Enterprise Networks. Comms Room and Backbone. in DETAIL

Transcription

1 Enterprise Networks Comms Room and Backbone in DETAIL 31

2 Patch Panels 33

3 CAT 6 CL 16 WAY PATCH PANEL 19 1U Category 6 performance patch panel. Jacks are fitted. Integral cable management and reusable label holders. Supplied complete with fixings. CL CL 16 way shielded patch panel PATCH PANELS CL 16 way unshielded panel /1/100/16 CL 16 way shielded panel /1/150/16 CAT 6 KM8 & K8 (HK) 19" 1U Category 6 performance patch panel. Supplied with modular keystone jacks and fixings. Integral cable management and covered labelling field. Outrigger and patch panel termination rail should be used when installing this product - page 52 HK K8 (HK) 16 way unshielded patch panel KM8 (HK) 16 way unshielded panel /1/440/16 KM8 (HK) 16 way shielded panel /1/441/16 K8 (HK) 16 way unshielded panel /1/703/16 CAT 6 KM8 & K8 (HK) High density 19" 1U Category 6 performance patch panel. Supplied with modular keystone jacks and fixings. Integral cable management and covered labelling field. Outrigger and patch panel termination rail should be used when installing this product - page 52 HK K8 (HK) 24 way unshielded patch panel KM8 (HK) 24 way unshielded panel /1/440/24 KM8 (HK) 24 way shielded panel /1/441/24 K8 (HK) 24 way unshielded panel /1/703/24 34

4 24 WAY MODULAR HK PATCH PANEL High density 19" 1U unshielded or shielded patch panel. Supplied with modular keystone jacks and fixings. Integral cable management and covered labelling field. Outrigger and patch panel termination rail should be used when installing this product - page 52 HK 24 way modular HK unshielded patch panel 24 port 1U 568A/B unshielded panel /1/402/24 24 port 1U 568A/B shielded panel /1/412/24 24 WAY PCB PATCH PANEL High density 19" 1U PCB patch panel complete with rear cover, instruction sheet and fixing kit. Integral cable management. Colour coded label strips. PATCH PANELS PCB 24 way unshielded PCB patch panel 24 way 1U unshielded panel /1/607/24 24 way 1U shielded panel /1/619/24 48 WAY PCB PATCH PANEL High density U PCB patch panel complete with rear cover, instruction sheet and fixing kit. Integral cable management. Colour coded label strips. PCB 48 way shielded PCB patch panel 48 way 1.5U unshielded panel /1/630/00 48 way 1.5U shielded panel /1/632/00 35

5 16 WAY CL PATCH PANEL 19" 1U 16 way shielded patch panel. Uses the angled shield connector with overall metal lid (stainless finish). Jacks are fitted. Integral cable management. Integral reusable label holders (colour coded labels also available). Supplied complete with fixings. CL 16 way CL patch panel PATCH PANELS 16 way 1U shielded panel /1/651/01 16 WAY LN PATCH PANEL 19" 1U 16 way unshielded patch panels. Jacks are fitted. Integral cable management. Integral reusable label holders. Supplied complete with fixings. LN 16 way LN patch panel 16 way 1U unshielded panel /1/710/16 TELCO PATCH PANEL 19" 1U 24 way patch panel wired for 10BaseT applications. Features 24 RJ45 ports at front and two 50 way Telco sockets on the rear of the PCB. Colour coded label strips and fixings supplied. Range of Telco leads also available on request. PCB Patch panel 24 way Telco UTP Description Dimensions Pack Qty KRONE Product No Telco panel 44.4(h)x482(w)x128(d)mm /1/624/24 THROUGH COUPLER PATCH PANEL 19" 1U 24 way patch panel, featuring RJ45 jacks on both front and rear. Colour coded label strips and fixings available. PCB Patch panel 24 way through coupler UTP Description Dimensions Pack Qty KRONE Product No Through coupler panel 44.4(h)x482(w)x128(d)mm /1/623/24 36

6 ISDN 24 WAY S-BUS PATCH PANEL Supports up to 3 Basic Rate ISDN S-Buses, up to 8 ISDN devices on each Bus, thus dispensing with the need for dedicated ISDN outlets or ISDN terminated adaptors. Allows the ISDN service to be distributed to several outlets by patching over a structured cabling system. RJ45 presentation. Dimensions as per 24 way PCB patch panels. ISDN ISDN S-Bus panel ISDN panel /1/714/24 24 WAY PCB PATCH PANEL h w 48 WAY PCB PATCH PANEL 44.4mm (h) x 482mm (w) x 175mm (d) PATCH PANELS h w 66.6mm (h) x 482mm (w) x 175mm (d) 16 WAY CL PATCH PANEL h 24 WAY MODULAR HK PATCH PANEL w 44.4mm (h) x 482mm (w) x 101.2mm (d) 33 d 44 h 483 w 44.4mm (h) x 483mm (w) x 33mm (d) 16 WAY LN PATCH PANEL h d 44mm (h) x 482mm (w) x 101mm (d) w 37

7 ...

