Visionpro C Series Display Cube

Transcription

1 V1.4 VTRON http :// vtron.com All rights reserved

2 This manual is the copyright property of VTRON. Without the prior written consent of VTRON, no part of the text or graphics in this manual shall be copied or distributed to any party in any manner. This product may allow you to use third party software or upload/download works belonging to a third party, including articles, images, video, or software, but VTRON does not own or provide such works. Your use of the aforementioned works belonging to a third party means that you agree to use such works without infringing or breaching the rights of the third party, and VTRON does not assume any liability for your use thereof. VTRON and Visionpro are the global registered trademarks of VTRON Company. This manual is subject to change due to technical upgrades without prior notice. Note: Texts and graphics in this manual are for providing an introduction to the Visionpro series display cubes offered by VTRON only. Product configurations and functions will be in accordance with the purchase contracts signed by the customer. The functions and display interface of the product you order might differ from those in this manual. This is due to the difference in configuration between the one you purchased and the one introduced in this manual. Statement: Products as introduced in this manual are Class B products that may cause radio interference in domestic environment. Practical measures should be taken when necessary. Note: Images in this manual are for description and reference only. For actuality and details, please refer to the product you received. - i -

3 Safety Precautions! Before operating Visionpro series display cubes, please read and observe the following safety precautions thoroughly. Grounding (connected to earth) Ensure proper grounding(grounded as indicated in the figure) The product should be grounded properly. Otherwise, a series of problems will occur: serious system fault, system instability and unreliability, and even the paralysis to the whole system. Even worse, the safety of users cannot be ensured. Do not change the original design Any addition to or deletion from any mechanical part or electrical circuit in this product is prohibited. VTRON will not assume any liability resulting therefrom. Do not install unauthorized software The Visionpro series display cube is a dedicated device and must not be used for any other purpose. Consult VTRON or a designated agent for the installation of your own software. VTRON will not assume any liability resulting therefrom. - ii -

4 Be sure to disconnect the power supply before the following operations: A. Removal or reinstallation of any part of the product. B. Disconnection or reconnection of any electrical connector or other connector in this product. Keep the display cube away from corrosive chemical gas or agent Corrosive chemical gases or agents will damage the mechanical parts and electrical circuits of the product and directly affect its lifetime. Avoid cleaning the exterior or interior of the product with a highly volatile solvent, such as gasoline, paint thinner, acetone, etc. Keep the display cube away from flammable and explosive materials Product safety and personal safety cannot be ensured in an environment with flammable and explosive materials. Keep the display cube away from equipment with strong electromagnetic interference. - iii -

5 Dangerous voltage inside. May cause electric shock, burns, or death. No user serviceable parts inside. Only the dust screens and fuses are user serviceable. The maintenance personnel must be properly trained; otherwise, electric shock, UV radiation burns, contact burns, serious injury, or irreparable damage to the Visionpro series display cube may be caused, and your warranty will be invalidated. Only the dust screens and fuses are user serviceable The power must be disconnected before conducting such operations. All the maintenance tasks must be carried out by properly trained personnel. The projection unit uses a professional-grade ultra-bright LED light source. Do not replace the LED with another LED light source, or the system may be damaged. Do not shut down the cooling fan of the Visionpro series display cube or block the surrounding air circulation. - iv -

6 Dust in the air and hot air may cause the hardware of the Visionpro series display cube to short-circuit. Do not operate the cube in a dusty or high-temperature environment. A10 cm clearance must be maintained at the top of the vertical top layer of the Visionpro series display cube for the air circulation of the fan. Some screens are sensitive, and fingerprints on the screen will affect their optical performance. So the Visionpro series display cube must be protected against any touching or scratching. Disconnecting device of grid power This equipment uses a coupler or power connector as the disconnecting device. Make sure that the connector or coupler is easily accessible so that you can disconnect the grid power in an emergency. - v -

