Coaxial Cable Termination
|
|
- Loreen Holmes
- 3 years ago
- Views:
Transcription
1 Coaxial Cable Termination RF one-step BNC/TNC connectors Applications RF one-step BNC/TNC connectors are single-piece assemblies for terminating the center conductor and the braid of a broad range of coaxial cables. The connectors are fully intermateable with MIL-C connectors and are available in 50-ohm and 75-ohm versions. Features and benefits Easy, quick installation. Outstanding cable-retention force. Solder-solder connection type (center conductor and braid). One-step termination for easy, quick installation and lower installed cost. Exceptional cable retention force to withstand high vibration and frequent mates and demates. Fully soldered center conductor and braid. Excellent built-in strain relief against vibration and excessive handling. Long-term reliability. Controlled soldering termination. Use with standard RG/U cables and Raychem Cheminax cables. Three product sizes to accommodate a wide range of cables. Meets performance requirements of MIL-C up to 2.8 GHz. Available in: Americas Europe Asia Pacific Specifications Installation Raychem For proper installation of these devices, Refer to Raychem installation procedure RB-115 the correct heating tool and reflector RPIP for detailed instructions. attachment must be used. Any one of the following Raychem heating tools is recommended: Steinel Model HL1802E CV Electrical Interconnect Products
2 Fax-on-demand US only (800) Outside US (650) Visit our website at Product options and part numbering system (mm/in) Connector style Dash No. Style Connector type RXX - XX - X - XX -XX TNC BNC -00 Straight plug 24.5 max. (.965) 24.5 max. (.965) -01 Right angle plug 33.5 max. (1.32) 31.5 max. (1.23) 28 (1.09) 28 (1.09) Male -02 Straight bulkhead jack -03 Straight jack -04 Straight panel jack Female Connector size L = Large M = Medium S = Small 4 x M2.5 x x M2.5 x = 50 ohms 75 = 75 ohms D = Nickel-plated brass body, gold-plated brass pin B = BNC T = TNC Example: RBD-50-L-00 is a BNC connector, 50 ohms, large size, with straight plug body. Users should independently evaluate the suitability of the product for their application. Before ordering check with factory for most current data Electrical Interconnect Products
3 Coaxial Cable Termination RF one-step BNC/TNC connectors (cont d.) Product characteristics Solder Transition Center contact Dielectric insulator Connector body Material Center contact Dielectric insulator Transition Connector body Solder and flux Braided shield Insulation sleeve Strain relief/sealing sleeve Typical performance Dielectric withstand voltage Insulation resistance Temperature rating Contact resistance-straight Contact resistance-right angle Cable retention force Voltage rating Connector durability Electrical performance Nominal impedance Frequency range Insulation sleeve Shield Insulation sleeve and solder Gold-plated beryllium copper (female) Gold-plated brass (male) PTFE Silver-plated brass Nickel-plated brass Sn63Pb37, RMA flux Tin-plated copper wire per ASTM B3 Radiation-crosslinked, heat-shrinkable polyvinylidene fluoride, transparent blue Radiation-crosslinked, heat-shrinkable modified polyolefin with adhesive, black 1500 V 5000 megohms -55C to 150C Inner = 1.5 milliohms, outer = 1.0 milliohm Inner = 2.5 milliohms, outer = 1.5 milliohms 295N (66 lb) to 822N (196 lb) 500 V RMS 500 mating cycles minimum 50 and 75 ohms Up to 2.8 GHz Part selection process 1. From Product Options and Dimensions on page 8-61, select the connector style you need (BNC or TNC, plug or jack, male or female contacts). 2. From the tables that follow, find the appropriate table for the connector style you selected. 3. From the appropriate table, select the connector part number based on the RG cable type or Raychem cable part number. For cable types not shown use the cable dimensions. Note: The cable dimensions in each table are keyed to the diagram below. D E F G 8-62 Electrical Interconnect Products
