consisting of a large area Si photodiode,
Photo IC diode. Plastic package shaped the same as metal package. S SB. Absolute maximum ratings (Ta=25 C)
Plastic package shaped the same as metal package The photo IC has spectral response close to human eye sensitivity. Two photosensitive areas are made on a single chip. Almost only the visible range can
Photosensitive area (mm) 4 4. Peak sensitivity wavelength (nm) Supply voltage Dark state. Max. Vcc max. Tstg Min. Max. (ma) (V)
Integrates a PSD for precision photometry or a 4-segment Si photodiode with low-noise amp in a compact case PSD modules contain a high-precision two-dimensional PSD (position sensitive detector) or a 4-segment
NMOS linear image sensor
Image sensor highly sensitive to X-rays from 0 k to 00 kev s are self-scanning photodiode arrays designed specifically as detectors for multichannel spectroscopy. The scanning circuit is made up of N-channel
Driver circuit for CCD linear image sensor
Driver circuit for CCD linear image sensor C11165-01 For CCD image sensor (S11155/S11156-2048-01) The C11165-01 is a driver circuit designed for HAMAMATSU CCD image sensor S11155/S11156-2048-01. The C11165-01
16-element Si photodiode arrays
S11299-321 S11299-421 S11299-21 S11299-121 Back-illuminated photodiode arrays for X-ray non-destructive inspection, slender board type The is a back-illuminated type 16-element photodiode array specifically
InAsSb photovoltaic detector
InAsSb photovoltaic detector P2-2 High-speed response and high sensitivity in the 5 μm spectral band Thermoelectrically cooled infrared detector with no liquid nitrogen required The P2-2 is an infrared
MPPC (Multi-Pixel Photon Counter)
S13362-35DG Significantly reduced crosstalk, low afterpulses The can reduce dark count by cooling in addition to low afterpulses and low crosstalk of the S1336 series. The integrates the S1336 series with
Power supply for MPPC
Power supply for MPPC C1104-0 Bias power supply with built-in high precision temperature compensation for MPPCs The C1104-0 is a high voltage power supply that is optimized for MPPCs (multi-pixel photon
MS series. Parameter Min. Typ. Max. Unit Driving voltage V Power consumption mw Video rate khz
Mini-spectrometer MS series C10MA Ultra-compact Mini-spectrometer integrating MEMS and technologies The MS series C10MA is a thumb-sized (2. 13 1. mm) spectrometer head developed for installation into
CMOS linear image sensors
Built-in timing generator and signal processing circuit; 5 V single supply operation The is a family of CMOS linear image sensors designed for image input applications. These linear image sensors operate
PbSe photoconductive detectors
PbSe photoconductive detectors P9696 series P327-8 Infrared detectors with fast response and high sensitivity in 5 μm wavelength band Compared to other detectors used in the same wavelength regions, PbSe
Effective photosensitive area (mm)
Chip carrier package for mount The, S5107, and S7510 are Si PIN photodiodes sealed in chip carrier packages suitable for mount using automated solder reflow techniques. These photodiodes have large photosensitive
16-element Si photodiode arrays
Back-illuminated photodiode arrays for X-ray nondestructive inspection (element pitch: mm) The is a back-illuminated type 16-element photodiode array specifically designed for non-destructive X- ray inspection.
Photo IC diode. Plastic package shaped the same as metal package. S SB. Features. Applications
Plastic package shaped the same as metal package The photo IC has spectral response close to human eye sensitivity. Two photosensitive areas are made on a single chip. Almost only the visible range can
Photo IC diode. COB (chip on board) type, small package. S CT. Absolute maximum ratings
COB (chip on board) type, small package mm The photo IC has spectral response close to human eye sensitivity. Two photosensitive areas are made on a single chip. Almost only the visible range can be measured
16-element Si photodiode arrays
Back-illuminated photodiode arrays for X-ray nondestructive inspection (element pitch: mm) The is a back-illuminated type 16-element photodiode array specifically designed for non-destructive X-ray inspection.
Driver circuit for InGaAs linear image sensor
Driver circuit for InGaAs linear image sensor [G11620 series (non-cooled type)] The is a driver circuit developed for InGaAs linear image sensors [G11620 series (non-cooled type)]. The driver circuit consists
Driver circuit for CCD linear image sensor
For CCD image sensor (S11151-2048) The is a driver circuit designed for Hamamatsu CCD image sensor S11151-2048. The can be used in spectrometers when combined with the S11151-2048. The holds a CCD driver
Driver circuit for CMOS linear image sensor
Driver circuit for CMOS linear image sensor C13015-01 For CMOS linear image sensor S11639-01, etc. The C13015-01 is a driver circuit developed for Hamamatsu CMOS linear image sensor S11639-01, etc. By
MCT photoconductive detectors
Non-cooled type and suitable for long, continuous operation Features Choice of spectral response (up to 12 μm) The band gap can be adjusted by controlling the composition ratio of HgTe and CdTe. Utilizing
Driver circuits for CCD image sensor
Driver circuit for CCD image sensor (S10420/S11071/S11510 series) The and are driver circuits designed for HAMAMATSU CCD image sensor S10420/S11071/S11510 series. The and can be used in spectrometer when
InAsSb photovoltaic detectors
High-speed response and high sensitivity in the spectral band up to 5 μm Infrared detectors The are photovoltaic type infrared detectors that have achieved high sensitivity in the spectral band up to 5
APD module. Variable gain, stable detection even at high gain. C Applications. Features. Sensitivity vs.