7 Content 1 DISPLAY CUBE OVERVIEW MAIN FEATURES APPEARANCE OF C SERIES DISPLAY CUBE MAIN COMPONENTS OF C SERIES DISPLAY CUBE TECHNICAL SPECIFICATIONS OF C SERIES DISPLAY CUBE DIMENSIONS OF C SERIES DISPLAY CUBE PROJECTOR OF C SERIES DISPLAY CUBE ENGINE OVERVIEW INTERFACE BOX OVERVIEW Appearance of the Interface Box Boards of VCL-3/VCL-3+ /VCL-3A Interface Box NETWORK ENVIRONMENT FOR THE VIDEO WALL SYSTEM INSTALLATION OF C SERIES DISPLAY CUBE VTRON DLP TM DIGITAL VIDEO WALL SYSTEM SYSTEM CONFIGURATION GROUNDING OF THE VIDEO WALL SYSTEM SYSTEM ON/OFF PRECAUTIONS DAILY MAINTENANCE TROUBLE SHOOTING CONTACT US vi -

8 1 Display Cube Overview C series display cube, launched by VTRON, is coming to the rescue in a video-wallneeded age! Redundant solid-state LED light source of 1500 ANSI lumens, full-cycle color & full- cycle brightness maintenance free as well as dual power module and other cutting-edge technologies help C series display cube to build an excellent wall. It is not the only but an ideal choice for all monitoring centers, command centers, and data management centers. Visionpro C series display cube has the following standard models, and you can have the product customized according to your actual needs. XGA Display Cube C-DX503 C-DX803 CF-DX675 C-DX507 C-DX603 C-DX505 C-DX805 C-DX607 CF-DX603 C-DX605 C-DX505D C-DX677 C-DX673 CF-DX605 C-DX605D C-DX807 CF-DX673 C-DX675 C-DX675D SXGA+ Display Cube C-SX503 CF-SX673 CF-SX605 C-SX505D C-SX507 C-SX603 C-SX803 C-SX675 C-SX605D C-SX607 CF-SX603 C-SX505 CF-SX675 C-SX675D C-SX677 C-SX673 C-SX605 C-SX805 C-SX805D C-SX P Display Cube C-PH603 CF-PH703 C-PH705 C-PH605D C-PH607 C-PH703 C-PH605 CF-PH705 C-PH705D C-PH

9 Note: C indicates the display cube uses C-type frame with rear access; CF indicates the display cube uses C-type frame with front access. DX indicates the display cube is in XGA resolution; SX indicates the display cube is in SXGA+ resolution; PH indicates the display cube is in 1080P resolution. The values of 50, 60, 67, 70, and 80 indicate the screen diagonal of the display cube. Value 3 indicates a 2 nd generation LED light source is used; Value 5 indicates a 3 rd generation LED light source is used; Value 7 indicates a 4 th generation LED light source is used. D indicates the display cube (3D display cube) supports 3D signal input and display

10 1.1 Main Features Ultra-long Lifetime & Environmentally friendly The change of light source is virtually unnecessary due to LED s long life time. It is environmentally friendly due to the absence of mercury, sodium, and other harmful substance. Full-cycle (Color & Brightness) Maintenance Free Technology Intelligent system self-diagnosis function brings automatic & immediate service recovery. High-quality Image Display Technology A LED light source of high ANSI lumens presents crisp, color-accurate, clear and vivid images. The image shows high uniformity, giving you delightful visual enjoyment. Strong Signal Acquisition& Signal Processing Capacity Signal acquisition (optional): DVI, VGA, CVBS, YPbPr, HDMI, 3G-SDI, DP signal input etc. are supported. Signal processing (optional): The C series display cube has strong signal processing capacity with its hot-swappable signal processing boards. Multiple Intelligent Protection for System Safety 1+1 redundant hot-swappable power supply, hot-swappable signal processing boards and modular design provide and maintain a healthy environment for the system running

11 1.2 Appearance of C Series Display Cube C Series Display Cube with Rear Access: 50, 60, 67,