4 Fax-on-demand US only (800) Outside US (650) Visit our website at Part number selection - BNC coaxial connectors BNC straight plugs, male contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RBD-50-S-00 RG-303, RG A1311 ( ) ( ) (.118) (.050) RBD-50-M-00 RG-225, RG-214 ( ) ( ) (.287) (.100) RBD-50-L RG-179, RG A ( ) ( ) (.060) (.025) RBD-75-S-00 ( ) ( ) (.126) (.050) RBD-75-M RG-6, RG-11, RG-12, RG RG-144, RG-216 ( ) ( ) (.287) (.100) RBD-75-L-00 BNC right-angle plugs, male contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RBD-50-S-01 RG-303, RG A1311 ( ) ( ) (.118) (.050) RBD-50-M-01 RG-225, RG-214 ( ) ( ) (.287) (.100) RBD-50-L RG-179, RG A ( ) ( ) (.060) (.025) RBD-75-S A1311, 7528A ( ) ( ) (.146) (.050) RBD-75-M-01 RG-144, RG-216 ( ) ( ) (.287) (.100) RBD-75-L-01 Users should independently evaluate the suitability of the product for their application. Before ordering check with factory for most current data Electrical Interconnect Products
5 Coaxial Cable Termination RF one-step BNC/TNC connectors (cont d.) Part number selection - BNC coaxial connectors BNC straight bulkhead jacks, female contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RBD-50-S-02 RG-303, RG A1311 ( ) ( ) (.118) (.050) RBD-50-M-02 RG-225, RG-214 ( ) ( ) (.287) (.100) RBD-50-L RG-179, RG A ( ) ( ) (.060) (.025) RBD-75-S ( ) ( ) (.146) (.050) RBD-75-M RG-6, RG-11, RG-12, RG RG-144, RG-216 ( ) ( ) (.287) (.100) RBD-75-L-02 BNC straight jacks, female contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RBD-50-S-03 RG-303, RG A1311 ( ) ( ) (.118) (.050) RBD-50-M-03 RG-225, RG-214 ( ) ( ) (.287) (.100) RBD-50-L-03 ( ) ( ) (.060) (.025) RBD-75-S ( ) ( ) (.146) (.050) RBD-75-M-03 RG-144, RG-216 ( ) ( ) (.287) (.100) RBD-75-L Electrical Interconnect Products
6 Fax-on-demand US only (800) Outside US (650) Visit our website at Part number selection - BNC coaxial connectors (continued) BNC straight panel jacks, female contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RBD-50-S-04 RG-303, RG A1311 ( ) ( ) (.118) (.050) RBD-50-M-04 RG-225, RG-214 ( ) ( ) (.287) (.100) RBD-50-L-04 ( ) ( ) (.060) (.025) RBD-75-S-04 ( ) ( ) (.146) (.050) RBD-75-M-04 RG-144, RG-216 ( ) ( ) (.287) (.100) RBD-75-L-04 Part number selection - TNC coaxial connectors TNC straight plugs, male contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RTD-50-S-00 RG-303, RG A1311 ( ) ( ) (.118) (.050) RTD-50-M-00 RG-225, RG-214 ( ) ( ) (.287) (.100) RTD-50-L RG-179, RG A ( ) ( ) (.060) (.025) RTD-75-S-00 ( ) ( ) (.146) (.050) RTD-75-M-00 RG-144, RG-216 ( ) ( ) (.287) (.100) RTD-75-L-00 Users should independently evaluate the suitability of the product for their application. Before ordering check with factory for most current data Electrical Interconnect Products
7 Coaxial Cable Termination RF one-step BNC/TNC connectors (cont d.) Part number selection - TNC coaxial connectors (continued) TNC right-angle plugs, male contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RTD-50-S-01 RG-303, RG A1311 ( ) ( ) (.118) (.050) RTD-50-M-01 RG-225, RG-214 ( ) ( ) (.287) (.100) RTD-50-L-01 ( ) ( ) (.060) (.025) RTD-75-S-01 ( ) ( ) (.146) (.050) RTD-75-M-01 RG-144, RG-216 ( ) ( ) (.287) (.100) RTD-75-L-01 TNC straight bulkhead jacks, female contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RTD-50-S-02 RG-303, RG A1311 ( ) ( ) (.118) (.050) RTD-50-M-02 RG-225, RG-214 ( ) ( ) (.287) (.100) RTD-50-L RG-179, RG A ( ) ( ) (.060) (.025) RTD-75-S-02 ( ) ( ) (.146) (.050) RTD-75-M-02 RG-144, RG-216 ( ) ( ) (.287) (.100) RTD-75-L Electrical Interconnect Products