8 Data Modules 39

9 DATA MODULES HIGHBAND ULTIMATE MODULE Highest performance cross-connect system offering the user the ultimate in future-proofing, far exceeding the requirements for Category 6. Very easy to install and maintain. Terminates 2 four pair UTP cables. Recommended use is to hard wire the entire system and use patchcords (which will over-ride the installed connections) for all the adds, moves and changes. Modules also allow for centre port test access for individual data circuits, minimising any network downtime. Identical dimensions to 10 pair LSA-PLUS Series 2 module, allowing normal mounting hardware to be used. Dedicated frames also available - see frames, racks and cabinets section - page 47 Highband Ultimate module complete with jumper rings /5/060/08 HIGHBAND 8 PAIR MODULE High performance cross connection system enabling the user to both jumper and patch on the same module. Very easy to install and maintain. Terminates 2 four pair UTP cables. Recommended use is to hard wire the entire system and use patchcords (which will over-ride the installed connections) for all the adds, moves and changes. Modules also allow for centre port test access for individual data circuits, minimising any network downtime. Identical dimensions to 10 pair LSA-PLUS Series 2 modules, allowing normal mounting hardware to be used. Dedicated frames also available - see frames, racks and cabinets section - page 47 HIGH BAND HIGH BAND Highband Ultimate (Cat 6) module Highband 8 (Cat 5e) module Highband 8 pair module complete with jumper rings /5/060/00 Highband 8 pair module without jumper rings /5/060/20 HIGHBAND 16 PAIR MODULE High performance cross connection system for use where high density patching is required. Very easy to install and maintain. Terminates 4 four pair UTP cables. Identical dimensions to 10 pair LSA-PLUS Series 2 module, allowing normal mounting hardware to be used. Dedicated frames also available - see frames, racks and cabinets section - page 47 HIGH BAND Highband 16 (Cat 5e) module Highband 16 pair patching module complete with jumper rings /5/080/00 Highband 16 pair patching module without jumper rings /5/080/20 40

10 HIGHBAND ULTIMATE TRUEPATCH CORDS TruePatch C6T Highband patchcords. Essential component in TrueNet C6T system where Highband Ultimate modules are used. Wiring is standard 568B. HIGH BAND 0.5m Highband Ultimate TruePatch cord TruePatch C6T Highband Ultimate module to Highband Ultimate module 10 TP6TH-XXZZ TruePatch C6T Highband Ultimate module to RJ45 10 TP6TB-XXZZ Where XX: GY=Grey, BL=Blue, RD=Red, GN=Green Where ZZ: 04=1m, 07=2m, 10=3m, 15=5m HIGHBAND TRUEPATCH CORDS TruePatch C5eT Highband patchcords. Essential component in TrueNet C5eT system where Highband 8 pair modules are used. Wiring is standard 568B. DATA MODULES HIGH BAND 0.5m Highband TruePatch cord TruePatch C5eT Highband module to Highband module 10 TP5ETR-XXZZ TruePatch C5eT Highband module to RJ45 10 TP5ETH-XXZZ Where XX: GY=Grey, BL=Blue, RD=Red, GN=Green Where ZZ: 04=1m, 07=2m, 10=3m, 15=5m HIGHBAND PATCHCORDS Available in 0.5, 1, 2, 3 and 5m lengths. Suitable for use with Highband Ultimate 8 pair, Highband 8 pair and 16 pair modules. Used to provide a patched connection or to over-ride a jumpered connection. All patchcords are provided with a release latch to ensure that circuits cannot be accidentally disconnected. HIGH BAND 0.5m Highband Ultimate, 4 pair patchcord Highband 8, 4 pair patchcord /2/051/** Highband 16, 4 pair patchcord /2/050/** Highband 8/16 1 or 2 pair patchcord /2/048/** Highband 8/16 voice patchcord /2/059/** ** 01 = 0.5m, 11 = 1m, 21 = 2m, 31 = 3m, 51 = 5m Highband 8, 4 pair patchcord to RJ /2/058/** Highband 16, 4 pair patchcord to RJ /2/057/** 568A** 01 = 0.5m, 11 = 1m, 21 = 2m, 31 = 3m 568B ** 02 = 0.5m, 12 = 1m, 22 = 2m, 32 = 3m 41

11 ACCESSORIES Accessories include a label holder for circuit identification, and disconnection plugs for rapid disconnection of installed circuits. HIGH BAND Highband Ultimate, 1 pair test plug set DATA MODULES 1 pair test plug set /2/055/00 Label holder /2/096/00 1 pair disconnection plug /2/097/00 42