12 C Series Display Cube with Front Access: The overall view The front view The rear view - 5 -

13 1.3 Main Components of C Series Display Cube The Visionpro C series display cube consists of the following parts. The relevant functions are described in the following table. Item Frame Screen Reflective Mirror Engine Projector Interface Box Power Module Six-axis Adjuster Function A part of the structure for positioning and installing the components of the integrated digital display cube. Displays the image received from reflective mirror. 1)Reflects the visual optical signal from the digital display component to the screen; 2)Reduces the thickness of the integrated digital cube. Converts the digital signal in TMDS format to an image signal to produce image information Converts computer signal into a digital signal in TMDS format and inputs the signal to the projector. It also provides a control port for receiving the control signal from the computer. It is embedded in the display cube frame and used to supply power to the engine and interface box. The mechanical position adjustment part of the projector, which is used to ensure the complete and correct output of the display image to the screen

14 1.4 Technical Specifications of C Series Display Cube The following technical specifications are only for display cubes with standard configuration. The detailed specifications may be different from the standard one due to the different optional components" you purchased. Standard Configuration Item Display Technology Resolution Light Source XGA Display Cube SXGA+ Display Cube 1080P Display Cube DLP technology (0.7 DMD, 14 LVDS) DLP technology (0.95 DMD, 12 LVDS) Redundant LED C series display cube with rear access : mm Gap(*) 1.0mm C series display cube with front access 2.5mm 3D display cube< 0.3 mm Control Mode Network control (RJ45): 10M/100M self-adaptive Ethernet port, Wireless remote control(optional) Type 1+1 redundant hot-swappable power Power Frequency Consumption 50/60Hz 145W - 350W Operating Environment Temperature 0-35 ( optimal temperature:23 ±5 ) Humidity 30-80% (no condensation) Certification CCC, CE, CB, ROHS Note: (*)The gap may differ according to screen type and operating environment (e.g., temperature, humidity). To ensure precision, the operating temperature and humidity is recommended to be within 24±2ºC and 50%~60% respectively

15 1.5 Dimensions of C Series Display Cube XGA&SXGA+ Display Cubes: XGA&SXGA+ Display Cubes Frame Type C-type with Rear Access C-type with Front Access Screen Diagonal(inches) W H Dimension(mm) D H

16 1080P Display Cube: 1080P Display Cube Frame Type C-type with Rear Access C-type with Front Access Screen Diagonal(inches) W Dimension(mm) H D H

17 2 Projector of C Series Display Cube The projector is very important as its performance will directly affect the visual quality of the cube and the wall. The projector of C series display cube, a digital display device composed of engine and interface box, is one of the most significant components of VTRON Video Wall. The product meets the national standards and technical codes and has obtained certificates of CCC, CE, CB, ROHS, etc. 2.1 Engine Overview Appearance 1: - 10-

18 Appearance 2: SN Name Filter DVI port Lens IR receiver/standby status LED indicator Fan Grounding screw Expansion port Power input port - 11-

19 2.2 Interface Box Overview VCl-3 interface box, VCL-3+ interface box, and VCL-3A interface box are available for C series display cube. The detailed interface configuration depends on the type of the cube Appearance of the Interface Box VCL-3 Interface Box: - 12-

20 VCL-3+ Interface Box: - 13-

21 VCL-3A Interface Box: VCL-3/VCL-3+/VCL-3A Interface Box: SN Name Pull-out power module of VCL-3 interface box 1 Dual AC power module of VCL-3+ interface box Dual power module of VCL-3A interface box Main control board (optional) Signal processing board (optional) DVI output port Power output port ( low voltage) Grounding screw - 14-

22 7 Power output port of the VCL-3 interface box Expansion port of the VCL-3A interface box 8 Power input port (low voltage) of VCL-3+ interface box Power output port(low voltage) of VCL-3A interface box Boards of VCL-3/VCL-3+ /VCL-3A Interface Box CP30SC Main Control Board(For VCL-3,VCL-3+ and VCL-3A interface boxes) 7-SEG LED indicator Desktop signal input port Ethernet port RS232 serial debug port Sync signal input port ON/OFF button Sync signal output port CP30SC Main Control Board - 15-