8 Fax-on-demand US only (800) Outside US (650) Visit our website at Part number selection - TNC coaxial connectors TNC straight jacks, Female contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RTD-50-S-03 RG-303, RG A1311 ( ) ( ) (.118) (.050) RTD-50-M-03 RG-225, RG-214 ( ) ( ) (.287) (.100) RTD-50-L-03 ( ) ( ) (.060) (.025) RTD-75-S-03 ( ) ( ) (.146) (.050) RTD-75-M-03 RG-144, RG-216 ( ) ( ) (.287) (.100) RTD-75-L-03 TNC straight panel jacks, female contacts RG-196,RG A1317 ( ) ( ) (.060) (.025) RTD-50-S-04 RG-303, RG A1311 ( ) ( ) (.118) (.050) RTD-50-M-04 RG-225, RG-214 ( ) ( ) (.287) (.100) RTD-50-L-04 ( ) ( ) (.060) (.025) RTD-75-S-04 ( ) ( ) (.146) (.050) RTD-75-M-04 RG-144, RG-216 ( ) ( ) (.287) (.100) RTD-75-L-04 Hole pattern for panel-mounted products (mm/in) 12.7 (.5) = = 12.7 (.5) RBD-XX-X-04 RTD-XX-X-04 Panel thickness: 3.2 (.125) max. = = 11.2 (.44) 3 (.12) RBD-XX-X -02 RTD-XX-X (.8) min. 12 (.47) 18 (.7) min (.51) Users should independently evaluate the suitability of the product for their application. Before ordering check with factory for most current data Electrical Interconnect Products
MCX - 75 Ohm Connectors
133-8333-001 4 133-8333-401 4 133-8334-001 4 133-8334-401 4 133-8433-001 3 133-8433-101 3 133-8434-001 3 133-8445-001* 3 133-8445-101* 3 133-8701-201 5 133-8701-211 5 133-8701-301 6 133-8701-311 6 133-8701-401
SMA - 50 Ohm Connectors
Alphabetical Index 142-0593-001 6 142-0593-006 6 142-0593-401 6 142-0593-406 6 142-0594-001 6 142-0594-006 6 142-0594-401 6 142-0594-406 6 142-0693-001 4 142-0693-006 4 142-0693-051 5 142-0693-056 5 142-0693-101
The Custom Interconnect Leader TM
LC Series.5.188.685 ELECTRICAL Nominal Impedance: Frequency Range: Voltage Rating: Dielectric Withstanding Voltage: Insulation Resistance: VSWR: 50 ohms DC to 1.0 GHz 5,000 volts rms 3,000 volts rms 5,000
Materials Connector part Material Finish
Materials Connector part Material Finish Bodies Brass Nickel or Gold Center Contact Male: Brass Gold Female: Brass, Phosphor Bronze, or Beryllium Copper Insulator Delrin or Teflon N/A Crimp ferrule Annealed
Type "N" Connectors. Type "N" Interface Dimensions
Type "N" Connectors The type N series coaxial connectors were originally designed as medium-size low voltage constant impedance 50 OHM connectors. Type N connectors found immediate popularity for microwave
TNC Connectors. RF Coax Connectors. Product Facts
Product Facts Hex Crimp and Connectors 50 and 75 ohm commercial versions available Provides excellent performance at frequencies up to 7 GHz ow cost commercial type available type is smaller and lighter
Materials Connector part Material Finish
Materials Connector part Material Finish Bodies Brass Nickel or Gold Center Contact Male: Brass Gold Female: Brass, Phosphor Bronze, or Beryllium Copper Insulator Delrin or Teflon N/A Crimp ferrule Annealed
Amphenol RF Connectors
Amphenol RF Connectors 007 901-9601 SMA PLUGS & ANGLE PLUGS FOR FLEXIBLE CABLE 50X IMPEDANCE Conn. Attachment RG-/U Outer Inner 901-9511-12SF Dbl. Braid RG-316 Plug Br. Solder $17.49 901-9531-12SF Angle
Series MCX 50 micro miniature connectors
Series MCX 50 micro miniature connectors Description Content MCX 50 HUBER+SUHNER MCX micro miniature snap-on connectors offer you an excellent blend of size,weight, durability and performance for applications
SERIES BNC 50, COAXIAL MINIATURE CONNECTORS
SERIES BNC 50, COAXIAL MINIATURE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER BNC is still one of the most popular connector series, featuring a two stud bayonet coupling mechanism, which is particularly
SMA One Piece Semi-Rigid Connectors
SMA One Piece Semi-Rigid Connectors The Johnson captivated solderless contact connectors for semi-rigid cable provide a unique solution for high frequency cable assemblers. As compared to standard solder-on
HN Connectors. Automatic Connector. Introduction. Contents. 631/ FAX 631/
Connectors Introduction 2004 Automatic Connector. All rights reserved. pdf 1.0 4-13-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable
Non Magnetic Connectors Product Catalog
Non Magnetic Connectors Product Catalog Introduction Johnson s Non-Magnetic Connector Additions Offer Solutions to MR Imaging Technology Johnson, a product line of Cinch Connectivity Solutions, has expanded
Automatic Connector MHV Connectors MHV Introduction MHV series connectors Contents Polarized mating interfaces Anti-Rock mating interfaces
Automatic s 2004 Automatic. All rights reserved. pdf 1.0 3-18-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable Plugs...................