12 Patchcords 43

13 CATEGORY 6 TRUENET TM PATCH CORDS TrueNet TM C6T Patchcords are available in both RJ45 and in Highband Ultimate module variants. Wiring is standard 568B. C6T TrueNet TM RJ45 patchcord PATCHCORDS A Cable Type LSZH UTP PVC UTP B Cable Colour White Blue Red Yellow Green Orange Purple Grey C Length No: No: No: Follow the format below to order the patchcord you require: m 2.0m 3.0m 5.0m The part number digits relate to the different characteristics of the patchcord, ie: 6830/2/AB/C For example, if you wanted to order a PVC UTP purple 3m patchcord, the number would be: 6830/2/036/10 For shielded patchcords please contact KRONE SALES. CATEGORY 6 HIGHBAND PATCH CORDS TrueNet TM C6T Highband patchcords are essential components in systems where Highband Ultimate modules are used. Wiring is standard 568B. C6T TrueNet TM Highband Ultimate patchcord TrueNet TM C6T cord - RJ45 to Highband Ultimate module 1 TP6TB - XXZZ TrueNet TM C6T cord - Highband Ultimate module to Highband Ultimate module 1 TP6TH - XXZZ Where XX: GL=Grey, BL=Blue, RD=Red, GN=Green Where ZZ: 04=1m 07=2m 10=3m 15=5m 44 KRONE SALES

14 CATEGORY 5E TRUENET TM PATCH CORDS C5eT TrueNet TM Patchcords are available in both RJ45 and in Highband module variants. Wiring is standard 568B. C5eT TrueNet TM RJ45 patchcord TrueNet TM C5eT cord - RJ45 to RJ45 1 TP5ETA-XXZZ TrueNet TM C5eT cord - RJ45 to Highband module 1 TP5ETB-XXZZ TrueNet TM C5eT cord - Highband module to Highband module 1 TP5ETH-XXZZ Where XX: GL=Grey, BL=Blue, RD=Red, GN=Green Where ZZ: 04=1m 07=2m 10=3m 15=5m CATEGORY 6 PATCHCORDS Range of Category 6 patchcords available in various cable types, colours and lengths. PATCHCORDS A Cable Type B Cable Colour Category 6 RJ45 patchcord C Length No: No: No: LSZH UTP PVC UTP Follow the format below to order the patchcord you require: White Blue Red Yellow Green Orange Purple Grey m 2.0m 3.0m 5.0m The part number digits relate to the different characteristics of the patchcord, ie: 6830/2/AB/C For example, if you wanted to order a LSZH UTP blue 1m patchcord, the number would be: 6830/2/001/04 KRONE SALES

15 CATEGORY 5E PATCHCORDS Range of Category 5e patchcords available in various cable types, colours and lengths. Category 5e RJ45 patchcord PATCHCORDS A B C Cable and Boot Type Colour Length No: No: No: No: 5718/1/ /1/ /1/ /1/ /1/ 30 Follow the format below to order the patchcord you require: UTP PVC Unbooted UTP PVC Booted UTP LSZH Unbooted (Orange only) STP PVC Unbooted STP LSZH Unbooted (Orange only) Grey Red Green Blue Yellow White Orange (LSZH only) The part number digits relate to the different characteristics of the patchcord, ie: 5718/1/AB/C For example, if you wanted to order a UTP PVC Booted Green 2m patchcord, the number would be: 5718/1/043/ m 0.5m 1.0m 1.5m 2.0m 2.5m 3.0m 3.5m 4.0m 4.5m 5.0m HIGHBAND PATCHCORDS Available in 0.5, 1, 2, 3 and 5m lengths. Suitable for use with Highband Ultimate 8 pair, Highband 8 pair and 16 pair modules. Used to provide a patched connection or to over-ride a jumpered connection. All patchcords are provided with a release latch to ensure that circuits cannot be accidentally disconnected. 0.5m Highband Ultimate, 4 pair patchcord Highband 8, 4 pair patchcord /2/051/** Highband 16, 4 pair patchcord /2/050/** Highband 8/16 1 or 2 pair patchcord /2/048/** Highband 8/16 voice patchcord /2/059/** ** 01 = 0.5m, 11 = 1m, 21 = 2m, 31 = 3m, 51 = 5m Highband 8, 4 pair patchcord to RJ /2/058/** Highband 16, 4 pair patchcord to RJ /2/057/** 568A** 01 = 05m, 11 = 1m, 21 = 2m, 31 = 3m, 51 = 5m 568B ** 02 = 0.5m, 12 = 1m, 22 = 2m, 32 = 3m 52 = 5m 46