23 Specifications of CP30SC Main Control Board DVI Output Port DVI-D TMDS 25MHz-165MHz 35KHz-75KHz 50Hz/60Hz Resolution Control Mode I 2 C, SCL Frequency<100KHz Input/ Output Ports of CP30SC Main Control Board 1)Desktop Signal Input Port Digital Resolution DVI-I TMDS MHz 31KHz-75KHz 59Hz-61Hz 640x x1200 Analog Resolution Sync Signal Amplitude Sync Signal (green) Amplitude RGB Signal Amplitude DVI-I RGBHV, RGsB MHz 31KHz-75KHz 59Hz-61Hz ~ Vpp~5.5Vpp -0.5Vpp~-0.3Vpp 0.5Vpp~1.0Vpp 2)Sync Signal Input/Output Port BNC 2 Sync Signal Frequency Sync Signal Amplitude 50~60HZ 3.0V~~3.6Vpp - 16-

24 3)Ethernet Port Port Type RJ45 Standard 100M/10M Self-adaptive Ethernet Port CP30DSC Main Control Board(For VCL-3+ interface box only) 7-SEG LED indicator Power output port(low voltage) Master desktop signal input port Slave desktop signal input port Signal loop-out port Signal loop-in port Ethernet port Sync signal input port ON/OFF button Sync signal output port CP30DSC Main Control Board (3D Display Cube) Specifications of CP30DSC Main Control Board (3D Display Cube) DVI Output Port DVI-I TMDS 65MHz-330MHz 35KHz-135KHz 60Hz/120Hz Resolution / / Control Mode I 2 C,SCL Frequency<100KHz - 17-

25 Input/Output Ports of CP30DSC Main Control Board 1)Master Desktop Signal Input Port DVI-D Resolution TMDS MHz 31KHz-135KHz 24Hz/30Hz/60Hz/120Hz 640x x2160 2)Slave Desktop Signal Input Port DVI-D Resolution TMDS MHz 31KHz-135KHz 24Hz/30Hz/60Hz/120Hz 640x x2160 3)Signal Loop-in Port Resolution DisplayPort SERDES MHz 31KHz-135KHz 23Hz-121Hz 640x x2160 4)Signal Loop-out Port Resolution DisplayPort SERDES MHz 31KHz-135KHz 23Hz-121Hz 640x x

26 5)Sync Signal Input/Output Port BNC 2 Sync Signal Frequency Sync Signal Amplitude 60/120Hz 3.0V~~3.6Vpp 6)Ethernet Port Port Type RJ45 Standard 100M/10M Self-adaptive Ethernet Port - 19-

27 CP30SCIP Main Control Board (For VCL-3A interface box only) 7-SEG LED indicator Desktop signal input port 1 Desktop signal input Ethernet port/ IP signal input port 1 RS232 serial debug port Ethernet port/ IP signal input port 2 Sync signal input port ON/OFF button Sync signal output port CP30SCIP Main Control Board - 20-

28 Specifications of CP30SCIP Main Control Board DVI Output Port DVI-D TMDS 25MHz-165MHz 35KHz-75KHz 50Hz/60Hz Resolution Control Mode I 2 C, SCL Frequency<100KHz Input/ Output Ports of CP30SCIP Main Control Board 1)Desktop Signal Input Port Digital DVI-D TMDS MHz 31KHz-100KHz 23Hz-121Hz Resolution )Ethernet Port Port Type RJ45 2 Standard 100M/10M Self-adaptive Ethernet port 3)Sync Signal Input/Output Port BNC 2 Sync Signal Frequency Sync Signal Amplitude 50~60HZ 3.0V~~3.6Vpp - 21-