Non Magnetic Connectors
Non Magnetic Connectors Johnson Components builds coaxial connectors using innovative materials and design to provide Mil Spec Performance at a commercial price. Now we offer our Non Magnetic Connectors
1.0/2.3 DIN 1.0/2.3 DIN 1.0/2.3 DIN. Technical Data. Microminiature Coaxial Connector. Material Data
.0/.3 DIN.0/.3 DIN Microminiature Coaxial Connector Technical Data Description The.0/.3 series are through construction and materials especially suited for instruments, where highest reliability is required,
Series SK (2.92 mm) prec. submini. connectors
Series prec. submini. connectors Description Content HUBER+SUHNER SK connectors are precision connectors for microwave applications up to 40 GHz. They are intermateable with series SMA and PC 3.5. They
MCX Miniature Coaxial Connectors
ONLINE CATALOG MCX Miniature Coaxial Connectors 104 John W. Murphy Drive P.O. Box 510 New Haven, CT 06513 www.aepconnectors.com e-mail: aepsales@aepconnectors.com Mating Interfaces MCX Miniature Coaxial
RF CONNECTORS RFC SERIES
Introduction: Adam Tech s RFC series RF connectors are a comprehensive assortment of Radio Frequency signal connectors in standard, miniature, sub-miniature, micro miniature and surface mount styles. Included
bmam connectors DIVIDER PAGE
bmam connectors DIVIDER PAGE 4 bmam interface dimensions "E" "D" REF. PLANE "E" REF. PLANE "G" "C".0 REF. 60 "C" "B" "B".0 REF. 0 "F" "D" male, plug INCHES / MILLIMETERS MINIMUM MAXIMUM LTR. IN. MM. IN.
RF/Microwave Connectors & Cable Assemblies
RF/Microwave Connectors & Cable Assemblies Emerson Network Power Connectivity Solutions Connectivity Solutions To our valued customers: For over 80 years, Johnson Components and Cambridge Products have
Series SMPM-T. Description. Compatibility. Content. Interface dimensions (mm/inches) SMPM-T male (pin contact), smooth bore
Series Description The is the smallest threaded open source connector on the market. Its unique and innovative combination of a MIL- STD-348 SMPM female interface connector together with a retractable
SUHNER QMA SUBMINIATURE CONNECTORS
SUHNER QMA SUBMINIATURE CONNECTORS Description Content Page SUHNER QMA coaxial connectors are available with 50 Ω impedance. The frequency range extends to 11 GHz, depending on the connector and cable
C Connectors. Automatic Connector. Introduction. Contents. C Interface Options. 631/ FAX 631/
utomatic onnector onnectors Introduction 2004 utomatic onnector. ll rights reserved. pdf 1.0.1 3-23-04 ontents Specifications........................... 2 Straight Plugs...................... 3 Right ngle
Stainless Steel SMA Connectors Product Catalog
Stainless Steel SMA Connectors Product Catalog Connectivity...for Stainless Steel SMA Connectors Connectivity...for Johnson Stainless Steel SMA Connectors meet or exceed the performance requirements of
RF CONNECTORS. Adam Technologies, Inc. ORDERING INFORMATION 1 01 D RoHS RFC SERIES INSULATOR A V A I L A B L E
INTRODUCTION: Adam Tech s RFC series RF connectors are a comprehensive assortment of Radio Frequency signal connectors in standard, miniature, sub-miniature, micro miniature and surface mount style. Included
Jul03 Rev C EC
Product Specification Coaxial BNC Solder Receptacle Connector 108-12079 10Jul03 Rev C EC 0990-0940-03 1. SCOPE 1.1. Content This specification covers the performance, tests and quality requirements for
ZDC RF Coax Connector Series 50 & 75 Ohm
CONTACTORS CONNECTORS WIRE & CABLE EMI/RFI FILTERS CIRCUIT BREAKERS HARNESSING & PROTECTION IDENTIFICATIO I/RFI FILTERS CIRCUIT BREAKERS HARNESSING & PROTECTION IDENTIFICATION & LABELING PCB & CABLE ASSEMBLIES
HDRFI Series Tensolite High-Performance Cable & Interconnect Systems. High Density RF Interconnect
HDRFI Series Tensolite High-Performance Cable & Interconnect Systems High Density RF Interconnect HDRFI is a patented Tensolite connection system that transfers high frequency signals through a unique
7RF Connectors. RF Connectors. Table of Contents
RF Connectors Table of Contents Military Qualified Introduction.........................................................7003 N Series Connectors MIL-C-3902 50 Ohm.....................................................