16 Frames, Racks & Cabinets 47

17 ADVANCED PATCHING FRAME (APF) II 19" modular open frame or cabinet, capable of accommodating up to 42 1U patch panels and/or active equipment. Supplied flat packed in 4 basic easily assembled parts, with 10 cable management arms. Frames fit back-to-back, side-to-side or at right angles. Cabinet versions also available, supplied with side panels and either glass or steel lockable doors. Suitable for both copper and fibre applications. Copper patch panels - page 33, Fibre patch panels - page 55, 61, Accessories - page 51 Advanced patching frame (APF) II FRAMES, RACKS AND CABINETS Description Pack Qty Weight KRONE Product No Advanced patching frame 42U 1 68kg 6420/1/500/00 Advanced patching frame 42U with glass doors 1 95kg 6420/1/501/00 Advanced patching frame 42U with steel doors 1 92kg 6420/1/501/01 Advanced patching frame 42U with glass doors and side panels 1 120kg 6420/1/503/00 Advanced patching frame 42U with steel doors and side panels 1 117kg 6420/1/503/01 APF door set - glass 1 27kg 6420/1/510/00 APF door set - steel 1 24kg 6420/1/511/00 Side panels 2 25kg 6420/1/504/00 Side panel extension kit /1/505/00 APF cable management arms /1/103/01 APF cable management arm extensions /1/516/00 Back-to-back kit /1/506/00 Side-to-side kit /1/507/00 Rear panel /1/508/00 Active equipment tray /1/509/00 Heavy duty active equipment tray /1/509/01 APF computer floor mounting 100mm /1/513/00 APF computer floor mounting 200mm /1/514/00 Power rail /1/512/00 Patch panel earth straps /1/056/00 ADVANCED PATCHING FRAME All measurements in millimetres Advanced patching frame (APF) II with glass doors and side panels 48

18 HIGHBAND FRAMES Frames specially designed to accommodate the Highband modules. Space efficient with built-in cable management. Available in 2 sizes. Highband modules - page 39 HIGH BAND 2 vert Highband frame Description Pack Qty Product Dimension Weight KRONE Product No 4 vert frame to hold up to 320 modules (h)x1203(w)x240(d) mm 70kg 6420/1/060/00 2 vert frame to hold up to 160 modules (h)x640(w)x240(d) mm 35kg 6420/1/060/01 12U CABINET 12U cabinet accommodates 19" patch panels and/or active equipment. Lockable door with acrylic window. Ventilation slots and cable management included. Suitable for both copper and fibre applications. Copper patch panels - page 33, Fibre patch panels - page 55,61, Accessories - page 51 12U cabinet Description Pack Qty Product Dimension Weight KRONE Product No 12U cabinet 1 593(h)x542(w)x505(d)mm 21kg 6527/1/500/00 FRAMES, RACKS AND CABINETS 49

19 ...

20 Accessories 51

21 INSERTION TOOL Tool for LSA-PLUS IDC termination. Inserts and crops wires simultaneously. Complete with extraction tool and stop clip. Also available with sensor, which ensures the conductor is fully inserted into the contact before allowing excess wire to be cut off. Insertion tool ACCESSORIES Insertion tool /1/810/02 Insertion tool with sensor /2/055/01 PATCH PANEL OUTRIGGER Attaches to a standard 19" rack, leaving both hands free for wiring patch panels. Patch panel outrigger Patch panel outrigger /1/013/00 Patch panel termination rail /1/627/00 19" JUMPER BARS Mounts onto a standard 19" rack to provide cable management for patchcords. 1U Jumper Bar 1U Plastic Rings /1/006/01 2U Metal Rings /1/022/00 52

22 PATCH SECURITY SYSTEM Prevents the insertion and removal of patchcords. Suitable for use with CL, LN and PCB panels. Patch security system Black /1/722/00 Red /1/722/02 Yellow /1/722/01 BLANKING PANELS Attaches to a standard 19" rack. ACCESSORIES Blank panel 2U 1U /1/007/01 2U /1/007/02 3U /1/007/03 53

23 ...

24 Fibre Pre-terminated fibre 55

25 KRONE s pre-terminated fibre system dispenses with the need for on-site termination. The system includes patch panel kits, wall mount kits in either MTP, FibreClip, MTRJ, SC or ST variants plus the required length of pre-terminated fibre optic cable. Available in multimode 62.5/125µm or 50/125µm. KRONE Pre-terminated MTP versus FibreClip FIBRE - PRE-TERMINATED FIBRE The FibreClip pre-terminated fibre solution has been developed to enable an optical link to be installed in the most cost-effective and fully interchangeable way. Moving away from the multi-fibre ferrule technology employed in MTP connectors while removing a connectorpair loss from each patch panel. The pre-terminated ferrules are connected directly into the FibreClip bodies which are mounted in the adaptors housed in the patch panel. This enables custom-configuration within the patch panel and ease of rectification if a fault occurs on any port. To aid the installer not familiar with fibre, the MTP solution remains a solution requiring the minimum level of skill and quickest installation time. PRE-TERMINATED MTP FIBRE CABLE To order KRONE Pre-terminated cable assemblies 1. Specify product number as listed below. 2. Specify required length (all variants are available in lengths of up to 1000m). Cable can be ordered in 5m increments up to 100m, 10m increments up to 500m, 20m increments up to 1000m. Pre-terminated MTP fibre cable assembly Description (UNIVERSAL CABLE) 4 core 8 core 12 core MTP/MTP terminated 62.5/125µm 7023/5/1 7023/6/1 7023/7/1 MTP/ST terminated 62.5/125µm 7023/5/2 7023/6/2 7023/7/2 MTP/SC terminated 62.5/125µm 7023/5/3 7023/6/3 7023/7/3 ST/ST terminated 62.5/125µm 7023/5/4 7023/6/4 7023/7/4 SC/SC terminated 62.5/125µm 7023/5/5 7023/6/5 7023/7/5 Contact KRONE sales for 50/125µm product numbers 56