APD module C158-1 Variable gain, stable detection even at high gain The C158-1 consists of an APD, current-to-voltage converter, high-voltage power supply circuit as well as a microcontroller for compensating
Application OCT. Dimensions (mm) Weight (g) Operating temperature* 1 Storage temperature* 1 λ=1.55 μm (V) (mw)
Balanced detectors with reduced multiple reflections These are differential amplification type photoelectric conversion modules containing two Hamamatsu photodiodes with balanced characteristics. The photodiodes
Designed for back-thinned CCD area image sensor
IMAGE SENSOR CCD multichannel detector head C00, C0 Designed for back-thinned CCD area image sensor C00 and C0 are high sensitivity multichannel detector heads for use with back-thinned FFT-CCD area image
MPPC (Multi-Pixel Photon Counter) arrays
MPPC (Multi-Pixel Photon Counter) arrays MPPC arrays in a chip size package miniaturized through the adoption of TSV structure The is a MPPC array for precision measurement miniaturized by the use of TSV
Power supply for MPPC
Power supply for MPPC C1104-0 Bias power supply with built-in high precision temperature compensation for MPPCs The C1104-0 is a high voltage power supply that is optimized for MPPCs (multi-pixel photon
InGaAs PIN photodiode arrays
16/32/46 element InGaAs array for near IR detection The is one-dimensional InGaAs PIN photodiode array in a ceramic DIP (dual inline package). It can be used to perform simple spectroscopic analysis. Features
MCT photoconductive detectors
MCT photoconductive detectors P3257 series P4249-08 0 μm band infrared detector with high sensitivity and high-speed response Features High-speed response, high sensitivity in the 0 μm band detection Photoconductive
Driver circuit for CCD linear image sensor
Driver circuit for CCD linear image sensor C11165-02 For CCD image sensor (S11155/S11156-2048-02) The C11165-02 is a driver circuit designed for Hamamatsu CCD image sensor S11155/S11156-2048-02. The C11165-02
Accessories for infrared detector
Temperature controllers Heatsinks for TE-cooled detector Chopper, etc. Wide lineups of accessories for infrared detector HAMAMATSU provides temperature controllers, heatsinks for TE-cooled detector, chopper
Driver circuit for CMOS linear image sensor
High-precision driver circuit with variable integration time function The is a driver circuit specifically designed for the Hamamatsu S10111 to S10114 series, S10121 to S10124 series (-01) current-output
Compact MCP-PMT Series Featuring Variety of Spectral Response with Fast Time Response MIRROR MIRROR QE = 0.1%
MICROCHANNEL PLATE- PHOTOMULTIPLIER TUBE (MCP-PMTs) R3809U-50 SERIES Compact MCP-PMT Series Featuring Variety of Spectral Response with Fast Time Response FEATURES High Speed Rise Time: 150 ps T.T.S. (Transit
MPPC (Multi-Pixel Photon Counter)
MPPC (Multi-Pixel Photon Counter) MPPCs in a chip size package miniaturized through the adoption of TSV structure The are MPPCs for precision measurement miniaturized by the use of TSV (through-silicon
CMOS linear image sensor
Digital output, built-in 8/10-bit A/D converter, single power supply operation The is a CMOS linear image sensor designed for image input applications. The signal processing circuit has a charge amplifier
LCOS-SLM (Liquid Crystal on Silicon - Spatial Light Modulator)
POWER LCOS-SLM CONTROLLER RESET POWER OUTPUT ERROR LCOS-SLM (Liquid Crystal on Silicon - Spatial Light Modulator) Control your light! Shape your beam! Improve your image! The devices are a reflective type
Driver circuit for InGaAs linear image sensor
(G11135 series, G14006-512DE) The is a driver circuit developed for InGaAs linear image sensors (G11135 series, G14006-512DE). The driver circuit consists of an analog video signal processing circuit (16-bit
Mini-spectrometers. TM series. High sensitivity type (integrated with backthinned type CCD image sensor) C10082CA/C10083CA series
C12CA/C1CA series type (integrated with backthinned type CCD ) mini-spectrometers are polychromators integrated with optical elements, an and a driver circuit. Light to be measured is guided into the entrance
Reduced color temperature errors
Reduced color temperature errors The is a photo IC diode with spectral response characteristics that closely resemble human eye sensitivity. Two active areas are formed on the same chip, and the outputs
Driver circuits for photodiode array with amplifier
C98 series Compact, easytouse driver circuit The C98 series CMOS driver circuit is designed for photodiode arrays with amplifier. The C98 series operates a linear image sensor by just inputting two signals
Between elements measure. Photosensitive area (per 1 element)
16, 35, 46 element Si photodiode array for UV to NIR The are Si photodiode linear array mounted in ceramic DIPs (Dual Inline Packages). These photodiode arrays are primarily developed for low-light-level
Mini-spectrometers. RC series. Compact and low cost C11009MA, C11010MA: for installation into measurement equipment.
Compact and low cost, : for installation into measurement equipment HAMAMATSU mini-spectrometer is a family of compact polychromators integrated with a reflection grating and a CMOS linear. Two types are
Mini-spectrometer. SMD series C14384MA-01. High sensitivity in the near infrared region (to 1050 nm), ultra-compact grating type spectrometer
Mini-spectrometer SMD series C14384MA-01 High sensitivity in the near infrared region (to 1050 nm), ultra-compact grating type spectrometer The C14384MA-01 is a ultra-compact grating type spectrometer
12-bit digital output
S02-0C 2-bit digital output The S02-0C is a digital color sensor sensitive to red (λ=65 nm), green (λ= nm) and blue (λ=465 nm) regions of the spectrum. Detected signals are serially output as 2-bit digital
NMOS multichannel detector head
UV to near infrared range (200 to 1000 nm), For multichannel spectrophotometry The is a family of multichannel detectors developed for spectrophotometry in the UV to near infrared range (up to 1000 nm).