BNC 75 RF CONNECTORS. Simple steps to guide you in using this catalogue. Applications. Options. Ordering Codes BNC 75 RF CONNECTORS
BNC 75 RF CONNCTORS BNC 75 RF CONNCTORS Amphenol offers a complete range of highperformance BNC plugs for use in digital/ HD video applications. Amphenol s True 75 Ohm BNC connectors perform well up to
PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY (SERIES SMA (CABLED) - PLUG, PIN CONTACT, CLASS 2)
INCH-POUND MIL-PRF-39012/55G 6 February 2008 SUPERSEDING MIL-PRF-39012/55G 6 January 2006 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY (SERIES SMA (CABLED) -
Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height
Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.mm Mated Height U.FL Series Up to 6GHz Transmission Speed Mated Height Comparison (With E.FL series) 1.9(2.0Max) U.FL-LP(V)-00 2.(2.5Max)
SECTION 9 BNC/BNC 75 HDTV/BNC-TRX R141/R142/R266 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 9 BNC/BNC 75 HDTV/BNCTRX R141/R142/R266 SIMPLIFICATION IS OUR INNOVATON Visit www.radiall.com for more information Contents BNC Introduction... 94 to 95 Interfaces... 96 to 97 Characteristics...98
PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES TNC (CABLED), PIN CONTACT, RIGHT ANGLE, CLASS 2)
INCH-POUND MIL-PRF-39012/30H 15 March 2018 SUPERSEDING MIL-PRF-39012/30H w/amendment 3 15 April 2017 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES TNC
PERFORMANCE SPECIFICATION SHEET
INCH-POUND 5 October 2016 SUPERSEDING w/amendment 2 July 2016 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMA (CABLED) PIN CONTACT, RIGHT ANGLE, CLASS
CONNECTORS PRODUCTS RF CONNECTORS FIBER OPTIC PRODUCTS. Connector Products
FIBER OPTIC PRODUCTS RF CONNECTORS Netrade is a leading global supplier of a wide variety of standard and custom RF coaxial connectors, cable assemblies and unique solutions for today's cutting edge applications,
SECTION 10 BNC / BNC 75 HDTV / BNC-TRX R141 / R142 / R266
SECTION 10 10 BNC / BNC 75 HDTV / BNC-TRX R141 / R142 / R266 Contents Introduction... 10-4 to 10-5 Interfaces... 10-6 to 10-7 Characteristics... 10-8 to 10-11 Finder guide...10-12 to 10-13 COMPOSITE BNC
ULTIMATE SNAP-N-SEAL
ULTIMATE SNAP-N-SEAL F Series Compression Connectors Thomas & Betts introduces the Ultimate Snap-N-Seal Compression Connector, the newest addition to the Snap-N-Seal system. Look for the classic design
SERIES HPQN CONNECTORS
SERIES HPQN CONNECTORS 1 DESCRIPTION Patented in 2008 by Anoison Electronics, the HPQN is a quick locking version of the widely used type N connector. By replacing the threaded interface of the original
Amphenol Telecom Solutions
BNC 31 Series Bayonet Lock RF Connector System Materials Electrical Environmental Body/Finish /Nickel 50 ohm 75 ohm Temp. range -65 C thru 165 C Contact Frequency range 0-4GHz 0-10GHz Shock Consult Rep
INCH-POUND MIL-PRF-39012/29H w/amendment 3 25 January 2018 SUPERSEDING MIL-PRF-39012/29H w/amendment 2 21 November 2016
INCH-POUND MIL-PRF-39012/29H 25 January 2018 SUPERSEDING MIL-PRF-39012/29H w/amendment 2 21 November 2016 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO FREQUENCY, (SERIES
75 Ohm BNC Male Connector Crimp/Solder Attachment for PE-B159, 1855A, Mini 59
75 Ohm BNC Male Connector Crimp/Solder Attachment for PE-B159, 1855A, Mini 59 RF Connectors Technical Data Sheet PE44625 Configuration BNC Male Connector 75 Ohms Straight Body Geometry Features Max Operating
INCH-POUND MIL-PRF-39012/28H w/amendment 4 25 January 2018 SUPERSEDING MIL-PRF-39012/28H w/amendment 3 15 April 2017
INCH-POUND MIL-PRF-39012/28H 25 January 2018 SUPERSEDING MIL-PRF-39012/28H w/amendment 3 15 April 2017 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLES, ELECTRICAL, COAXIAL, RADIO FREQUENCY, (SERIES
75 Ohm N Male Connector Crimp/Solder Attachment for RG6
75 Ohm N Male Connector Crimp/Solder Attachment for RG6 RF Connectors Technical Data Sheet PE4508 Configuration N Male Connector 75 Ohms Straight Body Geometry Features Max Operating Frequency 15 GHz Good
QMA and QN connectors, patented products, become some real standard for the RF Telecommunications industry.
