EMC ilters 4-line ilters or installations and systems Rated current 6 to 125 A Series/Type: Date: January 2006 EPCOS AG 2006. Reproduction, publication and dissemination o this data sheet and the inormation contained therein without EPCOS prior express consent is prohibited.
4-line ilters or installations and systems Power line ilters or 3-phase systems Rated voltage 440/250 V AC, 50/60 Hz Rated current 6 to 125 A Construction 4-line ilter Metal case Features High insertion loss Compact, cost-optimized design Easy to install ENEC10, UL and CSA approval Applications Power supplies or data systems, telecom systems medical equipment, industrial installations copiers Terminals Tab connectors 6.3 0.8 mm Screw terminals Marking Marking on component: Manuacturer s logo, ordering code, rated voltage, rated current, rated temperature, climatic category, date code Minimum marking on packaging: Manuacturer s logo, ordering code Circuit diagram LINE LOAD L1 L1 L2 L2 L3 L3 N N SSB0338-G Important notes at the end o this document. 2 01/06
4-line ilters or installations and systems Technical data and measuring conditions Rated voltage V R Rated current I R Test voltage V test Leakage current l leak Climatic category (IEC 60068-1) Approvals 440/250 V AC, 50/60 Hz Reerred to 40 C ambient temperature 1770 V DC, 2 s (line/line) 2700 V DC, 2 s (lines/case) At 400 V AC, 50 Hz 25/085/21 ( 25 C/+85 C/21 days damp heat test) EN 133200, UL 1283, CSA C22.2 No.8 Characteristics and ordering codes V R AC V I R A I leak ma Approx. weight kg Ordering code Approvals 440/250 6 < 3.5 0.8 A0006A001 16 < 3.5 1.5 M0003A116 25 < 3.5 2.3 M0001G125 35 < 3.5 2.3 M0001G135 35 < 3.5 2.3 M0001H135 50 < 3.5 4.5 M0002G150 63 < 3.5 4.5 M0002G163 80 < 3.5 12.5 M0004G180 125 < 3.5 12.5 M0004G225 = approval granted Important notes at the end o this document. 3 01/06
4-line ilters or installations and systems Dimensional drawings A0006A001 (6 A) 162±1 135±0.8 30±0.2 L3 L2 N L1 46±0.5 L2 L3 L1 N 20±0.5 Tab connector A6.3 x 0.8 M5 (4x) 13±0.5 LINE LOAD 62±0.5 75±0.2 87±1 44±0.2 SSB0958-X-E M0003A116 (16 A) 174.5 149 Tab connector A6.3 x 0.8 104 15.1 24.6 24.6 24.6 50 36 13.5 52.5 44±0.2 52 M5 x 6 1) 14.5 75±0.3 1) Also suitable or screws with 10-32 UNF thread SSB0339-P-E Important notes at the end o this document. 4 01/06
4-line ilters or installations and systems M0001G125, M0001G135/H135 (25 A, 35 A) 23 149 104 M6 and/or 15 10-32 UNF 15.1 24.6 24.6 24.6 80 33.5 14±0.3 52.5±0.8 44±0.2 M5 x 6 1) 14.5 52 75±0.3 1) Also suitable or screws with 10-32 UNF thread SSB0321-L-E Type M0001 I R A Screw thread G125 25 M6 3 G135 35 M6 3 H135 35 10-32 UNF 2 Tightening torque Nm M0002G150, M0002G163 (50 A, 63 A) Screw thread M6 23 141 Tightening torque 3 Nm 131 28.6 24.6 24.6 24.6 122 21.8 M6 47 48.5 44±0.2 M5 x 6 1) 65.5 13 105±0.3 1) Also suitable or screws with 10-32 UNF thread SSB0322-U-E Important notes at the end o this document. 5 01/06
4-line ilters or installations and systems M0004G180, M0004G225 (80 A, 125 A) Screw thread M10 35±0.8 220±1.2 Tightening torque 10 Nm 150±1.2 35±0.8 35±0.8 35±0.8 150±1.2 30±0.5 25±0.5 M10 160±0.3 M5 x 6 1) 120±0.3 1) Also suitable or screws with 10-32 UNF thread SSB0544-3-E Important notes at the end o this document. 6 01/06
4-line ilters or installations and systems Insertion loss (typical values at Z = 50 Ω) unsymmetrical, adjacent branches terminated common mode, all branches in parallel (asymmetrical) dierential mode (symmetrical) Filters or 6 A Filters or 16 A SSB1063-I A0006A001 80 80 M0003A116 SSB0342-9 60 60 40 40 20 20 0 0 10 4 10 5 10 6 10 7 Hz 10 8 10 4 10 5 10 6 10 7 Hz 10 8 Filters or 25 A Filters or 35 A SSB1676-H M0001G125 80 80 M0001G135 M0001H135 SSB0343-H 60 60 40 40 20 20 0 0 10 4 10 5 10 6 10 7 Hz 10 8 10 4 10 5 10 6 10 7 Hz 10 8 Important notes at the end o this document. 7 01/06
4-line ilters or installations and systems Insertion loss (typical values at Z = 50 Ω) unsymmetrical, adjacent branches terminated common mode, all branches in parallel (asymmetrical) dierential mode (symmetrical) Filters or 50 A Filters or 63 A M0002G150 SSB0541-D 80 80 M0002G163 SSB0345-Y 60 60 40 40 20 20 0 0 10 4 10 5 10 6 10 7 Hz 10 8 10 4 10 5 10 6 10 7 Hz 10 8 Filters or 80 A Filters or 125 A M0004G180 SSB0545-B 80 80 M0004G225 SSB0546-J 60 60 40 40 20 20 0 0 10 4 10 5 10 6 10 7 Hz 10 8 10 4 10 5 10 6 10 7 Hz 10 8 Important notes at the end o this document. 8 01/06