29 Note: (1)7-SEG LED Indicator The 7-SEG LED indicator is controlled through 3 I/O ports. Different display content indicates different system status. Details are shown in the following table. Content System Status Content System Status 0 Interface box powered up, loading program started 0. Error loading program 1 Application initialization 1. Error during application initialization 2 IP configuration (static IP or dynamic IP) 3 Interface box started, main control board powered up 4 Downloading FPGA program of main control board 5 Configuration of FPGA parameters of main control board 2. IP configuration failure 3. Error starting interface 4. Error downloading FPGA program of main control board 5. Error configuring FPGA parameters of main control board 6 Engine powered on 6. Error starting engine 7 Waiting for the completion of engine initialization 7. Engine initialization error 8 Configuring engine 8. Engine configuration failure 9 Engine detection 9. Display failure E E. There are two situations in which E is displayed: 1. An error is detected, but this error is not serious enough to trigger the protection mode. For the moment, this only includes the DVI disconnection error. 2. It is displayed during the 1-minute waiting time before entering the protection mode.. Flashing: engine is shutting down. Standby Normal operation - 22-

30 Note: A. The 7-SEG LED indicator displays a random value in the first several seconds of power-up because it takes several seconds from power-up to the initialization of the 7-SEG LED indicator. B. If the alarm forces the engine to enter the protection mode, an alarm message will be sent to remind the user of the failure, and then the engine will enter the protection mode and shut down in 1 minute. (2)RS232 Serial Debug Port RS232 serial debug port is used to debug during development or in the event of an RJ-45 failure. It is connected to the engine through D-Sub 9 Pins Male Connector. Details are shown as below. Pin No. Input/Output Signal 1 N.C 2 Input RD(Receive Data) 3 Output SD(Send Data) 4 N.C 5 SG(Signal Ground) 6 N.C 7 N.C 8 N.C 9 N.C (3)ON/OFF Button When the projector is powered up and in standby mode, press and hold this button for 2 to 3 seconds to start the projector. When the projector is in its normal operating mode, press and holds this button for 2 to 3 seconds to shut down the projector. The fan will stop in 1 to 2 seconds after the projector shuts down

31 E-CP30VR02 Signal Processing Board(Optional) VIDEO signal input port S_VIDEO signal input port HDMI signal input port Signal loop-out port Signal loop-in port DRGB signal input port ARGB signal input port E- CP30VR02 Signal Processing Board Specifications of E-CP30VR02 Signal Processing Board VIDEO Signal Input Port CVBS Signal System Signal Amplitude BNCx1 CVBS PAL, NTSC, SECAM 0.5 Vpp~2.0Vpp - 24-

32 S_VIDEO Signal Input Port YPrPb Resolution Signal Amplitude YC Signal System Signal Amplitude S_VIDEO YPrPb 480i, 480p, 576i, 576P, 720P, 1080i,1080p 0.5Vpp~1.0Vpp S_VIDEO YC PAL, NTSC, SECAM 0.5 Vpp~2.0Vpp HDMI Signal Input Port Digital Resolution HDMI TMDS MHz 31KHz-100KHz 24~60Hz 480i, 480p, 576i, 576P, 720P, 1080i,1080p RGB Signal Input Port Digital DVI-D TMDS MHz 31KHz-100KHz 23Hz-121Hz Resolution ~ Analog BNCx5 RGBHV, RGsB MHz 31KHz-100KHz 23Hz-121Hz Resolution 640x480~ ( including ) - 25-

33 Sync Signal Amplitude Sync Signal (green) Amplitude RGB Signal Amplitude 2.5Vpp~5.5Vpp -0.5Vpp~-0.3Vpp 0.5Vpp~1.0Vpp Signal Loop-in/Loop-out Port Loop-in Resolution Loop-out Resolution DVI-D TMDS MHz 31KHz-100KHz 23Hz-121Hz 640x480~ DVI-D TMDS 27~165MHz 31KHz-100KHz 23Hz~121Hz 640x480~