CONTENTS PAGE Introduction...4-5 Characteristics... 6 Plugs...7-9 Jacks...9- Receptacles...-4 Adapters...4-6 Protective cap... 6 Panel drilling... 7 Receptacles packaging... 8 Assembly instructions...9-30
PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES BNC (CABLED), PIN CONTACT, CLASS 2)
PERFORMANCE SPECIFICATION SHEET MIL-PRF-39012/16H 03 January 2017 SUPERSEDING MIL-PRF-39012/16H w/amendment 1 20 April 2009 CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES BNC (CABLED),
PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES BNC (CABLED), PIN CONTACT, CLASS 2)
INCH-POUND MIL-PRF-39012/16H 16 November 2006 SUPERSEDING MIL-PRF-39012/16G 26 September 1994 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES BNC (CABLED),
High Density BNC Connectors
High Density BNC Connectors Spacing HD-BNCTM High Density Cable 8 mm (.315 ) 64 interconnects in 2.5 x 2.5 Standard Cable 9.5 mm (.374 ) 36 interconnects in 2.5 x 2.5 Standard BNC 15.9 mm (.625 ) 16 interconnects
12G Broadcast connectors
12G Broadcast connectors Delivering 12G in a single punch www.coax-connectors.com Welcome to COAX 12G BNC Plug return loss COAX Connectors Ltd is a leading UK designer, manufacturer and supplier of high
D-COAX, Inc. D-COAX d086 Series Cable Pair. High Frequency, Skew Matched, Phase Stable Cable Pair (65 GHz)
D-COAX, Inc. D-COAX d086 Series Cable Pair High Frequency, Skew Matched, Phase Stable Cable Pair (65 GHz) D-COAX d086 Series Cable Pair consists of two skew matched (to 1ps) flexible cable assemblies with
8D with High Frequency Coaxial Contact
8D Series M Coaxial Contacts 8D with High Frequency Coaxial Contact robust and powerfull coaxial High Frequency transmission (M) now available in any size 8 SOURIU insert of D38999 Series III. Spring HF
Instrumental technique. BNC connector
Instrumental technique BNC connector Azhar 29/04/2017 What is it? The BNC (Bayonet Neill Concelman) connector is a miniature quick connect/disconnect electrical connector used for coaxial cable. Electrical
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 75 OHM AND 75 OHM HD COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT
Ultra-Small Surface Mount Coaxial Connectors mm Mated Height
All non- products have been discontinued, or will be discontinued soon. the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative. NEW Ultra-Small
Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height
Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.mm Mated Height U.FL Series Up to 6GHz Transmission Speed Mated Height Comparison (With E.FL series) 1.9(2.0Max) U.FL-LP(V)-00 2.(2.5Max)
Low Loss RG 402 Equivalent
421-671 Low Loss RG 402 Equivalent Section 10 Low Loss RG 402 Equivalent In applications that require the bendability of solid dielectric, but with the low loss that only a low density Teflon dielectric
BNCpro for 3G and Ultra-HD/4K
BNCpro for 3G and Ultra-HD/4K Table of Contents BNCpro Page Company Profile... 1 Product Description... 2 Technical Data... 3 Design Options... 5 Products Cable Plug... 6 Adaptor... 8 U-Link... 9 Terminator
INTER SERIES ADAPTERS INTRODUCTION & 2.4 MM, 2.9 MM INTER SERIES
INTRODUCTION & 2.4 MM, 2.9 MM INTER SERIES Inter series coaxial adapters are some of the more common components used in RF, microwave and wireless applications. OEM s and manufacturing and engineering
Part Number (used with PRO-CRIMPER Tool Frame ) for 50 Ohm BNC Dual Crimp MIL Type Connectors
Application Tooling Hand Tools CERTI-CRIMP Hand Tools are our top-of-the-line crimping tools featuring the original ratcheted crimp control. All tools are designed to exacting specifications, and manufactured
Lightweight SMT Miniature Coaxial Connectors 1.4 mm Mated Height
Lightweight SMT Miniature Coaxial Connectors 1.4 mm Mated Height N.FL Series Mated height comparison (With U.FL-LP(V) ) Features 1. Low profile Nominal mated height is 1.4 mm (Max. 1.5 mm) 2. Small size:
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 160 2010 Specification for Mini F Connector, Male, Pin Type NOTICE The Society of Cable Telecommunications Engineers
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE Specification for F Connector, Male, Pin Type
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 124 2011 Specification for F Connector, Male, Pin Type NOTICE The Society of Cable Telecommunications Engineers
BNC / BNC 75 HDTV / BNC-TRX series R141 / R142 / R266