EMC ilters Cautions and warnings Important inormation Please read all saety and warning notes careully beore installing the EMC ilter and putting it into operation (see ). The same applies to the warning signs on the ilter. Please ensure that the signs are not removed nor their legibility impaired by external inluences. Death, serious bodily injury and substantial material damage to equipment may occur i the appropriate saety measures are not carried out or the warnings in the text are not observed. Using according to the terms The EMC ilters may be used only or their intended application within the speciied values in lowvoltage networks in compliance with the instructions given in the data sheets and the data book. The conditions at the place o application must comply with all speciications or the ilter used. Warnings It shall be ensured that only qualiied persons (electricity specialists) are engaged on work such as planning, assembly, installation, operation, repair and maintenance. They must be provided with the corresponding documentation. Danger o electric shock. EMC ilters contain components that store an electric charge. Dangerous voltages can continue to exist at the ilter terminals or longer than ive minutes even ater the power has been switched o. The protective earth connections shall be the irst to be made when the EMC ilter is installed and the last to be disconnected. Depending on the magnitude o the leakage currents, the particular speciications or making the protective-earth connection must be observed. Impermissible overloading o the EMC ilter, such as impermissible voltages at higher requencies that may cause resonances etc. can lead to destruction o the ilter housing. EMC ilters must be protected in the application against impermissible exceeding o the rated currents by suitable overcurrent protective. 9 01/06
EMC ilters Important notes The ollowing applies to all products named in this publication: 1. Some parts o this publication contain statements about the suitability o our products or certain areas o application. These statements are based on our knowledge o typical requirements that are oten placed on our products in the areas o application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability o our products or a particular customer application. As a rule, EPCOS is either unamiliar with individual customer applications or less amiliar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product speciication is suitable or use in a particular customer application. 2. We also point out that in individual cases, a malunction o passive electronic components or ailure beore the end o their usual service lie cannot be completely ruled out in the current state o the art, even i they are operated as speciied. In customer applications requiring a very high level o operational saety and especially in customer applications in which the malunction or ailure o a passive electronic component could endanger human lie or health (e.g. in accident prevention or lie-saving systems), it must thereore be ensured by means o suitable design o the customer application or other action taken by the customer (e.g. installation o protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event o malunction or ailure o a passive electronic component. 3. The warnings, cautions and product-speciic notes must be observed. 4. In order to satisy certain technical requirements, some o the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous ). Useul inormation on this will be ound in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales oices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change rom time to time. The same is true o the corresponding product speciications. Please check thereore to what extent product descriptions and speciications contained in this publication are still applicable beore or when you place an order. We also reserve the right to discontinue production and delivery o products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version o the General Terms o Delivery or Products and Services in the Electrical Industry published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-Jones, Baoke, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further inormation will be ound on the Internet at www.epcos.com/trademarks. 10 01/06
Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Liecycle Inormation: EPCOS: M2G163 M3A116 M4G225 M1G125 A6A1 M4G180 M1H135