34 E-CP30VR04II Signal Processing Board VIDEO signal input port S_VIDEO signal input port Signal loop1-out port HDMI signal input port Signal loop1-in port Signal loop2-out port Signal loop2-in port DRGB signal input port ARGB signal input port E-CP30VR04II Signal Processing Board Specifications of E-CP30VR04II Signal Processing Board VIDEO Signal Input Port CVBS Signal System Signal Amplitude BNCx1 CVBS PAL, NTSC, SECAM 0.5 Vpp~2.0Vpp - 27-

35 S_VIDEO Signal Input Port YPrPb Resolution Signal Amplitude S_VIDEO YPrPb 480i, 480p, 576i, 576P, 720P, 1080i,1080p 0.5Vpp~1.0Vpp YC Signal System Signal Amplitude S_VIDEO YC PAL, NTSC, SECAM 0.5 Vpp~2.0Vpp HDMI Signal Input Port Digital Resolution HDMI TMDS MHz 31KHz-100KHz 24~60Hz 480i, 480p, 576i, 576P, 720P, 1080i,1080p RGB Signal Input Port Digital DVI-D TMDS MHz 31KHz-100KHz 23Hz-121Hz Resolution ~ Analog BNCx5 RGBHV RGsB MHz 31KHz-100KHz 23Hz-121Hz Resolution 640x480~ ( including ) Sync Signal Amplitude Sync Signal (green) Amplitude RGB Signal Amplitude 2.5Vpp~5.5Vpp -0.5Vpp~-0.3Vpp 0.5Vpp~1.0Vpp - 28-

36 Signal Loop-in/Loop-out Port Signal Loop1-in Port DisplayPort SERDES 27 MHz ~330MHz 31KHz~135KHz 23Hz~121Hz Resolution ~ Signal Loop1-out Port DisplayPort SERDES 27 MHz ~330MHz 31KHz~135KHz 23Hz~121Hz Resolution ~ Signal Loop2-in Port DisplayPort TMDS 27 MHz ~165MHz 31KHz~135KHz 23Hz~121Hz Resolution ~ Signal Loop2-out Port DisplayPort TMDS 27 MHz ~165MHz 31KHz~135KHz 23Hz~121Hz Resolution ~

37 E-CP30SKD04 Signal Processing Board (Optional) SDI1 signal input port SDI2 signal input port HDMI signal input port Signal loop1-out port DP signal input port Signal loop1-in port Signal loop2-out port Signal loop2-in port DRGB1 signal input port DRGB2 signal input port E-CP30SKD04 Signal Processing Board - 30-

38 Specifications of E-CP30SKD04 Signal Processing Board SDI Signal Input Port SDI Resolution Signal Amplitude BNCx2 SDI 480i, 576i., 720p, 1080i, 1080p 23.98Hz~60Hz 0.8Vpp HDMI Signal Input Port Digital HDMI TMDS 25~300MHz 31KHz-100KHz 24~60Hz Resolution ~ DP Signal Input Port Digital DisplayPort micro-packet 25~300MHz 31KHz-100KHz 24Hz~60Hz Resolution ~ RGB Signal Input Port Digital DVI-D 2 TMDS 27~330MHz 31KHz~100KHz 23Hz-121Hz Resolution ~

39 Signal Loop-in/Loop-out Port Signal Loop1-in Port DisplayPort SERDES 27~330MHz 31KHz~100KHz 23Hz-121Hz Resolution ~ Signal Loop1-out Port DisplayPort SERDES 27~330MHz 31KHz~100KHz 23Hz~121Hz Resolution ~ Signal Loop2-in Port DisplayPort TMDS MHz 31KHz~135KHz 23Hz-121Hz Resolution ~ Signal Loop2-out Port DisplayPort TMDS 27~165MHz 31KHz~135KHz 23Hz~121Hz Resolution ~ Note: (1)SDI1 signal input port and SDI2 signal input port are backups for each other. (2)DRGB1 signal input port and DRGB2 signal port are backups for each other