10 BNC / BNC 75 HDTV / BNC-TRX series R141 / R142 / R266 CONTENTS Introduction... 10-4 to 10-5 Interfaces... 10-6 to 10-7 Characteristics... 10-8 to 10-11 Finder guide... 10-12 to 10-13 COMPOSITE BNC
Radiation-crosslinked,
ElectroLoss Filterline Product Facts n Suppresses EMI above 100 MHz n Light weight, small size n SPEC 55 insulation n 600 volt n -65 C up to 200 C [-85 F to 392 F] Available in: Americas Europe Asia Pacific
D-COAX, Inc. D-COAX Male-Female 1501 Series Cables and Cable Pairs. High Frequency, Skew Matched, Phase Stable Cable Pair (40 GHz)
D-COAX, Inc. D-COAX Male-Female Series Cables and Cable Pairs High Frequency, Skew Matched, Phase Stable Cable Pair ( GHz) D-COAX Series Cable Pair consists of two skew matched (to ps) flexible cable assemblies
BNC 75 Ohm RF-Connectors
BNC 75 Ohm RF-Connectors Table of Contents BNC 75 Ohm 1/2 Page Company Profile... 3 Product Description... 4 Technical Data... 5 Design Options... 6 Connectors Cable Plug... 8 Adaptor... 12 U-Link... 14
Cambridge Connectors A division of Cambridge Electronic Industries Ltd
TM Cambridge Connectors A division of Cambridge Electronic Industries Ltd Precision 75 ohm coaxial connectors for 3GHz digital broadcast and video applications including PCI Express and CoaXPress TM BNC
Ultra Small Surface Mount Coaxial Connectors 1.4mm Mated Height
All non- products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative.
Reverse polarity connectors
connectors Description According UL FCC (part 15.203) regulations, wireless radio equipment with removable antenna must not have a standardised interface. This to avoid the connection of antenna equipment
Ultra Small Surface Mount Coaxial Connectors 1.4mm Mated Height
NEW Ultra Small Surface Mount Coaxial Connectors 1.4mm Mated Height W.FL Series Further downsizing of FL series in response to the market needs. Occupied Mounting Area.0.0 Features 1. Mounting area of
SMP Connectors. Table of Contents PAGE. Introduction Specifications MountingHoles...7. Applications AssemblyTools...
SMP Connectors Table of Content Connectivity for Table of Contents PAGE Introduction...3-4 Specifications...5-8 MountingHoles...7 Applications...9-12 AssemblyTools...13 AssemblyInstructions...14-18 CompetitorCrossReference...19
0.3 mm Pitch, 1.5 mm Mated Height, Board- to-fine Coaxial Cable Connectors
All non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales
L SERIES amps (Type C) M) amps amps (Type D) B) amps (Type B) C)
L SERIES Hypertac modular connectors employ a do-ityourself system based on the building block principle. They offer a wide variety of combinations available in a single connector frame. Thus, the user
HOW TO USE THIS MANUAL
HOW TO USE THIS MANUAL This manual is organized first by Antenna Specialists Cable groups and second by the types of RFI connectors available for those groups. The connectors are divided into subgroups
Highlights: Cables & Adaptors. Stock Cable Assemblies Custom Cable Assemblies Multi-conductor Cables Patch Panels Connector Adaptors
Cables & Adaptors Highlights: Stock Cable Assemblies Custom Cable Assemblies Multi-conductor Cables Patch Panels Adaptors www.pcb.com 716-684-0001 PCB Piezotronics, Inc. Automotive Sensors Division Common
SECTION 8 QUICK-LOCK: QMA/WQMA/QN/QRE R123/R123W/R164/R324 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 8 QUICK-LOCK: QM/WQM/QN/QRE R123/R123W/R164/R324 SIMPLIFICTION IS OUR INNOVTON Visit www.radiall.com for more information Contents QM and WQM Introduction... 8-4 to 8-5 Characteristics... 8-6 to
Interface RF Connector with Switch
NEW Interface RF Connector with Switch MS-5C Series Overview Designed for end user applications requiring redirection of the transmission. Small size, lightweight and high reliability make it ideal for
Precision 75 ohm coaxial connectors for 3GHz digital broadcast and video applications including PCI Express and CoaXPress TM
Precision 75 ohm coaxial connectors for 3GHz digital broadcast and video applications including PCI Express and CoaXPress TM BNC Connectors 1.0/2.3 Connectors Mini BNC Connectors Edgecard Connectors Contacts
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 176 2011 Specification for 75 ohm 'MCX' Connector, Male & Female Interface NOTICE The Society of Cable Telecommunications
PL Series. Plastic Push Pull Interconnects
PL Series Plastic Push Pull Interconnects We Connect When it matters most For more than a century, ITT Cannon has developed innovative interconnect solutions for the world s most critical applications.