26 PRE-TERMINATED MTP FIBRE PANELS/ENCLOSURES Pre-terminated enclosures and panels containing ST or SC adaptors and MTP hydras. Fully tested for insertion loss. All 62.5/125µm listed. 24 port ST pre-terminated fibre panel Description Pack Qty Connector Type PRE-TERMINATED MTP HYDRAS Preconnected assemblies with MTP at one end fanning out to a number of ST or SC connectors 62.5/125µm. Fully tested for insertion loss. 24 port ST pre-terminated wall mount enclosure 4 Port 8 Port 12 Port 16 Port 24 Port Wall mount 1 SC 7032/1/050/ /1/051/ /1/052/ /1/053/ /1/054/00 Wall mount 1 ST 7032/1/040/ /1/041/ /1/042/ /1/043/ /1/044/00 Patch panel 1 SC 7033/1/050/ /1/051/ /1/052/ /1/053/ /1/054/00 Patch panel 1 ST 7033/1/040/ /1/041/ /1/042/ /1/043/ /1/044/00 Contact KRONE sales for 50/125µm product numbers FIBRE - PRE-TERMINATED FIBRE Hydra 8, MTP/ST Hydra 4, MTP/ST 62.5/125µm /1/001/00 Hydra 8, MTP/ST 62.5/125µm /1/002/00 Hydra 12, MTP/ST 62.5/125µm /1/003/00 Hydra 4, MTP/SC 62.5/125µm /1/004/00 Hydra 8, MTP/SC 62.5/125µm /1/005/00 Hydra 12, MTP/SC 62.5/125µm /1/006/00 Contact KRONE sales for 50/125µm product numbers 57

27 PRE-TERMINATED MTP FIBRE ADAPTOR MODULES ST and SC adaptor plates for pre-terminated MTP fibre panels and enclosures. FIBRE - PRE-TERMINATED FIBRE MTP adaptor /3/020/00 MTP adaptor plate /1/100/00 blanking plate module /1/110/00 4 port ST adaptor module /1/111/00 8 port ST adaptor module /1/112/00 4 port (duplex) SC adaptor module /1/113/00 8 port (duplex) SC adaptor module /1/114/00 PRE-TERMINATED FIBRECLIP CABLE ASSEMBLIES To order KRONE pre-terminated FibreClip cable assemblies 1. Specify product number (cable type and no. of fibres). 2. Specify length required. Cable can be ordered in 5m increments up to 100m, 10m increments up to 500m, 20m increments up to 1000m. 4 port ST adaptor module 4 port (duplex) SC adaptor module Pre-terminated FibreClip cable assembly Description (UNIVERSAL CABLE) /125µm Pack Qty KRONE Product No 4 core FibreClip/FibreClip /5/6 8 core FibreClip/FibreClip /6/6 12 core FibreClip/FibreClip /7/6 For other cable constructions or fibre types contact KRONE sales. 58

28 FIBRECLIP PATCH PANELS Panels contain ST or SC presentation. Sliding draw design for easy access. 24 port SC FibreClip patch panel Description Pack Connector Qty Type 4 Port 8 Port 12 Port 16 Port 24 Port FibreClip patch panel 1 ST 7033/1/045/ /1/046/ /1/047/ /1/048/ /1/049/00 FibreClip patch panel 1 SC 7033/1/055/ /1/056/ /1/057/ /1/058/ /1/059/00 FIBRECLIP ACCESSORIES Description Pack Qty Connector Type KRONE Product No FibreClip adaptor kit 1 ST 7033/1/025/00 FibreClip adaptor kit 1 SC 7033/1/035/00 FIBRECLIP CONNECTOR ILLUSTRATION Note: Fibre-Clip patch panels contain SC/SC or SC/ST adaptors as required. FIBRE - PRE-TERMINATED FIBRE MT-RJ PRE-TERMINATED CABLE ASSEMBLIES TO ORDER MT-RJ CABLE ASSEMBLIES SPECIFY 1. Core 2 to 24 fibres 2. Type of termination (MT-RJ to MT-RJ, MT-RJ TO SC, MT-RJ to ST) 3. Universal 4. Length in metres. 59