40 E-CP30SDI02 Signal Processing Board ( Optional) SDI1 signal input port SDI2 signal input port HDMI signal input port Signal loop2 port Signal loop1 port Genlock sync signal input port Vertical sync signal output port CP30SDI02 Signal Processing Board Specifications of E-CP30SDI02 Signal Processing Board SDI Signal Input Port SDI Resolution Signal Amplitude BNCx2 SDI 480i, 576i, 720p, 1080i, 1080p 23.98Hz~60Hz 0.8Vpp - 33-

41 Genlock Sync Signal Input Port/ Vertical Sync Signal Output Port Genlock Sync Signal Frequency Sync Signal Input Amplitude Sync Signal Input Amplitude(Analog black burst/hd tri-level sync) Sync Signal Output Amplitude BNC 2 50~60Hz 3.0V~~5.5Vpp 0.3Vpp~1.2Vpp 3.0V~~3.6Vpp HDMI Signal Input Port Digital Resolution HDMI TMDS 27MHz-165MHz 31KHz-100KHz 50~60Hz 480i, 480p, 576i, 576P, 720P, 1080i,1080p Signal Loop Port Signal Loop1-in Port Dual-DVI TMDS MHz 31KHz-100KHz 23Hz-121Hz Resolution ~ Signal Loop1-out Port Dual-DVI TMDS 27~165MHz 31KHz~100KHz 23Hz~121Hz Resolution ~

42 Signal Loop2-in Port Dual-DVI TMDS MHz 31KHz-100KHz 23Hz-121Hz Resolution ~ Signal Loop2-out Port Dual-DVI TMDS 27~165MHz 31KHz~100KHz 23Hz~121Hz Resolution ~ Note: (1) Two channels of SDI signal back up each other. (2) Vertical sync signal output port of E-CP30SDI02 signal processing board put out the signal generated from Genlock sync signal to the sync signal input port of main control board. Once one of the display cubes acquired the signal, its sync signal output port will have loop-through to sync signal input port of the other cube till all cubes of the wall are looped. Schematic diagram for synchronization looping is shown in the following figure: - 35-

43 - 36-

44 3Network Environment for the Video Wall System The interactions of cubes, processors, network switches, and VWAS server are based on network communication and they are configured by certified professionals. If you need assistance, please consult VTRON professional services. Warning: NO connection to the external network! Details are shown in the following figure: - 37-

45 4 Installation of C Series Display Cube 4.1 VTRON DLP TM Digital Video Wall System Linear Video Wall A linear video wall can be lined up and stacked by M N display cubes and N pedestals. A 2 2 linear video wall is shown as below

46 Curved Video Wall A curved video wall can be lined up and stacked by M N display cubes and N pedestals. A 3 5 curved video wall is shown as below. Note: 3D display cubes do not allow setting up a curved video wall temporarily

47 4.2 System Configuration A basic video wall system is composed of display cubes, one or more multi-screen processors, pedestals and other devices. Configuration for a 3 5 video wall system is shown in the following figure

48 4.3 Grounding of the Video Wall System The engine and interface box of every display cube must be connected to the grounding wire. Detailed grounding for a 2 2 video wall system is shown as below. Warning The system must be installed by VTRON or its agent. You must not move or change the grounding, otherwise personal or equipment safety may be endangered

49 5 System ON/OFF Before starting the system: 1. Please make sure all cables are reliably connected and securely fastened; 2. Please make sure the system is properly grounded; 3. Please make sure the power switch of the display cube is in ON status; 4. Please make sure the lens cover is removed. Startup Steps: 1. Turn on the power switch of the signal system and input signal; 2. Turn on the power supply of the multi-screen processor; 3. Turn on the power supply of the PC running VWAS; 4. When the multi-screen processor completes its self-detection, start the control system software on the PC and start the display cubes with the control system software. Note: 1. Turn on the display cube after it has been powered up for one minute; 2. It will take some time for the display cube to display any content after startup. Do not repeatedly press the POWER button in the control software. Shutdown Steps: 1. Shut down the multi-screen processor and turn off its power switch when the prompt for safe shutdown appears. 2. Shut down the display cubes with control software on PC and then shut down the PC. 3. Turn off the power switch of interface box when the fan of projector stops. Note: Any forced power-off may cause damage to the system. Warning The system commissioning and parameter adjustment can only be performed by trained and qualified professionals