Interface Connectors for Miniature, Portable Terminal Devices
NEW Interface Connectors for Miniature, Portable Terminal Devices ST Series Strong locking mechanism Right Mating direction Left Top 9N max. Overview Developed as external input/output connectors for the
BTT rev. a Bob s TechTalk #8
BTT rev. a Bob s TechTalk #8 Bob s TechTalk #8 by Bob Eckweiler, AF6C Coaxial Connectors: (Part I of III) UHF and N Connectors and MMCX/MCX Series. There are many other connectors that are less common
Broadcast connector range.
Broadcast connector range. Featuring Single Channel 12G-SDI Connectors www.coax-connectors.com Contents. Section Page COAX in Broadcast 2 assembly service 3 Quality, performance and reliability by design
CONNECTORS. Simple steps to guide you in using this catalogue. Applications. Options. Ordering Codes BNC 75Ω RF CONNECTORS
NC 75Ω RF CONNCTORS NC 75Ω RF CONNCTORS Within the internationally standardised NC mating face dimensions, a perfect 75 ohm characteristic impedance cannot be realised. However, at frequencies up to 1000
Between Series Adapters
Between Series Adapters Between Series Adapters solve a variety of connection problems where connectors of different types ordinarily could not be mated together. Each adapter has a different type coupling
0.4 mm Pitch, Horizontal mating, Board- to-fine Coaxial Cable Connectors
0.4 mm Pitch, Horizontal mating, Board- to-fine Coaxial Cable Connectors DF49 Series Reliable connection 0.7±0.1 (Mated height) (0.5) Effective mating length Figure. 1 Mis-insertion Prevention Features
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Product Specifications Rating Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
Solderless RF Connectors
HF OPERATORS Solderless RF Connectors by John White VA7JW NSARC HF Operators 1 CenterPin Technology http://www.centerpin.com/ NSARC HF Operators 2 Connectors of Interest! 50 Ohm RF coax cable! PL-259 most
Sections 1. Application Equipment 2. Cable Preparation 3. Assembly 4. Termination Procedure 5. Inspection 6. Repair 7.
Page 1 of 6 Coaxial SolderSleeve Termination with Pre-Installed Wires or PCB Termination Body, B-044, B-043, B-041, B-040, B-020, B-021, B-046, D-148 Series Cable Type Typical RG Cable # -A- RG 178 RG
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
REQUIRED TOOLS. Wire cutters Razor blade Soldering iron Pliers 11/16 Wrench for Tube 18mm Wrench for Ring
S9122 PWS BNC MALE CABLE MOUNT COMPRESSION CONNECTOR S9022 PWS N TYPE MALE CABLE MOUNT COMPRESSION CONNECTOR S9322 PWS TNC MALE CABLE MOUNT COMPRESSION CONNECTOR The PWS S9122 is a BNC male cable mount
Small Circular Connector. JN1W / JN2W Series
COMPONENTS PRODUCT INFORMATION RoHS Compliant NEW Small Circular Connector / Series CONNECTOR MB-0178-5 December 2012 Angle Plug Cable Connecting Straight Plug Wall Mount Cable Connecting Waterproof Cap
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
APPLIANCES /// MTA, CST-100 II AND SL-156 CONNECTORS. CONNECTORS/ APPLIANCES MTA, CST-100 II and SL-156 Connectors
PPLINCES /// MT, CST-100 II ND SL-156 CONNECTORS CONNECTORS/ PPLINCES MT, CST-100 II and SL-156 Connectors Contents Introduction This catalog has been designed to assist you, our customer, identify products
HARTING Ethernet cabling cables and connectors, 4 wire
Industrial Cat. 5e Standard cable, 4-wire Type A for permanent installation or to build-up PROFINET system cables PVC X 8 wire X Cat. 5e X Cat. 6 Cat. 6 A Cat. 7 Cable structure Core structure Wire insulation
ENGINEERING COMMITTEE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 01 2015 Specification for F Port, Female, Outdoor NOTICE The Society of Cable Telecommunications Engineers (SCTE)
Cat.6 4 Pair UTP Cable
4 Pair UTP Cable Application: Voice Fast Ethernet(IEEE802.3u) VgAnyLAN(IEEE 802.12) Token Ring(IEEE 802.5) TPPMD(ANSI X3T9.5) BaseT Ethernet(IEEE 802.5) 155/622 Mbps 1.2/ 2.4 Gbps ATM 0BaseT Ethernet 550