29

30 Fibre Installer terminated fibre & outlets 61

31 INSTALLER TERMINATED PLASTIC FIBRE PATCH PANELS Plastic fibre patch panel for use with standard cabling or blown fibre systems. This light-weight and robust panel has sliding tray for easy access and modular adaptor plate configuration. An integral fibre management system removes the need for bunny clips or management stars. Accepts MT-RJ, SC Simplex, SC Duplex, ST, LC and FC adaptors. Open channels at rear for use with blown fibres. Knock-outs to enable termination of loose-tube or tight-buffered cables. 24 port MT-RJ plastic patch panel FIBRE - INSTALLER TERMINATED FIBRE & OUTLETS Description Pack Qty Connector Type Description Pack Qty Connector Type 4 Port 8 Port 12 Port 16 Port 24 Port Patch panel 1 MT-RJ 7033/1/076/ /1/076/ /1/076/ /1/076/ /1/076/24 Patch panel 1 SC Simplex 7033/1/078/ /1/078/ /1/078/ /1/078/ /1/078/24 Patch panel 1 SC Duplex 7033/1/080/ /1/080/ /1/080/ /1/080/ /1/080/24 Patch panel 1 ST 7033/1/082/ /1/082/ /1/082/ /1/082/ /1/082/24 Splice holder kit /2/018/00 INSTALLER TERMINATED METAL FIBRE PATCH PANELS/ENCLOSURES Patch panels and enclosures in FC, ST, SC and MT-RJ variants. Available in up to 24 port. Patch panels have sliding tray for easy access to fibre. 24 Port SC wall mount enclosure 24 Port ST patch panel 4 Port 8 Port 12 Port 16 Port 24 Port Wall mount 1 SC 7032/1/030/ /1/031/ /1/032/ /1/033/ /1/034/00 Wall mount 1 ST 7032/1/020/ /1/021/ /1/022/ /1/023/ /1/024/00 Patch panel 1 SC 7033/1/030/ /1/031/ /1/032/ /1/033/ /1/034/10 Patch panel 1 ST 7033/1/020/ /1/021/ /1/022/ /1/023/ /1/024/10 Patch panel 1 MT-RJ 7033/1/060/ /1/060/ /1/060/ /1/060/ /1/060/24 Patch panel 1 FC 7033/1/040/ /1/041/ /1/042/ /1/043/ /1/044/10 62

32 ACCESSORIES Accessories for fibre cable management and splicing. Adhesive fibre management star Adhesive fibre management star /1/123/00 Splice bridge /1/120/00 M20 strain relief gland & nut /1/121/00 M16 strain relief gland & nut /1/122/00 FIBRE WALL OUTLETS Outlets presenting MT-RJ, ST or SC sockets for fibre-to-the-user applications. Fully managed double gang footprint for blown and conventional cabling systems. Supplied with adaptors or empty as required. Integral fibre management system. Simple installation for fusion splicing of pigtails or direct termination. Splice protector holders and cable break-out units are also available if required. Splice bridge MT-RJ quad outlet MT-RJ dual outlet (2 sockets) /1/067/02 MT-RJ quad outlet (4 sockets) /1/067/04 1 SC duplex outlet /1/069/02 2 SC duplex outlet /1/069/04 2 ST outlet /1/071/02 4 ST outlet /1/071/04 FIBRE - INSTALLER TERMINATED FIBRE & OUTLETS 63

33 STANDARD FIBRE CONNECTORS & ADAPTORS Multimode fibre connectors and adaptors. Available in ST, SC and field installable as well as standard epoxy polish variants. FIBRE - INSTALLER TERMINATED FIBRE PATCH & OUTLETS PANELS ST connector SC connector SC duplex adaptor ST multimode connector (900µm and 3mm boots) /1/010/00 SC multimode connector (900µm and 3mm boots) /2/210/00 ST multimode field terminated connector (62.5/125µm) /1/113/00 SC multimode field terminated connector (62.5/125µm) /1/114/00 ST multimode adaptor /1/026/00 SC duplex multimode adaptor (phosphor bronze sleeve) /1/036/00 ST/SC duplex adaptor /3/071/00 Note: 50/125µm variants of field terminated connectors available upon request. See page 59 for field termination kit. 64

34 MT-RJ FIBRE CONNECTORS & ADAPTORS Connectors for epoxy polish available in either male (with guide pins) or female (without guide pins) and are suitable for 50µm or 62.5µm core multimode fibre. Field termination connectors are specific to the fibre core required and are installed using the Universal field termination kit. The shuttered socket can be used in the KRONE plastic patch panel and fibre outlet, while the Keystone mounting variant is generically mountable. Field installable MT-RJ connector UNIVERSAL FIELD TERMINATION KIT Suitable for ST, SC and MT-RJ field termination connectors. Kit contains cable/fibre preparation tools, fibre cleaver, crimp tool and installation guide. Includes carrying case and consumables required for cleaning fibres. Termination tool also available separately. MT-RJ connector (female, epoxy polish) MT-RJ connector MM (female) /1/019/00 MT-RJ connector MM (male) /1/019/01 Field termination MT-RJ connector 62.5/125µm /1/111/00 Field termination MT-RJ connector 50/125µm /1/112/00 MT-RJ shuttered socket /1/041/00 MT-RJ shuttered socket with keystone adaptor /1/030/00 Universal field tool kit Universal field termination tool kit /1/045/00 Universal termination tool /1/110/00 FIBRE - INSTALLER TERMINATED FIBRE & OUTLETS 65

35 SINGLE MODE FIBRE APPLICATIONS KRONE also provide a full range of single mode fibre assemblies for backbone and composite backbone solutions. Connectors and adaptors available include FC, SC, ST, E2000 and LC in UPC or APC format. LC CONNECTOR KRONE s Small Form Factor Connector for singlemode and multimode fibre. With a 1.25mm ferrule the LC provides for double the density of SC connectors. Typical Insertion Loss is 0.2dB and Return Loss >50dB for UPC connectors and >60dB for APC connectors. FIBRE - INSTALLER TERMINATED FIBRE & OUTLETS LC pigtails & patchcords - page 72 LC UPC connector LC UPC connector /1/001/00 LC APC connector /1/004/00 LC ADAPTOR Adaptors available for multimode, singlemode UPC and APC. Duplex adaptor has same foot-print as simplex SC. LC pigtails & patchcords - page 72 LC adaptor (APC - left, UPC - right) LC adaptor UPC /1/019/00 LC adaptor APC /1/020/00 66

36 Fibre Cable Assemblies 67

37 STANDARD FIBRE PIGTAILS 0.9mm multimode, PVC, 62.5/125µm & 50/125µm. Tested for insertion loss better than 0.5dB, typically 0.2dB. FIBRE - CABLE ASSEMBLIES SC 1m 62.5/125µm /3/110/11 SC 2m 62.5/125µm /3/110/12 SC 3m 62.5/125µm /3/110/13 SC 5m 62.5/125µm /3/110/15 ST 1m 62.5/125µm /3/150/11 ST 2m 62.5/125µm /3/150/12 ST 3m 62.5/125µm /3/150/13 ST 5m 62.5/125µm /3/150/15 MT-RJ FIBRE PIGTAILS Multimode pigtails available in both 50/125µm and 62.5/125µm variants. Standard length 1m, however other lengths can be supplied as required. Fibre is secondary coated (600µm) and terminated with a male MT-RJ connector (with guide pins). 2M SC pigtail 2M ST pigtail MT-RJ pigtail MT-RJ pigtail 50/125µm 1m /1/028/01 MT-RJ pigtail 50/125µm 2m /1/028/02 MT-RJ pigtail 62.5/125µm 1m /1/029/01 MT-RJ pigtail 62.5/125µm 2m /1/029/02 68

38 SIMPLEX FIBRE PATCHCORDS 2.8mm, low smoke sheath, multimode 62.5/125µm & 50/125µm. Tested for insertion loss better than 0.5dB, typically 0.2dB. SC/SC 1m 62.5/125µm /3/211/11 SC/SC 2m 62.5/125µm /3/211/12 SC/SC 3m 62.5/125µm /3/211/13 SC/SC 5m 62.5/125µm /3/211/15 ST/SC 1m 62.5/125µm /3/251/11 ST/SC 2m 62.5/125µm /3/251/12 ST/SC 3m 62.5/125µm /3/251/13 ST/SC 5m 62.5/125µm /3/251/15 ST/ST 1m 62.5/125µm /3/255/11 ST/ST 2m 62.5/125µm /3/255/12 ST/ST 3m 62.5/125µm /3/255/13 ST/ST 5m 62.5/125µm /3/255/15 2M SC/SC simplex patchcord 2M ST/ST patchcord Contact KRONE sales for 50/125µm product numbers FIBRE - CABLE ASSEMBLIES 69