50 6 Precautions Please read the following carefully and strictly comply with the following safety precautions before and during daily maintenance and troubleshooting. This is very important for protecting your safety and your equipment. 1. Before disconnecting or connecting any electrical devices, please make sure the system has been shut down and the system power cable has been unplugged. 2. Please make sure all system devices are properly grounded. 3. Do not open the top cover of the display cube. 4. Do not spray any chemical or other liquid on or near the digital video wall system. 5. Do not place any wet or heating objects near the system devices. 6. Do not make any changes or add any components to the original electrical and mechanical design of the display cube. 7. Do not place anything in or above the ventilation hole and ventilation slot. 8. Please strictly comply with the required startup/shutdown steps of the Visionpro series display cube. 9. Please put the display cube in a place with good ventilation. 10. The air outlet of the central air conditioner must be at least 1 m away from the front projection of the video wall system and the air outlet of a cabinet air conditioner must not blow directly to the video wall system. Warning The VTRON digital display cube is a specialized display and control system. If you need to install additional software, be sure to consult VTRON or its agent first

51 7 Daily Maintenance 1. Please use dedicated cleaning tools to clean the screen surface of the display cube; 2. Do not touch the screen surface with your hands; 3. Please use dedicated cleaning tools to clean lens; 4. Do not replace the LED light source for yourself; 5. Please keep a clean, dust-free, and well- ventilated environment for the display system. 6. Please regularly check the connection of all cables. 7. Please turn on and run the system for 1 to 2 hours each week, if the system is not frequently used. In damp seasons, once or more per day is recommended. Light Source Note: During projector operation, avoid looking directly at the lens. It is normal for the brightness of the light source to be reduced when it is close to the end of its lifetime. Fan Do not place any objects in or on the ventilation hole in the projector to ensure proper ventilation and heat dissipation. Grounding Please ensure that the grounding wires of both the display system and the power supply are at the same level and that they are connected to the ground in order to prevent lightning and static damage. Operating Environment Please keep a clean, dust-free and well-ventilated environment for the display system. Cable Connections Please use cables provided by VTRON and regularly check the connection of all cables

52 Warning The replacement of the light source under special circumstances must be performed by professionals from VTRON. 8 Trouble Shooting Normal Startup Process for the Projector 1) Connect the power supply and turn on the power switch, and then the projector will automatically update the corresponding information in the FLASH memory. 2) The projector can be started when the standby status LED is on. Afterward, the fan will start and the LED light source will turn on. Troubleshooting 1. No response when power is turned on: a) Check to see if the power supply is operating normally with a multimeter. b) Check to see if the connecting cable between the interface and engine is firmly connected. c) Check to see if the power switch is turned on. 2. No image is displayed after device is turned on: (1) No warning signal is displayed a) Check to see if the signal cables are connected correctly. b) Check to see if the signal output of the signal source is normal. (2) Warning signal is displayed Please consult professional service personnel

53 9 Contact Us About after sales service matters please contact after sales department of VTRON GROUP CO.,LTD. VTRON GROUP CO.,LTD. No. 233 Kezhu Road, Guangzhou Hi-Tech Industrial Development Zone (Guangzhou Science City), Guangzhou , China Tel: Fax: VTRON GROUP CO.,LTD. (Hong Kong) Unit , 16/F, Tower 1, 193 Prince Edward Road West, Grand Century Place Mongkok, Kowloon Hong Kong Tel: Fax: VTRON Hong Kong Technical Support Centre Unit 1225, 12/F, Corporation Park,11 On Lai Street, Shatin, New Territories, Hong Kong Tel: Fax: VTRON GROUP CO.,LTD. (Malaysia Rep Office) Unit 29-6 Block E1, Dataran Prima Business Centre, Jalan PJU 1/42, Petaling Jaya 47301, Selangor Darul Ehsan, Malaysia. Tel: Fax: