1
2
Asse mbly Instructions Clearlight Infrare d Sauna: CE-1 Part List...4 Pre-Assembly Instructions...5 Assembly Instructions...6-8 Control Panel Instructions...9 Color Light Therapy Instructions...10 Using your Clearlight Infrared Sauna...11 Tips...12-13 Safety Instructions...14 Safeguards...15 Warranty and Contact Information...16 Specifications...17 3
Parts List 1) Roof Panel 2) Front Panel 3) Back Wall 4) Right Side Wall Panel 5) Left Side Wall Panel 6) Bench 7) Under Bench Support 8) Floor Panel 9) Radio Remote Control 10) Keypad Remote Control 11) Magazine Rack 12) Towel Rack 4
READ BEFORE INSTALLATION: Panels may be heavy. Be careful to avoid injury when installing. Two adults are required for the installation of your sauna There is a + button or a button at the side of each panel. The panels will be installed by corresponding one + panel to one panel as below at the time of install. The panel with the + button should be lifted up about 4 inches (10cm) higher than the panel with the - button (Refer to Picture 1). Place the + panel against the panel (Refer to Picture 2), and then slide down the panel with + button until the two panels are equal in height (Refer to Picture 3). If they are not equal in height or there is an obvious gap between the two panels, this means they are not properly attached, and you should try again. The pane ls should be installe d in the following orde r: 1. Floor 2. Back Wall 3. Left Side Wall 4. Right Side Wall 5. Unde r Be nch Support 6. Bench 7. Front Wall 8. Roof 5
Assembly Instructions 1) Place the floor in the desired location on a level surface (Note: The floor panel must be level before installing the wall and roof panels. If the surface is not level you may need to shim the bottom panel to make it level.) 2) Place back wall in the slot of floor. 3) Place the right side wall in the slot of floor. 4) Place the left side wall in the slot of floor. 6
5) Installing the Under Bench Support and Bench: Slide the Under Bench Support Panel down the wooden supports with the heater facing out. Make sure the two side slots of the Bench Support Panel slide completely into the corresponding grooves of the wooden supports. (Refer to Photo 1) Connect the power connector from the back of the Under Bench Support Panel to the floor Panel then connect the other power connector from the back of Under Bench Support Panel to the Right Wall Panel. Ensure the connection is completely fastened (Refer to Photo 2) Place the Bench on the Bench Support Panel and slide toward the Back Wall until flush to the Back Wall. (Refer to Photo 3) 1 2 3 6) Place the front panel in the slot of floor panel. 7) Place the top panel on the four side panels. Make sure the connection wires from the three side panels protrude through the corresponding holes of the top panel. Make sure the top panel s arched side is facing to the front. Make sure the wire is through each hole smoothly and completely. Make sure trim of the top panel fits completely around the four side panels. 7
8) Make sure each of the lead wires on the top of the left, right, back and front panels is protruding through the top panel; then plug each of the four lead wires into the four connectors of the top panel as in the photo below 9) Remove the screws used to lock the AM/FM/CD player before using. 10) Congratulation! You have finished the installation of your ne w Clearlight Infrared Sauna. 8
CONTROL PANEL INSTRUCTION 1) Press POWER to turn your sauna on or off. 2) TIME refers to the amount of time for your sauna session. Once your sauna is powered on, the default session time of 45 minutes will be displayed. Press UP Arrow or DOWN Arrow to adjust and set the maximum time for your sauna session; pressing once will increase or decrease the time in 5 minute increments. The maximum operating time is 60 minutes. After the session time is set, the number will flash for about three seconds. After the set Time stops flashing, the remaining time, in minutes, will be displayed. 3) TEMP shows the current temperature inside the sauna and allows you to set a maximum temperature for your session. Celcius/Fahrenheit allows you to switch the displayed temperature in either Celcius or Fahrenheit. Press UP Arrow or DOWN Arrow below the temperature display to adjust and set the temperature in the sauna room; pressing once will increase in one degree increments. The maximum set temperature is 150 F / 65 C. After you set the sauna temperature, the set temperature displayed will flash for about 5 seconds. After the numbers of the set temperature stop flashing, the number indicated will show actual air temperature inside sauna room. 4) Press Outside to turn on or off the outside lights. 5) Press Inside to turn on or off the inside lights and press Outside to turn on or off the outside lights. Note: The remote controller is operates the same as above. 9
OPERATING INSTRUCTIONS FOR COLOR LIGHT THERAPY SYSTEM 1. To activate the color light therapy system press the Color Light button on the sauna control panel. Upon turning the system on, the color light system will go into an automatically cycling mode, changing color every 8 seconds: 2. Press the Color Light button 2 times: Light system will glow GREEN 3. Press the Color Light button 3 times: Light system will glow RED 4. Press the Color Light button 4 times: Light system will glow BLUE 5. Press the Color Light button 5 times: Light system will glow YELLOW 6. Press the Color Light button 6 times: Light system will glow TURQUOISE 7. Press the Color Light button 7 times: Light system will glow VIOLET 8. Press the Color Light button 8 times: Light system will turn OFF 9. The Color Light System automatically turns off when the sauna is turned OFF. 10
11
12
13
14
15
16
SPECIFICATION Product Name Clearlight Infrare d Sauna Product No. Product Size CE-2 39.25 x 44 x 76.5 IN / 100 x 112 x 194 CM Weight Power Supply 350lbs / 158kg?AC120V?AC220V?AC230V?AC240V Power Consumption Wooden Material 1,410W?Nordic Spruce? Canadian Red Ce dar Manufacture Address Clearlight Infrare d Saunas / Sauna Works 2184 Sutter St. #282 San Francisco, CA 94115 17