39 FIBRE DUPLEX PATCHCORDS Designed to provide one-to-one connectivity from end to end. However, ensure that a cross over is provided in the link to guarantee that the equipment transmit to receive paths are maintained. Low smoke sheath, 62.5/125µm listed (also available in 50/125µm). Tested for insertion loss better than 0.5dB, typically 0.2dB. FIBRE - CABLE ASSEMBLIES SC/SC DISCRETE 1m /3/511/11 SC/SC DISCRETE 2m /3/511/12 SC/SC DISCRETE 3m /3/511/13 SC/SC DISCRETE 5m /3/511/15 ST/SC DISCRETE 1m /3/551/11 ST/SC DISCRETE 2m /3/551/12 ST/SC DISCRETE 3m /3/551/13 ST/SC DISCRETE 5m /3/551/15 ST/ST DISCRETE 1m /3/555/11 ST/ST DISCRETE 2m /3/555/12 ST/ST DISCRETE 3m /3/555/13 ST/ST DISCRETE 5m /3/555/15 ST/SC DUPLEX 1m /3/557/11 ST/SC DUPLEX 2m /3/557/12 ST/SC DUPLEX 3m /3/557/13 ST/SC DUPLEX 5m /3/557/15 SC/SC DUPLEX 1m /3/577/11 2M SC/SC discrete duplex patchcord 2M ST/ST duplex patchcord 2M SC/SC duplex patchcord SC/SC DUPLEX 2m /3/577/12 SC/SC DUPLEX 3m /3/577/13 SC/SC DUPLEX 5m /3/577/15 70

40 MT-RJ PATCHCORDS Full range of patchcords for both 50/125µm and 62.5/125µm fibre, MT-RJ to MT-RJ and hybrid assemblies with ST or SC connectors. Full range of lengths from 1 to 20 metres using mini-zip duplex low smoke cables. MT-RJ to MT-RJ patchcord MT-RJ to SC duplex patchcord MT-RJ to duplex ST patchcord Description Fibre size Pack Qty KRONE Product No MT-RJ to MT-RJ 1m 62.5/125µm /1/023/01 MT-RJ to MT-RJ 2m 62.5/125µm /1/023/02 MT-RJ to MT-RJ 3m 62.5/125µm /1/023/03 MT-RJ to MT-RJ 5m 62.5/125µm /1/023/05 MT-RJ to MT-RJ 1m 50/125µm /1/033/01 MT-RJ to MT-RJ 2m 50/125µm /1/033/02 MT-RJ to MT-RJ 3m 50/125µm /1/033/03 MT-RJ to MT-RJ 5m 50/125µm /1/033/05 MT-RJ to SC duplex 1m 62.5/125µm /1/024/01 MT-RJ to SC duplex 2m 62.5/125µm /1/024/02 MT-RJ to SC duplex 3m 62.5/125µm /1/024/03 MT-RJ to SC duplex 5m 62.5/125µm /1/024/05 FIBRE - CABLE ASSEMBLIES MT-RJ to SC duplex 1m 50/125µm /1/037/01 MT-RJ to SC duplex 2m 50/125µm /1/037/02 MT-RJ to SC duplex 3m 50/125µm /1/037/03 MT-RJ to SC duplex 5m 50/125µm /1/037/05 MT-RJ to duplex ST 1m 62.5/125µm /1/025/01 MT-RJ to duplex ST 2m 62.5/125µm /1/025/02 MT-RJ to duplex ST 3m 62.5/125µm /1/025/03 MT-RJ to duplex ST 5m 62.5/125µm /1/025/05 MT-RJ to duplex ST 1m 50/125µm /1/035/01 MT-RJ to duplex ST 2m 50/125µm /1/035/02 MT-RJ to duplex ST 3m 50/125µm /1/035/03 MT-RJ to duplex ST 5m 50/125µm /1/035/05 For part numbers of other lengths of patchcord please contact KRONE SALES. 71

41 SINGLE MODE FIBRE APPLICATIONS LC FIBRE PIGTAILS Small form factor (SFF) connector pigtails for singlemode fibre available in UPC and APC formats in a variety of lengths. The LC enables high density connection using a ceramic 1.25mm ferrule with push/pull matability, typically half the size of an SC connector. Multimode pigtails (62.5/125µm and 50/125µm) also available upon request. FIBRE - CABLE ASSEMBLIES LC FIBRE PATCHCORDS Small form factor (SFF) connector patchcord configured with one (simplex) or two (duplex) fibres. Available in UPC or APC format and in a variety of lengths. Assemblies for 2 fibres employ a duplexing clip. Hybrid assemblies using FC or SC connectors also available upon request. Multimode pigtails (62.5/125µm and 50/125µm) also available upon request. LC fibre pigtail LC UPC pigtail 1m /1/180/51 LC APC pigtail 1m /1/180/31 For part numbers of other lengths of pigtail please contact KRONE SALES. LC simplex patchcord LC duplex patchcord LC to LC UPC simplex patchcord 1m /1/688/51 LC to LC APC simplex patchcord 1m /1/688/31 LC to LC UPC duplex patchcord 1m /1/788/51 LC to LC APC duplex patchcord 1m /1/788/31 For part numbers of other lengths of patchcord please contact KRONE SALES. KRONE also provide a full range of single mode fibre assemblies for backbone and composite backbone solutions. Connectors and adaptors available include FC, SC, ST, E2000 and LC in UPC or APC format. 72